[ Upstream commit cd0eb354d4 ]
We are not supposed to spread quirks in 8250_port module especially
when we have a separate driver for the hardware in question.
Move quirk from generic module to the driver that uses it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240215145029.581389-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 801410b26a ]
During the handoff from earlycon to the real console driver, we have
two separate drivers operating on the same device concurrently. In the
case of the 8250 driver these concurrent accesses cause problems due
to the driver's use of banked registers, controlled by LCR.DLAB. It is
possible for the setup(), config_port(), pm() and set_mctrl() callbacks
to set DLAB, which can cause the earlycon code that intends to access
TX to instead access DLL, leading to missed output and corruption on
the serial line due to unintended modifications to the baud rate.
In particular, for setup() we have:
univ8250_console_setup()
-> serial8250_console_setup()
-> uart_set_options()
-> serial8250_set_termios()
-> serial8250_do_set_termios()
-> serial8250_do_set_divisor()
For config_port() we have:
serial8250_config_port()
-> autoconfig()
For pm() we have:
serial8250_pm()
-> serial8250_do_pm()
-> serial8250_set_sleep()
For set_mctrl() we have (for some devices):
serial8250_set_mctrl()
-> omap8250_set_mctrl()
-> __omap8250_set_mctrl()
To avoid such problems, let's make it so that the console is locked
during pre-registration calls to these callbacks, which will prevent
the earlycon driver from running concurrently.
Remove the partial solution to this problem in the 8250 driver
that locked the console only during autoconfig_irq(), as this would
result in a deadlock with the new approach. The console continues
to be locked during autoconfig_irq() because it can only be called
through uart_configure_port().
Although this patch introduces more locking than strictly necessary
(and in particular it also locks during the call to rs485_config()
which is not affected by this issue as far as I can tell), it follows
the principle that it is the responsibility of the generic console
code to manage the earlycon handoff by ensuring that earlycon and real
console driver code cannot run concurrently, and not the individual
drivers.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://linux-review.googlesource.com/id/I7cf8124dcebf8618e6b2ee543fa5b25532de55d8
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240304214350.501253-1-pcc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d27056c24 ]
When trying to instantiate a max14830 device from userspace:
echo max14830 0x60 > /sys/bus/i2c/devices/i2c-2/new_device
we get the following error:
Unable to handle kernel NULL pointer dereference at virtual address...
...
Call trace:
max310x_i2c_probe+0x48/0x170 [max310x]
i2c_device_probe+0x150/0x2a0
...
Add check for validity of devtype to prevent the error, and abort probe
with a meaningful error message.
Fixes: 2e1f2d9a9b ("serial: max310x: implement I2C support")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73b5a5c00b ]
It seems a copy&paste mistake that suspend callback removes the GPIO
device. There is no counterpart of this action, means once suspended
there is no more GPIO device available untile full unbind-bind cycle
is performed. Remove suspicious GPIO device removal in suspend.
Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240219150627.2101198-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 314c2b3992 ]
The core expects for tx_empty() either TIOCSER_TEMT when the tx is
empty or 0 otherwise. s3c24xx_serial_txempty_nofifo() might return
0x4, and at least uart_get_lsr_info() tries to clear exactly
TIOCSER_TEMT (BIT(1)). Fix tx_empty() to return TIOCSER_TEMT.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-2-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ede8c6f47 ]
Replace g with q.
Helpful when grepping thru source code or logs for
"request" keyword.
Fixes: f65444187a ("serial: New serial driver MAX310X")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e6a92f67c ]
The if (c >= 20 && c <= 0x3f) test added in commit 7a99565f87 is
wrong. 20 is DC4 in ascii and it makes no sense to consider that as the
bottom limit. Instead, it should be 0x20 as in the other test in
the commit above. This is supposed to NOT change anything as we handle
interesting 20-0x20 asciis far before this if.
So for sakeness, change to 0x20 (which is SPACE).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Fixes: 7a99565f87 ("vt: ignore csi sequences with intermediate characters.")
Cc: Martin Hostettler <textshell@uchuujin.de>
Link: https://lore.kernel.org/all/ZaP45QY2WEsDqoxg@neutronstar.dyndns.org/
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 188942f05c ]
mips_ejtag_fdc_encode() method expects having a first argument passed of
the "u8 **" type, meanwhile the driver passes the "const char **" type.
That causes the next build-warning:
drivers/tty/mips_ejtag_fdc.c: In function ‘mips_ejtag_fdc_console_write’:
drivers/tty/mips_ejtag_fdc.c:343:32: error: passing argument 1 of ‘mips_ejtag_fdc_encode’ from incompatible pointer type [-Werror=incompatible-pointer-types]
word = mips_ejtag_fdc_encode(&buf_ptr, &buf_len, 1);
^
drivers/tty/mips_ejtag_fdc.c:216:24: note: expected ‘const u8 ** {aka const unsigned char **}’ but argument is of type ‘const char **’
static struct fdc_word mips_ejtag_fdc_encode(const u8 **ptrs,
^~~~~~~~~~~~~~~~~~~~~
Fix it by altering the type of the pointer which is passed to the
mips_ejtag_fdc_encode() method.
Fixes: ce7cbd9a6c ("tty: mips_ejtag_fdc: use u8 for character pointers")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 5c7e105cd1.
As identified by KASAN, the simplification done by the cleanup patch
was not legal.
>From tracing through the code, it can be seen that we're transmitting
from a 4096-byte circular buffer. We copy anywhere from 1-4 bytes from
it each time. The simplification runs into trouble when we get near
the end of the circular buffer. For instance, we might start out with
xmit->tail = 4094 and we want to transfer 4 bytes. With the code
before simplification this was no problem. We'd read buf[4094],
buf[4095], buf[0], and buf[1]. With the new code we'll do a
memcpy(&buf[4094], 4) which reads 2 bytes past the end of the buffer
and then skips transmitting what's at buf[0] and buf[1].
KASAN isn't 100% consistent at reporting this for me, but to be extra
confident in the analysis, I added traces of the tail and tx_bytes and
then wrote a test program:
while true; do
echo -n "abcdefghijklmnopqrstuvwxyz0" > /dev/ttyMSM0
sleep .1
done
I watched the traces over SSH and saw:
qcom_geni_serial_send_chunk_fifo: 4093 4
qcom_geni_serial_send_chunk_fifo: 1 3
Which indicated that one byte should be missing. Sure enough the
output that should have been:
abcdefghijklmnopqrstuvwxyz0
In one case was actually missing a byte:
abcdefghijklmnopqrstuvwyz0
Running "ls -al" on large directories also made the missing bytes
obvious since columns didn't line up.
While the original code may not be the most elegant, we only talking
about copying up to 4 bytes here. Let's just go back to the code that
worked.
Fixes: 5c7e105cd1 ("tty: serial: simplify qcom_geni_serial_send_chunk_fifo()")
Cc: stable <stable@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240304174952.1.I920a314049b345efd1f69d708e7f74d2213d0b49@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the remote uart device is not connected or not enabled after booting
up, the CTS line is high by default. At this time, if we enable the flow
control when opening the device(for example, using “stty -F /dev/ttyLP4
crtscts” command), there will be a pending idle preamble(first writing 0
and then writing 1 to UARTCTRL_TE will queue an idle preamble) that
cannot be sent out, resulting in the uart port fail to close(waiting for
TX empty), so the user space stty will have to wait for a long time or
forever.
This is an LPUART IP bug(idle preamble has higher priority than CTS),
here add a workaround patch to enable TX CTS after enabling UARTCTRL_TE,
so that the idle preamble does not get stuck due to CTS is deasserted.
Fixes: 380c966c09 ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20240305015706.1050769-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the same issue that was fixed for the VGA text buffer in commit
39cdb68c64 ("vt: fix memory overlapping when deleting chars in the
buffer"). The cure is also the same i.e. replace memcpy() with memmove()
due to the overlaping buffers.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Fixes: 81732c3b2f ("tty vt: Fix line garbage in virtual console on command line edition")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/sn184on2-3p0q-0qrq-0218-895349s4753o@syhkavp.arg
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We accidently met the issue that the bash prompt is not shown after the
previous command done and until the next input if there's only one CPU
(In our issue other CPUs are isolated by isolcpus=). Further analysis
shows it's because the port entering runtime suspend even if there's
still pending chars in the buffer and the pending chars will only be
processed in next device resuming. We are using amba-pl011 and the
problematic flow is like below:
Bash kworker
tty_write()
file_tty_write()
n_tty_write()
uart_write()
__uart_start()
pm_runtime_get() // wakeup waker
queue_work()
pm_runtime_work()
rpm_resume()
status = RPM_RESUMING
serial_port_runtime_resume()
port->ops->start_tx()
pl011_tx_chars()
uart_write_wakeup()
[…]
__uart_start()
pm_runtime_get() < 0 // because runtime status = RPM_RESUMING
// later data are not commit to the port driver
status = RPM_ACTIVE
rpm_idle() -> rpm_suspend()
This patch tries to fix this by checking the port busy before entering
runtime suspending. A runtime_suspend callback is added for the port
driver. When entering runtime suspend the callback is invoked, if there's
still pending chars in the buffer then flush the buffer.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Cc: stable <stable@kernel.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/20240226152351.40924-1-yangyicong@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When userspace opens the console, we call set_termios() passing a
termios with the console's configured baud rate. Currently this causes
dw8250_set_termios() to disable and then re-enable the UART clock at
the same frequency as it was originally. This can cause corruption
of any concurrent console output. Fix it by skipping the reclocking
if we are already at the correct rate.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Fixes: 4e26b134bd ("serial: 8250_dw: clock rate handling for all ACPI platforms")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240222192635.1050502-1-pcc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When about to transmit the function imx_uart_start_tx is called and in
some RS485 configurations this function will call imx_uart_stop_rx. The
problem is that imx_uart_stop_rx will enable loopback in order to
release the RS485 bus, but when loopback is enabled transmitted data
will just be looped to RX.
This patch fixes the above problem by not enabling loopback when about
to transmit.
This driver now works well when used for RS485 half duplex master
configurations.
Fixes: 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal active high")
Cc: stable <stable@kernel.org>
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20240221115304.509811-1-rickaran@axis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA is used in RS485 mode make sure that the UARTs tx section is
enabled before the DMA buffers are queued for transmission.
Cc: stable@vger.kernel.org
Fixes: 8d47923772 ("serial: amba-pl011: add RS485 support")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240216224709.9928-2-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before commit 07c30ea586 ("serial: Do not hold the port lock when setting
rx-during-tx GPIO") the SER_RS485_RX_DURING_TX flag was only set if the
rx-during-tx mode was not controlled by a GPIO. Now the flag is set
unconditionally when RS485 is enabled. This results in an incorrect setting
if the rx-during-tx GPIO is not asserted.
Fix this by setting the flag only if the rx-during-tx mode is not
controlled by a GPIO and thus restore the correct behaviour.
Cc: stable@vger.kernel.org # 6.6+
Fixes: 07c30ea586 ("serial: Do not hold the port lock when setting rx-during-tx GPIO")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240216224709.9928-1-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new SBI console has the same problem as the old one: there's only
one shared backing hardware and no synchronization, so the two drivers
end up stepping on each other. This was the same issue the old SBI-0.1
console drivers had, but that was disabled by default when SBI-0.1 was.
So just mark the new driver as nonportable.
Reported-by: Emil Renner Berthing <kernel@esmil.dk>
Fixes: 88ead68e76 ("tty: Add SBI debug console support to HVC SBI driver")
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240214153429.16484-2-palmer@rivosinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emil reports:
After updating Linux on an i.MX28 board, serial communication over
AUART broke. When I TX from the board and measure on the TX pin, it
seems like the HW fifo is not emptied before the transmission is
stopped.
MXS performs weird things with stop_tx(). The driver makes it
conditional on uart_tx_stopped().
So the driver needs special handling. Pass the brand new UART_TX_NOSTOP
to uart_port_tx_flags() and handle the stop on its own.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reported-by: Emil Kronborg <emil.kronborg@protonmail.com>
Cc: stable <stable@kernel.org>
Fixes: 2d141e683e ("tty: serial: use uart_port_tx() helper")
Closes: https://lore.kernel.org/all/miwgbnvy3hjpnricubg76ytpn7xoceehwahupy25bubbduu23s@om2lptpa26xw/
Tested-by: Stefan Wahren <wahrenst@gmx.net>
Tested-by: Emil Kronborg <emil.kronborg@protonmail.com>
Link: https://lore.kernel.org/r/20240201105557.28043-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I was reviewing this code again and I realized I made a mistake here.
It should have been > instead of >=. The subtract ensures that we
don't go out of bounds. My patch meant that we don't read the last
chunk of the buffer.
Fixes: 86ee55e9bc ("serial: 8250_pci1xxxx: fix off by one in pci1xxxx_process_read_data()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/bd6fb361-bbb9-427d-90e8-a5df4de76221@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is a problem after resetting a port, the do/while() loop that
checks the default value of DIVLSB register may run forever and spam the
I2C bus.
Add a delay before each read of DIVLSB, and a maximum number of tries to
prevent that situation from happening.
Also fail probe if port reset is unsuccessful.
Fixes: 10d8b34a42 ("serial: max310x: Driver rework")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some people are seeing a warning similar to this when using a crystal:
max310x 11-006c: clock is not stable yet
The datasheet doesn't mention the maximum time to wait for the clock to be
stable when using a crystal, and it seems that the 10ms delay in the driver
is not always sufficient.
Jan Kundrát reported that it took three tries (each separated by 10ms) to
get a stable clock.
Modify behavior to check stable clock ready bit multiple times (20), and
waiting 10ms between each try.
Note: the first draft of the driver originally used a 50ms delay, without
checking the clock stable bit.
Then a loop with 1000 retries was implemented, each time reading the clock
stable bit.
Fixes: 4cf9a888fd ("serial: max310x: Check the clock readiness")
Cc: stable@vger.kernel.org
Suggested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://www.spinics.net/lists/linux-serial/msg35773.html
Link: https://lore.kernel.org/all/20240110174015.6f20195fde08e5c9e64e5675@hugovil.com/raw
Link: e5dfe3e4a7
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If regmap_read() returns a non-zero value, the 'val' variable can be left
uninitialized.
Clear it before calling regmap_read() to make sure we properly detect
the clock ready bit.
Fixes: 4cf9a888fd ("serial: max310x: Check the clock readiness")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In uart_tiocmget():
result = uport->mctrl;
uart_port_lock_irq(uport);
result |= uport->ops->get_mctrl(uport);
uart_port_unlock_irq(uport);
...
return result;
In uart_update_mctrl():
uart_port_lock_irqsave(port, &flags);
...
port->mctrl = (old & ~clear) | set;
...
port->ops->set_mctrl(port, port->mctrl);
...
uart_port_unlock_irqrestore(port, flags);
An atomicity violation is identified due to the concurrent execution of
uart_tiocmget() and uart_update_mctrl(). After assigning
result = uport->mctrl, the mctrl value may change in uart_update_mctrl(),
leading to a mismatch between the value returned by
uport->ops->get_mctrl(uport) and the mctrl value previously read.
This can result in uart_tiocmget() returning an incorrect value.
This possible bug is found by an experimental static analysis tool
developed by our team, BassCheck[1]. This tool analyzes the locking APIs
to extract function pairs that can be concurrently executed, and then
analyzes the instructions in the paired functions to identify possible
concurrency bugs including data races and atomicity violations. The above
possible bug is reported when our tool analyzes the source code of
Linux 5.17.
To address this issue, it is suggested to move the line
result = uport->mctrl inside the uart_port_lock block to ensure atomicity
and prevent the mctrl value from being altered during the execution of
uart_tiocmget(). With this patch applied, our tool no longer reports the
bug, with the kernel configuration allyesconfig for x86_64. Due to the
absence of the requisite hardware, we are unable to conduct runtime
testing of the patch. Therefore, our verification is solely based on code
logic analysis.
[1] https://sites.google.com/view/basscheck/
Fixes: c5f4644e6c ("[PATCH] Serial: Adjust serial locking")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <2045gemini@gmail.com>
Link: https://lore.kernel.org/r/20240112113624.17048-1-2045gemini@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These > comparisons should be >= to prevent writing one element beyond
the end of the rx_buff[] array. The rx_buff[] buffer has RX_BUF_SIZE
elements. Fix the buffer overflow.
Fixes: aba8290f36 ("8250: microchip: pci1xxxx: Add Burst mode reception support in uart driver for writing into FIFO")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/ZZ7vIfj7Jgh-pJn8@moroto
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This includes everything from part 2:
* Support for tuning for systems with fast misaligned accesses.
* Support for SBI-based suspend.
* Support for the new SBI debug console extension.
* The T-Head CMOs now use PA-based flushes.
* Support for enabling the V extension in kernel code.
* Optimized IP checksum routines.
* Various ftrace improvements.
* Support for archrandom, which depends on the Zkr extension.
and then also a fix for those:
* The build is no longer broken under NET=n, KUNIT=y for ports that
don't define their own ipv6 checksum.
-----BEGIN PGP SIGNATURE-----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=Sjhj
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
- Support for tuning for systems with fast misaligned accesses.
- Support for SBI-based suspend.
- Support for the new SBI debug console extension.
- The T-Head CMOs now use PA-based flushes.
- Support for enabling the V extension in kernel code.
- Optimized IP checksum routines.
- Various ftrace improvements.
- Support for archrandom, which depends on the Zkr extension.
- The build is no longer broken under NET=n, KUNIT=y for ports that
don't define their own ipv6 checksum.
* tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (56 commits)
lib: checksum: Fix build with CONFIG_NET=n
riscv: lib: Check if output in asm goto supported
riscv: Fix build error on rv32 + XIP
riscv: optimize ELF relocation function in riscv
RISC-V: Implement archrandom when Zkr is available
riscv: Optimize hweight API with Zbb extension
riscv: add dependency among Image(.gz), loader(.bin), and vmlinuz.efi
samples: ftrace: Add RISC-V support for SAMPLE_FTRACE_DIRECT[_MULTI]
riscv: ftrace: Add DYNAMIC_FTRACE_WITH_DIRECT_CALLS support
riscv: ftrace: Make function graph use ftrace directly
riscv: select FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY
lib/Kconfig.debug: Update AS_HAS_NON_CONST_LEB128 comment and name
riscv: Restrict DWARF5 when building with LLVM to known working versions
riscv: Hoist linker relaxation disabling logic into Kconfig
kunit: Add tests for csum_ipv6_magic and ip_fast_csum
riscv: Add checksum library
riscv: Add checksum header
riscv: Add static key for misaligned accesses
asm-generic: Improve csum_fold
RISC-V: selftests: cbo: Ensure asm operands match constraints
...
Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaedng8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yndHACfX3SA2ipK5umpMsWOoLMCBV6VyrwAn3t+FPd/
z4mNiCuNUhbEnU7RinK0
=k/E9
-----END PGP SIGNATURE-----
Merge tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: typec: tipd: fix use of device-specific init function
usb: typec: tipd: Separate reset for TPS6598x
usb: mon: Fix atomicity violation in mon_bin_vma_fault
usb: gadget: uvc: Remove nested locking
usb: gadget: uvc: Fix use are free during STREAMOFF
usb: typec: class: fix typec_altmode_put_partner to put plugs
dt-bindings: usb: dwc3: Limit num-hc-interrupters definition
dt-bindings: usb: xhci: Add num-hc-interrupters definition
xhci: add support to allocate several interrupters
USB: core: Use device_driver directly in struct usb_driver and usb_device_driver
arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry
usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue
arm64: dts: qcom: msm8996: Remove PNoC clock from MSS
arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8939: Drop RPM bus clocks
arm64: dts: qcom: sdm630: Drop RPM bus clocks
arm64: dts: qcom: qcs404: Drop RPM bus clocks
arm64: dts: qcom: msm8996: Drop RPM bus clocks
...
Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty core
and drivers in here, along with the usual set of rs485 updates (someday
this might work properly...) Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaeUaw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykyOgCgp1uhP/b9iW6qM7qL6OYEG6idI0kAnj0VASNm
vSI69HmdKKwo69YLOSBp
=14n1
-----END PGP SIGNATURE-----
Merge tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty
core and drivers in here, along with the usual set of rs485 updates
(someday this might work properly...)
Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (197 commits)
serial: sc16is7xx: refactor EFR lock
serial: sc16is7xx: reorder code to remove prototype declarations
serial: sc16is7xx: refactor FIFO access functions to increase commonality
serial: sc16is7xx: drop unneeded MODULE_ALIAS
serial: sc16is7xx: replace hardcoded divisor value with BIT() macro
serial: sc16is7xx: add explicit return for some switch default cases
serial: sc16is7xx: add macro for max number of UART ports
serial: sc16is7xx: add driver name to struct uart_driver
serial: sc16is7xx: use i2c_get_match_data()
serial: sc16is7xx: use spi_get_device_match_data()
serial: sc16is7xx: use DECLARE_BITMAP for sc16is7xx_lines bitfield
serial: sc16is7xx: improve do/while loop in sc16is7xx_irq()
serial: sc16is7xx: remove obsolete loop in sc16is7xx_port_irq()
serial: sc16is7xx: set safe default SPI clock frequency
serial: sc16is7xx: add check for unsupported SPI modes during probe
serial: sc16is7xx: fix invalid sc16is7xx_lines bitfield in case of probe error
serial: 8250_exar: Set missing rs485_supported flag
serial: omap: do not override settings for RS485 support
serial: core, imx: do not set RS485 enabled if it is not supported
serial: core: make sure RS485 cannot be enabled when it is not supported
...
- Add support for Allwinner A100 RGB LED controller
- Add support for Maxim 5970 Dual Hot-swap controller
- New Device Support
- Add support for AW20108 to Awinic LED driver
- New Functionality
- Extend support for Net speeds to include; 2.5G, 5G and 10G
- Allow tx/rx and cts/dsr/dcd/rng TTY LEDS to be turned on and off via sysfs if required
- Add support for hardware control in AW200xx
- Fix-ups
- Use safer methods for string handling
- Improve error handling; return proper error values, simplify, avoid duplicates, etc
- Replace Mutex use with the Completion mechanism
- Fix include lists; alphabetise, remove unused, explicitly add used
- Use generic platform device properties
- Use/convert to new/better APIs/helpers/MACROs instead of hand-rolling implementations
- Device Tree binding adaptions/conversions/creation
- Continue work to remove superfluous platform .remove() call-backs
- Remove superfluous/defunct code
- Trivial; whitespace, unused variables, spelling, clean-ups, etc
- Avoid unnecessary duplicate locks
- Bug Fixes
- Repair Kconfig based dependency lists
- Ensure unused dynamically allocated data is freed after use
- Fix support for brightness control
- Add missing sufficient delays during reset to ensure correct operation
- Avoid division-by-zero issues
-----BEGIN PGP SIGNATURE-----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=/f98
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Drivers:
- Add support for Allwinner A100 RGB LED controller
- Add support for Maxim 5970 Dual Hot-swap controller
New Device Support:
- Add support for AW20108 to Awinic LED driver
New Functionality:
- Extend support for Net speeds to include; 2.5G, 5G and 10G
- Allow tx/rx and cts/dsr/dcd/rng TTY LEDS to be turned on and off
via sysfs if required
- Add support for hardware control in AW200xx
Fix-ups:
- Use safer methods for string handling
- Improve error handling; return proper error values, simplify,
avoid duplicates, etc
- Replace Mutex use with the Completion mechanism
- Fix include lists; alphabetise, remove unused, explicitly add used
- Use generic platform device properties
- Use/convert to new/better APIs/helpers/MACROs instead of
hand-rolling implementations
- Device Tree binding adaptions/conversions/creation
- Continue work to remove superfluous platform .remove() call-backs
- Remove superfluous/defunct code
- Trivial; whitespace, unused variables, spelling, clean-ups, etc
- Avoid unnecessary duplicate locks
Bug Fixes:
- Repair Kconfig based dependency lists
- Ensure unused dynamically allocated data is freed after use
- Fix support for brightness control
- Add missing sufficient delays during reset to ensure correct
operation
- Avoid division-by-zero issues"
* tag 'leds-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (45 commits)
leds: trigger: netdev: Add core support for hw not supporting fallback to LED sw control
leds: trigger: panic: Don't register panic notifier if creating the trigger failed
leds: sun50i-a100: Convert to be agnostic to property provider
leds: max5970: Add missing headers
leds: max5970: Make use of dev_err_probe()
leds: max5970: Make use of device properties
leds: max5970: Remove unused variable
leds: rgb: Drop obsolete dependency on COMPILE_TEST
leds: sun50i-a100: Avoid division-by-zero warning
leds: trigger: Remove unused function led_trigger_rename_static()
leds: qcom-lpg: Introduce a wrapper for getting driver data from a pwm chip
leds: gpio: Add kernel log if devm_fwnode_gpiod_get() fails
dt-bindings: leds: qcom,spmi-flash-led: Fix example node name
dt-bindings: leds: aw200xx: Fix led pattern and add reg constraints
dt-bindings: leds: awinic,aw200xx: Add AW20108 device
leds: aw200xx: Add support for aw20108 device
leds: aw200xx: Improve autodim calculation method
leds: aw200xx: Enable disable_locking flag in regmap config
leds: aw200xx: Add delay after software reset
dt-bindings: leds: aw200xx: Remove property "awinic,display-rows"
...
A new drivers/cache/ subsystem is added to contain drivers for abstracting
cache flush methods on riscv and potentially others, as this is needed for
handling non-coherent DMA but several SoCs require nonstandard hardware
methods for it.
op-tee gains support for asynchronous notification with FF-A, as well
as support for a system thread for executing in secure world.
The tee, reset, bus, memory and scmi subsystems have a couple of minor
updates.
Platform specific soc driver changes include:
- Samsung Exynos gains driver support for Google GS101 (Tensor G1)
across multiple subsystems
- Qualcomm Snapdragon gains support for SM8650 and X1E along with
added features for some other SoCs
- Mediatek adds support for "Smart Voltage Scaling" on MT8186 and MT8195,
and driver support for MT8188 along with some code refactoring.
- Microchip Polarfire FPGA support for "Auto Update" of the FPGA bitstream
- Apple M1 mailbox driver is rewritten into a SoC driver
- minor updates on amlogic, mvebu, ti, zynq, imx, renesas and hisilicon
-----BEGIN PGP SIGNATURE-----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=4bKY
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"A new drivers/cache/ subsystem is added to contain drivers for
abstracting cache flush methods on riscv and potentially others, as
this is needed for handling non-coherent DMA but several SoCs require
nonstandard hardware methods for it.
op-tee gains support for asynchronous notification with FF-A, as well
as support for a system thread for executing in secure world.
The tee, reset, bus, memory and scmi subsystems have a couple of minor
updates.
Platform specific soc driver changes include:
- Samsung Exynos gains driver support for Google GS101 (Tensor G1)
across multiple subsystems
- Qualcomm Snapdragon gains support for SM8650 and X1E along with
added features for some other SoCs
- Mediatek adds support for "Smart Voltage Scaling" on MT8186 and
MT8195, and driver support for MT8188 along with some code
refactoring.
- Microchip Polarfire FPGA support for "Auto Update" of the FPGA
bitstream
- Apple M1 mailbox driver is rewritten into a SoC driver
- minor updates on amlogic, mvebu, ti, zynq, imx, renesas and
hisilicon"
* tag 'soc-drivers-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (189 commits)
memory: ti-emif-pm: Convert to platform remove callback returning void
memory: ti-aemif: Convert to platform remove callback returning void
memory: tegra210-emc: Convert to platform remove callback returning void
memory: tegra186-emc: Convert to platform remove callback returning void
memory: stm32-fmc2-ebi: Convert to platform remove callback returning void
memory: exynos5422-dmc: Convert to platform remove callback returning void
memory: renesas-rpc-if: Convert to platform remove callback returning void
memory: omap-gpmc: Convert to platform remove callback returning void
memory: mtk-smi: Convert to platform remove callback returning void
memory: jz4780-nemc: Convert to platform remove callback returning void
memory: fsl_ifc: Convert to platform remove callback returning void
memory: fsl-corenet-cf: Convert to platform remove callback returning void
memory: emif: Convert to platform remove callback returning void
memory: brcmstb_memc: Convert to platform remove callback returning void
memory: brcmstb_dpfe: Convert to platform remove callback returning void
soc: qcom: llcc: Fix LLCC_TRP_ATTR2_CFGn offset
firmware: qcom: qseecom: fix memory leaks in error paths
dt-bindings: clock: google,gs101: rename CMU_TOP gate defines
soc: qcom: llcc: Fix typo in kernel-doc
dt-bindings: soc: qcom,aoss-qmp: document the X1E80100 Always-On Subsystem side channel
...
We extend the existing RISC-V SBI earlycon support to use the new
RISC-V SBI debug console extension.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231124070905.1043092-4-apatel@ventanamicro.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Move common code for EFR lock/unlock of mutex into functions for code reuse
and clarity.
With the addition of old_lcr, move irda_mode within struct sc16is7xx_one to
reduce memory usage:
Before: /* size: 752, cachelines: 12, members: 10 */
After: /* size: 744, cachelines: 12, members: 10 */
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-17-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move/reorder some functions to remove sc16is7xx_ier_set() and
sc16is7xx_stop_tx() prototypes declarations.
No functional change.
sc16is7xx_ier_set() was introduced in
commit cc4c1d05eb ("sc16is7xx: Properly resume TX after stop").
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-16-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify FIFO access functions by avoiding to declare
a struct sc16is7xx_port *s variable within each function.
This is mainly done to have more commonality between the max310x and
sc16is7xx drivers.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-15-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MODULE_DEVICE_TABLE() already creates the proper aliases for the
SPI driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-14-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To better show why the limit is what it is, since we have only 16 bits for
the divisor.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-13-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows to simplify code by removing the break statement in the default
switch/case in some functions.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-12-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that the driver name is displayed instead of "unknown" when
displaying the driver infos:
Before:
grep ttySC /proc/tty/drivers
unknown /dev/ttySC 243 0-7 serial
After:
grep ttySC /proc/tty/drivers
sc16is7xx /dev/ttySC 243 0-7 serial
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-10-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use preferred i2c_get_match_data() instead of device_get_match_data()
and i2c_client_get_device_id() to get the driver match data.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-9-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use preferred spi_get_device_match_data() instead of
device_get_match_data() and spi_get_device_id() to get the driver match
data.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-8-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the explicit sc16is7xx_lines bitfield declaration with the generic
macro DECLARE_BITMAP() to reserve just enough memory to contain all
required bits.
This also improves code self-documentation by showing the maximum number
of bits required.
This conversion now makes sc16is7xx_lines an array, so drop the "&" before
sc16is7xx_lines in all bit access functions.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-7-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify and improve readability by replacing while(1) loop with
do {} while, and by using the keep_polling variable as the exit
condition, making it more explicit.
Fixes: 8344498721 ("sc16is7xx: Fix for multi-channel stall")
Cc: <stable@vger.kernel.org>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8344498721 ("sc16is7xx: Fix for multi-channel stall") changed
sc16is7xx_port_irq() from looping multiple times when there was still
interrupts to serve. It simply changed the do {} while(1) loop to a
do {} while(0) loop, which makes the loop itself now obsolete.
Clean the code by removing this obsolete do {} while(0) loop.
Fixes: 8344498721 ("sc16is7xx: Fix for multi-channel stall")
Cc: <stable@vger.kernel.org>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
15 MHz is supported only by 76x variants.
If the SPI clock frequency is not specified, use a safe default clock value
of 4 MHz that is supported by all variants.
Also use HZ_PER_MHZ macro to improve readability.
Fixes: 2c837a8a8f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original comment is confusing because it implies that variants other
than the SC16IS762 supports other SPI modes beside SPI_MODE_0.
Extract from datasheet:
The SC16IS762 differs from the SC16IS752 in that it supports SPI clock
speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the
SC16IS752... In all other aspects, the SC16IS762 is functionally and
electrically the same as the SC16IS752.
The same is also true of the SC16IS760 variant versus the SC16IS740 and
SC16IS750 variants.
For all variants, only SPI mode 0 is supported.
Change comment and abort probing if the specified SPI mode is not
SPI_MODE_0.
Fixes: 2c837a8a8f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an error occurs during probing, the sc16is7xx_lines bitfield may be left
in a state that doesn't represent the correct state of lines allocation.
For example, in a system with two SC16 devices, if an error occurs only
during probing of channel (port) B of the second device, sc16is7xx_lines
final state will be 00001011b instead of the expected 00000011b.
This is caused in part because of the "i--" in the for/loop located in
the out_ports: error path.
Fix this by checking the return value of uart_add_one_port() and set line
allocation bit only if this was successful. This allows the refactor of
the obfuscated for(i--...) loop in the error path, and properly call
uart_remove_one_port() only when needed, and properly unset line allocation
bits.
Also use same mechanism in remove() when calling uart_remove_one_port().
Fixes: c64349722d ("sc16is7xx: support multiple devices")
Cc: <stable@vger.kernel.org>
Cc: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART supports an auto-RTS mode in which the RTS pin is automatically
activated during transmission. So mark this mode as being supported even
if RTS is not controlled by the driver but the UART.
Also the serial core expects now at least one of both modes rts-on-send or
rts-after-send to be supported. This is since during sanitization
unsupported flags are deleted from a RS485 configuration set by userspace.
However if the configuration ends up with both flags unset, the core prints
a warning since it considers such a configuration invalid (see
uart_sanitize_serial_rs485()).
Cc: <stable@vger.kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-8-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drivers RS485 support is deactivated if there is no RTS GPIO available.
This is done by nullifying the ports rs485_supported struct. After that
however the settings in serial_omap_rs485_supported are assigned to the
same structure unconditionally, which results in an unintended reactivation
of RS485 support.
Fix this by moving the assignment to the beginning of
serial_omap_probe_rs485() and thus before uart_get_rs485_mode() gets
called.
Also replace the assignment of rs485_config() to have the complete RS485
setup in one function.
Fixes: e2752ae3cf ("serial: omap: Disallow RS-485 if rts-gpio is not specified")
Cc: <stable@vger.kernel.org>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240103061818.564-7-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
