[ Upstream commit 10201396ef ]
Disable IBI IRQ signal and status only when hot-join and SIR enabling of
all target devices attached to the bus are disabled.
Fixes: e389b1d72a ("i3c: dw: Add support for in-band interrupts")
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Link: https://lore.kernel.org/r/20240119054547.983693-1-dylan_hung@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
As per the Cadence IP document fixed the I2C clock divider value limit from
16 bits instead of 10 bits. Without this change setting up the I2C clock to
low frequencies will not work as the prescaler value might be greater than
10 bit number.
I3C clock divider value is 10 bits only. Updating the macro names for both.
Signed-off-by: Harshit Shah <harshitshah.opendev@gmail.com>
Link: https://lore.kernel.org/r/1703927483-28682-1-git-send-email-harshitshah.opendev@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I3C allow devices early terminate data transfer. So set "actual_len" to
indicate how much data get by i3c_priv_xfer.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231201222532.2431484-6-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I3C transfer (SDR), target can early terminate read transfer.
I3C transfer (HDR), target can end write transfer.
I2C transfer, target can NACK write transfer.
'actual_len' is better name than 'read_len'.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231201222532.2431484-5-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add hot join support for svc master controller. Disable hot join by
default.
User can use sysfs entry to enable hot join.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231201222532.2431484-3-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add hotjoin entry in sys file system allow user enable/disable hotjoin
feature.
Add (*enable(disable)_hotjoin)() to i3c_master_controller_ops.
Add api i3c_master_enable(disable)_hotjoin();
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231201222532.2431484-2-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Some I3C hardware will report error when an incorrect length is received from
device. GETMXDS CCC are available in 2 formats: without turnaround time (format
1) and with turnaround time (format 2). There is no mechanics to determine which
format is supported by device. So in case sending GETMXDS CCC format 2 resulted
in a failure, try sending GETMXDS CCC format 1 instead.
Signed-off-by: Joshua Yeong <joshua.yeong@starfivetech.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231114085525.6271-2-joshua.yeong@starfivetech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Implement a local bounce buffer for private I3C SDR and I2C transfers
when using DMA and the buffer attached to the transfer is not DMA safe.
Otherwise the DMA transfer will fail and with following warning:
[ 11.411059] i3c mipi-i3c-hci.0: rejecting DMA map of vmalloc memory
[ 11.417313] WARNING: CPU: 3 PID: 357 at include/linux/dma-mapping.h:332 hci_dma_queue_xfer+0x2e2/0x300 [mipi_i3c_hci]
Strictly speaking private I3C SDR transfers are expected to pass a
DMA-able buffer. However I fear this requirement may easily be slipped
or go unnoticed when I3C interface support is added into a existing
device driver that use regmap API to read/write stack variables.
For example this is the case with the commit 2660b0080b ("iio: imu:
st_lsm6dsx: add i3c basic support for LSM6DSO and LSM6DSR").
Buffer of an I2C message is not required to be DMA safe and the I2C core
provides i2c_(get|put)_dma_safe_msg_buf() helpers for the host
controllers that do DMA and that is also recommendation for the
i2c_xfers() callback from the I3C core.
However due to above I3C private transfers reason I decided to implement
a bounce buffer for them and reuse the same code for the I2C transfers
too. Since this driver is currently the only I3C host controller driver
that can do DMA the implementation is done here and not in I3C core.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20231109133708.653950-5-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Handle also I3C address header error response status as the end of DAA
process in hci_cmd_v1_daa().
According to MIPI I3C HCI Specification v1.1 the NACK error during DAA
process comes when the device does not accept the dynamic address.
Currently code uses it for successful exit from the process and fails
with any other error response.
I'm unsure is this MIPI I3C HCI version specific difference or
specification misunderstanding but on an early MIPI I3C HCI version
compatible controller responds always with I3C address header error and
not with NACK error when there is no device on the bus or no more devices
participating to DAA process.
Handle now both response statuses as the end of DAA.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20231109133708.653950-4-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Function hci_cmd_v1_daa() uses only single transfer at a time so no need
to allocate two transfers and access can be simplified.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20231109133708.653950-3-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Currently probe of mipi-i3c-hci will fail if bus doesn't have any I3C
devices connected. This happens when CCC commands that are sent during
i3c_master_bus_init() are not ACKed by any device and controller responds
with an error status set.
The controller can detect NACK both during I3C address header
transmission (broadcast address 0x7e is not ACKed) and when target
device address or dynamic address assignment is NACKed. Former as error
status 0x4: Address Header Error and latter as 0x5: NACK.
Difference between those two NACK statuses were not described explicitly
until MIPI I3C HCI Specification v1.1. Earlier versions share the same
error status code though.
Report both of those as I3C_ERROR_M2 to I3C core code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20231109133708.653950-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Core:
- handle IBI in the proper order
Drivers:
- cdns: fix status register access
- mipi-i3c-hci: many fixes now that the driver has been actually tested
- svc: many IBI fixes, correct compatible string, fix hot join corner cases
-----BEGIN PGP SIGNATURE-----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=rFcf
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"There are now more fixes because as stated in my previous pull
request, people now have access to actual hardware.
Core:
- handle IBI in the proper order
Drivers:
- cdns: fix status register access
- mipi-i3c-hci: many fixes now that the driver has been actually
tested
- svc: many IBI fixes, correct compatible string, fix hot join corner
cases"
* tag 'i3c/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux: (29 commits)
i3c: master: handle IBIs in order they came
i3c: master: mipi-i3c-hci: Fix a kernel panic for accessing DAT_data.
i3c: master: svc: fix compatibility string mismatch with binding doc
i3c: master: svc: fix random hot join failure since timeout error
i3c: master: svc: fix SDA keep low when polling IBIWON timeout happen
i3c: master: svc: fix check wrong status register in irq handler
i3c: master: svc: fix ibi may not return mandatory data byte
i3c: master: svc: fix wrong data return when IBI happen during start frame
i3c: master: svc: fix race condition in ibi work thread
i3c: Fix typo "Provisional ID" to "Provisioned ID"
i3c: Fix potential refcount leak in i3c_master_register_new_i3c_devs
i3c: mipi-i3c-hci: Resume controller after aborted transfer
i3c: mipi-i3c-hci: Resume controller explicitly
i3c: mipi-i3c-hci: Fix missing xfer->completion in hci_cmd_v1_daa()
i3c: mipi-i3c-hci: Do not unmap region not mapped for transfer
i3c: mipi-i3c-hci: Set number of SW enabled Ring Bundles earlier
i3c: mipi-i3c-hci: Fix race between bus cleanup and interrupt
i3c: mipi-i3c-hci: Set ring start request together with enable
i3c: mipi-i3c-hci: Remove BUG() when Ring Abort request times out
i3c: mipi-i3c-hci: Fix out of bounds access in hci_dma_irq_handler
...
IBI shall be handled in order they appear on the bus. Otherwise could hit
case when order of handling them in device driver will be different. It may
lead to invalid assembling fragmented packets or events order broken.
Added separate workqueue with option WQ_MEM_RECLAIM for each device driver.
This ensures IBI handling order and improves IBI handling performance: IBI
handlers for device B are not blocked by IBI handlers for device A.
Original solution (single workqueue in main driver) was able to handle also
general IBI (not related to specific device) like HJ or MR. So leaving this
for such purposes.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/20231015222334.1652401-2-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The `i3c_master_bus_init` function may attach the I2C devices before the
I3C bus initialization. In this flow, the DAT `alloc_entry`` will be used
before the DAT `init`. Additionally, if the `i3c_master_bus_init` fails,
the DAT `cleanup` will execute before the device is detached, which will
execue DAT `free_entry` function. The above scenario can cause the driver
to use DAT_data when it is NULL.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20231023080237.560936-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In the binding documentation, the compatible string is specified as
'silvaco,i3c-master-v1', but in the driver, it is defined as
'silvaco,i3c-master'.
Rename 'silvaco,i3c-master' to 'silvaco,i3c-master-v1' to ensure
compatibility with the documentation.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231017194657.3199749-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
master side report:
silvaco-i3c-master 44330000.i3c-master: Error condition: MSTATUS 0x020090c7, MERRWARN 0x00100000
BIT 20: TIMEOUT error
The module has stalled too long in a frame. This happens when:
- The TX FIFO or RX FIFO is not handled and the bus is stuck in the
middle of a message,
- No STOP was issued and between messages,
- IBI manual is used and no decision was made.
The maximum stall period is 100 μs.
This can be considered as being just a warning as the system IRQ latency
can easily be greater than 100us.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-7-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Upon IBIWON timeout, the SDA line will always be kept low if we don't emit
a stop. Calling svc_i3c_master_emit_stop() there will let the bus return to
idle state.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-6-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
MSTATUS[RXPEND] is only updated after the data transfer cycle started. This
creates an issue when the I3C clock is slow, and the CPU is running fast
enough that MSTATUS[RXPEND] may not be updated when the code reaches
checking point. As a result, mandatory data can be missed.
Add a wait for MSTATUS[COMPLETE] to ensure that all mandatory data is
already in FIFO. It also works without mandatory data.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-4-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
┌─────┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┌─────
SCL: ┘ └─────┛ └──┛ └──┛ └──┛ └──┛ └──┛ └──┛ └──┛ └──┘
───┐ ┌─────┐ ┌─────┐ ┌───────────┐
SDA: └───────────────────────┘ └─────┘ └─────┘ └─────
xxx╱ ╲╱ ╲╱ ╲╱ ╲╱ ╲
: xxx╲IBI ╱╲ Addr(0x0a) ╱╲ RW ╱╲NACK╱╲ S ╱
If an In-Band Interrupt (IBI) occurs and IBI work thread is not immediately
scheduled, when svc_i3c_master_priv_xfers() initiates the I3C transfer and
attempts to send address 0x7e, the target interprets it as an
IBI handler and returns the target address 0x0a.
However, svc_i3c_master_priv_xfers() does not handle this case and proceeds
with other transfers, resulting in incorrect data being returned.
Add IBIWON check in svc_i3c_master_xfer(). In case this situation occurs,
return a failure to the driver.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-3-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The ibi work thread operates asynchronously with other transfers, such as
svc_i3c_master_priv_xfers(). Introduce mutex protection to ensure the
completion of the entire i3c/i2c transaction.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-2-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This allows other drivers to be notified when new i3c busses are
attached, referring to a whole i3c bus as opposed to individual
devices.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The MIPI I3C spec refers to a Provisioned ID, since it is (sometimes)
provisioned at device manufacturing.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231003075339.197099-1-matt@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
put_device() needs to be called on failure of device_register()
to give up the reference initialized in it to avoid refcount leak.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20230921082410.25548-1-dinghao.liu@zju.edu.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Host Controller goes to halt state after aborted transfer and needs to
be resumed by SW. Add this resuming to DMA mode code too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-13-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On an HW I'm using in enabling work the RESUME bit is not set in the
HC_CONTROLLER register when Host Controller goes to halt state. Value 1
should mean controller is suspended when reading and writing 1 resumes it.
Because of this erratic behaviour plain HC_CONTROL read and write back
won't resume the controller. Therefore do it by setting the RESUME bit
explicitly.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-12-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Due to missing completion object for the ENTDAA command transfer in the
hci_cmd_v1_daa() the wait_for_completion_timeout() will obviously
timeout even the transfer itself may succeed.
Fix this by setting the xfer->completion to the already initialized
completion object.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-11-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix following warning (with CONFIG_DMA_API_DEBUG) which happens with a
transfer without a data buffer.
DMA-API: i3c mipi-i3c-hci.0: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=0 bytes]
For those transfers the hci_dma_queue_xfer() doesn't create a mapping and
the DMA address pointer xfer->data_dma is not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-10-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Number of software enabled Ring Bundles must be set before using them.
Otherwise Ring will not start and may be power-gated by the Host
Controller.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-9-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
If there is a transfer error during i3c_master_bus_init() and code goes
doing the bus cleanup in i3c_hci_bus_cleanup() there is possibility that
i3c_hci_irq_handler() is running in parallel with hci->io->cleanup()
which can be racy.
Prevent this by waiting there is no pending interrupt on other CPU
before doing the IO cleanup.
This was observed with ring headers where first transfer failed and
sometimes transfer error or ring transfer abort interrupt was coming
simultaneously with the bus cleanup path.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-8-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Set ring start request together with ring enable in hci_dma_init(). This
causes the ring abort request in hci_dma_dequeue_xfer() will raise the
INTR_RING_OP (RING_OP_STAT in MIPI I3C HCI specification) interrupt in
the RH_INTR_STATUS register.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-7-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Ring Abort request will timeout in case there is an error in the Host
Controller interrupt delivery or Ring Header configuration. Using BUG()
makes hard to debug those cases.
Make it less severe and turn BUG() to WARN_ON().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-6-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Do not loop over ring headers in hci_dma_irq_handler() that are not
allocated and enabled in hci_dma_init(). Otherwise out of bounds access
will occur from rings->headers[i] access when i >= number of allocated
ring headers.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-5-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
MIPI I3C HCI specification v1.1 describes the ENTRY_SIZE field for the
Device Address Table (DAT) and the Device Characteristics Table (DCT)
section offset registers (DAT_SECTION_OFFSET and DCT_SECTION_OFFSET).
That field is not documented in earlier version.
ENTRY_SIZE value 0 is meant to be backward compatible. For the DAT entry
size it is interpreted as 2 DWORDs (8-bytes) and for the DCT entry size
as 4 DWORDs (16-bytes). Values 1-15 are reserved for future use.
New version I believe fixes also the TABLE_SIZE field description.
Before it was defined in DWORDs which I believe is incorrect since the
DAT/DCT table entry structures, and sizes, are described having
8-bytes/16-bytes entries.
This is more clear in the specification v1.1 which states the TABLE_SIZE
fields are interpreted as number of entries in the DAT/DCT tables. I
believe this same holds also in earlier version, at least it makes more
sense.
Fix code accordingly and let the DAT_entry_size and the DCT_entry_size
variables carry the size as bytes. Which is how it is already
interpreted in the dat_v1.c: hci_dat_v1_init().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-4-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add MODULE_ALIAS() in order to be able to autoload this driver when the
device is added as a platform device from another glue code driver.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-3-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Copy the DMA masks and parameters for an I3C master device from parent
device so that the master device has them set for the DMA buffer and
mapping API.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct svc_i3c_xfer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Conor Culhane <conor.culhane@silvaco.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230922175023.work.239-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct hci_rings_data.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Nicolas Pitre <npitre@baylibre.com>
Cc: Len Baker <len.baker@gmx.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922175019.work.129-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct cdns_i3c_xfer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: "Przemysław Gaj" <pgaj@cadence.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922175014.work.637-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct dw_i3c_xfer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230922175011.work.800-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
`strncpy` is deprecated for use on NUL-terminated destination strings [1].
We should prefer more robust and less ambiguous string interfaces.
We expect adap->name to be NUL-terminated based on i2c_adapter name use:
| dev_dbg(&adap->dev, "adapter [%s] registered\n", adap->name);
NUL-padding does not seem to be required as `master` is zero-allocated
and `i3c_master_to_i2c_adapter` simply returns a field from within
`master`:
| master = devm_kzalloc(dev, sizeof(*master), GFP_KERNEL);
...
| struct i2c_adapter *adap = i3c_master_to_i2c_adapter(master);
...
| static struct i2c_adapter *
| i3c_master_to_i2c_adapter(struct i3c_master_controller *master)
| {
| return &master->i2c;
| }
This means that `adap->name` should already be filled with NUL-bytes.
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230921-strncpy-drivers-i3c-master-c-v1-1-9fdb8d8169e1@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I3C masters are expected to support hot-join. This means at initialization
time we might not yet discover any device and this should not be treated
as a fatal error.
During the DAA procedure which happens at probe time, if no device has
joined, all CCC will be NACKed (from a bus perspective). This leads to an
early return with an error code which fails the probe of the master.
Let's avoid this by just telling the core through an I3C_ERROR_M2
return command code that no device was discovered, which is a valid
situation. This way the master will no longer bail out and fail to probe
for a wrong reason.
Cc: stable@vger.kernel.org
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230831141324.2841525-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When a I3C DT node has a static_addr and an init_dyn_addr,the
init_dyn_addr is reserved in i3c_master_bus_init() and then
the static_addr is reserved in i3c_master_early_i3c_dev_add().
But if the dynamic address is same as static then above
procedure would fail.
Add a check to pass i3c_bus_get_addr_slot_status() when static
and dynamic address are equal.
Signed-off-by: Aniket <aniketmaurya@google.com>
Link: https://lore.kernel.org/r/20230822051938.2852567-1-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The 'saved_regs' member of the 'svc_i3c_master' structure is not
described in the kernel doc, which produces the following warning:
Function parameter or member 'saved_regs' not described in 'svc_i3c_master'
Add the missing line in the kernel documentation of the parent
structure.
Fixes: 1c5ee2a77b ("i3c: master: svc: fix i3c suspend/resume issue")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308171435.0xQ82lvu-lkp@intel.com/
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230817101853.16805-1-miquel.raynal@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It is not possible for platform_get_irq() to return 0. Use the
return value from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230803085149.149248-1-ruanjinjie@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The exit criteria for the DAA should check if the data length is equal to
1, instead of checking if the response status is equal to 1.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20230802100909.2568215-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230714174623.4057784-1-robh@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add NACK check after start byte is sent.
It is possible to detect early that a device is not on the bus
and avoid invalid transmissions thereafter.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230517033030.3068085-3-xiaoning.wang@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Dylan Hung