Most of the logic here is try and error since what actually happens does
not match the trm or I miss read it.
My first assumption was that the queue on which the tear-down descriptor
completes (their own complete queue vs "active descriptor" complete
queue) depends on the transfer direction. This seems not to be true
because I manage to trigger
| WARN_ON(c->desc_phys != desc_phys);
and the other few were fine means the tear-down descriptor was valid but
on different queue.
This patch changes the logic here to look on both queues for the
descriptor.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use cppi41_pop_desc() when appropriate instead of open-coding the same
functionality again. That makes the code more readable. The function has
to be moved some lines up for this change.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
With active users over suspend/resume cycles, it turns out that
more registers, in particular DMA_TDFDQ and RXHPCRA0, have to be
restored on resume.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Using the PaRAM configuration function that we split for reuse by the
different DMA types, we implement Cyclic DMA support.
For the cyclic case, we pass different configuration parameters to this
function, and handle all the Cyclic-specific functionality separately.
Callbacks to the DMA users are handled using vchan_cyclic_callback in
the virt-dma layer. Linking is handled the same way as the slave SG case
except for the last slot where we link it back to the first one in a
cyclic fashion.
For continuity, we check for cases where no.of periods is great than the
MAX number of slots the driver can allocate for a particular descriptor
and error out on such cases.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Driver core clears the driver data to NULL after device_release
or on probe failure, so just remove it from here.
Driver core change:
"device-core: Ensure drvdata = NULL when no driver is bound"
(sha1: 0998d06310)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
drivers/dma/imx-dma.c:575:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t'
drivers/dma/imx-dma.c:575:3: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t'
drivers/dma/imx-dma.c:589:4: warning: format '%x' expects argument of type 'unsigned int', but argument 9 has type 'dma_addr_t'
drivers/dma/imx-dma.c:599:4: warning: format '%x' expects argument of type 'unsigned int', but argument 9 has type 'dma_addr_t'
drivers/dma/imx-dma.c:929:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t'
drivers/dma/imx-dma.c:929:2: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t'
drivers/dma/imx-dma.c:959:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t'
drivers/dma/imx-dma.c:959:2: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t'
We can't use the %pa format for these because this relates to phys_addr_t,
and dma_addr_t can be a different size. So, fix these by converting them
to %llx and casting the dma_addr_t to always be unsigned long long.
While we're here, also use %zu for size_t.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
edma header defines DMA_COMPLETE, this causes issues as commit adfedd9a32 move
DMA_SUCCESS to DMA_COMPLETE. edma should properly namespace its defines and
needs a future fix
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
the DMA_SUCCESS is a misnomer as dmaengine indicates the transfer is complete and
gives no guarantee of the transfer success. Hence we should use DMA_COMPLTE
instead of DMA_SUCCESS
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When it fails to allocate a slot, edesc should be free'd before return;
Signed-off-by: Valentin Ilie <valentin.ilie@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
davinci-pcm uses 16 as the no.of periods. With this, in EDMA we have to
allocate atleast 17 slots: 1 slot for channel, and 16 slots the periods.
Due to this, the MAX_NR_SG limitation causes problems, set it to 20 to make
cyclic DMA work when davinci-pcm is converted to use DMA Engine. Also add
a comment clarifying this.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
PaRAM set calculation is abstracted into its own function to
enable better reuse for other DMA cases such as cyclic. We adapt
the Slave SG case to use the new function.
This provides a much cleaner abstraction to the internals of the
PaRAM set. However, any PaRAM attributes that are not common to
all DMA types must be set separately such as setting of interrupts.
This function takes care of the most-common attributes.
Also added comments clarifying A-sync case calculations.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some pl330 have per channel irq and it is necessary
to allocate all of them. Loop over irq assigned for this
device to support these pl330 IPs.
For example this IP is available on Xilinx Zynq platform.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Free memory allocated to edma_desc when failing to allocate slot.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 4981c4dc19 (DMA: shdma: switch DT mode to
use configuration data from a match table) added a new parameter to set_slave()
method but unfortunately got merged later than commit c4f6c41ba7
(dma: add driver for R-Car HPB-DMAC), so that the HPB-DMAC driver retained the
old prototype which caused this warning:
drivers/dma/sh/rcar-hpbdma.c:485: warning: initialization from incompatible
pointer type
The newly added parameter is used to override DMA slave address from 'struct
hpb_dmae_slave_config', so we have to add the 'slave_addr' field to 'struct
hpb_dmae_chan', conditionally assign it in set_slave() method, and return in
slave_addr() method.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit c1c63a14f4 (DMA: shdma: switch to managed
resource allocation) got rid of shdma_free_irq() but unfortunately got merged
later than commit c4f6c41ba7 (dma: add driver for
R-Car HPB-DMAC), so that the HPB-DMAC driver retained the calls and got broken:
drivers/dma/sh/rcar-hpbdma.c: In function `hpb_dmae_alloc_chan_resources':
drivers/dma/sh/rcar-hpbdma.c:435: error: implicit declaration of function
`shdma_free_irq'
Fix this compilation error by removing the remaining shdma_free_irq() calls.
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for suspend/resume functionality to the cppi41
DMA driver. The steps necessary to make the system resume properly were
figured out by trial-and-error. The code as it stands now is the
minimum that has to be done to put the musb host system on an AM33xx
system into an operable state after resume.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dst_addr_width and src_addr_width should be a power of 2. Currently the
driver checks, that they both lie between 1 and 8 and that they are equal
to 1 or even. This however leaves an invalid value of 6 uncaught. Use an
explicit power of 2 check instead.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
[typo fix on changelog]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>