[ Upstream commit 415798bc07 ]
Commit d5e01266e7 ("leds: trigger: netdev: add additional specific link
speed mode") in the various changes, reworked the way to set the LINKUP
mode in commit cee4bd16c3 ("leds: trigger: netdev: Recheck
NETDEV_LED_MODE_LINKUP on dev rename") and moved it to a generic function.
This changed the logic where, in the previous implementation the dev
from the trigger event was used to check if the carrier was ok, but in
the new implementation with the generic function, the dev in
trigger_data is used instead.
This is problematic and cause a possible kernel panic due to the fact
that the dev in the trigger_data still reference the old one as the
new one (passed from the trigger event) still has to be hold and saved
in the trigger_data struct (done in the NETDEV_REGISTER case).
On calling of get_device_state(), an invalid net_dev is used and this
cause a kernel panic.
To handle this correctly, move the call to get_device_state() after the
new net_dev is correctly set in trigger_data (in the NETDEV_REGISTER
case) and correctly parse the new dev.
Fixes: d5e01266e7 ("leds: trigger: netdev: add additional specific link speed mode")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240203235413.1146-1-ansuelsmth@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
- Add support for Allwinner A100 RGB LED controller
- Add support for Maxim 5970 Dual Hot-swap controller
- New Device Support
- Add support for AW20108 to Awinic LED driver
- New Functionality
- Extend support for Net speeds to include; 2.5G, 5G and 10G
- Allow tx/rx and cts/dsr/dcd/rng TTY LEDS to be turned on and off via sysfs if required
- Add support for hardware control in AW200xx
- Fix-ups
- Use safer methods for string handling
- Improve error handling; return proper error values, simplify, avoid duplicates, etc
- Replace Mutex use with the Completion mechanism
- Fix include lists; alphabetise, remove unused, explicitly add used
- Use generic platform device properties
- Use/convert to new/better APIs/helpers/MACROs instead of hand-rolling implementations
- Device Tree binding adaptions/conversions/creation
- Continue work to remove superfluous platform .remove() call-backs
- Remove superfluous/defunct code
- Trivial; whitespace, unused variables, spelling, clean-ups, etc
- Avoid unnecessary duplicate locks
- Bug Fixes
- Repair Kconfig based dependency lists
- Ensure unused dynamically allocated data is freed after use
- Fix support for brightness control
- Add missing sufficient delays during reset to ensure correct operation
- Avoid division-by-zero issues
-----BEGIN PGP SIGNATURE-----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=/f98
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Drivers:
- Add support for Allwinner A100 RGB LED controller
- Add support for Maxim 5970 Dual Hot-swap controller
New Device Support:
- Add support for AW20108 to Awinic LED driver
New Functionality:
- Extend support for Net speeds to include; 2.5G, 5G and 10G
- Allow tx/rx and cts/dsr/dcd/rng TTY LEDS to be turned on and off
via sysfs if required
- Add support for hardware control in AW200xx
Fix-ups:
- Use safer methods for string handling
- Improve error handling; return proper error values, simplify,
avoid duplicates, etc
- Replace Mutex use with the Completion mechanism
- Fix include lists; alphabetise, remove unused, explicitly add used
- Use generic platform device properties
- Use/convert to new/better APIs/helpers/MACROs instead of
hand-rolling implementations
- Device Tree binding adaptions/conversions/creation
- Continue work to remove superfluous platform .remove() call-backs
- Remove superfluous/defunct code
- Trivial; whitespace, unused variables, spelling, clean-ups, etc
- Avoid unnecessary duplicate locks
Bug Fixes:
- Repair Kconfig based dependency lists
- Ensure unused dynamically allocated data is freed after use
- Fix support for brightness control
- Add missing sufficient delays during reset to ensure correct
operation
- Avoid division-by-zero issues"
* tag 'leds-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (45 commits)
leds: trigger: netdev: Add core support for hw not supporting fallback to LED sw control
leds: trigger: panic: Don't register panic notifier if creating the trigger failed
leds: sun50i-a100: Convert to be agnostic to property provider
leds: max5970: Add missing headers
leds: max5970: Make use of dev_err_probe()
leds: max5970: Make use of device properties
leds: max5970: Remove unused variable
leds: rgb: Drop obsolete dependency on COMPILE_TEST
leds: sun50i-a100: Avoid division-by-zero warning
leds: trigger: Remove unused function led_trigger_rename_static()
leds: qcom-lpg: Introduce a wrapper for getting driver data from a pwm chip
leds: gpio: Add kernel log if devm_fwnode_gpiod_get() fails
dt-bindings: leds: qcom,spmi-flash-led: Fix example node name
dt-bindings: leds: aw200xx: Fix led pattern and add reg constraints
dt-bindings: leds: awinic,aw200xx: Add AW20108 device
leds: aw200xx: Add support for aw20108 device
leds: aw200xx: Improve autodim calculation method
leds: aw200xx: Enable disable_locking flag in regmap config
leds: aw200xx: Add delay after software reset
dt-bindings: leds: aw200xx: Remove property "awinic,display-rows"
...
If hw doesn't support sw control of the LED and we switch to a mode
not supported by hw, currently we get lots of errors because neither
brigthness_set() nor brithness_set_blocking() is set.
Deal with this by not falling back to sw control, and return
-EOPNOTSUPP to the user. Note that we still store the new mode.
This is needed in case an intermediate unsupported mode is necessary
to switch from one supported mode to another.
Add a comment explaining how a driver for such hw is supposed to behave.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/3fd5184c-3641-4b0b-b59a-f489ec69a6cd@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
The serial tty interface also supports additional input signals, that
can also be evaluated within this trigger. This change is adding the
following additional input sources, which could be controlled
via the '/sys/class/<leds>/' sysfs interface.
Explanation:
DCE = Data Communication Equipment (Modem)
DTE = Data Terminal Equipment (Computer)
- cts:
DCE is ready to accept data from the DTE (CTS = Clear To Send). If
the line state is detected, the LED is switched on.
If set to 0 (default), the LED will not evaluate CTS.
If set to 1, the LED will evaluate CTS.
- dsr:
DCE is ready to receive and send data (DSR = Data Set Ready). If the
line state is detected, the LED is switched on.
If set to 0 (default), the LED will not evaluate DSR.
If set to 1, the LED will evaluate DSR.
- dcd:
DTE is receiving a carrier from the DCE (DCD = Data Carrier Detect).
If the line state is detected, the LED is switched on.
If set to 0 (default), the LED will not evaluate DCD.
If set to 1, the LED will evaluate DCD.
- rng:
DCE has detected an incoming ring signal on the telephone line
(RNG = Ring Indicator). If the line state is detected, the LED is
switched on.
If set to 0 (default), the LED will not evaluate RNG.
If set to 1, the LED will evaluate RNG.
Also add an invert flag on LED blink, so that the LED blinks in the
correct order.
* If one off the new enabled input signals are evaluatet as 'enabled',
and data are transmitted, then the LED should first blink 'off' and
then 'on' (invert).
* If all the new enabled input signals are evaluatet as 'disabled',
and data are transmitted, then the LED should first blink 'on' and
then 'off'.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Maarten Brock <m.brock@vanmierlo.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-5-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
Until now, the LED blinks when data is sent via the tty (rx/tx).
This is not configurable.
This change adds the possibility to make the indication for the direction
of the transmitted data independently controllable via the new rx and
tx sysfs entries.
- rx:
Signal reception (rx) of data on the named tty device.
If set to 0, the LED will not blink on reception.
If set to 1 (default), the LED will blink on reception.
- tx:
Signal transmission (tx) of data on the named tty device.
If set to 0, the LED will not blink on transmission.
If set to 1 (default), the LED will blink on transmission.
This new sysfs entry are on by default. Thus the trigger behaves as
before this change.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-4-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
With this commit, the mutex handling is replaced by the completion
handling. When handling mutex, it must always be ensured that the held
mutex is also released again. This is more error-prone should the number
of code paths increase.
This is a preparatory commit to make the trigger more configurable via
additional sysfs parameters. With this change, the worker always runs and
is no longer stopped if no ttyname is set.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-3-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
The ttyname buffer for the ledtrig_tty_data struct is allocated in the
sysfs ttyname_store() function. This buffer must be released on trigger
deactivation. This was missing and is thus a memory leak.
While we are at it, the TTY handler in the ledtrig_tty_data struct should
also be returned in case of the trigger deactivation call.
Cc: stable@vger.kernel.org
Fixes: fd4a641ac8 ("leds: trigger: implement a tty trigger")
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127081621.774866-1-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231103195310.948327-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
sscanf() is a heavy one and moreover requires additional boundary checks.
Convert driver to use kstrtou8() in gpio_trig_inverted_store().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231103195310.948327-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
gpiod_get_optional() and currently used fwnode_gpiod_get_index()
are both wrappers against the same engine internally. Since we
have a pointer to struct device there is no reason to use fwnode
type of GPIO call. So, replace the current fwnode call by respective
gpiod ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231103195310.948327-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
GCC 13.2 complains about array subscript 17 is above array bounds of
'char[16]' with IFNAMSIZ set to 16.
The warning is correct but this scenario is impossible.
set_device_name is called by device_name_store (store sysfs entry) and
netdev_trig_activate.
device_name_store already check if size is >= of IFNAMSIZ and return
-EINVAL. (making the warning scenario impossible)
netdev_trig_activate works on already defined interface, where the name
has already been checked and should already follow the condition of
strlen() < IFNAMSIZ.
Aside from the scenario being impossible, set_device_name can be
improved to both mute the warning and make the function safer.
To make it safer, move size check from device_name_store directly to
set_device_name and prevent any out of bounds scenario.
Cc: stable@vger.kernel.org
Fixes: 28a6a2ef18 ("leds: trigger: netdev: refactor code setting device name")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309192035.GTJEEbem-lkp@intel.com/
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20231007131042.15032-1-ansuelsmth@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
By providing a GPIO line as "trigger-sources" in the FWNODE
(such as from the device tree) and combining with the
GPIO trigger, we can support a GPIO LED trigger in a natural
way from the hardware description instead of using the
custom sysfs and deprecated global GPIO numberspace.
Example:
gpio: gpio@0 {
compatible "my-gpio";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
#trigger-source-cells = <2>;
};
leds {
compatible = "gpio-leds";
led-my-gpio {
label = "device:blue:myled";
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
default-state = "off";
linux,default-trigger = "gpio";
trigger-sources = <&gpio 1 GPIO_ACTIVE_HIGH>;
};
};
Make this the norm, unmark the driver as broken.
Delete the sysfs handling of GPIOs.
Since GPIO descriptors inherently can describe inversion,
the inversion handling can just be deleted.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230926-gpio-led-trigger-dt-v2-3-e06e458b788e@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
In order to teach the compiler that 'trig->name' will never be truncated,
we need to tell it that 'cpu' is not negative.
When building with W=1, this fixes the following warnings:
drivers/leds/trigger/ledtrig-cpu.c: In function ‘ledtrig_cpu_init’:
drivers/leds/trigger/ledtrig-cpu.c:155:56: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 5 [-Werror=format-truncation=]
155 | snprintf(trig->name, MAX_NAME_LEN, "cpu%d", cpu);
| ^~
drivers/leds/trigger/ledtrig-cpu.c:155:52: note: directive argument in the range [-2147483648, 7]
155 | snprintf(trig->name, MAX_NAME_LEN, "cpu%d", cpu);
| ^~~~~~~
drivers/leds/trigger/ledtrig-cpu.c:155:17: note: ‘snprintf’ output between 5 and 15 bytes into a destination of size 8
155 | snprintf(trig->name, MAX_NAME_LEN, "cpu%d", cpu);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 8f88731d05 ("led-triggers: create a trigger for CPU activity")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/3f4be7a99933cf8566e630da54f6ab913caac432.1695453322.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Lee Jones <lee@kernel.org>
- Add new framework to support Group Multi-Color (GMC) LEDs
- Offer an 'optional' API for non-essential LEDs
- Support obtaining 'max brightness' values from Device Tree
- Provide new led_classdev member 'color' (settable via DT and SYFS)
- Stop TTY Trigger from using the old LED_ON constraints
- Statically allocate leds_class
- New Drivers
- Add support for NXP PCA995x I2C Constant Current LED Driver
- New Device Support
- Add support for Siemens Simatic IPC BX-21 to Simatic IPC
- Fix-ups
- Some dependency / Kconfig tweaking
- Move final probe() functions back over from .probe_new()
- Simplify obtaining resources (memory, device data) using unified API helpers
- Bunch of Device Tree additions, conversions and adaptions
- Fix trivial styling issues; comments
- Ensure correct includes are present and remove some that are not required
- Omit the use of redundant casts and if relevant replace with better ones
- Use purpose-built APIs for various actions; sysfs_emit(), module_led_trigger()
- Remove a bunch of superfluous locking
- Bug Fixes
- Ensure error codes are correctly propagated back up the call chain
- Fix incorrect error values from being returned (missing '-')
- Ensure get'ed resources are put'ed to prevent leaks
- Use correct class when exporting module resources
- Fixing rounding (or lack there of) issues
- Fix 'always false' LED_COLOR_ID_MULTI BUG() check
-----BEGIN PGP SIGNATURE-----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=wNmv
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"Core Frameworks:
- Add new framework to support Group Multi-Color (GMC) LEDs
- Offer an 'optional' API for non-essential LEDs
- Support obtaining 'max brightness' values from Device Tree
- Provide new led_classdev member 'color' (settable via DT and SYFS)
- Stop TTY Trigger from using the old LED_ON constraints
- Statically allocate leds_class
New Drivers:
- Add support for NXP PCA995x I2C Constant Current LED Driver
New Device Support:
- Add support for Siemens Simatic IPC BX-21 to Simatic IPC
Fix-ups:
- Some dependency / Kconfig tweaking
- Move final probe() functions back over from .probe_new()
- Simplify obtaining resources (memory, device data) using unified
API helpers
- Bunch of Device Tree additions, conversions and adaptions
- Fix trivial styling issues; comments
- Ensure correct includes are present and remove some that are not
required
- Omit the use of redundant casts and if relevant replace with better
ones
- Use purpose-built APIs for various actions; sysfs_emit(),
module_led_trigger()
- Remove a bunch of superfluous locking
Bug Fixes:
- Ensure error codes are correctly propagated back up the call chain
- Fix incorrect error values from being returned (missing '-')
- Ensure get'ed resources are put'ed to prevent leaks
- Use correct class when exporting module resources
- Fixing rounding (or lack there of) issues
- Fix 'always false' LED_COLOR_ID_MULTI BUG() check"
* tag 'leds-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (40 commits)
leds: aw2013: Enable pull-up supply for interrupt and I2C
dt-bindings: leds: Document pull-up supply for interrupt and I2C
dt-bindings: leds: aw2013: Document interrupt
leds: uleds: Use module_misc_device macro to simplify the code
leds: trigger: netdev: Use module_led_trigger macro to simplify the code
dt-bindings: leds: Fix reference to definition of default-state
leds: turris-omnia: Drop unnecessary mutex locking
leds: turris-omnia: Use sysfs_emit() instead of sprintf()
leds: Make leds_class a static const structure
leds: Remove redundant of_match_ptr()
dt-bindings: leds: Add gpio-line-names to PCA9532 GPIO
leds: trigger: tty: Do not use LED_ON/OFF constants, use led_blink_set_oneshot instead
dt-bindings: leds: rohm,bd71828: Drop select:false
leds: Fix BUG_ON check for LED_COLOR_ID_MULTI that is always false
leds: multicolor: Use rounded division when calculating color components
leds: rgb: Add a multicolor LED driver to group monochromatic LEDs
dt-bindings: leds: Add binding for a multicolor group of LEDs
leds: class: Store the color index in struct led_classdev
leds: Provide devm_of_led_get_optional()
leds: pca995x: Fix MODULE_DEVICE_TABLE for OF
...
Commit b655892ffd ("leds: trigger: netdev: expose hw_control status
via sysfs") exposed to sysfs the flag that tells whether the LED trigger
is offloaded to hardware, under the name "hw_control", since that is the
name under which this setting is called in the code.
Everywhere else in kernel when some work that is normally done in
software can be made to be done by hardware instead, we use the word
"offloading" to describe this, e.g. "LED blinking is offloaded to
hardware".
Normally renaming sysfs entries is a no-go because of backwards
compatibility. But since this patch was not yet released in a stable
kernel, I think it is still possible to rename it, if there is
consensus.
Fixes: b655892ffd ("leds: trigger: netdev: expose hw_control status via sysfs")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230821121453.30203-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the module_led_trigger macro to simplify the code, which is the
same as declaring with module_init() and module_exit().
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230815075944.1089298-2-lizetao1@huawei.com
Signed-off-by: Lee Jones <lee@kernel.org>
The tty LED trigger uses the obsolete LED_ON & LED_OFF constants when
setting LED brightness. This is bad because the LED_ON constant is equal
to 1, and so when activating the tty LED trigger on a LED class device
with max_brightness greater than 1, the LED is dimmer than it can be
(when max_brightness is 255, the LED is very dimm indeed; some devices
translate 1/255 to 0, so the LED is OFF all the time).
Instead of directly setting brightness to a specific value, use the
led_blink_set_oneshot() function from LED core to configure the blink.
This function takes the current configured brightness as blink
brightness if not zero, and max brightness otherwise.
This also changes the behavior of the TTY LED trigger. Previously if
rx/tx stats kept changing, the LED was ON all the time they kept
changing. With this patch the LED will blink on TTY activity.
Fixes: fd4a641ac8 ("leds: trigger: implement a tty trigger")
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20230802090753.13611-1-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Ensure that the offloading of blinking is stopped when the trigger is
deactivated. Calling led_set_brightness() is documented as stopping
offload and setting the LED to a constant brightness.
Suggested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20230808210436.838995-5-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the netdev trigger is activates, it tries to determine what
device the LED blinks for, and what the current blink mode is.
The documentation for hw_control_get() says:
* Return 0 on success, a negative error number on failing parsing the
* initial mode. Error from this function is NOT FATAL as the device
* may be in a not supported initial state by the attached LED trigger.
*/
For the Marvell PHY and the Armada 370-rd board, the initial LED blink
mode is not supported by the trigger, so it returns an error. This
resulted in not getting the device the LED is blinking for. As a
result, the device is unknown and offloaded is never performed.
Change to condition to always get the device if offloading is
supported, and reduce the scope of testing for an error from
hw_control_get() to skip setting trigger internal state if there is an
error.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20230808210436.838995-2-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Add support for Intel Cherry Trail Whiskey Cove PMIC LEDs
- Add support for Awinic AW20036/AW20054/AW20072 LEDs
- New Device Support
- Add support for PMI632 LPG to QCom LPG
- Add support for PMI8998 to QCom Flash
- Add support for MT6331, WLEDs and MT6332 to Mediatek MT6323 PMIC
- New Functionality
- Implement the LP55xx Charge Pump
- Add support for suspend / resume to Intel Cherry Trail Whiskey Cove PMIC
- Add support for breathing mode to Intel Cherry Trail Whiskey Cove PMIC
- Enable per-pin resolution Pinctrl in LEDs GPIO
- Fix-ups
- Allow thread to sleep by switching from spinlock to mutex
- Add lots of Device Tree bindings / support
- Adapt relationships / dependencies driven by Kconfig
- Switch I2C drivers from .probe_new() to .probe()
- Remove superfluous / duplicate code
- Replace strlcpy() with strscpy() for efficiency and overflow prevention
- Staticify various functions
- Trivial: Fixing coding style
- Simplify / reduce code
- Bug Fixes
- Prevent NETDEV_LED_MODE_LINKUP from being cleared on rename
- Repair race between led_set_brightness(LED_{OFF,FULL})
- Fix Oops relating to sleeping in critical sections
- Clear LED_INIT_DEFAULT_TRIGGER flag when clearing the current trigger
- Do not leak resources in error handling paths
- Fix unsigned comparison which can never be negative
- Provide missing NULL terminating entries in tables
- Fix misnaming issues
-----BEGIN PGP SIGNATURE-----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=9kd5
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Drivers:
- Add support for Intel Cherry Trail Whiskey Cove PMIC LEDs
- Add support for Awinic AW20036/AW20054/AW20072 LEDs
New Device Support:
- Add support for PMI632 LPG to QCom LPG
- Add support for PMI8998 to QCom Flash
- Add support for MT6331, WLEDs and MT6332 to Mediatek MT6323 PMIC
New Functionality:
- Implement the LP55xx Charge Pump
- Add support for suspend / resume to Intel Cherry Trail Whiskey Cove PMIC
- Add support for breathing mode to Intel Cherry Trail Whiskey Cove PMIC
- Enable per-pin resolution Pinctrl in LEDs GPIO
Fix-ups:
- Allow thread to sleep by switching from spinlock to mutex
- Add lots of Device Tree bindings / support
- Adapt relationships / dependencies driven by Kconfig
- Switch I2C drivers from .probe_new() to .probe()
- Remove superfluous / duplicate code
- Replace strlcpy() with strscpy() for efficiency and overflow prevention
- Staticify various functions
- Trivial: Fixing coding style
- Simplify / reduce code
Bug Fixes:
- Prevent NETDEV_LED_MODE_LINKUP from being cleared on rename
- Repair race between led_set_brightness(LED_{OFF,FULL})
- Fix Oops relating to sleeping in critical sections
- Clear LED_INIT_DEFAULT_TRIGGER flag when clearing the current trigger
- Do not leak resources in error handling paths
- Fix unsigned comparison which can never be negative
- Provide missing NULL terminating entries in tables
- Fix misnaming issues"
* tag 'leds-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (53 commits)
leds: leds-mt6323: Adjust return/parameter types in wled get/set callbacks
leds: sgm3140: Add richtek,rt5033-led compatible
dt-bindings: leds: sgm3140: Document richtek,rt5033 compatible
dt-bindings: backlight: kinetic,ktz8866: Add missing type for "current-num-sinks"
dt-bindings: leds: Drop unneeded quotes
leds: Fix config reference for AW200xx driver
leds: leds-mt6323: Add support for WLEDs and MT6332
leds: leds-mt6323: Add support for MT6331 leds
leds: leds-mt6323: Open code and drop MT6323_CAL_HW_DUTY macro
leds: leds-mt6323: Drop MT6323_ prefix from macros and defines
leds: leds-mt6323: Specify registers and specs in platform data
dt-bindings: leds: leds-mt6323: Document mt6332 compatible
dt-bindings: leds: leds-mt6323: Document mt6331 compatible
leds: simatic-ipc-leds-gpio: Introduce more Kconfig switches
leds: simatic-ipc-leds-gpio: Split up into multiple drivers
leds: simatic-ipc-leds-gpio: Move two extra gpio pins into another table
leds: simatic-ipc-leds-gpio: Add terminating entries to gpio tables
leds: flash: leds-qcom-flash: Fix an unsigned comparison which can never be negative
leds: cht-wcove: Remove unneeded semicolon
leds: cht-wcove: Fix an unsigned comparison which can never be negative
...
Expose hw_control status via sysfs for the netdev trigger to give
userspace better understanding of the current state of the trigger and
the LED.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add additional modes for specific link duplex. Use ethtool APIs to get the
current link duplex and enable the LED accordingly. Under netdev event
handler the rtnl lock is already held and is not needed to be set to
access ethtool APIs.
This is especially useful for PHY and Switch that supports LEDs hw
control for specific link duplex.
Add additional modes:
- half_duplex: Turn on LED when link is half duplex
- full_duplex: Turn on LED when link is full duplex
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add additional modes for specific link speed. Use ethtool APIs to get the
current link speed and enable the LED accordingly. Under netdev event
handler the rtnl lock is already held and is not needed to be set to
access ethtool APIs.
This is especially useful for PHY and Switch that supports LEDs hw
control for specific link speed. (example scenario a PHY that have 2 LED
connected one green and one orange where the green is turned on with
1000mbps speed and orange is turned on with 10mpbs speed)
On mode set from sysfs we check if we have enabled split link speed mode
and reject enabling generic link mode to prevent wrong and redundant
configuration.
Rework logic on the set baseline state to support these new modes to
select if we need to turn on or off the LED.
Add additional modes:
- link_10: Turn on LED when link speed is 10mbps
- link_100: Turn on LED when link speed is 100mbps
- link_1000: Turn on LED when link speed is 1000mbps
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The qca8k_cled_hw_control_get() function which implements ->hw_control_get
sets the appropriate bits but does not clear them. This leads to an
uninitialized variable bug. Fix this by setting mode to zero at the
start.
Fixes: e0256648c8 ("net: dsa: qca8k: implement hw_control ops")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose netdev trigger modes to make them accessible by LED driver that
will support netdev trigger for hw control.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On netdev trigger activation, hw control may be already active by
default. If this is the case and a device is actually provided by
hw_control_get_device(), init the already active mode and set the
bool to hw_control bool to true to reflect the already set mode in the
trigger_data.
Co-developed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdev which the LED should blink for is configurable in
/sys/class/led/foo/device_name. Ensure when offloading that the
configured netdev is the same as the netdev the LED is associated
with. If it is not, only perform software blinking.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for LED hw control for the netdev trigger.
The trigger on calling set_baseline_state to configure a new mode, will
do various check to verify if hw control can be used for the requested
mode in can_hw_control() function.
It will first check if the LED driver supports hw control for the netdev
trigger, then will use hw_control_is_supported() and finally will call
hw_control_set() to apply the requested mode.
To use such mode, interval MUST be set to the default value and net_dev
MUST be set. If one of these 2 value are not valid, hw control will
never be used and normal software fallback is used.
The default interval value is moved to a define to make sure they are
always synced.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reject interval store with hw_control enabled. It's are currently not
supported and MUST be set to the default value with hw control enabled.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic check for hw control support. Check if the required API are
defined and check if the defined trigger supported in hw control for the
LED driver match netdev.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce function to check if the requested mode can use hw control in
preparation for hw control support. Currently everything is handled in
software so can_hw_control will always return false.
Add knob with the new value hw_control in trigger_data struct to
set hw control possible. Useful for future implementation to implement
in set_baseline_state() the required function to set the requested mode
using LEDs hw control ops and in other function to reject set if hw
control is currently active.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code into a helper, ready for it to be called at
other times. No intended behaviour change.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call netdev_{put, hold} of dev_{put, hold} will check NULL,
so there is no need to check before using dev_{put, hold},
remove it to silence the warnings:
./drivers/leds/trigger/ledtrig-netdev.c:291:3-10: WARNING: NULL check before dev_{put, hold} functions is not needed.
./drivers/leds/trigger/ledtrig-netdev.c:401:2-9: WARNING: NULL check before dev_{put, hold} functions is not needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=4929
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230511070820.52731-1-yang.lee@linux.alibaba.com
Signed-off-by: Lee Jones <lee@kernel.org>
led_blink_set[_oneshot]()'s delay_on and delay_off function parameters
are pass by reference, so that hw-blink implementations can report
back the actual achieved delays when the values have been rounded
to something the hw supports.
This is really only interesting for the sysfs API / the timer trigger.
Other triggers don't really care about this and none of the callers of
led_trigger_blink[_oneshot]() do anything with the returned delay values.
Change the led_trigger_blink[_oneshot]() delay parameters to pass-by-value,
there are 2 reasons for this:
1. led_cdev->blink_set() may sleep, while led_trigger_blink() may not.
So on hw where led_cdev->blink_set() sleeps the call needs to be deferred
to a workqueue, in which case the actual achieved delays are unknown
(this is a preparation patch for the deferring).
2. Since the callers don't care about the actual achieved delays, allowing
callers to directly pass a value leads to simpler code for most callers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20230510162234.291439-2-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
Some LEDs may require to sleep while doing some operation like setting
brightness and other cleanup.
For this reason, using a spinlock will cause a sleep under spinlock
warning.
It should be safe to convert this to a sleepable lock since:
- sysfs read/write can sleep
- netdev_trig_work is a work queue and can sleep
- netdev _trig_notify can sleep
The spinlock was used when brightness didn't support sleeping, but this
changed and now it supported with brightness_set_blocking().
Convert to mutex lock to permit sleeping using brightness_set_blocking().
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-6-ansuelsmth@gmail.com
Convert link tx and rx device attr to a common macro to reduce common
code and in preparation for additional attr.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-5-ansuelsmth@gmail.com
Rename NETDEV trigger enum modes to a more symbolic name and add a
namespace to them.
Also add __TRIGGER_NETDEV_MAX to identify the max modes of the netdev
trigger.
This is a cleanup to drop the define and no behaviour change are
intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-4-ansuelsmth@gmail.com
Putting NETDEV_LED_MODE_LINKUP in the same list of the netdev trigger
modes is wrong as it's used to set the link state of the device and not
to set a blink mode as it's done by NETDEV_LED_LINK, NETDEV_LED_TX and
NETDEV_LED_RX. It's also wrong to put this state in the same bitmap of the
netdev trigger mode and should be external to it.
Drop NETDEV_LED_MODE_LINKUP from mode list and convert to a simple bool
that will be true or false based on the carrier link. No functional
change intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-3-ansuelsmth@gmail.com
Dev can be renamed also while up for supported device. We currently
wrongly clear the NETDEV_LED_MODE_LINKUP flag on NETDEV_CHANGENAME
event.
Fix this by rechecking if the carrier is ok on NETDEV_CHANGENAME and
correctly set the NETDEV_LED_MODE_LINKUP bit.
Fixes: 5f820ed523 ("leds: trigger: netdev: fix handling on interface rename")
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-2-ansuelsmth@gmail.com
The GPIO LED trigger exposes a userspace ABI where a user
can echo a GPIO number from the global GPIO numberspace into
a file that will trigger a certain LED when active.
This is problematic because the global GPIO numberspace is
inherently instable. The trigger came about at a time when
systems had one GPIO controller that defined hard-wired
GPIOs numbered 0..N and this number space was stable.
We have since moved to dynamic allocation of GPIO numbers
and there is no real guarantee that a GPIO number will stay
consistent even across a reboot: consider a USB attached
GPIO controller for example. Or two. Or the effect of
probe order after adding -EPROBE_DEFER to the kernel.
The trigger was added to support keypad LEDs on the Nokia
n810 from the GPIO event when a user slides up/down the
keypad. This is arch/arm/boot/dts/omap2420-n810.dts.
A userspace script is needed to activate the trigger.
This will be broken unless the script was updated recently
since the OMAP GPIO controller now uses dynamic GPIO
number allocations.
I want to know that this trigger has active users that
cannot live without it if we are to continue to support it.
Option if this is really needed: I can develop a new trigger
that can associate GPIOs with LEDs as triggers using device
tree, which should also remove the use of userspace custom
scripts to achieve this and be much more trustworthy, if
someone with the Nokia n810 or a device with a similar need
is willing to test it.
Suggested-by Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230314210059.419159-1-linus.walleij@linaro.org
No user of ide-disk remains, so remove this deprecated trigger.
Only a few platforms used this and were fixed in 2016.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230131140304.626779-2-clabbe@baylibre.com
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace the open-code with sysfs_emit() to simplify the code.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The CPU trigger is invoked on ARM from CPU-idle. That trigger later
invokes led_trigger_event() which may invoke the callback of the actual driver.
That driver can acquire a spinlock_t which is okay on kernel without
PREEMPT_RT. On a PREEMPT_RT enabled kernel this lock is turned into a
sleeping lock and must not be acquired with disabled interrupts.
Disable the CPU trigger on PREEMPT_RT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lkml.kernel.org/r/20210924111501.m57cwwn7ahiyxxdd@linutronix.de
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Commit b7fb14d3ac ("ide: remove the legacy ide driver") removes the
definition of the config IDE_GD_ATA.
So, remove the obsolete reference in ./drivers/leds/trigger/Kconfig.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Christian Marangi