The value from a readl is being masked with ITE_REG_CIOCAN_MASK however
this is not being used and cfg is being re-assigned. I believe the
assignment operator should actually be instead the |= operator.
Detected by CoverityScan, CID#1467987 ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Propagate the v4l2_mbus_framefmt to the source pad when either a sink
pad is activated or when the format of the active sink pad changes.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Now that FB_OMAP has stubs, the omap2 media drivers can be
built on ARM with COMPILE_TEST && DRM_OMAP.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As warned by Coverity:
CID 1415211 (#1 of 1): Unused value (UNUSED_VALUE)assigned_value:
Assigning value -22 to ret here, but that stored value is
overwritten before it can be used.
On all cases where the there's a goto 'unlock_out' or 'streamof',
ret was filled with a non-sero value. It toesn't make sense to override
such error code with a videobuf_streamoff() error.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Building this driver on arm64 gives this warning:
drivers/media/platform/s5p-jpeg/jpeg-hw-exynos3250.c:430:16: error: return expression in void function
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some VSP instances have two blending units named BRU (Blend/ROP Unit)
and BRS (Blend/ROP Sub unit). The BRS is a smaller version of the BRU
with only two inputs, but otherwise offers similar features and offers
the same register interface. The BRU and BRS can be used exchangeably in
VSP pipelines (provided no more than two inputs are needed).
Due to historical reasons, the VSP1 driver implements support for both
the BRU and BRS through objects named vsp1_bru. The code uses the name
BRU to refer to either the BRU or the BRS, except in a few places where
noted explicitly. This creates confusion.
In an effort to avoid confusion, rename the vsp1_bru object and the
corresponding API to vsp1_brx, and use BRx to refer to blend unit
instances regardless of their type. The names BRU and BRS are retained
where reference to a particular blend unit type is needed, as well as in
hardware registers to stay close to the datasheet.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Dynamic assignment of the BRU and BRS to pipelines is prone to
regressions, add messages to make debugging easier. Keep it as a
separate commit to ease removal of those messages once the code will
deem to be completely stable.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The VSPDL variant drives two DU channels through two LIF and two
blenders, BRU and BRS. The DU channels thus share the five available
VSPDL inputs and expose them as five KMS planes.
The current implementation assigns the BRS to the second LIF and thus
artificially limits the number of planes for the second display channel
to two at most.
Lift this artificial limitation by assigning the BRU and BRS to the
display pipelines on demand based on the number of planes used by each
pipeline. When a display pipeline needs more than two inputs and the BRU
is already in use by the other pipeline, this requires reconfiguring the
other pipeline to free the BRU before processing, which can result in
frame drop on both pipelines.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When disabling a DRM plane, the corresponding RPF is only marked as
removed from the pipeline in the atomic update handler, with the actual
removal happening when configuring the pipeline at atomic commit time.
This is required as the RPF has to be disabled in the hardware, which
can't be done from the atomic update handler.
The current implementation is RPF-specific. Make it independent of the
entity type by using the entity's pipe pointer to mark removal from the
pipeline. This will allow using the mechanism to remove BRU instances.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Display list completion is already reported to the frame end handler,
but that mechanism is global to all display lists. In order to implement
BRU and BRS reassignment in DRM pipelines we will need to commit a
display list and wait for its completion internally, without reporting
it to the DRM driver. Extend the display list API to support such an
internal use of the display list.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We will soon need to return more than a boolean completion status from
the vsp1_dlm_irq_frame_end() IRQ handler. Turn the return value into a
bitfield to prepare for that. No functional change is introduced here.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In order to make the vsp1_du_setup_lif() easier to read, and for
symmetry with the DRM pipeline input setup, move the pipeline output
setup code to a separate function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vsp1_du_setup_lif() function sets up the DRM pipeline input
manually. This duplicates the code from the
vsp1_du_pipeline_setup_inputs() function. Replace the manual
implementation by a call to the function.
As the pipeline has no enabled input in vsp1_du_setup_lif(), the
vsp1_du_pipeline_setup_inputs() function will not setup any RPF, and
will thus not setup formats on the BRU sink pads. This isn't a problem
as all inputs are disabled, and the BRU sink pads will be reconfigured
from the atomic commit handler when inputs will be enabled.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To implement fully dynamic plane assignment to pipelines, we need to
reassign the BRU and BRS to the DRM pipelines in the atomic commit
handler. In preparation for this setup factor out the BRU source pad
code and call it both at LIF setup and atomic commit time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The DRM pipeline setup code used at atomic commit time is similar to the
setup code used when enabling the pipeline. Move it to a separate
function in order to share it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move the duplicated DRM pipeline configuration code to a function and
call it from vsp1_du_setup_lif() and vsp1_du_atomic_flush().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The DRM pipeline handling code uses the entity's pipe list head to check
whether the entity is already included in a pipeline. This method is a
bit fragile in the sense that it uses list_empty() on a list_head that
is a list member. Replace it by a simpler check for the entity pipe
pointer.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Various types of objects subclassing vsp1_entity currently store a
pointer to the pipeline. Move the pointer to vsp1_entity to simplify the
code and avoid storing the pipeline in more entity subclasses later.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vsp1_drm_pipeline enabled field is set but never used. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The DRM support code manages a pipeline of VSP entities, each backed by
a media entity. When starting or stopping the pipeline, it starts and
stops the media pipeline through the media API in order to store the
pipeline pointer in every entity.
The driver doesn't use the pipe pointer in media entities, neither does
it rely on the other effects of the media_pipeline_start() and
media_pipeline_stop() functions. Furthermore, as the media links for the
DRM pipeline are never set up correctly, and as the pipeline can be
modified dynamically when enabling or disabling planes, the current
implementation is not correct. Remove the incorrect and unneeded code.
While at it remove the outdated comment that states that entities are
not started when the LIF is setup, as they now are.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make these const as they are only used as a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only stored in a const field of a
video_device structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There aren't much things required for it to build with COMPILE_TEST.
It just needs to not compile the code that depends on arm-specific
iommu implementation.
Co-developed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The omap3isp driver can't be compiled on non-ARM platforms but has no
compile-time dependency on OMAP. It however requires common clock
framework support, which isn't provided by all ARM platforms.
Drop the OMAP dependency when COMPILE_TEST is set and add ARM and
COMMON_CLK dependencies.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the SoC specific information for Renesas r8a77970.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the SoC specific information for Renesas r8a7796.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the SoC specific information for Renesas r8a7795 ES1.x and ES2.0.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The procedure to start or stop streaming using the non-MC single
subdevice and the MC graph and multiple subdevices are quite different.
Create a new function to abstract which method is used based on which
mode the driver is running in and add logic to start the MC graph.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the ability to process media device link change requests. Link
enabling is a bit complicated on Gen3, whether or not it's possible to
enable a link depends on what other links already are enabled. On Gen3
the 8 VINs are split into two subgroup's (VIN0-3 and VIN4-7) and from a
routing perspective these two groups are independent of each other.
Each subgroup's routing is controlled by the subgroup VIN master
instance (VIN0 and VIN4).
There are a limited number of possible route setups available for each
subgroup and the configuration of each setup is dictated by the
hardware. On H3 for example there are 6 possible route setups for each
subgroup to choose from.
This leads to the media device link notification code being rather large
since it will find the best routing configuration to try and accommodate
as many links as possible. When it's not possible to enable a new link
due to hardware constrains the link_notifier callback will return
-EMLINK.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The parsing and registering CSI-2 subdevices with the v4l2 async
framework is a collaborative effort shared between the VIN instances
which are part of the group. When the last VIN in the group is probed it
asks all other VINs to parse its share of OF and record the async
subdevices it finds in the notifier belonging to the last probed VIN.
Once all CSI-2 subdevices in this notifier are bound proceed to register
all VIN video devices of the group and crate media device links between
all CSI-2 and VIN entities according to the SoC specific routing
configuration.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Each Gen3 SoC has a limited set of predefined routing possibilities for
which CSI-2 device and channel can be routed to which VIN instance.
Prepare to store this information in the struct rvin_info.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The rcar-vin driver needs to be part of a media controller to support
Gen3. Give each VIN instance a unique name so it can be referenced from
userspace.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In media controller mode all VIN instances needs to be part of the same
media graph. There is also a need for each VIN instance to know about
and in some cases be able to communicate with other VIN instances.
Add an allocator framework where the first VIN instance to be probed
creates a shared data structure and registers a media device.
Consecutive VINs insert themself into the global group.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Prepare for media controller by calling a different initialization then
when running in device centric mode. Add trivial configuration of
the mbus and creation of the media pad for the video device entity.
While we are at it clearly mark the digital device centric notifier
functions with a comment.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The V4L2 specification clearly documents the colorspace fields as being
set by drivers for capture devices. Using the values supplied by
userspace thus wouldn't comply with the API. Until the API is updated to
allow for userspace to set these Hans wants the fields to be set by the
driver to fixed values.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the driver runs in media controller mode it should not directly
control the subdevice instead userspace will be responsible for
configuring the pipeline. To be able to run in this mode a different set
of v4l2 operations needs to be used.
Add a new set of v4l2 operations to support operation without directly
interacting with the source subdevice.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On Gen3 a media controller API needs to be used to allow userspace to
configure the subdevices in the pipeline instead of directly controlling
a single source subdevice, which is and will continue to be the mode of
operation on Gen2.
Prepare for these two modes of operation by adding a flag to struct
rvin_info which will control which mode to use.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On Gen3 the CSI-2 routing is controlled by the VnCSI_IFMD register. One
feature of this register is that it's only present in the VIN0 and VIN4
instances. The register in VIN0 controls the routing for VIN0-3 and the
register in VIN4 controls routing for VIN4-7.
To be able to control routing from a media device this function is need
to control runtime PM for the subgroup master (VIN0 and VIN4). The
subgroup master must be switched on before the register is manipulated,
once the operation is complete it's safe to switch the master off and
the new routing will still be in effect.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the register needed to work with Gen3 hardware. This patch adds
the logic for how to work with the Gen3 hardware. More work is required
to enable the subdevice structure needed to configure capturing.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Bus configuration will once the driver is extended to support Gen3
contain information not specific to only the directly connected parallel
subdevice. Move it to struct rvin_dev to show it's not always coupled
to the parallel subdevice.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
At stream on time the driver should not query the subdevice for which
standard are used. Instead it should be cached when userspace sets the
standard and used at stream on time.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With the recent cleanup of the format code to prepare for Gen3 it's
possible to simplify the Gen2 format code path as well. Clean up the
process by defining two functions to handle the set format and reset of
format when the standard is changed.
While at it replace the driver local struct rvin_source_fmt with a
struct v4l2_rect as all it's used for is keep track of the source
dimensions.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Part of the format alignment and checking can be shared with the Gen3
format handling. Break that part out to a separate function.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the pixelformat is not supported it should not fail but be set to
something that works. While we are at it move the two different
checks of the pixelformat to the same statement.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove over complicated logic to calculate the value for bytesperline
and sizeimage that was carried over from the soc_camera port. There is
no need to find the max value of bytesperline and sizeimage from
user-space as they are set to 0 before the max_t() operation.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There was never proper support in the VIN driver to deliver ALTERNATING
field format to user-space, remove this field option. The problem is
that ALTERNATING field order requires the sequence numbers of buffers
returned to userspace to reflect if fields were dropped or not,
something which is not possible with the VIN drivers capture logic.
The VIN driver can still capture from a video source which delivers
frames in ALTERNATING field order, but needs to combine them using the
VIN hardware into INTERLACED field order. Before this change if a source
was delivering fields using ALTERNATE the driver would default to
combining them using this hardware feature. Only if the user explicitly
requested ALTERNATE field order would incorrect frames be delivered.
The height should not be cut in half for the format for TOP or BOTTOM
fields settings. This was a mistake and it was made visible by the
scaling refactoring. Correct behavior is that the user should request a
frame size that fits the half height frame reflected in the field
setting. If not the VIN will do its best to scale the top or bottom to
the requested format and cropping and scaling do not work as expected.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the field is not supported by the driver it should not try to keep
the current field. Instead it should set it to a default fallback. Since
trying a format should always result in the same state regardless of the
current state of the device.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The logic to preserve the requested format width and height are too
complex and come from a premature optimization for Gen3. All Gen2 SoC
can scale and the Gen3 implementation will not use these functions at
all so simply preserve the width and height when interacting with the
subdevice much like the field is preserved simplifies the logic quite a
bit.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation of refactoring the scaling code move the code regarding
scaling to to the top of the file to avoid the need to add forward
declarations. No code is changed in this commit only whole functions
moved inside the same file.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On Gen3 the max supported width and height will be different from Gen2.
Move the limits to the struct rvin_info to prepare for Gen3 support.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
