Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ8041 PHYs on RZ/G1 and R-Car Gen2 boards. This allows software to
identify the PHY model at any time, regardless of the state of the PHY
reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/f9e26625924f90eff34fe6f6f02b15fa272c5d80.1631174218.git.geert+renesas@glider.be
The GPIO pins connected to the 4 Software Switches ("SOFT_SW", SW2) do
not have external pull-up resistors, but rely on internal pull-ups being
enabled. Fortunately this is satisfied by the initial state of these
pins.
Make this explicit by enabling bias-pull-up, to remove the dependency on
initial state and/or boot loader configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132941.3938516-1-geert+renesas@glider.be
After set PROBE_PREFER_ASYNCHRONOUS flag on the mmc host drivers,
the order of /dev/mmcblkN was not fixed in some SoCs which have
multiple SDHI and/or MMCIF controllers. So, we were hard to use
such a device as rootfs by using the kernel parameter like
"root=/dev/mmcblkNpM".
According to the discussion on a mainling list [1], we can add
mmc aliases to fix the issue. So, add such aliases into R-Car Gen2
board dts files. Note that, since R-Car Gen2 is even more complicated
about SDHI and/or MMCIF channels variations and they share pins,
add the aliases into board dts files instead of SoC dtsi files.
[1]
https://lore.kernel.org/linux-arm-kernel/CAPDyKFptyEQNJu8cqzMt2WRFZcwEdjDiytMBp96nkoZyprTgmA@mail.gmail.com/
Fixes: 7320915c88 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.14")
Fixes: 21b2cec61c ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1613131316-30994-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
To improve human readability and enable automatic validation, the tuples
in "playback" and "capture" properties in sound device nodes should be
grouped using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210204130517.1647073-3-geert+renesas@glider.be
Small fixes to make these DTs compliant with the adi,adv7511w and
adi,adv7513 bindings:
r8a7745-iwg22d-sodimm-dbhd-ca.dts
r8a7790-lager.dts
r8a7790-stout.dts
r8a7791-koelsch.dts
r8a7791-porter.dts
r8a7792-blanche.dts
r8a7793-gose.dts
r8a7794-silk.dts:
Remove the adi,input-style and adi,input-justification properties.
r8a7792-wheat.dts:
Reorder the I2C slave addresses of hdmi@3d and hdmi@39 and remove
the adi,input-style and adi,input-justification properties.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200511110611.3142-3-ricardo.canuelo@collabora.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The ethernet PHY reset GPIO was missing and the kernel was depending
solely on the bootloader to bring the PHY out of reset. Fix this to
get rid of the dependency on bootloader.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200115051225.7346-1-marek.vasut@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
To improve human readability and enable automatic validation, the tuples
in the "states" properties of device nodes compatible with
"regulator-gpio" should be grouped, as reported by "make dtbs_check":
$ make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/regulator/gpio-regulator.yaml
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi0: states:0: Additional items are not allowed (1800000, 0 were unexpected)
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi0: states:0: [3300000, 1, 1800000, 0] is too long
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi1: states:0: Additional items are not allowed (1800000, 0 were unexpected)
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi1: states:0: [3300000, 1, 1800000, 0] is too long
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi2: states:0: Additional items are not allowed (1800000, 0 were unexpected)
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi2: states:0: [3300000, 1, 1800000, 0] is too long
...
Fix this by grouping the tuples using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191213164115.3697-2-geert+renesas@glider.be
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Convert bootargs from ip=dhcp to ip=on
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PMIC IRQ line pin multiplexing configuration is missing from the DTs.
Since the line is configured correctly by default, the system works fine.
However, add the IRQ line pin multiplexing configuration for completeness.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The LVDS0 encoder on Koelsh and Porter, and the LVDS1 encoder on Lager,
are enabled in DT but have no device connected to their output. This
result in spurious messages being printed to the kernel log such as
rcar-du feb00000.display: no connector for encoder /soc/lvds@feb90000, skipping
Fix it by disabling the encoders.
Fixes: 15a1ff30d8 ("ARM: dts: r8a7790: Convert to new LVDS DT bindings")
Fixes: e5c3f4707f ("ARM: dts: r8a7791: Convert to new LVDS DT bindings")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is a branch with a few merge requests that either came in late, or
took a while longer for us to review and merge than usual and thus cut
it a bit close to the merge window. We stage them in a separate branch
and if things look good, we still send them up -- and that's the case
here.
This is mostly DT additions for Renesas platforms, adding IP block
descriptions for existing and new SoCs.
There are also some driver updates for Qualcomm platforms for SMEM/QMI
and GENI, which is their generalized serial protocol interface.
-----BEGIN PGP SIGNATURE-----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=RUL0
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late updates from Olof Johansson:
"This is a branch with a few merge requests that either came in late,
or took a while longer for us to review and merge than usual and thus
cut it a bit close to the merge window. We stage them in a separate
branch and if things look good, we still send them up -- and that's
the case here.
This is mostly DT additions for Renesas platforms, adding IP block
descriptions for existing and new SoCs.
There are also some driver updates for Qualcomm platforms for SMEM/QMI
and GENI, which is their generalized serial protocol interface"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (186 commits)
soc: qcom: smem: introduce qcom_smem_virt_to_phys()
soc: qcom: qmi: fix a buffer sizing bug
MAINTAINERS: Update pattern for qcom_scm
soc: Unconditionally include qcom Makefile
soc: qcom: smem: check sooner in qcom_smem_set_global_partition()
soc: qcom: smem: fix qcom_smem_set_global_partition()
soc: qcom: smem: fix off-by-one error in qcom_smem_alloc_private()
soc: qcom: smem: byte swap values properly
soc: qcom: smem: return proper type for cached entry functions
soc: qcom: smem: fix first cache entry calculation
soc: qcom: cmd-db: Make endian-agnostic
drivers: qcom: add command DB driver
arm64: dts: renesas: salvator-common: Add ADV7482 support
ARM: dts: r8a7740: Add CEU1
ARM: dts: r8a7740: Add CEU0
arm64: dts: renesas: salvator-common: enable VIN
arm64: dts: renesas: r8a77970: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a77965: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7796: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7795-es1: add CSI-2 node
...
The vin port nodes does not have an address and thus does not need
address-cells or address size-properties.
This is flagged by dtc as follows:
# make dtbs W=1
arch/arm/boot/dts/r8a7791-koelsch.dtb: Warning (avoid_unnecessary_addr_size): /soc/video@e6ef0000/port: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
arch/arm/boot/dts/r8a7791-koelsch.dtb: Warning (avoid_unnecessary_addr_size): /soc/video@e6ef1000/port: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Enable the watchdog, so the board can be restarted by a watchdog
timeout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The internal LVDS encoder now has DT bindings separate from the DU. Port
the device tree over to the new model.
Fixes: c6a27fa41f ("drm: rcar-du: Convert LVDS encoder code to bridge driver")
Fixes: bb21803ea4 ("ARM: dts: r8a7791: add soc node")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Make it possible to fallback to GPIO for I2C4 on the EXIO-E connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed aliases, switched to named GPIOS, fixed pinmux for I2C4]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Create a separate bus for HDMI related I2C2 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed aliases, switched to named GPIOs, sorted by SCL
pins]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Commits 7d29f509d2 ("dt-bindings: i2c: i2c-gpio: Add support for
named gpios") and 05c7477885 ("i2c: gpio: Add support for named
gpios in DT") introduced named i2c-gpio DT bindings, and deprecated the
more error-prone unnamed variant.
Switch to the new bindings, and add the missing GPIO_OPEN_DRAIN I/O
flags, which were implicitly assumed before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Renesas part number of the two-wire serial interface EEPROM is not
24C02, but R1EX24002ATAS0G.
Hence change its primary compatible value to "renesas,r1ex24002", like
on Gose.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
cec-clock is a fixed clock generator that is not controlled by i2c5 and
thus should not be a child of the i2c5 bus node. Rather, it should be
a child of the root node of the DT.
Fixes: 02a5ab18d3 ("ARM: dts: koelsch: Add CEC clock for HDMI transmitter")
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Convert the R-Car M2-W SoC from the old "Renesas R-Car Gen2 Clock Pulse
Generator (CPG)", "Renesas CPG DIV6 Clock", and "Renesas CPG Module Stop
(MSTP) Clocks" DT bindings to the new unified "Renesas Clock Pulse
Generator / Module Standby and Software Reset" DT bindings.
This simplifies the DTS files, and allows to add support for reset
control later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The adv7511 on the Koelsch board has a 12 MHz fixed clock
for the CEC block. Specify this in the dts to enable CEC support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The X2 crystal oscillator on the Koelsch development board provides a
74.25 MHz clock, not a 148.5 MHz clock.
Fixes: cd21cb46e1 ("ARM: shmobile: koelsch: Add DU external pixel clocks to DT")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk and pcie_bus_clk device nodes are already enabled in
r8a7791.dtsi, so there is no need to update their statuses again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
And the sd-uhs-sdr104 property to SDHI0.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Make it possible to fallback to GPIO for I2C1 on the EXIO-C connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased and fixed aliases]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Add support in the dts for the HDMI input. Based on the Lager dts
patch from Ulrich Hecht.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[uli: removed "renesas," prefixes from pfc nodes]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the "1v8" pinctrl state and sd-uhs-sdr50 property to SDHI{0,1,2}.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Name the Pin Function Controller subnodes for QSPI and MSIOF0 after
their device names, instead of after the spi interface aliases.
This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnodes for SCIF0 and SCIF1 after
their device names, instead of after the serial port aliases.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Warning (unit_address_vs_reg): Node /regulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@5 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Correct preset_lpj calculation which may lead to too short delays
* Correct handling of optional clocks on r8a7791 to restore
access to the serial port the porter board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=k7qU
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC Fixes for v4.6
* Correct preset_lpj calculation which may lead to too short delays
* Correct handling of optional clocks on r8a7791 to restore
access to the serial port the porter board
This is a backmerge of v4.6 fixes, to avoid a merge conflict between 4.6
and our next/dt branch.
* tag 'renesas-fixes-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: timer: Fix preset_lpj leading to too short delays
Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
ARM: dts: r8a7791: Don't disable referenced optional clocks
clk_get on a disabled clock node will return EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their clocks property.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them to prevent this.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Fixed rate and fixed factor clocks do not require an
clock-output-names property.
* Since 07705583e9 ("clk: shmobile: div6: Make clock-output-names
optional") Renesas div6 clocks do not require a clock-output-names
property.
In the above cases there is only one clock output and its name is taken
from that of the clock node. Accordingly, remove the unnecessary
clock-output-names properties and as necessary update the node names.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since 16ccaf5bb5 ("pinctrl: sh-pfc: Accept standard function, pins and
groups properties") renesas pfc drivers accept generic "function", "pins"
and "groups" properties.
This patch updates the koelsch device tree to use the generic properties.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates:
- SCIF:
- Supports now 50, 75, 110, 1152000, 1500000, 2000000, and
4000000 bps,
- Perfect match for standard 50-460800, and 9216000 bps.
- More accurate 576000 bps.
- HSCIF:
- Supports now 50, 75, 110, 134, 150, and 200 bps,
- Perfect match for standard 50-460800, and 9216000 bps.
- More accurate 576000, 1152000, 3000000, 3500000, and 4000000
bps.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit e488ca9f8d ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The signals output by the DU to the HDMI transmitter use full 24-bit
RGB. Make sure all pins are properly muxed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commits 5cfdedb7b9 ("mtd: ofpart: move ofpart partitions to a
dedicated dt node") and fe2585e9c2 ("doc: dt: mtd: support
partitions in a special 'partitions' subnode"), having partitions as
direct subnodes of an mtd device is discouraged:
spi0.0: 'partitions' subnode not found on /spi@e6b10000/flash@0. Trying to parse direct subnodes as partitions.
Hence move the SPI FLASH partitions to a "partitions" subnode.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Because of historical reason, audio clock didn't use CCF.
Let's use it now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It is easy to modify settings for Test or other purpose if sound has label
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Describe DMA for the serial ports of R-Car Gen2 SoCs
* Add MMCIF max-frequency to R-Car Gen2 SoCs
* Use "nor-jedec" instead of "jedec,spi-nor"
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OIk0
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Second Round of Renesas ARM Based SoC DT Updates for v4.2" from Simon Horman:
* Describe DMA for the serial ports of R-Car Gen2 SoCs
* Add MMCIF max-frequency to R-Car Gen2 SoCs
* Use "nor-jedec" instead of "jedec,spi-nor"
* tag 'renesas-dt2-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790 dtsi: Describe DMA for the serial ports
ARM: shmobile: r8a7791 dtsi: Describe DMA for the serial ports
ARM: shmobile: r8a7794 dtsi: Describe DMA for the serial ports
ARM: shmobile: r8a7791: add MMCIF max-frequency
ARM: shmobile: r8a7790: add MMCIF max-frequency
ARM: shmobile: bockw dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: henninger dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: bockw-reference dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: koelsch dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: lager dts: Replace "nor-jedec" by "jedec,spi-nor"
* Enable DMA for HSUSB on r8a7790 and r8a7791 SoCs
* Configure the HOME key as wake-up source on kzm9g board
* Use generic names for device nodes on SH Mobile SoCs and boards
* Add "nor-jedec" compatible value to SH Mobile boards
* Add IRQC clock to r8a73a4, r8a779* SoCs
* Remove MSIOF address from r8a7790 and r8a7791 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OdRc
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.2" from Simon Horman:
* Enable DMA for HSUSB on r8a7790 and r8a7791 SoCs
* Configure the HOME key as wake-up source on kzm9g board
* Use generic names for device nodes on SH Mobile SoCs and boards
* Add "nor-jedec" compatible value to SH Mobile boards
* Add IRQC clock to r8a73a4, r8a779* SoCs
* Remove MSIOF address from r8a7790 and r8a7791 SoCs
* tag 'renesas-dt-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
ARM: shmobile: r8a7791: Enable DMA for HSUSB
ARM: shmobile: r8a7791: add USB-DMAC device nodes
ARM: shmobile: r8a7790: Enable DMA for HSUSB
ARM: shmobile: r8a7790: add USB-DMAC device nodes
ARM: shmobile: kzm9g dts: Configure the HOME key as wake-up source
ARM: shmobile: koelsch dts: Use generic names for device nodes
ARM: shmobile: lager dts: Use generic names for device nodes
ARM: shmobile: bockw dts: Use generic names for device nodes
ARM: shmobile: koelsch dts: Add "nor-jedec" compatible value
ARM: shmobile: bockw dts: Add "nor-jedec" compatible value
ARM: shmobile: lager dts: Add "nor-jedec" compatible value
ARM: shmobile: bockw-reference dts: Add "nor-jedec" compatible value
ARM: shmobile: henninger dts: Add "nor-jedec" compatible value
ARM: shmobile: armadillo800eva dts: Use generic names for device nodes
ARM: shmobile: marzen dts: Use generic names for device nodes
ARM: shmobile: kzm9d dts: Use generic names for device nodes
ARM: shmobile: ape6evm dts: Use generic names for device nodes
ARM: shmobile: sh73a0 dtsi: Use generic names for device nodes
ARM: shmobile: r8a7791 dtsi: Use generic names for device nodes
ARM: shmobile: r8a7790 dtsi: Use generic names for device nodes
...
