Commit graph

379 commits

Author SHA1 Message Date
Andy Shevchenko
f63bc78872 bcma: gpio: Switch to use fwnode instead of of_node
GPIO library now accepts fwnode as a firmware node,
so switch the driver to use it.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220504092525.71668-1-andriy.shevchenko@linux.intel.com
2022-05-09 14:41:43 +03:00
Linus Torvalds
e35a4a4e13 Core MTD changes:
* Replace the expert mode symbols with a single helper
 * Fix misuses of of_match_ptr()
 * Remove partid and partname debugfs files
 * tests: Fix eraseblock read speed miscalculation for lower partition sizes
 * TRX parser: Allow to use on MediaTek MIPS SoCs
 
 MTD driver changes:
 * spear_smi: use GFP_KERNEL
 * mchp48l640: Add SPI ID table
 * mchp23k256: Add SPI ID table
 * blkdevs: Avoid soft lockups with some mtd/spi devices
 * aspeed-smc: Improve probe resilience
 
 Hyperbus changes:
 * HBMC_AM654 should depend on ARCH_K3
 
 NAND core changes:
 * ECC:
   - Add infrastructure to support hardware engines
   - Add a new helper to retrieve the ECC context
   - Provide a helper to retrieve a pilelined engine device
 
 NAND-ECC changes:
 * Macronix ECC engine:
   - Add Macronix external ECC engine support
   - Support SPI pipelined mode
   - Make two read-only arrays static const
   - Fix compile test issue
 
 Raw NAND core changes:
 * Fix misuses of of_match_node()
 * Rework of_get_nand_bus_width()
 * Remove of_get_nand_on_flash_bbt() wrapper
 * Protect access to rawnand devices while in suspend
 * bindings: Document the wp-gpios property
 
 Rax NAND controller driver changes:
 * atmel: Fix refcount issue in atmel_nand_controller_init
 * nandsim:
   - Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
   - Merge repeat codes in ns_switch_state
   - Replace overflow check with kzalloc to single kcalloc
 * rockchip: Fix platform_get_irq.cocci warning
 * stm32_fmc2: Add NAND Write Protect support
 * pl353: Set the nand chip node as the flash node
 * brcmnand: Fix sparse warnings in bcma_nand
 * omap_elm: Remove redundant variable 'errors'
 * gpmi:
   - Support fast edo timings for mx28
   - Validate controller clock rate
   - Fix controller timings setting
 * brcmnand:
   - Add BCMA shim
   - BCMA controller uses command shift of 0
   - Allow platform data instantation
   - Add platform data structure for BCMA
   - Allow working without interrupts
   - Move OF operations out of brcmnand_init_cs()
   - Avoid pdev in brcmnand_init_cs()
   - Allow SoC to provide I/O operations
   - Assign soc as early as possible
 
 Onenand changes:
 * Check for error irq
 
 SPI-NAND core changes:
 * Delay a little bit the dirmap creation
 * Create direct mapping descriptors for ECC operations
 
 SPI-NAND driver changes:
 * macronix: Use random program load
 
 SPI NOR core changes:
 * Move vendor specific code out of the core into vendor drivers.
 * Unify all function and object names in the vendor modules.
 * Make setup() callback optional to improve readability.
 * Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
   declaration.
 
 SPI changes:
 * Macronix SPI controller:
   - Fix the transmit path
   - Create a helper to configure the controller before an operation
   - Create a helper to ease the start of an operation
   - Add support for direct mapping
   - Add support for pipelined ECC operations
 * spi-mem:
   - Introduce a capability structure
   - Check the controller extra capabilities
   - cadence-quadspi/mxic: Provide capability structures
   - Kill the spi_mem_dtr_supports_op() helper
   - Add an ecc parameter to the spi_mem_op structure
 
 Binding changes:
 * Dropped mtd/cortina,gemini-flash.txt
 * Convert BCM47xx partitions to json-schema
 * Vendor prefixes: Clarify Macronix prefix
 * SPI NAND: Convert spi-nand description file to yaml
 * Raw NAND chip: Create a NAND chip description
 * Raw NAND controller:
   - Harmonize the property types
   - Fix a comment in the examples
   - Fix the reg property description
 * Describe Macronix NAND ECC engine
 * Macronix SPI controller:
   - Document the nand-ecc-engine property
   - Convert to yaml
   - The interrupt property is not mandatory
 -----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmI7WJcACgkQJWrqGEe9
 VoSzpAgAutzRv9TRUiXdBGGlJ851QaZ6ZUvT1bHKTQA+xZi+MZyNmc0cWNg3B70I
 PnwyxNAmRkUQKwV5Vgy/sQrt42qZnPmr+8XMq+UiziPmgFdjiTdLqGcN619Hi12t
 JqtoKL828R064LSEq5nWsJ2waoGT1nNtZK8kA2qe8ctvmH0YTThriVZUQR4/Befb
 OGFheceLFycE/vkktPPr3As4603fMiyDOT7EA3Mtzgjohry0a0TqoakHCaHC/fYo
 0/h+x+jJATPtgbWm1ZiV3cZ/Su00+rKuQOsiAWvM/pqDaijsVntBmtK0PRtums2Q
 m8LCspuQYNnCINeQXqba9RxACpibDg==
 =+6Zk
 -----END PGP SIGNATURE-----

Merge tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux

Pull MTD updates from Miquel Raynal:
 "There has been a lot of activity in the MTD subsystem recently, with a
  number of SPI-NOR cleanups as well as the introduction of ECC engines
  that can be used by SPI controllers (hence a few SPI patches in here).

  Core MTD changes:
   - Replace the expert mode symbols with a single helper
   - Fix misuses of of_match_ptr()
   - Remove partid and partname debugfs files
   - tests: Fix eraseblock read speed miscalculation for lower partition
     sizes
   - TRX parser: Allow to use on MediaTek MIPS SoCs

  MTD driver changes:
   - spear_smi: use GFP_KERNEL
   - mchp48l640: Add SPI ID table
   - mchp23k256: Add SPI ID table
   - blkdevs: Avoid soft lockups with some mtd/spi devices
   - aspeed-smc: Improve probe resilience

  Hyperbus changes:
   - HBMC_AM654 should depend on ARCH_K3

  NAND core changes:
   - ECC:
      - Add infrastructure to support hardware engines
      - Add a new helper to retrieve the ECC context
      - Provide a helper to retrieve a pilelined engine device

  NAND-ECC changes:
   - Macronix ECC engine:
      - Add Macronix external ECC engine support
      - Support SPI pipelined mode
      - Make two read-only arrays static const
      - Fix compile test issue

  Raw NAND core changes:
   - Fix misuses of of_match_node()
   - Rework of_get_nand_bus_width()
   - Remove of_get_nand_on_flash_bbt() wrapper
   - Protect access to rawnand devices while in suspend
   - bindings: Document the wp-gpios property

  Rax NAND controller driver changes:
   - atmel: Fix refcount issue in atmel_nand_controller_init
   - nandsim:
      - Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
      - Merge repeat codes in ns_switch_state
      - Replace overflow check with kzalloc to single kcalloc
   - rockchip: Fix platform_get_irq.cocci warning
   - stm32_fmc2: Add NAND Write Protect support
   - pl353: Set the nand chip node as the flash node
   - brcmnand: Fix sparse warnings in bcma_nand
   - omap_elm: Remove redundant variable 'errors'
   - gpmi:
      - Support fast edo timings for mx28
      - Validate controller clock rate
      - Fix controller timings setting
   - brcmnand:
      - Add BCMA shim
      - BCMA controller uses command shift of 0
      - Allow platform data instantation
      - Add platform data structure for BCMA
      - Allow working without interrupts
      - Move OF operations out of brcmnand_init_cs()
      - Avoid pdev in brcmnand_init_cs()
      - Allow SoC to provide I/O operations
      - Assign soc as early as possible

  Onenand changes:
   - Check for error irq

  SPI-NAND core changes:
   - Delay a little bit the dirmap creation
   - Create direct mapping descriptors for ECC operations

  SPI-NAND driver changes:
   - macronix: Use random program load

  SPI NOR core changes:
   - Move vendor specific code out of the core into vendor drivers.
   - Unify all function and object names in the vendor modules.
   - Make setup() callback optional to improve readability.
   - Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
     declaration.

  SPI changes:
   - Macronix SPI controller:
      - Fix the transmit path
      - Create a helper to configure the controller before an operation
      - Create a helper to ease the start of an operation
      - Add support for direct mapping
      - Add support for pipelined ECC operations
   - spi-mem:
      - Introduce a capability structure
      - Check the controller extra capabilities
      - cadence-quadspi/mxic: Provide capability structures
      - Kill the spi_mem_dtr_supports_op() helper
      - Add an ecc parameter to the spi_mem_op structure

  Binding changes:
   - Dropped mtd/cortina,gemini-flash.txt
   - Convert BCM47xx partitions to json-schema
   - Vendor prefixes: Clarify Macronix prefix
   - SPI NAND: Convert spi-nand description file to yaml
   - Raw NAND chip: Create a NAND chip description
   - Raw NAND controller:
      - Harmonize the property types
      - Fix a comment in the examples
      - Fix the reg property description
   - Describe Macronix NAND ECC engine
   - Macronix SPI controller:
      - Document the nand-ecc-engine property
      - Convert to yaml
      - The interrupt property is not mandatory"

* tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits)
  mtd: nand: ecc: mxic: Fix compile test issue
  mtd: nand: mxic-ecc: make two read-only arrays static const
  mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3
  mtd: core: Remove partid and partname debugfs files
  dt-bindings: mtd: partitions: convert BCM47xx to the json-schema
  mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes
  mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
  mtd: rawnand: rockchip: fix platform_get_irq.cocci warning
  mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
  mtd: spi-nor: renumber flags
  mtd: spi-nor: slightly change code style in spi_nor_sr_ready()
  mtd: spi-nor: spansion: rename vendor specific functions and defines
  mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag
  mtd: spi-nor: move all spansion specifics into spansion.c
  mtd: spi-nor: spansion: slightly rework control flow in late_init()
  mtd: spi-nor: micron-st: rename vendor specific functions and defines
  mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag
  mtd: spi-nor: move all micron-st specifics into micron-st.c
  mtd: spi-nor: xilinx: correct the debug message
  mtd: spi-nor: xilinx: rename vendor specific functions and defines
  ...
2022-03-25 13:35:34 -07:00
Colin Ian King
857f837d85 bcma: gpio: remove redundant re-assignment of chip->owner
There are two identical assignments of chip->owner to the same value,
the second assignment is redundant and can be removed.

Cleans up cppcheck warning:
drivers/bcma/driver_gpio.c:184:15: style: Variable 'chip->owner' is
reassigned a value before the old one has been used. [redundantAssignment]

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220303085841.1124766-1-colin.i.king@gmail.com
2022-03-10 18:17:53 +02:00
Tom Rix
032931fdd5 bcma: cleanup comments
Remove the second 'info'.
Replacements
'adventages' with 'advantages'
'strenth' with 'strength'
'atleast' with 'at least'
'thr'u'' with 'through'
'capabilty' with 'capability'
'controll' with 'control'
'ourself' with 'ourselves'
'noone' with 'no one'
'cores' to 'core's' and 'core'

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220213213121.2806376-1-trix@redhat.com
2022-02-21 10:58:14 +02:00
Florian Fainelli
02d1d0e4df mtd: rawnand: brcmnand: Add platform data structure for BCMA
Update the BCMA's chipcommon nand flash driver to detect which
chip-select is used and pass that information via platform data to the
brcmnand driver. Make sure that the brcmnand platform data structure is
always at the beginning of the platform data of the "nflash" device
created by BCMA to allow brcmnand to safely de-reference it.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-7-f.fainelli@gmail.com
2022-01-23 16:37:18 +01:00
Linus Torvalds
0c5c62ddf8 pci-v5.16-changes
-----BEGIN PGP SIGNATURE-----
 
 iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmGFXBkUHGJoZWxnYWFz
 QGdvb2dsZS5jb20ACgkQWYigwDrT+vx6Tg/7BsGWm8f+uw/mr9lLm47q2mc4XyoO
 7bR9KDp5NM84W/8ZOU7dqqqsnY0ddrSOLBRyhJJYMW3SwJd1y1ajTBsL1Ujqv+eN
 z+JUFmhq4Laqm4k6Spc9CEJE+Ol5P6gGUtxLYo6PM2R0VxnSs/rDxctT5i7YOpCi
 COJ+NVT/mc/by2loz1kLTSR9GgtBBgd+Y8UA33GFbHKssROw02L0OI3wffp81Oba
 EhMGPoD+0FndAniDw+vaOSoO+YaBuTfbM92T/O00mND69Fj1PWgmNWZz7gAVgsXb
 3RrNENUFxgw6CDt7LZWB8OyT04iXe0R2kJs+PA9gigFCGbypwbd/Nbz5M7e9HUTR
 ray+1EpZib6+nIksQBL2mX8nmtyHMcLiM57TOEhq0+ECDO640MiRm8t0FIG/1E8v
 3ZYd9w20o/NxlFNXHxxpZ3D/osGH5ocyF5c5m1rfB4RGRwztZGL172LWCB0Ezz9r
 eHB8sWxylxuhrH+hp2BzQjyddg7rbF+RA4AVfcQSxUpyV01hoRocKqknoDATVeLH
 664nJIINFxKJFwfuL3E6OhrInNe1LnAhCZsHHqbS+NNQFgvPRznbixBeLkI9dMf5
 Yf6vpsWO7ur8lHHbRndZubVu8nxklXTU7B/w+C11sq6k9LLRJSHzanr3Fn9WA80x
 sznCxwUvbTCu1r0=
 =nsMh
 -----END PGP SIGNATURE-----

Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

Pull pci updates from Bjorn Helgaas:
 "Enumeration:
   - Conserve IRQs by setting up portdrv IRQs only when there are users
     (Jan Kiszka)
   - Rework and simplify _OSC negotiation for control of PCIe features
     (Joerg Roedel)
   - Remove struct pci_dev.driver pointer since it's redundant with the
     struct device.driver pointer (Uwe Kleine-König)

  Resource management:
   - Coalesce contiguous host bridge apertures from _CRS to accommodate
     BARs that cover more than one aperture (Kai-Heng Feng)

  Sysfs:
   - Check CAP_SYS_ADMIN before parsing user input (Krzysztof
     Wilczyński)
   - Return -EINVAL consistently from "store" functions (Krzysztof
     Wilczyński)
   - Use sysfs_emit() in endpoint "show" functions to avoid buffer
     overruns (Kunihiko Hayashi)

  PCIe native device hotplug:
   - Ignore Link Down/Up caused by resets during error recovery so
     endpoint drivers can remain bound to the device (Lukas Wunner)

  Virtualization:
   - Avoid bus resets on Atheros QCA6174, where they hang the device
     (Ingmar Klein)
   - Work around Pericom PI7C9X2G switch packet drop erratum by using
     store and forward mode instead of cut-through (Nathan Rossi)
   - Avoid trying to enable AtomicOps on VFs; the PF setting applies to
     all VFs (Selvin Xavier)

  MSI:
   - Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
     interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
     Song)

  VPD:
   - Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
     in the possible VPD space; use these to simplify the cxgb3 driver
     (Heiner Kallweit)

  Peer-to-peer DMA:
   - Add (not subtract) the bus offset when calculating DMA address
     (Wang Lu)

  ASPM:
   - Re-enable LTR at Downstream Ports so they don't report Unsupported
     Requests when reset or hot-added devices send LTR messages
     (Mingchuang Qiao)

  Apple PCIe controller driver:
   - Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
     Zyngier)

  Cadence PCIe controller driver:
   - Return success when probe succeeds instead of falling into error
     path (Li Chen)

  HiSilicon Kirin PCIe controller driver:
   - Reorganize PHY logic and add support for external PHY drivers
     (Mauro Carvalho Chehab)
   - Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
     Carvalho Chehab)
   - Add Kirin 970 support (Mauro Carvalho Chehab)
   - Make driver removable (Mauro Carvalho Chehab)

  Intel VMD host bridge driver:
   - If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
     enabled (Adrian Huang)
   - Number each controller so we can tell them apart in
     /proc/interrupts (Chunguang Xu)
   - Avoid building on UML because VMD depends on x86 bare metal APIs
     (Johannes Berg)

  Marvell Aardvark PCIe controller driver:
   - Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
   - Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
   - Downgrade PIO Response Status messages to debug level (Marek Behún)
   - Preserve CRS SV (Config Request Retry Software Visibility) bit in
     emulated Root Control register (Pali Rohár)
   - Fix issue in configuring reference clock (Pali Rohár)
   - Don't clear status bits for masked interrupts (Pali Rohár)
   - Don't mask unused interrupts (Pali Rohár)
   - Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
   - Retry config accesses on CRS response (Pali Rohár)
   - Simplify emulated Root Capabilities initialization (Pali Rohár)
   - Fix several link training issues (Pali Rohár)
   - Fix link-up checking via LTSSM (Pali Rohár)
   - Fix reporting of Data Link Layer Link Active (Pali Rohár)
   - Fix emulation of W1C bits (Marek Behún)
   - Fix MSI domain .alloc() method to return zero on success (Marek
     Behún)
   - Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
     (Marek Behún)
   - Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
     at startup; PCI core will set those as necessary (Pali Rohár)
   - When operating as a Root Port, set class code to "PCI Bridge"
     instead of the default "Mass Storage Controller" (Pali Rohár)
   - Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
     implement this per spec (Pali Rohár)
   - Add emulation of option ROM BAR since aardvark doesn't implement
     this per spec (Pali Rohár)

  MediaTek MT7621 PCIe controller driver:
   - Add MediaTek MT7621 PCIe host controller driver and DT binding
     (Sergio Paracuellos)

  Qualcomm PCIe controller driver:
   - Add SC8180x compatible string (Bjorn Andersson)
   - Add endpoint controller driver and DT binding (Manivannan
     Sadhasivam)
   - Restructure to use of_device_get_match_data() (Prasad Malisetty)
   - Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)

  Renesas R-Car PCIe controller driver:
   - Remove unnecessary includes (Geert Uytterhoeven)

  Rockchip DesignWare PCIe controller driver:
   - Add DT binding (Simon Xue)

  Socionext UniPhier Pro5 controller driver:
   - Serialize INTx masking/unmasking (Kunihiko Hayashi)

  Synopsys DesignWare PCIe controller driver:
   - Run dwc .host_init() method before registering MSI interrupt
     handler so we can deal with pending interrupts left by bootloader
     (Bjorn Andersson)
   - Clean up Kconfig dependencies (Andy Shevchenko)
   - Export symbols to allow more modular drivers (Luca Ceresoli)

  TI DRA7xx PCIe controller driver:
   - Allow host and endpoint drivers to be modules (Luca Ceresoli)
   - Enable external clock if present (Luca Ceresoli)

  TI J721E PCIe driver:
   - Disable PHY when probe fails after initializing it (Christophe
     JAILLET)

  MicroSemi Switchtec management driver:
   - Return error to application when command execution fails because an
     out-of-band reset has cleared the device BARs, Memory Space Enable,
     etc (Kelvin Cao)
   - Fix MRPC error status handling issue (Kelvin Cao)
   - Mask out other bits when reading of management VEP instance ID
     (Kelvin Cao)
   - Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
     (Kelvin Cao)
   - Add check of event support (Logan Gunthorpe)

  Miscellaneous:
   - Remove unused pci_pool wrappers, which have been replaced by
     dma_pool (Cai Huoqing)
   - Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
     Wilczyński)
   - Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
     Wilczyński)
   - Fix some sscanf(), sprintf() format mismatches (Krzysztof
     Wilczyński)
   - Update PCI subsystem information in MAINTAINERS (Krzysztof
     Wilczyński)
   - Correct some misspellings (Krzysztof Wilczyński)"

* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
  PCI: Add ACS quirk for Pericom PI7C9X2G switches
  PCI: apple: Configure RID to SID mapper on device addition
  iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
  PCI: apple: Implement MSI support
  PCI: apple: Add INTx and per-port interrupt support
  PCI: kirin: Allow removing the driver
  PCI: kirin: De-init the dwc driver
  PCI: kirin: Disable clkreq during poweroff sequence
  PCI: kirin: Move the power-off code to a common routine
  PCI: kirin: Add power_off support for Kirin 960 PHY
  PCI: kirin: Allow building it as a module
  PCI: kirin: Add MODULE_* macros
  PCI: kirin: Add Kirin 970 compatible
  PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
  PCI: apple: Set up reference clocks when probing
  PCI: apple: Add initial hardware bring-up
  PCI: of: Allow matching of an interrupt-map local to a PCI device
  of/irq: Allow matching of an interrupt-map local to an interrupt controller
  irqdomain: Make of_phandle_args_to_fwspec() generally available
  PCI: Do not enable AtomicOps on VFs
  ...
2021-11-06 14:36:12 -07:00
Uwe Kleine-König
823c523eb2 bcma: simplify reference to driver name
When bcma_host_pci_probe() is called, the PCI driver core has already
assigned the device's driver in local_pci_probe(). So dev->driver is always
true, and here it points to bcma_pci_bridge_driver, which has .name set to
"bcma-pci-bridge". Simplify accordingly.

Link: https://lore.kernel.org/r/20211004125935.2300113-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2021-10-12 17:50:12 -05:00
Sohaib Mohamed
5668958f6a bcma: drop unneeded initialization value
Do not initialise statics to 0
ERROR found by checkpatch.pl

Signed-off-by: Sohaib Mohamed <sohaib.amhmd@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210930194920.15847-1-sohaib.amhmd@gmail.com
2021-10-05 08:32:30 +03:00
Linus Torvalds
c6c3c5704b Driver core update for 5.15-rc1
Here is the big set of driver core patches for 5.15-rc1.
 
 These do change a number of different things across different
 subsystems, and because of that, there were 2 stable tags created that
 might have already come into your tree from different pulls that did the
 following
 	- changed the bus remove callback to return void
 	- sysfs iomem_get_mapping rework
 
 The latter one will cause a tiny merge issue with your tree, as there
 was a last-minute fix for this in 5.14 in your tree, but the fixup
 should be "obvious".  If you want me to provide a fixed merge for this,
 please let me know.
 
 Other than those two things, there's only a few small things in here:
 	- kernfs performance improvements for huge numbers of sysfs
 	  users at once
 	- tiny api cleanups
 	- other minor changes
 
 All of these have been in linux-next for a while with no reported
 problems, other than the before-mentioned merge issue.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+FLQ8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ylXuACfWECnysDtXNe66DdETCFs1a1RToYAoMokWeU5
 s8VFP1NY2BjmxJbkebLL
 =8kVu
 -----END PGP SIGNATURE-----

Merge tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core updates from Greg KH:
 "Here is the big set of driver core patches for 5.15-rc1.

  These do change a number of different things across different
  subsystems, and because of that, there were 2 stable tags created that
  might have already come into your tree from different pulls that did
  the following

   - changed the bus remove callback to return void

   - sysfs iomem_get_mapping rework

  Other than those two things, there's only a few small things in here:

   - kernfs performance improvements for huge numbers of sysfs users at
     once

   - tiny api cleanups

   - other minor changes

  All of these have been in linux-next for a while with no reported
  problems, other than the before-mentioned merge issue"

* tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits)
  MAINTAINERS: Add dri-devel for component.[hc]
  driver core: platform: Remove platform_device_add_properties()
  ARM: tegra: paz00: Handle device properties with software node API
  bitmap: extend comment to bitmap_print_bitmask/list_to_buf
  drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI
  topology: use bin_attribute to break the size limitation of cpumap ABI
  lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases
  cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list
  sysfs: Rename struct bin_attribute member to f_mapping
  sysfs: Invoke iomem_get_mapping() from the sysfs open callback
  debugfs: Return error during {full/open}_proxy_open() on rmmod
  zorro: Drop useless (and hardly used) .driver member in struct zorro_dev
  zorro: Simplify remove callback
  sh: superhyway: Simplify check in remove callback
  nubus: Simplify check in remove callback
  nubus: Make struct nubus_driver::remove return void
  kernfs: dont call d_splice_alias() under kernfs node lock
  kernfs: use i_lock to protect concurrent inode updates
  kernfs: switch kernfs to use an rwsem
  kernfs: use VFS negative dentry caching
  ...
2021-09-01 08:44:42 -07:00
Zenghui Yu
9fc8048c56 bcma: Drop the unused parameter of bcma_scan_read32()
As it had never been used since the initial commit 8369ae33b7 ("bcma: add
Broadcom specific AMBA bus driver").

Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210727025232.663-3-yuzenghui@huawei.com
2021-08-29 14:44:57 +03:00
Zenghui Yu
b63aed3ff1 bcma: Fix memory leak for internally-handled cores
kmemleak reported that dev_name() of internally-handled cores were leaked
on driver unbinding. Let's use device_initialize() to take refcounts for
them and put_device() to properly free the related stuff.

While looking at it, there's another potential issue for those which should
be *registered* into driver core. If device_register() failed, we put
device once and freed bcma_device structures. In bcma_unregister_cores(),
they're treated as unregistered and we hit both UAF and double-free. That
smells not good and has also been fixed now.

Fixes: ab54bc8460 ("bcma: fill core details for every device")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210727025232.663-2-yuzenghui@huawei.com
2021-08-29 14:44:57 +03:00
Uwe Kleine-König
fc7a6209d5 bus: Make remove callback return void
The driver core ignores the return value of this callback because there
is only little it can do when a device disappears.

This is the final bit of a long lasting cleanup quest where several
buses were converted to also return void from their remove callback.
Additionally some resource leaks were fixed that were caused by drivers
returning an error code in the expectation that the driver won't go
away.

With struct bus_type::remove returning void it's prevented that newly
implemented buses return an ignored error code and so don't anticipate
wrong expectations for driver authors.

Reviewed-by: Tom Rix <trix@redhat.com> (For fpga)
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio)
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts)
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media)
Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform)
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com> (For xen)
Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd)
Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb)
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus)
Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio)
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec)
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack)
Acked-by: Geoff Levand <geoff@infradead.org> (For ps3)
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt)
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th)
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia)
Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI)
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr)
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid)
Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM)
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa)
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire)
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid)
Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox)
Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss)
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC)
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-07-21 11:53:42 +02:00
Jiapeng Chong
fa84df7052 bcma: remove unused function
Fix the following clang warning:

drivers/bcma/driver_mips.c:55:20: warning: unused function
'mips_write32' [-Wunused-function].

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1618382354-866-1-git-send-email-jiapeng.chong@linux.alibaba.com
2021-04-18 09:36:56 +03:00
Julia Lawall
703314b2db bcma: use semicolons rather than commas to separate statements
Replace commas with semicolons.  What is done is essentially described by
the following Coccinelle semantic patch (http://coccinelle.lip6.fr/):

// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601233948-11629-6-git-send-email-Julia.Lawall@inria.fr
2020-10-01 16:23:50 +03:00
Linus Walleij
a080ecb11a bcma: gpio: Use irqchip template
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().

The irqchip is instead added while adding the gpiochip.

Cc: Rafał Miłecki <rafal@milecki.pl>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200722111725.210923-1-linus.walleij@linaro.org
2020-08-02 18:26:51 +03:00
Zheng Yongjun
92d26d1abf drivers: bcma: remove set but not used variable addrh and sizeh
Fixes gcc '-Wunused-but-set-variable' warning:

drivers/bcma/scan.c: In function 'bcma_erom_get_addr_desc':
drivers/bcma/scan.c:219 warning:
variable `addrh` and `sizeh` set but not used [-Wunused-but-set-variable]

Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200721083935.13306-1-zhengyongjun3@huawei.com
2020-08-02 18:26:18 +03:00
Linus Torvalds
bd2463ac7d Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from David Miller:

 1) Add WireGuard

 2) Add HE and TWT support to ath11k driver, from John Crispin.

 3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.

 4) Add variable window congestion control to TIPC, from Jon Maloy.

 5) Add BCM84881 PHY driver, from Russell King.

 6) Start adding netlink support for ethtool operations, from Michal
    Kubecek.

 7) Add XDP drop and TX action support to ena driver, from Sameeh
    Jubran.

 8) Add new ipv4 route notifications so that mlxsw driver does not have
    to handle identical routes itself. From Ido Schimmel.

 9) Add BPF dynamic program extensions, from Alexei Starovoitov.

10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.

11) Add support for macsec HW offloading, from Antoine Tenart.

12) Add initial support for MPTCP protocol, from Christoph Paasch,
    Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.

13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
    Cherian, and others.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
  net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
  udp: segment looped gso packets correctly
  netem: change mailing list
  qed: FW 8.42.2.0 debug features
  qed: rt init valid initialization changed
  qed: Debug feature: ilt and mdump
  qed: FW 8.42.2.0 Add fw overlay feature
  qed: FW 8.42.2.0 HSI changes
  qed: FW 8.42.2.0 iscsi/fcoe changes
  qed: Add abstraction for different hsi values per chip
  qed: FW 8.42.2.0 Additional ll2 type
  qed: Use dmae to write to widebus registers in fw_funcs
  qed: FW 8.42.2.0 Parser offsets modified
  qed: FW 8.42.2.0 Queue Manager changes
  qed: FW 8.42.2.0 Expose new registers and change windows
  qed: FW 8.42.2.0 Internal ram offsets modifications
  MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
  Documentation: net: octeontx2: Add RVU HW and drivers overview
  octeontx2-pf: ethtool RSS config support
  octeontx2-pf: Add basic ethtool support
  ...
2020-01-28 16:02:33 -08:00
Christoph Hellwig
4bdc0d676a remove ioremap_nocache and devm_ioremap_nocache
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
2020-01-06 09:45:59 +01:00
yu kuai
f427939391 bcma: remove set but not used variable 'sizel'
Fixes gcc '-Wunused-but-set-variable' warning:

drivers/bcma/scan.c: In function ‘bcma_erom_get_addr_desc’:

drivers/bcma/scan.c:222:20: warning: variable ‘sizel’ set but
not used [-Wunused-but-set-variable]

It is never used, and so can be removed.

Fixes: 8369ae33b7 ("bcma: add Broadcom specific AMBA bus driver")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-12-18 20:55:25 +02:00
Yadav Lamichhane
844e9d7c60 bcma: fix block comment style
Fix a coding style issue.

Signed-off-by: Yadav Lamichhane <tuxomega1@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-10-24 08:45:31 +03:00
Colin Ian King
c57391f415 bcma: make arrays pwr_info_offset and sprom_sizes static const, shrinks object size
Arrays pwr_info_offset and sprom_sizes can be make static const rather
than populating them on the stack. Shrinks object size by 236 bytes.

Before:
   text	   data	    bss	    dec	    hex	filename
  11300	   1320	     64	  12684	   318c	drivers/bcma/sprom.o

After:
   text	   data	    bss	    dec	    hex	filename
  10904	   1480	     64	  12448	   30a0	drivers/bcma/sprom.o

(gcc version 9.2.1, amd64)

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-09-13 16:44:49 +03:00
Colin Ian King
420c20be08 bcma: fix incorrect update of BCMA_CORE_PCI_MDIO_DATA
An earlier commit re-worked the setting of the bitmask and is now
assigning v with some bit flags rather than bitwise or-ing them
into v, consequently the earlier bit-settings of v are being lost.
Fix this by replacing an assignment with the bitwise or instead.

Addresses-Coverity: ("Unused value")
Fixes: 2be25cac84 ("bcma: add constants for PCI and use them")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-09-03 16:44:02 +03:00
YueHaibing
0a60e0aa49 bcma: remove two unused variables
drivers/bcma/driver_mips.c:70:18: warning:
 ipsflag_irq_shift defined but not used [-Wunused-const-variable=]
drivers/bcma/driver_mips.c:62:18: warning:
 ipsflag_irq_mask defined but not used [-Wunused-const-variable=]

They are never used, so can be removed.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-09-03 16:37:53 +03:00
Chuhong Yuan
9236c1250c bcma: Use dev_get_drvdata
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-08-06 15:25:28 +03:00
Rafał Miłecki
777bc4801a bcma: use dev_* printing functions
It provides more meaningful messages.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-01-10 13:39:19 +02:00
Rafał Miłecki
5a1c18b761 bcma: keep a direct pointer to the struct device
Accessing struct device is pretty useful/common so having a direct
pointer:
1) Simplifies some code
2) Makes bcma_bus_get_host_dev() unneeded
3) Allows further improvements like using dev_* printing helpers

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-01-10 13:39:18 +02:00
Boris Brezillon
a58d0b4d51 bcma: Allow selection of this driver when COMPILE_TEST=y
This allows us to increase compile-test coverage without having to build
a kernel for MIPS.  That's particularly interesting for subsystem
maintainers that want to test as many drivers as possible in a single
build.

We also add a dependency on HAS_IOMEM in BCMA_HOST_SOC to make sure the
driver is not selected when the arch does not implement IO accessors.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-07-18 09:34:19 +02:00
Linus Torvalds
e5a594643a dma-mapping updates for 4.18:
- replaceme the force_dma flag with a dma_configure bus method.
    (Nipun Gupta, although one patch is іncorrectly attributed to me
     due to a git rebase bug)
  - use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
  - remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
    right thing for bounce buffering.
  - move dma-debug initialization to common code, and apply a few cleanups
    to the dma-debug code.
  - cleanup the Kconfig mess around swiotlb selection
  - swiotlb comment fixup (Yisheng Xie)
  - a trivial swiotlb fix. (Dan Carpenter)
  - support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
  - add a new generic dma-noncoherent dma_map_ops implementation and use
    it for arc, c6x and nds32.
  - improve scatterlist validity checking in dma-debug. (Robin Murphy)
  - add a struct device quirk to limit the dma-mask to 32-bit due to
    bridge/system issues, and switch x86 to use it instead of a local
    hack for VIA bridges.
  - handle devices without a dma_mask more gracefully in the dma-direct
    code.
 -----BEGIN PGP SIGNATURE-----
 
 iQI/BAABCAApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAlsU1hwLHGhjaEBsc3Qu
 ZGUACgkQD55TZVIEUYPraxAAocC7JiFKW133/VugCtGA1x9uE8DPHealtsWTAeEq
 KOOB3GxWMU2hKqQ4km5tcfdWoGJvvab6hmDXcitzZGi2JajO7Ae0FwIy3yvxSIKm
 iH/ON7c4sJt8gKrXYsLVylmwDaimNs4a6xfODoCRgnWuovI2QrrZzupnlzPNsiOC
 lv8ezzcW+Ay/gvDD/r72psO+w3QELETif/OzR/qTOtvLrVabM06eHmPQ8Wb98smu
 /UPMMv6/3XwQnxpxpdyqN+p/gUdneXithzT261wTeZ+8gDXmcWBwHGcMBCimcoBi
 FklW52moazIPIsTysqoNlVFsLGJTeS4p2D3BLAp5NwWYsLv+zHUVZsI1JY/8u5Ox
 mM11LIfvu9JtUzaqD9SvxlxIeLhhYZZGnUoV3bQAkpHSQhN/xp2YXd5NWSo5ac2O
 dch83+laZkZgd6ryw6USpt/YTPM/UHBYy7IeGGHX/PbmAke0ZlvA6Rae7kA5DG59
 7GaLdwQyrHp8uGFgwze8P+R4POSk1ly73HHLBT/pFKnDD7niWCPAnBzuuEQGJs00
 0zuyWLQyzOj1l6HCAcMNyGnYSsMp8Fx0fvEmKR/EYs8O83eJKXi6L9aizMZx4v1J
 0wTolUWH6SIIdz474YmewhG5YOLY7mfe9E8aNr8zJFdwRZqwaALKoteRGUxa3f6e
 zUE=
 =6Acj
 -----END PGP SIGNATURE-----

Merge tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping

Pull dma-mapping updates from Christoph Hellwig:

 - replace the force_dma flag with a dma_configure bus method. (Nipun
   Gupta, although one patch is іncorrectly attributed to me due to a
   git rebase bug)

 - use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)

 - remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
   right thing for bounce buffering.

 - move dma-debug initialization to common code, and apply a few
   cleanups to the dma-debug code.

 - cleanup the Kconfig mess around swiotlb selection

 - swiotlb comment fixup (Yisheng Xie)

 - a trivial swiotlb fix. (Dan Carpenter)

 - support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)

 - add a new generic dma-noncoherent dma_map_ops implementation and use
   it for arc, c6x and nds32.

 - improve scatterlist validity checking in dma-debug. (Robin Murphy)

 - add a struct device quirk to limit the dma-mask to 32-bit due to
   bridge/system issues, and switch x86 to use it instead of a local
   hack for VIA bridges.

 - handle devices without a dma_mask more gracefully in the dma-direct
   code.

* tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping: (48 commits)
  dma-direct: don't crash on device without dma_mask
  nds32: use generic dma_noncoherent_ops
  nds32: implement the unmap_sg DMA operation
  nds32: consolidate DMA cache maintainance routines
  x86/pci-dma: switch the VIA 32-bit DMA quirk to use the struct device flag
  x86/pci-dma: remove the explicit nodac and allowdac option
  x86/pci-dma: remove the experimental forcesac boot option
  Documentation/x86: remove a stray reference to pci-nommu.c
  core, dma-direct: add a flag 32-bit dma limits
  dma-mapping: remove unused gfp_t parameter to arch_dma_alloc_attrs
  dma-debug: check scatterlist segments
  c6x: use generic dma_noncoherent_ops
  arc: use generic dma_noncoherent_ops
  arc: fix arc_dma_{map,unmap}_page
  arc: fix arc_dma_sync_sg_for_{cpu,device}
  arc: simplify arc_dma_sync_single_for_{cpu,device}
  dma-mapping: provide a generic dma-noncoherent implementation
  dma-mapping: simplify Kconfig dependencies
  riscv: add swiotlb support
  riscv: only enable ZONE_DMA32 for 64-bit
  ...
2018-06-04 10:58:12 -07:00
Rafał Miłecki
361de091a4 bcma: fix buffer size caused crash in bcma_core_mips_print_irq()
Used buffer wasn't big enough to hold whole strings. Example output of
this function is:
[    0.180892] bcma: bus0: core 0x0800, irq: 2(S)* 3  4  5  6  D  I
[    0.180948] bcma: bus0: core 0x0812, irq: 2(S)  3* 4  5  6  D  I
[    0.180998] bcma: bus0: core 0x082d, irq: 2(S)  3  4* 5  6  D  I
[    0.181046] bcma: bus0: core 0x082c, irq: 2(S)  3  4  5  6  D  I*
which means we need to store up to 24 chars.

Fixes: 758f7e0606 ("bcma: Use bcma_debug and not pr_cont in MIPS driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-12 11:36:59 +03:00
Christoph Hellwig
3d6ce86ee7 drivers: remove force dma flag from buses
With each bus implementing its own DMA configuration callback, there is no
need for bus to explicitly set the force_dma flag.  Modify the
of_dma_configure function to accept an input parameter which specifies if
implicit DMA configuration is required when it is not described by the
firmware.

Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>  # PCI parts
Reviewed-by: Rob Herring <robh@kernel.org>
[hch: tweaked the changelog a bit]
Signed-off-by: Christoph Hellwig <hch@lst.de>
2018-05-03 16:25:08 +02:00
Matt Redfearn
79ca239a68 bcma: Prevent build of PCI host features in module
Attempting to build bcma.ko with BCMA_DRIVER_PCI_HOSTMODE=y results in
a build error due to use of symbols not exported from vmlinux:

ERROR: "pcibios_enable_device" [drivers/bcma/bcma.ko] undefined!
ERROR: "register_pci_controller" [drivers/bcma/bcma.ko] undefined!
make[1]: *** [scripts/Makefile.modpost:92: __modpost] Error 1

To prevent this, don't allow the host mode feature to be built if
CONFIG_BCMA=m

Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-03-13 18:47:47 +02:00
Denis 'GNUtoo' Carikli
985324a16e bcma: add HP Stream Notebook
In this laptop we have the following PCI device:
02:00.0 Network controller [0280]: Broadcom Limited BCM43142 802.11b/g/n [14e4:4365] (rev 01)
	Subsystem: Hewlett-Packard Company BCM43142 802.11b/g/n [103c:804a]
	[...]
	Region 0: Memory at 91000000 (64-bit, non-prefetchable) [size=32K]
	[...]

With this patch, we can now see its WiFi chip:
  bcma: bus0: Found chip with id 43142, rev 0x01 and package 0x08
  bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x28, class 0x0)
  bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x21, class 0x0)
  bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x16, class 0x0)
  bcma: bus0: Core 3 found: UNKNOWN (manuf 0x43B, id 0x368, rev 0x00, class 0x0)
  bcma: bus0: Found rev 15 PMU (capabilities 0x518C5E0F)
  bcma: bus0: SPROM offset 0x840
  bcma: bus0: Found SPROM revision 10
  bcma: bus0: Workarounds unknown or not needed for device 0xA886
  bcma: bus0: Bus registered

But it not yet supported by brcmsmac so it won't work for now:
  brcmsmac bcma0:1: brcms_b_attach wl0: vendor 0x14e4 device 0x4365
  brcmsmac: unknown device id 4365

Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-02-28 16:37:22 +02:00
Jia-Ju Bai
8100091d02 bcma: Replace mdelay with usleep_range in bcma_pmu_resources_init
After checking all possible call chains to bcma_pmu_resources_init() here,
my tool finds that this function is never called in atomic context,
namely never in an interrupt handler or holding a spinlock.
Thus mdelay can be replaced with usleep_range to avoid busy wait.

This is found by a static analysis tool named DCNS written by myself.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-02-27 15:52:13 +02:00
David S. Miller
8565d26bcb Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
The BPF verifier conflict was some minor contextual issue.

The TUN conflict was less trivial.  Cong Wang fixed a memory leak of
tfile->tx_array in 'net'.  This is an skb_array.  But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-19 22:59:33 -05:00
Guenter Roeck
664eadd6f4 bcma: Fix 'allmodconfig' and BCMA builds on MIPS targets
Mips builds with BCMA host mode enabled fail in mainline and -next
with:

In file included from include/linux/bcma/bcma.h:10:0,
                 from drivers/bcma/bcma_private.h:9,
		 from drivers/bcma/main.c:8:
include/linux/bcma/bcma_driver_pci.h:218:24: error:
	field 'pci_controller' has incomplete type

Bisect points to commit d41e6858ba ("MIPS: Kconfig: Set default MIPS
system type as generic") as the culprit. Analysis shows that the commmit
changes PCI configuration and enables PCI_DRIVERS_GENERIC. This in turn
disables PCI_DRIVERS_LEGACY. 'struct pci_controller' is, however, only
defined if PCI_DRIVERS_LEGACY is enabled.

Ultimately that means that BCMA_DRIVER_PCI_HOSTMODE depends on
PCI_DRIVERS_LEGACY. Add the missing dependency.

Fixes: d41e6858ba ("MIPS: Kconfig: Set default MIPS system type as ...")
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: James Hogan <jhogan@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-16 21:13:55 +02:00
Ashish Kalra
a765c8fdc8 bcma: Adjust block comment
use * for block comments in multiple lines according to kernel coding
style

Reported by: checkpatch.pl

Signed-off-by: Ashish Kalra <eashishkalra@gmail.com>
Reviewed-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-12-07 15:33:02 +02:00
Linus Torvalds
5bbcc0f595 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:
 "Highlights:

   1) Maintain the TCP retransmit queue using an rbtree, with 1GB
      windows at 100Gb this really has become necessary. From Eric
      Dumazet.

   2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.

   3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
      Lunn.

   4) Add meter action support to openvswitch, from Andy Zhou.

   5) Add a data meta pointer for BPF accessible packets, from Daniel
      Borkmann.

   6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.

   7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.

   8) More work to move the RTNL mutex down, from Florian Westphal.

   9) Add 'bpftool' utility, to help with bpf program introspection.
      From Jakub Kicinski.

  10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
      Dangaard Brouer.

  11) Support 'blocks' of transformations in the packet scheduler which
      can span multiple network devices, from Jiri Pirko.

  12) TC flower offload support in cxgb4, from Kumar Sanghvi.

  13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
      Leitner.

  14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.

  15) Add RED qdisc offloadability, and use it in mlxsw driver. From
      Nogah Frankel.

  16) eBPF based device controller for cgroup v2, from Roman Gushchin.

  17) Add some fundamental tracepoints for TCP, from Song Liu.

  18) Remove garbage collection from ipv6 route layer, this is a
      significant accomplishment. From Wei Wang.

  19) Add multicast route offload support to mlxsw, from Yotam Gigi"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
  tcp: highest_sack fix
  geneve: fix fill_info when link down
  bpf: fix lockdep splat
  net: cdc_ncm: GetNtbFormat endian fix
  openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
  netem: remove unnecessary 64 bit modulus
  netem: use 64 bit divide by rate
  tcp: Namespace-ify sysctl_tcp_default_congestion_control
  net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
  ipv6: set all.accept_dad to 0 by default
  uapi: fix linux/tls.h userspace compilation error
  usbnet: ipheth: prevent TX queue timeouts when device not ready
  vhost_net: conditionally enable tx polling
  uapi: fix linux/rxrpc.h userspace compilation errors
  net: stmmac: fix LPI transitioning for dwmac4
  atm: horizon: Fix irq release error
  net-sysfs: trigger netlink notification on ifalias change via sysfs
  openvswitch: Using kfree_rcu() to simplify the code
  openvswitch: Make local function ovs_nsh_key_attr_size() static
  openvswitch: Fix return value check in ovs_meter_cmd_features()
  ...
2017-11-15 11:56:19 -08:00
Linus Torvalds
6aa2f9441f This is the bulk of GPIO changes for the v4.15 kernel cycle:
CORE:
 - Fix the semantics of raw GPIO to actually be raw. No
   inversion semantics as before, but also no open draining,
   and allow the raw operations to affect lines used for
   interrupts as the caller supposedly knows what they are
   doing if they are getting the big hammer.
 
 - Rewrote the __inner_function() notation calls to names that
   make more sense. I just find this kind of code disturbing.
 
 - Drop the .irq_base() field from the gpiochip since now all
   IRQs are mapped dynamically. This is nice.
 
 - Support for .get_multiple() in the core driver API. This
   allows us to read several GPIO lines with a single
   register read. This has high value for some usecases: it
   can be used to create oscilloscopes and signal analyzers
   and other things that rely on reading several lines at
   exactly the same instant. Also a generally nice
   optimization. This uses the new assign_bit() macro from
   the bitops lib that was ACKed by Andrew Morton and
   is implemented for two drivers, one of them being the
   generic MMIO driver so everyone using that will be able
   to benefit from this.
 
 - Do not allow requests of Open Drain and Open Source
   setting of a GPIO line simultaneously. If the hardware
   actually supports enabling both at the same time the
   electrical result would be disastrous.
 
 - A new interrupt chip core helper. This will be helpful
   to deal with "banked" GPIOs, which means GPIO controllers
   with several logical blocks of GPIO inside them. This
   is several gpiochips per device in the device model, in
   contrast to the case when there is a 1-to-1 relationship
   between a device and a gpiochip.
 
 NEW DRIVERS:
 
 - Maxim MAX3191x industrial serializer, a very interesting
   piece of professional I/O hardware.
 
 - Uniphier GPIO driver. This is the GPIO block from the
   recent Socionext (ex Fujitsu and Panasonic) platform.
 
 - Tegra 186 driver. This is based on the new banked GPIO
   infrastructure.
 
 OTHER IMPROVEMENTS:
 
 - Some documentation improvements.
 
 - Wakeup support for the DesignWare DWAPB GPIO controller.
 
 - Reset line support on the DesignWare DWAPB GPIO controller.
 
 - Several non-critical bug fixes and improvements for the
   Broadcom BRCMSTB driver.
 
 - Misc non-critical bug fixes like exotic errorpaths, removal
   of dead code etc.
 
 - Explicit comments on fall-through switch() statements.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJaCvGiAAoJEEEQszewGV1z+oAQAJUpdPH/msdgHDuXSuBcbuFq
 NObQdkRiz1hez4vJOT+kbgES6ay57MArnbmM/xRdy+37lKrmkP+yfZe4UUruQhhW
 f2GVlwBbUp9tIzNliS8IYWO0tj+BTYyg1MQx0C0nE1zMZqVZk44EDa9SO6esRaFJ
 SLc2BpO3oJCQRaObe0+KTHIJV0dK3vQh4QXSzL+cM5u7P67Jq+wv4xdLVVScwbJB
 4jgwVER3Ah0E1jHclIG2PxI1rbYKwlOBumafOTUlq5fmfC3tULVPJEm9FXcdaBLJ
 KAmtxX4yi+SgUccYFsmK+fNNLVQiAjmkhJCl6kxVOrxYqamrG100YST4Iew3sakM
 /iQ3lpup5L6eJ/dndfgE207OqRFhvAzNRxORv1p/wJIRLmV1/QehCX8GYOcDumXY
 MySRcEeUeZPfBHcnjIDRP6y/XOg8zBKso7GL+feRgLZUJZlNQZqokdC95TY9S5nm
 QLK+sU367o41tomyv5TP3y1DDsym6+ZdpuOUh73znxuz2x/x+FfTfwM2J0r8Ussm
 GQTfAojeBI9aSOZ2mvgRI1XxSprXqO3FFFWBwrQ6RS9rBceLF1o2ySKC2gI0FG5d
 6GBkARcN5RyyNtYkH923pyrqz/FZJc6ZkrsUTGmERM5HGuWwczcditqwYRhbHwl8
 pIlmX4y0AYh6FFVoIcQE
 =8Mon
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.15 kernel cycle:

  Core:

   - Fix the semantics of raw GPIO to actually be raw. No inversion
     semantics as before, but also no open draining, and allow the raw
     operations to affect lines used for interrupts as the caller
     supposedly knows what they are doing if they are getting the big
     hammer.

   - Rewrote the __inner_function() notation calls to names that make
     more sense. I just find this kind of code disturbing.

   - Drop the .irq_base() field from the gpiochip since now all IRQs are
     mapped dynamically. This is nice.

   - Support for .get_multiple() in the core driver API. This allows us
     to read several GPIO lines with a single register read. This has
     high value for some usecases: it can be used to create
     oscilloscopes and signal analyzers and other things that rely on
     reading several lines at exactly the same instant. Also a generally
     nice optimization. This uses the new assign_bit() macro from the
     bitops lib that was ACKed by Andrew Morton and is implemented for
     two drivers, one of them being the generic MMIO driver so everyone
     using that will be able to benefit from this.

   - Do not allow requests of Open Drain and Open Source setting of a
     GPIO line simultaneously. If the hardware actually supports
     enabling both at the same time the electrical result would be
     disastrous.

   - A new interrupt chip core helper. This will be helpful to deal with
     "banked" GPIOs, which means GPIO controllers with several logical
     blocks of GPIO inside them. This is several gpiochips per device in
     the device model, in contrast to the case when there is a 1-to-1
     relationship between a device and a gpiochip.

  New drivers:

   - Maxim MAX3191x industrial serializer, a very interesting piece of
     professional I/O hardware.

   - Uniphier GPIO driver. This is the GPIO block from the recent
     Socionext (ex Fujitsu and Panasonic) platform.

   - Tegra 186 driver. This is based on the new banked GPIO
     infrastructure.

  Other improvements:

   - Some documentation improvements.

   - Wakeup support for the DesignWare DWAPB GPIO controller.

   - Reset line support on the DesignWare DWAPB GPIO controller.

   - Several non-critical bug fixes and improvements for the Broadcom
     BRCMSTB driver.

   - Misc non-critical bug fixes like exotic errorpaths, removal of dead
     code etc.

   - Explicit comments on fall-through switch() statements"

* tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (65 commits)
  gpio: tegra186: Remove tegra186_gpio_lock_class
  gpio: rcar: Add r8a77995 (R-Car D3) support
  pinctrl: bcm2835: Fix some merge fallout
  gpio: Fix undefined lock_dep_class
  gpio: Automatically add lockdep keys
  gpio: Introduce struct gpio_irq_chip.first
  gpio: Disambiguate struct gpio_irq_chip.nested
  gpio: Add Tegra186 support
  gpio: Export gpiochip_irq_{map,unmap}()
  gpio: Implement tighter IRQ chip integration
  gpio: Move lock_key into struct gpio_irq_chip
  gpio: Move irq_valid_mask into struct gpio_irq_chip
  gpio: Move irq_nested into struct gpio_irq_chip
  gpio: Move irq_chained_parent to struct gpio_irq_chip
  gpio: Move irq_default_type to struct gpio_irq_chip
  gpio: Move irq_handler to struct gpio_irq_chip
  gpio: Move irqdomain into struct gpio_irq_chip
  gpio: Move irqchip into struct gpio_irq_chip
  gpio: Introduce struct gpio_irq_chip
  pinctrl: armada-37xx: remove unused variable
  ...
2017-11-14 17:23:44 -08:00
Thierry Reding
f0fbe7bce7 gpio: Move irqdomain into struct gpio_irq_chip
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-08 14:06:21 +01:00
David S. Miller
6e300769dc wireless-drivers-next patches for 4.15
Mostly fixes this time, but also few new features.
 
 Major changes:
 
 wil6210
 
 * remove ssid debugfs file
 
 rsi
 
 * add WOWLAN support for suspend, hibernate and shutdown states
 
 ath10k
 
 * add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
   where it's supported (QCA99x0 and QCA4019)
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJZ/HSCAAoJEG4XJFUm622b2sQH+wXgE1swS9xp1AfV3hcVLGoJ
 YjLjR3/BAxsIqkYwhswarTDrD3jsOKrL4ywRk+0BAdR7f2BeOYhQXtZqgjvE8cbu
 WWv5LmSwuKM6tF3ujgjQ6yZvgyDHl2d7lZL59EWG05K/yjJuU8ByoUhLKM5IiqPh
 SWXj3ZtydgGZm2eZTPyan+MFz91jw/X23Jm/AaIAxayf+1J4n1lNpc4rRhUxh/oy
 kGLQ2vsVnegSiHJWTboDFPeRha+daBsbf1MQc0Bh7MzDoWcaqSNX5VgrbaRqp35u
 sb9pmPZS4FzvAdU3bJ9AIPa9ujjblEvDp1JIhrfBUqiuTdvXDZ7XtW8kVsJk1RY=
 =MvWY
 -----END PGP SIGNATURE-----

Merge tag 'wireless-drivers-next-for-davem-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.15

Mostly fixes this time, but also few new features.

Major changes:

wil6210

* remove ssid debugfs file

rsi

* add WOWLAN support for suspend, hibernate and shutdown states

ath10k

* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
  where it's supported (QCA99x0 and QCA4019)
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-04 18:07:50 +09:00
David S. Miller
2a171788ba Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Files removed in 'net-next' had their license header updated
in 'net'.  We take the remove from 'net-next'.

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-04 09:26:51 +09:00
Greg Kroah-Hartman
b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Joe Perches
758f7e0606 bcma: Use bcma_debug and not pr_cont in MIPS driver
Commit 66cc044249 ("bcma: use bcma_debug and pr_cont in MIPS driver")
converted a printk(KERN_DEBUG to bcma_debug.

bcma_debug is guarded by a #define DEBUG via pr_debug.

This means that the bcma_debug will generally not be emitted
but any pr_cont following the bcma_debug will be emitted.

Correct this by removing the uses of pr_cont by using a temporary.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-10-27 11:01:37 +03:00
Rafał Miłecki
66cc044249 bcma: use bcma_debug and pr_cont in MIPS driver
Using bcma_debug gives a device-specific prefix for messages and pr_cont
is a common helper for continuing a line.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-By: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-10-17 17:22:07 +03:00
Randy Dunlap
0f0a0af826 bcma: keep *config menu together
Use "if BCMA"/"endif" around all Kconfig symbols so that they are
kept together in *config menus instead of showing up in unexpected
places. Also remove "depends on BCMA" since this is handled by the
"if BCMA" addition.

Tested with ARCH={x86_64,MIPS} using make {n,menu,g,x}config.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-10-13 12:37:21 +03:00
Vincent Legoll
9ca766b364 bcma: make BCMA a menuconfig to ease disabling it all
No need to get into the submenu to disable all BCMA-related config entries.

Signed-off-by: Vincent Legoll <vincent.legoll@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-08-08 14:44:40 +03:00
Florian Fainelli
459c35148e bcma: gpio: Correct number of GPIOs for BCM53573
Broadcom BCM53573 SoCs actually have 32 GPIOs, and not 16.

Fixes: 3f37ec79dd ("bcma: support BCM53573 series of wireless SoCs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-07-27 13:59:07 +03:00
Rafał Miłecki
f825f6ed20 bcma: fill core OF info independently of bus type
PCI devices can be described in DT as well so we should always execute
relevant code. This will make bcma e.g. set of_node for cores described
in DT.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-03-20 19:12:01 +02:00
Rafał Miłecki
5e48a4cd2e bcma: use helper function to set core dev's parent
A tiny code deduplication thanks to the bcma_bus_get_host_dev.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-03-20 19:12:00 +02:00
Rafał Miłecki
48d1977655 bcma: drop unneeded check for CONFIG_OF_IRQ
We already have the same check in bcma_of_get_irq which really calls
symbols available with CONFIG_OF_IRQ only. It appears this duplicated
check was accidentally added in commit c58d900cc9 ("bcma: fix building
without OF_IRQ"). The rest of code in bcma_of_fill_device should work
fine without CONFIG_OF_IRQ.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-03-20 19:11:11 +02:00