The new bitsliced NEON implementation of AES uses a fallback in two
places: CBC encryption (which is strictly sequential, whereas this
driver can only operate efficiently on 8 blocks at a time), and the
XTS tweak generation, which involves encrypting a single AES block
with a different key schedule.
The plain (i.e., non-bitsliced) NEON code is more suitable as a fallback,
given that it is faster than scalar on low end cores (which is what
the NEON implementations target, since high end cores have dedicated
instructions for AES), and shows similar behavior in terms of D-cache
footprint and sensitivity to cache timing attacks. So switch the fallback
handling to the plain NEON driver.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The non-bitsliced AES implementation using the NEON is highly sensitive
to micro-architectural details, and, as it turns out, the Cortex-A53 on
the Raspberry Pi 3 is a core that can benefit from this code, given that
its scalar AES performance is abysmal (32.9 cycles per byte).
The new bitsliced AES code manages 19.8 cycles per byte on this core,
but can only operate on 8 blocks at a time, which is not supported by
all chaining modes. With a bit of tweaking, we can get the plain NEON
code to run at 22.0 cycles per byte, making it useful for sequential
modes like CBC encryption. (Like bitsliced NEON, the plain NEON
implementation does not use any lookup tables, which makes it easy on
the D-cache, and invulnerable to cache timing attacks)
So tweak the plain NEON AES code to use tbl instructions rather than
shl/sri pairs, and to avoid the need to reload permutation vectors or
other constants from memory in every round. Also, improve the decryption
performance by switching to 16x8 pmul instructions for the performing
the multiplications in GF(2^8).
To allow the ECB and CBC encrypt routines to be reused by the bitsliced
NEON code in a subsequent patch, export them from the module.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Shuffle some instructions around in the __hround macro to shave off
0.1 cycles per byte on Cortex-A57.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Using simple adrp/add pairs to refer to the AES lookup tables exposed by
the generic AES driver (which could be loaded far away from this driver
when KASLR is in effect) was unreliable at module load time before commit
41c066f2c4 ("arm64: assembler: make adr_l work in modules under KASLR"),
which is why the AES code used literals instead.
So now we can get rid of the literals, and switch to the adr_l macro.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the unnecessary alignmask: it is much more efficient to deal with
the misalignment in the core algorithm than relying on the crypto API to
copy the data to a suitably aligned buffer.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the unnecessary alignmask: it is much more efficient to deal with
the misalignment in the core algorithm than relying on the crypto API to
copy the data to a suitably aligned buffer.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the unnecessary alignmask: it is much more efficient to deal with
the misalignment in the core algorithm than relying on the crypto API to
copy the data to a suitably aligned buffer.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update the ARMv8 Crypto Extensions and the plain NEON AES implementations
in CBC and CTR modes to return the next IV back to the skcipher API client.
This is necessary for chaining to work correctly.
Note that for CTR, this is only done if the request is a round multiple of
the block size, since otherwise, chaining is impossible anyway.
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is a reimplementation of the NEON version of the bit-sliced AES
algorithm. This code is heavily based on Andy Polyakov's OpenSSL version
for ARM, which is also available in the kernel. This is an alternative for
the existing NEON implementation for arm64 authored by me, which suffers
from poor performance due to its reliance on the pathologically slow four
register variant of the tbl/tbx NEON instruction.
This version is about ~30% (*) faster than the generic C code, but only in
cases where the input can be 8x interleaved (this is a fundamental property
of bit slicing). For this reason, only the chaining modes ECB, XTS and CTR
are implemented. (The significance of ECB is that it could potentially be
used by other chaining modes)
* Measured on Cortex-A57. Note that this is still an order of magnitude
slower than the implementations that use the dedicated AES instructions
introduced in ARMv8, but those are part of an optional extension, and so
it is good to have a fallback.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This adds a scalar implementation of AES, based on the precomputed tables
that are exposed by the generic AES code. Since rotates are cheap on arm64,
this implementation only uses the 4 core tables (of 1 KB each), and avoids
the prerotated ones, reducing the D-cache footprint by 75%.
On Cortex-A57, this code manages 13.0 cycles per byte, which is ~34% faster
than the generic C code. (Note that this is still >13x slower than the code
that uses the optional ARMv8 Crypto Extensions, which manages <1 cycles per
byte.)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In addition to wrapping the AES-CTR cipher into the async SIMD wrapper,
which exposes it as an async skcipher that defers processing to process
context, expose our AES-CTR implementation directly as a synchronous cipher
as well, but with a lower priority.
This makes the AES-CTR transform usable in places where synchronous
transforms are required, such as the MAC802.11 encryption code, which
executes in sotfirq context, where SIMD processing is allowed on arm64.
Users of the async transform will keep the existing behavior.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is a straight port to arm64/NEON of the x86 SSE3 implementation
of the ChaCha20 stream cipher. It uses the new skcipher walksize
attribute to process the input in strides of 4x the block size.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull swiotlb fixes from Konrad Rzeszutek Wilk:
"This has one fix to make i915 work when using Xen SWIOTLB, and a
feature from Geert to aid in debugging of devices that can't do DMA
outside the 32-bit address space.
The feature from Geert is on top of v4.10 merge window commit
(specifically you pulling my previous branch), as his changes were
dependent on the Documentation/ movement patches.
I figured it would just easier than me trying than to cherry-pick the
Documentation patches to satisfy git.
The patches have been soaking since 12/20, albeit I updated the last
patch due to linux-next catching an compiler error and adding an
Tested-and-Reported-by tag"
* 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: Export swiotlb_max_segment to users
swiotlb: Add swiotlb=noforce debug option
swiotlb: Convert swiotlb_force from int to enum
x86, swiotlb: Simplify pci_swiotlb_detect_override()
Commit c02433dd6d ("arm64: split thread_info from task stack")
inverted the relationship between get_current() and
current_thread_info(), with sp_el0 now holding the current task_struct
rather than the current thead_info. The new implementation of
get_current() prevents the compiler from being able to optimize repeated
calls to either, resulting in a noticeable penalty in some
microbenchmarks.
This patch restores the previous optimisation by implementing
get_current() in the same way as our old current_thread_info(), using a
non-volatile asm statement.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Recent changes made KERN_CONT mandatory for continued lines. In the
absence of KERN_CONT, a newline may be implicit inserted by the core
printk code.
In show_pte, we (erroneously) use printk without KERN_CONT for continued
prints, resulting in output being split across a number of lines, and
not matching the intended output, e.g.
[ff000000000000] *pgd=00000009f511b003
, *pud=00000009f4a80003
, *pmd=0000000000000000
Fix this by using pr_cont() for all the continuations.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- DT: GXL: fix GPIO include
- add DT and defconfig for newly merged DRM driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=7ngo
-----END PGP SIGNATURE-----
Merge tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes
Pull "Amlogic fixes for v4.10" from Kevin Hilman:
- DT: GXL: fix GPIO include
- add DT and defconfig for newly merged DRM driver
This pull has one real fix, as a couple non-critical ones. The DRM
DT/defconfig patches are coming now because I didn't expect the new
driver to make it for the v4.10 merge window, but since it did[1], the
DT and defconfig should go into the same release.
[1] bbbe775ec5 drm: Add support for Amlogic Meson Graphic Controller
* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: defconfig: enable DRM_MESON as module
ARM64: dts: meson-gx: Add Graphic Controller nodes
ARM64: dts: meson-gxl: fix GPIO include
A simple fix to extend GICv2 CPU interface registers from 4K to 8K
on AEMv8 FVP/RTSM models in order to support split priority drop and
interrupt deactivation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCAAGBQJYZn50AAoJEABBurwxfuKYlUYQAJ4qNonGGnzErQE7bdYS2M+A
fB2R14lhDmCx9HZ7K3ld00x1gaKMJsh1uEU+WXpAt+AFEtJWEaEvWrxcBAY7fQRU
HWs/127+AQgpvKEgVMyOCoc+jj80HipoRMCCzfTZYpbI3LxfvQ7OwV47JpnKmo92
KO/4KZRvODBkupEkMF27ZtrScipLvHsgaYo2H2M2V/AatZ2e1XwGa6r0dxSqauuR
ZEc0C6i3ln8HGOikPwaf5o11MA+m4GHKPQJ55tRjjvn0dIxrh4rshvt+Fiu4h/eX
ImYAtsJS0PhZhRoqamWcfpzKhHQyQF6K05lX2AGBpKEuYjURqSppnndi43oGPIXw
WMe2uS6Ay6Xs9X/viBEJY5B4Cs6STVBVKERJGglHktHn2RGlzLS47XINH/yvOjiv
cbMqTe/PMYgh13QwpQjcuVkgDqhG2LlxueHaptEmJAW0X+juJQVgvSdmb359pn3O
sq+4omo3Z7KnHjBAwDOHVOB9fqTMLNJ/E9MIqEjZ1JrbMmI6C+JUxHBYJ9+Rm9jc
iSkgW1B9I/0lr5kNFLdsvvi9o5yPouZZvOB7DQoj8wnY0NqvmEVNLSRiCsuU4BkT
SFIxo+BK+jLrlAf6imB7jPpl8pM3KL0/BpsvBFRdq7iI7KNUxlPneQNKXYQO1sii
Gh1HgcgTCylRbPqYXhDD
=BoKJ
-----END PGP SIGNATURE-----
Merge tag 'juno-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes
Pull "ARMv8 Juno/VExpress fixes for v4.10" from Sudeep Holla:
A simple fix to extend GICv2 CPU interface registers from 4K to 8K
on AEMv8 FVP/RTSM models in order to support split priority drop and
interrupt deactivation.
* tag 'juno-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: vexpress: Support GICC_DIR operations
* Provide sd0_uhs node
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XZkS
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Renesas ARM Based SoC Fixes for v4.10
* Provide sd0_uhs node
* tag 'renesas-fixes-for-v4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: h3ulcb: Provide sd0_uhs node
Add Video Processing Unit and CVBS Output nodes, and enable CVBS on selected
boards.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The GICv2 CPU interface registers span across 8K, not 4K as indicated in
the DT. Only the GICC_DIR register is located after the initial 4K
boundary, leaving a functional system but without support for separately
EOI'ing and deactivating interrupts.
After this change the system supports split priority drop and interrupt
deactivation. This patch is based on similar one from Christoffer Dall:
commit 368400e242 ("ARM: dts: vexpress: Support GICC_DIR operations")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
This patch adds required memory carveouts so that the kernel does not
access memory that is in use or has been reserved for use by other remote
processors.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull SMP hotplug notifier removal from Thomas Gleixner:
"This is the final cleanup of the hotplug notifier infrastructure. The
series has been reintgrated in the last two days because there came a
new driver using the old infrastructure via the SCSI tree.
Summary:
- convert the last leftover drivers utilizing notifiers
- fixup for a completely broken hotplug user
- prevent setup of already used states
- removal of the notifiers
- treewide cleanup of hotplug state names
- consolidation of state space
There is a sphinx based documentation pending, but that needs review
from the documentation folks"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/armada-xp: Consolidate hotplug state space
irqchip/gic: Consolidate hotplug state space
coresight/etm3/4x: Consolidate hotplug state space
cpu/hotplug: Cleanup state names
cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
staging/lustre/libcfs: Convert to hotplug state machine
scsi/bnx2i: Convert to hotplug state machine
scsi/bnx2fc: Convert to hotplug state machine
cpu/hotplug: Prevent overwriting of callbacks
x86/msr: Remove bogus cleanup from the error path
bus: arm-ccn: Prevent hotplug callback leak
perf/x86/intel/cstate: Prevent hotplug callback leak
ARM/imx/mmcd: Fix broken cpu hotplug handling
scsi: qedi: Convert to hotplug state machine
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Move some Linux-specific functionality to upstream ACPICA and
update the in-kernel users of it accordingly (Lv Zheng).
- Drop a useless warning (triggered by the lack of an optional
object) from the ACPI namespace scanning code (Zhang Rui).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=55TG
-----END PGP SIGNATURE-----
Merge tag 'acpi-extra-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Here are new versions of two ACPICA changes that were deferred
previously due to a problem they had introduced, two cleanups on top
of them and the removal of a useless warning message from the ACPI
core.
Specifics:
- Move some Linux-specific functionality to upstream ACPICA and
update the in-kernel users of it accordingly (Lv Zheng)
- Drop a useless warning (triggered by the lack of an optional
object) from the ACPI namespace scanning code (Zhang Rui)"
* tag 'acpi-extra-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / osl: Remove deprecated acpi_get_table_with_size()/early_acpi_os_unmap_memory()
ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users
ACPICA: Tables: Allow FADT to be customized with virtual address
ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel
ACPI: do not warn if _BQC does not exist
* acpica:
ACPI / osl: Remove deprecated acpi_get_table_with_size()/early_acpi_os_unmap_memory()
ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users
ACPICA: Tables: Allow FADT to be customized with virtual address
ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel
* acpi-scan:
ACPI: do not warn if _BQC does not exist
Since all users are cleaned up, remove the 2 deprecated APIs due to no
users.
As a Linux variable rather than an ACPICA variable, acpi_gbl_permanent_mmap
is renamed to acpi_permanent_mmap to have a consistent coding style across
entire Linux ACPI subsystem.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch removes the users of the deprectated APIs:
acpi_get_table_with_size()
early_acpi_os_unmap_memory()
The following APIs should be used instead of:
acpi_get_table()
acpi_put_table()
The deprecated APIs are invented to be a replacement of acpi_get_table()
during the early stage so that the early mapped pointer will not be stored
in ACPICA core and thus the late stage acpi_get_table() won't return a
wrong pointer. The mapping size is returned just because it is required by
early_acpi_os_unmap_memory() to unmap the pointer during early stage.
But as the mapping size equals to the acpi_table_header.length
(see acpi_tb_init_table_descriptor() and acpi_tb_validate_table()), when
such a convenient result is returned, driver code will start to use it
instead of accessing acpi_table_header to obtain the length.
Thus this patch cleans up the drivers by replacing returned table size with
acpi_table_header.length, and should be a no-op.
Reported-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Convert the flag swiotlb_force from an int to an enum, to prepare for
the advent of more possible values.
Suggested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Pull x86 fixes and cleanups from Thomas Gleixner:
"This set of updates contains:
- Robustification for the logical package managment. Cures the AMD
and virtualization issues.
- Put the correct start_cpu() return address on the stack of the idle
task.
- Fixups for the fallout of the nodeid <-> cpuid persistent mapping
modifciations
- Move the x86/MPX specific mm_struct member to the arch specific
mm_context where it belongs
- Cleanups for C89 struct initializers and useless function
arguments"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/floppy: Use designated initializers
x86/mpx: Move bd_addr to mm_context_t
x86/mm: Drop unused argument 'removed' from sync_global_pgds()
ACPI/NUMA: Do not map pxm to node when NUMA is turned off
x86/acpi: Use proper macro for invalid node
x86/smpboot: Prevent false positive out of bounds cpumask access warning
x86/boot/64: Push correct start_cpu() return address
x86/boot/64: Use 'push' instead of 'call' in start_cpu()
x86/smpboot: Make logical package management more robust
-----BEGIN PGP SIGNATURE-----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=ADpU
-----END PGP SIGNATURE-----
Merge tag 'media/v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new Mediatek drivers: mtk-mdp and mtk-vcodec
- some additions at the media documentation
- the CEC core and drivers were promoted from staging to mainstream
- some cleanups at the DVB core
- the LIRC serial driver got promoted from staging to mainstream
- added a driver for Renesas R-Car FDP1 driver
- add DVBv5 statistics support to mn88473 driver
- several fixes related to printk continuation lines
- add support for HSV encoding formats
- lots of other cleanups, fixups and driver improvements.
* tag 'media/v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (496 commits)
[media] v4l: tvp5150: Add missing break in set control handler
[media] v4l: tvp5150: Don't inline the tvp5150_selmux() function
[media] v4l: tvp5150: Compile tvp5150_link_setup out if !CONFIG_MEDIA_CONTROLLER
[media] em28xx: don't store usb_device at struct em28xx
[media] em28xx: use usb_interface for dev_foo() calls
[media] em28xx: don't change the device's name
[media] mn88472: fix chip id check on probe
[media] mn88473: fix chip id check on probe
[media] lirc: fix error paths in lirc_cdev_add()
[media] s5p-mfc: Add support for MFC v8 available in Exynos 5433 SoCs
[media] s5p-mfc: Rework clock handling
[media] s5p-mfc: Don't keep clock prepared all the time
[media] s5p-mfc: Kill all IS_ERR_OR_NULL in clocks management code
[media] s5p-mfc: Remove dead conditional code
[media] s5p-mfc: Ensure that clock is disabled before turning power off
[media] s5p-mfc: Remove special clock rate management
[media] s5p-mfc: Use printk_ratelimited for reporting ioctl errors
[media] s5p-mfc: Set DMA_ATTR_ALLOC_SINGLE_PAGES
[media] vivid: Set color_enc on HSV formats
[media] v4l2-tpg: Init hv_enc field with a valid value
...
Driver updates for ARM SoCs, including a couple of newly added drivers:
- A new driver for the power management controller on TI Keystone
- Support for the prerelease "SCPI" firmware protocol that ended up
being shipped by Amlogic in their GXBB SoC.
- A soc_device can now be matched using a glob from inside the
kernel, when another driver wants to know the specific chip
it is running on and cannot find out from DT, firmware or hardware.
- Renesas SoCs now support identification through the soc_device
interface, both in user space and kernel.
- Renesas r8a7743 and r8a7745 gain support for their system controller
- A new checking module for the ARM "PSCI" (not to be confused
with "SCPI" mentioned above) firmware interface.
- A new driver for the Tegra GMI memory interface
- Support for the Tegra firmware interfaces with their
power management controllers
As usual, the updates for the reset controller framework are merged
here, as they tend to touch multiple SoCs as well, including a new
driver for the Oxford (now Broadcom) OX820 chip and the Tegra
bpmp interface.
The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
Rockchips SoCs see some further updates.
Conflicts:
- ARCH_RENESAS now selects SOC_BUS, but no longer needs GPIOLIB
- drivers/soc/renesas/Makefile: multiple files got added, keep
all in logical sorting
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6dP8
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- A new driver for the power management controller on TI Keystone
- Support for the prerelease "SCPI" firmware protocol that ended up
being shipped by Amlogic in their GXBB SoC.
- A soc_device can now be matched using a glob from inside the
kernel, when another driver wants to know the specific chip it is
running on and cannot find out from DT, firmware or hardware.
- Renesas SoCs now support identification through the soc_device
interface, both in user space and kernel.
- Renesas r8a7743 and r8a7745 gain support for their system
controller
- A new checking module for the ARM "PSCI" (not to be confused with
"SCPI" mentioned above) firmware interface.
- A new driver for the Tegra GMI memory interface
- Support for the Tegra firmware interfaces with their power
management controllers
As usual, the updates for the reset controller framework are merged
here, as they tend to touch multiple SoCs as well, including a new
driver for the Oxford (now Broadcom) OX820 chip and the Tegra bpmp
interface.
The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
Rockchips SoCs see some further updates"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (76 commits)
misc: sram: remove useless #ifdef
drivers: psci: Allow PSCI node to be disabled
drivers: psci: PSCI checker module
soc: renesas: Identify SoC and register with the SoC bus
firmware: qcom: scm: Return PTR_ERR when devm_clk_get fails
firmware: qcom: scm: Remove core, iface and bus clocks dependency
dt-bindings: firmware: scm: Add MSM8996 DT bindings
memory: da8xx-ddrctl: drop the call to of_flat_dt_get_machine_name()
bus: da8xx-mstpri: drop the call to of_flat_dt_get_machine_name()
ARM: shmobile: Document DT bindings for Product Register
soc: renesas: rcar-sysc: add R8A7745 support
reset: Add Tegra BPMP reset driver
dt-bindings: firmware: Allow child nodes inside the Tegra BPMP
dt-bindings: Add power domains to Tegra BPMP firmware
firmware: tegra: Add BPMP support
firmware: tegra: Add IVC library
dt-bindings: firmware: Add bindings for Tegra BPMP
mailbox: tegra-hsp: Use after free in tegra_hsp_remove_doorbells()
mailbox: Add Tegra HSP driver
firmware: arm_scpi: add support for pre-v1.0 SCPI compatible
...
A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost) fully
supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier LS1043A
with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above
chips, there are only a few consumer devices and boards added
this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral support
for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom, Rockchip, Berlin,
and ZTE.
Conflicts:
- Documentation/devicetree/bindings/arm/shmobile.txt: a
rename/add conflict, keep both modifications and maintain
alphabetical ordering.
- arch/arm64/boot/dts/*/*.dtsi: nodes were added in netdev,
mmc and clk, keep both sides in each case.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=geT0
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost)
fully supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier
LS1043A with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above chips,
there are only a few consumer devices and boards added this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral
support for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom,
Rockchip, Berlin, and ZTE"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (168 commits)
arm64: dts: fix build errors from missing dependencies
ARM64: dts: meson-gxbb: add SCPI pre-1.0 compatible
ARM64: dts: meson-gxl: Add support for Nexbox A95X
ARM64: dts: meson-gxm: Add support for the Nexbox A1
ARM: dts: artpec: add pcie support
arm64: dts: berlin4ct-dmp: add missing unit name to /memory node
arm64: dts: berlin4ct-stb: add missing unit name to /memory node
arm64: dts: berlin4ct: add missing unit name to /soc node
arm64: dts: qcom: msm8916: Add ddr support to sdhc1
arm64: dts: exynos: Enable HS400 mode for eMMC for TM2
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM64: dts: Add support for Meson GXM
dt-bindings: add rockchip RK1108 Evaluation board
arm64: dts: NS2: Add PCI PHYs
arm64: dts: NS2: enable sdio1
arm64: dts: exynos: Add the mshc_2 node for supporting T-Flash
arm64: tegra: Add NVIDIA P2771 board support
arm64: tegra: Enable PSCI on P3310
arm64: tegra: Add NVIDIA P3310 processor module support
arm64: tegra: Add GPIO controllers on Tegra186
...
Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where things
come together.
We get a DT descriptions for a couple of new SoCs, all of them variants
of other chips we already support, and usually coming with a new
evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers
or industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on
Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it into
products and have served their purpose in the kernel as a template
for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree
Conflicts:
arch/arm/boot/dts/r8a*.dtsi: a node was added
the clk tree, keep both sides and watch out for git
dropping the required '};' at the end of each side.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAWFMZHGCrR//JCVInAQKQ6A/+Og42qy1rhL3cfHiSsT7e5giQNVSFY7Cm
Z06R83AEv6HDMTNzyiJr5udRGOhm40qIoe92fhVJSRF7F6o/GbCQ7YOyU4KdQELg
caqRCe1Nq6RT0RYU0m6xVyv/ox0JTNEaB+TcvD1x4pgUQNo9sSBfiXpTzOKhLhqs
zmsfpNpj8v188Iofoju3WtwN26riJ7P4QdYIaNaH4qNQgoQbMbQICDwnpSsNJY+x
MSlNrbtYqfz6vc5fqa0mtfhF6wIFxuRnTgSLi9skWZ2l/fkn4ljF3RhN1Z86TYPv
CYsqDu+DF0YNxFrht3BAK6WTe2PdCnMNLNnMhYC6NDQ8YG1tbwvXQFM1KVanRvxx
hXP4Nt2sZYiqA4v8joFPgp9gnyBMdhtJEtWSmHwCY0RFObySJR4I1GY7igh02HUJ
gxlmOYcmklzLiyXvfjdDvg0sCV1tBhaBKTLYxF7lVCzG2QaR22Le+p3o+SWm+e+V
Ruc9l/iwHaeasNnbAkDEiEyi1FobtuEeTSZnKaXfKX8WuKVZLJrCEm7WiRIsj0Ww
vJ9ABVft7PEv/Ov3fbKBWON4vxKTBBgHuEDcbIsp19w4BSH1WJf5bGXIm7QeA3Z9
aD+DtA5W5ExIjMQR2+qgz/BBIzVVVVvG8DEcdcCtc3JGRJll5PadShLdqKjVIerc
SpsxqCKoRCI=
=wJt3
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
Changes to platform code for 64-bit ARM platforms. We are not adding
any new platforms that require code or Kconfig changes this time, so
it's basically just defconfig changes to enable support for more
drivers used on the existing platforms.
This is mainly interesting for the Raspberry Pi 3, which should
now work much better with the default build.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAWFLxS2CrR//JCVInAQJJDQ/9EVxolfQKMjld6M/ZpOaw1O/+rKUdFyUC
S6PIJgQD9/DIUVU+PMtHjljp+2GK0lJpLNXK3Tb4sJjx68ry9PSSHjZMEOJv33nE
mNsq3oQmbpPfZ6ufJrNqj1tS1ScxGDqudIx2L+DHwpg+lJjs984tKDQ4Ta18VI7m
k+a2IxoBWzGvzE50NFJppryZBq4p1WspfAkBLfohtTRGlCtmztbai6YZT0zfL1Iy
qdynNlh9yT5Y+JTTbnwPWJPH+YqsAMBeu/OqWyVfvpRc+fzPNIBNHrb5MfoWV6sP
JGyRUoQ0tDb0r+BTk68/5ALtKQQ40sxvPPpJgqRBy72gN5F4WhfIhfhP5zBMoyLU
X0pmPVB9CBFCz0BqUXcGofM/LvLLZeWOk+iAtl33AwmZ9U/e/e1Nobu9rqjv3hf1
nPqsDtisCo6RzDBfLCXX7XwX0GfRp3K81jWXIM7aULzhkrnFiPfz69qGFERLoTQf
w35n0YpT6yZDRsYYdTxprXD9y64fg4fKsp5XEQB6cE5Ea43AuH0WruxtazOGbJrz
nkatIO7dyK1/kl7fZZIxQiVY4F874j5X2bJPiCpB+vgDnkmPy8YV0PCfyRUA6jmK
sFsQFGTbqquXiKdtjwz+wrL0yRESgmCswaPBTiwD5cQC7s3GnCOkFsMvetuRLGk2
WSdHwEQ886k=
=B+Lz
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit updates from Arnd Bergmann:
"Changes to platform code for 64-bit ARM platforms. We are not adding
any new platforms that require code or Kconfig changes this time, so
it's basically just defconfig changes to enable support for more
drivers used on the existing platforms.
This is mainly interesting for the Raspberry Pi 3, which should now
work much better with the default build"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: defconfig: drop GPIO_SYSFS on multiplatforms
arm64: defconfig: Do not lower CONFIG_LOG_BUF_SHIFT
arm64: defconfig: allow rk3399-based boards to boot from mmc and usb
arm64: defconfig: enable RK808 components
arm64: defconfig: enable I2C and DW MMC controller on rockchip platform
arm64: defconfig: Enable Tegra186 SoC
ARM64: configs: Activate Internal PHY for Meson GXL
arm64: qcom: enable GPIOLIB in Kconfig
arm64: configs: enable configs for msm899(2/4) basic support
ARM64: bcm2835: add thermal driver to default config
ARM64: configs: Add Platform MHU in defconfig
MAINTAINERS: Update Broadcom Vulcan maintainer email
arm64: defconfig: enable EEPROM_AT25 config option
arm64: Enable HIBERNATION in defconfig
arm64: defconfig: Enable DRM DU and V4L2 FCP + VSP modules
ARM64: defconfig: Enable MMC related configs
arm64: Add BCM2835 (Raspberry Pi 3) support to the defconfig
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of
the machines that are still normally used with classic board files.
One tegra fix is important for new bootloader versions, but the
bug has been around for a while without anyone noticing.
The other changes are mostly cosmetic.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i2l2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of the
machines that are still normally used with classic board files. One
tegra fix is important for new bootloader versions, but the bug has
been around for a while without anyone noticing.
The other changes are mostly cosmetic"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
arm64: tegra: Add missing Smaug revision
arm64: tegra: Add VDD_GPU regulator to Jetson TX1
arm64: dts: zte: clean up gic-v3 redistributor properties
arm64: dts: zx: Fix gic GICR property
bus: vexpress-config: fix device reference leak
soc: ti: qmss: fix the case when !SMP
ARM: lpc32xx: drop duplicate header device.h
ARM: ixp4xx: drop duplicate header gpio.h
ARM: socfpga: fix spelling mistake in error message
ARM: dts: imx6q-cm-fx6: fix fec pinctrl
ARM: dts: imx7d-pinfunc: fix UART pinmux defines
ARM: dts: imx6qp: correct LDB clock inputs
ARM: OMAP2+: pm-debug: Use seq_putc() in two functions
ARM: OMAP2+: Remove the omapdss_early_init_of() function
mfd: tps65217: Fix mismatched interrupt number
ARM: zx: Fix error handling
ARM: spear: Fix error handling
ARM: davinci: da850: Fix pwm name matching
ARM: clk: imx31: properly init clocks for machines with DT
clk: imx31: fix rewritten input argument of mx31_clocks_init()
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ut0k
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes:
- add support for PCI on ARM64 boxes with ACPI. We already had this
for theoretical spec-compliant hardware; now we're adding quirks
for the actual hardware (Cavium, HiSilicon, Qualcomm, X-Gene)
- add runtime PM support for hotplug ports
- enable runtime suspend for Intel UHCI that uses platform-specific
wakeup signaling
- add yet another host bridge registration interface. We hope this is
extensible enough to subsume the others
- expose device revision in sysfs for DRM
- to avoid device conflicts, make sure any VF BAR updates are done
before enabling the VF
- avoid unnecessary link retrains for ASPM
- allow INTx masking on Mellanox devices that support it
- allow access to non-standard VPD for Chelsio devices
- update Broadcom iProc support for PAXB v2, PAXC v2, inbound DMA,
etc
- update Rockchip support for max-link-speed
- add NVIDIA Tegra210 support
- add Layerscape LS1046a support
- update R-Car compatibility strings
- add Qualcomm MSM8996 support
- remove some uninformative bootup messages"
* tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (115 commits)
PCI: Enable access to non-standard VPD for Chelsio devices (cxgb3)
PCI: Expand "VPD access disabled" quirk message
PCI: pciehp: Remove loading message
PCI: hotplug: Remove hotplug core message
PCI: Remove service driver load/unload messages
PCI/AER: Log AER IRQ when claiming Root Port
PCI/AER: Log errors with PCI device, not PCIe service device
PCI/AER: Remove unused version macros
PCI/PME: Log PME IRQ when claiming Root Port
PCI/PME: Drop unused support for PMEs from Root Complex Event Collectors
PCI: Move config space size macros to pci_regs.h
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI/ASPM: Don't retrain link if ASPM not possible
PCI: iproc: Skip check for legacy IRQ on PAXC buses
PCI: pciehp: Leave power indicator on when enabling already-enabled slot
PCI: pciehp: Prioritize data-link event over presence detect
PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar
PCI: rcar: Use gen2 fallback compatibility last
PCI: rcar-gen2: Use gen2 fallback compatibility last
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
..
These changes include:
* Support for the ACPI IORT table on ARM systems and patches to
make the ARM-SMMU driver make use of it
* Conversion of the Exynos IOMMU driver to device dependency
links and implementation of runtime pm support based on that
conversion
* Update the Mediatek IOMMU driver to use the new
struct device->iommu_fwspec member
* Implementation of dma_map/unmap_resource in the generic ARM
dma-iommu layer
* A number of smaller fixes and improvements all over the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=EYLL
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"These changes include:
- support for the ACPI IORT table on ARM systems and patches to make
the ARM-SMMU driver make use of it
- conversion of the Exynos IOMMU driver to device dependency links
and implementation of runtime pm support based on that conversion
- update the Mediatek IOMMU driver to use the new struct
device->iommu_fwspec member
- implementation of dma_map/unmap_resource in the generic ARM
dma-iommu layer
- a number of smaller fixes and improvements all over the place"
* tag 'iommu-updates-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (44 commits)
ACPI/IORT: Make dma masks set-up IORT specific
iommu/amd: Missing error code in amd_iommu_init_device()
iommu/s390: Drop duplicate header pci.h
ACPI/IORT: Introduce iort_iommu_configure
ACPI/IORT: Add single mapping function
ACPI/IORT: Replace rid map type with type mask
iommu/arm-smmu: Add IORT configuration
iommu/arm-smmu: Split probe functions into DT/generic portions
iommu/arm-smmu-v3: Add IORT configuration
iommu/arm-smmu-v3: Split probe functions into DT/generic portions
ACPI/IORT: Add support for ARM SMMU platform devices creation
ACPI/IORT: Add node match function
ACPI: Implement acpi_dma_configure
iommu/arm-smmu-v3: Convert struct device of_node to fwnode usage
iommu/arm-smmu: Convert struct device of_node to fwnode usage
iommu: Make of_iommu_set/get_ops() DT agnostic
ACPI/IORT: Add support for IOMMU fwnode registration
ACPI/IORT: Introduce linker section for IORT entries probing
ACPI: Add FWNODE_ACPI_STATIC fwnode type
iommu/arm-smmu: Set SMTNMB_TLBEN in ACR to enable caching of bypass entries
...
* patchwork: (496 commits)
[media] v4l: tvp5150: Add missing break in set control handler
[media] v4l: tvp5150: Don't inline the tvp5150_selmux() function
[media] v4l: tvp5150: Compile tvp5150_link_setup out if !CONFIG_MEDIA_CONTROLLER
[media] em28xx: don't store usb_device at struct em28xx
[media] em28xx: use usb_interface for dev_foo() calls
[media] em28xx: don't change the device's name
[media] mn88472: fix chip id check on probe
[media] mn88473: fix chip id check on probe
[media] lirc: fix error paths in lirc_cdev_add()
[media] s5p-mfc: Add support for MFC v8 available in Exynos 5433 SoCs
[media] s5p-mfc: Rework clock handling
[media] s5p-mfc: Don't keep clock prepared all the time
[media] s5p-mfc: Kill all IS_ERR_OR_NULL in clocks management code
[media] s5p-mfc: Remove dead conditional code
[media] s5p-mfc: Ensure that clock is disabled before turning power off
[media] s5p-mfc: Remove special clock rate management
[media] s5p-mfc: Use printk_ratelimited for reporting ioctl errors
[media] s5p-mfc: Set DMA_ATTR_ALLOC_SINGLE_PAGES
[media] vivid: Set color_enc on HSV formats
[media] v4l2-tpg: Init hv_enc field with a valid value
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.10:
API:
- add skcipher walk interface
- add asynchronous compression (acomp) interface
- fix algif_aed AIO handling of zero buffer
Algorithms:
- fix unaligned access in poly1305
- fix DRBG output to large buffers
Drivers:
- add support for iMX6UL to caam
- fix givenc descriptors (used by IPsec) in caam
- accelerated SHA256/SHA512 for ARM64 from OpenSSL
- add SSE CRCT10DIF and CRC32 to ARM/ARM64
- add AEAD support to Chelsio chcr
- add Armada 8K support to omap-rng"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (148 commits)
crypto: testmgr - fix overlap in chunked tests again
crypto: arm/crc32 - accelerated support based on x86 SSE implementation
crypto: arm64/crc32 - accelerated support based on x86 SSE implementation
crypto: arm/crct10dif - port x86 SSE implementation to ARM
crypto: arm64/crct10dif - port x86 SSE implementation to arm64
crypto: testmgr - add/enhance test cases for CRC-T10DIF
crypto: testmgr - avoid overlap in chunked tests
crypto: chcr - checking for IS_ERR() instead of NULL
crypto: caam - check caam_emi_slow instead of re-lookup platform
crypto: algif_aead - fix AIO handling of zero buffer
crypto: aes-ce - Make aes_simd_algs static
crypto: algif_skcipher - set error code when kcalloc fails
crypto: caam - make aamalg_desc a proper module
crypto: caam - pass key buffers with typesafe pointers
crypto: arm64/aes-ce-ccm - Fix AEAD decryption length
MAINTAINERS: add crypto headers to crypto entry
crypt: doc - remove misleading mention of async API
crypto: doc - fix header file name
crypto: api - fix comment typo
crypto: skcipher - Add separate walker for AEAD decryption
..
