Currently the spi_master is allocated by devm_spi_alloc_master()
and devres core manages the deallocation, but in probe failure
path spi_master_put() is being handled manually which causes
"refcount underflow use-after-free" warning when probe failure happens
after allocating spi_master.
Trimmed backtrace during failure:
refcount_t: underflow; use-after-free.
pc : refcount_warn_saturate+0xf4/0x144
Call trace:
refcount_warn_saturate
kobject_put
put_device
devm_spi_release_controller
devres_release_all
This commit makes relevant changes to remove spi_master_put() from probe
failure path.
Fixes: 606e5d4081 ("spi: cadence-quadspi: Handle spi_unregister_master() in remove()")
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20220601071611.11853-1-vaishnav.a@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enabling the SPI CS35L41 audio codec driver for Steam Deck [1]
revealed a problem with the current AMD SPI controller driver
implementation, consisting of an unrecoverable system hang.
The issue can be prevented if we ensure the max transfer size
and the max message size do not exceed the FIFO buffer size.
According to the implementation of the downstream driver, the
AMD SPI controller is not able to handle more than 70 bytes per
transfer, which corresponds to the size of the FIFO buffer.
Hence, let's fix this by setting the SPI limits mentioned above.
[1] https://lore.kernel.org/r/20220621213819.262537-1-cristian.ciocaltea@collabora.com
Reported-by: Anastasios Vacharakis <vacharakis@o2mail.de>
Fixes: bbb336f39e ("spi: spi-amd: Add AMD SPI controller driver support")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20220706100626.1234731-2-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When using the normal read operation for data transfers, the dummy bus
width is zero. In that case, they are no dummy bytes to transfer and
setting the dummy field in the controller register becomes useless.
Issue was found on a custom "Bifrost" board based on the AST2500 SoC
and using a MX25L51245GMI-08G SPI Flash.
Reported-by: Ian Woloschin <ian.woloschin@akamai.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Tested-by: Ian Woloschin <iwolosch@akamai.com>
Fixes: 9da06d7bde ("spi: aspeed: Add support for direct mapping")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220622161617.3719096-3-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The default value of the control register is set using the direct
mapping information passed to the ->dirmap_create() handler. Dump the
mapping range and the SPI memory operation characteristics to analyze
how the register value has been computed.
spi-aspeed-smc 1e630000.spi: CE0 read dirmap [ 0x00000000 - 0x04000000 ] OP 0x6c mode:1.1.1.4 naddr:0x4 ndummies:0x1
...
spi-aspeed-smc 1e630000.spi: CE0 write dirmap [ 0x00000000 - 0x04000000 ] OP 0x12 mode:1.1.0.1 naddr:0x4 ndummies:0x0
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220622161617.3719096-2-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Avoid pio_write process is preempted, resulting in abnormal state.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Signed-off-by: Jon <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220617124251.5051-1-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In spi_mem_exec_op(), in case cs_gpiod descriptor is set, exec_op()
callback can't be used.
The same must be applied in spi_mem_poll_status(), poll_status()
callback can't be used, we must use the legacy path using
read_poll_timeout().
Tested on STM32mp257c-ev1 specific evaluation board on which a
spi-nand was mounted instead of a spi-nor.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220602091022.358127-1-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The depth of the transmit FIFO for the Cadence SPI controller is currently
hardcoded to 128. But the depth is a synthesis configuration parameter of
the core and can vary between different SoCs.
If the configured FIFO size is less than 128 the driver will busy loop in
the cdns_spi_fill_tx_fifo() function waiting for FIFO space to become
available.
Depending on the length and speed of the transfer it can spin for a
significant amount of time. The cdns_spi_fill_tx_fifo() function is called
from the drivers interrupt handler, so it can leave interrupts disabled for
a prolonged amount of time.
In addition the read FIFO will also overflow and data will be discarded.
To avoid this detect the actual size of the FIFO and use that rather than
the hardcoded value.
To detect the FIFO size the FIFO threshold register is used. The register
is sized so that it can hold FIFO size - 1 as its maximum value. Bits that
are not needed to hold the threshold value will always read 0. By writing
0xffff to the register and then reading back the value in the register we
get the FIFO size.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20220527091143.3780378-1-lars@metafoo.de
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of unprepare_transfer_hardware, SPI controller will be disabled
which will indirectly deassert the CS line. This will create a problem
in some of the devices where message will be transferred with
cs_change flag set(CS should not be deasserted).
As per SPI controller implementation, if SPI controller is disabled then
all output enables are inactive and all pins are set to input mode which
means CS will go to default state high(deassert). This leads to an issue
when core explicitly ask not to deassert the CS (cs_change = 1). This
patch fix the above issue by checking the Slave select status bits from
configuration register before disabling the SPI.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20220606062525.18447-1-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the set of driver core changes for 5.19-rc1.
Note, I'm not really happy with this pull request as-is, see below for
details, but overall this is all good for everything but a small set of
systems, which we have a fix for already.
Lots of tiny driver core changes and cleanups happened this cycle,
but the two major things were:
- firmware_loader reorganization and additions including the
ability to have XZ compressed firmware images and the ability
for userspace to initiate the firmware load when it needs to,
instead of being always initiated by the kernel. FPGA devices
specifically want this ability to have their firmware changed
over the lifetime of the system boot, and this allows them to
work without having to come up with yet-another-custom-uapi
interface for loading firmware for them.
- physical location support added to sysfs so that devices that
know this information, can tell userspace where they are
located in a common way. Some ACPI devices already support
this today, and more bus types should support this in the
future.
Smaller changes included:
- driver_override api cleanups and fixes
- error path cleanups and fixes
- get_abi script fixes
- deferred probe timeout changes.
It's that last change that I'm the most worried about. It has been
reported to cause boot problems for a number of systems, and I have a
tested patch series that resolves this issue. But I didn't get it
merged into my tree before 5.18-final came out, so it has not gotten any
linux-next testing.
I'll send the fixup patches (there are 2) as a follow-on series to this
pull request if you want to take them directly, _OR_ I can just revert
the probe timeout changes and they can wait for the next -rc1 merge
cycle. Given that the fixes are tested, and pretty simple, I'm leaning
toward that choice. Sorry this all came at the end of the merge window,
I should have resolved this all 2 weeks ago, that's my fault as it was
in the middle of some travel for me.
All have been tested in linux-next for weeks, with no reported issues
other than the above-mentioned boot time outs.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnv/A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk/fACgvmenbo5HipqyHnOmTQlT50xQ9EYAn2eTq6ai
GkjLXBGNWOPBa5cU52qf
=yEi/
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core changes for 5.19-rc1.
Lots of tiny driver core changes and cleanups happened this cycle, but
the two major things are:
- firmware_loader reorganization and additions including the ability
to have XZ compressed firmware images and the ability for userspace
to initiate the firmware load when it needs to, instead of being
always initiated by the kernel. FPGA devices specifically want this
ability to have their firmware changed over the lifetime of the
system boot, and this allows them to work without having to come up
with yet-another-custom-uapi interface for loading firmware for
them.
- physical location support added to sysfs so that devices that know
this information, can tell userspace where they are located in a
common way. Some ACPI devices already support this today, and more
bus types should support this in the future.
Smaller changes include:
- driver_override api cleanups and fixes
- error path cleanups and fixes
- get_abi script fixes
- deferred probe timeout changes.
It's that last change that I'm the most worried about. It has been
reported to cause boot problems for a number of systems, and I have a
tested patch series that resolves this issue. But I didn't get it
merged into my tree before 5.18-final came out, so it has not gotten
any linux-next testing.
I'll send the fixup patches (there are 2) as a follow-on series to this
pull request.
All have been tested in linux-next for weeks, with no reported issues
other than the above-mentioned boot time-outs"
* tag 'driver-core-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
driver core: fix deadlock in __device_attach
kernfs: Separate kernfs_pr_cont_buf and rename_lock.
topology: Remove unused cpu_cluster_mask()
driver core: Extend deferred probe timeout on driver registration
MAINTAINERS: add Russ Weight as a firmware loader maintainer
driver: base: fix UAF when driver_attach failed
test_firmware: fix end of loop test in upload_read_show()
driver core: location: Add "back" as a possible output for panel
driver core: location: Free struct acpi_pld_info *pld
driver core: Add "*" wildcard support to driver_async_probe cmdline param
driver core: location: Check for allocations failure
arch_topology: Trace the update thermal pressure
kernfs: Rename kernfs_put_open_node to kernfs_unlink_open_file.
export: fix string handling of namespace in EXPORT_SYMBOL_NS
rpmsg: use local 'dev' variable
rpmsg: Fix calling device_lock() on non-initialized device
firmware_loader: describe 'module' parameter of firmware_upload_register()
firmware_loader: Move definitions from sysfs_upload.h to sysfs.h
firmware_loader: Fix configs for sysfs split
selftests: firmware: Add firmware upload selftests
...
A couple of fixes that came in during the merge window, a driver
fix for spurious timeouts in the fsi driver and an improvement to
make the core display error messages for transfer_one_message()
to help people debug things.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmKXHOwACgkQJNaLcl1U
h9Cxtgf+KCYOZovyBpvHaGuwUrf5fJ3SEbS5BaEhGjyQfTSeSbZuct0+gREJbBu4
AkEOt1/VXWm3EILFbLJV1xsvIj7xhQMwGRhoKEAZ0wjtV/YK2IMC6ISvrDZL2Prr
+A/p5PJu0dHLFlOUfKbkEMa2Ez/Gm/BUR6sfCzswqG6qebRcVF6svctZ/gm+Dqvy
cBvJxqIbSdYwzAqkbrTCZiQgbtJrntagaP4WtpReTMpqrLuXD/VBFK8anzhVsREz
wCTFBi0tSSe6yXOgtGc1Gzvj2wFZ2LRGPvV7nLSfQ2YaruoSM1rwo/xPxtWxsn85
MK8dp1L5d0j7LKzG2q/gPhih0oA1Bg==
=gf5o
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.19-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of fixes that came in during the merge window: a driver fix
for spurious timeouts in the fsi driver and an improvement to make the
core display error messages for transfer_one_message() to help people
debug things"
* tag 'spi-fix-v5.19-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: core: Display return code when failing to transfer message
spi: fsi: Fix spurious timeout
This series has been 12 years in the making, it mostly finishes the
work that was started with the founding of Linaro to clean up platform
support in the kernel.
The largest change here is a cleanup of the omap1 platform, which
is the final ARM machine type to get converted to the common-clk
subsystem. All the omap1 specific drivers are now made independent of the
mach/*.h headers to allow the platform to be part of a generic ARMv4/v5
multiplatform kernel. The last bit that enables this support is still
missing here while we wait for some last dependencies to make it into
the mainline kernel through other subsystems.
The s3c24xx, ixp4xx, iop32x, ep93xx and dove platforms were all almost
at the point of allowing multiplatform kernels, this work gets completed
here along with a few additional cleanup. At the same time, the s3c24xx
and s3c64xx are now deprecated and expected to get removed in the future.
The PXA and OMAP1 bits are in a separate branch because of dependencies.
Once both branches are merged, only the three Intel StrongARM platforms
(RiscPC, Footbridge/NetWinder and StrongARM1100) need separate kernels,
and there are no plans to include these.
-----BEGIN PGP SIGNATURE-----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=CTtN
-----END PGP SIGNATURE-----
Merge tag 'arm-multiplatform-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARMv4T/v5 multiplatform support from Arnd Bergmann:
"This series has been 12 years in the making, it mostly finishes the
work that was started with the founding of Linaro to clean up platform
support in the kernel.
The largest change here is a cleanup of the omap1 platform, which is
the final ARM machine type to get converted to the common-clk
subsystem. All the omap1 specific drivers are now made independent of
the mach/*.h headers to allow the platform to be part of a generic
ARMv4/v5 multiplatform kernel.
The last bit that enables this support is still missing here while we
wait for some last dependencies to make it into the mainline kernel
through other subsystems.
The s3c24xx, ixp4xx, iop32x, ep93xx and dove platforms were all almost
at the point of allowing multiplatform kernels, this work gets
completed here along with a few additional cleanup. At the same time,
the s3c24xx and s3c64xx are now deprecated and expected to get removed
in the future.
The PXA and OMAP1 bits are in a separate branch because of
dependencies. Once both branches are merged, only the three Intel
StrongARM platforms (RiscPC, Footbridge/NetWinder and StrongARM1100)
need separate kernels, and there are no plans to include these"
* tag 'arm-multiplatform-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: ixp4xx: Consolidate Kconfig fixing issue
ARM: versatile: Add missing of_node_put in dcscb_init
ARM: config: Refresh IXP4xx config after multiplatform
ARM: omap1: add back omap_set_dma_priority() stub
ARM: omap: fix missing declaration warnings
ARM: omap: fix address space warnings from sparse
ARM: spear: remove include/mach/ subdirectory
ARM: davinci: remove include/mach/ subdirectory
ARM: omap2: remove include/mach/ subdirectory
integrator: remove empty ap_init_early()
ARM: s3c: fix include path
MAINTAINERS: omap1: Add Janusz as an additional maintainer
ARM: omap1: htc_herald: fix typos in comments
ARM: OMAP1: fix typos in comments
ARM: OMAP1: clock: Remove noop code
ARM: OMAP1: clock: Remove unused code
ARM: OMAP1: clock: Fix UART rate reporting algorithm
ARM: OMAP1: clock: Fix early UART rate issues
ARM: OMAP1: Prepare for conversion of OMAP1 clocks to CCF
ARM: omap1: fix build with no SoC selected
...
All the other calls to the controller driver display the error
return code. The return code is helpful to understand what went
wrong, so include it when failing to transfer one message.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220525165852.33167-3-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver may return a timeout error even if the status register
indicates that the transfer may proceed. Fix this by restructuring
the polling loop.
Fixes: 89b35e3f28 ("spi: fsi: Implement a timeout for polling status")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220525165852.33167-2-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Not much dramatic changes at this time, but we've received quite
a lot of changes for ASoC, while there are still a few fixes and
quirks for usual HD- and USB-auido. Here are some highlights.
* ASoC:
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs
- Initial stages of Intel AVS driver merge
- Introduction of v4 IPC mechanism for SOF
- TDM mode support for AK4613
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
* Others
- A few regression fixes after the USB-audio endpoint management
refactoring
- More enhancements for Cirrus HD-audio codec support (still ongoing)
- Addition of generic serial MIDI driver
-----BEGIN PGP SIGNATURE-----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=5qBk
-----END PGP SIGNATURE-----
Merge tag 'sound-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Not much dramatic changes at this time, but we've received quite a lot
of changes for ASoC, while there are still a few fixes and quirks for
usual HD- and USB-auido. Here are some highlights.
ASoC:
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs
- Initial stages of Intel AVS driver merge
- Introduction of v4 IPC mechanism for SOF
- TDM mode support for AK4613
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
Others:
- A few regression fixes after the USB-audio endpoint management
refactoring
- More enhancements for Cirrus HD-audio codec support (still ongoing)
- Addition of generic serial MIDI driver"
* tag 'sound-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (504 commits)
ALSA: hda/realtek - Add new type for ALC245
ALSA: usb-audio: Configure sync endpoints before data
ALSA: ctxfi: fix typo in comment
ALSA: cs5535audio: fix typo in comment
ALSA: ctxfi: Add SB046x PCI ID
ALSA: usb-audio: Add missing ep_idx in fixed EP quirks
ALSA: usb-audio: Workaround for clock setup on TEAC devices
ALSA: lola: Bounds check loop iterator against streams array size
ASoC: max98090: Move check for invalid values before casting in max98090_put_enab_tlv()
ASoC: rt1308-sdw: add the default value of register 0xc320
ASoC: rt9120: Use pm_runtime and regcache to optimize 'pwdnn' logic
ASoC: rt9120: Fix 3byte read, valule offset typo
ASoC: amd: acp: Set Speaker enable/disable pin through rt1019 codec driver.
ASoC: amd: acp: Set Speaker enable/disable pin through rt1019 codec driver
ASoC: wm2000: fix missing clk_disable_unprepare() on error in wm2000_anc_transition()
ASoC: codecs: lpass: Fix passing zero to 'PTR_ERR'
ASoC: SOF: sof-client-ipc-flood-test: use pm_runtime_resume_and_get()
ASoC: SOF: mediatek: remove duplicate include in mt8195.c
ASoC: SOF: mediatek: Add mt8195 debug dump
ASoC: SOF: mediatek: Add mediatek common debug dump
...
This is quite a quiet release but some new drivers mean that the
diffstat is fairly large, the new drivers include the aspeed driver
which is migrated from MTD as part of the ongoing move of controllers
with specialised support for SPI flashes into the SPI subsystem.
- Support for devices which flip CPHA during recieve only transfers
(eg, if MOSI and MISO have inverted polarity).
- Overhaul of the i.MX driver, including the addition of PIO support
for better performance on small transfers.
- Migration of the Aspeed driver from MTD.
- Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
IPM and SFI.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmKLh9wACgkQJNaLcl1U
h9ApgAf/SvcHRyM06hw+00D2PAco7mxSiAs7rebxj4f0zPRNvUrYbUDWjakeKjoB
ocmpY6AW/vRBUM9xZsiQiLp/9NPltnVghZIBgp5gcS8zaXdxiZjZ68Z+uYp9SP9v
zj8F6bBQzk3lvuY+Cr1f68iXICA62Aa1yX28UFVLZkV0d+0AazpECZkb3hjOiL6P
0qSV6IfoFlJXYsyvAS4/MqYrHklSCD/0Ek09V9jPpZJPHn1ldbFs5zkstfs0PMc/
YeDlpStkjJE4OQ6+z6Ou/wGbcw11nWvKCSqF4bGRXLrgR/uIjOKomwOzaBUf/A6Q
AxQcKMtsBTx0VzYmwJwopj0qDvOq/A==
=6yj3
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This is quite a quiet release but some new drivers mean that the
diffstat is fairly large. The new drivers include the aspeed driver
which is migrated from MTD as part of the ongoing move of controllers
with specialised support for SPI flashes into the SPI subsystem.
- Support for devices which flip CPHA during recieve only transfers
(eg, if MOSI and MISO have inverted polarity).
- Overhaul of the i.MX driver, including the addition of PIO support
for better performance on small transfers.
- Migration of the Aspeed driver from MTD.
- Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
IPM and SFI"
* tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (84 commits)
spi: spi-au1550: replace ternary operator with min()
mtd: spi-nor: aspeed: set the decoding size to at least 2MB for AST2600
spi: aspeed: Calibrate read timings
spi: aspeed: Add support for the AST2400 SPI controller
spi: aspeed: Workaround AST2500 limitations
spi: aspeed: Adjust direct mapping to device size
spi: aspeed: Add support for direct mapping
spi: spi-mem: Convert Aspeed SMC driver to spi-mem
spi: Convert the Aspeed SMC controllers device tree binding
spi: spi-cadence: Update ISR status variable type to irqreturn_t
spi: Doc fix - Describe add_lock and dma_map_dev in spi_controller
spi: cadence-quadspi: Handle spi_unregister_master() in remove()
spi: stm32-qspi: Remove SR_BUSY bit check before sending command
spi: stm32-qspi: Always check SR_TCF flags in stm32_qspi_wait_cmd()
spi: stm32-qspi: Fix wait_cmd timeout in APM mode
spi: cadence-quadspi: remove unnecessary (void *) casts
spi: cadence-quadspi: Add missing blank line in cqspi_request_mmap_dma()
spi: spi-imx: mx51_ecspi_prepare_message(): skip writing MX51_ECSPI_CONFIG register if unchanged
spi: spi-imx: add PIO polling support
spi: spi-imx: replace struct spi_imx_data::bitbang by pointer to struct spi_controller
...
This is quite a big update, partly due to the addition of some larger
drivers (more of which is to follow since at least the AVS driver is
still a work in progress) and partly due to Charles' work sorting out
our handling of endianness. As has been the case recently it's much
more about drivers than the core.
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs.
- Initial stages of Intel AVS driver merge.
- Introduction of v4 IPC mechanism for SOF.
- TDM mode support for AK4613.
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmKLf5EACgkQJNaLcl1U
h9ASqAf/YnwbFP919ree/DEKUDCNc4klUH5M4JOexXbZlZDqxKYRGZjoLuiwX/PQ
Au/xOjGEvm3Yg5/g5c8YFVNcIkv1O8VclRkV59oIxlBwKmQeTKvq+lOmlel2l1wZ
XOmvHjE46wxH1N1cLwL6KkX0YDn59orSZGYZRpfLjL61y6LQWsLNU0tY6AWCRATB
Llnrbu+DYgCsYNTEOOOY5s4V+4LkQm8TLdft91Va7mBdkPPRFoXRO0HGcVBqbkoN
7pf2mrjrLAWL9yuA8FlrgJbHq58DF9WGe5uEU7qlVL1zw46ClgIM0ABxPOdNdjV2
Wzb1jI7GmztgQNxlR9BcJB0kxAj9vA==
=oD5l
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.19' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.19
This is quite a big update, partly due to the addition of some larger
drivers (more of which is to follow since at least the AVS driver is
still a work in progress) and partly due to Charles' work sorting out
our handling of endianness. As has been the case recently it's much
more about drivers than the core.
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs.
- Initial stages of Intel AVS driver merge.
- Introduction of v4 IPC mechanism for SOF.
- TDM mode support for AK4613.
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
Merge series from Cédric Le Goater <clg@kaod.org>:
This series adds a new SPI driver using the spi-mem interface for the
Aspeed static memory controllers of the AST2600, AST2500 and AST2400
SoCs.
* AST2600 Firmware SPI Memory Controller (FMC)
* AST2600 SPI Flash Controller (SPI1 and SPI2)
* AST2500 Firmware SPI Memory Controller (FMC)
* AST2500 SPI Flash Controller (SPI1 and SPI2)
* AST2400 New Static Memory Controller (also referred as FMC)
* AST2400 SPI Flash Controller (SPI)
It is based on the current OpenBMC kernel driver [1], using directly
the MTD SPI-NOR interface and on a patchset [2] previously proposed
adding support for the AST2600 only. This driver takes a slightly
different approach to cover all 6 controllers.
It does not make use of the controller register disabling Address and
Data byte lanes because is not available on the AST2400 SoC. We could
introduce a specific handler for new features available on recent SoCs
if needed. As there is not much difference on performance, the driver
chooses the common denominator: "User mode" which has been heavily
tested in [1]. "User mode" is also used as a fall back method when
flash device mapping window is too small.
Problems to address with spi-mem were the configuration of the mapping
windows and the calibration of the read timings. The driver handles
them in the direct mapping handler when some knowledge on the size of
the flash device is know. It is not perfect but not incorrect either.
The algorithm is one from [1] because it doesn't require the DMA
registers which are not available on all controllers.
Direct mapping for writes is not supported (yet). I have seen some
corruption with writes and I preferred to use the safer and proven
method of the initial driver [1]. We can improve that later.
The driver supports Quad SPI RX transfers on the AST2600 SoC but it
didn't have the expected results. Therefore it is not activated yet.
There are some issues on the pinctrl to investigate first.
Tested on:
* OpenPOWER Palmetto (AST2400)
* Facebook Wedge 100 BMC (AST2400) by Tao Ren <rentao.bupt@gmail.com>
* Evaluation board (AST2500)
* Inspur FP5280G2 BMC (AST2500) by John Wang <wangzq.jn@gmail.com>
* Facebook Backpack CMM BMC (AST2500) by Tao Ren <rentao.bupt@gmail.com>
* OpenPOWER Witherspoon (AST2500)
* Evaluation board (AST2600 A0 and A3)
* Rainier board (AST2600)
[1] https://github.com/openbmc/linux/blob/dev-5.15/drivers/mtd/spi-nor/controllers/aspeed-smc.c
[2] https://patchwork.ozlabs.org/project/linux-aspeed/list/?series=212394
Fix the following coccicheck warnings:
drivers/spi/spi-au1550.c:408:21-22: WARNING opportunity for min()
drivers/spi/spi-au1550.c:542:21-22: WARNING opportunity for min()
min() macro is defined in include/linux/minmax.h. It avoids multiple
evaluations of the arguments when non-constant and performs strict
type-checking.
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Link: https://lore.kernel.org/r/20220513130333.58379-1-guozhengkui@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In AST2600, the unit of SPI CEx decoding range register is 1MB, and end
address offset is set to the acctual offset - 1MB. If the flash only has
1MB, the end address will has same value as start address, which will
causing unexpected errors.
This patch set the decoding size to at least 2MB to avoid decoding errors.
Tested:
root@bletchley:~# dmesg | grep "aspeed-smc 1e631000.spi: CE0 window"
[ 59.328134] aspeed-smc 1e631000.spi: CE0 window resized to 2MB (AST2600 Decoding)
[ 59.343001] aspeed-smc 1e631000.spi: CE0 window [ 0x50000000 - 0x50200000 ] 2MB
root@bletchley:~# devmem 0x1e631030
0x00100000
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
[ clg : Ported on new spi-mem driver ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-12-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
To accommodate the different response time of SPI transfers on different
boards and different SPI NOR devices, the Aspeed controllers provide a
set of Read Timing Compensation registers to tune the timing delays
depending on the frequency being used. The AST2600 SoC has one of these
registers per device. On the AST2500 and AST2400 SoCs, the timing
register is shared by all devices which is problematic to get good
results other than for one device.
The algorithm first reads a golden buffer at low speed and then performs
reads with different clocks and delay cycle settings to find a breaking
point. This selects a default good frequency for the CEx control register.
The current settings are a bit optimistic as we pick the first delay giving
good results. A safer approach would be to determine an interval and
choose the middle value.
Calibration is performed when the direct mapping for reads is created.
Since the underlying spi-nor object needs to be initialized to create
the spi_mem operation for direct mapping, we should be fine. Having a
specific API would clarify the requirements though.
Cc: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-9-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the driver for the AST2400 SPI Flash Controller (SPI). This
controller has a slightly different interface which requires
adaptation of the 4B handling. Summary of features :
. host Firmware
. 1 chip select pin (CE0)
. slightly different register set, between AST2500 and the legacy
controller
. no segment registers
. single, dual mode.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-8-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not possible to configure a full 128MB window for a chip of the
same size on the AST2500 SPI controller. For this case, the maximum
window size is restricted to 120MB for CE0.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-7-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The segment registers of the FMC/SPI controllers provide a way to
configure the mapping window of the flash device contents on the AHB
bus. Adjust this window to the size of the spi-mem mapping.
Things get more complex with multiple devices. The driver needs to
also adjust the window of the next device to make sure that there is
no overlap, even if there is no available device. The proposal below
is not perfect but it is covering all the cases we have seen on
different boards with one and two devices on the same bus.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-6-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use direct mapping to read the flash device contents. This operation
mode is called "Command mode" on Aspeed SoC SMC controllers. It uses a
Control Register for the settings to apply when a memory operation is
performed on the flash device mapping window.
If the window is not big enough, fall back to the "User mode" to
perform the read.
Direct mapping for writes will come later when validated.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-5-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This SPI driver adds support for the Aspeed static memory controllers
of the AST2600, AST2500 and AST2400 SoCs using the spi-mem interface.
* AST2600 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. Only supports SPI type flash memory
. different segment register interface
. single, dual and quad mode.
* AST2600 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. different segment register interface
. single, dual and quad mode.
* AST2500 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. supports SPI type flash memory (CE0-CE1)
. CE2 can be of NOR type flash but this is not supported by the driver
. single, dual mode.
* AST2500 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. single, dual mode.
* AST2400 New Static Memory Controller (also referred as FMC)
. BMC firmware
. New register set
. 5 chip select pins (CE0 ∼ CE4)
. supports NOR flash, NAND flash and SPI flash memory.
. single, dual and quad mode.
Each controller has a memory range on which flash devices contents are
mapped. Each device is assigned a window that can be changed at bootime
with the Segment Address Registers.
Each SPI flash device can then be accessed in two modes: Command and
User. When in User mode, SPI transfers are initiated with accesses to
the memory segment of a device. When in Command mode, memory
operations on the memory segment of a device generate SPI commands
automatically using a Control Register for the settings.
This initial patch adds support for User mode. Command mode needs a little
more work to check that the memory window on the AHB bus fits the device
size. It will come later when support for direct mapping is added.
Single and dual mode RX transfers are supported. Other types than SPI
are not supported.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-4-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Data type of status variable, that hold the return value of the ISR,
should be irqreturn_t & not u32. This patch updates status variable type
to irqreturn_t.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20220512145025.20205-1-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently devres managed removal of the spi_controller happens after
removing the power domain of the host platform_device.While this
does not affect the clean removal of the controller, but affects
graceful removal of the child devices if the child device removal
requires issuing commands over SPI.
Eg. flash device being soft reset to 1S-1S-1S mode before removal
so that on next probe operations in 1S-1S-1S mode is successful.
Failure is seen when `rmmod spi-cadence-quadspi` is performed:
root@j7-evm:~# rmmod spi_cadence_quadspi
[ 49.230996] cadence-qspi 47050000.spi: QSPI is still busy after 500ms timeout.
[ 49.238209] spi-nor spi1.0: operation failed with -110
[ 49.244457] spi-nor spi1.0: Software reset failed: -110
and on subsequent modprobe the OSPI flash probe fails as it
is in 8D-8D-8D mode since the previous soft reset did not happen.
root@j7-evm:~# modprobe spi_cadence_quadspi
[ 73.253536] spi-nor spi0.0: unrecognized JEDEC id bytes: ff ff ff ff ff ff
[ 73.260476] spi-nor: probe of spi0.0 failed with error -2
This commit adds necessary changes to perform spi_unregister_master()
in the host device remove() so that the child devices are gracefully
removed before the power domain is removed.
changes tested on J721E with mt35xu512aba flash.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20220511115516.14894-1-vaishnav.a@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from patrice.chotard@foss.st.com <patrice.chotard@foss.st.com>
Patrice Chotard <patrice.chotard@foss.st.com>:
From: Patrice Chotard <patrice.chotard@foss.st.com>
This series update flags management in the following cases:
- In APM mode, don't take care of TCF and TEF flags
- Always check TCF flag in stm32_qspi_wait_cmd()
- Don't check BUSY flag when sending new command
Waiting for SR_BUSY bit when receiving a new command is not needed.
SR_BUSY bit is already managed in the previous command treatment.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220511074644.558874-4-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, SR_TCF flag is checked in case there is data, this criteria
is not correct.
SR_TCF flags is set when programmed number of bytes has been transferred
to the memory device ("bytes" comprised command and data send to the
SPI device).
So even if there is no data, we must check SR_TCF flag.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220511074644.558874-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove a couple of unnecessary casts to `(void *)` when initializing the
`.data` members in the device ID table.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20220510115141.212779-3-abbotti@mev.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
In mx51_ecspi_prepare_message() the MX51_ECSPI_CONFIG register is
setup for the current spi_message. After writing the register, there
is a delay to ensure that the changes hit the hardware.
This patch checks if the register MX51_ECSPI_CONFIG actually needs to
be changed. If the register content is unchanged the function is left
early, skipping the write to the hardware and the delay. This leads to
a small, but measurable performance increase. For a given workload
with small transfers on an imx6 single core the CPU load decreases
from 30% to ~27%.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-10-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver supports several modes, one of them is PIO/IRQ
"spi_imx_pio_transfer()". The data is exchanged with the IP core using
PIO, an IRQ is setup to signal empty/full FIFOs and the end of the
transfer. The IRQ and scheduling overhead for short transfers is
significant. Using polling instead of IRQs can be beneficial to reduce
the overall CPU load, especially on small transfer workloads.
On an imx6 single core, a given RX workload of the mcp251xfd driver
results in 40% CPU load. Using polling mode reduces the CPU load to
30%.
This patch adds PIO polling support to the driver. For transfers with
a duration of less than 30 µs the polling mode instead of IRQ based
PIO mode is used. 30 µs seems to be a good compromise, which is used
the by the SPI drivers for the raspberry Pi (spi-bcm2835,
spi-bcm2835), too.
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-9-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no need to embed the struct spi_bitbang into our private
data (struct spi_imx_data), the spi core is flexible enough, so that
we only need a pointer to the allocated struct spi_controller.
This is also a preparation patch to add PIO based polling support to
the driver.
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-8-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
With patch:
| 8caab75fd2 ("spi: Generalize SPI "master" to "controller"")
the SPI "master" was generalized to "controller". This patch completed
the conversion of the spi-imx driver by replacing the remaining
occurrences of master to controller.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-7-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the following sparse warning by using a swab32s()
instead of a cpu_to_be32(). The driver is used on little endian
systems only and we really want to swap the bytes.
| drivers/spi/spi-imx.c:305:29: warning: incorrect type in assignment (different base types)
| drivers/spi/spi-imx.c:305:29: expected unsigned int val
| drivers/spi/spi-imx.c:305:29: got restricted __be32 [usertype]
| drivers/spi/spi-imx.c:361:21: warning: incorrect type in assignment (different base types)
| drivers/spi/spi-imx.c:361:21: expected unsigned int [assigned] [usertype] val
| drivers/spi/spi-imx.c:361:21: got restricted __be32 [usertype]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-5-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the following checkpatch warning, by making val an
"unsigned int".
| WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
| + unsigned val = 0;
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-4-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the following checkpatch warning by removing the
trailing backslash:
| WARNING: Avoid unnecessary line continuations
| + spi_imx->bitbang.master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH \
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-3-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the following and similar sparse warnings by adding
the missing identifier names to the function definitions:
| WARNING: function definition argument 'struct spi_imx_data *' should also have an identifier name
| #68: FILE: drivers/spi/spi-imx.c:68:
| + int (*prepare_message)(struct spi_imx_data *, struct spi_message *);
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-2-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
It will cause null-ptr-deref if platform_get_resource_byname() returns NULL,
we need check the return value.
Fixes: 858e26a515 ("spi: spi-fsl-qspi: Reduce devm_ioremap size to 4 times AHB buffer size")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220505093954.1285615-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The module omap2-mcspi does not support the interword delay
parameter present in the spi transfer. On one side, if the module
is instructed to use the dma, this parameter is correctly ignored.
However, without the usage of the dma, that parameter should be
used.
The patch introduce the handling of such delay in the omap2-mcspi
module, using standard spi_delay struct. The patch has been tested
using as benchmark a DM3730.
The delay function used (spi_delay_exec) is already present in the
kernel and it checks on its own the validity of the input, as such,
no additional checks are present.
The range of usage of the udelay function is incremented to 200 us,
as the change from udelay to usleep_range introduces not
neglectible delays.
Signed-off-by: Andrea Zanotti <andreazanottifo@gmail.com>
Link: https://lore.kernel.org/r/20220502111300.24754-1-andreazanottifo@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Return -ENOMEM of there is a dma mapping error. Do not return success.
Fixes: 764f1b7481 ("spi: add driver for MTK SPI NAND Flash Interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/YmwjUcTKyQNrrn2g@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
The Cadence QSPI compatible string required for the SoCFPGA platform
changed from the default "cdns,qspi-nor" to "intel,socfpga-qspi" with
the introduction of an additional quirk in
commit 98d948eb83 ("spi: cadence-quadspi: fix write completion support").
However, that change did not preserve the previously used
quirk for this platform. Reinstate the `CQSPI_DISABLE_DAC_MODE` quirk
for the SoCFPGA platform.
Fixes: 98d948eb83 ("spi: cadence-quadspi: fix write completion support")
Cc: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20220427153446.10113-1-abbotti@mev.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver implements support for the SPI-NAND mode of MTK NAND Flash
Interface as a SPI-MEM controller with pipelined ECC capability.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20220424032527.673605-3-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>:
1.Add support for using GPIOs as chip select lines on Ingenic SoCs.
2.Add support for probing the spi-ingenic driver on the JZ4775 SoC,
the X1000 SoC, and the X2000 SoC.
3.Modify annotation texts to be more in line with the current state.
