Some devices can't mask/unmask the data ready pin and in those cases
each driver was just calling '{dis}enable_irq()' to control the trigger
state. This change, moves that handling into the library by introducing
a new boolean in the data structure that tells the library that the
device cannot unmask the pin.
On top of controlling the trigger state, we can also use this flag to
automatically request the IRQ with 'IRQF_NO_AUTOEN' in case it is set.
So far, all users of the library want to start operation with IRQs/DRDY
pin disabled so it should be fairly safe to do this inside the library.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210903141423.517028-3-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Typically, in burst mode, the device cannot operate at it's full spi
speed. Hence, the spi transfers for burst mode have to take this into
account. With this change we avoid a potential race with the spi core as
drivers were 'hacking' the device 'max_speed_hz' directly in the
trigger handler.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210427085454.30616-5-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add some helpers to lock and unlock the device. As this is such a simple
change, we update all the users that were using the lock already in this
patch.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210218114039.216091-5-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add burst mode variables in the per device specific data structure. As
some drivers support multiple devices with different burst sizes it
makes sense this data to be in `adis_data`. While moving the variables,
there are two main differences:
1. The `en`variable is dropped. If a device supports burst mode, it will
just use it as it will has better performance for almost all real use
cases.
2. Replace `extra_len` by `burst_len`. Users should now explicitly
define the length of the burst buffer as it is typically constant. This
also allows to remove the following line from the library:
```
/* All but the timestamp channel */
burst_length = (indio_dev->num_channels - 1) * sizeof(u16);
```
The library should not assume that a timestamp channel is defined.
Moreover, most parts also include some diagnostic data, crc, etc.. in
the burst buffer that needed to be included in an `extra_len` variable
which is not that nice. On top of this, some devices already start to
have some 32bit size channels ...
This patch is also a move to completely drop the `struct adis_burst`
from the library.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20200917155223.218500-2-nuno.sa@analog.com
Drop `adis_setup_buffer_and_trigger()`. All users were updated to use
the devm version of this function. This avoids having almost the same
code repeated.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20200915120258.161587-11-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add burst_max_len to `adis_burst`. This is useful for devices which
support different burst modes with different sizes. The buffer to be
used in the spi transfer is allocated with this variable making sure
that has space for all burst modes. The spi transfer length should hold
the "real" burst length depending on the current burst mode configured
in the device.
Moreover, `extra_len` in `adis_burst` is made const and it should
contain the smallest extra length necessary for a burst transfer. In
`struct adis` was added a new `burst_extra_len` that should hold the
extra bytes needed depending on the device instance being used.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds a `regmap_update_bits()` like API to the ADIS library.
It provides locked and unlocked variant.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are some ADIS devices that can configure the data ready pin
polarity. Hence, we cannot hardcode our IRQ mask as IRQF_TRIGGER_RISING
since we might want to have it as IRQF_TRIGGER_FALLING.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for a managed device version of
adis_setup_buffer_and_trigger. It works exactly as the original
one but it calls all the devm_iio_* functions to setup an iio
buffer and trigger. Hence we do not need to care about cleaning those
and we do not need to support a remove() callback for every driver using
the adis library.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The 'state_lock' mutex was renamed from 'txrx_lock' in a previous patch and
is intended to be used by ADIS drivers to protect the state of devices
during consecutive R/W ops.
The initial patch that introduced this change did not do a good [well, any]
job at explaining this. This patch adds a comment to the 'state_lock'
better explaining it's use.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The doc-string has been neglected over time.
This change updates it with all the missing info.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change adds a doc-string for the 'adis' struct. It details the fields
and their roles.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Each driver/chip that wants to validate it's product id, can now
specify a 'prod_id_reg' and an expected 'prod_id' value.
The 'prod_id' value is intentionally left 0 (uninitialized). There aren't
(yet) any product IDs with value 0; this enforces that both 'prod_id_reg'
and 'prod_id' are specified.
At the very least, this routine validates that the SPI connection to the
ADIS chip[s] works well.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds a dedicated self_test_reg variable. This is also a step
to let new drivers make use of `adis_initial_startup()`. Some devices
use MSG_CTRL reg to request a self_test command while others use the
GLOB_CMD register.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change splits the __adis_initial_startup() away from
adis_initial_startup(). The unlocked version can be used in certain calls
during probe, where races won't happen since the ADIS driver may not be
registered yet with IIO.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All timeouts are now handled by a dedicated timeout struct. This
variable is no longer needed.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The adis library only allows to define a `startup_delay` which for some
devices is enough. However, other devices define different timeouts with
significantly different timings which could lead to devices to not wait
enough time or to wait a lot more than necessary (which is not
efficient). This patch introduces a new timeout struct that must be
passed into `adis_init()`. There are mainly, for now, three timeouts
used. This is also an introductory patch with the goal of refactoring
`adis_initial_startup()`. New driver's (eg: adis16480, adis16460) are
replicating code for the device initial setup. With some changes (being
this the first one) we can pass this to `adis_initial_startup()`.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The reset routine may also be important to be protected by the state-lock
and grouped with other operations, so create an unlocked version, so that
this can be done.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This one also gets re-used in certain operations, so it makes sense to
have an unlocked version of this to group it with other
reads/writes/operations to have a single lock for the whole state change.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This will allow more flexible control to group reads & writes into a single
lock (particularly the state_lock).
The end-goal is to remove the indio_dev->mlock usage, and the simplest fix
would have been to just add another lock, which would not be a good idea on
the long-run.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The lock can be extended a bit to protect other elements that are not
particular to just TX/RX. Another idea would have been to just add a new
`state_lock`, but that would mean 2 locks which would be redundant, and
probably cause more potential for dead-locks.
What will be done in the next patches, will be to add some unlocked
versions for read/write_reg functions.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The inline read functions in the ADIS library don't check the return value
of the `adis_read_reg()` function and assign the value of `tmp` regardless.
Fix this by checking if return value is zero and only then assigning the
value of `tmp`.
No known case of the callers of this function incorrectly using the
value, but best to stop any potential risk here.
Not suitable for stable due to no known actual bugs caused by this
issue.
Fixes: 57a1228a06 ("iio:imu:adis: Add support for 32bit registers")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS16460 requires a higher delay before the next transfer. Since the
SPI framework supports configuring the delay before the next transfer, this
driver will become the first user of it.
The support for this functionality in ADIS16460 requires an addition to the
ADIS lib to support the `cs_change_delay` functionality from the SPI
subsystem.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Based on 1 normalized pattern(s):
licensed under the gpl 2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 82 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190524100845.150836982@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some variants in the ADIS16400 family support burst mode. This mechanism is
implemented in the `adis16400_buffer.c` file.
Some variants in ADIS16480 are also adding burst mode, which is
functionally similar to ADIS16400, but with different parameters. To get
there, a `adis_burst` struct is added to parametrize certain bits of the
SPI communication to setup: the register that triggers burst-mode, and the
extra-data-length that needs be accounted for when building the bust-length
buffer.
The trigger handler cannot be made generic, since it's very specific to
each ADIS164XX family.
A future enhancement of this `adis_burst` mode will be the possibility to
enable/disable burst-mode. For the ADIS16400 family it's hard-coded to on
by default. But for ADIS16480 there will be a need to disable this.
When that will be implemented, both ADIS16400 & ADIS16480 will have the
burst-mode enable-able/disable-able.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some variants of the devices from the ADIS family don't auto-clear the
self-test bit after the self-test has completed. Instead we have to
manually clear. Add support for this to the ADIS library.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
By using the info_mask_shared_by_all element of the channel spec, acce
to the sampling frequency becomes available to in kernel users of the
driver. It also shortens and simplifies the code.
This particular conversion was made more complicated by the shared library
and the fact that a number of the drivers do not actually have support for
setting or reading the sampling frequency. The hardware, in those cases
investigated supports it. It's just never been implemented.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
This patch adds support for the ADIS16375, ADIS16480, ADIS16485, ADIS16488 6
degree to 10 degree of freedom IMUs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some of the newer generation devices from the ADIS16XXX series have more
registers than what can be supported with the current register addressing
scheme. These devices implement register paging to support a larger register
range. Each page is 128 registers large and the currently active page can be
selected via register 0x00 in each page. This patch implements transparent
paging inside the common adis library. The register read/write interface stays
the same and when a register is accessed the library automatically switches to
the correct page if it is not already selected. The page number is encoded in
the upper bits of the register number, e.g. register 0x5 of page 1 is 0x85.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some of the newer generation devices from the ADIS16XXX family have 32bit wide
register which spans two 16bit wide registers. This patch adds support for
reading and writing a 32bit wide register.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Provide a IIO debugfs register access function for the ADIS library. This
function can be used by individual drivers to allow raw register access via
debugfs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Now that the adis library no longer depends on the sw_ring buffer implementation
we can move it out of staging.
While we are at it also sort the entries in the iio Kconfig and Makefile to be
in alphabetical order.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
