In the function of hisi_sas_init_device(), we added ops->hardreset() to
clear affiliation of STP target port or handle [STP pending] state.
Function hisi_sas_init_device() will be called when a device is found or
during controller reset. At controller reset, we call
hisi_sas_init_device() to re-init the disks, so calling hardreset() is
unnecessary and it also will cause some delay at controller reset.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is to switch HW all error handling from PCI AER to MSI interrupt
due to non-standard PCI implementation. All HW errors which were being
reported through PCI AER can be reported through MSI interrupt also.
Do two things to complete the switch:
1. Notify FW to switch to MSI handling through ACPI DSM.
2. Add MSI handling for some hw errors, ECC errors and poison errors (we
also call some of them AXI reuser error). They were handled only through
PCI AER before.
For old FW reporting PCI AER events, the PCI AER handler will see that the
driver on longer support AER, and will leave the device in offlined state,
which is safe.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit 8b8d665315 ("scsi: hisi_sas: make SAS address of SATA disks
unique"), we ensured that each SATA disk in the system has a unique SAS
address, even if it is fake. That was for v2 hw.
Add this for v3 hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function hisi_sas_init_device(), the log is as follows when error for
hardreset:
hisi_sas_v3_hw 0000:74:02.0: SATA disk hardreset fail: 0xffffffed
Actually if hardreset failed, its return value is negative, so change the
print format from %x to %d.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit efdcad62e7 ("scsi: hisi_sas: Set PHY linkrate when
disconnected"), we use the sas_phy_data.enable flag to track whether the
PHY was enabled or not, so that we know if we should set the PHY negotiated
linkrate at SAS_LINK_RATE_UNKNOWN or SAS_PHY_DISABLED.
However, it is not proper to use sas_phy_data.enable, since it is only set
when libsas attempts to set the PHY disabled/enabled; hence, it may not
even have an initial value.
As a solution to this problem, introduce hisi_sas_phy.enable to track
whether the PHY is enabled or not, so that we can set the negotiated
linkrate properly when the PHY comes down.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently there are two scenarioes which may cause PHY state of hardware
(which is 0) is inconsistent with the state held in software:
- Unplug SAS wire before get_phys_state when SAS controller reset, then the
interrupts of phy down are ignored, phy state is 0 before reset, and it
also gets 0 after reset, so phy down doesn't occur even if unplugged SAS
wire;
- For v3 hw later version, it will close bus when 2 bit ECC error occurs.
So if unplug SAS wire at that time, interrupts of phy down also not
occur. So at last it will cause host reset. It also get phy state 0
before and after reset, the same issue occurs.
To solve it, use hisi_sas_phy_down() directly in rescan topology function.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add host reset interface to make it easier for testing the host reset
feature.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We have a few submissions for 5.2 that depend on fixes merged post
5.1-rc1. Merge the fixes branch into queue.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the FC-NVMe driver is leverating the SCSI FC transport class to
access the remote ports. Which means that all FC-NVMe remote ports will be
visible to the fc transport layer, but due to missing definitions the port
roles will always be 'unknown'. This patch adds the missing definitions to
the fc transport class to that the port roles are correctly displayed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The error return path via label rel_resource checks for a non-null skb
before free'ing it. However, skb is always null at this exit path, so the
null check and the free are redundant and can be removed. Removing this
allows the original goto's to rel_resource to be cleaned up; the first can
be replaced by a return of -EINVAL, the second can be replaced by a more
appropriate -ENOMEM return and fix a memory leak by freeing csk->atid.
Addresses-Coverity: ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Only include those header files that are needed by the code in this source
file.
[mkp: include build fix from Bart for SPARC]
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If scsi cmd sglist is not suitable for DDP then csiostor driver uses
preallocated buffers for DDP, because of this data copy is required from
DDP buffer to scsi cmd sglist before calling ->scsi_done().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make sure that resources are only unregistered after the users of these
resources have been unregistered. Only unregister the character device if
registration of it succeeded.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If module initialization fails after the character device has been
registered, unregister the character device. Additionally, avoid
duplicating error path code.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Fixes: 6a03b4cd78 ("[SCSI] qla2xxx: Add char device to increase driver use count") # v2.6.35.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch makes the code easier to read but does not change any
functionality.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make qla2x00_process_response_queue() easier to read by splitting this
function. This patch does not change any functionality.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move the SCSI host template definition after the definition of the
functions that it references. Remove the forward declarations that became
unnecessary by that change. This patch does not change any functionality.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that sparse complains that a declaration is missing.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make the code easier to read by avoiding to use a hard-coded constant. This
patch does not change any functionality.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since qla2xxx_queuecommand() no longer takes the SCSI host lock, remove a
comment that refers to the host lock.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make qla2x00_get_host_fabric_name() slightly faster by changing a stack
array into a static array. Declare that array const now that the
wwn_to_u64() argument pointer has been declared const.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a spelling mistake in a ql_log message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support to recognize FPIN ELS's that are received. When
one is received, the fc transport will be called to handle the the FPIN.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a new event type - an FPIN event.
Add a new routine, fc_host_fpin_rcv(), that lldd's call when an FPIN is
received. The routine processes the fpin payload. For now, the routine
only logs an FPIN event.
Signed-off-by: Muneendra <muneendra.kumar@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are two routines generating transport events that do the same thing
with only a couple of values set differently.
Refactor so there's a single routine doing the netlink operations to send
the event. All the differences are passed as arguments. Export the symbol
so the generic routine can be called by llds.
Modify the existing two event routines to use the helper.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the following compiler warning is reported with
CONFIG_NVME_FC=n:
drivers/scsi/lpfc/lpfc_nvme.c:2140:1: warning: 'lpfc_nvme_lport_unreg_wait' defined but not used [-Wunused-function]
lpfc_nvme_lport_unreg_wait(struct lpfc_vport *vport,
^~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 3999df75bc ("scsi: lpfc: Declare local functions static")
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The memory return by kzalloc() has already be set to zero, so remove
useless memset(0).
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds an additional PHY initialization, required for M31 PHY when
used with Cadence UFS HC. A new compatible string has been added for this
purpose.
[mkp: nuke superfluous status return]
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The pointer value is initialized as &hba->vreg_info, and it's never
changed. It's not necessary to check the pointer is null or not.
Signed-off-by: Zeng Guangyue <zengguangyue@hisilicon.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/qedf/qedf_fip.c: In function 'qedf_fcoe_send_vlan_req':
drivers/scsi/qedf/qedf_fip.c:22:6: warning:
variable 'fr_len' set but not used [-Wunused-but-set-variable]
It's never used since introduction and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename the functions pm8001_chip_is_our_interupt,
pm80xx_chip_is_our_interupt and function pointer is_our_interrupt to fix
spelling mistakes.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When macro PM8001_USE_MSIX is defined there are redundant dead code calls
to pm8001_chip_intx_interrupt_{enable|disable} and pm8001_cr32.
Clean this up for the defined PM8001_USE_MSIX and undefined
PM8001_USE_MSIX cases.
[mkp: squashed two patches]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch converts driver wait time from using msleep to
wair_event_timeout to prevent race condition.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch allows driver to unload using "modprobe -r" when FC-NVMe LUNs
are connected.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch sets remote_port_devloss value to 0. This indicates to FC-NVMe
transport that driver is unloading and transport should not retry.
Fixes: e476fe8af5 ("scsi: qla2xxx: Fix unload when NVMe devices are configured")
Cc: stable@vger.kernel.org
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clean up fcport list and loopid in one place and iterate through for loop.
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add mutex protection to prevent driver from freeing the FW dump buffer
while the extraction is in progress.
[mkp: commit desc]
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If fw dump buffer size changes and there is an existing fw dump, then save
the old dump in the newly allocated buffer.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Recent ISPs have larger and more complex flash-write semantics
(secure-access and signing). The BSG interfaces support these semantics for
all ISPs and is exclusively used by QLogic user-space tools. Limit
flash-write operations to ISPs <= 25xx.
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit e6f77540c0 ("scsi: qla2xxx: Fix an integer overflow in sysfs
code") incorrectly set 'optrom_region_size' to 'start+size', which can
overflow option-rom boundaries when 'start' is non-zero. Continue setting
optrom_region_size to the proper adjusted value of 'size'.
Fixes: e6f77540c0 ("scsi: qla2xxx: Fix an integer overflow in sysfs code")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Abort thread wakeups, on some wqe types, are not happening. The thread
wakeup logic is dependent upon the LPFC_DRIVER_ABORTED flag. However, on
these wqes, the completion handler running prior to the io completion
routine ends up clearing the flag.
Rework the wakeup logic to look at a non-null waitq element which must be
set if the abort thread is waiting. This is reverting the change in the
indicated patch.
Fixes: c2017260ee ("scsi: lpfc: Rework locking on SCSI io completion")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reduce the default VMbus channel ring buffer size for storvsc SCSI devices
from 1 Mbyte to 128 Kbytes. Measurements show that ring buffer sizes above
128 Kbytes do not increase performance even at very high IOPS rates, so
don't waste the memory. Also remove the dependence on PAGE_SIZE, since the
ring buffer size should not change on architectures where PAGE_SIZE is not
4 Kbytes.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the number of sub-channels offered by Hyper-V is >= the number of CPUs
in the VM, calculate the correct number of sub-channels. The current code
produces one too many.
This scenario arises only when the number of CPUs is artificially
restricted (for example, with maxcpus=<n> on the kernel boot line), because
Hyper-V normally offers a sub-channel count < number of CPUs. While the
current code doesn't break, the extra sub-channel is unbalanced across the
CPUs (for example, a total of 5 channels on a VM with 4 CPUs).
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Blacklist "Universal Xport" LUN. It's used for in-band storage array
management. Also add model to the rdac dh family.
Cc: Martin Wilck <mwilck@suse.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: NetApp RDAC team <ng-eseries-upstream-maintainers@netapp.com>
Cc: Christophe Varoqui <christophe.varoqui@opensvc.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: SCSI ML <linux-scsi@vger.kernel.org>
Cc: DM ML <dm-devel@redhat.com>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With FC-NVMe enabled, driver does not support T10 DIF/DIX. This patch
disables T10-PI information when ql2xnvmeenable is set.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch increases max_sgl_segments value from 128 to the maximum
supported which is 1024. Increasing max_sgl_segments will allow the driver
to support larger I/O sizes
[mkp: commit desc tweak]
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver maintains state machine for processing and completing switch
commands. This patch resets FCF_ASYNC_{SENT|ACTIVE} flag to indicate if the
previous command is active or sent, in order for next GPSC command to
advance the state machine.
[mkp: commit desc typo]
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch sets QPair pointer to NULL to prevent abort command racing ahead
of normal command completion handling during scsi_done call.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch tries to address race condition between abort handler and
completion handler. When scsi command result is set by both abort and
completion handler, scsi_done() is only called after refcount on SRB
structure goes to zero. The abort handler sets this result prematurely even
when the refcount is non-zero value. Fix this by setting SCSI cmd->result
before scsi_done() is called.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that a kernel warning appears when smp_processor_id() is
called with preempt debugging enabled.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove those functions that are not called from outside the removed
functions.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality but avoids that the compiler
complains about set-but-not-used variables when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arrays should be defined in .c files instead of in a header file. This
patch reduces the size of the lpfc kernel module.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler warns about missing fall-through
annotation when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoid that smatch complains about misleading indentation.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler complains about missing declarations
when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
"<name>-fixed-regulator" device tree property can be safely removed because
below things are fixed or resolved,
1. "<name>-max-microamp" becomes optional property: Undefined
"<name>-max-microamp" will not cause initialization fail if
"<name>-fixed-regulator" is not defined.
2. Current switching operation (by regulator_set_load) now has rules:
Regulators will have undefined current limit if "<name>-fixed-regulator"
is not defined. But this is safe because only regulator which has
configured current limit from "<name>-max-microamp" property is allowed
to change its load.
Although "<name>-fixed-regulator" is not used in any dt-bindings in tree,
this patch is still safe for regulators already defined
"<name>-fixed-regulator". To be more clear, if a regulator defined
"<name>-fixed-regulator" before, the behavior difference after this patch
is,
1. "<name>-max-microamp":
If a regulator defined "<name>-fixed-regulator", it is not necessary
to define "<name>-max-microamp" property in device tree and it is
expected to have an undefined current limit, i.e., "max_uA" field
is zero in struct ufs_vreg. This is exactly the same as patched.
2. "vcc-supply-1p8" or volatge range settings:
* For vcc, vccq or vccq2, these three regulators shall not define
"<name>-fixed-regulator" because defining it will lead to
undefined voltage range and thus voltage switching will be
unexpected.
* For other regulators with undefined voltage range, voltage range
will be still undefined after patched.
Therefore this patch is safe for all existed regulators with
"<name>-fixed-regulator" property already defined.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In dt-bindings for ufs, "<name>-max-microamp" property indicates current
limit and is mandatory if "<name>-fixed-regulator" is not defined on a
specified regulator.
However, in some platforms, regulators without "<name>-fixed-regulator"
property may not need to define their current limit because they may want
to define voltage range only for proper voltage switching in different
power modes, especially for vcc, vccq or vccq2.
Currently missing "<name>-max-microamp" property in device tree will lead
initialization to fail, thus such limitation shall be resolved to tolerate
this kind of regulators.
After resolving this, regulators without "<name>-max-microamp" property
will have undefined "max current" value, i.e., zero value in "max_uA" field
in struct ufs_vreg. Because we do bypass current switching operation (by
regulator_set_load) in case of undefined current limit, this patch shall be
safe.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a regulator has "<name>-fixed-regulator" property in device
tree, it will skip current limit initialization. This lead to a zero
"max_uA" value in struct ufs_vreg.
However, "regulator_set_load" operation shall be required on regulators
which have valid current limits, otherwise a zero "max_uA" set by
"regulator_set_load" may cause unexpected behavior when this regulator is
enabled or set as high power mode.
Similarly, in device's icc_level configuration flow, the target icc_level
shall be updated if regulator also has valid current limit, otherwise a
wrong icc_level will be calculated by zero "max_uA" and thus causes
unexpected results after it is written to device.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For regulators used by UFS, vcc, vccq and vccq2 will have voltage range
initialized by ufshcd_populate_vreg(), however other regulators may have
undefined voltage range if dt-bindings have no such definition.
In above undefined case, both "min_uV" and "max_uV" fields in ufs_vreg
struct will be zero values and these values will be configured on
regulators in different power modes.
Currently this may have no harm if both "min_uV" and "max_uV" always keep
"zero values" because regulator_set_voltage() will always bypass such
invalid values and return "good" results.
However improper values shall be fixed to avoid potential bugs. Simply
bypass voltage configuration if voltage range is not defined.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are two fields related to regulator current limit in struct ufs_vreg:
"min_uA" and "max_uA".
"max_uA" is probed by "<name>-max-microamp" property from device tree and
used for
- regulator_set_load operations
- icc_level configuration in device
However "min_uA" field is not used anywhere, thus we can remove it.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The rc variable is not needed in bnx2fc_abts_cleanup(). Remove it and
just return SUCCESS.
[mkp: commit desc]
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The nvm_image is a large struct qedi_nvm_iscsi_image object of over 24K so
don't declare it on the stack just for a sizeof requirement; use sizeof on
struct qedi_nvm_iscsi_image instead.
Fixes: c77a2fa3ff ("scsi: qedi: Add the CRC size within iSCSI NVM image")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- lport was getting used without initialization, initialize it to fix a
warning.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Handle refcount of rdata during error conditions.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Here is the relevant logs for the problem we are solving:
qedf_flush_active_ios:1707]:3: Flush active i/o's num=0x17 fcport=0xffff948168fbcc80 port_id=0x550200 scsi_id=0.
qedf_flush_active_ios:1708]:3: Locking flush mutex.
qedf_flush_active_ios:1758]:3: Not outstanding, xid=0xaaf, cmd_type=3 refcount=1.
qedf_flush_active_ios:1896]:3: Flushed 0x16 I/Os, active=0x1.
qedf_flush_active_ios:1901]:3: Flushed 0x16 I/Os, active=0x1 cnt=60.
qedf_send_rrq:295]:3: Sending RRQ orig io = ffffb48b8f7d7158, orig_xid = 0xaaf
qedf_initiate_els:37]:3: Sending ELS
qedf_initiate_els:68]:3: initiate_els els_req = 0xffffb48b8f6d3098 cb_arg = ffff948fd5e4de80 xid = 4c6
qedf_init_mp_req:2172]:3: Entered.
qedf_init_mp_task:727]:3: Initializing MP task for cmd_type=4
qedf_initiate_els:134]:3: Ringing doorbell for ELS req
qedf_flush_active_ios:1901]:3: Flushed 0x16 I/Os, active=0x2 cnt=20.
qedf_cmd_timeout:96]:3: ELS timeout, xid=0x4c6.
qedf_rrq_compl:186]:3: Entered.
qedf_rrq_compl:204]:3: rrq_compl: orig io = ffffb48b8f7d7158, orig xid = 0xaaf, rrq_xid = 0x4c6, refcount=1
qedf_flush_active_ios:1935]:3: Unlocking flush mutex.
qedf_upload_connection:1579]:3: Uploading connection port_id=550200.
We found an ABTS command for which CMD_OUTSTANDING was cleared (line 3).
For this command, delayed send_rrq was queued, but would take 10 secs to
execute. Adding capability to detect that (based on io_req->state that is
being introduced), and attempt to cancel rrq_work. If we succeed, we drop
the reference and free the io_req. If we cannot, then the els will get sent
out and we will wait for 10 secs for it to complete.
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
cmd_type is over written to QEDF_CLEANUP during cleanup, so check for
tm_flags.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- The flag will help in to figure out if io_req is cleaned or not.
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Command is already completed with underrun so no need to send ABTS.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- I/Os, aborts and tmf should not be queued if flush is in progress.
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Check proper values before servicing CVL.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The fc_rport_priv structure is reference counted, so we need to ensure that
the reference is increased before accessing the structure.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On completions where we do not have a bad scsi_cmnd pointer we should
return before the the label lest we do a double kref_put.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Wait for all the connections to get uploaded.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Check the validity of various pointers before processing.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
test_bit() is atomic, test_bit() || test_bit() is not. So protect
consecutive bit tests with a lock to avoid races.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fc_rport_create() needs to be called with disc_mutex held. And we should
re-assign the 'rdata' pointer in case it got changed.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qedf_xmit() calls fc_rport_lookup(), but discards the returned rdata
structure almost immediately without decreasing the refcount. This leads
to a refcount leak and the rdata never to be freed.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Check if link is UP before sending and processing any packets on wire.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When receiving an unsolicited frame we could crash on a list traversal in
fc_rport_lookup while searching the rport which is associated with our
lport.
Initialize the lport's discovery node after allocating the lport in
__qedf_probe().
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Correct memory barriers to make sure all cmnds are flushed.
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- If a TMF and cleanup are issued at the same time they could cause a call
trace if issued against the same xid as the io_req->tm_done completion
is used for both.
- Set and clear cleanup bit in cleanup routine.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An I/O can be in any state when flush is called, it can be in abort,
waiting for abort, RRQ send and waiting or TMF send.
- HZ can be different on different architecture, correctly set abort
timeout value.
- Flush can complete the I/Os prematurely, handle refcount for aborted
I/Os and for which RRQ is pending.
- Differentiate LUN/TARGET reset, as cleanup needs to be send to firmware
accordingly.
- Add flush mutex to sync cleanup call from abort and flush routine.
- Clear abort/outstanding bit on timeout.
Signed-off-by: Shyam Sundar <shyam.sundar@marvell.com>
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The purpose of flush routine is to cleanup I/Os to the firmware and
complete them to scsi middle layer. This routine is invoked before
connection is uploaded because of rport going away.
- Don't process any I/Os, aborts, TMFs coming when flush in progress.
- Add flags to handle cleanup and release of I/Os because flush can
prematurely complete I/Os.
- Original command can get completed to driver when cleanup for same is
posted to firmware, handle this condition.
- Modify flush to handle I/Os in all the states like abort, TMF, RRQ and
timeouts.
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When mapping the pages from a scatter/gather list from the SCSI layer we
only need to follow these rules:
- Max SGEs for each I/O request is 256
- No size limit on each SGE
- No need to split OS provided SGEs to 4K before sending to firmware.
- Slow SGE is applicable only when:
- There are > 8 SGEs and any middle SGE is less than a page size (4K)
Make necessary changes so that driver follows these rules. Applicable only
for Write requests (not for Read requests). No need to check SGE address
alignment requirements (first, middle or last) before declaring slow SGE.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is currently an overlap where exchange IDs between what is used for
offloaded commands and by libfc for ELS commands. Correct this so that
exchange ID range is:
Offloaded requests: 0 to 0xfff
libfc requests: 0x1000 to 0xfffe
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No change to functionality. Simply make transport event messages a little
clearer, and rework CRQ format enums such that we have separate enums for
INIT messages and XPORT events.
[mkp: typo]
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Status and error codes are returned in big endian from the VIOS. The values
are translated into a human readable format when logged, but the values are
also logged. This patch byte swaps those values so that they are consistent
between BE and LE platforms.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The VIOS uses the SCSI_ERROR class to report PRLI failures. These errors
are indicated with the combination of a IBMVFC_FC_SCSI_ERROR return status
and 0x8000 error code. Add these codes to cmd_status[] with appropriate
human readable error message.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The text of messages logged with ibmvfc_log_error() always contain the term
"failed". In the case of cancelled commands during EH they are reported
back by the VIOS using error codes. This can be confusing to somebody
looking at these log messages as to whether a command was successfully
cancelled. The following real log message for example it is unclear if the
transaction was actaully cancelled.
<6>sd 0:0:1:1: Cancelling outstanding commands.
<3>sd 0:0:1:1: [sde] Command (28) failed: transaction cancelled (2:6) flags: 0 fcp_rsp: 0, resid=0, scsi_status: 0
Remove prefixing of "failed" to all error logged messages. The
ibmvfc_log_error() function translates the returned error/status codes to a
human readable message already.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns when it sees a logical not on the left side of a conditional
statement because it thinks the logical not should be applied to the whole
statement, not just the left side:
drivers/scsi/qla2xxx/qla_nx.c:3703:7: warning: logical not is only
applied to the left hand side of this comparison
[-Wlogical-not-parentheses]
This particular instance was already fixed by commit 0bfe7d3cae ("scsi:
qla2xxx: Simplify conditional check") upstream but it was reintroduced by
commit 3695310e37 ("scsi: qla2xxx: Update flash read/write routine") in
the 5.2/scsi-queue.
Fixes: 3695310e37 ("scsi: qla2xxx: Update flash read/write routine")
Link: https://github.com/ClangBuiltLinux/linux/issues/80
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit a83da8a450 ("scsi: sd: Optimal I/O size should be a multiple
of physical block size") split one conditional into several separate
statements in an effort to provide more accurate warning messages when
a device reports a nonsensical value. However, this reorganization
accidentally dropped the precondition of the reported value being
larger than zero. This lead to a warning getting emitted on devices
that do not report an optimal I/O size at all.
Remain silent if a device does not report an optimal I/O size.
Fixes: a83da8a450 ("scsi: sd: Optimal I/O size should be a multiple of physical block size")
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: <stable@vger.kernel.org>
Reported-by: Hussam Al-Tayeb <ht990332@gmx.com>
Tested-by: Hussam Al-Tayeb <ht990332@gmx.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The scsi_end_request() function calls scsi_cmd_to_driver() indirectly and
hence needs the disk->private_data pointer. Avoid that that pointer is
cleared before all affected I/O requests have finished. This patch avoids
that the following crash occurs:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
scsi_mq_uninit_cmd+0x1c/0x30
scsi_end_request+0x7c/0x1b8
scsi_io_completion+0x464/0x668
scsi_finish_command+0xbc/0x160
scsi_eh_flush_done_q+0x10c/0x170
sas_scsi_recover_host+0x84c/0xa98 [libsas]
scsi_error_handler+0x140/0x5b0
kthread+0x100/0x12c
ret_from_fork+0x10/0x18
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Jason Yan <yanaijie@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reported-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use dd to test a SCSI device:
1. echo "blocked" >/sys/block/sda/device/state
2. dd if=/dev/sda of=/mnt/t.log bs=1M count=10
3. echo "running" >/sys/block/sda/device/state
dd should finish this work after step 3, but it hangs.
After step2, the call chain is this:
blk_mq_dispatch_rq_list-->scsi_queue_rq-->prep_to_mq
prep_to_mq will return BLK_STS_RESOURCE, and scsi_queue_rq will
transition it to BLK_STS_DEV_RESOURCE which means that driver can
guarantee that IO dispatch will be triggered in future when the
resource is available. Need to follow the rule if we set the device
state to running.
[mkp: tweaked commit description and code comment as suggested by Bart]
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make sd_probe() easier to read by inlining sd_probe_part2(). This patch
does not change any functionality.
Cc: Lee Duncan <lduncan@suse.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As explained during the 2018 LSF/MM session about increasing SCSI disk
probing concurrency, the problems with the current probing approach are as
follows:
- The driver core is unaware of asynchronous SCSI LUN probing.
wait_for_device_probe() waits for all asynchronous probes except
asynchronous SCSI disk probes.
- There is unnecessary serialization between sd_probe() and sd_remove().
This can lead to a deadlock.
Hence this patch that modifies the sd driver such that it uses the driver
core framework for asynchronous probing. The async domains and
get_device()/put_device() pairs that became superfluous due to this change
are removed.
This patch does not affect the time needed for loading the scsi_debug
kernel module with parameters delay=0 and max_luns=256.
This patch depends on commit ef0ff68351 ("driver core: Probe devices
asynchronously instead of the driver") that went upstream in kernel version
v5.1-rc1.
Cc: Lee Duncan <lduncan@suse.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a couple of statements that are incorrectly indented, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The variable len is not being inintialized and the uninitialized value is
being returned. However, this return path is never reached because the
default case in the switch statement returns -ENOSYS. Clean up the code by
replacing the return -ENOSYS with a break for the default case and
returning -ENOSYS at the end of the function. This allows len to be
removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case iscsi_lookup_endpoint fails, the fix returns -EINVAL to avoid NULL
pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/scsi/gdth.c:3662:6: warning: variable 'paddr' is used
uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
Don't attempt to call dma_free_coherent when buf is NULL (meaning that
we never called dma_alloc_coherent and initialized paddr), which avoids
this warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/402
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/pm8001/pm8001_hwi.c: In function 'mpi_smp_completion':
drivers/scsi/pm8001/pm8001_hwi.c:2901:6: warning:
variable 'param' set but not used [-Wunused-but-set-variable]
drivers/scsi/pm8001/pm8001_hwi.c: In function 'pm8001_bytes_dmaed':
drivers/scsi/pm8001/pm8001_hwi.c:3247:24: warning:
variable 'sas_ha' set but not used [-Wunused-but-set-variable]
They're never used since introduction, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a few windows during AER/EEH when we can access PCIe I/O mapped
registers. This will harden the access to insure we do not allow PCIe
access during errors
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Sagar Biradar <sagar.biradar@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang -Wuninitialized notices that on is_qla40XX we never allocate any DMA
memory in get_fw_boot_info() but attempt to free it anyway:
drivers/scsi/qla4xxx/ql4_os.c:5915:7: error: variable 'buf_dma' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
if (!(val & 0x07)) {
^~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5985:47: note: uninitialized use occurs here
dma_free_coherent(&ha->pdev->dev, size, buf, buf_dma);
^~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5915:3: note: remove the 'if' if its condition is always true
if (!(val & 0x07)) {
^~~~~~~~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5885:20: note: initialize the variable 'buf_dma' to silence this warning
dma_addr_t buf_dma;
^
= 0
Skip the call to dma_free_coherent() here.
Fixes: 2a991c2159 ("[SCSI] qla4xxx: Boot from SAN support for open-iscsi")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
clang -Wuninitialized incorrectly sees a variable being used without
initialization:
drivers/scsi/lpfc/lpfc_nvme.c:2102:37: error: variable 'localport' is uninitialized when used here
[-Werror,-Wuninitialized]
lport = (struct lpfc_nvme_lport *)localport->private;
^~~~~~~~~
drivers/scsi/lpfc/lpfc_nvme.c:2059:38: note: initialize the variable 'localport' to silence this warning
struct nvme_fc_local_port *localport;
^
= NULL
1 error generated.
This is clearly in dead code, as the condition leading up to it is always
false when CONFIG_NVME_FC is disabled, and the variable is always
initialized when nvme_fc_register_localport() got called successfully.
Change the preprocessor conditional to the equivalent C construct, which
makes the code more readable and gets rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.
1) Uses of size += snprintf(buf, SIZE - size, fmt, ...)
In this case, if snprintf would have written more characters than what the
buffer size (SIZE) is, then size will end up larger than SIZE. In later
uses of snprintf, SIZE - size will result in a negative number, leading
to problems. Note that size might already be too large by using
size = snprintf before the code reaches a case of size += snprintf.
2) If size is ultimately used as a length parameter for a copy back to user
space, then it will potentially allow for a buffer overflow and information
disclosure when size is greater than SIZE. When the size is used to index
the buffer directly, we can have memory corruption. This also means when
size = snprintf... is used, it may also cause problems since size may become
large. Copying to userspace is mitigated by the HARDENED_USERCOPY kernel
configuration.
The solution to these issues is to use scnprintf which returns the number of
characters actually written to the buffer, so the size variable will never
exceed SIZE.
Signed-off-by: Silvio Cesare <silvio.cesare@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building the ufs-mediatek module the following warning shows up:
WARNING: modpost: missing MODULE_LICENSE() in
drivers/scsi/ufs/ufs-mediatek.o
Rework to add MODULE_LICENSE,MODULE_AUTHOR and MODULE_DESCRIPTION.
Fixes: ddd90623ce ("scsi: ufs-mediatek: Add UFS support for Mediatek SoC chips")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During expander reset handling, the driver invokes kernel function
scsi_host_find_tag() to obtain outstanding requests associated with the
scsi host managed by the driver. Driver loops from tag value zero to hba
queue depth to obtain the outstanding scmds. But when blk-mq is enabled,
the block layer may return stale entry for one or more requests. This may
lead to kernel panic if the returned value is inaccessible or the memory
pointed by the returned value is reused.
Reference of upstream discussion:
https://patchwork.kernel.org/patch/10734933/
Instead of calling scsi_host_find_tag() API for each and every smid (smid
is tag +1) from one to shost->can_queue, now driver will call this API (to
obtain the outstanding scmd) only for those smid's which are outstanding at
the driver level.
Driver will determine whether this smid is outstanding at driver level by
looking into it's corresponding MPI request frame, if its MPI request frame
is empty, then it means that this smid is free and does not need to call
scsi_host_find_tag() for it. By doing this, driver will invoke
scsi_host_find_tag() for only those tags which are outstanding at the
driver level.
Driver will check whether particular MPI request frame is empty or not by
looking into the "DevHandle" field. If this field is zero then it means
that this MPI request is empty. For active MPI request DevHandle must be
non-zero.
Also driver will memset the MPI request frame once the corresponding scmd
is processed (i.e. just before calling
scmd->done function).
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The event pool used for queueing commands is destroyed fairly early in the
ibmvscsi_remove() code path. Since, this happens prior to the call so
scsi_remove_host() it is possible for further calls to queuecommand to be
processed which manifest as a panic due to a NULL pointer dereference as
seen here:
PANIC: "Unable to handle kernel paging request for data at address
0x00000000"
Context process backtrace:
DSISR: 0000000042000000 ????Syscall Result: 0000000000000000
4 [c000000002cb3820] memcpy_power7 at c000000000064204
[Link Register] [c000000002cb3820] ibmvscsi_send_srp_event at d000000003ed14a4
5 [c000000002cb3920] ibmvscsi_send_srp_event at d000000003ed14a4 [ibmvscsi] ?(unreliable)
6 [c000000002cb39c0] ibmvscsi_queuecommand at d000000003ed2388 [ibmvscsi]
7 [c000000002cb3a70] scsi_dispatch_cmd at d00000000395c2d8 [scsi_mod]
8 [c000000002cb3af0] scsi_request_fn at d00000000395ef88 [scsi_mod]
9 [c000000002cb3be0] __blk_run_queue at c000000000429860
10 [c000000002cb3c10] blk_delay_work at c00000000042a0ec
11 [c000000002cb3c40] process_one_work at c0000000000dac30
12 [c000000002cb3cd0] worker_thread at c0000000000db110
13 [c000000002cb3d80] kthread at c0000000000e3378
14 [c000000002cb3e30] ret_from_kernel_thread at c00000000000982c
The kernel buffer log is overfilled with this log:
[11261.952732] ibmvscsi: found no event struct in pool!
This patch reorders the operations during host teardown. Start by calling
the SRP transport and Scsi_Host remove functions to flush any outstanding
work and set the host offline. LLDD teardown follows including destruction
of the event pool, freeing the Command Response Queue (CRQ), and unmapping
any persistent buffers. The event pool destruction is protected by the
scsi_host lock, and the pool is purged prior of any requests for which we
never received a response. Finally, move the removal of the scsi host from
our global list to the end so that the host is easily locatable for
debugging purposes during teardown.
Cc: <stable@vger.kernel.org> # v2.6.12+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For each ibmvscsi host created during a probe or destroyed during a remove
we either add or remove that host to/from the global ibmvscsi_head
list. This runs the risk of concurrent modification.
This patch adds a simple spinlock around the list modification calls to
prevent concurrent updates as is done similarly in the ibmvfc driver and
ipr driver.
Fixes: 32d6e4b6e4 ("scsi: ibmvscsi: add vscsi hosts to global list_head")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/scsi/ufs/ufs-mediatek.c:112:7: warning: variable 'ret' is used
uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
if (on)
^~
drivers/scsi/ufs/ufs-mediatek.c:120:9: note: uninitialized use occurs
here
return ret;
^~~
drivers/scsi/ufs/ufs-mediatek.c:112:3: note: remove the 'if' if its
condition is always true
if (on)
^~~~~~~
drivers/scsi/ufs/ufs-mediatek.c:108:7: warning: variable 'ret' is used
uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
if (!on)
^~~
drivers/scsi/ufs/ufs-mediatek.c:120:9: note: uninitialized use occurs
here
return ret;
^~~
drivers/scsi/ufs/ufs-mediatek.c:108:3: note: remove the 'if' if its
condition is always true
if (!on)
^~~~~~~~
drivers/scsi/ufs/ufs-mediatek.c:96:9: note: initialize the variable
'ret' to silence this warning
int ret;
^
= 0
2 warnings generated.
Remove the default case and initialize ret to -EINVAL to properly fix
this warning.
Fixes: ddd90623ce ("scsi: ufs-mediatek: Add UFS support for Mediatek SoC chips")
Link: https://github.com/ClangBuiltLinux/linux/issues/426
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/ufs/ufs-mediatek.c:19:6: warning: symbol 'ufs_mtk_cfg_unipro_cg' was not declared. Should it be static?
drivers/scsi/ufs/ufs-mediatek.c:55:5: warning: symbol 'ufs_mtk_bind_mphy' was not declared. Should it be static?
drivers/scsi/ufs/ufs-mediatek.c:342:27: warning: symbol 'ufs_mtk_of_match' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Declaring interrupt clear routines as inline is bogus as they are used as
an indirect pointer.
Remove the inline references.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
You can't declare a function inline in a header if it doesn't have a body
available to the compiler. So realistically you either don't declare it
inline or you make it a static inline in the header. I think the latter
applies in this case, so this should be the fix
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We found out that for v2 hw, a SATA disk can not be written to after the
system comes up.
In commit ffb1c820b8 ("scsi: hisi_sas: remove the check of sas_dev status
in hisi_sas_I_T_nexus_reset()"), we introduced a path where we may issue an
internal abort for a SATA device, but without following it with a
softreset.
We need to always follow an internal abort with a software reset, as per HW
programming flow, so add this.
Fixes: ffb1c820b8 ("scsi: hisi_sas: remove the check of sas_dev status in hisi_sas_I_T_nexus_reset()")
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix following sparse warning:
drivers/scsi/mvumi.c:1797:48: warning: Using plain integer as NULL pointer
drivers/scsi/mvumi.c:2143:50: warning: Using plain integer as NULL pointer
drivers/scsi/mvumi.c:755:58: warning: Using plain integer as NULL pointer
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/qedi/qedi_fw.c: In function 'qedi_tmf_resp_work':
drivers/scsi/qedi/qedi_fw.c:158:28: warning:
variable 'cls_sess' set but not used [-Wunused-but-set-variable]
drivers/scsi/qedi/qedi_fw.c: In function 'qedi_tmf_work':
drivers/scsi/qedi/qedi_fw.c:1370:28: warning:
variable 'cls_sess' set but not used [-Wunused-but-set-variable]
It's never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixed a typo for 'iiDMA' cmd in qla_bsg.c.
Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixed a minor formatting issue with comment section in qla_bsg.c
Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a few statements that are not indented correctly, so fix
these. Also add empty line between variable declaration and first
statements in functions. Also remove whitespace between * and mvi_dev to
clean up a cppcheck warning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An if statement is indented correctly and an outb statement has a redundant
empty comment and incorrect indentation. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several lines where the indentation has an extra space, fix this
by removing the spaces.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clean up { brace to fix cppcheck warning. Remove some trailing spaces at
end of a statement. Also clean up an indentation issue.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds UFS support for MediaTek SoC chips.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd_get_pwr_dev_param function and ufs_dev_params struct have been
relocated to ufs core. Switch ufs-hisi to the common interface.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd_get_pwr_dev_param function and ufs_dev_params struct have been
relocated to ufs core. Switch ufs-qcom to the common interface.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd_get_pwr_dev_param defines an interface for power mode management
currently used by both ufs-qcom and ufs-hisi. Move the interface to ufs
core so every driver can take advantage of it.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use HCTX_TYPE_DEFAULT instead of 0 to avoid hardcoding.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use HCTX_TYPE_DEFAULT instead of 0 to avoid hardcoding.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use HCTX_TYPE_DEFAULT instead of 0 to avoid hardcoding.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use HCTX_TYPE_DEFAULT instead of 0 to avoid hardcoding.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
devm_reset_control_get could fail, so the fix checks its return value and
passes the error code upstream in case it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 7f147f9bfd ("scsi: qla2xxx: Fix N2N target discovery with Local
loop") fixed N2N target discovery for local loop. However, same code is
used for FC-AL discovery as well. Added check to make sure we are bypassing
area and domain check only in N2N topology for target discovery.
Fixes: 7f147f9bfd ("scsi: qla2xxx: Fix N2N target discovery with Local loop")
Cc: stable@vger.kernel.org # 5.0+
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several lines of code where the indentation is at an incorrect
level; fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since scsi_device_quiesce() skips SCSI devices that have another state than
RUNNING, OFFLINE or TRANSPORT_OFFLINE, scsi_device_resume() should not
complain about SCSI devices that have been skipped. Hence this patch. This
patch avoids that the following warning appears during resume:
WARNING: CPU: 3 PID: 1039 at blk_clear_pm_only+0x2a/0x30
CPU: 3 PID: 1039 Comm: kworker/u8:49 Not tainted 5.0.0+ #1
Hardware name: LENOVO 4180F42/4180F42, BIOS 83ET75WW (1.45 ) 05/10/2013
Workqueue: events_unbound async_run_entry_fn
RIP: 0010:blk_clear_pm_only+0x2a/0x30
Call Trace:
? scsi_device_resume+0x28/0x50
? scsi_dev_type_resume+0x2b/0x80
? async_run_entry_fn+0x2c/0xd0
? process_one_work+0x1f0/0x3f0
? worker_thread+0x28/0x3c0
? process_one_work+0x3f0/0x3f0
? kthread+0x10c/0x130
? __kthread_create_on_node+0x150/0x150
? ret_from_fork+0x1f/0x30
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Oleksandr Natalenko <oleksandr@natalenko.name>
Cc: Martin Steigerwald <martin@lichtvoll.de>
Cc: <stable@vger.kernel.org>
Reported-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Tested-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Fixes: 3a0a529971 ("block, scsi: Make SCSI quiesce and resume work reliably") # v4.15
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adjust comments accordingly.
Cc: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
cmd->rcu is initialized by scsi_initialize_rq(). For passthrough
requests, blk_get_request() calls scsi_initialize_rq(). For filesystem
requests, scsi_init_command() calls scsi_initialize_rq(). Make sure
that destroy_rcu_head() is called for passthrough requests.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This function is only used inside the SCSI midlayer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.2.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise driver copyright message to show 2019. Update couple of files
modified by 12.2.0.1 patch set.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the 6072 log message string to print the whole 32 bits of the
extended status.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver had duplicated log message numbers making debug difficult.
Make all messages unique.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
