The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).
Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.
Fixes: 9dab1868ec ("pinctrl: amlogic: Make driver independent from two-domain configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).
Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.
Fixes: 9dab1868ec ("pinctrl: amlogic: Make driver independent from two-domain configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We just changed the code so we apply bias disable on the correct
register but forgot to align the register calculation. The result
is that we apply the change on the correct register, but possibly
at the incorrect offset/bit
This went undetected because offsets tends to be the same between
REG_PULL and REG_PULLEN for a given pin the EE controller. This
is not true for the AO controller.
Fixes: e39f9dd820 ("pinctrl: meson: fix pinconf bias disable")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOX tsin_a pins wrongly uses the SDCard pinctrl bits, this
patch completely removes these pins entries until we find out what
are the correct bits and registers to be used instead.
Fixes: 5a6ae9b801 ("pinctrl: meson-gxl: add tsin_a pins")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AO pull register definition is inverted between pull (up/down) and
pull enable. Fixing this allows to properly apply bias setting
through pinconf
Fixes: 0fefcb6876 ("pinctrl: Add support for Meson8b")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AO pull register definition is inverted between pull (up/down) and
pull enable. Fixing this allows to properly apply bias setting
through pinconf
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AO pull register definition is inverted between pull (up/down) and
pull enable. Fixing this allows to properly apply bias setting
through pinconf
Fixes: 468c234f9e ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a bias is enabled on a pin of an Amlogic SoC, calling .pin_config_set()
with PIN_CONFIG_BIAS_DISABLE will not disable the bias. Instead it will
force a pull-down bias on the pin.
Instead of the pull type register bank, the driver should access the pull
enable register bank.
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These drivers are GPIO drivers, and the do not need to use the
legacy header in <linux/gpio.h>, go directly for
<linux/gpio/driver.h> instead.
Replace any use of GPIOF_* with 0/1, these flags are for
consumers, not drivers.
Get rid of a few gpio_to_irq() users that was littering
around the place, use local callbacks or avoid using it at
all.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pinctrl driver for Meson-G12A SoC which share the similar IP as
the previous Meson-AXG SoC, both use same pinmux ops (register layout).
A new driver is needed here due to the differences in the pins.
Starting from Meson-AXG SoC, the pinctrl controller block use 4
continues register bits to specific the pin mux function, while comparing
to old generation SoC which using variable length register bits for
the pin mux definition. The new design greatly simplify the software model.
For the detail example, one 32bit register can be divided into 8 parts,
each has 4 bits whose value start from 0 - 7, each can describe one pin,
the value 0 is always devoted to GPIO function, while 1 - 7 devoted to
the mux pin function.
Please note, the GPIOE is actually located at AO (always on) bank.
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pinctrl configuration for gen_clk on gxbb and axg.
gen_clk allows to output and devide several internal clocks of SoC,
including most of the plls.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No core changes this time! Just a calm all-over-the-place
drivers, updates and fixes cycle as it seems.
New drivers/subdrivers:
- Actions Semiconductor S900 driver with more Actions
variants for S700, S500 in the pipe. Also generic GPIO
support on top of the same driver and IRQ support is in
the pipe.
- Renesas r8a77470 PFC support.
- Renesas r8a77990 PFC support.
- Allwinner Sunxi H6 R_PIO support.
- Rockchip PX30 support.
- Meson Meson8m2 support.
- Remove support for the ill-fated Samsung Exynos 5440 SoC.
Improvements:
- Context save/restore support in pinctrl-single.
- External interrupt support for the Mediatek MT7622.
- Qualcomm ACPI HID QCOM8002 supported.
Fixes:
- Fix up suspend/resume support for Exynos 5433.
- Fix Strago DMI fixes on the Intel Cherryview.
-----BEGIN PGP SIGNATURE-----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=6On2
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for v4.18.
No core changes this time! Just a calm all-over-the-place drivers,
updates and fixes cycle as it seems.
New drivers/subdrivers:
- Actions Semiconductor S900 driver with more Actions variants for
S700, S500 in the pipe. Also generic GPIO support on top of the
same driver and IRQ support is in the pipe.
- Renesas r8a77470 PFC support.
- Renesas r8a77990 PFC support.
- Allwinner Sunxi H6 R_PIO support.
- Rockchip PX30 support.
- Meson Meson8m2 support.
- Remove support for the ill-fated Samsung Exynos 5440 SoC.
Improvements:
- Context save/restore support in pinctrl-single.
- External interrupt support for the Mediatek MT7622.
- Qualcomm ACPI HID QCOM8002 supported.
Fixes:
- Fix up suspend/resume support for Exynos 5433.
- Fix Strago DMI fixes on the Intel Cherryview"
* tag 'pinctrl-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: cherryview: limit Strago DMI workarounds to version 1.0
pinctrl: at91-pio4: add missing of_node_put
pinctrl: armada-37xx: Fix spurious irq management
gpiolib: discourage gpiochip_add_pin[group]_range for DT pinctrls
pinctrl: msm: fix gpio-hog related boot issues
MAINTAINERS: update entry for Mediatek pin controller
pinctrl: mediatek: remove unused fields in struct mtk_eint_hw
pinctrl: mediatek: use generic EINT register maps for each SoC
pinctrl: mediatek: add EINT support to MT7622 SoC
pinctrl: mediatek: refactor EINT related code for all MediaTek pinctrl can fit
dt-bindings: pinctrl: add external interrupt support to MT7622 pinctrl
pinctrl: freescale: Switch to SPDX identifier
pinctrl: samsung: Fix suspend/resume for Exynos5433 GPF1..5 banks
pinctrl: sh-pfc: rcar-gen3: Fix grammar in static pin comments
pinctrl: sh-pfc: r8a77965: Add I2C pin support
pinctrl: sh-pfc: r8a77990: Add EthernetAVB pins, groups and functions
pinctrl: sh-pfc: r8a77990: Add I2C{1,2,4,5,6,7} pins, groups and functions
pinctrl: sh-pfc: r8a77990: Add SCIF pins, groups and functions
pinctrl: sh-pfc: r8a77990: Add bias pinconf support
pinctrl: sh-pfc: Initial R8A77990 PFC support
...
The data pin 0-7 of the NAND controller are actually missing from
the nand pinctrl group, so we fix it here.
Fixes: 0f15f500ff ("pinctrl: meson: Add GXL pinctrl definitions")
Reported-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The data pin 0-7 of the NAND controller are actually missing from
the nand pinctrl group, so we fix it here.
Fixes: cd1e3b01c7 ("pinctrl: amlogic: gxbb: add nand pins")
Reported-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the information related to the tdm pins of the A113D SoC
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These are only available on the Meson8m2 SoC (which uses the same
DesignWare Ethernet MAC as Meson8b).
The "eth_tx_clk_50m" signal either provides a 50MHz clock for the RMII
PHYs or the RGMII TX clock (as far as we know the frequency is
controlled by the PRG_ETHERNET registers in the Ethernet MAC "glue" IP
block).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add Meson8m2 support to the existing Meson8 pinctrl driver. Since there
are only very few changes (Meson8m2 has an extra signal on 10 CBUS pins,
no other differences were found so far).
Add the new compatible strings for Meson8m2 to the existing Meson8
driver so we don't have to duplicate the whole driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOAO bank is range from GPIOAO_0 to GPIOAO_13.
Fixes: 83c566806a ("pinctrl: meson-axg: Add new pinctrl driver for Meson AXG SoC")
Reported-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New drivers:
- Qualcomm SDM845: this is their new flagship SoC platform
which seems to be targeted at premium mobile handsets.
- Renesas R-Car M3-N SoC.
- Renesas R8A77980 SoC.
- NXP (ex Freescale) i.MX 6SLL SoC.
- Mediatek MT2712 SoC.
- Allwinner H6 SoC.
Improvements:
- Uniphier adds a few new functions and pins.
- Renesas refactorings and additional pin definitions.
- Improved pin groups for Axis Artpec6.
Cleanup:
- Drop the TZ1090 drivers. This platform is no longer
maintained and is being deleted.
- Drop ST-Ericsson U8540/U9540 support as this was never
productified.
- Overall minor fixes and janitorial.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJawz1oAAoJEEEQszewGV1zWUUQAJEIXW0vEsgwwFCIQYrKZBbi
ovfQtpPgv5wbRmvLy/IaIFvO7eFedlOqjLTU0a3wuFZdHn9y0VkebVOjdG97TTeF
g4fyqQ7pzdCKmxlDMm4zcOUycho9ZMa8lG3tKdyxI4tal6ygl81BypzKVi/WIxLA
po2Vr1MHfKicWyPbgD1VRJV6oSzXSOMFkEcPUqx+6m5OM/GTKTKasU/fa4uu12jI
OHF1TVr9glMbPiU0wC8bvKilgXCxhDYMYf1JCaxojr0Rt/DlR2vBgbfU7dIeRtO1
MJ1nyJm0yZQfN/bBV1roSg/GGRS3jGbdHDzMnK8pI6LJNJYRa6vfLD/NHKUciSnf
5cgpWloyvR+rbfObr6CYTirKE7iGBYvAH+do2TwmfvfwUYOI9lnbJrtnqtIovdVA
R5FxrvI/Ol/j2t4V5wZGC1BBDsC6GH/1YV+W+n9fwKMdDIRgEsOTFsCNEWmSShWP
Z53NzyZRVL32RK35g3WEqicfXOtmw3XXuHJZqWjlmXyVitEElMAVWySd6oG0HhvU
sdRaoVGjXL9EVM3iZrqHtaRazRjItBA2CFnloC1PVjwi+dkHDcwWDvtOur+AF3wz
VORi0xlWXd0Gzolo/ccsk7JUVmrkfCDnZx9uiTKQ+jgiSDfoEuQOvBfTI6LdeoNY
upTZIfEhR/dMcjcdKIKe
=IT6S
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control bulk updates from Linus Walleij:
"New drivers:
- Qualcomm SDM845: this is their new flagship SoC platform which
seems to be targeted at premium mobile handsets.
- Renesas R-Car M3-N SoC.
- Renesas R8A77980 SoC.
- NXP (ex Freescale) i.MX 6SLL SoC.
- Mediatek MT2712 SoC.
- Allwinner H6 SoC.
Improvements:
- Uniphier adds a few new functions and pins.
- Renesas refactorings and additional pin definitions.
- Improved pin groups for Axis Artpec6.
Cleanup:
- Drop the TZ1090 drivers. This platform is no longer maintained and
is being deleted.
- Drop ST-Ericsson U8540/U9540 support as this was never
productified.
- Overall minor fixes and janitorial"
* tag 'pinctrl-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: uniphier: add UART hardware flow control pin-mux settings
pinctrl: sunxi: add support for the Allwinner H6 main pin controller
pinctrl: sunxi: change irq_bank_base to irq_bank_map
pinctrl: sunxi: introduce IRQ bank conversion function
pinctrl: sunxi: refactor irq related register function to have desc
pinctrl: msm8998: Remove owner assignment from platform_driver
pinctrl: uniphier: divide I2S and S/PDIF audio out pin-mux group
pinctrl: uniphier: add PXs2 Audio in/out pin-mux settings
pinctrl/amd: poll InterruptEnable bits in enable_irq
pinctrl: ocelot: fix gpio direction
pinctrl: mtk: fix check warnings.
pintcrl: mtk: support bias-disable of generic and special pins simultaneously
pinctrl: add mt2712 pinctrl driver
pinctrl: pinctrl-single: Fix pcs_request_gpio() when bits_per_mux != 0
pinctrl: imx: Add pinctrl driver support for imx6sll
dt-bindings: imx: update pinctrl doc for imx6sll
pinctrl: intel: Implement intel_gpio_get_direction callback
pinctrl: stm32: add 'depends on HAS_IOMEM' to fix unmet dependency
pinctrl: mediatek: mtk-common: use true and false for boolean values
pinctrl: sunxi: always look for apb block
...
Meson8b is a cost reduced variant of the Meson8 SoC. It's package size
is smaller than Meson8.
Unfortunately there are a few key differences which cannot be seen
without close inspection of the code and the public S805 datasheet:
- the GPIOX bank is missing the GPIOX_12, GPIOX_13, GPIOX_14 and
GPIOX_15 GPIOs
- the GPIOY bank is missing the GPIOY_2, GPIOY_4, GPIOY_5, GPIOY_15 and
GPIOY_16 GPIOs
- the GPIODV bank is missing all GPIOs except GPIODV_9, GPIODV_24,
GPIODV_25, GPIODV_26, GPIODV_27, GPIODV_28 and GPIODV_29
- the GPIOZ bank is missing completely
- there is a new GPIO bank called "DIF"
This means that Meson8b only has 83 actual GPIO lines. Without any holes
there would be 130 GPIO lines in total (120 are inherited from Meson8
plus 10 new from the DIF bank).
GPIOs greater GPIOZ_3 (whose ID is 83 - as a reminder: this is exactly
the number of actual GPIO lines on Meson8b and also the value of
meson8b_cbus_pinctrl_data.num_pins) cannot berequested. Using CARD_6
(which used ID 100 prior to this patch, "base of the GPIO controller was
382) as an example:
$ echo 482 > /sys/class/gpio/export
export_store: invalid GPIO 482
This removes all non-existing pins from to dt-bindings header file
(include/dt-bindings/gpio/meson8b-gpio.h). This allows us to have a
consecutive numbering for the GPIO #defines (GPIOY_2 doesn't exist for
example, so previously the GPIOY_3 ID was "GPIOY_1 + 2", after this
patch it is "GPIOY_1 + 1"). As a nice side-effect this means that we get
compile-time (instead of runtime) errors if Meson8b .dts uses a pin that
only exists on Meson8.
Additionally the pinctrl-meson8b driver has to be updated to handle this
new GPIO numbering. By default a struct meson_bank only handles GPIO
banks where the pins are numbered consecutively because it calculates
the bit offsets based on the GPIO IDs.
This is solved by taking the original BANK() definition and splitting it
into consecutive subsets (X0..11 and X16..21). The bit offsets for each
new bank includes the skipped GPIOs (the definition of the "X0..11" bank
is identical to the old "X" bank apart from the "last IRQ" field, the
definition of the new, split "X16..21" bank takes the original "X" bank
and adds 16 - the start of the new split bank - to the "first IRQ",
pullen bit, pull bit, dir bit, out bit and in bit).
Commit 984cffdeae ("pinctrl: Fix gpio/pin mapping for Meson8b")
fixed the same issue by setting "ngpio" (of the gpio_chip) to 130.
Unfortunately this broke in db80f0e158 ("pinctrl: meson: get rid of
unneeded domain structures").
The solution from this patch was considered to be better than the
previous attempt at fixing this because it provides compile-time error
checking for the GPIOs that exist on Meson8 but don't exist on Meson8b.
The following pins were tested on an Odroid-C1 using the sysfs GPIO
interface checking that their value (high or low) could be read:
- GPIOX_0, GPIOX_1, GPIOX_2, GPIOX_3, GPIOX_4, GPIOX_5, GPIOX_6,
GPIOX_7, GPIOX_8, GPIOX_9, GPIOX_10, GPIOX_11, GPIOX_18, GPIOX_19,
GPIOX_20, GPIOX_21
- GPIOY_3, GPIOY_7, GPIOY_8
(some of these had to be pulled up because they were low by default,
others were high by default so these had to be pulled down)
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simply adjust the pin group to _x _y _z style, as to
keep the consistency in DT with previous naming scheme.
Fixes: 83c566806a ("pinctrl: meson-axg: Add new pinctrl driver for Meson AXG SoC")
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to datasheet, we should use numbers for the pin naming
instead of letters. The patch here try to fix this to keep
the consistency.
This patch should not bring any functional change.
Fixes: 83c566806a ("pinctrl: meson-axg: Add new pinctrl driver for Meson AXG SoC")
Suggested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin controller has been updated in the Amlogic Meson AXG series,
which use continuous 4-bit register to select function for each pin.
In order to support this, a new pinmux operations "meson_axg_pmx_ops"
has been added.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change prepare the introduction of new meson SoC. This new SoC will
share the same gpio/pinconf registers but the pinmux part will be
different. While the format of the data associated with each pinmux group
will change, the way to handle pinmuxing will be similar.
To deal with this new situation, the meson_pmx_struture is kept but the
data associated to it is now generic. This allows to reuse the basic
functions which would otherwise be copy/pasted in each pinmux driver
(such as getting the name a count of groups and functions) Only the
functions actually using this specific data is taken out of the common
code and is handling the SoC pinmuxing
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When meson pinctrl is enabled, all meson platforms pinctrl drivers are
built in the kernel, with a significant amount of data.
This leads to situation where pinctrl drivers targeting an architecture
are also compiled and shipped on another one (ex: meson8 - ARM - compiled
and shipped on ARM64 builds). This is a waste of memory we can easily
avoid.
This change makes 4 pinctrl drivers (1 per SoC) out the original single
driver, allowing to compile and ship only the ones required.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While removing the need to have pin_base defined in meson pinctrl
drivers, I forgot to remove the corresponding field from the
pinctrl_data structure.
Fixing this now.
Fixes: 70e5ecb1b9 ("pinctrl: meson: get rid of pin_base")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add TEST_N pinmux for channel 6 and 7 of the i2s output
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIOX_22 is declared as a gpio but the id is no present in the pin
table. This hole trigger an error while reading the pingroup debugfs entry
GPIOX_22 is no routed externally. For all we know, it could an internal
pin of SoC
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On meson-gx platforms, TEST_N has been incorrectly declared in the EE
controller while it belongs to AO controller.
Move the pin to the appropriate controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pin_base was used with the manually set pin offset in meson pinctrl. This
is no longer the case, pin_base is 0 on every meson pinctrl controllers
and should go away.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Offset on meson pinctrl and gpios is something that was carried from the
vendor driver, where there is a weird link between the 2
controllers. Since these 2 controllers are independent, this offset adds
an unnecessary complexity.
This patch remove this manually set offset and rely on pinctrl to figure
out the gpio base offset
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ENOSYS is special and should only be used for incorrect syscall number.
It is not the case here. let's use ENOTSUPP instead.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add Tsin A pins to bank DV and X.
We don't have a driver for the tsin yet but since the tsin A pinmux is
enabled by default at boot time, declaring this pinmux is required to
properly operate on GPIOX.
Without this change, GPIOX 8, 9, 10 and 11 can't be driven as GPIO output
as the tsin A seems to have priority.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add GPIO interrupt information to pinctrl data. Added to the original
version from Jerome was data for Meson GXL.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After commit 34e61801a3 "pinctrl: meson-gxbb: Add missing GPIODV_18
pin entry" I started to get the following warning:
"meson-pinctrl c8834000.periphs:pinctrl@4b0: names 119 do not match
number of GPIOs 120"
It turned out that not the mentioned commit has a problem, it just
revealed another problem which had existed before.
There is no PIN GPIOX_22 on Meson GXBB.
Fixes: 468c234f9e ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Amlogic Meson GXL SoCs embeds an 10/100 Ethernet PHY, this patchs enables
the Link and Activity LEDs signals.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the AO and EE domain CEC pins for the Amlogic Meson GXL SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the AO and EE domain CEC pins for the Amlogic Meson GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AO SPDIF pins were incorrectly defined with the EE pin offset.
Fixes: b840d649f9 ("pinctrl: meson: gxl: add spdif output pins")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AO I2S pins were incorrectly defined with the EE pin offset.
Fixes: 2899adf042 ("pinctrl: meson: gxl: add i2s output pins")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIODV_18 entry was missing in the original driver push.
Fixes: 468c234f9e ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPICC controller has dedicated SPI pins, this patchs add the pins
definition in the GXBB pinctrl driver
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPICC controller has dedicated SPI pins, this patchs add the pins
definition in the GXL pinctrl driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds another missing pin found in the Meson8 SoCs. Currently
there's no driver which would use this pin yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds another missing pin found in the Meson8 SoCs. Currently
there's no driver which would use this pin yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the I2S and SPDIF input and output pins, similar
to what we have on GXBB and GXL.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the missing pins for the PWM controllers found in Amlogic
Meson8 SoCs. This includes the pins for PWM_A, PWM_B, PWM_C, PWM_D,
PWM_E and PWM_F controllers.
There is an additional PWM function with the name PWM_VS in the vendor
kernel sources which seems to be used for external video input. Thus
it's not part of this change as the IP block behind the pwm-meson driver
is not responsible for these pins.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Add bi-directional and output-enable pin configurations to
the generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- A whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- Switch meson driver to get the GPIO ranges from the device
tree.
- Input schmitt trigger support on the Rockchip driver.
- Enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- Name the Qualcomm QDF2xxx GPIO lines.
- Support GMMR GPIO regions on the Intel Cherryview. This
fixes a serialization problem on these platforms.
- Pad retention support for the Samsung Exynos 5433.
- Handle suspend-to-ram in the AT91-pio4 driver.
- Pin configuration support in the Aspeed driver.
Cleanups:
- The final name of Rockchip RK1108 was RV1108 so rename the
driver and variables to stay consistent.
-----BEGIN PGP SIGNATURE-----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=BCaA
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.12 cycle.
The extra week before the merge window actually resulted in some of
the type of fixes that usually arrive after the merge window already
starting to trickle in from eager developers using -next, I'm
impressed.
I have recruited a Samsung subsubsystem maintainer (Krzysztof) to deal
with the onset of Samsung patches. It works great.
Apart from that it is a boring round, just incremental updates and
fixes all over the place, no serious core changes or anything exciting
like that. The most pleasing to see is Julia Cartwrights work to audit
the irqchip-providing drivers for realtime locking compliance. It's
one of those "I should really get around to looking into that" things
that have been on my TODO list since forever.
Summary:
Core changes:
- add bi-directional and output-enable pin configurations to the
generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- a whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- switch meson driver to get the GPIO ranges from the device tree.
- input schmitt trigger support on the Rockchip driver.
- enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- name the Qualcomm QDF2xxx GPIO lines.
- support GMMR GPIO regions on the Intel Cherryview. This fixes a
serialization problem on these platforms.
- pad retention support for the Samsung Exynos 5433.
- handle suspend-to-ram in the AT91-pio4 driver.
- pin configuration support in the Aspeed driver.
Cleanups:
- the final name of Rockchip RK1108 was RV1108 so rename the driver
and variables to stay consistent"
* tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits)
pinctrl: mediatek: Add missing pinctrl bindings for mt7623
pinctrl: artpec6: Fix return value check in artpec6_pmx_probe()
pinctrl: artpec6: Remove .owner field for driver
pinctrl: tegra: xusb: Silence sparse warnings
ARM: at91/at91-pinctrl documentation: fix spelling mistake: "contoller" -> "controller"
pinctrl: make artpec6 explicitly non-modular
pinctrl: aspeed: g5: Add pinconf support
pinctrl: aspeed: g4: Add pinconf support
pinctrl: aspeed: Add core pinconf support
pinctrl: aspeed: Document pinconf in devicetree bindings
pinctrl: Add st,stm32f469-pinctrl compatible to stm32-pinctrl
pinctrl: stm32: Add STM32F469 MCU support
Documentation: dt: Remove ngpios from stm32-pinctrl binding
pinctrl: stm32: replace device_initcall() with arch_initcall()
pinctrl: stm32: add possibility to use gpio-ranges to declare bank range
pinctrl: armada-37xx: Add gpio support
pinctrl: armada-37xx: Add pin controller support for Armada 37xx
pinctrl: dt-bindings: Add documentation for Armada 37xx pin controllers
pinctrl: core: Make pinctrl_init_controller() static
pinctrl: generic: Add bi-directional and output-enable
...
The NAND DQS pins are currently named nand_dqs_0 and nand_dqs_1.
However, they both seem to have the same function, just exposed on
different pins (unlike the ethernet TX pins for example, where there's
eth_txd0..3 - all of these can be active at the same time as they are
different data lines).
Rename the NAND DQS pins to nand_dqs_15 and nand_dqs_18 to reflect that
it's the same functionality just exposed on different pins (BOOT_15 and
BOOT_18).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The nand_groups table uses different names for the NAND DQS pins than
the GROUP() definition in meson8b_cbus_groups (nand_dqs_0 vs nand_dqs0).
This prevents using the NAND DQS pins in the devicetree.
Fix this by ensuring that the GROUP() definition and the
meson8b_cbus_groups use the same name for these pins.
Fixes: 0fefcb6876 ("pinctrl: Add support for Meson8b")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When trying to add a gpio-hog, we enter a weird loop where the gpio-ranges
is needed when gpiochip_add_data() is called but in the current implementation
the ranges are added from the driver afterwards.
A simple solution is to rely on the DR gpio-ranges attribute and remove the
call to gpiochip_add_pin_range().
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix some inverted bit numbers in some pinctrl groups and add missing pins
and groups to be in pair with the GXBB pinctrl pins definition.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the missing PWM pins on Meson GXL SoCs, namely:
- PWM_A
- PWM_B
- PWM_C
- PWM_F (GPIOX_7 and GPIOCLK_1 can be selected as output)
- PWM_AO_A (GPIOAO_3 and GPIOAO_8 can be selected as output)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the pwm_ao_b pin. Unfortunately the registers for
the pwm_ao pins are not documented at all. The source for the pwm_ao_b
pin from this patch is the Khadas VIM GPL kernel source, which sets bit
3 and unsets bits 4 and 31 to enable the PWM LEDs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current pinconf packed format allows only 16-bit argument limiting
the maximum value 65535. For most types this is enough. However,
debounce time can be in range of hundreths of milliseconds in case of
mechanical switches so we cannot represent the worst case using the
current format.
In order to support larger values change the packed format so that the
lower 8 bits are used as type which leaves 24 bits for the argument.
This allows representing values up to 16777215 and debounce times up to
16 seconds.
We also convert the existing users to use 32-bit integer when extracting
argument from the packed configuration value.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GXBB and GXL/GXM pinctrl drivers had a configuration which conflicts
with uart_ao_a. According to the GXBB ("S905") datasheet the AO UART
functions are:
- GPIOAO_0: Func1 = UART_TX_AO_A (bit 12), Func2 = UART_TX_AO_B (bit 26)
- GPIOAO_1: Func1 = UART_RX_AO_A (bit 11), Func2 = UART_RX_AO_B (bit 25)
- GPIOAO_4: Func2 = UART_TX_AO_B (bit 24)
- GPIOAO_5: Func2 = UART_RX_AO_B (bit 25)
The existing definition for uart_AO_A already uses GPIOAO_0 and GPIOAO_1.
The old definition of uart_AO_B however was broken, as it used GPIOAO_0
for TX (which would be fine) and two pins (GPIOAO_1 and GPIOAO_5) for RX
(which does not make any sense).
This fixes the uart_AO_B configuration by moving it to GPIOAO_4 and
GPIOAO_5 (it would be possible to use GPIOAO_0 and GPIOAO_1 in theory,
but all existing hardware uses uart_AO_A there).
The fix for GXBB and GXL/GXM is identical since it seems that these
specific pins are identical on both SoC variants.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl functions for HDMI HPD pin and DDC pins on Amlogic Meson
GXL and GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl_gpio_request is called with the "full" gpio number, already
containing the base, then meson_pmx_request_gpio is then called with the
final pin number.
Remove the base addition when calling meson_pmx_disable_other_groups.
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
CC: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the Amlogic Meson GXL SoC, this is a partially complete
definition only based on the Amlogic Vendor tree.
This definition differs a lot from the GXBB and needs a separate entry.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add EE domains pins for the NAND flash controller.
Even tough we have no driver for the NAND flash controller yet, we need
to have these pins in pinctrl as the actual pin are shared with the spifc
controller. The bootloader on the S905-P200 setup pinmux for the NAND
controller so we need the kernel to properly deactivate this if necessary.
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the SDIO interrupt pin which can be used by sd_emmc_a.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Fixes: 29885a6565 ("pinctrl: meson-gxbb: add the pins for the
SDIO/sd_emmc_a controller")
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sd_emmc_a is used a controller for the SDIO modules. This adds the pin
configuration for the SDIO controller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for PWM pins, for EE and AO domains.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the IR remote receiver to the AO domain devices.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver originally supported more domains (register ranges) per
pinctrl device, but since commit 9dab1868ec ("pinctrl: amlogic: Make
driver independent from two-domain configuration") each device gets
assigned a single domain and we instantiate multiple pinctrl devices
in the DT.
Therefore, now the 'meson_domain' and 'meson_domain_data' structures
don't have any reason to exist and can be removed to make the model
simpler to understand. This commit doesn't change behavior.
Tested on a Odroid-C2.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's not necessary to unregister pin controller device registered
with devm_pinctrl_register() and using pinctrl_unregister() leads
to a double free.
This is detected by Coccinelle semantic patch.
Fixes: e649f7ec8c ("pinctrl: meson: Use devm_pinctrl_register() for pinctrl registration")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add EE domain pins for ethernet interface.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add EE domain pins for UART A, B & C.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add EE domain pins for eMMC and SD card.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pins for some more AO domain devices: UART_AO_B and I2C master &
slave.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix pinctrl eth_tx_en bit index according to Hardkernel ODROID-C1 datasheet.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the basic platform file to support the pin controller
found on the Amlogic Meson GXBB SoCs.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_pinctrl_register() for pin control registration.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Carlo Caione <carlo@endlessm.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename pinctrl_utils_dt_free_map to pinctrl_utils_free_map, since
it does not depend on device tree despite the current name. This
will enforce a consistent naming in pinctr-utils.c and will make
it clear it can be called from outside device tree (e.g. from
ACPI handling code).
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the Amlogic Meson8 / Meson8b platforms we have two different buses:
cbus and aobus, corresponding to 2 different power domains (regular and
always-on). On each bus a different set of registers is mapped to manage
muxes, GPIOs and in general to control a clear subset of the pins.
Considering this architecture, having two different pinctrl devices, one
for each bus / power domain, makes much more sense than just having one
single device.
Right now we have one single pin controller driver that uses two
different domains (represented by 'gpio' and 'gpio-ao' sub-nodes in the
DTS) to manage the set of registers on the two buses. This dual-domain
configuration is hardcoded into the driver that strictly requires one
domain for each bus in the same pin controller device.
With this patch we refactor the driver to allow splitting the driver in
two parts. This change is needed to have a proper description of the HW
in the device-tree where we want to introduce aobus and cbus.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Separate functions for pins controlled by different pin controllers.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/Kconfig:config PINCTRL_MESON
drivers/pinctrl/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We don't replace module.h with init.h since the file already has that.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Carlo Caione <carlo@endlessm.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Carlo Caione <carlo@endlessm.com>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Core functionality:
- Enable exclusive pin ownership: it is possible to flag a pin
controller so that GPIO and other functions cannot use a single
pin simultaneously.
- New drivers:
- NXP LPC18xx System Control Unit pin controller
- Imagination Pistachio SoC pin controller
- New subdrivers:
- Freescale i.MX7d SoC
- Intel Sunrisepoint-H PCH
- Renesas PFC R8A7793
- Renesas PFC R8A7794
- Mediatek MT6397, MT8127
- SiRF Atlas 7
- Allwinner A33
- Qualcomm MSM8660
- Marvell Armada 395
- Rockchip RK3368
- Cleanups:
- A big cleanup of the Marvell MVEBU driver rectifying it to
correspond to reality
- Drop platform device probing from the SH PFC driver, we are now a
DT only shop for SuperH
- Drop obsolte multi-platform check for SH PFC
- Various janitorial: constification, grammar etc
- Improvements:
- The AT91 GPIO portions now supports the set_multiple() feature
- Split out SPI pins on the Xilinx Zynq
- Support DTs without specific function nodes in the i.MX driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVin37AAoJEEEQszewGV1zIlQP/i6+C47z3OV67hYAOmlGoynl
wsdTFbyp+GIPl3N1r0lRzxOfQsuc9t93iDMrC5ssN9VFaj8MgH/j3XKWf5A55iVn
u7nNQzIFjzTwl58/Pu4oM+d9l5i26o44teFKh3xI4aup4AFed3+lDkQtRipgo29c
V4y+6SaQxQ46e2qaOAM20gEagm2a8EvChn1Zo/HLQnnmZcKBxgObJna7iTZWm+fN
LzyBWtczFYPxfQ9IqYzklyeou4ohfrcHzqN71IEtmGMXxob+i04QS9FQXaPitgBG
UORjwFVh8690n3ETQobjLrylOF5F/3+RdCGqanYOLgaJ0aix4+EByLz9FbxLPnJk
4Utijk2SKxLUb3dXZIfpwKtmPmvLJkFqwSazN5WDIg9Rjqz/H1p9UTWP0cfPRwJa
9INDZeK833kjYdtK6UMBpuNFkgGtpKTlhMX/cI78KYsEwVgK8r69b7uNr+2OUMgh
4i7dbHgb5/NpHlUlacVPTBvXf7C1iQ//vqh0Oc20lp/mAY1tVGuYRHno6QVyRtfS
DmCNPtbAgCa9FmP/t5NA8a3wana2ObTT2NCNMGEue7tJxVX4YaLpwIAEnUSHSJOQ
seI8HT2M1yEiSes9V+OuigHt3pKk68fMe0ZqDkovcd4QBlub6WTAPXWrXpbHtBCo
k+hT8TlDYaDbQkNDzXtg
=UyKm
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Here is the bulk of pin control changes for the v4.2 series: Quite a
lot of new SoC subdrivers and two new main drivers this time, apart
from that business as usual.
Details:
Core functionality:
- Enable exclusive pin ownership: it is possible to flag a pin
controller so that GPIO and other functions cannot use a single pin
simultaneously.
New drivers:
- NXP LPC18xx System Control Unit pin controller
- Imagination Pistachio SoC pin controller
New subdrivers:
- Freescale i.MX7d SoC
- Intel Sunrisepoint-H PCH
- Renesas PFC R8A7793
- Renesas PFC R8A7794
- Mediatek MT6397, MT8127
- SiRF Atlas 7
- Allwinner A33
- Qualcomm MSM8660
- Marvell Armada 395
- Rockchip RK3368
Cleanups:
- A big cleanup of the Marvell MVEBU driver rectifying it to
correspond to reality
- Drop platform device probing from the SH PFC driver, we are now a
DT only shop for SuperH
- Drop obsolte multi-platform check for SH PFC
- Various janitorial: constification, grammar etc
Improvements:
- The AT91 GPIO portions now supports the set_multiple() feature
- Split out SPI pins on the Xilinx Zynq
- Support DTs without specific function nodes in the i.MX driver"
* tag 'pinctrl-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: rockchip: add support for the rk3368
pinctrl: rockchip: generalize perpin driver-strength setting
pinctrl: sh-pfc: r8a7794: add SDHI pin groups
pinctrl: sh-pfc: r8a7794: add MMCIF pin groups
pinctrl: sh-pfc: add R8A7794 PFC support
pinctrl: make pinctrl_register() return proper error code
pinctrl: mvebu: armada-39x: add support for Armada 395 variant
pinctrl: mvebu: armada-39x: add missing SATA functions
pinctrl: mvebu: armada-39x: add missing PCIe functions
pinctrl: mvebu: armada-38x: add ptp functions
pinctrl: mvebu: armada-38x: add ua1 functions
pinctrl: mvebu: armada-38x: add nand functions
pinctrl: mvebu: armada-38x: add sata functions
pinctrl: mvebu: armada-xp: add dram functions
pinctrl: mvebu: armada-xp: add nand rb function
pinctrl: mvebu: armada-xp: add spi1 function
pinctrl: mvebu: armada-39x: normalize ref clock naming
pinctrl: mvebu: armada-xp: rename spi to spi0
pinctrl: mvebu: armada-370: align spi1 clock pin naming
pinctrl: mvebu: armada-370: align VDD cpu-pd pin naming with datasheet
...
Currently, pinctrl_register() just returns NULL on error, so the
callers can not know the exact reason of the failure.
Some of the pinctrl drivers return -EINVAL, some -ENODEV, and some
-ENOMEM on error of pinctrl_register(), although the error code
might be different from the real cause of the error.
This commit reworks pinctrl_register() to return the appropriate
error code and modifies all of the pinctrl drivers to use IS_ERR()
for the error checking and PTR_ERR() for getting the error code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Ray Jui <rjui@broadcom.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The num_pins field in the struct meson_domain_data must include also the
missing pins in the Meson8b SoC, otherwise the GPIO <-> pin mapping is
broken on this platform. Avoid also the dinamic allocation for GPIOs.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for the AmLogic Meson8b SoC.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the compatible string for Meson8b in Meson pinctrl documentation
and add new information for Meson8b in source code comments.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch introduces a new PIN macro and few small modifications to
simplify and shorten the Meson pinctrl drivers and cleanup the support
file for the AmLogic Meson8 SoC.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a driver for the pinmux and GPIO controller available in
Amlogic Meson SoCs. It currently supports only Meson8, however the
common code should be generic enough to work also for other SoCs after
having defined the proper set of functions and groups.
GPIO interrupts are not supported at the moment due to lack of
documentation.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Martin Blumenstingl