Add appropriate firmware-name property for all am33xx platforms.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[dfustini: change property from 'ti,scale-data-fw' to 'firmware-name']
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Message-Id: <20220502021508.1342869-3-dfustini@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PRU-ICSS target module node was left in disabled state in the
base am33xx-l4.dtsi file. PRU-ICSS is supported on the AM335x SK
EVM board, so enable this node to support PRUSS on this board. The
PRUSS node and most of its child nodes are already enabled in the
base dts file, and so become effective automatically with the
enabling of this PRU-ICSS target module node.
The corresponding PRU nodes can be disabled later on if there are
no use-cases defined to use a particular PRU core or the whole
PRU-ICSS subsystem itself if both its PRU cores are unused.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dtbs_check produces the following warning for ecap node name:
ecap@100: $nodename:0: 'ecap@100' does not match '^pwm(@.*|-[0-9a-f])*$'
Fix this by replacing ecap with pwm in node name
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dual_mac mode has been preserved the same way between legacy and new
driver, and one port devices works the same as 1 dual_mac port - it's safe
to switch drivers.
So, Switch amam335x-evm, am335x-evmsk and am335x-icev2 boards to use new
cpsw switch driver. Those boards have or 2 Ext. port wired and configured
in dual_mac mode by default, or only 1 Ext. port.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and following
the already supported Cortex-A1`5 and Cortex-A57 based Alpine chips.
This one is added together with the official Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile phone
chips from 2017 based on Cortex-A53 or Kryo 260 CPUs.
A total of five end-user products are added based on these, all
Android phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and
XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals.
It is added along with the HopeRun HiHope RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook
based on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels
and become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board
for the Tegra194, their latest 64-bit chip based on Carmel CPU
cores and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added:
The MYiR MYS-6ULX single-board computer, and four different
models of industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony
Xperia Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards.
Beacon EmbeddedWorks adds another SoM+Carrier development board
for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it
is based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Tpj3
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and
following the already supported Cortex-A1`5 and Cortex-A57 based
Alpine chips. This one is added together with the official
Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile
phone chips from 2017 based on Cortex-A53 or Kryo 260 CPUs. A total
of five end-user products are added based on these, all Android
phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals. It is added along with the HopeRun HiHope
RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook based
on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels and
become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board for
the Tegra194, their latest 64-bit chip based on Carmel CPU cores
and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added: The
MYiR MYS-6ULX single-board computer, and four different models of
industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony Xperia
Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards. Beacon EmbeddedWorks adds another
SoM+Carrier development board for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it is
based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)"
* tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (605 commits)
arm64: dts: meson: odroid-n2: add jack audio output support
arm64: dts: meson: odroid-n2: enable audio loopback
ARM: dts: berlin: Align L2 cache-controller nodename with dtschema
arm64: dts: qcom: Add Microsoft Lumia 950 (Talkman) device tree
arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree
arm64: dts: qcom: msm8992: Add RPMCC node
arm64: dts: qcom: msm8992: Add PSCI support.
arm64: dts: qcom: msm8992: Add PMU node
arm64: dts: qcom: msm8992: Add BLSP2_UART2 and I2C nodes
arm64: dts: qcom: msm8992: Add SPMI PMIC arbiter device
arm64: dts: qcom: msm8992: Add a SCM node
arm64: dts: qcom: msm8992: Add a proper CPU map
arm64: dts: qcom: bullhead: Move UART pinctrl to SoC
arm64: dts: qcom: bullhead: Add qcom,msm-id
arm64: dts: qcom: msm8992: Fix SDHCI1
arm64: dts: qcom: msm8992: Modernize the DTS style
arm64: dts: qcom: Add support for Sony Xperia Z5 (SoMC Sumire-RoW)
arm64: dts: qcom: Move msm8994-smd-rpm contents to lg-bullhead.
arm64: dts: qcom: msm8994: Add support for SMD RPM
arm64: dts: qcom: msm8992: Add a label to rpm-requests
...
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move mmc nodes to be compatible with the sdhci-omap driver. The following
modifications are required for omap_hsmmc specific properties:
ti,non-removable: convert to the generic mmc non-removable
ti,needs-special-reset: co-opted into the sdhci-omap driver
ti,dual-volt: removed. Legacy property not used in am335x or am43xx
ti,needs-special-hs-handling: removed. Legacy property not used in am335x
or am43xx
Also since the sdhci-omap driver does not support runtime PM, explicitly
disable the mmc3 instance in the dtsi.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move to use the new drm panel support in tilcdc together with added
"newhaven,nhd-4.3-480272ef-atxl"-panel support in drm panel-simple.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The default is enabled, and there should be no need to reconfigure
the status for SoC internal devices in the board specific files.
Only the USB PHY used needs to be configured in the board specific
files.
Cc: Bin Liu <b-liu@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The defines are taken from dt-bindings/pinctrl/am33xx.h
Signed-off-by: Christina Quast <cquast@hanoverdisplays.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Correctly map the regulators used by tlv320aic3106.
Both 1.8V and 3.3V for the codec is derived from VBAT via fixed regulators.
Cc: <Stable@vger.kernel.org> # v4.14+
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PHY must add both tx and rx delay and not only on the tx clock.
The board uses AR8031_AL1A PHY where the rx delay is enabled by default,
the tx dealy is disabled.
The reason why rgmii-txid worked because the rx delay was not disabled by
the driver so essentially we ended up with rgmii-id PHY mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like I missed the ranges for am335x epwmss. Let's set it up the
same way as for am437x and dra7.
Fixes: 87fc89ced3 ("ARM: dts: am335x: Move l4 child devices to probe
them with ti-sysc")
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert AM33xx to use the new clockdomain based layout. Previously the
clkctrl split was based on CM instance boundaries. The new layout
helps with introducing the interconnect driver instances.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wl1835mod.pdf data sheet says this pretty clearly for WL_IRQ line:
"WLAN SDIO out-of-band interrupt line. Set to rising edge (active high)
by default."
And it seems this interrupt can be optionally configured to use falling
edge too since commit bd763482c8 ("wl18xx: wlan_irq: support platform
dependent interrupt types").
On omap4, if the wlcore interrupt is configured as level instead of edge,
L4PER will stop doing hardware based idling after ifconfig wlan0 down is
done and the WL_EN line is pulled down.
The symptoms show up with L4PER status registers no longer showing the
IDLEST bits as 2 but as 0 for all the active GPIO banks and for
L4PER_CLKCTRL. Also the l4per_pwrdm RET count stops increasing in
the /sys/kernel/debug/pm_debug/count.
While there is also probably a GPIO related issue that needs to be
still fixed, this change gets us to the point where we can have L4PER
idling.
I'm guessing wlcore was at some point configured to use level interrupts
because of edge handling issues in gpio-omap. However, with the recent
fixes to gpio-omap the edge interrupts seem to be working just fine.
Let's change it for all omap boards with wlcore interrupt set as level.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com updated comments a bit for gpio issue]
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am335x-evm, am335x-evmsk and am335x-beaglebone are currently relying on
pinmux set by the bootloader to set the correct value for mmc1. Fix
this by adding pinmux data for the same in kernel.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add clkctrl nodes for AM33xx SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mmc2 used for wl12xx was missing the keep-power-in suspend
parameter. As a result the board couldn't reach suspend state.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
rtc can either be supplied from internal 32k clock or external crystal
generated 32k clock. Internal clock is SoC specific and the external
clock is board dependent. Assigning the corresponding clocks.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add blue-and-red-wiring -property to lcdc node. The am335x-evmsk has
blue and red wires crossed to get 24-bit RGB (and 16-bit BGR)
support. After this patch am335x-evmsk supports BGR565, RGB888, and
XRGB8888 color formats. See details in
Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Whitespace cleanup of lcdc related nodes. Do all indentation and
alignment with tabs instead of spaces.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /leds/led@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /gpio_keys/button0@10 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we are moving to OPPv2 bindings and able to add 1GHz OPP for
MPU, let's update the max MPU voltage range to align with the maximum
possible value allowed in the operating-points table, which is max
target voltage of 132500 uV + 2%.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Also, use the mux defines instead of magic numbers for the padconf
values when defining the pinctrl lines to make it more readable.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM335x the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sound support consist only Headset output on the board and can be
handled by "simple-audio-card"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While Sitara AM335x SoCs are very close to OMAP SoCs, the 32-line GPIO
controllers are numbered from 0 on AM335x and from 1 on OMAP. But when
the configuration for the TI WLAN controllers was converted from
platform data to device tree, this detail was overlooked, as 10 boards
were using OMAP with the WL12xx and WL18xx controllers, and only one
was based on AM335x.
This invalid configuration prevents the WL1271 module on the AM335x
EVM-SK from notifying interrupts to the SoC, and breaks the wlan driver.
The DTS must be corrected to use the correct GPIO controller.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace all the pdata-quirks for setting wl12xx/wl18xx
platform data with proper DT definitions.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Document and use new cadence serial binding
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlPI73sACgkQykllyylKDCGYzQCggc3g80f6R008+SNKlrN0Wuy+
b9kAnjqTO0Q0kDf4PlI/a5EVsfPmOzoS
=Bo6W
-----END PGP SIGNATURE-----
Merge tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx into next/dt
Merge "Xilinx Zynq changes for v3.17" from Michal Simek:
arm: Xilinx Zynq dt patches for v3.17
- Document and use new cadence serial binding
* tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: DT: Migrate UART to Cadence binding
tty: cadence: Document DT binding
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
The use of FIFO in McASP can reduce the risk of audio under/overrun and
lowers the load on the memories since the DMA will operate in bursts.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the necessary nodes to enable the LCD controller and the
LCD panel that is attached to the Texas Instruments AM335x
EVMSK platform. Also setup the necessary pin mux within the
DT file to drive the LCD connector and add the correct
pinmux settings for the lcd pins to be configured to when
the SoC goes into sleep state for the minimum power
consumption.
For the sleep mode LCD pin settings, MUX_MODE7 is chosen as
this corresponds to switching the pins into input GPIO's with
an internal pulldown. Which has been determined to offer the
lowest power solution vs leaving the pins configured in LCD
mode.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Wolfram Sang <wsa@sang-engineering.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make sure ethernet and mdio nodes are disabled by default and enable
them explicitly only on boards that actually use them.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VTT regulator for DDR3 termination on the am335x-evmsk is
controlled by a gpio. It is configured by the bootloader so here we
define an always-on, fixed voltage regulator to hold the gpio.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In "ARM: dts: am33xx: correcting dt node unit address for usb", the
usb_ctrl_mod and cppi41dma nodes were updated with the correct register
addresses. However, the dts files that reference these nodes were not
updated, and those devices are no longer being enabled.
This patch corrects the references for the affected dts files.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are sent separately from the rest of the .dts changes
as these depend on the fixes merged into v3.14-rc4, and
needed a bit more time to get updated on the fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=rAdr
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.15/dt-overo-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Updates to the .dts files to support more Gumstix boards.
These are sent separately from the rest of the .dts changes
as these depend on the fixes merged into v3.14-rc4, and
needed a bit more time to get updated on the fixes.
* tag 'omap-for-v3.15/dt-overo-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add support for the Overo Summit
ARM: dts: Add support for the Overo Chestnut43
ARM: dts: Add support for the Overo Alto35
ARM: dts: Add support for the Overo Gallop43
ARM: dts: Add support for the Overo Palo43
ARM: dts: overo: Add LIS33DE accelerometer
ARM: dts: overo: Create a file for common Gumstix peripherals
ARM: dts: overo: Push uart3 pinmux down to expansion board
ARM: dts: omap3-tobi: Add AT24C01 EEPROM
ARM: dts: omap3-tobi: Use include file omap-gpmc-smsc9221
ARM: dts: omap: Add common file for SMSC9221
ARM: dts: omap3-overo: Add HSUSB PHY
ARM: dts: omap3-overo: Enable WiFi/BT combo
ARM: dts: omap3-overo: Add missing pinctrl
ARM: dts: omap3-tobi: Add missing pinctrl
ARM: dts: overo: reorganize include files
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/boot/dts/omap3-overo.dtsi
EVM board provides two Ethernet ports, this patch sets them into
dual_emac mode to provide two independent network interfaces.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
