As per the usual standard with hwmon drivers the mapping to sysfs
entries follows the register map of the device e.g. in0_input
corresponds to the register 0x20, in1_input corresponds to 0x21 etc.
Hardware designers tend to work with input pins instead of registers
which is where things start to get confusing. A hardware designer might
say "the 1.5V rail is connected to the VCCP pin" leaving the software
designer none the wiser as to which of the sysfs entries should be
associated with the label "1.5V".
Try to bridge the gap by documenting the mapping of sysfs entries to
the corresponding pins. This should allow someone to create a
configuration file or other mapping without needing to dive into the
code and ADT datasheets.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When enabled temperature smoothing allows ramping the fan speed over a
configurable period of time instead of jumping to the new speed
instantaneously.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
By default adt7475 will stop the fans (pwm duty cycle 0%) when the
temperature drops past Tmin - hysteresis. Some systems want to keep the
fans moving even when the temperature drops so add new sysfs attributes
that configure the enhanced acoustics min 1-3 which allows the fans to
run at the minimum configure pwm duty cycle.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADT7476 has 5 dedicated pins for VID input, and the +12V input can
optionally be used as a 6th VID pin. Add support for VID input.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the Analog Devices ADT7476 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 5 voltage inputs instead of 2, and VID input
pins.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the Analog Devices ADT7490 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 6 voltage inputs instead of 2.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
New documentation for the adt7475 driver, based on the adt7473 driver
documentation. It is IMHO much more useful that the previous
documentation which was essentially redundant with sysfs-interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Hwmon driver for the ADT7475 chip.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
