Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ionic device has on-board memory (CMB) that can be used
for descriptors as a way to speed descriptor access for faster
packet processing. It is rumored to improve latency and/or
packets-per-second for some profiles of small packet traffic,
although your mileage may vary.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor Code cleanup details.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have the pointer already, don't need to go through the
lif struct for it.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In one version of the HW there is a remote possibility that it
will miss the doorbell ring. This adds a bit of protection to
be sure we don't stall a queue from a missed doorbell.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Allen Hubbe <allen.hubbe@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure the q+cq alloc for NotifyQ is clearly documented
and don't bother with unnecessary local variables.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clear the interrupt credits before enabling the queue rather
than after to be sure that the enabled queue starts at 0 and
that we don't wipe away possible credits after enabling the
queue.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Neel Patel <neel.patel@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver name is available in device_driver::name. Right now,
drivers still have to report this piece of information themselves in
their devlink_ops::info_get callback function.
In order to factorize code, make devlink_nl_info_fill() add the driver
name attribute.
Now that the core sets the driver name attribute, drivers are not
supposed to call devlink_info_driver_name_put() anymore. Remove
devlink_info_driver_name_put() and clean-up all the drivers using this
function in their callback.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Tested-by: Ido Schimmel <idosch@nvidia.com> # mlxsw
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A problem about ionic create debugfs failed is triggered with the
following log given:
[ 415.799514] debugfs: Directory 'ionic' with parent '/' already present!
The reason is that ionic_init_module() returns ionic_bus_register_driver()
directly without checking its return value, if ionic_bus_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of ionic can never be created later.
ionic_init_module()
ionic_debugfs_create() # create debugfs directory
ionic_bus_register_driver()
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when ionic_bus_register_driver() returns error.
Fixes: fbfb803153 ("ionic: Add hardware init and device commands")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20221113092929.19161-1-yuancan@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Benefit from the previously implemented tracking of netdev events in
devlink code and instead of calling devlink_port_type_eth_set() and
devlink_port_type_clear() to set devlink port type and link to related
netdev, use SET_NETDEV_DEVLINK_PORT() macro to assign devlink_port
pointer to netdevice which is about to be registered.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same pre-work code is used before each call to
ionic_rx_fill(), so bring it in and make it a part of
the routine.
Signed-off-by: Neel Patel <neel@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support stateless offloads for GRE, VXLAN, GENEVE, IPXIP4
and IPXIP6 when the FW supports them.
Signed-off-by: Neel Patel <neel@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A new ionic dev_cmd is added to the interface in ionic_if.h,
with a new capabilities field in the ionic device identity to
signal its availability in the FW. The identity level code is
incremented to '2' to show support for this new capabilities
bitfield.
If the driver has indicated with the new identity level that
it has the VF_CTRL command, newer FW will wait for the start
command before starting the VFs after a FW update or crash
recovery.
This patch updates the driver to make use of the new VF start
control in fw_up path to be sure that the PF has set the user
attributes on the VF before the FW allows the VFs to restart.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Report the current FW values for the VF attributes, but don't
save the FW values locally, only save the vf attributes that
are given to us from the user. This allows us to replay user
data, and doesn't end up confusing things like "who set the
mac address".
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VF attributes that the user has set into the FW through
the PF can be lost over a FW crash recovery. Much like we
already replay the PF mac/vlan filters, we now add a replay
in the recovery path to be sure the FW has the up-to-date
VF configurations.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It's possible that the driver will dereference a qcq that doesn't exist
when calling ionic_reconfigure_queues(), which causes a page fault BUG.
If a reduction in the number of queues is followed by a different
reconfig such as changing the ring size, the driver can hit a NULL
pointer when trying to clean up non-existent queues.
Fix this by checking to make sure both the qcqs array and qcq entry
exists bofore trying to use and free the entry.
Fixes: 101b40a017 ("ionic: change queue count with no reset")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20221017233123.15869-1-snelson@pensando.io
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure that devlink port is registered first and register netdev
after. Unregister netdev before devlnk port unregister.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Assign a random mac address to the VF interface station
address if it boots with a zero mac address in order to match
similar behavior seen in other VF drivers. Handle the errors
where the older firmware does not allow the VF to set its own
station address.
Newer firmware will allow the VF to set the station mac address
if it hasn't already been set administratively through the PF.
Setting it will also be allowed if the VF has trust.
Fixes: fbb39807e9 ("ionic: support sr-iov operations")
Signed-off-by: R Mohamed Shah <mohamed@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In looping on FW update tests we occasionally see the
FW_ACTIVATE_STATUS command fail while it is in its EAGAIN loop
waiting for the FW activate step to finsh inside the FW. The
firmware is complaining that the done bit is set when a new
dev_cmd is going to be processed.
Doing a clean on the cmd registers and doorbell before exiting
the wait-for-done and cleaning the done bit before the sleep
prevents this from occurring.
Fixes: fbfb803153 ("ionic: Add hardware init and device commands")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a case found in heavy testing where a link flap happens just
before a firmware Recovery event and the driver gets stuck in the
BROKEN state. This comes from the driver getting interrupted by a FW
generation change when coming back up from the link flap, and the call
to ionic_start_queues() in ionic_link_status_check() fails. This can be
addressed by having the fw_up code clear the BROKEN bit if seen, rather
than waiting for a user to manually force the interface down and then
back up.
Fixes: 9e8eaf8427 ("ionic: stop watchdog when in broken state")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The prototype of input features of ionic_set_nic_features() is
netdev_features_t, but the vlan_flags is using the private
definition of ionic drivers. It should use the variable
ctx.cmd.lif_setattr.features, rather than features to check
the vlan flags. So fixes it.
Fixes: beead698b1 ("ionic: Add the basic NDO callbacks for netdev support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most drivers use "skb_transport_offset(skb) + tcp_hdrlen(skb)"
to compute headers length for a TCP packet, but others
use more convoluted (but equivalent) ways.
Add skb_tcp_all_headers() and skb_inner_tcp_all_headers()
helpers to harmonize this a bit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we don't try to transition the fw_status_ready
while we're still in the FW_STOPPING state, else we can
get stuck in limbo waiting on a transition that already
happened.
While we're here we can remove a superfluous check on
the lif pointer.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ever-vigilant Linux kernel test robot reminded us that
we need to use the correct include files to be sure that
all the build variations will work correctly. Adding the
vmalloc.h include takes care of declaring our use of vzalloc()
and vfree().
drivers/net/ethernet/pensando/ionic/ionic_lif.c:396:17: error: implicit
declaration of function 'vfree'; did you mean 'kvfree'?
drivers/net/ethernet/pensando/ionic/ionic_lif.c:531:21: warning:
assignment to 'struct ionic_desc_info *' from 'int' makes pointer from
integer without a cast
Fixes: 116dce0ff0 ("ionic: Use vzalloc for large per-queue related buffers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20220223015731.22025-1-snelson@pensando.io
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix up some checkpatch complaints that have crept in:
doubled words words, mispellled words, doubled lines.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace strlcpy with strscpy to clean up a checkpatch complaint.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use vzalloc for per-queue info structs that don't need any
DMA mapping to help relieve memory pressure found when used
in our limited SOC environment.
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In some graceful updates that get initially triggered by the
RESET event, especially with older firmware, the fw_generation
bits don't change but the fw_status is seen to go to 0 then back
to 1. However, the driver didn't perform the restart, remained
waiting for fw_generation to change, and got left in limbo.
This is because the clearing of idev->fw_status_ready to 0
didn't happen correctly as it was buried in the transition
trigger: since the transition down was triggered not here
but in the RESET event handler, the clear to 0 didn't happen,
so the transition back to 1 wasn't detected.
Fix this particular case by bringing the setting of
idev->fw_status_ready back out to where it was before.
Fixes: 398d1e37f9 ("ionic: add FW_STOPPING state")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This (ab)use of a data buffer made some static code checkers
rather itchy, so we replace the a generic data buffer with
the union in the struct ionic_vf_setattr_cmd.
Fixes: fbb39807e9 ("ionic: support sr-iov operations")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can be premature in detecting stalled firmware
when the heartbeat is not updated because the firmware can
occasionally take a long time (more than 2 seconds) to service
a request, and doesn't update the heartbeat during that time.
The firmware heartbeat is not necessarily a steady 1 second
periodic beat, but better described as something that should
progress at least once in every DECVMD_TIMEOUT period.
The single-threaded design in the FW means that if a devcmd
or adminq request launches a large internal job, it is stuck
waiting for that job to finish before it can get back to
updating the heartbeat. Since all requests are "guaranteed"
to finish within the DEVCMD_TIMEOUT period, the driver needs
to less aggressive in checking the heartbeat progress.
We change our current 2 second window to something bigger than
DEVCMD_TIMEOUT which should take care of most of the issue.
We stop checking for the heartbeat while waiting for a request,
as long as we're still watching for the FW status. Lastly,
we make sure our FW status is up to date before running a
devcmd request.
Once we do this, we need to not check the heartbeat on DEV
commands because it may be stalled while we're on the fw_down
path. Instead, we can rely on the is_fw_running check.
Fixes: b2b9a8d7ed ("ionic: avoid races in ionic_heartbeat_check")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dbid_inuse bitmap is not useful in this driver so remove it.
Fixes: 6461b446f2 ("ionic: Add interrupts and doorbells")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver is going through reset, it will eventually call
ionic_lif_init(), which does a lot of re-initialization. One
of the re-initialization steps is to setup the adminq and
enable napi for it. If something breaks after this point
we can end up with a kernel NULL pointer dereference through
ionic_adminq_napi.
Fix this by making sure to call napi_disable() in the cleanup
path of ionic_lif_init(). This forces any pending napi contexts
to finish and prevents them from being recalled before deleting
the napi context.
Fixes: 77ceb68e29 ("ionic: Add notifyq support")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Buffer DMA mapping happens in ionic_tx_map_skb() and this function is
called from ionic_tx() and ionic_tx_tso(). If ionic_tx_map_skb()
succeeds, but a failure is encountered later in ionic_tx() or
ionic_tx_tso() we aren't unmapping the buffers. This can be fixed in
ionic_tx() by changing functions it calls to return void because they
always return 0. For ionic_tx_tso(), there's an actual possibility that
we leave the buffers mapped, so fix this by introducing the helper
function ionic_tx_desc_unmap_bufs(). This function is also re-used
in ionic_tx_clean().
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when a request for add/deleting a filter is made when
ionic_heartbeat_check() returns failure the driver will be overly
verbose about failures, especially when these are usually temporary
fails and the request will be retried later. An example of this is
a filter add when the FW is in the middle of resetting:
IONIC_CMD_RX_FILTER_ADD (31) failed: IONIC_RC_ERROR (-6)
rx_filter add failed: ADDR 01:80:c2:00:00:0e
Fix this by checking for -ENXIO and other error values on filter
request fails before printing the error message. Add similar
checking to the delete filter code.
Fixes: f91958cc96 ("ionic: tame the filter no space message")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when an administrator configures a VF via ndo_set_vf*,
the driver will send the set command to FW and then update the
cached value. The cached value is then used when reporting
VF info via ndo_get_vf_config.
A problem is that the VF info may have been updated between
the last ndo_set_vf* and ndo_get_vf_info commands via some
other method, i.e. a VF changes its MAC address (assuming it's
allowed to do so) and since this is all managed by the FW,
this new value won't be reflected in the PF's cache of values.
To fix this, update the driver to always get the latest VF
information by making use of the IONIC_CMD_VF_GETATTR dev
command. The FW may not support getting all the attributes for
IONIC_CMD_VF_GETATTR, so the driver will only update the cached
VF config members if their associated IONIC_CMD_VF_GETATTR
was successful. Otherwise the cached VF config members will
remain the same as what was set in ndo_set_vf*.
Fixes: fbb39807e9 ("ionic: support sr-iov operations")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dev commands fail, an error message will always be printed,
which may be overly alarming the to system administrators,
especially if the driver shouldn't be printing the error due
to some unsupported capability.
Similar to recent adminq request changes, we can update the
dev command interface with the ability to selectively print
error messages to allow the driver to prevent printing errors
that are expected.
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes went into the driver to allow flexibility when
printing error messages. Unfortunately this had the unexpected
consequence of printing confusing messages like the following:
IONIC_CMD_RX_FILTER_ADD (31) failed: IONIC_RC_SUCCESS (-6)
In cases like this the completion of the admin queue command never
completes, so the completion status is 0, hence IONIC_RC_SUCCESS
is printed even though the command clearly failed. For example,
this could happen when the driver tries to add a filter and at
the same time the FW goes through a reset, so the AQ command
never completes.
Fix this by forcing the FW completion status to IONIC_RC_ERROR
in cases where we never get the completion.
Fixes: 8c9d956ab6 ("ionic: allow adminq requests to override default error message")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we print the TIMEOUT string if we had a timeout
error, rather than printing the wrong status.
Fixes: 8c9d956ab6 ("ionic: allow adminq requests to override default error message")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IONIC_EVENT_RESET is received, we only need to start the
fw_down process if we aren't already down, and we need to be
sure to set the FW_STOPPING state on the way.
If this is how we noticed that FW was stopped, it is most
likely from a FW update, and we'll see a new FW generation.
The update happens quickly enough that we might not see
fw_status==0, so we need to be sure things get restarted when
we see the fw_generation change.
Fixes: d2662072c0 ("ionic: monitor fw status generation")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Between fw running and fw actually stopped into reset, we need
a fw_stopping concept to catch and block some actions while
we're transitioning to FW_RESET state. This will help to be
sure the fw_up task is not scheduled until after the fw_down
task has completed.
On some rare occasion timing, it is possible for the fw_up task
to try to run before the fw_down task, then not get run after
the fw_down task has run, leaving the device in a down state.
This is possible if the watchdog goes off in between finding the
down transition and starting the fw_down task, where the later
watchdog sees the FW is back up and schedules a fw_up task.
Fixes: c672412f61 ("ionic: remove lifs on fw reset")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible the FW is already shutting down while the driver is being
removed and/or when the driver is going through reset. This can cause
unexpected/unnecessary errors to be printed:
eth0: DEV_CMD IONIC_CMD_PORT_RESET (12) error, IONIC_RC_ERROR (29) failed
eth1: DEV_CMD IONIC_CMD_RESET (3) error, IONIC_RC_ERROR (29) failed
Fix this by checking the FW status register before issuing the reset
commands.
Also, since err may not be assigned in ionic_port_reset(), assign it a
default value of 0, and remove an unnecessary log message.
Fixes: fbfb803153 ("ionic: Add hardware init and device commands")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull the watchdog init code out to a separate bite-sized
function. Code cleaning for now, will be a useful change in
the near future.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The watchdog expects the lif to fully exist when it goes off,
so lets not start the watchdog until all is ready in case there
is some quirky time dialation that makes probe take multiple
seconds.
Fixes: 089406bc5a ("ionic: add a watchdog timer to monitor heartbeat")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse seems to have gotten a little more picky lately and
we need to revisit this bit of code to make sparse happy.
warning: incorrect type in initializer (different address spaces)
expected union ionic_dev_cmd_regs *regs
got union ionic_dev_cmd_regs [noderef] __iomem *dev_cmd_regs
warning: incorrect type in argument 2 (different address spaces)
expected void [noderef] __iomem *
got unsigned int *
warning: incorrect type in argument 1 (different address spaces)
expected void volatile [noderef] __iomem *
got union ionic_dev_cmd *
Fixes: d701ec326a ("ionic: clean up sparse complaints")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
commit 077cdda764 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
commit 31108d142f ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
commit 4390c6edc0 ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
https://lore.kernel.org/all/20211229065352.30178-1-saeed@kernel.org/
net/smc/smc_wr.c
commit 49dc9013e3 ("net/smc: Use the bitmap API when applicable")
commit 349d43127d ("net/smc: fix kernel panic caused by race of smc_sock")
bitmap_zero()/memset() is removed by the fix
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When allocated, this bitmap is not initialized. Only the first bit is set a
few lines below.
Use bitmap_zalloc() to make sure that it is cleared before being used.
Fixes: 6461b446f2 ("ionic: Add interrupts and doorbells")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/6a478eae0b5e6c63774e1f0ddb1a3f8c38fa8ade.1640527506.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cai Huoqing