Depending on BIOS configuration IOSM driver exchanges
protocol required for putting device into D3L2 or D3L1.2.
ipc_pcie_suspend_s2idle() is implemented to put device to D3L1.2.
This patch forces PCI core know this device should stay at D0.
- pci_save_state()is expensive since it does a lot of slow PCI
config reads.
The reported issue is not observed on x86 platform. The supurios
wake on AMD platform needs to be futher debugged with orignal patch
submitter [1]. Also the impact of adding pci_save_state() needs to be
assessed by testing it on other platforms.
This reverts commit f4dd5174e273("net: wwan: iosm: Keep device
at D0 for s2idle case").
[1] https://lore.kernel.org/all/20211224081914.345292-2-kai.heng.feng@canonical.com/
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Link: https://lore.kernel.org/r/20220104150213.1894-1-m.chetan.kumar@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We are seeing spurious wakeup caused by Intel 7560 WWAN on AMD laptops.
This prevent those laptops to stay in s2idle state.
>From what I can understand, the intention of ipc_pcie_suspend() is to
put the device to D3cold, and ipc_pcie_suspend_s2idle() is to keep the
device at D0. However, the device can still be put to D3hot/D3cold by
PCI core.
So explicitly let PCI core know this device should stay at D0, to solve
the spurious wakeup.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_pm_suspend_noirq() and pci_pm_resume_noirq() already handle power
transition for system-wide suspend and resume, so it's not necessary to
do it in the driver.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checkpatch warning in iosm_ipc_mmio.c
- Alignment should match open parenthesis
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ipc_wwan_tx_flowctrl() is declared in iosm_ipc_wwan.h but is
not defined.
Removed the dead code.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If there is no active IP session (interface up & running) then
release the data channel.
Use nr_sessions variable to track current active IP sessions.
If the count drops to 0, then send pipe close ctrl message to
release the data channel.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set wwan net dev tx queue len to DEFAULT_TX_QUEUE_LEN.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ev_cdev_write_pending flag is preventing a TX message post for
AT port while MBIM transfer is ongoing.
Removed the unnecessary check around control port TX transfer.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Devlink initialization flow was overwriting the IP traffic
channel configuration. This was causing wwan0 network interface
to be unusable after fw flash.
When device boots to fully functional mode restore the IP channel
configuration.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In TX packet accumulation flow transport layer is
giving a doorbell to device even though there is
no pending control TX transfer that needs immediate
attention.
Introduced a new hpda_ctrl_pending variable to keep
track of pending control TX transfer. If there is a
pending control TX transfer which needs an immediate
attention only then give a doorbell to device.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Debugfs interface is optional for the regular modem use. Some distros
and users will want to disable this feature for security or kernel
size reasons. So add a configuration option that allows to completely
disable the debugfs interface of the WWAN devices.
A primary considered use case for this option was embedded firmwares.
For example, in OpenWrt, you can not completely disable debugfs, as a
lot of wireless stuff can only be configured and monitored with the
debugfs knobs. At the same time, reducing the size of a kernel and
modules is an essential task in the world of embedded software.
Disabling the WWAN and IOSM debugfs interfaces allows us to save 50K
(x86-64 build) of space for module storage. Not much, but already
considerable when you only have 16MB of storage.
So it is hard to just disable whole debugfs. Users need some fine
grained set of options to control which debugfs interface is important
and should be available and which is not.
The new configuration symbol is enabled by default and is hidden under
the EXPERT option. So a regular user would not be bothered by another
one configuration question. While an embedded distro maintainer will be
able to a little more reduce the final image size.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The modem traces collection is a device (and so driver) specific option.
Therefore, move the related debugfs files into a driver-specific
subdirectory under the common per WWAN device directory.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Collecting modem firmware traces is optional for the regular modem use.
There are not many reasons for aborting device initialization due to an
inability to initialize the trace port and (or) its debugfs interface.
So, demote the initialization failure erro message into a warning and do
not break the initialization sequence in this case. Rework packet
processing and deinitialization so that they do not crash in case of
uninitialized trace port.
This change is mainly a preparation for an upcoming configuration option
introduction that will help disable driver debugfs functionality.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the channel related structures initialization from
ipc_imem_channel_init() to ipc_trace_init() and call it directly. On the
one hand, this makes the trace port initialization symmetric to the
deitialization, that is, it removes the additional wrapper.
On the other hand, this change consolidates the trace port related code
into a single source file, what facilitates an upcoming disabling of
this functionality by a user choise.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The iosm driver started using relayfs, but is missing the Kconfig
logic to ensure it's built into the kernel:
x86_64-linux-ld: drivers/net/wwan/iosm/iosm_ipc_trace.o: in function `ipc_trace_create_buf_file_handler':
iosm_ipc_trace.c:(.text+0x16): undefined reference to `relay_file_operations'
x86_64-linux-ld: drivers/net/wwan/iosm/iosm_ipc_trace.o: in function `ipc_trace_subbuf_start_handler':
iosm_ipc_trace.c:(.text+0x31): undefined reference to `relay_buf_full'
x86_64-linux-ld: drivers/net/wwan/iosm/iosm_ipc_trace.o: in function `ipc_trace_ctrl_file_write':
iosm_ipc_trace.c:(.text+0xd5): undefined reference to `relay_flush'
x86_64-linux-ld: drivers/net/wwan/iosm/iosm_ipc_trace.o: in function `ipc_trace_port_rx':
Fixes: 00ef32565b ("net: wwan: iosm: device trace collection using relayfs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Link: https://lore.kernel.org/r/20211204174033.950528-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The BAM Data Multiplexer provides access to the network data channels of
modems integrated into many older Qualcomm SoCs, e.g. Qualcomm MSM8916 or
MSM8974. It is built using a simple protocol layer on top of a DMA engine
(Qualcomm BAM) and bidirectional interrupts to coordinate power control.
The modem announces a fixed set of channels by sending an OPEN command.
The driver exports each channel as separate network interface so that
a connection can be established via QMI from userspace. The network
interface can work either in Ethernet or Raw-IP mode (configurable via
QMI). However, Ethernet mode seems to be broken with most firmwares
(network packets are actually received as Raw-IP), therefore the driver
only supports Raw-IP mode.
Note that the control channel (QMI/AT) is entirely separate from
BAM-DMUX and is already supported by the RPMSG_WWAN_CTRL driver.
The driver uses runtime PM to coordinate power control with the modem.
TX/RX buffers are put in a kind of "ring queue" and submitted via
the bam_dma driver of the DMAEngine subsystem.
The basic architecture looks roughly like this:
+------------+ +-------+
[IPv4/6] | BAM-DMUX | | |
[Data...] | | | |
---------->|wwan0 | [DMUX chan: x] | |
[IPv4/6] | (chan: 0) | [IPv4/6] | |
[Data...] | | [Data...] | |
---------->|wwan1 |--------------->| Modem |
| (chan: 1) | BAM | |
[IPv4/6] | ... | (DMA Engine) | |
[Data...] | | | |
---------->|wwan7 | | |
| (chan: 7) | | |
+------------+ +-------+
Note that some newer firmware versions support QMAP ("rmnet" driver)
as additional multiplexing layer on top of BAM-DMUX, but this is not
currently supported by this driver.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch brings in support for device trace collection.
It implements relayfs interface for pushing device trace
from kernel space to user space.
Driver gets the debugfs base directory associated to WWAN
Device and creates trace_control and trace debugfs for
device tracing. Both trace_control & trace debugfs are
created under /sys/kernel/debug/wwan/wwan0/.
In order to collect device trace on trace0 interface, user
need to write 1 to trace_ctl interface.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch set brings in a common debugfs base directory
i.e. /sys/kernel/debugfs/wwan/ in WWAN Subsystem for a
WWAN device instance. So that it avoids driver polluting
debugfs root with unrelated directories & possible name
collusion.
Having a common debugfs base directory for WWAN drivers
eases user to match control devices with debugfs entries.
WWAN Subsystem creates dentry (/sys/kernel/debugfs/wwan)
on module load & removes dentry on module unload.
When driver registers a new wwan device, dentry (wwanX)
is created for WWAN device instance & on driver unregister
dentry is removed.
New API is introduced to return the wwan device instance
dentry so that driver can create debugfs entries under it.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
curr_phase is unused. Removed the dead code.
Fixes: 8d9be06341 ("net: wwan: iosm: transport layer support for fw flashing/cd")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Removed driver specific extra params like download_region,
address & region_count. The required information is passed
as part of flash API.
2. IOSM Devlink documentation updated to reflect the same.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change prevents from users to access device before devlink is
fully configured. Indirectly this change fixes the commit mentioned
below where devlink_unregister() was prematurely removed.
Fixes: db4278c55f ("devlink: Make devlink_register to be void")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hrtimer_forward_now() is providing the same functionality. Preparation for
making hrtimer_forward() timer core code only.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Loic Poulain <loic.poulain@linaro.org>
Cc: netdev@vger.kernel.org
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: M Chetan Kumar <m.chetan.kumar@intel.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Intel Corporation <linuxwwan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1> Function comments moved to .c file.
2> Use literals in return to improve readability.
3> Do error handling check instead of success check.
4> Redundant ret assignment removed.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink_register() can't fail and always returns success, but all drivers
are obligated to check returned status anyway. This adds a lot of boilerplate
code to handle impossible flow.
Make devlink_register() void and simplify the drivers that use that
API call.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com> # dsa
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOSM Makefile & WWAN Kconfig changes to support fw flashing & cd
collection module compliation.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements transport layer protocol for fw flashing/coredump
collection.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements protocol for coredump collection.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements protocol for fw flashing and PSI injection for
coredump collection.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register with devlink framework and implment callbacks required
for fw flashing and coredump collection.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink parameters are not the right mechanism to pass
extra parameters to device flashing. The params added are
also undocumented.
This reverts commit 13bb8429ca ("net: wwan: iosm: firmware
flashing and coredump collection").
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed "stdbool.h" inclusion in iosm_ipc_imem.h
Fixes: 13bb8429ca ("net: wwan: iosm: firmware flashing and coredump collection")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch brings-in support for M.2 7560 Device firmware flashing &
coredump collection using devlink.
- Driver Registers with Devlink framework.
- Register devlink params callback for configuring device params
required in flashing or coredump flow.
- Implements devlink ops flash_update callback that programs modem
firmware.
- Creates region & snapshot required for device coredump log collection.
On early detection of device in boot rom stage. Driver registers with
Devlink framework and establish transport channel for PSI (Primary Signed
Image) injection. Once PSI is injected to device, the device execution
stage details are read to determine whether device is in flash or
exception mode. The collected information is reported to devlink user
space application & based on this informationi, application proceeds with
either modem firmware flashing or coredump collection.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
wireless and can.
Current release - regressions:
- qrtr: revert check in qrtr_endpoint_post(), fixes audio and wifi
- ip_gre: validate csum_start only on pull
- bnxt_en: fix 64-bit doorbell operation on 32-bit kernels
- ionic: fix double use of queue-lock, fix a sleeping in atomic
- can: c_can: fix null-ptr-deref on ioctl()
- cs89x0: disable compile testing on powerpc
Current release - new code bugs:
- bridge: mcast: fix vlan port router deadlock, consistently disable BH
Previous releases - regressions:
- dsa: tag_rtl4_a: fix egress tags, only port 0 was working
- mptcp: fix possible divide by zero
- netfilter: nft_ct: protect nft_ct_pcpu_template_refcnt with mutex
- netfilter: socket: icmp6: fix use-after-scope
- stmmac: fix MAC not working when system resume back with WoL active
Previous releases - always broken:
- ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL
address
- seg6: set fc_nlinfo in nh_create_ipv4, nh_create_ipv6
- mptcp: only send extra TCP acks in eligible socket states
- dsa: lantiq_gswip: fix maximum frame length
- stmmac: fix overall budget calculation for rxtx_napi
- bnxt_en: fix firmware version reporting via devlink
- renesas: sh_eth: add missing barrier to fix freeing wrong tx descriptor
Stragglers:
- netfilter: conntrack: switch to siphash
- netfilter: refuse insertion if chain has grown too large
- ncsi: add get MAC address command to get Intel i210 MAC address
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Zvuz
-----END PGP SIGNATURE-----
Merge tag 'net-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes and stragglers from Jakub Kicinski:
"Networking stragglers and fixes, including changes from netfilter,
wireless and can.
Current release - regressions:
- qrtr: revert check in qrtr_endpoint_post(), fixes audio and wifi
- ip_gre: validate csum_start only on pull
- bnxt_en: fix 64-bit doorbell operation on 32-bit kernels
- ionic: fix double use of queue-lock, fix a sleeping in atomic
- can: c_can: fix null-ptr-deref on ioctl()
- cs89x0: disable compile testing on powerpc
Current release - new code bugs:
- bridge: mcast: fix vlan port router deadlock, consistently disable
BH
Previous releases - regressions:
- dsa: tag_rtl4_a: fix egress tags, only port 0 was working
- mptcp: fix possible divide by zero
- netfilter: nft_ct: protect nft_ct_pcpu_template_refcnt with mutex
- netfilter: socket: icmp6: fix use-after-scope
- stmmac: fix MAC not working when system resume back with WoL active
Previous releases - always broken:
- ip/ip6_gre: use the same logic as SIT interfaces when computing
v6LL address
- seg6: set fc_nlinfo in nh_create_ipv4, nh_create_ipv6
- mptcp: only send extra TCP acks in eligible socket states
- dsa: lantiq_gswip: fix maximum frame length
- stmmac: fix overall budget calculation for rxtx_napi
- bnxt_en: fix firmware version reporting via devlink
- renesas: sh_eth: add missing barrier to fix freeing wrong tx
descriptor
Stragglers:
- netfilter: conntrack: switch to siphash
- netfilter: refuse insertion if chain has grown too large
- ncsi: add get MAC address command to get Intel i210 MAC address"
* tag 'net-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits)
ieee802154: Remove redundant initialization of variable ret
net: stmmac: fix MAC not working when system resume back with WoL active
net: phylink: add suspend/resume support
net: renesas: sh_eth: Fix freeing wrong tx descriptor
bonding: 3ad: pass parameter bond_params by reference
cxgb3: fix oops on module removal
can: c_can: fix null-ptr-deref on ioctl()
can: rcar_canfd: add __maybe_unused annotation to silence warning
net: wwan: iosm: Unify IO accessors used in the driver
net: wwan: iosm: Replace io.*64_lo_hi() with regular accessors
net: qcom/emac: Replace strlcpy with strscpy
ip6_gre: Revert "ip6_gre: add validation for csum_start"
net: hns3: make hclgevf_cmd_caps_bit_map0 and hclge_cmd_caps_bit_map0 static
selftests/bpf: Test XDP bonding nest and unwind
bonding: Fix negative jump label count on nested bonding
MAINTAINERS: add VM SOCKETS (AF_VSOCK) entry
stmmac: dwmac-loongson:Fix missing return value
iwlwifi: fix printk format warnings in uefi.c
net: create netdev->dev_addr assignment helpers
bnxt_en: Fix possible unintended driver initiated error recovery
...
Currently we have readl()/writel()/ioread*()/iowrite*() APIs in use.
Let's unify to use only ioread*()/iowrite*() variants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The io.*_lo_hi() variants are not strictly needed on the x86 hardware
and especially the PCI bus. Replace them with regular accessors, but
leave headers in place in case of 32-bit build.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add -s option (strict mode) to merge_config.sh to make it fail when
any symbol is redefined.
- Show a warning if a different compiler is used for building external
modules.
- Infer --target from ARCH for CC=clang to let you cross-compile the
kernel without CROSS_COMPILE.
- Make the integrated assembler default (LLVM_IAS=1) for CC=clang.
- Add <linux/stdarg.h> to the kernel source instead of borrowing
<stdarg.h> from the compiler.
- Add Nick Desaulniers as a Kbuild reviewer.
- Drop stale cc-option tests.
- Fix the combination of CONFIG_TRIM_UNUSED_KSYMS and CONFIG_LTO_CLANG
to handle symbols in inline assembly.
- Show a warning if 'FORCE' is missing for if_changed rules.
- Various cleanups
-----BEGIN PGP SIGNATURE-----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=lw3M
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Add -s option (strict mode) to merge_config.sh to make it fail when
any symbol is redefined.
- Show a warning if a different compiler is used for building external
modules.
- Infer --target from ARCH for CC=clang to let you cross-compile the
kernel without CROSS_COMPILE.
- Make the integrated assembler default (LLVM_IAS=1) for CC=clang.
- Add <linux/stdarg.h> to the kernel source instead of borrowing
<stdarg.h> from the compiler.
- Add Nick Desaulniers as a Kbuild reviewer.
- Drop stale cc-option tests.
- Fix the combination of CONFIG_TRIM_UNUSED_KSYMS and CONFIG_LTO_CLANG
to handle symbols in inline assembly.
- Show a warning if 'FORCE' is missing for if_changed rules.
- Various cleanups
* tag 'kbuild-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (39 commits)
kbuild: redo fake deps at include/ksym/*.h
kbuild: clean up objtool_args slightly
modpost: get the *.mod file path more simply
checkkconfigsymbols.py: Fix the '--ignore' option
kbuild: merge vmlinux_link() between ARCH=um and other architectures
kbuild: do not remove 'linux' link in scripts/link-vmlinux.sh
kbuild: merge vmlinux_link() between the ordinary link and Clang LTO
kbuild: remove stale *.symversions
kbuild: remove unused quiet_cmd_update_lto_symversions
gen_compile_commands: extract compiler command from a series of commands
x86: remove cc-option-yn test for -mtune=
arc: replace cc-option-yn uses with cc-option
s390: replace cc-option-yn uses with cc-option
ia64: move core-y in arch/ia64/Makefile to arch/ia64/Kbuild
sparc: move the install rule to arch/sparc/Makefile
security: remove unneeded subdir-$(CONFIG_...)
kbuild: sh: remove unused install script
kbuild: Fix 'no symbols' warning when CONFIG_TRIM_UNUSD_KSYMS=y
kbuild: Switch to 'f' variants of integrated assembler flag
kbuild: Shuffle blank line to improve comment meaning
...
This reverts commit ce78ffa3ef.
Wren and Nicolas reported that ath11k was failing to initialise QCA6390
Wi-Fi 6 device with error:
qcom_mhi_qrtr: probe of mhi0_IPCR failed with error -22
Commit ce78ffa3ef ("net: really fix the build..."), introduced in
v5.14-rc5, caused this regression in qrtr. Most likely all ath11k
devices are broken, but I only tested QCA6390. Let's revert the broken
commit so that ath11k works again.
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210826172816.24478-1-kvalo@codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Delete/fixup few includes in anticipation of global -isystem compile
option removal.
Note: crypto/aegis128-neon-inner.c keeps <stddef.h> due to redefinition
of uintptr_t error (one definition comes from <stddef.h>, another from
<linux/types.h>).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The bounds check on "index" doesn't catch negative values. Using
ARRAY_SIZE() directly is more readable and more robust because it prevents
negative values for "index". Fortunately we only pass valid values to
ipc_chnl_cfg_get() so this patch does not affect runtime.
Reported-by: Solomon Ucko <solly.ucko@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make wwan_create_dev() to return either valid or error pointer,
In some cases it may return NULL. Prevent this by converting
it to the respective error pointer.
Fixes: 9a44c1cc63 ("net: Add a WWAN subsystem")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/20210811124845.10955-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ida_alloc_range() may return other than -ENOMEM error code.
Unshadow it in the wwan_create_port().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver allocates the spinlock but not initialize it.
Use spin_lock_init() on it to initialize it correctly.
Fixes: aa730a9905 ("net: wwan: Add MHI MBIM network driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lockdep detected possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&mhiwwan->rx_lock);
local_irq_disable();
lock(&mhi_cntrl->pm_lock);
lock(&mhiwwan->rx_lock);
<Interrupt>
lock(&mhi_cntrl->pm_lock);
*** DEADLOCK ***
To prevent this we need to disable the soft-interrupts when taking
the rx_lock.
Cc: stable@vger.kernel.org
Fixes: fa588eba63 ("net: Add Qcom WWAN control driver")
Reported-by: Thomas Perrot <thomas.perrot@bootlin.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df93 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098 ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df93 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Calling unregister_netdevice() inside wwan del link is trying to
acquire the held lock in ndo_stop_cb(). Instead, queue net dev to
be unregistered later.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct ul/dl data protocol mask bit to know which protocol capability
does device implement.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Endianness type correction for nr_of_bytes. This field is exchanged
as part of host-device protocol communication.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct td buffer type casting & format specifier to fix lkp buildbot
warning.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new wwan driver for MBIM over MHI. MBIM is a transport protocol
for IP packets, allowing packet aggregation and muxing. Initially
designed for USB bus, it is also exposed through MHI bus for QCOM
based PCIe wwan modems.
This driver supports the new wwan rtnetlink interface for multi-link
management and has been tested with Quectel EM120R-GL M2 module.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A wwan link created via the wwan_create_default_link procedure is
never notified to the user (RTM_NEWLINK), causing issues with user
tools relying on such event to track network links (NetworkManager).
This is because the procedure misses a call to rtnl_configure_link(),
which sets the link as initialized and notifies the new link (cf
proper usage in __rtnl_newlink()).
Cc: stable@vger.kernel.org
Fixes: ca374290aa ("wwan: core: support default netdev creation")
Suggested-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A wwan link created via the wwan_create_default_link procedure is
never notified to the user (RTM_NEWLINK), causing issues with user
tools relying on such event to track network links (NetworkManager).
This is because the procedure misses a call to rtnl_configure_link(),
which sets the link as initialized and notifies the new link (cf
proper usage in __rtnl_newlink()).
Cc: stable@vger.kernel.org
Fixes: ca374290aa ("wwan: core: support default netdev creation")
Suggested-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate some boilerplate code by using module_pci_driver() instead of
init/exit, moving the salient bits from init into probe.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set netdev default mtu size to 1500.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update tx stats on successful packet consume, drop.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link ID to be kept intact with MBIM session ID
Ex: ID 0 should be associated to MBIM session ID 0.
Reported-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove reduandant IP session id check since required checks
are in place under caller.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change uevent env variable name to IOSM_EVENT & correct
reporting format to key=value pair.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WWAN core not only multiplex the netdev configuration data, but
process it too, and needs some space to store its private data
associated with the netdev. Add a structure to keep common WWAN core
data. The structure will be stored inside the netdev private data before
WWAN driver private data and have a field to make it easier to access
the driver data. Also add a helper function that simplifies drivers
access to their data.
At the moment we use the common WWAN private data to store the WWAN data
link (channel) id at the time the link is created, and report it back to
user using the .fill_info() RTNL callback. This should help the user to
be aware which network interface is bound to which WWAN device data
channel.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
CC: M Chetan Kumar <m.chetan.kumar@intel.com>
CC: Intel Corporation <linuxwwan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the just introduced WWAN core feature to create a default netdev
for the default data (IP MUX) channel.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
CC: M Chetan Kumar <m.chetan.kumar@intel.com>
CC: Intel Corporation <linuxwwan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most, if not each WWAN device driver will create a netdev for the
default data channel. Therefore, add an option for the WWAN netdev ops
registration function to create a default netdev for the WWAN device.
A WWAN device driver should pass a default data channel link id to the
ops registering function to request the creation of a default netdev, or
a special value WWAN_NO_DEFAULT_LINK to inform the WWAN core that the
default netdev should not be created.
For now, only wwan_hwsim utilize the default link creation option. Other
drivers will be reworked next.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
CC: M Chetan Kumar <m.chetan.kumar@intel.com>
CC: Intel Corporation <linuxwwan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WWAN netdev ops owner holding was used to protect from the
unexpected memory disappear. This approach causes a dependency cycle
(driver -> core -> driver) and effectively prevents a WWAN driver
unloading. E.g. WWAN hwsim could not be unloaded until all simulated
devices are removed:
~# modprobe wwan_hwsim devices=2
~# lsmod | grep wwan
wwan_hwsim 16384 2
wwan 20480 1 wwan_hwsim
~# rmmod wwan_hwsim
rmmod: ERROR: Module wwan_hwsim is in use
~# echo > /sys/kernel/debug/wwan_hwsim/hwsim0/destroy
~# echo > /sys/kernel/debug/wwan_hwsim/hwsim1/destroy
~# lsmod | grep wwan
wwan_hwsim 16384 0
wwan 20480 1 wwan_hwsim
~# rmmod wwan_hwsim
For a real device driver this will cause an inability to unload module
until a served device is physically detached.
Since the last commit we are removing all child netdev(s) when a driver
unregister the netdev ops. This allows us to permit the driver
unloading, since any sane driver will call ops unregistering on a device
deinitialization. So, remove the holding of an ops owner to make it
easier to unload a driver module. The owner field has also beed removed
from the ops structure as there are no more users of this field.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the last commit, the WWAN core will remove all our network
interfaces for us at the time of the WWAN netdev ops unregistering.
Therefore, we can safely drop the custom code that cleans the list of
created netdevs. Anyway it no longer removes any netdev, since all
netdevs were removed earlier in the wwan_unregister_ops() call.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: M Chetan Kumar <m.chetan.kumar@intel.com>
CC: M Chetan Kumar <m.chetan.kumar@intel.com>
CC: Intel Corporation <linuxwwan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use the ops owner module hold to protect against ops memory
disappearing. But this approach does not protect us from a driver that
unregisters ops but forgets to remove netdev(s) that were created using
this ops. In such case, we are left with netdev(s), which can not be
removed since ops is gone. Moreover, batch netdevs removing on
deinitialization is a desireable option for WWAN drivers as it is a
quite common task.
Implement deletion of all created links on WWAN netdev ops unregistering
in the same way that RTNL removes all links on RTNL ops unregistering.
Simply remove all child netdevs of a device whose WWAN netdev ops is
unregistering. This way we protecting the kernel from buggy drivers and
make it easier to write a driver deinitialization code.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use unregister_netdevice_queue() instead of simple
unregister_netdevice() if the WWAN netdev ops does not provide a dellink
callback. This will help to accelerate deletion of multiple netdevs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setup callback will be unconditionally passed to the
alloc_netdev_mqs(), where the NULL pointer dereference will cause the
kernel panic. So refuse to register WWAN netdev ops with warning
generation if the setup callback is not provided.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is unlikely that RTNL callbacks will call WWAN ops (un-)register
functions, but it is highly likely that the ops (un-)register functions
will use RTNL link create/destroy handlers. So move the WWAN network
interface ops (un-)register functions below the RTNL callbacks to be
able to call them without forward declarations.
No functional changes, just code relocation.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for networking interface creation via the WWAN core by
registering the WWAN netdev creation ops for each simulated WWAN device.
Implemented minimalistic netdev support where the xmit callback just
consumes all egress skbs.
This should help with WWAN network interfaces creation testing.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address of &ipc_mux->ul_adb can't be NULL because it points to the
middle of a non-NULL struct.
Fixes: 9413491e20 ("net: iosm: encode or decode datagram")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, the WWAN core provides wwan_port_txon/off() to implement
blocking writes. The tx() port operation should not block, instead
wwan_port_txon/off() should be called when the TX queue is full or has
free space again.
However, in some cases it is not straightforward to make use of that
functionality. For example, the RPMSG API used by rpmsg_wwan_ctrl.c
does not provide any way to be notified when the TX queue has space
again. Instead, it only provides the following operations:
- rpmsg_send(): blocking write (wait until there is space)
- rpmsg_trysend(): non-blocking write (return error if no space)
- rpmsg_poll(): set poll flags depending on TX queue state
Generally that's totally sufficient for implementing a char device,
but it does not fit well to the currently provided WWAN port ops.
Most of the time, using the non-blocking rpmsg_trysend() in the
WWAN tx() port operation works just fine. However, with high-frequent
writes to the char device it is possible to trigger a situation
where this causes issues. For example, consider the following
(somewhat unrealistic) example:
# dd if=/dev/zero bs=1000 of=/dev/wwan0qmi0
dd: error writing '/dev/wwan0qmi0': Resource temporarily unavailable
1+0 records out
This fails immediately after writing the first record. It's likely
only a matter of time until this triggers issues for some real application
(e.g. ModemManager sending a lot of large QMI packets).
The rpmsg_char device does not have this problem, because it uses
rpmsg_trysend() and rpmsg_poll() to support non-blocking operations.
Make it possible to use the same in the RPMSG WWAN driver by adding
two new optional wwan_port_ops:
- tx_blocking(): send data blocking if allowed
- tx_poll(): set additional TX poll flags
This integrates nicely with the RPMSG API and does not require
any change in existing WWAN drivers.
With these changes, the dd example above blocks instead of exiting
with an error.
Cc: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remote processor messaging (rpmsg) subsystem provides an interface
to communicate with other remote processors. On many Qualcomm SoCs this
is used to communicate with an integrated modem DSP that implements most
of the modem functionality and provides high-level protocols like
QMI or AT to allow controlling the modem.
For QMI, most older Qualcomm SoCs (e.g. MSM8916/MSM8974) have
a standalone "DATA5_CNTL" channel that allows exchanging QMI messages.
Note that newer SoCs (e.g. SDM845) only allow exchanging QMI messages
via a shared QRTR channel that is available via a socket API on Linux.
For AT, the "DATA4" channel accepts at least a limited set of AT
commands, on many older and newer Qualcomm SoCs, although QMI is
typically the preferred control protocol.
Often there are additional QMI/AT channels (usually named DATA*_CNTL
for QMI and DATA* for AT), but it is not clear if those are really
functional on all devices. Also, at the moment there is no use case
for having multiple QMI/AT ports. If needed more channels could be
added later after more testing.
Note that the data path (network interface) is entirely separate
from the control path and varies between Qualcomm SoCs, e.g. "IPA"
on newer Qualcomm SoCs or "BAM-DMUX" on some older ones.
The RPMSG WWAN CTRL driver exposes the QMI/AT control ports via the
WWAN subsystem, and therefore allows userspace like ModemManager to
set up the modem. Until now, ModemManager had to use the RPMSG-specific
rpmsg-char where the channels must be explicitly exposed as a char
device first and don't show up directly in sysfs.
The driver is a fairly simple glue layer between WWAN and RPMSG
and is mostly based on the existing mhi_wwan_ctrl.c and rpmsg_char.c.
Cc: Loic Poulain <loic.poulain@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function 'ipc_mmio_get_cp_version' is declared twice, so remove the
repeated declaration and wrong comments.
Cc: M Chetan Kumar <m.chetan.kumar@intel.com>
Cc: Intel Corporation <linuxwwan@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Reviewed-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is not strong reason to have both WWAN and WWAN_CORE symbols,
Let's build the WWAN core framework when WWAN is selected, in the
same way as for other subsystems.
This fixes issue with mhi_net selecting WWAN_CORE without WWAN and
reported by kernel test robot:
Kconfig warnings: (for reference only)
WARNING: unmet direct dependencies detected for WWAN_CORE
Depends on NETDEVICES && WWAN
Selected by
- MHI_NET && NETDEVICES && NET_CORE && MHI_BUS
Fixes: 9a44c1cc63 ("net: Add a WWAN subsystem")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Author forgot to remove that flag.
Fixes: f7af616c63 ("net: iosm: infrastructure")
Reported-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Create net device & implement net operations for data/IP communication.
2) Bind IP Link to mux IP session for simultaneous IP traffic.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Update UL/DL transfer descriptors in message ring.
2) Define message set for pipe/sleep protocol.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Defines messaging protocol for handling Transfer Descriptor
in both UL/DL direction.
2) Ring buffer management.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements state machine to handle host & device sleep.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Encode UL packet into datagram.
2) Decode DL datagram and route it to network layer.
3) Supports credit based flow control.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Establish IP session between host-device & session management.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Bottom half(tasklet) for IRQ and task processing.
2) Tasks are processed asynchronous and synchronously.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements wwan port for MBIM & AT protocol communication
Signed-off-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defines pipes & channel configurations like channel type,
pipe mappings, No. of transfer descriptors and transfer
buffer size etc.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Binds logical channel between host-device for communication.
2) Implements device specific(Char/Net) IO operations.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Initializes shared memory for host-device communication.
2) Allocate resources required for control & data operations.
3) Transfers the Device IRQ to IPC execution thread.
4) Defines the timer cbs for async events.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Initializes the Scratchpad region for Host-Device communication.
2) Exposes device capabilities like chip info and device execution
stages.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Register IOSM driver with kernel to manage Intel WWAN PCIe
device(PCI_VENDOR_ID_INTEL, INTEL_CP_DEVICE_7560_ID).
2) Exposes the EP PCIe device capability to Host PCIe core.
3) Initializes PCIe EP configuration and defines PCIe driver probe, remove
and power management OPS.
4) Allocate and map(dma) skb memory for data communication from device to
kernel and vice versa.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to create (and destroy) interfaces via a new
rtnetlink kind "wwan". The responsible driver has to use
the new wwan_register_ops() to make this possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Purge the rx queue as soon as a user closes the port, just after the
port stop callback invocation. This is to prevent feeding a user that
will open the port next time with outdated and possibly unrelated
data.
While at it also remove the odd skb_queue_purge() call in the port
device destroy callback. The queue will be purged just before the
callback is ivoncated in the wwan_remove_port() function.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not unreasonable to assume that users will use terminal emulation
software to communicate directly with a WWAN device over the AT port.
But terminal emulators will refuse to work with a device that does not
support terminal IOCTLs (e.g. TCGETS, TCSETS, TIOCMSET, etc.). To make
it possible to interact with the WWAN AT port using a terminal emulator,
implement a minimal set of terminal IOCTLs.
The implementation is rather stub, no passed data are actually used to
control a port behaviour. An obtained configuration is kept inside the
port structure and returned back by a request. The latter is done to
fool a program that will test the configuration status by comparing the
readed back data from the device with earlier configured ones.
Tested with fresh versions of minicom and picocom terminal apps.
MBIM, QMI and other ports for binary protocols can hardly be considered
a terminal device, so terminal IOCTLs are only implemented for the AT
port.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is quite common for a userpace program to fetch the buffered amount
of data in the rx queue to avoid the read block. Implement the TIOCINQ
ioctl to make the migration to the WWAN port usage smooth.
Despite the fact that the read call will return no more data than the
size of a first skb in the queue, TIOCINQ returns the entire amount of
buffered data (sum of all queued skbs). This is done to prevent the
breaking of programs that optimize reading, avoiding it if the buffered
amount of data is too small.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we limit the total ports number to 256. It is quite common
for PBX or SMS gateway to be equipped with a lot of modems. In now days,
a modem could have 2-4 control ports or even more, what only accelerates
the ports exhausing rate.
To avoid facing the port number limitation issue reports, increase the
limit up the maximum number of minors (i.e. up to 1 << MINORBITS).
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, the port name is allocated based on the parent device
name, port id and the port type. Where the port id specifies nothing but
the ports registration order and is only used to make the port name
unique.
Most likely, to configure a WWAN device, the user will look for a port
of a specific type (e.g. AT port or MBIM port, etc.). The current naming
scheme can make it difficult to find a port of a specific type.
Consider a WWAN device that has 3 ports: AT port, MBIM port, and another
one AT port. With the global port index, the port names will be:
* wwan0p1at
* wwan0p2mbim
* wwan0p3at
To find the MBIM port, user should know in advance the device ports
composition (i.e. the user should know that the MBIM port is the 2nd
one) or carefully examine the whole ports list. It is not unusual for
USB modems to have a different composition, even if they are build on a
same chipset. Moreover, some modems able to change the ports composition
based on the user's configuration. All this makes port names fully
unpredictable.
To make naming more user-friendly, remove the global port id and
enumerate ports by its type. E.g.:
* wwan0p1at -> wwan0at0
* wwan0p2mbim -> wwan0mbim0
* wwan0p3at -> wwan0at1
With this naming scheme, the first AT port name will always be wwanXat0,
the first MBIM port name will always be wwanXmbim0, etc.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usually a device name is spelled in lowercase, let us follow this
practice in the WWAN subsystem as well. The bottom line is that such
name is easier to type.
To keep the device type attribute contents more natural (i.e., spell
abbreviations in uppercase), while making the device name lowercase,
turn the port type strings array to an array of structure that contains
both the port type name and the device name suffix.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This array is indexed by port type. Make it self-descriptive by using
the port type enum values as indices in the array initializer.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is quite unusual when some value can not be equal to a defined range
max value. Also most subsystems defines FOO_TYPE_MAX as a maximum valid
value. So turn the WAN_PORT_MAX meaning from the number of supported
port types to the maximum valid port type.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
wwan_hwsim creates and removes simulated control ports on module loading
and unloading. It would be helpful to be able to create/remove devices
and ports at run-time to trigger wwan port (un-)register actions without
module reloading.
Some simulator objects (e.g. ports) do not have the underling device and
it is not possible to fully manage the simulator via sysfs. wwan_hsim
intend for developers, so implement it as a self-contained debugfs based
management interface.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver simulates a set of WWAN device with a set of AT control
ports. It can be used to test WWAN kernel framework as well as user
space tools.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add index sysfs attribute for WWAN devices. This index is used to
uniquely indentify and reference a WWAN device. 'index' is the
attribute name that other device classes use (wireless, v4l2-dev,
rfkill, etc...).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port type is by default part of the WWAN port device name.
However device name can not be considered as a 'stable' API and
may be subject to change in the future. This change adds a proper
device attribute that can be used to determine the WWAN protocol/
type.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that the poll system call returns proper error flags when port
is removed (nullified port ops), allowing user side to properly fail,
without further read or write.
Fixes: 9a44c1cc63 ("net: Add a WWAN subsystem")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mhi_wwan_rx_budget_dec function is supposed to return true if
RX buffer budget has been successfully decremented, allowing to queue
a new RX buffer for transfer. However the current implementation is
broken when RX budget is '1', in which case budget is decremented but
false is returned, preventing to requeue one buffer, and leading to
RX buffer starvation.
Fixes: fa588eba63 ("net: Add Qcom WWAN control driver")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bit operation helpers such as test_bit, clear_bit, etc take bit
position as parameter and not value. Current usage causes double
shift => BIT(BIT(0)). Fix that in wwan_core and mhi_wwan_ctrl.
Fixes: 9a44c1cc63 ("net: Add a WWAN subsystem")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MHI WWWAN control driver allows MHI QCOM-based modems to expose
different modem control protocols/ports via the WWAN framework, so that
userspace modem tools or daemon (e.g. ModemManager) can control WWAN
config and state (APN config, SMS, provider selection...). A QCOM-based
modem can expose one or several of the following protocols:
- AT: Well known AT commands interactive protocol (microcom, minicom...)
- MBIM: Mobile Broadband Interface Model (libmbim, mbimcli)
- QMI: QCOM MSM/Modem Interface (libqmi, qmicli)
- QCDM: QCOM Modem diagnostic interface (libqcdm)
- FIREHOSE: XML-based protocol for Modem firmware management
(qmi-firmware-update)
Note that this patch is mostly a rework of the earlier MHI UCI
tentative that was a generic interface for accessing MHI bus from
userspace. As suggested, this new version is WWAN specific and is
dedicated to only expose channels used for controlling a modem, and
for which related opensource userpace support exist.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change introduces initial support for a WWAN framework. Given the
complexity and heterogeneity of existing WWAN hardwares and interfaces,
there is no strict definition of what a WWAN device is and how it should
be represented. It's often a collection of multiple devices that perform
the global WWAN feature (netdev, tty, chardev, etc).
One usual way to expose modem controls and configuration is via high
level protocols such as the well known AT command protocol, MBIM or
QMI. The USB modems started to expose them as character devices, and
user daemons such as ModemManager learnt to use them.
This initial version adds the concept of WWAN port, which is a logical
pipe to a modem control protocol. The protocols are rawly exposed to
user via character device, allowing straigthforward support in existing
tools (ModemManager, ofono...). The WWAN core takes care of the generic
part, including character device management, and relies on port driver
operations to receive/submit protocol data.
Since the different devices exposing protocols for a same WWAN hardware
do not necessarily know about each others (e.g. two different USB
interfaces, PCI/MHI channel devices...) and can be created/removed in
different orders, the WWAN core ensures that all WAN ports contributing
to the 'whole' WWAN feature are grouped under the same virtual WWAN
device, relying on the provided parent device (e.g. mhi controller,
USB device). It's a 'trick' I copied from Johannes's earlier WWAN
subsystem proposal.
This initial version is purposely minimalist, it's essentially moving
the generic part of the previously proposed mhi_wwan_ctrl driver inside
a common WWAN framework, but the implementation is open and flexible
enough to allow extension for further drivers.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
