The user is allowed to change beacon tx rate (HT/VHT/HE) from hostapd.
This information needs to be passed to the driver when the rate control
is offloaded to the firmware. The driver capability of allowing beacon
rate is already validated in cfg80211, so simply passing the rate
information to the driver is enough.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Link: https://lore.kernel.org/r/1601762658-15627-1-git-send-email-rmanohar@codeaurora.org
[adjust commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
last_rate is initialized to zero by sta_info_alloc(), but
this indicates legacy bitrate for the last TX rate (and
invalid for the last RX rate). To avoid a warning when
decoding the last rate as legacy (before a data frame
has been sent), initialize them as S1G MCS.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20201005164522.18069-2-thomas@adapt-ip.com
[rename to ieee80211_s1g_sta_rate_init(), seems more appropriate]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even though a driver or mac80211 shouldn't produce a
legacy bitrate if sband->bitrates doesn't exist, don't
crash if that is the case either.
This fixes a kernel panic if station dump is run before
last_rate can be updated with a data frame when
sband->bitrates is missing (eg. in S1G bands).
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20201005164522.18069-1-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_determine_chantype(), the sband->ht_cap was
being processed before S1G Operation element. Since the
HT capability element should not be present on the S1G
band, avoid processing potential garbage by moving the
call to ieee80211_apply_htcap_overrides() to after the S1G
block.
Also, in case of a missing S1G Operation element, we would
continue trying to process non-S1G elements (and return
with a channel width of 20MHz). Instead, just assume
primary channel is equal to operating and infer the
operating width from the BSS channel, then return.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20201001174748.24520-1-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow drivers to request that interface-iterator does NOT iterate
over interfaces that are not sdata-in-driver. This will allow
us to fix crashes in ath10k (and possibly other drivers).
To summarize Johannes' explanation:
Consider
add interface wlan0
add interface wlan1
iterate active interfaces -> wlan0 wlan1
add interface wlan2
iterate active interfaces -> wlan0 wlan1 wlan2
If you apply this scenario to a restart, which ought to be functionally
equivalent to the normal startup, just compressed in time, you're
basically saying that today you get
add interface wlan0
add interface wlan1
iterate active interfaces -> wlan0 wlan1 wlan2 << problem here
add interface wlan2
iterate active interfaces -> wlan0 wlan1 wlan2
which yeah, totally seems wrong.
But fixing that to be
add interface wlan0
add interface wlan1
iterate active interfaces ->
<nothing>
add interface wlan2
iterate active interfaces -> <nothing>
(or
maybe -> wlan0 wlan1 wlan2 if the reconfig already completed)
This is also at least somewhat wrong, but better to not iterate
over something that exists in the driver than iterate over something
that does not. Originally the first issue was causing crashes in
testing with lots of station vdevs on an ath10k radio, combined
with firmware crashing.
I ran with a similar patch for years with no obvious bad results,
including significant testing with ath9k and ath10k.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20200922191957.25257-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a frame was acked and probe frames were sent, the connection monitoring
needs to be reset, otherwise it will keep probing until the connection is
considered dead, even though frames have been acked in the mean time.
Fixes: 9abf4e4983 ("mac80211: optimize station connection monitor")
Reported-by: Georgi Valkov <gvalkov@abv.bg>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200927105605.97954-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The changes required for associating in S1G are:
- apply S1G BSS channel info before assoc
- mark all S1G STAs as QoS STAs
- include and parse AID request element
- handle new Association Response format
- don't fail assoc if supported rates element is missing
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-15-thomas@adapt-ip.com
[pass skb to ieee80211_add_aid_request_ie(), remove unused variable 'bss']
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G beacons are 802.11 Extension Frames, so the fixed
header part differs from regular beacons.
Add a handler to process S1G beacons and abstract out the
fetching of BSSID and element start locations in the
beacon body handler.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-14-thomas@adapt-ip.com
[don't rename, small coding style cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
minstrel_ht is confused by the lack of sband->bitrates,
and S1G will likely require a unique RC algorithm, so
avoid rate init for now if STA is on the S1G band.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-13-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G doesn't have legacy (sband->bitrates) rates, only MCS.
For now, just send a frame at MCS 0 if a low rate is
requested. Note we also redefine (since we're out of TX
flags) TX_RC_VHT_MCS as TX_RC_S1G_MCS to indicate an S1G
MCS. This is probably OK as VHT MCS is not valid on S1G
band and vice versa.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-12-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For now just skip the duration calculation for frames
transmitted on the S1G band and avoid a warning.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-11-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G allows listen interval up to 2^14 * 10000 beacon
intervals. In order to do this listen interval needs a
scaling factor applied to the lower 14 bits. Calculate
this and properly encode the listen interval for S1G STAs.
See IEEE802.11ah-2016 Table 9-44a for reference.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-10-thomas@adapt-ip.com
[move listen_int_usf into function using it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit finds the correct offset for Information
Elements in S1G beacon frames so they can be reported in
scan results.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-8-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Include the S1G Capabilities element in an association
request, and support the cfg80211 capability overrides.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-5-thomas@adapt-ip.com
[pass skb to ieee80211_add_s1g_capab_ie(), small code style edits]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An S1G BSS can beacon at either 1 or 2 MHz and the channel
width is unique to a given frequency. Ignore scan channel
width for now and use the allowed channel width.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When deleting a channel context, mac80211 would assing
NL80211_CHAN_WIDTH_20_NOHT as the default channel width.
This is wrong in S1G however, so instead get the allowed
channel width for a given channel.
Fixes eg. configuring strange (20Mhz) width during a scan
on the S1G band.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-2-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support 6 GHz scanning, by
* a new scan flag to scan for colocated BSSes advertised
by (and found) APs on 2.4 & 5 GHz
* doing the necessary reduced neighbor report parsing for
this, to find them
* adding the ability to split the scan request in case the
device by itself cannot support this.
Also add some necessary bits in mac80211 to not break with
these changes.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200918113313.232917c93af9.Ida22f0212f9122f47094d81659e879a50434a6a2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Because we can miss AP wakeup (beacon) while scanning other channels,
it's better go into wakeup state and inform the AP of that upon
returning to the operating channel, rather than staying asleep and
waiting for the next TIM indicating traffic for us.
This saves precious time, especially when we only have 200ms inter-
scan period for monitoring the active connection.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1593420923-26668-1-git-send-email-loic.poulain@linaro.org
[rewrite commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds mac80211 support to configure unsolicited
broadcast probe response transmission for in-band discovery in 6GHz.
Changes include functions to store and retrieve probe response template,
and packet interval (0 - 20 TUs).
Setting interval to 0 disables the unsolicited broadcast probe response
transmission.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/010101747a946b35-ad25858a-1f1f-48df-909e-dc7bf26d9169-000000@us-west-2.amazonses.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When trying to associate to an AP support 180 or 80+80 MHz on 6 GHz with a
STA that only has 80 Mhz support the cf2 field inside the chandef will get
set causing the association to fail when trying to validate the chandef.
Fix this by checking the support flags prior to setting cf2.
Fixes: 57fa5e85d5 ("mac80211: determine chandef from HE 6 GHz operation")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200918115304.1135693-1-john@phrozen.org
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some APs (e.g. Asus RT-AC88U) have been observed to report an HT MSDU size
limit of 3839 and a VHT limit of 7991. These APs can handle bigger frames
than 3839 bytes just fine, so we should remove the VHT limit based on the
HT capabilities. This improves tx throughput.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200916164611.8022-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the newly added ieee80211_set_vif_encap_ops declaration.
No further code changes.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-15-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For encap-offloaded packets, ieee80211_free_txskb cannot be used, since it
does not have the vif pointer.
Using ieee80211_tx_status_ext for this purpose has the advantage of being able
avoid an extra station lookup for AQL
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-12-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make ieee80211_tx_status_8023 call ieee80211_tx_status_ext, similar to
ieee80211_tx_status.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-11-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Calling mod_timer for every rx/tx packet can be quite expensive.
Instead of constantly updating the timer, we can simply let it run out
and check the timestamp of the last ACK or rx packet to re-arm it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-9-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to unify the tx status path, the hw 802.11 encapsulation flag
needs to survive the trip to the tx status call.
Since we don't have any free bits in info->flags, we need to move one.
IEEE80211_TX_INTFL_NEED_TXPROCESSING is only used internally in mac80211,
and only before the call into the driver.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-10-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All drivers using airtime fairness are calling ieee80211_sta_register_airtime
directly, now they must. Document this as well.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-8-nbd@nbd.name
[johannes: update the documentation to suit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move redundant functionality from __ieee80211_tx_status into
ieee80211_tx_status_ext. Preparation for unifying with the 802.3 tx status
codepath.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-7-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current API (which lets the driver turn on/off per vif directly) has a
number of limitations:
- it does not deal with AP_VLAN
- conditions for enabling (no tkip, no monitor) are only checked at
add_interface time
- no way to indicate 4-addr support
In order to address this, store offload flags in struct ieee80211_vif
(easy to extend for decap offload later). mac80211 initially sets the enable
flag, but gives the driver a chance to modify it before its settings are
applied. In addition to the .add_interface op, a .update_vif_offload op is
introduced, which can be used for runtime changes.
If a driver can't disable encap offload at runtime, or if it has some extra
limitations, it can simply override the flags within those ops.
Support for encap offload with 4-address mode interfaces can be enabled
by setting a flag from .add_interface or .update_vif_offload.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-6-nbd@nbd.name
[resolved conflict with commit aa2092a9ba ("ath11k: add raw mode and
software crypto support")]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This simplifies the checks in the encap offload tx handler and allows using
it in cases where software crypto is used for multicast packets, e.g. when
using an AP_VLAN.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-4-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update the last_tx timestamp to avoid tearing down the aggregation session
early. Fall back to the slow path if the session setup is still running
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When converting from struct ieee80211_tx_rate to ieee80211_rx_status,
there was one check missing to fill in the bandwidth for 160 MHz
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200915085945.3782-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The unit of the return value of ieee80211_get_rate_duration is nanoseconds, not
microseconds. Adjust the duration checks to account for that.
For higher data rates, allow larger estimated aggregation sizes, and add some
values for HE as well, which can use much larger aggregates.
Since small packets with high data rates can now lead to duration values too
small for info->tx_time_est, return a minimum of 4us.
Fixes: f01cfbaf9b ("mac80211: improve AQL aggregation estimation for low data rates")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200915085945.3782-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We want to reuse the functions and structs for other counters such as BSS
color change. Rename them to more generic names.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200811080107.3615705-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When running a large number of packets per second with a high data rate
and long A-MPDUs, the packet loss threshold can be reached very quickly
when the link conditions change. This frequently shows up as spurious
disconnects.
Mitigate false positives by using a similar logic for regular stations
as the one being used for TDLS, though with a more aggressive timeout.
Packet loss events are only reported if no ACK was received for a second.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200808172542.41628-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
