Use the same callback to inject irq/nmi events no matter what irqchip is
in use. Only from VMX for now.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
At the vector level, kernel and userspace irqchip are fairly similar.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Matt T. Yourst notes that kvm_arch_vcpu_ioctl_set_sregs lacks validity
checking for the new cr3 value:
"Userspace callers of KVM_SET_SREGS can pass a bogus value of cr3 to
the kernel. This will trigger a NULL pointer access in gfn_to_rmap()
when userspace next tries to call KVM_RUN on the affected VCPU and kvm
attempts to activate the new non-existent page table root.
This happens since kvm only validates that cr3 points to a valid guest
physical memory page when code *inside* the guest sets cr3. However, kvm
currently trusts the userspace caller (e.g. QEMU) on the host machine to
always supply a valid page table root, rather than properly validating
it along with the rest of the reloaded guest state."
http://sourceforge.net/tracker/?func=detail&atid=893831&aid=2687641&group_id=180599
Check for a valid cr3 address in kvm_arch_vcpu_ioctl_set_sregs, triple
fault in case of failure.
Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
In the new mode instruction is decoded, but not executed. The EIP
is moved to point after the instruction.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
There is no need to skip instruction if the reason for a task switch
is a task gate in IDT and access to it is caused by an external even.
The problem is currently solved only for VMX since there is no reliable
way to skip an instruction in SVM. We should emulate it instead.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
A pte that is shadowed when the guest EFER.NXE=1 is not valid when
EFER.NXE=0; if bit 63 is set, the pte should cause a fault, and since the
shadow EFER always has NX enabled, this won't happen.
Fix by using a different shadow page table for different EFER.NXE bits. This
allows vcpus to run correctly with different values of EFER.NXE, and for
transitions on this bit to be handled correctly without requiring a full
flush.
Signed-off-by: Avi Kivity <avi@redhat.com>
Detect, indicate, and propagate page faults where reserved bits are set.
Take care to handle the different paging modes, each of which has different
sets of reserved bits.
[avi: fix pte reserved bits for efer.nxe=0]
Signed-off-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvm_vcpu_block() unhalts vpu on an interrupt/timer without checking
if interrupt window is actually opened.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently timer events are processed before entering guest mode. Move it
to main vcpu event loop since timer events should be processed even while
vcpu is halted. Timer may cause interrupt/nmi to be injected and only then
vcpu will be unhalted.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We ignore writes to the performance counters and performance event
selector registers already. Kaspersky antivirus reads the eventsel
MSR causing it to crash with the current behaviour.
Return 0 as data when the eventsel registers are read to stop the
crash.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
After discussion with Marcelo, we decided to rework device assignment framework
together. The old problems are kernel logic is unnecessary complex. So Marcelo
suggest to split it into a more elegant way:
1. Split host IRQ assign and guest IRQ assign. And userspace determine the
combination. Also discard msi2intx parameter, userspace can specific
KVM_DEV_IRQ_HOST_MSI | KVM_DEV_IRQ_GUEST_INTX in assigned_irq->flags to
enable MSI to INTx convertion.
2. Split assign IRQ and deassign IRQ. Import two new ioctls:
KVM_ASSIGN_DEV_IRQ and KVM_DEASSIGN_DEV_IRQ.
This patch also fixed the reversed _IOR vs _IOW in definition(by deprecated the
old interface).
[avi: replace homemade bitcount() by hweight_long()]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This issue just appeared in kvm-84 when running on 2.6.28.7 (x86-64)
with PREEMPT enabled.
We're getting syslog warnings like this many (but not all) times qemu
tells KVM to run the VCPU:
BUG: using smp_processor_id() in preemptible [00000000] code:
qemu-system-x86/28938
caller is kvm_arch_vcpu_ioctl_run+0x5d1/0xc70 [kvm]
Pid: 28938, comm: qemu-system-x86 2.6.28.7-mtyrel-64bit
Call Trace:
debug_smp_processor_id+0xf7/0x100
kvm_arch_vcpu_ioctl_run+0x5d1/0xc70 [kvm]
? __wake_up+0x4e/0x70
? wake_futex+0x27/0x40
kvm_vcpu_ioctl+0x2e9/0x5a0 [kvm]
enqueue_hrtimer+0x8a/0x110
_spin_unlock_irqrestore+0x27/0x50
vfs_ioctl+0x31/0xa0
do_vfs_ioctl+0x74/0x480
sys_futex+0xb4/0x140
sys_ioctl+0x99/0xa0
system_call_fastpath+0x16/0x1b
As it turns out, the call trace is messed up due to gcc's inlining, but
I isolated the problem anyway: kvm_write_guest_time() is being used in a
non-thread-safe manner on preemptable kernels.
Basically kvm_write_guest_time()'s body needs to be surrounded by
preempt_disable() and preempt_enable(), since the kernel won't let us
query any per-CPU data (indirectly using smp_processor_id()) without
preemption disabled. The attached patch fixes this issue by disabling
preemption inside kvm_write_guest_time().
[marcelo: surround only __get_cpu_var calls since the warning
is harmless]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The processor is documented to reload the PDPTRs while in PAE mode if any
of the CR4 bits PSE, PGE, or PAE change. Linux relies on this
behaviour when zapping the low mappings of PAE kernels during boot.
The code already handled changes to CR4.PAE; augment it to also notice changes
to PSE and PGE.
This triggered while booting an F11 PAE kernel; the futex initialization code
runs before any CR3 reloads and writes to a NULL pointer; the futex subsystem
ended up uninitialized, killing PI futexes and pulseaudio which uses them.
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
Some processors don't have EFER; don't oops if userspace wants us to
read EFER when we check NX.
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
Properly unregister cpufreq notifier on onload if it was registered
during init.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Not releasing the time_page causes a leak of that page or the compound
page it is situated in.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Impact: Make symbols static.
Fix this sparse warnings:
arch/x86/kvm/mmu.c:992:5: warning: symbol 'mmu_pages_add' was not declared. Should it be static?
arch/x86/kvm/mmu.c:1124:5: warning: symbol 'mmu_pages_next' was not declared. Should it be static?
arch/x86/kvm/mmu.c:1144:6: warning: symbol 'mmu_pages_clear_parents' was not declared. Should it be static?
arch/x86/kvm/x86.c:2037:5: warning: symbol 'kvm_read_guest_virt' was not declared. Should it be static?
arch/x86/kvm/x86.c:2067:5: warning: symbol 'kvm_write_guest_virt' was not declared. Should it be static?
virt/kvm/irq_comm.c:220:5: warning: symbol 'setup_routing_entry' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
IRQ injection status is either -1 (if there was no CPU found
that should except the interrupt because IRQ was masked or
ioapic was misconfigured or ...) or >= 0 in that case the
number indicates to how many CPUs interrupt was injected.
If the value is 0 it means that the interrupt was coalesced
and probably should be reinjected.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvmclock currently falls apart on machines without constant tsc.
This patch fixes it. Changes:
* keep tsc frequency in a per-cpu variable.
* handle kvmclock update using a new request flag, thus checking
whenever we need an update each time we enter guest context.
* use a cpufreq notifier to track frequency changes and force
kvmclock updates.
* send ipis to kick cpu out of guest context if needed to make
sure the guest doesn't see stale values.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
AMD K10 CPUs implement the FFXSR feature that gets enabled using
EFER. Let's check if the virtual CPU description includes that
CPUID feature bit and allow enabling it then.
This is required for Windows Server 2008 in Hyper-V mode.
v2 adds CPUID capability exposure
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently KVM has a static routing from GSI numbers to interrupts (namely,
0-15 are mapped 1:1 to both PIC and IOAPIC, and 16:23 are mapped 1:1 to
the IOAPIC). This is insufficient for several reasons:
- HPET requires non 1:1 mapping for the timer interrupt
- MSIs need a new method to assign interrupt numbers and dispatch them
- ACPI APIC mode needs to be able to reassign the PCI LINK interrupts to the
ioapics
This patch implements an interrupt routing table (as a linked list, but this
can be easily changed) and a userspace interface to replace the table. The
routing table is initialized according to the current hardwired mapping.
Signed-off-by: Avi Kivity <avi@redhat.com>
Some typos, comments, whitespace errors corrected in the cpuid code
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Certain clocks (such as TSC) in older 2.6 guests overaccount for lost
ticks, causing severe time drift. Interrupt reinjection magnifies the
problem.
Provide an option to disable it.
[avi: allow room for expansion in case we want to disable reinjection
of other timers]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Since we advertise MSR_VM_HSAVE_PA, userspace will attempt to read it
even on Intel. Implement fake support for this MSR to avoid the
warnings.
Signed-off-by: Avi Kivity <avi@redhat.com>
vmap() on guest pages hides those pages from the Linux mm for an extended
(userspace determined) amount of time. Get rid of it.
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This commit change the name of emulator_read_std into kvm_read_guest_virt,
and add new function name kvm_write_guest_virt that allow writing into a
guest virtual address.
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
VMX initializes the TSC offset for each vcpu at different times, and
also reinitializes it for vcpus other than 0 on APIC SIPI message.
This bug causes the TSC's to appear unsynchronized in the guest, even if
the host is good.
Older Linux kernels don't handle the situation very well, so
gettimeofday is likely to go backwards in time:
http://www.mail-archive.com/kvm@vger.kernel.org/msg02955.htmlhttp://sourceforge.net/tracker/index.php?func=detail&aid=2025534&group_id=180599&atid=893831
Fix it by initializating the offset of each vcpu relative to vm creation
time, and moving it from vmx_vcpu_reset to vmx_vcpu_setup, out of the
APIC MP init path.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Don't allow a vcpu with cr4.pge cleared to use a shadow page created with
cr4.pge set; this might cause a cr3 switch not to sync ptes that have the
global bit set (the global bit has no effect if !cr4.pge).
This can only occur on smp with different cr4.pge settings for different
vcpus (since a cr4 change will resync the shadow ptes), but there's no
cost to being correct here.
Signed-off-by: Avi Kivity <avi@redhat.com>
Add the remaining bits to make use of debug registers also for guest
debugging, thus enabling the use of hardware breakpoints and
watchpoints.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
So far KVM only had basic x86 debug register support, once introduced to
realize guest debugging that way. The guest itself was not able to use
those registers.
This patch now adds (almost) full support for guest self-debugging via
hardware registers. It refactors the code, moving generic parts out of
SVM (VMX was already cleaned up by the KVM_SET_GUEST_DEBUG patches), and
it ensures that the registers are properly switched between host and
guest.
This patch also prepares debug register usage by the host. The latter
will (once wired-up by the following patch) allow for hardware
breakpoints/watchpoints in guest code. If this is enabled, the guest
will only see faked debug registers without functionality, but with
content reflecting the guest's modifications.
Tested on Intel only, but SVM /should/ work as well, but who knows...
Known limitations: Trapping on tss switch won't work - most probably on
Intel.
Credits also go to Joerg Roedel - I used his once posted debugging
series as platform for this patch.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This rips out the support for KVM_DEBUG_GUEST and introduces a new IOCTL
instead: KVM_SET_GUEST_DEBUG. The IOCTL payload consists of a generic
part, controlling the "main switch" and the single-step feature. The
arch specific part adds an x86 interface for intercepting both types of
debug exceptions separately and re-injecting them when the host was not
interested. Moveover, the foundation for guest debugging via debug
registers is layed.
To signal breakpoint events properly back to userland, an arch-specific
data block is now returned along KVM_EXIT_DEBUG. For x86, the arch block
contains the PC, the debug exception, and relevant debug registers to
tell debug events properly apart.
The availability of this new interface is signaled by
KVM_CAP_SET_GUEST_DEBUG. Empty stubs for not yet supported archs are
provided.
Note that both SVM and VTX are supported, but only the latter was tested
yet. Based on the experience with all those VTX corner case, I would be
fairly surprised if SVM will work out of the box.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Userspace has to tell the kernel module somehow that nested SVM should be used.
The easiest way that doesn't break anything I could think of is to implement
if (cpuid & svm)
allow write to efer
else
deny write to efer
Old userspaces mask the SVM capability bit, so they don't break.
In order to find out that the SVM capability is set, I had to split the
kvm_emulate_cpuid into a finding and an emulating part.
(introduced in v6)
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Implement the hsave MSR, that gives the VCPU a GPA to save the
old guest state in.
v2 allows userspace to save/restore hsave
v4 dummys out the hsave MSR, so we use a host page
v6 remembers the guest's hsave and exports the MSR
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This is better.
Currently, this code path is posing us big troubles,
and we won't have a decent patch in time. So, temporarily
disable it.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
In the past, kvm_get_kvm() and kvm_put_kvm() was called in assigned device irq
handler and interrupt_work, in order to prevent cancel_work_sync() in
kvm_free_assigned_irq got a illegal state when waiting for interrupt_work done.
But it's tricky and still got two problems:
1. A bug ignored two conditions that cancel_work_sync() would return true result
in a additional kvm_put_kvm().
2. If interrupt type is MSI, we would got a window between cancel_work_sync()
and free_irq(), which interrupt would be injected again...
This patch discard the reference count used for irq handler and interrupt_work,
and ensure the legal state by moving the free function at the very beginning of
kvm_destroy_vm(). And the patch fix the second bug by disable irq before
cancel_work_sync(), which may result in nested disable of irq but OK for we are
going to free it.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvm_arch_sync_events is introduced to quiet down all other events may happen
contemporary with VM destroy process, like IRQ handler and work struct for
assigned device.
For kvm_arch_sync_events is called at the very beginning of kvm_destroy_vm(), so
the state of KVM here is legal and can provide a environment to quiet down other
events.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
There is no point in doing the ready_for_nmi_injection/
request_nmi_window dance with user space. First, we don't do this for
in-kernel irqchip anyway, while the code path is the same as for user
space irqchip mode. And second, there is nothing to loose if a pending
NMI is overwritten by another one (in contrast to IRQs where we have to
save the number). Actually, there is even the risk of raising spurious
NMIs this way because the reason for the held-back NMI might already be
handled while processing the first one.
Therefore this patch creates a simplified user space NMI injection
interface, exporting it under KVM_CAP_USER_NMI and dropping the old
KVM_CAP_NMI capability. And this time we also take care to provide the
interface only on archs supporting NMIs via KVM (right now only x86).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If the guest executes invlpg, peek into the pagetable and attempt to
prepopulate the shadow entry.
Also stop dirty fault updates from interfering with the fork detector.
2% improvement on RHEL3/AIM7.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Skip syncing global pages on cr3 switch (but not on cr4/cr0). This is
important for Linux 32-bit guests with PAE, where the kmap page is
marked as global.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The code to traverse the cpuid data array list for counting type of leaves is
currently broken.
This patches fixes the 2 things in it.
1. Set the 1st counting entry's flag KVM_CPUID_FLAG_STATE_READ_NEXT. Without
it the code will never find a valid entry.
2. Also the stop condition in the for loop while looking for the next unflaged
entry is broken. It needs to stop when it find one matching entry;
and in the case of count of 1, it will be the same entry found in this
iteration.
Signed-Off-By: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
