[ Upstream commit f57011e72f ]
Setting the vmmc supplies is crucial since otherwise the supplying
regulators get disabled and the SD interfaces are no longer powered
which leads to system failures if the system is booted from that SD
interface.
Fixes: 1e44d3f880 ("ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module")
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a26c56ae67 upstream.
Use the `marvell,reg-init` DT property to configure the LED[2]/INTn pin
of the Marvell 88E1514 ethernet PHY on Turris Omnia into interrupt mode.
Without this the pin is by default in LED[2] mode, and the Marvell PHY
driver configures LED[2] into "On - Link, Blink - Activity" mode.
This fixes the issue where the pca9538 GPIO/interrupt controller (which
can't mask interrupts in HW) received too many interrupts and after a
time started ignoring the interrupt with error message:
IRQ 71: nobody cared
There is a work in progress to have the Marvell PHY driver support
parsing PHY LED nodes from OF and registering the LEDs as Linux LED
class devices. Once this is done the PHY driver can also automatically
set the pin into INTn mode if it does not find LED[2] in OF.
Until then, though, we fix this via `marvell,reg-init` DT property.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Fixes: 26ca8b52d6 ("ARM: dts: add support for Turris Omnia")
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: <stable@vger.kernel.org>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9bbce32a20 ]
Without DT aliases, the numbering of mmc interfaces is unpredictable.
Adding them makes it possible to refer to devices consistently. The
popular suggestion to use UUIDs obviously doesn't work with a blank
device fresh from the factory.
See commit fa2d0aa969 ("mmc: core: Allow setting slot index via
device tree alias") for more discussion.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4817a1b6b ]
For NAND Ecc layout, there is a dependency from old kernel's nand driver
setting and current. if old kernel use 4 bit ecc , we should use 4 bit
in new kernel either. else will run into following error at filesystem
mounting.
So, enable fsl,use-minimum-ecc from device tree, to fix this mismatch
[ 9.449265] ubi0: scanning is finished
[ 9.463968] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read only 22528 bytes, retry
[ 9.486940] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read only 22528 bytes, retry
[ 9.509906] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read only 22528 bytes, retry
[ 9.532845] ubi0 error: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read 22528 bytes
Fixes: f9ecf10cb8 ("ARM: dts: imx6ull: add MYiR MYS-6ULX SBC")
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 221c3a09dd upstream.
Fix the phy address to 7 for Ethernet PHY on SAMA5D27 SOM1. No
connection established if phy address 0 is used.
The board uses the 24 pins version of the KSZ8081RNA part, KSZ8081RNA
pin 16 REFCLK as PHYAD bit [2] has weak internal pull-down. But at
reset, connected to PD09 of the MPU it's connected with an internal
pull-up forming PHYAD[2:0] = 7.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Fixes: 2f61929eb1 ("ARM: dts: at91: at91-sama5d27_som1: fix PHY ID")
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c69c8a173 upstream.
Fix the whole mux-mask table according to datasheet for the sam9x60
product. Too much functions for pins were disabled leading to
misunderstandings when enabling more peripherals or taking this table
as an example for another board.
Take advantage of this fix to move the mux-mask in the SoC file where it
belongs and use lower case letters for hex numbers like everywhere in
the file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 1e5f532c27 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Cc: <stable@vger.kernel.org> # 5.6+
Cc: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210310152006.15018-1-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 664979bba8 upstream.
According to the datasheet PA7 can be set to either function A, B or
C (see table 6-2 of DS60001579D). The previous value would permit just
configuring with function C.
Signed-off-by: Federico Pellegrin <fede@evolware.org>
Fixes: 1e5f532c27 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Cc: <stable@vger.kernel.org> # 5.6+
Cc: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67e3f828bd upstream.
The ARM 'adrl' pseudo instruction is a bit problematic, as it does not
exist in Thumb mode, and it is not implemented by Clang either. Since
the Thumb variant has a slightly bigger range, it is sometimes necessary
to emit the 'adrl' variant in ARM mode where Thumb mode can use adr just
fine. However, that still leaves the Clang issue, which does not appear
to be supporting this any time soon.
So let's switch to the adr_l macro, which works for both ARM and Thumb,
and has unlimited range.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2acb909750 ]
It was observed that decompressor running on hardware implementing ARM v8.2
Load/Store Multiple Atomicity and Ordering Control (LSMAOC), say, as guest,
would stuck just after:
Uncompressing Linux... done, booting the kernel.
The reason is that it clears nTLSMD bit when disabling caches:
nTLSMD, bit [3]
When ARMv8.2-LSMAOC is implemented:
No Trap Load Multiple and Store Multiple to
Device-nGRE/Device-nGnRE/Device-nGnRnE memory.
0b0 All memory accesses by A32 and T32 Load Multiple and Store
Multiple at EL1 or EL0 that are marked at stage 1 as
Device-nGRE/Device-nGnRE/Device-nGnRnE memory are trapped and
generate a stage 1 Alignment fault.
0b1 All memory accesses by A32 and T32 Load Multiple and Store
Multiple at EL1 or EL0 that are marked at stage 1 as
Device-nGRE/Device-nGnRE/Device-nGnRnE memory are not trapped.
This bit is permitted to be cached in a TLB.
This field resets to 1.
Otherwise:
Reserved, RES1
So as effect we start getting traps we are not quite ready for.
Looking into history it seems that mask used for SCTLR clear came from
the similar code for ARMv4, where bit[3] is the enable/disable bit for
the write buffer. That not applicable to ARMv7 and onwards, so retire
that bit from the masks.
Fixes: 7d09e85448 ("[ARM] 4393/2: ARMv7: Add uncompressing code for the new CPU Id format")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46ecdfc183 ]
Split up the pins for each fan. This is needed in order to control them
Fixes: ced8025b56 ("ARM: dts: armada388-helios4")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44f416879a ]
We have gpio_86 wired internally to the bandgap thermal shutdown
interrupt on 4430 like we have it on 4460 according to the TRM.
This can be found easily by searching for TSHUT.
For some reason the thermal shutdown interrupt was never added
for 4430, let's add it. I believe this is needed for the thermal
shutdown interrupt handler ti_bandgap_tshut_irq_handler() to call
orderly_poweroff().
Fixes: aa9bb4bb88 ("arm: dts: add omap4430 thermal data")
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e7d9a583a ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: aac4e06153 ("ARM: dts: odroidxu3: Enable wake alarm of S2MPS11 RTC")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-6-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ac8893c4f ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Fixes: 1fed225271 ("ARM: dts: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-5-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77e6a5467c ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 53dd4138bb ("ARM: dts: Add exynos5250-spring device tree")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-4-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 437ae60947 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: faaf348ef4 ("ARM: dts: Add board dts file for exynos3250-rinato")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-3-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8528cda2b7 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: e0cefb3f79 ("ARM: dts: add board dts file for Exynos3250-based Monk board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-2-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb31334687 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: b004a34bd0 ("ARM: dts: exynos: Add exynos3250-artik5 dtsi file for ARTIK5 module")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-1-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5638159f6d ]
This reverts commit c17e9377aa.
The lpc32xx clock driver is not able to actually change the PLL rate as
this would require reparenting ARM_CLK, DDRAM_CLK, PERIPH_CLK to SYSCLK,
then stop the PLL, update the register, restart the PLL and wait for the
PLL to lock and finally reparent ARM_CLK, DDRAM_CLK, PERIPH_CLK to HCLK
PLL.
Currently, the HCLK driver simply updates the registers but this has no
real effect and all the clock rate calculation end up being wrong. This is
especially annoying for the peripheral (e.g. UARTs, I2C, SPI).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20210203090320.GA3760268@piout.net'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 181739822c upstream.
With the arrival of
commit 2fee958319 ("spi: dt-bindings: clarify CS behavior for spi-cs-high and gpio descriptors")
it was clarified what the proper state for cs-gpios should be, even if the
flag is ignored. The driver code is doing the right thing since
766c6b63aa ("spi: fix client driver breakages when using GPIO descriptors")
The chip-select of the td028ttec1 panel is active-low, so we must omit spi-cs-high;
attribute (already removed by separate patch) and should now use GPIO_ACTIVE_LOW for
the client device description to be fully consistent.
Fixes: 766c6b63aa ("spi: fix client driver breakages when using GPIO descriptors")
CC: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07af7810e0 upstream.
This reverts
commit f1f028ff89 ("DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again")
which had to be intruduced after
commit 6953c57ab1 ("gpio: of: Handle SPI chipselect legacy bindings")
broke the GTA04 display. This contradicted the data sheet but was the only
way to get it as an spi client operational again.
The panel data sheet defines the chip-select to be active low.
Now, with the arrival of
commit 766c6b63aa ("spi: fix client driver breakages when using GPIO descriptors")
the logic of interaction between spi-cs-high and the gpio descriptor flags
has been changed a second time, making the display broken again. So we have
to remove the original fix which in retrospect was a workaround of a bug in
the spi subsystem and not a feature of the panel or bug in the device tree.
With this fix the device tree is back in sync with the data sheet and
spi subsystem code.
Fixes: 766c6b63aa ("spi: fix client driver breakages when using GPIO descriptors")
CC: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a900cac375 ]
BPi Pro needs TX and RX delay for Gbit to work reliable and avoid high
packet loss rates. The realtek phy driver overrides the settings of the
pull ups for the delays, so fix this for BananaPro.
Fix the phy-mode description to correctly reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 10662a33dc ("ARM: dts: sun7i: Add dts file for Bananapro board")
Signed-off-by: Hermann Lauer <Hermann.Lauer@uni-heidelberg.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210128111842.GA11919@lemon.iwr.uni-heidelberg.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83d4112240 ]
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Since GPIO_ACTIVE_HIGH is defined as 0, this change only increases the
correctness of the DT.
Fixes: fde180f06d ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 087698939f ]
The DRC02 has no use for the on-SoM touchscreen controller, and the
on-SoM touchscreen controller may not even be populated, which then
results in error messages in kernel log. Disable the touchscreen
controller in DT.
Fixes: fde180f06d ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a9b001237 ]
The DHCOM SoM uSD slot card detect signal is connected to GPIO PG1,
describe it in the DT.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0572c0734 ]
The uSD card detect signal on the DH DRC02 is active-high, with
a default pull down resistor on the board. Invert the polarity.
Fixes: fde180f06d ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
--
Note that this could not be tested on prototype SoMs, now that it is
tested, this issue surfaced, so it needs to be fixed.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cc0bfc9c1 ]
The PHY address bit 2 is configured by the LED pin. Attaching a LED
to this pin is not sufficient to guarantee this configuration pin is
correctly read. This leads to some platforms having their PHY at
address 0 and others at address 4.
If there is no phy-handle specified, the FEC driver will scan the PHY
bus for a PHY and use that. Consequently, adding the DT configuration
of the PHY and the phy properties to the FEC driver broke some boards.
Fix this by removing the phy-handle property, and listing two PHY
entries for both possible PHY addresses, so that the DT configuration
for the PHY can be found by the PHY driver.
Fixes: 86b08bd5b9 ("ARM: dts: imx6-sr-som: add ethernet PHY configuration")
Reported-by: Christoph Mattheis <christoph.mattheis@arcor.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 30596ae054 upstream.
Commit 7536c7e03e ("of/fdt: Remove redundant kbasename function
call") exposed a bug creating DT nodes in the ATAGS to DT fixup code.
Non-existent nodes would mistaken get created with a leading '/'. The
problem was fdt_path_offset() takes a full path while creating a node
with fdt_add_subnode() takes just the basename.
Since this we only add root child nodes, we can just skip over the '/'.
Fixes: 7536c7e03e ("of/fdt: Remove redundant kbasename function call")
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Qi Zheng <arch0.zheng@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210126023905.1631161-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6337c2353a upstream.
The pwms property have to specify the no-/inverted flag since
commit fa28d8212e ("ARM: dts: imx: default to #pwm-cells = <3>
in the SoC dtsi files").
Fixes: fa28d8212e ("ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a996b2d8a upstream.
The Ux500 platforms have some memory carveouts set aside for
communicating with the modem and for the initial secure software
(ISSW). These areas are protected by the memory controller
and will result in an external abort if accessed like common
read/write memory.
On the legacy boot loaders, these were set aside by using
cmdline arguments such as this:
mem=96M@0 mem_mtrace=15M@96M mem_mshared=1M@111M
mem_modem=16M@112M mali.mali_mem=32M@128M mem=96M@160M
hwmem=127M@256M mem_issw=1M@383M mem_ram_console=1M@384M
mem=638M@385M
Reserve the relevant areas in the device tree instead. The
"mali", "hwmem", "mem_ram_console" and the trailing 1MB at the
end of the memory reservations in the list are not relevant for
the upstream kernel as these are nowadays replaced with
upstream technologies such as CMA. The modem and ISSW
reservations are necessary.
This was manifested in a bug that surfaced in response to
commit 7fef431be9 ("mm/page_alloc: place pages to tail in __free_pages_core()")
which changes the behaviour of memory allocations
in such a way that the platform will sooner run into these
dangerous areas, with "Unhandled fault: imprecise external
abort (0xc06) at 0xb6fd83dc" or similar: the real reason
turns out to be that the PTE is pointing right into one of
the reserved memory areas. We were just lucky until now.
We need to augment the DB8500 and DB8520 SoCs similarly
and also create a new include for the DB9500 used in the
Snowball since this does not have a modem and thus does
not need the modem memory reservation, albeit it needs
the ISSW reservation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Cc: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20201213225517.3838501-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd25c88366 upstream.
to be consistent with kernel versions up to v5.9 (mmc aliases not used here).
usdhc1 is not wired up on this board and therefore cannot be used.
Start mmc aliases with usdhc2.
Signed-off-by: Soeren Moch <smoch@web.de>
Cc: stable@vger.kernel.org # 5.10.x
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bac7171719 ]
dtc points out that the interrupts for some devices are not parsable:
picoxcell-pc3x2.dtsi:45.19-49.5: Warning (interrupts_property): /paxi/gem@30000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:51.21-55.5: Warning (interrupts_property): /paxi/dmac@40000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:57.21-61.5: Warning (interrupts_property): /paxi/dmac@50000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:233.21-237.5: Warning (interrupts_property): /rwid-axi/axi2pico@c0000000: Missing interrupt-parent
There are two VIC instances, so it's not clear which one needs to be
used. I found the BSP sources that reference VIC0, so use that:
https://github.com/r1mikey/meta-picoxcell/blob/master/recipes-kernel/linux/linux-picochip-3.0/0001-picoxcell-support-for-Picochip-picoXcell-SoC.patch
Acked-by: Jamie Iles <jamie@jamieiles.com>
Link: https://lore.kernel.org/r/20201230152010.3914962-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7887cc89d5 ]
A too high brightness by default (default is max) makes the
screen go blank. Set this to 15 as in the Vendor tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20201214223413.253893-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f1dc15cd7f upstream.
AES needs to be disabled on Nokia N950/N9 as well (HS devices), otherwise
kernel fails to boot.
Fixes: c312f06631 ("ARM: dts: omap3: Migrate AES from hwmods to sysc-omap2")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd7cd7e05a upstream.
Commit 9ce2746304 ("cpufreq: tegra20: Use generic cpufreq-dt driver
(Tegra30 supported now)") update the Tegra20 CPUFREQ driver to use the
generic CPUFREQ device-tree driver. Since this change CPUFREQ support
on the Tegra20 Ventana platform has been broken because the necessary
device-tree nodes with the operating point information are not populated
for this platform. Fix this by updating device-tree for Venata to
include the operating point informration for Tegra20.
Fixes: 9ce2746304 ("cpufreq: tegra20: Use generic cpufreq-dt driver (Tegra30 supported now)")
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85b8350ae9 upstream.
CAN0 and CAN1 instances share the same message ram configured
at 0x210000 on sama5d2 Linux systems.
According to current configuration of CAN0, we need 0x1c00 bytes
so that the CAN1 don't overlap its message ram:
64 x RX FIFO0 elements => 64 x 72 bytes
32 x TXE (TX Event FIFO) elements => 32 x 8 bytes
32 x TXB (TX Buffer) elements => 32 x 72 bytes
So a total of 7168 bytes (0x1C00).
Fix offset to match this needed size.
Make the CAN0 message ram ioremap match exactly this size so that is
easily understandable. Adapt CAN1 size accordingly.
Fixes: bc6d5d7666 ("ARM: dts: at91: sama5d2: add m_can nodes")
Reported-by: Dan Sneddon <dan.sneddon@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Cc: stable@vger.kernel.org # v4.13+
Link: https://lore.kernel.org/r/20201203091949.9015-1-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ecec38547 ]
The dbgadtb macro is passed the size of the appended DTB, not the end
address.
Fixes: c03e41470e ("ARM: 9010/1: uncompress: Print the location of appended DTB")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 656ab1bdcd ]
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. On similar boards with the same PHY this fixes an issue where
Ethernet link would not come up when using ip link set down/up.
Fixes: a2c6e82e53 ("ARM: dts: meson: switch to the generic Ethernet PHY reset bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # on Odroid-C1+
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/ff78772b306411e145769c46d4090554344db41e.1607363522.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b5dcc8d42 ]
Due to strobe signal not being propagated from CPU to securam
the securam needs to be mapped as device or strongly ordered memory
to work properly. Otherwise, updating to one offset may affect
the adjacent locations in securam.
Fixes: d4ce5f44d4 ("ARM: dts: at91: sama5d2: Add securam node")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/1606903025-14197-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab8a9bb41b ]
atmel,osc-bypass property sets the bit 1 at main oscillator register.
On SAM9X60 this bit is not valid according to datasheet (chapter
28.16.9 PMC Clock Generator Main Oscillator Register).
Fixes: 1e5f532c27 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Marco Cardellini <marco.cardellini@microchip.com>
Link: https://lore.kernel.org/r/1606903025-14197-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f24479ead ]
The switches with integrated CPUs have only got a single i2c controller.
They incorrectly gained one when they were split from the Armada-XP.
Fixes: 43e28ba877 ("ARM: dts: Use armada-370-xp as a base for armada-xp-98dx3236")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1062fa729 ]
The pincontrol node is needed for USB Host since Linux v5.7-rc1. Without
it the driver probes but VBus is not powered because of wrong pincontrol
configuration.
Fixes: b7c2b61570 ("ARM: at91: add Atmel's SAMA5D3 Xplained board")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201118120019.1257580-4-cristian.birsan@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be4dd2d448 ]
The pincontrol node is needed for USB Host since Linux v5.7-rc1. Without
it the driver probes but VBus is not powered because of wrong pincontrol
configuration.
Fixes: 38153a0178 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201118120019.1257580-3-cristian.birsan@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ba6291086 ]
The pincontrol node is needed for USB Host since Linux v5.7-rc1. Without
it the driver probes but VBus is not powered because of wrong pincontrol
configuration.
Fixes: 1e5f532c27 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201118120019.1257580-2-cristian.birsan@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
