If the call to devm_spi_register_master() fails on probe of the GPIO SPI
driver, the spi_master struct is erroneously not freed:
After allocating the spi_master, its reference count is 1. The driver
unconditionally decrements the reference count on unbind using a devm
action. Before calling devm_spi_register_master(), the driver
unconditionally increments the reference count because on success,
that function will decrement the reference count on unbind. However on
failure, devm_spi_register_master() does *not* decrement the reference
count, so the spi_master is leaked.
The issue was introduced by commits 8b797490b4 ("spi: gpio: Make sure
spi_master_put() is called in every error path") and 79567c1a32 ("spi:
gpio: Use devm_spi_register_master()"), which sought to plug leaks
introduced by 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO
descriptors") but missed this remaining leak.
The situation was later aggravated by commit d3b0ffa1d7 ("spi: gpio:
prevent memory leak in spi_gpio_probe"), which introduced a
use-after-free because it releases a reference on the spi_master if
devm_add_action_or_reset() fails even though the function already
does that.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org> # v4.17+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.1-: 8b797490b4db: spi: gpio: Make sure spi_master_put() is called in every error path
Cc: <stable@vger.kernel.org> # v5.1-: 45beec351998: spi: bitbang: Introduce spi_bitbang_init()
Cc: <stable@vger.kernel.org> # v5.1-: 79567c1a321e: spi: gpio: Use devm_spi_register_master()
Cc: <stable@vger.kernel.org> # v5.4-: d3b0ffa1d75d: spi: gpio: prevent memory leak in spi_gpio_probe
Cc: <stable@vger.kernel.org> # v4.17+
Cc: Navid Emamdoost <navid.emamdoost@gmail.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Link: https://lore.kernel.org/r/86eaed27431c3d709e3748eb76ceecbfc790dd37.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver doesn't do anything with the match for the device node. The
logic is the same as looking to see if a device node exists or not
because this driver wouldn't probe unless there is a device node match
when the device is created from DT. Just test for the presence of the
device node to simplify and avoid referencing a potentially undefined
match table when CONFIG_OF=n.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: <linux-spi@vger.kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20191004214334.149976-9-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In spi_gpio_probe an SPI master is allocated via spi_alloc_master, but
this controller should be released if devm_add_action_or_reset fails,
otherwise memory leaks. In order to avoid leak spi_contriller_put must
be called in case of failure for devm_add_action_or_reset.
Fixes: 8b797490b4 ("spi: gpio: Make sure spi_master_put() is called in every error path")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Link: https://lore.kernel.org/r/20190930205241.5483-1-navid.emamdoost@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify this function implementation by using a known function.
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b2dd074a-1693-3aea-42b4-da1f5ec155c4@web.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO SPI master has some code in its local CS
callback to set the initial sck GPIO value. This was
lost in the commit converting it to use SPI core
GPIO handling as this callback isn't called if the
internal GPIO handling is active.
Add the special SPI_MASTER_GPIO_SS to ascertain it
gets called anyway so we get the initial SCK setting
right. There is some platform provided GPIO handling
there as well but this will be skipped as the cs_gpios
will be NULL.
My test targets seem not to care about the initial
SCK value so I am uncertain if this is a regression,
but to preserve the previous semantic we better do
this.
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Fixes: 249e2632dc ("spi: gpio: Don't request CS GPIO in DT use-case")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190716204651.7743-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace spi_bitbang_start() with a combination of spi_bitbang_init()
and devm_spi_register_master() and drop all of the explicit
cleanup-related code that's no longer necessary.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a number of failure paths in spi_gpio_probe() that do not call
spi_master_put() potentially leaking memory. Fix this problem by
registering a cleanup funciont via devm_add_action_or_reset() right
after SPI controller is allocated.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no code using 'pdev' field in struct spi_gpio. Drop it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The logic of setting mflags in spi_gpio_request() is very simple and
there isn't much benefit in having it in that function. Move all of
that code outside into spi_gpio_probe() in order to simplify things.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
DT use-case already relies on SPI core to control CS (requested by
of_spi_register_master() and controlled spi_set_cs()), so there's no
need to try to request those GPIO in spi-gpio code. Change the code
such that spi-gpio's CS related code is only used if device is probed
via pdata.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion from GPIO numbers to GPIO descriptors removed the use of
spi->controller_data, but forgot to update a comment referring to it.
Fixes: 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop unused pdata copy in struct spi_gpio. No functional change
intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Swap branches of the if statement in order to simplify it's logical
condition being checked. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a local "struct spi_bitbang *bb" in spi_gpio_probe() for
brevity. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a local "struct device *dev" in spi_gpio_probe() for brevity. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Spi_to_pdata() is not used anywhere in the code. Drop it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
spi-gpio is capable of dealing with active-high chip-selects.
Unfortunately, commit 4b859db2c6 ("spi: spi-gpio: add SPI_3WIRE
support") broke this by setting master->mode_bits, which overrides
the setting in the spi-bitbang code. Fix this.
[Fixed a trivial conflict with SPI_3WIRE_HIZ support -- broonie]
Fixes: 4b859db2c6 ("spi: spi-gpio: add SPI_3WIRE support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The spi-gpio driver already handles different chip select polarities,
but so far this was not advertised in master->mode_bits.
This patch fixes mmc_spi on top of spi_gpio, which is useful in some
testing scenarios.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices such as the TPO TPG110 display panel require
a "high-impedance turn-around", in effect a clock cycle after
switching the line from output to input mode.
Support this in the GPIO driver to begin with. Other driver
may implement it if they can, it is unclear if this can
be achieved with anything else than GPIO bit-banging.
Cc: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a logical problem in spi-gpio with host just
assigning a MOSI line and no MISO: this is interpreted
as the host cannot do RX and the host is flagged with
SPI_MASTER_NO_RX.
This is wrong: since GPIO lines can switch direction,
in 3WIRE operation the host will simply reverse the
direction of the GPIO line and start reading from it,
there is even code for doing this in the driver, but
it went unnoticed because it was tested by using a
master with 4 wires but a device using just 3 wires.
Remove the offending flag.
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-gpio.c: In function 'spi_gpio_remove':
drivers/spi/spi-gpio.c:450:33: warning:
variable 'pdata' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes an embarrassing copy-and-paste error in the
errorpath of spi_gpio_request(): we were checking the wrong
struct member for error code right after retrieveing the
sck GPIO.
Fixes: 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add SPI_3WIRE support to spi-gpio controller introducing
set_line_direction function pointer in spi_bitbang data structure.
Spi-gpio controller has been tested using hts221 temp/rh iio sensor
running in 3wire mode and lsm6dsm running in 4wire mode
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the capability to specify the flag parameter used in
bitbang_txrx_be_cpha{0,1} through the txrx_word function pointers of
spi_bitbang data structure. That feature will be used to add spi-3wire
support to the spi-gpio controller
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the bit-banged GPIO SPI driver to looking up and
using GPIO descriptors to get a handle on GPIO lines for SCK,
MOSI, MISO and all CS lines.
All existing board files are converted in one go to keep it all
consistent. With these conversions I rarely find any interrim
steps that makes any sense.
Device tree probing and GPIO handling should work like before
also after this patch.
For board files, we stop using controller data to pass the GPIO
line for chip select, instead we pass this as a GPIO descriptor
lookup like everything else.
In some s3c24xx machines the names of the SPI devices were set to
"spi-gpio" rather than "spi_gpio" which can never have worked, I
fixed it working (I guess) as part of this patch set. Sometimes
I wonder how this code got upstream in the first place, it
obviously is not tested.
mach-s3c64xx/mach-smartq.c has the same problem and additionally
defines the *same* GPIO line for MOSI and MISO which is not going
to be accepted by gpiolib. As the lines were number 1,2,2 I assumed
it was a typo and use lines 1,2,3. A comment gives awat that line 0
is chip select though no actual SPI device is provided for the LCD
supposed to be on this bit-banged SPI bus. I left it intact instead
of just deleting the bus though.
Kill off board file code that try to initialize the SPI lines
to the same values that they will later be set by the spi_gpio
driver anyways. Given the huge number of weird things in these
board files I do not think this code is very tested or put in
with much afterthought anyways.
In order to assert that we do not get performance regressions on
this crucial bing-banged driver, a ran a script like this dumping the
Ilitek ILI9322 regmap 10000 times (it has no caching obviously) on
an otherwise idle system in two iterations before and after the
patches:
#!/bin/sh
for run in `seq 10000`
do
cat /debug/regmap/spi0.0/registers > /dev/null
done
Before the patch:
time test.sh
real 3m 41.03s
user 0m 29.41s
sys 3m 7.22s
time test.sh
real 3m 44.24s
user 0m 32.31s
sys 3m 7.60s
After the patch:
time test.sh
real 3m 41.32s
user 0m 28.92s
sys 3m 8.08s
time test.sh
real 3m 39.92s
user 0m 30.20s
sys 3m 5.56s
So any performance differences seems to be in the error margin.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
The assignment of SPI_GPIO_NO_CHIPSELECT to cs_gpios[0] causes the following
compiler warning, when building for 64 bit systems:
"warning: overflow in implicit constant conversion [-Woverflow]".
This is because the SPI_GPIO_NO_CHIPSELECT flag is a '-1' type casted to
unsigned long and cs_gpios is of the type int.
Furthermore the chip select's GPIO number is locally stored as unsigned int
and compared with SPI_GPIO_NO_CHIPSELECT. Thus the result of the comparison
is always false, if unsigned long and unsigned int have a different size.
As part of the fix this patch adds a check for the device tree's cs-gpios
property.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to describe a single slave device that has no chip select line
the 'num-chipselects' property has to be <0> and the 'cs-gpios' property
doesn't need to be set.
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the pointer-integer size mismatch warning below:
drivers/spi/spi-gpio.c: In function ‘spi_gpio_setup’:
drivers/spi/spi-gpio.c:252:8: warning: cast from pointer to integer of
different size [-Wpointer-to-int-cast]
cs = (unsigned int) spi->controller_data;
^
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The GPIO chip in use could be of any kind, and therefore might sleep
when accesing the GPIO lines. Take account of this by using cansleep
instead, which is the most generic case.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
'of_match_ptr' is defined in linux/of.h. Include it explicitly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Many drivers that use bitbang library have a leak on probe error paths.
This is because once a spi_master_get() call succeeds, we need an additional
spi_master_put() call to free the memory.
Fix this issue by moving the code taking a reference to master to
spi_bitbang_start(), so spi_bitbang_start() will take a reference to master on
success. With this change, the caller is responsible for calling
spi_bitbang_stop() to decrement the reference and spi_master_put() as
counterpart of spi_alloc_master() to prevent a memory leak.
So now we have below patten for drivers using bitbang library:
probe:
spi_alloc_master -> Init reference count to 1
spi_bitbang_start -> Increment reference count
remove:
spi_bitbang_stop -> Decrement reference count
spi_master_put -> Decrement reference count (reference count reaches 0)
Fixup all users accordingly.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Suggested-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Acked-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fill in the recently added spi_master.bits_per_word_mask field in as
many drivers as possible. Make related cleanups, such as removing any
redundant error-checking, or empty setup callbacks.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lukas Wunner