The GPIO pins connected to the 4 Software Switches (SW2) and the second
Tact Switch (SW25) do not have external pull-up resistors, but rely on
internal pull-ups being enabled. Fortunately this is satisfied by the
initial state of these pins.
Make this explicit by enabling bias-pull-up, to remove the dependency on
initial state and/or boot loader configuration.
Note that the GPIO pin connected to the first Tact Switch (SW24) does
have an external pull-up resistor.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/011e4c461767f2dd690b655b3dd501eb554184c1.1619785905.git.geert+renesas@glider.be
Small fixes to make these DTs compliant with the adi,adv7511w and
adi,adv7513 bindings:
r8a7745-iwg22d-sodimm-dbhd-ca.dts
r8a7790-lager.dts
r8a7790-stout.dts
r8a7791-koelsch.dts
r8a7791-porter.dts
r8a7792-blanche.dts
r8a7793-gose.dts
r8a7794-silk.dts:
Remove the adi,input-style and adi,input-justification properties.
r8a7792-wheat.dts:
Reorder the I2C slave addresses of hdmi@3d and hdmi@39 and remove
the adi,input-style and adi,input-justification properties.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200511110611.3142-3-ricardo.canuelo@collabora.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Convert bootargs from ip=dhcp to ip=on
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PMIC IRQ line pin multiplexing configuration is missing from the DTs.
Since the line is configured correctly by default, the system works fine.
However, add the IRQ line pin multiplexing configuration for completeness.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add IIC3 node to R8A7792 SoC device tree and a DA9063 PMIC node
to V2H Blanche board device tree.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the watchdog, so the board can be restarted by a watchdog
timeout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert the R-Car V2H SoC from the old "Renesas R-Car Gen2 Clock Pulse
Generator (CPG)" and "Renesas CPG Module Stop (MSTP) Clocks" DT bindings
to the new unified "Renesas Clock Pulse Generator / Module Standby and
Software Reset" DT bindings.
This simplifies the DTS files, and allows to add support for reset
control later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the general purpose LEDs on the Blanche board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Blanche board dependent part of the DU device node.
Add the device nodes for the Analog Devices ADV7511W HDMI transmitter
(connected to DU0) and ADV7123 video DAC (connected to DU1). Add the
necessary subnodes to interconnect DU, HDMI/VDAC devices, and HDMI/VGA
connectors.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Blanche board dependent part of the SDHI0 (connected to the
micro-SD slot) device node along with the necessary voltage regulator.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the general purpose software switches SW2 and tactile
switches SW24/25 as a virtual keyboard (like it was done with the Lager/
Koelsch boards).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Blanche board dependent part of the CAN0 device node along with
the CAN_CLK crystal.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) pin data for the SMSC LAN89218 Ethernet chip
to the Blanche board's device tree: the chip's IRQ output is connected to
the SoC's IRQ0 pin and its nCS input is connected to the SoC's EX_CS0# pin.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) SCIF0/3 pin data to the Blanche board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R8A7792 SoC doesn't have the EtherMAC core, so SMSC LAN89218 Ethernet
chip was used instead on the Blanche board; this chip is compatible with
SMSC LAN9115 for which there's a (device tree aware) driver. Describe
the chip in the Blanche device tree; enable DHCP and NFS root in the
kernel command line for the kernel booting.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7792 SoC based Blanche board.
The board has 2 debug serial ports: SCIF0 and SCIF3; include support for
them, so that the serial console can work.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
