The call to gpiod_set_value_cansleep() in cs42l42_sdw_update_status()
needs the header file gpio/consumer.h to be included.
This was introduced by commit 2d066c6a78 ("ASoC: cs42l42: Avoid stale
SoundWire ATTACH after hard reset")
and caused error:
sound/soc/codecs/cs42l42-sdw.c:374:4: error: implicit declaration of
function ‘gpiod_set_value_cansleep’;
did you mean gpio_set_value_cansleep’?
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2d066c6a78 ("ASoC: cs42l42: Avoid stale SoundWire ATTACH after hard reset")
Link: https://lore.kernel.org/r/20231011134853.20059-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to an error in the datasheet the bias sense values currently don't
match the hardware. Whilst this is a change to the binding no devices
have yet shipped so updating the binding will not cause any issues.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231010102425.3662364-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASP1 DOUT line must be defaulted to be high-impedance when
it is not actually transmitting data for an active channel.
In non-SoundWire modes ASP1 will usually be shared by multiple
amps so each amp must only drive the line during the slot for
an enabled TX channel.
In SoundWire mode a custom firmware can use ASP1 as a secondary
chip-to-chip audio link or as GPIO. It should be defaulted to
high-impedance since by default the purpose of this pin is not
known.
Backport note:
On kernel versions before 6.6 the cs35l56->base.regmap argument
to regmap_set_bits() must be changed to cs35l56->regmap.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e496112529 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://lore.kernel.org/r/20231009153412.30380-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>:
Some codec drivers compare widget names with strcmp, ignoring the component
name prefix. If prefix is used, the comparisons start failing.
Add a helper to fix the issue.
Merge series from Johan Hovold <johan+linaro@kernel.org>:
The wcd938x codec driver happily ignores error handling, something which
has bitten us in the past when we hit a probe deferral:
https://lore.kernel.org/lkml/20230705123018.30903-1-johan+linaro@kernel.org/
Fix up the remaining probe and component bind paths that left resources
allocated and registered after errors to avoid similar future issues.
Fix cs35l56_patch() to call reinit_completion() to reinitialize
the completion object.
It was incorrectly using init_completion().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e496112529 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://lore.kernel.org/r/20231006164405.253796-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to balance the runtime PM operations, including the disable
count, on probe errors and on driver unbind.
Fixes: 16572522ae ("ASoC: codecs: wcd938x-sdw: add SoundWire driver")
Cc: stable@vger.kernel.org # 5.14
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231003155558.27079-8-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to deregister the component when the driver is being unbound
and before the underlying device-managed resources are freed.
Fixes: 16572522ae ("ASoC: codecs: wcd938x-sdw: add SoundWire driver")
Cc: stable@vger.kernel.org # 5.14
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231003155558.27079-7-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to balance the runtime PM operations, including the disable
count, on driver unbind.
Fixes: 16572522ae ("ASoC: codecs: wcd938x-sdw: add SoundWire driver")
Cc: stable@vger.kernel.org # 5.14
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231003155558.27079-6-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to disable and free the regulators on probe errors and on
driver unbind.
Fixes: 16572522ae ("ASoC: codecs: wcd938x-sdw: add SoundWire driver")
Cc: stable@vger.kernel.org # 5.14
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231003155558.27079-5-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing code to release resources on bind errors, including the
references taken by wcd938x_sdw_device_get() which also need to be
dropped on unbind().
Fixes: 16572522ae ("ASoC: codecs: wcd938x-sdw: add SoundWire driver")
Cc: stable@vger.kernel.org # 5.14
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231003155558.27079-4-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to deregister the component before tearing down the resources
it depends on during unbind().
Fixes: 16572522ae ("ASoC: codecs: wcd938x-sdw: add SoundWire driver")
Cc: stable@vger.kernel.org # 5.14
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231003155558.27079-3-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop the bogus error handling for a soundwire device backcast during
bind() that cannot fail.
Fixes: 16572522ae ("ASoC: codecs: wcd938x-sdw: add SoundWire driver")
Cc: stable@vger.kernel.org # 5.14
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231003155558.27079-2-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When comparing widget names in wsa_macro_spk_boost_event(), consider
also the component's name prefix. Otherwise the WSA codec won't have
proper mixer setup resulting in no sound playback through speakers.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231003155710.821315-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Some drivers use one event callback for multiple widgets but still need
to perform a bit different actions based on actual widget. This is done
by comparing widget name, however drivers tend to miss possible name
prefix. Add a helper to solve common mistakes.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231003155710.821315-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Like the Lenovo 82TL, 82V2, 82QF and 82UG, the 82YM (Yoga 7 14ARP8)
requires an entry in the quirk list to enable the internal microphone.
The latter two received similar fixes in commit 1263cc0f41
("ASoC: amd: yc: Fix non-functional mic on Lenovo 82QF and 82UG").
Fixes: c008323fe3 ("ASoC: amd: yc: Fix a non-functional mic on Lenovo 82SJ")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Frotscher <sven.frotscher@gmail.com>
Link: https://lore.kernel.org/r/20230927223758.18870-1-sven.frotscher@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The micbias setting for tlv320adc can also have the value '3' which
means that the micbias ouput pin is connected to the input pin AVDD.
Signed-off-by: Antoine Gennart <gennartan@disroot.org>
Link: https://lore.kernel.org/r/20230929130117.77661-1-gennartan@disroot.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This will attempt to disable the regulators if the initial enable fails
which is a bug.
Fix this bug by modifying the code to the correct sequence.
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Link: https://lore.kernel.org/r/tencent_4F37C9B5315B7960041E8E0ADDA869128F08@qq.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 4e08713336 ("ASoC: hdmi-codec: fix channel info for
compressed formats") accidentally changed hcp->chmap_idx from
ca_id, the CEA channel allocation ID, to idx, the index to
the table of channel mappings ordered by preference.
This resulted in wrong channel maps being reported to userspace,
eg for 5.1 "FL,FR,LFE,FC" was reported instead of the expected
"FL,FR,LFE,FC,RL,RR":
~ # speaker-test -c 6 -t sine
...
0 - Front Left
3 - Front Center
1 - Front Right
2 - LFE
4 - Unknown
5 - Unknown
~ # amixer cget iface=PCM,name='Playback Channel Map' | grep ': values'
: values=3,4,8,7,0,0,0,0
Switch this back to ca_id in case of PCM audio so the correct channel
map is reported again and set it to HDMI_CODEC_CHMAP_IDX_UNKNOWN in
case of non-PCM audio so the PCM channel map control returns "Unknown"
channels (value 0).
Fixes: 4e08713336 ("ASoC: hdmi-codec: fix channel info for compressed formats")
Cc: stable@vger.kernel.org
Signed-off-by: Matthias Reichl <hias@horus.com>
Link: https://lore.kernel.org/r/20230929195027.97136-1-hias@horus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On init we have sequence:
for_each_card_prelinks(card, i, dai_link) {
ret = snd_soc_add_pcm_runtime(card, dai_link);
ret = init_some_other_things(...);
if (ret)
goto probe_end:
for_each_card_rtds(card, rtd) {
ret = soc_init_pcm_runtime(card, rtd);
probe_end:
while on exit:
for_each_card_rtds(card, rtd)
snd_soc_link_exit(rtd);
If init_some_other_things() step fails due to error we end up with
not fully setup rtds and try to call snd_soc_link_exit on them, which
depending on contents on .link_exit handler, can end up dereferencing
NULL pointer.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230929103243.705433-2-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When printing log related to component it is useful to know, to which
component it applies to.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230929103243.705433-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting ACP ACLK as clock source when ACP enters D0 state causing
firmware load failure as mentioned in below scenario.
- Load snd_sof_amd_rembrandt
- Play or Record audio
- Stop audio
- Unload snd_sof_amd_rembrandt
- Reload snd_sof_amd_rembrandt
If acp_clkmux_sel register field is set, then clock source will be
set to ACP ACLK when ACP enters D0 state.
During stream stop, if there is no active stream is running then
acp firmware will set the ACP ACLK value to zero.
When driver is reloaded and clock source is selected as ACP ACLK,
as ACP ACLK is programmed to zero, firmware loading will fail.
For RMB platform, remove the clock mux selection field so that
ACP will use internal clock source when ACP enters D0 state.
Fixes: 41cb85bc4b ("ASoC: SOF: amd: Add support for Rembrandt plaform.")
Reported-by: coolstar <coolstarorganization@gmail.com>
Closes: https://github.com/thesofproject/sof/issues/8137
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230927071412.2416250-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As the pll_id and pll_id can be zero (WM8960_SYSCLK_AUTO)
with the commit 2bbc2df46e ("ASoC: wm8960: Make automatic the
default clocking mode")
Then the machine driver will skip to call set_sysclk() and set_pll()
for codec, when the sysclk rate is different with what wm8960 read
at probe, the output sound frequency is wrong.
So change the fll_id and pll_id initial value, still keep machine
driver's behavior same as before.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1695202992-24864-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On i.MX8MP, the BCE and TERE bit are binding with mclk
enablement, if BCE and TERE are cleared the MCLK also be
disabled on output pin, that cause the external codec (wm8960)
in wrong state.
Codec (wm8960) is using the mclk to generate PLL clock,
if mclk is disabled before disabling PLL, the codec (wm8960)
won't generate bclk and frameclk when sysclk switch to
MCLK source in next test case.
The test case:
$aplay -r44100 test1.wav (PLL source)
$aplay -r48000 test2.wav (MCLK source)
aplay: pcm_write:2127: write error: Input/output error
Fixes: 269f399dc1 ("ASoC: fsl_sai: Disable bit clock with transmitter")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1695116533-23287-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
While browsing/grepping in the sound core, I found that
snd_dmaengine_set_config_from_dai_data() did not exist, in favor of
snd_dmaengine_pcm_set_config_from_dai_data(). Fix the typo.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230922161547.594484-1-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
asoc_simple_probe() is used for both "DT probe" (A) and "platform probe"
(B). It uses "goto err" when error case, but it is not needed for
"platform probe" case (B). Thus it is using "return" directly there.
static int asoc_simple_probe(...)
{
^ if (...) {
| ...
(A) if (ret < 0)
| goto err;
v } else {
^ ...
| if (ret < 0)
(B) return -Exxx;
v }
...
^ if (ret < 0)
(C) goto err;
v ...
err:
(D) simple_util_clean_reference(card);
return ret;
}
Both case are using (C) part, and it calls (D) when err case.
But (D) will do nothing for (B) case.
Because of these behavior, current code itself is not wrong,
but is confusable, and more, static analyzing tool will warning on
(B) part (should use goto err).
To avoid static analyzing tool warning, this patch uses "goto err"
on (B) part.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o7hy7mlh.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The rule for the SoundWire tables is that the platforms with more
devices need to be added first. We broke that rule with the Dell SKU
0B34, and caused the second amplifier for SKU 0AF3 to be ignored.
The fix is simple, we need to move the single-amplifier entry after
the two-amplifier one.
Fixes: b62a1a839b ("ASoC: Intel: soc-acpi: add tables for Dell SKU 0B34")
Closes: https://github.com/thesofproject/linux/issues/4559
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919083606.1920202-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding HDMI-In capture via I2S feature support in MTL platform.
Signed-off-by: Balamurugan C <balamurugan.c@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919091136.1922253-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding support for ES83x6 codec in MTL match table.
Signed-off-by: Balamurugan C <balamurugan.c@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919091136.1922253-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All the fail paths during probe will free up the ops, on remove we should
only free it if the probe was successful.
Fixes: bc433fd76f ("ASoC: SOF: Add ops_free")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20230915124015.19637-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
20s seems unnecessarily large for the DSP init timeout. This coupled with
multiple FW boot attempts causes an excessive delay in the error path when
booting in recovery mode. Reduce it to 0.5s and use the existing
HDA_DSP_INIT_TIMEOUT_US.
Link: https://github.com/thesofproject/linux/issues/4565
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230915134153.9688-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The microphone and speaker shutters on cs42l43 can be configured to
trigger from the same GPIO, in this case the current code returns an
error as we attempt to request two IRQ handlers for the same IRQ. Fix
this by always requesting the shutter IRQs with the IRQF_SHARED flag.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230915144300.120100-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The devm_clk_get() can return -EPROBE_DEFER error,
modify the error code to be -EINVAL is not correct, which
cause the -EPROBE_DEFER error is not correctly handled.
This patch is to fix the return error code.
Fixes: b86ef53677 ("ASoC: fsl: Add Audio Mixer machine driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/1694757731-18308-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Because of the potential failure of the devm_kstrdup(), the
dl[i].codecs->name could be NULL.
Therefore, we need to check it and return -ENOMEM in order to transfer
the error.
Fixes: 97030a4337 ("ASoC: Intel: avs: Add HDAudio machine board")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230915021344.3078-1-nichen@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
In case the widget setup fails we should only decrement the core usage
count if the sof_widget_free_unlocked() has not been called as part of
the error handling.
sof_widget_free_unlocked() calls snd_sof_dsp_core_put() and the additional
core_put will cause imbalance in core usage count.
Use the existing use_count_decremented to handle this issue.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230914124725.17397-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
available_fmt is a pointer.
Fixes: 4fdef47a44 ("ASoC: SOF: ipc4-topology: Add new tokens for input/output pin format count")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230914132504.18463-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
i.MX rpmsg sound cards work on codec slave mode. MCLK will be disabled
by CPU DAI driver in hw_free(). Some codec requires MCLK present at
power up/down sequence. So need to set ignore_pmdown_time to power down
codec immediately before MCLK is turned off.
Take WM8962 as an example, if MCLK is disabled before DAPM power down
playback stream, FIFO error will arise in WM8962 which will have bad
impact on playback next.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230913102656.2966757-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Stefan Binding <sbinding@opensource.cirrus.com>:
These patches fix 3 problems with hard reset:
1. Ensure a minimum reset pulse width
2. Deal with ACPI overriding the requested default GPIO state
3. Avoid a race condition when hard-resetting a SoundWire peripheral
that is already enumerated
wm_adsp_read_ctl() and wm_adsp_write_ctl() must hold the cs_dsp pwr_lock
mutex when calling cs_dsp_coeff_read_ctrl() and cs_dsp_coeff_write_ctrl().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913160250.3700346-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In SoundWire mode leave hard RESET asserted when exiting probe,
and wait for an UNATTACHED notification before deasserting RESET.
If the boot state of the reset GPIO was deasserted it is possible
that the SoundWire core had already enumerated the CS42L42 before
cs42l42_sdw_probe() is called. When cs42l42_common_probe() hard
resets the CS42L42 it triggers a race condition:
1) After cs42l42_sdw_probe() returns the thread that called it
will call cs42l42_sdw_update_status() to report the last
status recorded by the SoundWire core.
2) The SoundWire bus master will see a PING with the CS42L42
now reporting as unenumerated and will trigger the core
SoundWire code to start enumerating CS42L42.
These two threads are racing against each other. If (1)
happens before (2) a stale ATTACHED notification will be
reported to the cs42l42 driver when in fact the status of
cs42l42 is now unattached.
To avoid this race condition:
- Leave RESET asserted on exit from cs42l42_sdw_probe().
This ensures that an UNATTACHED notification must be
sent to the cs42l42 driver. If cs42l42 was already
enumerated it will be seen to drop off the bus, causing
an UNATTACH notification. If it was never enumerated the
status is already UNATTACHED and this will be reported
by thread (1).
- When the UNATTACH notification is received, release RESET.
This will cause CS42L42 to be enumerated and eventually
report an ATTACHED notification.
- The ATTACHED notification is now valid.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-4-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ACPI setting for a GPIO default state has higher priority than the
flag passed to devm_gpiod_get_optional() so ACPI can override the
GPIOD_OUT_LOW. Explicitly set the GPIO low when hard resetting.
Although GPIOD_OUT_LOW can't be relied on this doesn't seem like a
reason to stop passing it to devm_gpiod_get_optional(). So we still pass
it to state our intent, but can deal with it having no effect.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-3-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS42L42 can accept very short reset pulses of a few microseconds
but there's no reason to force a very short pulse.
Allow a wide range for the usleep_range() so it can be relaxed about
the choice of timing source.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-2-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Hans de Goede <hdegoede@redhat.com>:
The recent(ish) rt5640 changes to add HDA header jack-detect support
and the related suspend/resume handling fixes have introduced several
issues with IRQ handling on boards not using the HDA header jack-detect
support.
This series fixes these issues, see the individual commit messages
for details.
Do not allow the CS35L56 to be put into its lowest power
"hibernation" mode. This only affects I2C because "hibernation"
is already disabled on SPI and SoundWire.
Recent firmwares need a different wake-up sequence. Until
that sequence has been specified, the chip "hibernation" mode
must be disabled otherwise it can intermittently fail to wake.
THIS WILL NOT APPLY CLEANLY TO 6.5 AND EARLIER:
We will send a separate backport patch to stable.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230912133841.3480466-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If jack-detection is not used; or has already been disabled then
there is no need to call rt5640_cancel_work().
Move the rt5640_cancel_work() inside the "if (rt5640->jack) {}" block,
grouping it together with the disabling of the IRQ which queues the work
in the first place.
This also makes suspend() symetrical with resume() which re-queues the work
in an "if (rt5640->jack) {}" block.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-7-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Set "rt5640->irq_requested = true" after a successful request_irq()
in rt5640_enable_hda_jack_detect(), so that rt5640_disable_jack_detect()
properly frees the IRQ.
This fixes the IRQ not being freed on rmmod / driver unbind.
Fixes: 2b9c8d2b3c ("ASoC: rt5640: Add the HDA header support")
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-6-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The jack-detect IRQ should be enabled *after* the jack-detect related
configuration registers have been programmed.
Move the enable_irq() call for this to after the register setup.
Fixes: 5fabcc90e7 ("ASoC: rt5640: Fix Jack work after system suspend")
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-5-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When jack-detect was originally added disabling the IRQ during suspend
was done by the sound/soc/intel/boards/bytcr_rt5640.c driver
calling snd_soc_component_set_jack(NULL) on suspend, which calls
rt5640_disable_jack_detect(), which calls free_irq() which also
disables it.
Commit 5fabcc90e7 ("ASoC: rt5640: Fix Jack work after system suspend")
added disable_irq() / enable_irq() calls on suspend/resume for machine
drivers which do not call snd_soc_component_set_jack(NULL) on suspend.
The new disable_irq() / enable_irq() are made conditional by
"if (rt5640->irq)" statements, but this is true for the machine drivers
which do call snd_soc_component_set_jack(NULL) on suspend too, causing
a disable_irq() call there on the already free-ed IRQ.
Change the "if (rt5640->irq)" condition to "if (rt5640->jack)" to fix this,
rt5640->jack is only set if the jack-detect IRQ handler is still active
when rt5640_suspend() runs.
And adjust rt5640_enable_hda_jack_detect()'s request_irq() error handling
to set rt5640->jack to NULL to match (note that the old setting of irq to
-ENOXIO still resulted in disable_irq(-ENOXIO) calls on suspend).
Fixes: 5fabcc90e7 ("ASoC: rt5640: Fix Jack work after system suspend")
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-4-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Following prints are observed while testing audio on Jetson AGX Orin which
has onboard RT5640 audio codec:
BUG: sleeping function called from invalid context at kernel/workqueue.c:3027
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 0, name: swapper/0
preempt_count: 10001, expected: 0
RCU nest depth: 0, expected: 0
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:159 __handle_irq_event_percpu+0x1e0/0x270
---[ end trace ad1c64905aac14a6 ]-
The IRQ handler rt5640_irq() runs in interrupt context and can sleep
during cancel_delayed_work_sync().
The only thing which rt5640_irq() does is cancel + (re-)queue
the jack_work delayed_work. This can be done in a single non sleeping
call by replacing queue_delayed_work() with mod_delayed_work(),
avoiding the sleep in atomic context.
Fixes: 051dade346 ("ASoC: rt5640: Fix the wrong state of JD1 and JD2")
Reported-by: Sameer Pujar <spujar@nvidia.com>
Closes: https://lore.kernel.org/r/1688015537-31682-4-git-send-email-spujar@nvidia.com
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 70a6404ff6 ("ASoC: rt5640: Fix sleep in atomic context")
not only switched from request_irq() to request_threaded_irq(),
to fix the sleep in atomic context issue, but it also added
devm management of the IRQ by actually switching to
devm_request_threaded_irq() (without any explanation in the commit
message for this change).
This is wrong since the IRQ was already explicitly managed by
the driver. On unbind the ASoC core will call rt5640_set_jack(NULL)
which in turn will call rt5640_disable_jack_detect() which
frees the IRQ already. So now we have a double free.
Besides the unexplained switch to devm being wrong, the actual fix
for the sleep in atomic context issue also is not the best solution.
The only thing which rt5640_irq() does is cancel + (re-)queue
the jack_work delayed_work. This can be done in a single non sleeping
call by replacing queue_delayed_work() with mod_delayed_work(),
which does not sleep. Using mod_delayed_work() is a much better fix
then adding a thread which does nothing other then queuing a work-item.
This patch is a straight revert of the troublesome changes, the switch
to mod_delayed_work() is done in a separate follow-up patch.
Fixes: 70a6404ff6 ("ASoC: rt5640: Fix sleep in atomic context")
Cc: Sameer Pujar <spujar@nvidia.com>
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Sameer Pujar <spujar@nvidia.com>:
This small series fixes redundant PLLA updates that happen for
each DAI link in the audio path. This helps to resolve DMIC clock
issue seen on Jetson TX2 platform.
The rpmsg pcm device is a device which should support
double buffering.
Found this issue with pipewire. When there is no
SNDRV_PCM_INFO_BATCH flag in driver, the pipewire will
set headroom to be zero, and because rpmsg pcm device
don't support residue report, when the latency setting
is small, the "delay" always larger than "target" in
alsa-pcm.c, that reading next period data is not
scheduled on time.
With SNDRV_PCM_INFO_BATCH flag in driver, the pipewire
will select a smaller period size for device, then
the task of reading next period data will be scheduled
on time.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1694414287-13291-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit ac950278b0 ("ASoC: add N cpus to M codecs dai link support")
added an additional local params in __soc_pcm_hw_params, for the CPU
side of the DAI. The snd_pcm_hw_params struct is pretty large (604
bytes) and keeping two local copies of it can make the stack frame
really large.
It is worth noting the variables are in separate code blocks so for
some optimisation levels in the compiler these will get automatically
combined keeping the stack frame reasonable. But better to manually
combine them to cover all cases.
Add a single local variable for __soc_pcm_hw_params and use in both
loops to shrink the stack frame.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230908085920.2906359-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 422f10adc3 ("ASoC: wm8960: Add support for the power supplies")
added regulator support to the wm8960 driver, but neglected to update
error handling in the probe function. This results in warning backtraces
if the probe function fails.
Fixes: 422f10adc3 ("ASoC: wm8960: Add support for the power supplies")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20230909120237.2646275-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
for_each_child_of_node performs an of_node_get on each
iteration, so a break out of the loop requires an
of_node_put.
This was done using the Coccinelle semantic patch
iterators/for_each_child.cocci
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20230907095521.14053-11-Julia.Lawall@inria.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
For spdif input to report the locked rate correctly, even when no capture
is running, the HW and reference clock must be started as soon as
the dai is probed.
Fixes: 5ce5658375 ("ASoC: meson: add axg spdif input")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20230907090504.12700-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver remove() must call pm_runtime_dont_use_autosuspend().
Drivers that call pm_runtime_use_autosuspend() must disable
it in driver remove(). Unfortunately until recently this was
only mentioned in 1 line in a 900+ line document so most
people hadn't noticed this. It has only recently been added
to the kerneldoc of pm_runtime_use_autosuspend().
THIS WON'T APPLY CLEANLY TO V6.5 AND EARLIER:
We will send a separate backported patch to stable.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230908101716.2658582-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tegra audio graph card has many DAI links which connects internal
AHUB modules and external audio codecs. Since these are DPCM links,
hw_params() call in the machine driver happens for each connected
BE link and PLLA is updated every time. This is not really needed
for all links as only I/O link DAIs derive respective clocks from
PLLA_OUT0 and thus from PLLA. Hence add checks to limit the clock
updates to DAIs over I/O links.
This found to be fixing a DMIC clock discrepancy which is suspected
to happen because of back to back quick PLLA and PLLA_OUT0 rate
updates. This was observed on Jetson TX2 platform where DMIC clock
ended up with unexpected value.
Fixes: 202e2f7745 ("ASoC: tegra: Add audio graph based card driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1694098945-32760-3-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A collection of fixes for 6.6-rc1. All small and easy ones.
- The corrections of the previous PCM iov_iter transitions
- Regression fixes in MIDI 2.0 / USB changes
- Various ASoC codec fixes for Cirrus, Realtek, WCD
- ASoC AMD quirks and ASoC Intel AVS driver workaround
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAmT5xkIOHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE9k8RAAkgeTtv8W3YWKvkMMf7kMEP4Go8COJ4pLqY4A
zPfJp//tDSKiOLPm8XzYYQQddTlcVc6iNbV/3Enw3Ov9xvnQxAk+N+5ciF+s27q5
KyxzKZneEOSJSCPHPcbcI0LgqpSH/b71S8NhGL48DXxCd+GHyHSind8hel6xi+u4
dQIL9cQOp1HGmKreMrHvsvY4ruG5SrnQ+GXjcnkmdmMWP17xtubAXcRWvZs/PMl4
dg5HNUDy/KuRbHnxTAee7tuGZyG10sLkS4UfP+J4gKGdOKQvltrQ7dTyG3dCKtRl
Ezq0++IY7asMAdBu39IDJdC7XFr4jNSmeZbqcmhX8PTggIUJuyHzfnC9pAadkXOn
B11ZJUL2I6QYI6UZyyvWTc2HD4+rxOvl6IkFkDgaiOD3chPTqhAwAhDUeFICSuBi
BPJ4fG2r0iEFP92dTli9Q2gY2fXkE24ndpwP+zWbt0zO0/nQPh0XfWO3x6Vt/ml1
NNNj12qx6w6I4k8kx+mj4zFewz7x8dTIdXLukYAPk5tlagXpora9u1tt0ZT72T22
+wintcjfIp6agKxcWVmKVXi2PFdQmrwpUe5lW5EPKhEXNcrQaTBOKb9MYvFrCTz3
6olHbocegqolNnTJ/uSRTBD0E5jkwpdbc3MbSKrxUpcyTyKZmPDpd9JuPLLJHPfn
BkFdx5U=
=txoJ
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of fixes for 6.6-rc1. All small and easy ones.
- The corrections of the previous PCM iov_iter transitions
- Regression fixes in MIDI 2.0 / USB changes
- Various ASoC codec fixes for Cirrus, Realtek, WCD
- ASoC AMD quirks and ASoC Intel AVS driver workaround"
* tag 'sound-fix-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (21 commits)
ALSA: hda/realtek - ALC287 I2S speaker platform support
ASoC: amd: yc: Fix a non-functional mic on Lenovo 82TL
ASoC: Intel: avs: Provide support for fallback topology
ALSA: seq: Fix snd_seq_expand_var_event() call to user-space
ALSA: usb-audio: Fix potential memory leaks at error path for UMP open
ALSA: hda/cirrus: Fix broken audio on hardware with two CS42L42 codecs.
ASoC: rt5645: NULL pointer access when removing jack
ASoC: amd: yc: Add DMI entries to support Victus by HP Gaming Laptop 15-fb0xxx (8A3E)
MAINTAINERS: Update the MAINTAINERS enties for TEXAS INSTRUMENTS ASoC DRIVERS
ALSA: sb: Fix wrong argument in commented code
ALSA: pcm: Fix error checks of default read/write copy ops
ASoC: Name iov_iter argument as iterator instead of buffer
ASoC: dmaengine: Drop unused iov_iter for process callback
ALSA: hda/tas2781: Use standard clamp() macro
ASoC: cs35l56: Waiting for firmware to boot must be tolerant of I/O errors
ASoC: dt-bindings: fsl_easrc: Add support for imx8mp-easrc
ASoC: cs42l43: Fix missing error code in cs42l43_codec_probe()
ASoC: cs35l45: Rename DACPCM1 Source control
ASoC: cs35l45: Fix "Dead assigment" warning
ASoC: cs35l45: Add support for Chip ID 0x35A460
...
A bunch of fixes and new IDs that came in since the initial pull request
- all driver specific and nothing too exciting.
There's a trivial conflict in the AMD driver ID table due to the last
v6.5 fixes not having been merged up.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmT5uzEACgkQJNaLcl1U
h9D1RAf/SrPNpWDm5nX0suSQiNqxyzeT+deZtYtKGaF0/rMdOLsnqQyPKV25s9xS
bqdI03oFMPfXOqfPW9F+4bmFBuWlL2kl1n1HZIx/bm8/lDCEBQVOXpOl56lHJpPv
I91dh/1eVUp20FtPwaLwMgPpVb/iJvVSol/IuSvjXICggDY2091F05nBWef2z93S
3tRVkDX4p+Ywra9lFexV0goRL/bCfdMSG8GHHurdVWB4y6fI1LC6eoPEYsLujzvx
92//HR7mx11uo9Kf+SiHBJVgZAzW9pJXpnjgTx3X/Isrfxv8h/MnSR3btUKDp3Ti
okxLvCujDZVhbVP6DiJEuCmXr0OXdQ==
=abtH
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.6-merge-window' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.6
A bunch of fixes and new IDs that came in since the initial pull request
- all driver specific and nothing too exciting.
There's a trivial conflict in the AMD driver ID table due to the last
v6.5 fixes not having been merged up.
HDA and HDMI devices are simple enough that in case of user not having
topology tailored to their device, they can use fallback topology.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230905093147.1960675-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Machine driver calls snd_soc_component_set_jack() function with NULL
jack and data parameters when removing jack in codec exit function.
Do not access data when jack is NULL.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Link: https://lore.kernel.org/r/20230904104046.4150208-1-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported issues.
The last bit of cleanups from Jiri and the tty structure size reduction
came in last week, a bit late but as they were just style changes and
size reductions, I figured they should get into this merge cycle so that
others can work on top of them with no merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH+jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKyACgldt6QeenTN+6dXIHS/eQHtTKZwMAn3arSeXI
QrUUnLFjOWyoX87tbMBQ
=LVw0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
While transitioning ASoC code for iov_iter usages, I kept the argument
name as "buf" as the original code. But, iov_iter is an iterator, and
using the name "buf" may be misleading: the crucial difference is that
iov_iter can be proceeded after the operation, hence it can't be
passed twice, while a simple "buffer" sounds as if reusable.
To make the usage clearer, rename the argument from "buf" to "iter".
There is no functional changes, just names.
Fixes: 66201cacc3 ("ASoC: component: Add generic PCM copy ops")
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/CAHk-=wje+VkXjjfVTmK-uJdG_M5=ar14QxAwK+XDiq07k_pzBg@mail.gmail.com
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230831130457.8180-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Passing the iov_iter to the process callback is rather buggy, as the
iterator has been already processed for playback. Similarly, it makes
the copy for capture buggy after the process callback reading the
iterator out. Moreover, all existing process callbacks don't refer to
the passed iterator at all. So, it's better to drop the argument from
the process callback.
Fixes: 9bebd65443 ("ASoC: dmaengine: Use iov_iter for process callback, too")
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/CAHk-=wje+VkXjjfVTmK-uJdG_M5=ar14QxAwK+XDiq07k_pzBg@mail.gmail.com
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230831130457.8180-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ignore failure to read from the cs35l56 when polling as the device will
NAK i2c accesses until it has booted and this would terminate the poll
of regmap_read_poll_timeout().
Fixes: 8a731fd37f ("ASoC: cs35l56: Move utility functions to shared file")
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230829160433.2647889-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
When clk_get_optional() fails, the error handling code does a 'goto
err_pm' with ret = 0, which is resturning success on a failure path.
Fix this by assigning the PTR_ERR(priv-mclk) to ret variable.
Fixes: fc918cbe87 ("ASoC: cs42l43: Add support for the cs42l43")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230829073635.1877367-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Mark Brown <broonie@kernel.org
Rename control to "DACPCM Source" for backward compatibility
with previous implementation.
Signed-off-by: Vlad Karpovich <vkarpovi@opensource.cirrus.com
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230828170525.335671-5-vkarpovi@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
These were some changes in my v6.4 branch that never got sent as fixes,
none of them super urgent thankfully.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmTstNgACgkQJNaLcl1U
h9Cdpgf/QobBZAA/QCr1o9+ghrqdGwkgYtwJixJPDvb8rv4eaU892CHtyIBLd0Li
bfhxDKyDIKkqomy/8ssjU2lg08aqX+2wgJxdsL/ni5lDJEa4YHSjTO1OwBL68w9F
5KL83dgdlzr91tHhwwJQ3DSBJolh37shAe+KiYicVHDEP+AP+3q559lBiT9hs+hB
eVe4IQ4mnJbHNRX+xmx/arrLZru+nPBKTJulkGtOnmqO0ZscwMAIqEiAor7yY9bG
lJjyt7N7oglRRngX/PVcHq+VpTPwPGWJ7K2qnrTJtnpVt+vD+4qpZSMbIwBAoApY
l8zWTjlrfFhMBiZOpyz62XrgQ8/Mhw==
=WIkh
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.5-merge-window' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes that got left after v6.4
These were some changes in my v6.4 branch that never got sent as fixes,
none of them super urgent thankfully.
A few newly added functions aren't built unless CONFIG_OF is set,
which result in the build failure due to defined-but-not-used errors.
Put "#ifdef CONFIG_OF" around those functions to suppress the build
error.
Fixes: 52ea7c0543 ("ASoC: dwc: i2s: Add StarFive JH7110 SoC support")
Link: https://lore.kernel.org/r/20230828113537.27600-1-tiwai@suse.de
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Three Qualcomm audio codecs (WCD9355, WCD934x and WCD938x) use the same
object file wcd-clsh-v2.o leading to warnings:
Makefile: wcd-clsh-v2.o is added to multiple modules: snd-soc-wcd9335 snd-soc-wcd934x snd-soc-wcd938x
Convert the wcd-clsh-v2.o to a module to solve it.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Link: https://lore.kernel.org/r/20230828132316.190386-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
The rest of the updates for v6.6, some of the highlights include:
- A big API cleanup from Morimoto-san, rationalising the places we put
functions.
- Lots of work on the SOF framework, AMD and Intel drivers, including a
lot of cleanup and new device support.
- Standardisation of the presentation of jacks from drivers.
- Provision of some generic sound card DT properties.
- Conversion oof more drivers to the maple tree register cache.
- New drivers for AMD Van Gogh, AWInic AW88261, Cirrus Logic cs42l43,
various Intel platforms, Mediatek MT7986, RealTek RT1017 and StarFive
JH7110.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmTo6Y0ACgkQJNaLcl1U
h9AnaAf/XiBSnZl2i9wFckPy7bLcR74YrP1sFet5ZAqtpIt+/DvzQlgFAraHJ4tR
ScM2ZyyMwREaFhrHIXKLm8kbaOKeIjIMSxiHREVG9Wibq8d1TwaOHWAcXc9jMsQb
3G23Aizy2h5yD+/VTh8q6aV+fmYZJDfr1tIu8zWva90HcL2fMGvLjVdt24RNejTL
bgCC2GaaGP4pnC3xoBo1hGayvp0PES1BHVeyAXqMVscH+GCplPNJEdSHvU14OBck
1Nfjf5NVkh5G0pvrbG/yblsn1Zm5HRAzCE7gF1OHLFH27ygvp7fGk6TIXXpvw23c
OSvveYee2YLrf4kyndmv88Aq8JVTeA==
=9F/T
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v6.6
The rest of the updates for v6.6, some of the highlights include:
- A big API cleanup from Morimoto-san, rationalising the places we put
functions.
- Lots of work on the SOF framework, AMD and Intel drivers, including a
lot of cleanup and new device support.
- Standardisation of the presentation of jacks from drivers.
- Provision of some generic sound card DT properties.
- Conversion oof more drivers to the maple tree register cache.
- New drivers for AMD Van Gogh, AWInic AW88261, Cirrus Logic cs42l43,
various Intel platforms, Mediatek MT7986, RealTek RT1017 and StarFive
JH7110.
A recent cleanup of soc_dai_link_sanity_check() is responsible for
generating lots of confusing errors before returning -EPROBE_DEFER:
acp5x_mach acp5x_mach.0: ASoC: Component acp5x_i2s_dma.0 not found for link acp5x-8821-play
[...]
acp5x_mach acp5x_mach.0: ASoC: Component spi-VLV1776:00 not found for link acp5x-CS35L41-Stereo
[...]
acp5x_mach acp5x_mach.0: ASoC: Component spi-VLV1776:01 not found for link acp5x-CS35L41-Stereo
Switch back to the initial behaviour of logging those messages on
KERN_DEBUG level instead of KERN_ERR.
While at it, use the correct form of the verb in 'component_not_find'
label.
Fixes: 0e66a2c694 ("ASoC: soc-core.c: cleanup soc_dai_link_sanity_check()")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com
Link: https://lore.kernel.org/r/20230824193837.369761-1-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org
Current audio-graph-card functions definition are like below
(A)' static int graph_get_dais_count();
(B) int audio_graph_parse_of(...)
{
...
(A) ret = graph_get_dais_count();
...
}
(A) static int graph_get_dais_count(...)
{
...
}
(C)
We don't need to have (A)' definition if audio_graph_parse_of() (B) was
defined at (C). This patch moves (B) to (C).
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com
Link: https://lore.kernel.org/r/87r0ntmc3c.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org
clang warns (or errors with CONFIG_WERROR=y):
sound/soc/codecs/cs42l43.c:1371:2: error: variable 'ret' is used uninitialized whenever switch default is taken [-Werror,-Wsometimes-uninitialized]
1371 | default:
| ^~~~~~~
sound/soc/codecs/cs42l43.c:1377:9: note: uninitialized use occurs here
1377 | return ret;
| ^~~
sound/soc/codecs/cs42l43.c:1349:9: note: initialize the variable 'ret' to silence this warning
1349 | int ret;
| ^
| = 0
1 error generated.
Initialize ret to 0 in the default case, as there was nothing to do for
other event types.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1922
Fixes: fc918cbe87 ("ASoC: cs42l43: Add support for the cs42l43")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230823-cs42l43_pll_ev-init-ret-v1-1-5836f1ad5dad@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Xingyu Wu <xingyu.wu@starfivetech.com>:
This patch series adds I2S support for the StarFive JH7110 RISC-V
SoC based on Designware I2S controller. There has three I2S channels
(RX/TX0/TX1) on the JH7110 SoC, one of which is for record(RX) and
two for playback(TX).
The first patch adds support for the StarFive JH7110 SoC in the
Designware I2S bindings.
The second patch adds the ops to get data from platform bus in the
I2S driver.
The third patch adds support for the StarFive JH7110 SoC in
the Designware I2S driver.
The fourth patch fixes the name of I2STX1 pinmux.
The last patch adds device node of I2S RX/TX0/TX1 in JH7110 dts.
This patch series is based on Linux-next(20230818) which is merge
clock, syscon and dma nodes for the StarFive JH7110 SoC.
The series has been tested and works normally on the VisionFive 2
board by plugging an audio expansion board.
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
Renesas Sound has ADG for clock control. Basically it needs
accurately divisible external input clock. But sometimes
sometimes it doesn't have to be accurate for some reason.
We can use ADG clk_i for such case. It came from CPG as
very high rate clock, but is not accurately divisible for
48kHz/44.1kHz rate, but enough for approximate rate.
This patch set support such use case.
We don't need to have "format" property on DT any more if
CPU/Codec driver has .auto_selectable_formats settings
on snd_soc_dai_ops. The sample dtsi doesn't have it.
To avoid user confusion, this patch indicates it on comment.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87edjuzk2p.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add StarFive JH7110(TX0/TX1/RX channels) SoC support in the
designware I2S driver and a flag to check if it is on the JH7110 SoC.
These channels need to enable clocks, resets and syscon register on the
JH7110 SoC. So add init ops in platform data for the JH7110 SoC to do this.
Their resets should be deassert before changing the parent of clocks so
these are done in the init ops of platform data.
The I2S controllers use DMA controller by platform data on the JH7110
and their settings about snd_dmaengine_dai_dma_data() should be added
in the dw_configure_dai_by_pd(). And use dmaengine PCM registration if
these do not have IRQ on the JH7110 SoC.
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Link: https://lore.kernel.org/r/20230821144151.207339-4-xingyu.wu@starfivetech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current adg.c will configure BRGCKR/BRRA/BRRB to output clock
when it start sound. OTAH, rsnd_adg_clk_enable() will enables
clk_a/b/c when driver was probed.
But it is strange, these should be set in the same time.
This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87h6oqzlei.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current adg has default division for BRRA/BRRB, but it was created at
very beginning of the driver implementation, and is now an unnecessary
settings.
Because it has this default division, unexpected clockout might
be selected. For example if it requests only 44.1kHz base clockout,
unrequested 48kHz base clockout also will be selected.
This patch remove default division of clock out
Reported-by: Vincenzo De Michele <vincenzo.michele@davinci.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87il96zlep.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current adg.c doesn't assume that requested clock out divide condition
doesn't match. In such case, it will indicate strange message, and will
register NULL clock, etc. It is just a DT setting miss, but is
confusable. This patch check all conditions for it.
Reported-by: Vincenzo De Michele <vincenzo.michele@davinci.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87lee2zlf7.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Basically Renesas sound ADG is assuming that it has accurately
divisible input clock. But sometimes / some board might not have it.
The clk_i from CPG is used for such case. It can't calculate accurate
division, but can be used as approximate rate.
This patch enable clk_i for such case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Adnan Ali <adnan.ali@bp.renesas.com>
Tested-by: Vincenzo De Michele <vincenzo.michele@davinci.de>
Tested-by: Patrick Keil <patrick.keil@conti-engineering.com>
Link: https://lore.kernel.org/r/87msyizlfd.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the hardware may be designed as a single-ended input, the headset mic
record only supports single-ended input on the left side. This patch
will enhance microphone recording performance for single-end.
Signed-off-by: Seven Lee <wtli@nuvoton.com>
Link: https://lore.kernel.org/r/20230823071244.1861487-2-wtli@nuvoton.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP_SW_INTR_STAT_OFFSET is a common interrupt register which will be
accessed by both ACP firmware and driver. This register contains register
bits corresponds to host to dsp interrupts and vice versa.
when dsp to host interrupt is reported, only clear dsp to host
interrupt bit in DSP_SW_INTR_STAT_OFFSET.
Fixes: 2e7c6652f9 ("ASoC: SOF: amd: Fix for handling spurious interrupts from DSP")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230823073340.2829821-7-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to scratch memory persistence, Once the DSP panic is reported, need to
clear the panic mask after handling DSP panic. Otherwise, It results in DSP
panic on next reboot.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230823073340.2829821-6-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Few AMD platforms require ACP ACLK as clock source.
Add conditional check for clock mux selection register for
switching between internal clock and ACP ACLK.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230823073340.2829821-5-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add module parameter for firmware debug. If firmware debug
flag is enabled, clear the fusion stall bit which is required
for enabling firmware debugging through JTAG.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230823073340.2829821-3-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously ACP SOF firmware used to enable the ACP external
global interrupt register.
This will restrict to report ACP host interrupts only after
firmware loading is successful.
This register needs to be set from host driver to handle
other ACP interrupts(SoundWire Interrupts) before loading
the ACP firmware.
Add field for external interrupt enable register in acp descriptor
structure and enable the external interrupt enable register.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230823073340.2829821-2-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During initial development time for RN platform, when SHA
dma gets completed, SHA DMA engine used to raise the ACP interrupt.
In ACP interrupt handler, SHA DMA interrupt got handled.
Currently SHA DMA compleition is verified by checking
transfer count using read poll time out logic.
Remove unused SHA dma interrupt handling code.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230823073340.2829821-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current analog gain TLV seems to have completely incorrect values in
it. The gain starts at 0.5dB, proceeds in 1dB steps, and has no mute
value, correct the control to match.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230823085308.753572-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC merges DAI call backs into .ops.
This patch merge these into one.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308152047.psX1QNDh-lkp@intel.com/
Cc: Randy Dunlap <rdunlap@infradead.org>
Fixes: 446b31e894 ("ASoC: soc-dai.h: remove unused call back functions")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/87a5ujubj0.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new module parameter ipc4_ignore_cpc which can be used to force the
kernel to ignore the queried CPC value for all firmware modules and use 0
instead.
The CPC lookup is still done to report missing configurations and the
debug print is going to be different to be explicit that the CPC is ignored
and what was the value we would have used.
The CPC value is sent to the firmware with the MOD_INIT_INSTANCE message
and it is used by the firmware as a parameter for clock scaling.
The flag is intended to be used only when there is a need to validate the
firmware behavior regarding to clock scaling since the 0 CPC value will
force the DSP to run in full speed, disabling the scaling and provides
additional counter point to rule out clock management related issues.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20230822065419.24374-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
The SRC component in a pipeline provides flexibility on the sampling
rate which was not handled previously. This series will improve the
kernel side with the needed logic to be able to deal with the SRC type
of components in pipelines.
If the copier has only output valid_bits across all its output
formats, the reference for selecting the output format must be set that
instead of the valid_bits from the selected input format.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230821113629.5017-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When we walk the list of connected widgets from the source to the sink
to prepare all widgets, the pipeline_params must be modified to reflect
the output audio format at each widget. But, the copier only modifies
the sample format in the pipeline_params. So, fix it to also modify the
rate and channels.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230821113629.5017-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For playback, the SRC sink rate must be configured based on the requested
output format which is restricted to only handle DAI's that support a
single audio format for now. For capture, the SRC module should convert
the rate to match the rate requested by the PCM hw_params.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230821113629.5017-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify the pipeline_params based on the SRC output format and set the
sink_rate in the IPC data.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230821113629.5017-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS42L43 is an audio CODEC with integrated MIPI SoundWire interface
(Version 1.2.1 compliant), I2C, SPI, and I2S/TDM interfaces designed
for portable applications. It provides a high dynamic range, stereo
DAC for headphone output, two integrated Class D amplifiers for
loudspeakers, and two ADCs for wired headset microphone input or
stereo line input. PDM inputs are provided for digital microphones.
The ASoC component provides the majority of the functionality of the
device, all the audio functions.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230804104602.395892-7-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
VivoBook Pro 15 Ryzen Edition uses Ryzen 6800H processor, and adding to
quirks list for acp6x will enable internal mic.
Signed-off-by: BrenoRCBrito <brenorcbrito@gmail.com>
Link: https://lore.kernel.org/r/20230818211417.32167-1-brenorcbrito@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 7ac3404c2e ("ASoC: amd: acp: Map missing jack kcontrols") adds
card kcontrols and DAPM widgets corresponding to jacks for Headphone and
Headset Mic. But these were already being added in acp-legacy-mach.c and
acp-sof-mach.c, so this causes a probe error:
sof_mach rt5682s-hs-rt1019: control 2:0:0:Headphone Jack Switch:0 is already present
sof_mach rt5682s-hs-rt1019: ASoC: Failed to add Headphone Jack Switch: -16
sof_mach rt5682s-hs-rt1019: devm_snd_soc_register_card(sof-rt5682s-hs-rt1019) failed: -16
sof_mach: probe of rt5682s-hs-rt1019 failed with error -16
Removing the new duplicates from the common code might be enough to fix
the issue. But some of the codecs use different kcontrols and widgets.
NAU8821 alone has an "Int Mic". MAX98360A has a single "Spk", while
RT1019 has "Left Spk" and "Right Spk" (and two codec instances with name
prefixes).
Since there are per-codec differences, add the kcontrols and widgets
in the common code as each dai-link is being initialized, instead of in
the two machine drivers' probe().
Also, MAX98388 has Left and Right instances, but uses a single "SPK"
widget. That seems weird, so normalize it to use two widgets (one per
each instance like RT1019) while we're adding controls.
Fixes: 7ac3404c2e ("ASoC: amd: acp: Map missing jack kcontrols")
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Link: https://lore.kernel.org/r/20230818080314.32991-1-alpernebiyasak@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch will improve the depop function of CBJ detection before the headphone playback
when the system resumes.
We also want to complete the CBJ detection in the system-level resume function.
It could avoid triggering the detection at the playing state of headphones.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20230818023732.2153170-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now all ASoC users have been replaced to use the new PCM copy ops,
let's drop the obsoleted copy_user ops and its helper function.
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230815190136.8987-25-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Along with the conversion to PCM copy ops, use the iov_iter for the
pointer to be passed to the dmaengine process callback, too. It
avoids the direct reference of iter_iov_addr(), and it can potentially
help for the drivers to access memory properly (although both atmel
and stm drivers don't use the given buffer address at all for now).
Reviewed-by: Mark Brown <broonie@kernel.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Olivier Moysan <olivier.moysan@foss.st.com>
Cc: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20230815190136.8987-23-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the ASoC dmaenging driver code to use the new
unified PCM copy callback. It's a straightforward conversion from
*_user() to *_iter() variants.
The process callback is still using the direct pointer as of now, but
it'll be converted in the next patch.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Reviewed-by: Mark Brown <broonie@kernel.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230815190136.8987-22-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the qcom lpass driver code to use the new unified
PCM copy callback. It's a straightforward conversion from *_user() to
*_iter() variants.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Reviewed-by: Mark Brown <broonie@kernel.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Banajit Goswami <bgoswami@quicinc.com>
Link: https://lore.kernel.org/r/20230815190136.8987-21-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the mediatek BT SCO driver code to use the new
unified PCM copy callback. It's a straightforward conversion from
*_user() to *_iter() variants. As copy_form/to_iter() updates the
internal offset at each read/write, we can drop the cur_*_idx counter
in the loop, too.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230815190136.8987-20-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For following the ALSA PCM core change, a new PCM copy ops is added
toe ASoC component framework: snd_soc_component_driver receives the
copy ops, and snd_soc_pcm_component_copy() helper is provided.
This also fixes a long-standing potential bug where the ASoC driver
covers only copy_user PCM callback and misses the copy from kernel
pointers (such as OSS PCM layer), too.
As of this patch, the old copy_user is still kept, but it'll be
dropped later after all drivers are converted.
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230815190136.8987-19-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Linus Walleij <linus.walleij@linaro.org>:
After dropping unused headers a few Realtek devices
actually using the GPIO descriptors remain.
Converting them to use optional GPIO descriptors is
pretty straight-forward.
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
These two patches add an ACPI HID and update the way the platform-
specific firmware identifier is extracted from the ACPI.
Convert the RT5682S to use GPIO descriptors and drop the
legacy GPIO headers.
We remove the global GPIO number from the platform data,
but it is still possible to create board files using GPIO
descriptor tables, if desired.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230817-descriptors-asoc-rt-v2-5-02fa2ca3e5b0@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the RT5682 to use GPIO descriptors and drop the
legacy GPIO headers.
We remove the global GPIO number from the platform data,
but it is still possible to create board files using GPIO
descriptor tables, if desired.
Make sure to make sure SDW devices can associate with
an LDO1 EN descriptor too, if they so desire by putting
the lookup into the common code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230817-descriptors-asoc-rt-v2-4-02fa2ca3e5b0@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the RT5668 to use GPIO descriptors and drop the
legacy GPIO headers.
We remove the global GPIO number from the platform data,
but it is still possible to create board files using GPIO
descriptor tables, if desired.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230817-descriptors-asoc-rt-v2-3-02fa2ca3e5b0@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The RT5665 driver has some stub support for GPIO descriptors
going back to the initial driver commit, where there are
two GPIO descriptors for the LDO and headphone detection
defined in the device state. Well, let's make use of the
descriptor properly.
We remove the global GPIO number from the platform data,
but it is still possible to create board files using GPIO
descriptor tables, if desired.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230817-descriptors-asoc-rt-v2-2-02fa2ca3e5b0@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The RT5640 driver is already using GPIO descriptors for some
stuff, all that is needed is to convert the remaining LDO1
control line to also use descriptors.
Simplify the code using gpiod_get_optional() and drop the
special "of" parsing function: these descriptors need not
come from device tree and it's optional so hey.
Keep some NULL checks around the GPIO operations even though
gpiolib is essentially NULL-tolerant, because by checking
for whether we have a valid GPIO descriptor or not we can
avoid a 400 ms delay which is great.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230817-descriptors-asoc-rt-v2-1-02fa2ca3e5b0@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for mt7986 board with wm8960.
Signed-off-by: Maso Huang <maso.huang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230817101338.18782-5-maso.huang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add mt7986 etdm dai driver support.
Signed-off-by: Maso Huang <maso.huang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230817101338.18782-3-maso.huang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add header files for register definition and structure.
Signed-off-by: Maso Huang <maso.huang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230817101338.18782-2-maso.huang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
fixed register access error when switching to other tas2781 -- refresh the page
inside regmap on the switched tas2781
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://lore.kernel.org/r/20230817093257.951-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
An ACPI ID has been allocated for CS35L56 ASoC devices so that they can
be instantiated from ACPI Device entries.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230817112712.16637-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a device property "cirrus,firmware-uid" to get the unique firmware
identifier instead of using ACPI _SUB. There aren't any products that use
_SUB.
There will not usually be a _SUB in Soundwire nodes. The ACPI can use a
_DSD section for custom properties.
There is also a need to support instantiating this driver using software
nodes. This is for systems where the CS35L56 is a back-end device and the
ACPI refers only to the front-end audio device - there will not be any ACPI
references to CS35L56.
Fixes: e496112529 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230817112712.16637-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
"samsung,audio-widgets" and "samsung,audio-routing" are not boolean
properties, thus more appropriate is to use of_property_present() to
check if they are present.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810063300.20151-7-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The call to snd_sof_find_spcm_dai() could return NULL,
add nullable check for the return value to avoid null
pointer defenrece.
Fixes: 7cb19007ba ("ASoC: SOF: ipc4-pcm: add hw_params")
Signed-off-by: Chao Song <chao.song@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230816133311.7523-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
'version' is an enum, thus cast of pointer on 64-bit compile test with
W=1 causes:
rockchip_pdm.c:587:18: error: cast to smaller integer type 'enum rk_pdm_version' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230815143204.379708-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
'devtype' is an enum, thus cast of pointer on 64-bit compile test with
W=1 causes:
wm8904.c:2205:21: error: cast to smaller integer type 'enum wm8904_type' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230815143204.379708-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
'type' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
tlv320aic32x4.c:1352:18: error: cast to smaller integer type 'enum aic32x4_type' from 'void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230815143204.379708-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
Use the FIRMWARE_MISSING flag in the CS35L56 to determine whether it is
safe to download a firmware patch.
Merge series from Li Zetao <lizetao1@huawei.com>:
This patch set use the helper function devm_kmemdup() to replace
devm_kmalloc + memcpy, which is the same as implementing the function
separately.
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
The use of the widget name as a prefix for the kcontrol name is quite
useful in the case of multiple pipelines going to the same endpoint,
but it's overkill in simpler cases.
This patchset extends the existing DAPM code to drop the widget name
prefix and make the kcontrol names simpler when there's no possible
ambiguity, e.g. "gain.2.1 Main Playback Volume" becomes just "Main
Playback Volume".
Only attempt to download wmfw/bin files to a non-secured part if
it reports FIRMWARE_MISSING. If FIRMWARE_MISSING is false the
firmware has already been patched and overwriting the patch could
corrupt the running firmware.
For a secured part the wmfw/bin can be downloaded even if
FIRMWARE_MISSING is false, because they will only patch tunings.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230815124826.5447-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a flag to wm_adsp_power_up() that indicates whether it should attempt
to find and load firmware files.
This is to support DSPs that have built-in firmware that may already have
been patched (for example, by the BIOS). In that case the patch must not
be overwritten because that could corrupt the running firmware.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230815124826.5447-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Existing HDA stream creation is split into two
for loops for capture and playback, but most of
the code in the two for loops are duplicated.
This patch refactors HDA stream creation with a
single for loop, thus remove code duplication.
No functional change in this patch.
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230814231519.79051-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding HDMI-In capture support for the RPL products doesn't have onboard
I2S codec.but need to support HDMI-In capture via I2S and audio playback
through HDMI/DP monitor.
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Balamurugan C <balamurugan.c@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230814231358.78971-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the acpi match table for Dell SKU0C87
devices, the codec layout is:
SDW0: RT714 DMIC
SDW1: RT1318 Speaker
SDW2: RT1318 Speaker
Note that there is no jack codec on SKU0C87 devices.
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230814231358.78971-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding HDMI-In capture via I2S feature support in RPL platfroms.
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Balamurugan C <balamurugan.c@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230814231358.78971-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding support for ES83x6 codec in RPL match table.
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Balamurugan C <balamurugan.c@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230814231358.78971-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adds SOF_TKN_COMP_NO_WNAME_IN_KCONTROL_NAME token, and copies the
token's tuple value to the no_wname_in_kcontrol_name flag in struct
snd_soc_dapm_widget.
If the tuple value for the token in the topology is true, then the
widget name is not added to the mixer name. In practice "gain.2.1 Post
Mixer Analog Playback Volume" becomes just "Post Mixer Analog Playback
Volume".
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Jyri Sarha <jyri.sarha@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230814232325.86397-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The existing soc-dapm code may add a prefix to control names, which in
some cases is useful but in others leads to long and confusing kcontrol
names such as "gain 2.1 Main Playback Volume".
This patch suggests an added flag to prevent the widget name prefix
from being added. That flag will be set in the topology file on a
per-widget basis.
The flag no_wname_in_kcontrol_name is added to struct snd_soc_dapm_widget,
and the logic in dapm_create_or_share_kcontrol() is changed to not to
add widget name if the flag is set.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Jyri Sarha <jyri.sarha@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230814232325.86397-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When snd_soc_card_jack_new is not called or the call fails,
calling this function causes a null pointer access
Signed-off-by: mnlife <mnlife@126.com>
Link: https://lore.kernel.org/r/20230811142511.6570-1-mnlife@126.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Boards were using this in older kernels before adl and rpl ids were
split. Add this back to maintain support.
Signed-off-by: Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230804085648.3721416-1-ajye_huang@compal.corp-partner.google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the helper function devm_kmemdup() rather than duplicating its
implementation, which helps to enhance code readability.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://lore.kernel.org/r/20230810114738.2103792-3-lizetao1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the helper function devm_kmemdup() rather than duplicating its
implementation, which helps to enhance code readability.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230810114738.2103792-2-lizetao1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The value of register(NDAC,MDAC,NADC,MADC,BCLKN) maybe zero lead to
divide by zero in clk_aic32x4_div_recalc_rate().And the rate should be
divide by 128 if the value was zero in this function according to the
datasheet.
Add the macro AIC32X4_DIV_MAX to present the 128 and return 0 if failing
to read the value of register.
Signed-off-by: Guiting Shen <aarongt.shen@gmail.com>
Link: https://lore.kernel.org/r/20230813125520.11067-1-aarongt.shen@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Simpilfy probe() by replacing of_device_get_match_data() and id lookup for
retrieving match data by i2c_get_match_data().
While at it, drop unused local variable np from probe().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230813073458.59606-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC merges DAI call backs into .ops.
This patch merge these into one.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87h6p99m55.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC merges DAI call backs into .ops.
This patch merge these into one.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Walker Chen <walker.chen@starfivetech.com>
Link: https://lore.kernel.org/r/87msz19m5r.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC merges DAI call backs into .ops.
This patch merge these into one.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Trevor Wu <trevor.wu@mediatek.com>
Link: https://lore.kernel.org/r/87sf8t9m6n.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC merges DAI call backs into .ops.
This patch merge these into one.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/87wmy59m7a.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
