Add the new PCI ID 0x1d17 0x3288 Zhaoxin controller support
Signed-off-by: Tony W Wang-oc <TonyWWang-oc@zhaoxin.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The legacy HD-Audio driver cannot handle Skylake+ platforms with
digital microphones. For those platforms, the SOF or SST drivers need
to be used.
This patch provides an automatic way of detecting the presence of
DMICs using NHTL information reported by the BIOS. A kernel kconfig
option or a kernel module parameter provide an opt-in means of
stopping the probe. The kernel would then look for an alternate driver
registered for the same PCI ID to probe.
With this capability, distros no longer have to blacklist
snd-hda-intel, but still need to make sure the SOF/SST drivers are
functional by providing the relevant firmware and topology files in
/lib/firmware/intel
The coexistence between SOF and SST drivers and their dynamic
detection is not addressed by this patch, different mechanisms need to
be used, e.g. DMI-based quirks.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turned out that the recent Intel HD-audio controller chips show a
significant stall during the system PM resume intermittently. It
doesn't happen so often and usually it may read back successfully
after one or more seconds, but in some rare worst cases the driver
went into fallback mode.
After trial-and-error, we found out that the communication stall seems
covered by issuing the sync after each verb write, as already done for
AMD and other chipsets. So this patch enables the write-sync flag for
the recent Intel chips, Skylake and onward, as a workaround.
Also, since Broxton and co have the very same driver flags as Skylake,
refer to the Skylake driver flags instead of defining the same
contents again for simplification.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201901
Reported-and-tested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a very big update, mainly thanks to Morimoto-san's refactoring
work and some fairly large new drivers.
- Lots more work on moving towards a component based framework from
Morimoto-san.
- Support for force disconnecting muxes from Jerome Brunet.
- New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90, Conexant
CX2072X, Realtek RT1011 and RT1308.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl0jGwUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LD4B/9AkutfS+vznOrk0V0wFb2SUfjwE4Pr
+z/kAehohAOl/7pg9Dun/lmZYBWMyOM2aYmK81ahEo2DfO+uzwkwjCaXFjGVGwEK
j7XpWkrIjKnou/z1FeALgVvt+crzdy5iNWC04AbKaP2WHCcI7zvPQIsBta/V0OJt
lg+j0J7pagnTMcgV1+qJdaASmofy/hpoZ79Gv0PIfGC8hpJ/3mBgcNPCLQrJtD4R
v+tzvCZNrZVqCanwLf3vouEm1bpWYOpI+Wdmu4u6rY7MhmCj72EJ2zyfdm/qtaxF
e7whgCyOQFkWe7NgDn0G08aAT6LsaxOtPNr7H8tL8S8sw8425fqeOouV
=n/HQ
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.3
This is a very big update, mainly thanks to Morimoto-san's refactoring
work and some fairly large new drivers.
- Lots more work on moving towards a component based framework from
Morimoto-san.
- Support for force disconnecting muxes from Jerome Brunet.
- New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90, Conexant
CX2072X, Realtek RT1011 and RT1308.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add HD Audio Device PCI ID for the Intel Elkhart Lake
platform.
Signed-off-by: Lai, Poey Seng <poey.seng.lai@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We observed the same issue as reported by commit a8d7bde23e
("ALSA: hda - Force polling mode on CFL for fixing codec communication")
We don't have a better solution. So apply the same workaround to CNL.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
polling mode is a useful function in the get_response function. Move
polling_mode flag from struct azx to struct hdac_bus so people can
implement polling mode in their own get_response function without
adding a polling_mode flag in their local chip structure.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We will move the polling_mode flag from struct azx to struct hdac_bus,
and the flag should be assigned after bus init.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the IRQ handler in HD-audio controller driver is registered
before the chip initialization. That is, we have some window opened
between the azx_acquire_irq() call and the CORB/RIRB setup. If an
interrupt is triggered in this small window, the IRQ handler may
access to the uninitialized RIRB buffer, which leads to a NULL
dereference Oops.
This is usually no big problem since most of Intel chips do register
the IRQ via MSI, and we've already fixed the order of the IRQ
enablement and the CORB/RIRB setup in the former commit b61749a89f
("sound: enable interrupt after dma buffer initialization"), hence the
IRQ won't be triggered in that room. However, some platforms use a
shared IRQ, and this may allow the IRQ trigger by another source.
Another possibility is the kdump environment: a stale interrupt might
be present in there, the IRQ handler can be falsely triggered as well.
For covering this small race, let's move the azx_acquire_irq() call
after hda_intel_init_chip() call. Although this is a bit radical
change, it can cover more widely than checking the CORB/RIRB setup
locally in the callee side.
Reported-by: Liwei Song <liwei.song@windriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently we set CONFIG_SND_HDA_POWER_SAVE_DEFAULT to 1 when
configuring the kernel, then two machines were reported to have noise
after installing the new kernel. Put them in the blacklist, the
noise disappears.
https://bugs.launchpad.net/bugs/1821663
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 3baffc4a84 (ALSA: hda/intel: Refactoring PM code) changed
the behaviour of azx_resume(), it triggers the jackpoll_work after
applying this commit.
This change introduced a new issue, all codecs are runtime active
after S3, and will not call runtime_suspend() automatically.
The root cause is the jackpoll_work calls snd_hda_power_up/down_pm,
and it calls up_pm before snd_hdac_enter_pm is called, while calls
the down_pm in the middle of enter_pm and leave_pm is called. This
makes the dev->power.usage_count unbalanced after S3.
To fix it, let azx_resume() don't trigger jackpoll_work as before
it did.
Fixes: 3baffc4a84 ("ALSA: hda/intel: Refactoring PM code")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Another machine which does not like the power saving (noise):
https://bugzilla.redhat.com/show_bug.cgi?id=1689623
Also, reorder the Lenovo C50 entry to keep the table sorted.
Reported-by: hs.guimaraes@outlook.com
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current code, the codec registration may happen both at the
codec bind time and the end of the controller probe time. In a rare
occasion, they race with each other, leading to Oops due to the still
uninitialized card device.
This patch introduces a simple flag to prevent the codec registration
at the codec bind time as long as the controller probe is going on.
The controller probe invokes snd_card_register() that does the whole
registration task, and we don't need to register each piece
beforehand.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This essentially reverts the commits
c337104b1a ("ALSA: HD-Audio: SKL+: abort probe if DSP is present
and Skylake driver selected")
and
d82b51c855 ("ALSA: HD-Audio: SKL+: force HDaudio legacy or SKL+
driver selection")
for the path of legacy HD-audio controller (snd-hda-intel).
The automatic DSP detection and skip of binding with the legacy driver
caused regressions on several machines like Dell XPS13. They give the
PCI class 0x40380 indicating the availability of DSP while they don't
work with ASoC SKL driver (yet).
As the support of ASoC driver for such devices isn't available, it's
better to revert the whole DSP-detection-and-skip behavior of the
legacy driver, so that we can get the old good driver working on such
devices.
The pci_binding option for ASoC SKL driver is still kept so that it
can work without blacklisting.
Fixes: c337104b1a ("ALSA: HD-Audio: SKL+: abort probe if DSP is present and Skylake driver selected")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reported-by: Azat Khuzhin <dohardgopro@gmail.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For HDaudio and Skylake drivers, add module parameter "pci_binding"
When pci_binding == 0 (AUTO), the PCI class/subclass info is used to
select drivers based on the presence of the DSP.
pci_binding == 1 (LEGACY) forces the use of the HDAudio legacy driver,
even if the DSP is present.
pci_binding == 2 (ASOC) forces the use of the ASOC driver. The
information on the DSP presence is bypassed.
The value for the module parameter needs to be identical for both
drivers. This parameter is intended as a back-up solution if the
automatic detection fails or when the DSP usage fails. Such cases
should be reported on the alsa-devel mailing list for analysis.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that the SST/Skylake driver supports per platform selectors, we
can add logic to automatically select the right driver.
If the Skylake driver is selected for a specific platform, and the DSP
is detected at run-time based on the PCI class/subclass/prog-if
information, the legacy HDaudio driver aborts the probe. This will
result in a single driver probing and remove the need for modprobe
blacklists.
Follow-up patches will add a module parameter to bypass the logic if
this automatic detection fails, or if the Skylake driver is unable to
actually support the platform (firmware authentication, missing
topology file, hardware issue, etc).
The same mechanism will be used to conflicts generated by the same PCI
ID being registered by both legacy HDAuudio and SOF drivers for Intel
platforms. In other words SOF will not require changes to the HDaudio
legacy.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After the recent refactoring, snd_hdac_display_power() doesn't return
any error, hence it can be defined to return void.
This makes many error checks redundant and allows us to reduce them
gracefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When an error occurs in azx_probe_continue(), we should release the
display power. However, the current code ignores it and releases the
display power only for HSW/BDW cases. Fix it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hdac_display_power() can be called even for a HDA controller
without DRM binding. The same is true for other helpers,
snd_hdac_i915_set_bclk() and snd_hdac_set_codec_wakeup().
So all superfluous AZX_DCAPS_I915_POWERWELL checks in hda_intel.c can
be dropped, and the definition of AZX_DCAPS_I915_POWERWELL itself can
be removed as well. This simplifies the code a lot.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current HD-audio code manages the DRM audio power via too complex
redirections, and this seems even still unbalanced in a corner case as
Intel DRM CI has been intermittently reporting. This patch is a big
surgery for addressing the complexity and the possible unbalance.
Basically the patch changes the display PM in the following ways:
- Both HD-audio controller and codec drivers call a single helper,
snd_hdac_display_power(). (Formerly, the display power control from
a codec was done indirectly via link_power bus ops.)
- snd_hdac_display_power() receives the codec address index. For
turning on/off from the controller, pass HDA_CODEC_IDX_CONTROLLER.
- snd_hdac_display_power() doesn't manage refcounts any longer, but
keeps the power status in bitmap. If any of controller or codecs is
turned on, the function updates the DRM power state via get_power()
or put_power().
Also this refactor allows us more cleanup:
- The link_power bus ops is dropped, so there is no longer indirect
management, as mentioned in the above.
- hdac_device link_power_control flag is moved to hda_codec
display_power_control flag, as it's only for HDA legacy.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106525
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make unified suspend / resume helpers and call them from both the
runtime- and the system-PM callbacks for simplifying code.
There are slight changes of call orders, but there shouldn't be any
functional difference after refactoring.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's similar to other AMD audio devices, it also supports D3, which can
save some power drain.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power-saving is causing plops on audio start/stop on the built-in audio
of the nForce 430 based ASRock N68C-S UCC motherboard, add this model to
the power_save blacklist.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104
Cc: <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power-saving is causing plops on audio start/stop on Dell Precision T3600
laptops and Intel DZ77BH boards, add these to the power_save blacklist.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent change of vga_switcheroo allowed the runtime PM for
HD-audio on AMD GPUs, but this also resulted in a regression. When
the HD-audio controller driver gets runtime-suspended, HD-audio link
is turned off, and the hotplug notification is ignored. This leads to
the inconsistent audio state (the connection isn't notified and ELD is
ignored).
The best fix would be to implement the proper ELD notification via the
audio component, but it's still not ready. As a quick workaround,
this patch adds the check of runtime_idle and allows the runtime
suspend only when the vga_switcheroo is bound with discrete GPU.
That is, a system with a single GPU and APU would be again without
runtime PM to keep the HD-audio link for the hotplug notification and
ELD read out.
Also, the codec->auto_runtime_pm flag is set only for the discrete GPU
at the time GPU gets bound via vga_switcheroo (i.e. only dGPU is
forcibly runtime-PM enabled), so that APU can still get the ELD
notification.
For identifying which GPU is bound, a new vga_switcheroo client
callback, gpu_bound, is implemented. The vga_switcheroo simply calls
this when GPU is bound, and tells whether it's dGPU or APU.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200945
Fixes: 07f4f97d7b ("vga_switcheroo: Use device link for HDA controller")
Reported-by: Jian-Hong Pan <jian-hong@endlessm.com>
Tested-by: Jian-Hong Pan <jian-hong@endlessm.com>
Acked-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For easier sharing with ASoC.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluIAxkTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0NVNB/0cE/j09cyBR80x5gvnFE3Z5NEPNPLP
yl7sD93xFP6iww3CGJjXgxxDTh2sf7Sro4hcR9ZdD9zSSQ1qMVVY28MJ1YUsbFPu
TeUkqRFNPjgOpSmwK7T5QpVbIvdTZmmht8umgQ2+Y4vsGu1aKZf80ZT2n/2mjTOe
bEYfpyjP5V1aVL8JcX4TN3hbGZ2Pth5m404Qe0pkIdv4qqLx2edphJQ7ecU8w3kK
vTg1gfo7j9CKx7rzHZei/cvA3qXl/g9oufHAfpJDrlYFz6N35qwpA5UCyXqcFVo2
kZtyFbaBAvBjnhVyMNkdG7PvBMlL6HMLxN3fJbMLPPS30/+IuAsHXkZY
=wtBB
-----END PGP SIGNATURE-----
Merge tag 'hda-codec-h-move' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ALSA: Move hda_codec.h to include/sound
For easier sharing with ASoC.
As suggested by Takashi, move this header file to make it easier
to include from e.g. the Intel Skylake driver in follow-up patches
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the jackpoll_ms option value is passed indirectly by
referring to an array in chip->jackpoll_ms although each card needs to
see only the assigned value. Also, the sanity check is done at each
time in get_jackpoll_interval() although basically jackpoll_ms option
is a read-only, hence we need to evaluate only once at probe time.
This patch is the code simplification about the above points: the jack
polling interval is directly set to chip->jackpoll_interval so that it
can be simply copied to each codec.
No functional change but only code reduction.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since we dropped the memory page fiddling in the own allocators in
hda_intel.c, the substream allocation and free ops in both hda_intel.c
and hda_tegra.c became nothing but the simple calls of the standard
snd_pcm_lib helpers. As both are identical, there is no longer need
for indirect calls via ops; it's a good opportunity for removing ops
and simplifying the codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now the ALSA memory allocator helper supports the new non-cached
pages, let's use the new type, SNDRV_DMA_TYPE_DEV_UC_SG, for HD-audio
driver. This allows us to reduce lots of codes.
As another positive side-effect by this patch, the long-standing issue
with non-snoop mode playing in the non-mmap mode is fixed. The core
memalloc helper does the proper pgprot setup for non-cached pages for
vmap(), which was missing in the past.
Reported-and-tested-by: Hans Hu <HansHu@zhaoxin.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce a new flag, uc_buffer, to indicate that the controller
requires the non-cached pages for stream buffers, either as a
chip-specific requirement or specified via snoop=0 option.
This improves the code-readability.
Also, this patch fixes the incorrect behavior for C-Media chip where
the stream buffers were never handled as non-cached due to the check
of driver_type even if you pass snoop=0 option.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On modern laptop, there are more and more platforms
have two GPUs, and each of them maybe have audio codec
for HDMP/DP output. For some dGPU which is no output,
audio codec usually is disabled.
In currect HDA audio driver, it will set all codec as
VGA_SWITCHEROO_DIS, the audio which is binded to UMA
will be suspended if user use debugfs to contorl power
In HDA driver side, it is difficult to know which GPU
the audio has binded to. So set the bound gpu pci dev
to vga_switcheroo.
if the audio client is not the third registration, audio
id will set in vga_switcheroo enable function. if the
audio client is the last registration when vga_switcheroo
_ready() get true, we should get audio client id from bound
GPU directly.
Signed-off-by: Jim Qu <Jim.Qu@amd.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Except PCI_CLASS_DISPLAY_VGA, some PCI class is sometimes
PCI_CLASS_DISPLAY_3D or PCI_CLASS_DISPLAY_OTHER.
Signed-off-by: Jim Qu <Jim.Qu@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch can make audio controller in AMD Raven Ridge gets runtime
suspended to D3, to save ~1W power when it's not in use.
Cc: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power-saving is causing a humming sound when active on the Intel
NUC5i7RY, add it to the blacklist.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199607
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power-saving is causing plops on audio start/stop on ASRock H81M-HDS
machines, add these to the power_save blacklist.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power-saving is causing plops on audio start/stop on Gigabyte
P55A-UD3 and Gigabyte Z87-D3HP machines, add these to the power_save
blacklist.
Note these 2 boards both use 1458:a002 as subsystem ids, so they share
a single entry.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power-saving is causing a plop and silences the first 2 seconds
(give or take) of audio, silencing notifications sounds on Medion /
Clevo W35xSS_370SS laptops.
Add the Clevo W35xSS_370SS to the power_save blacklist.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1581607
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power-saving is causing a humming sound when active on the Intel
NUC7i3BNB, add it to the blacklist.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1520902
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power-saving is causing loud plops on the Lenovo C50 All in one, add it
to the blacklist.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1572975
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few small fixes:
- A fix for the NULL-dereference in rawmidi compat ioctls, triggered
by fuzzer
- HD-audio Realtek codec quirks, a VIA controller fixup
- A long-standing bug fix in LINE6 MIDI
-----BEGIN PGP SIGNATURE-----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=fb42
-----END PGP SIGNATURE-----
Merge tag 'sound-4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few small fixes:
- a fix for the NULL-dereference in rawmidi compat ioctls, triggered
by fuzzer
- HD-audio Realtek codec quirks, a VIA controller fixup
- a long-standing bug fix in LINE6 MIDI"
* tag 'sound-4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: rawmidi: Fix missing input substream checks in compat ioctls
ALSA: hda/realtek - adjust the location of one mic
ALSA: hda/realtek - set PINCFG_HEADSET_MIC to parse_flags
ALSA: hda - New VIA controller suppor no-snoop path
ALSA: line6: Use correct endpoint type for midi output
This patch is used to tell kernel that new VIA HDAC controller also
support no-snoop path.
[ minor coding style fix by tiwai ]
Signed-off-by: David Wang <davidwang@zhaoxin.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----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=WE2n
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.17-rc1' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"One omap, and one alsa pm fix (we merged the breaking patch via drm
tree).
Otherwise it's two bunches of amdgpu fixes, removing an unneeded file,
some DC fixes, HDMI audio regression fix, and some vega12 fixes"
* tag 'drm-fixes-for-v4.17-rc1' of git://people.freedesktop.org/~airlied/linux: (27 commits)
Revert "drm/amd/display: disable CRTCs with NULL FB on their primary plane (V2)"
Revert "drm/amd/display: fix dereferencing possible ERR_PTR()"
drm/amd/display: Fix regamma not affecting full-intensity color values
drm/amd/display: Fix FBC text console corruption
drm/amd/display: Only register backlight device if embedded panel connected
drm/amd/display: fix brightness level after resume from suspend
drm/amd/display: HDMI has no sound after Panel power off/on
drm/amdgpu: add MP1 and THM hw ip base reg offset
drm/amdgpu: fix null pointer panic with direct fw loading on gpu reset
drm/radeon: add PX quirk for Asus K73TK
drm/omap: fix crash if there's no video PLL
drm/amdgpu: Fix memory leaks at amdgpu_init() error path
drm/amdgpu: Fix PCIe lane width calculation
drm/radeon: Fix PCIe lane width calculation
drm/amdgpu/si: implement get/set pcie_lanes asic callback
drm/amdgpu: Add support for SRBM selection v3
Revert "drm/amdgpu: Don't change preferred domian when fallback GTT v5"
drm/amd/powerply: fix power reading on Fiji
drm/amd/powerplay: Enable ACG SS feature
drm/amdgpu/sdma: fix mask in emit_pipeline_sync
...
This became a large update. The changes are scattered widely,
and majority of them are attributed to ASoC componentization.
The gitk output made me dizzy, but it's slightly better than
London tube.
OK, below are some highlights:
- Continued hardening works in ALSA PCM core; most of the
existing syzkaller reports should have been covered.
- USB-audio got the initial USB Audio Class 3 support, as well
as UAC2 jack detection support and more DSD-device support.
- ASoC componentization: finally each individual driver was
converted to components framework, which is more future-proof
for further works. Most of conversations were systematic.
- Lots of fixes for Intel Baytrail / Cherrytrail devices with
Realtek codecs, typically tablets and small PCs.
- Fixes / cleanups for Samsung Odroid systems
- Cleanups in Freescale SSI driver
- New ASoC drivers:
* AKM AK4458 and AK5558 codecs
* A few AMD based machine drivers
* Intel Kabylake machine drivers
* Maxim MAX9759 codec
* Motorola CPCAP codec
* Socionext Uniphier SoCs
* TI PCM1789 and TDA7419 codecs
- Retirement of Blackfin drivers along with architecture removal.
-----BEGIN PGP SIGNATURE-----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=F3q1
-----END PGP SIGNATURE-----
Merge tag 'sound-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became a large update. The changes are scattered widely, and the
majority of them are attributed to ASoC componentization. The gitk
output made me dizzy, but it's slightly better than London tube.
OK, below are some highlights:
- Continued hardening works in ALSA PCM core; most of the existing
syzkaller reports should have been covered.
- USB-audio got the initial USB Audio Class 3 support, as well as
UAC2 jack detection support and more DSD-device support.
- ASoC componentization: finally each individual driver was converted
to components framework, which is more future-proof for further
works. Most of conversations were systematic.
- Lots of fixes for Intel Baytrail / Cherrytrail devices with Realtek
codecs, typically tablets and small PCs.
- Fixes / cleanups for Samsung Odroid systems
- Cleanups in Freescale SSI driver
- New ASoC drivers:
* AKM AK4458 and AK5558 codecs
* A few AMD based machine drivers
* Intel Kabylake machine drivers
* Maxim MAX9759 codec
* Motorola CPCAP codec
* Socionext Uniphier SoCs
* TI PCM1789 and TDA7419 codecs
- Retirement of Blackfin drivers along with architecture removal"
* tag 'sound-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (497 commits)
ALSA: pcm: Fix UAF at PCM release via PCM timer access
ALSA: usb-audio: silence a static checker warning
ASoC: tscs42xx: Remove owner assignment from i2c_driver
ASoC: mediatek: remove "simple-mfd" in the example
ASoC: cpcap: replace codec to component
ASoC: Intel: bytcr_rt5651: don't use codec anymore
ASoC: amd: don't use codec anymore
ALSA: usb-audio: fix memory leak on cval
ALSA: pcm: Fix mutex unbalance in OSS emulation ioctls
ASoC: topology: Fix kcontrol name string handling
ALSA: aloop: Mark paused device as inactive
ALSA: usb-audio: update clock valid control
ALSA: usb-audio: UAC2 jack detection
ALSA: pcm: Return -EBUSY for OSS ioctls changing busy streams
ALSA: pcm: Avoid potential races between OSS ioctls and read/write
ALSA: usb-audio: Integrate native DSD support for ITF-USB based DACs.
ALSA: usb-audio: FIX native DSD support for TEAC UD-501 DAC
ALSA: usb-audio: Add native DSD support for Luxman DA-06
ALSA: usb-audio: fix uac control query argument
ASoC: nau8824: recover system clock when device changes
...
The system sleep PM ops azx_suspend() and azx_resume() were previously
called by vga_switcheroo, but commit 07f4f97d7b ("vga_switcheroo: Use
device link for HDA controller") removed their invocation.
Unfortunately the commit neglected to update the #ifdef surrounding the
two functions, so if CONFIG_PM_SLEEP is *not* enabled but all three of
CONFIG_PM, CONFIG_VGA_SWITCHEROO and CONFIG_SND_HDA_CODEC_HDMI *are*
enabled, the compiler now emits the following warning:
sound/pci/hda/hda_intel.c:1024:12: warning: 'azx_resume' defined but not used [-Wunused-function]
static int azx_resume(struct device *dev)
^~~~~~~~~~
sound/pci/hda/hda_intel.c:989:12: warning: 'azx_suspend' defined but not used [-Wunused-function]
static int azx_suspend(struct device *dev)
^~~~~~~~~~~
Silence by updating the #ifdef. Because the #ifdef block now uses the
same condition as the one immediately succeeding it, the two blocks can
be collapsed together, shaving off another two lines.
Fixes: 07f4f97d7b ("vga_switcheroo: Use device link for HDA controller")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.kernel.org/patch/10313441/
Link: https://patchwork.freedesktop.org/patch/msgid/b8e70e34a9acbd4f0a1a6c7673cea96888ae9503.1522323444.git.lukas@wunner.de
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJauCZfAAoJEHm+PkMAQRiGWGUH/2rhdQDkoJpYWnjaQkolECG8
MxpGE7nmIIHxQcbSDdHTGJ8IhVm6Z5wZ7ym/PwCDTT043Y1y341sJrIwL2/nTG6d
HVidk8hFvgN6QzlzVAHT3ZZMII/V9Zt+VV5SUYLGnPAVuJNHo/6uzWlTU5g+NTFo
IquFDdQUaGBlkKqby+NoAFnkV1UAIkW0g22cfvPnlO5GMer0gusGyVNvVp7TNj3C
sqj4Hvt3RMDLMNe9RZ2pFTiOD096n8FWpYftZneUTxFImhRV3Jg5MaaYZm9SI3HW
tXrv/LChT/F1mi5Pkx6tkT5Hr8WvcrwDMJ4It1kom10RqWAgjxIR3CMm448ileY=
=YKUG
-----END PGP SIGNATURE-----
Backmerge tag 'v4.16-rc7' into drm-next
Linux 4.16-rc7
This was requested by Daniel, and things were getting
a bit hard to reconcile, most of the conflicts were
trivial though.
We've observed too long probe time with Coffee Lake (CFL) machines,
and the likely cause is some communication problem between the
HD-audio controller and the codec chips. While the controller expects
an IRQ wakeup for each codec response, it seems sometimes missing, and
it takes one second for the controller driver to time out and read the
response in the polling mode.
Although we aren't sure about the real culprit yet, in this patch, we
put a workaround by forcing the polling mode as default for CFL
machines; the polling mode itself isn't too heavy, and much better
than other workarounds initially suggested (e.g. disabling
power-save), at least.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199007
Fixes: e79b0006c4 ("ALSA: hda - Add Coffelake PCI ID")
Reported-and-tested-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Back in 2013, runtime PM for GPUs with integrated HDA controller was
introduced with commits 0d69704ae3 ("gpu/vga_switcheroo: add driver
control power feature. (v3)") and 246efa4a07 ("snd/hda: add runtime
suspend/resume on optimus support (v4)").
Briefly, the idea was that the HDA controller is forced on and off in
unison with the GPU.
The original code is mostly still in place even though it was never a
100% perfect solution: E.g. on access to the HDA controller, the GPU
is powered up via vga_switcheroo_runtime_resume_hdmi_audio() but there
are no provisions to keep it resumed until access to the HDA controller
has ceased: The GPU autosuspends after 5 seconds, rendering the HDA
controller inaccessible.
Additionally, a kludge is required when hda_intel.c probes: It has to
check whether the GPU is powered down (check_hdmi_disabled()) and defer
probing if so.
However in the meantime (in v4.10) the driver core has gained a feature
called device links which promises to solve such issues in a clean way:
It allows us to declare a dependency from the HDA controller (consumer)
to the GPU (supplier). The PM core then automagically ensures that the
GPU is runtime resumed as long as the HDA controller's ->probe hook is
executed and whenever the HDA controller is accessed.
By default, the HDA controller has a dependency on its parent, a PCIe
Root Port. Adding a device link creates another dependency on its
sibling:
PCIe Root Port
^ ^
| |
| |
HDA ===> GPU
The device link is not only used for runtime PM, it also guarantees that
on system sleep, the HDA controller suspends before the GPU and resumes
after the GPU, and on system shutdown the HDA controller's ->shutdown
hook is executed before the one of the GPU. It is a complete solution.
Using this functionality is as simple as calling device_link_add(),
which results in a dmesg entry like this:
pci 0000:01:00.1: Linked as a consumer to 0000:01:00.0
The code for the GPU-governed audio power management can thus be removed
(except where it's still needed for legacy manual power control).
The device link is added in a PCI quirk rather than in hda_intel.c.
It is therefore legal for the GPU to runtime suspend to D3cold even if
the HDA controller is not bound to a driver or if CONFIG_SND_HDA_INTEL
is not enabled, for accesses to the HDA controller will cause the GPU to
wake up regardless if they're occurring outside of hda_intel.c (think
config space readout via sysfs).
Contrary to the previous implementation, the HDA controller's power
state is now self-governed, rather than GPU-governed, whereas the GPU's
power state is no longer fully self-governed. (The HDA controller needs
to runtime suspend before the GPU can.)
It is thus crucial that runtime PM is always activated on the HDA
controller even if CONFIG_SND_HDA_POWER_SAVE_DEFAULT is set to 0 (which
is the default), lest the GPU stays awake. This is achieved by setting
the auto_runtime_pm flag on every codec and the AZX_DCAPS_PM_RUNTIME
flag on the HDA controller.
A side effect is that power consumption might be reduced if the GPU is
in use but the HDA controller is not, because the HDA controller is now
allowed to go to D3hot. Before, it was forced to stay in D0 as long as
the GPU was in use. (There is no reduction in power consumption on my
Nvidia GK107, but there might be on other chips.)
The code paths for legacy manual power control are adjusted such that
runtime PM is disabled during power off, thereby preventing the PM core
from resuming the HDA controller.
Note that the device link is not only added on vga_switcheroo capable
systems, but for *any* GPU with integrated HDA controller. The idea is
that the HDA controller streams audio via connectors located on the GPU,
so the GPU needs to be on for the HDA controller to do anything useful.
This commit implicitly fixes an unbalanced runtime PM ref upon unbind of
hda_intel.c: On ->probe, a runtime PM ref was previously released under
the condition "azx_has_pm_runtime(chip) || hda->use_vga_switcheroo", but
on ->remove a runtime PM ref was only acquired under the first of those
conditions. Thus, binding and unbinding the driver twice on a
vga_switcheroo capable system caused the runtime PM refcount to drop
below zero. The issue is resolved because the AZX_DCAPS_PM_RUNTIME flag
is now always set if use_vga_switcheroo is true.
For more information on device links please refer to:
https://www.kernel.org/doc/html/latest/driver-api/device_link.html
Documentation/driver-api/device_link.rst
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Kai Heng Feng <kai.heng.feng@canonical.com> # AMD PowerXpress
Tested-by: Mike Lothian <mike@fireburn.co.uk> # AMD PowerXpress
Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/51bd38360ff502a8c42b1ebf4405ee1d3f27118d.1520068884.git.lukas@wunner.de
Icelake is a next generation Intel platform. Add PCI ID for
it.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With the commit 1ba8f9d308 ("ALSA: hda: Add a power_save
blacklist"), we changed the default value of power_save option to -1
for processing the power-save blacklist.
Unfortunately, this seems breaking user-space applications that
actually read the power_save parameter value via sysfs and judge /
adjust the power-saving status. They see the value -1 as if the
power-save is turned off, although the actual value is taken from
CONFIG_SND_HDA_POWER_SAVE_DEFAULT and it can be a positive.
So, overall, passing -1 there was no good idea. Let's partially
revert it -- at least for power_save option default value is restored
again to CONFIG_SND_HDA_POWER_SAVE_DEFAULT. Meanwhile, in this patch,
we keep the blacklist behavior and make is adjustable via the new
option, pm_blacklist.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199073
Fixes: 1ba8f9d308 ("ALSA: hda: Add a power_save blacklist")
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some boards setting power_save to a non 0 value leads to clicking /
popping sounds when ever we enter/leave powersaving mode. Ideally we would
figure out how to avoid these sounds, but that is not always feasible.
This commit adds a blacklist for devices where powersaving is known to
cause problems and disables it on these devices.
Note I tried to put this blacklist in userspace first:
https://github.com/systemd/systemd/pull/8128
But the systemd maintainers rightfully pointed out that it would be
impossible to then later remove entries once we actually find a way to
make power-saving work on listed boards without issues. Having this list
in the kernel will allow removal of the blacklist entry in the same commit
which fixes the clicks / plops.
The blacklist only applies to the default power_save module-option value,
if a user explicitly sets the module-option then the blacklist is not
used.
[ added an ifdef CONFIG_PM for the build error -- tiwai]
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198611
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cannonlake is next generation Intel platform. This commit adds PCI ID for
it.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit dba9b7b6ca ("ALSA: hda - Fix doubly initialization of
i915 component") contained a typo that leads to the unbalance of i915
module reference. The value to be checked is not chip->driver_type
but chip->driver_caps.
Fixes: dba9b7b6ca ("ALSA: hda - Fix doubly initialization of i915 component")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196219
Reported-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the commit fcc88d91cd ("ALSA: hda - Bind with i915 component
before codec binding"), the binding with i915 audio component is moved
to be performed always at probing the controller. This fixed the
potential problems on IVB, but now it brought another issue on HSW and
BDW. These two platforms give two individual HD-audio controllers,
one for the analog codec on PCH and another for HDMI over gfx. Since
I decided to take a lazy path to check only AZX_DRIVER_PCH type in the
commit above, now both controllers try to bind with i915, and you see
a kernel WARNING.
This patch tries to address it again properly. Now a new DCAPS bit,
AZX_DCAPS_I915_COMPONENT, is introduced for indicating the binding
with i915 component in addition to the existing I915_POWERWELL bit
flag. Each PCI entry has to give this new flag if it requires the
binding with i915 component. For HSW/BDW PCH (i.e. the ones defined
by AZX_DCAPS_INTEL_PCH) doesn't contain AZX_DCAPS_I915_COMPONENT bit
while others have it.
While we're at it, add parentheses around the bit flag check for
avoiding possible compiler warnings, too.
The bug was spotted by Intel CI tests.
Fixes: fcc88d91cd ("ALSA: hda - Bind with i915 component before codec binding")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196219
Reported-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We used a on-demand i915 component binding for IvyBridge and
SandyBridge HDMI codecs, but it has a potential problem of the nested
module loading. For avoiding that situation, assure the i915 binding
happening at the controller driver level for PCH controller devices,
where the initialization is performed in a detached work, instead of
calling from the codec driver probe.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We checked the quirks specific to the recent Intel chips by checking
the PCI IDs manually, but it's becoming messy with lots of IS_SKL()
and other macros, as the amount accumulated.
For simplification, here the new AZX_DRIVER_SKL type is introduced,
and check chip->driver_type instead of the manual PCI ID. The short
name for this is still "HDA Intel PCH", so that it doesn't break the
existing user-space unnecessarily.
Suggested-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Broxton-T was a forgotten child and we didn't apply the quirks for
Skylake+ properly. Meanwhile, a quirk for reducing the DMA latency
seems specific to the early Broxton model, so we leave as is.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Coffelake is another Intel part, so need to add PCI ID for it.
Signed-off-by: Megha Dey <megha.dey@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
set_memory_* functions have moved to set_memory.h. Switch to this
explicitly.
Link: http://lkml.kernel.org/r/1488920133-27229-14-git-send-email-labbott@redhat.com
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some Intel platforms, the audio clock may not be set correctly
with initial setting. This will cause the audio playback/capture
rates wrong.
This patch checks the audio clock setting and will set it to a
proper value if it is set incorrectly.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188411
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Apply the same methods to obtain the current stream position as ASoC
Intel SKL driver uses. It reads the position from DPIB for a playback
stream while it still reads from the position buffer for a capture
stream. For a capture stream, some ugly workaround is needed to
settle down the inconsistent position.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Geminilake is another Intel part, so need to add PCI ID for it.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems that newer Intel chipsets have more than 15 I/O streams (total).
This patch forces the separate stream tags, when this hardware is detected
to avoid SDxCTL.STRM field overflow and an unexpected behaviour.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like for Sunrise Point, the total stream number of Lewisburg's
input and output stream exceeds 15 (GCAP is 0x9701), which will
cause some streams do not work because of the overflow on
SDxCTL.STRM field if using the legacy stream tag allocation method.
Fixes: 5cf92c8b3d ("ALSA: hda - Add Intel Lewisburg device IDs Audio")
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HD-audio driver has a mechanism to fall back to the single cmd mode as
a last resort if the CORB/RIRB communication goes wrong even after
switching to the polling mode. The switching has worked in the past
well, but Enrico Mioso reported that his system crashes when this
happens.
Although the actual cause of the crash isn't still fully analyzed yet,
it'd be in anyway good to provide an option to turn off the fallback
mode. Now this patch extends the behavior of the existing single_cmd
option for that. Namely,
- The option is changed from bool to bint.
- As default, it is the mode allowing the fallback to single cmd.
- Once when either true/false value is given to the option, the driver
explicitly turns on/off the single cmd mode, but without the
fallback.
That is, if you want to disable the fallback, just pass single_cmd=0
option. Passing single_cmd=1 will keep working like before.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Imre Deak reported a deadlock of HD-audio driver at unbinding while
it's still in probing. Since we probe the codecs asynchronously in a
work, the codec driver probe may still be kicked off while the
controller itself is being unbound. And, azx_remove() tries to
process all pending tasks via cancel_work_sync() for fixing the other
races (see commit [0b8c82190c12: ALSA: hda - Cancel probe work instead
of flush at remove]), now we may meet a bizarre deadlock:
Unbind snd_hda_intel via sysfs:
device_release_driver() ->
device_lock(snd_hda_intel) ->
azx_remove() ->
cancel_work_sync(azx_probe_work)
azx_probe_work():
codec driver probe() ->
__driver_attach() ->
device_lock(snd_hda_intel)
This deadlock is caused by the fact that both device_release_driver()
and driver_probe_device() take both the device and its parent locks at
the same time. The codec device sets the controller device as its
parent, and this lock is taken before the probe() callback is called,
while the controller remove() callback gets called also with the same
lock.
In this patch, as an ugly workaround, we unlock the controller device
temporarily during cancel_work_sync() call. The race against another
bind call should be still suppressed by the parent's device lock.
Reported-by: Imre Deak <imre.deak@intel.com>
Fixes: 0b8c82190c ("ALSA: hda - Cancel probe work instead of flush at remove")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 49d9e77e72 ("ALSA: hda - Fix system panic when DMA > 40 bits
for Nvidia audio controllers") simply disabled any DMA exceeding 32
bits for NVidia devices, even though they are capable of performing
DMA up to 40 bits. On some architectures (such as arm64), system memory
is not guaranteed to be 32-bit addressable by PCI devices, and so this
change prevents NVidia devices from working on platforms such as AMD
Seattle.
Since the original commit already mentioned that up to 40 bits of DMA
is supported, and given that the code has been updated in the meantime
to support a 40 bit DMA mask on other devices, revert commit 49d9e77e72
and explicitly set the DMA mask to 40 bits for NVidia devices.
Fixes: 49d9e77e72 ('ALSA: hda - Fix system panic when DMA > 40 bits...')
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For SKL and later Intel chips, we control the power well per codec
basis via link_power callback since the commit [03b135cebc47: ALSA:
hda - remove dependency on i915 power well for SKL].
However, there are a few exceptional cases where the gfx registers are
accessed from the audio driver: namely the wakeup override bit
toggling at (both system and runtime) resume. This seems causing a
kernel warning when accessed during the power well down (and likely
resulting in the bogus register accesses).
This patch puts the proper power up / down sequence around the resume
code so that the wakeup bit is fiddled properly while the power is
up. (The other callback, sync_audio_rate, is used only in the PCM
callback, so it's guaranteed in the power-on.)
Also, by this proper power up/down, the instantaneous flip of wakeup
bit in the resume callback that was introduced by the commit
[033ea349a7cd: ALSA: hda - Fix Skylake codec timeout] becomes
superfluous, as snd_hdac_display_power() already does it. So we can
clean it up together.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96214
Fixes: 03b135cebc ('ALSA: hda - remove dependency on i915 power well for SKL')
Cc: <stable@vger.kernel.org> # v4.2+
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Skylake onwards HDA controller supports new capabilities like
Global Time Stamping (GTS) capability. So add support to parse
these new capabilities.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This allows the device to correctly show up as ATI HDMI
rather than a generic one and allows the driver to use
the available caps.
Signed-off-by: Awais Belal <awais_belal@mentor.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
register_vga_switcheroo() sets the PM ops from the hda structure which
is freed later in azx_free. Make sure that these ops are cleared.
Caught by KASAN, initially noticed due to a general protection fault.
Fixes: 246efa4a07 ("snd/hda: add runtime suspend/resume on optimus support (v4)")
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kabylake-H shows up as PCI ID 0xa2f0. We missed adding this
earlier with other KBL IDs.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kabylake shows up as PCI ID 0xa171. And Kabylake-LP as 0x9d71.
Since these are similar to Skylake add these to SKL_PLUS macro
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent bug report suggests that BCLK setup for i915 HSW/BDW needs
to be updated at each HDMI hotplug, not only at initialization and
resume. That is, we need to update HSW_EM4 and HSW_EM5 registers at
ELD notification, too. Otherwise the HDMI audio may be out of sync
and played in a wrong pitch.
However, the HDA codec driver has no access to the controller
registers, and currently the code managing these registers is in
hda_intel.c, i.e. local to the controller driver. For allowing the
explicit BCLK update from the codec driver, as in this patch, the
former haswell_set_bclk() in hda_intel.c is moved to hdac_i915.c and
exposed as snd_hdac_i915_set_bclk(). This is called from both the HDA
controller driver and intel_pin_eld_notify() in HDMI codec driver.
Along with this change, snd_hdac_get_display_clk() gets dropped as
it's no longer used.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91410
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add HD Audio Device PCI ID for the Intel Broxton-T platform.
It is an HDA Intel PCH controller.
Signed-off-by: Lu, Han <han.lu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit fixes garbled audio on Polaris-10/11 variants
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some Skylake machines show the codec probe errors in certain
situations, e.g. HP Z240 desktop fails to probe the onboard Realtek
codec at reloading the snd-hda-intel module like:
snd_hda_intel 0000:00:1f.3: spurious response 0x200:0x2, last cmd=0x000000
snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to polling mode: lastcmd=0x000f0000
snd_hda_intel 0000:00:1f.3: No response from codec, disabling MSI: last cmd=0x000f0000
snd_hda_intel 0000:00:1f.3: Codec #0 probe error; disabling it...
hdaudio hdaudioC0D2: no AFG or MFG node found
snd_hda_intel 0000:00:1f.3: no codecs initialized
Also, HP G470 G3 suffers from the similar problem, as reported in
bugzilla below. On this machine, the codec probe error appears even
at a fresh boot.
As Libin suggested, the same workaround used for Broxton in the commit
[6639484ddaf6: ALSA: hda - disable dynamic clock gating on Broxton
before reset] can be applied for Skylake in order to fix this problem.
The Intel HW team also confirmed that this is needed for SKL.
This patch makes the workaround applied to both SKL and BXT
platforms. The referred macros are moved and one superfluous macro
(IS_BROXTON()) is another one (IS_BXT()) as well.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112731
Suggested-by: Libin Yang <libin.yang@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [991f86d7ae4e: ALSA: hda - Flush the pending probe work at
remove] introduced the sync of async probe work at remove for fixing
the race. However, this may lead to another hangup when the module
removal is performed quickly before starting the probe work, because
it issues flush_work() and it's blocked forever.
The workaround is to use cancel_work_sync() instead of flush_work()
there.
Fixes: 991f86d7ae ('ALSA: hda - Flush the pending probe work at remove')
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On Broxton, to make sure the reset controller works properly,
MISCBDCGE bit (bit 6) in CGCTL (0x48) of PCI configuration space
need be cleared before reset and set back to 1 after reset.
Otherwise, it may prevent the CORB/RIRB logic from being reset.
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As HD-audio driver does deferred probe internally via workqueue, the
driver might go into the mixed state doing both probe and remove when
the module gets unloaded during the probe work. This eventually
triggers an Oops, unsurprisingly.
For avoiding this race, we just need to flush the pending probe work
explicitly before actually starting the resource release.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=960710
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently HD-audio driver on Intel Skylake or Broxteon gives an error
message when binding with i915 audio component fails. However, this
isn't any serious error on a system without Intel graphics. Indeed
there are such systems, where a third-party codec (e.g. Creative) is
put on the mobo while using other discrete GPU (e.g. Nvidia).
Printing a kernel "error" message is overreaction in such a case.
This patch downgrades the print level for that message. For systems
that mandate the i915 binding (e.g. Haswell or Broadwell HDMI/DP),
another kernel error message is shown in addition to make clear what
went wrong.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111021
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the info in /proc/interrupts doesn't allow to figure out which
interrupt belongs to which card (HDMI, PCH, ..).
Therefore add card details to the interrupt description.
With the patch the info in /proc/interrupts looks like this:
PCI-MSI 442368-edge snd_hda_intel:card1
PCI-MSI 49152-edge snd_hda_intel:card0
NOTE: this patch adds the new irq_descr field snd_card struct that is
filled automatically at a card object creation. This can be used
generically for other drivers as well. The changes for others will
follow later -- tiwai
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It takes three minutes to enter into hibernation on some OEM SKL
machines and we see many codec spurious response after thaw() opertion.
This is because HDA is still in D0 state after freeze() call and
pci_pm_freeze/pci_pm_freeze_noirq() don't set D3 hot in pci_bus driver.
It seems bios still access HDA when system enter into freeze state,
HDA will receive codec response interrupt immediately after thaw() call.
Because of this unexpected interrupt, HDA enter into a abnormal
state and slow down the system enter into hibernation.
In this patch, we put HDA into D3 hot state in azx_freeze_noirq() and
put HDA into D0 state in azx_thaw_noirq().
V2: Only apply this fix to SKL+
Fix compile error when CONFIG_PM_SLEEP isn't defined
[Yet another fix for CONFIG_PM_SLEEP ifdef and the additional comment
by tiwai]
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AZX_DCAPS_POSFIX_VIA is coupled always with AZX_DRIVER_VIA type, so we
don't have to keep this bit in dcaps. Save one more!
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AZX_DCAPS_RIRB_DELAY is dedicated only for Nvidia and its purpose is
just to set a flag in bus. So it's better to be set in the toplevel
driver, either hda_intel.c or hda_tegra.c, instead of the common
hda_controller.c. This also allows us to strip this flag from dcaps,
so save one more bit there.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AZX_DCAPS_RIRB_PRE_DELAY is always tied with AZX_DCAPS_CTX_WORKAROUND,
which is Creative's XFi specific. So, we can replace it and reduce
one more bit free for DCAPS.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Intel Atom processors seem to have a problem at recording when
bdl_pos_adj is set to an odd value. When a value like 1 is used, it
may drop the samples unexpectedly. Actually, for the old Atoms, we
used to set AZX_DRIVER_SCH type, and this assigns 32 as default.
Meanwhile the newer chips, Baytrail and Braswell, are set as
AZX_DRIVER_PCH, and the lower default value, 1, is assigned.
This patch changes the default values for these chipsets to a safer
default, 32, again. Since changing the driver type (AZX_DRIVER_XXX)
leads to the rename of the driver string, it would result in a
possible regression. So, we can't change the type. Instead, in this
patch, manual (ugly) PCI ID checks are added on top.
A drawback by this increase is the slight increase of the latency, but
it's a sub-ms order in normal situations, so mostly negligible.
Reported-and-tested-by: Jochen Henneberg <jh@henneberg-systemdesign.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just a minor cleanup; instead of passing an array, pass the assigned
bdl_pos_adj option value directory in struct azx. Also split the code
to get the default bdl_pos_adj value for the change that will follow
after this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to the recent change, HDA controller driver for Intel PCH tries to
bind i915 audio component always at the probe time no matter whether
HDMI/DP codec is found. This is, however, superflulous for old
chipsets (e.g. on IVB) where they don't have always the HDMI/DP codecs
but often have only a discrete GPU instead.
For the newer chipsets, we need already the i915 binding from the
beginning due to power well control. Meanwhile, for older chipsets
where we don't need power well, we don't need the i915 binding at the
controller level.
This patch removes again the i915 binding in the HDA controller driver
for old Intel PCHs, but adds the binding in HDMI/DP codec driver
instead. This allows still the use of the direct notification from
the graphics driver while we can avoid the unnecessary load of i915
driver for machines only with another GPU.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent commit [6603249dcdbb: ALSA: hda - Enable audio component
for old Intel PCH devices] enabled the i915 binding for HDMI/DP on old
Intel PCHs. But many boards are without HDMI/DP, and they actually
don't need i915 binding, and yet the driver has a check of i915
binding and complains like
Haswell must be built with CONFIG_SND_HDA_I915
This error is false-positive, and it should be put only for HSW/BDW,
instead of all devices that may be bound with i915.
This patch fixes the condition to check, as well as rephrasing the
message specific to HSW/BDW HDMI/DP.
Fixes: 6603249dcd ('ALSA: hda - Enable audio component for old Intel PCH devices')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In BXT-P A0, HD-Audio DMA requests is later than expected,
and makes an audio stream sensitive to system latencies when
24/32 bits are playing.
Adjusting threshold of DMA fifo to force the DMA request
sooner to improve latency tolerance at the expense of power.
v2: move Intel specific code to hda_intel.c
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As i915 graphics driver provides the notification via audio component,
not only the currently implemented HSW+ and VLV+ platforms but also
all other PCH-based platforms (e.g. Cougar Point, Panther Point, etc)
can use this infrastructure. It'll improve the reliability and the
power consumption significantly, especially once when we implement the
ELD notification via component. As a preliminary, this patch enables
the usage of audio component for all PCH platforms.
The HDA controller just needs to set AZX_DCAPS_I915_POWERWELL flag
appropriately. The name of the flag is a bit confusing, but this
actually works even on the chips without the powerwell but accesses
only the other component ops.
In the HDMI/DP codec driver side, we just need to register/unregister
the notifier for such chips. This can be identified by checking the
audio_component field in the assigned hdac_bus.
One caveat is that PCH for Haswell and Broadwell must not be bound
with i915 audio component, as there are dedicated HD-audio HDMI
controllers on these platforms. Ditto for Poulsbo and Oaktrail as
they use gma500 graphics, not i915.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Quite a large batch of fixes have come in since the merge window, mainly
driver specific ones but there's a couple of core ones:
- A fix for DAPM resume on active streams to ensure everything ends up
cleanly in the right state.
- Reset the DAPM cache when freeing widgets to fix a crash on driver
remove and reload.
The PM functions for nau8825 are new code which fix crashes on resume.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWWE13AAoJECTWi3JdVIfQF+wH/3D0Asc5rVdU81cxaxdjgGxJ
WUGUCJ+4D1HTtZQf8MouwFqMvDK+lOKiPkAzMdyk3NQG50S0XtMD8xM7JeglPZ1L
U7ro6EfYqGmkMyqClVxWnJMBnGoTiLrAftFlIBFPaQ6FDdfMMlNcK2Y4hCs/t3y7
A5T0LlqKdz++bKQRoq0zpiWWSnfoaEub25IaEB97k9sjlr9rRTR1UwHibHdm3JGg
vzkqLTaH/zm1VgR70jH6XnQSN8KtIdrx/u2ZWJZVqfioMTMFYIboufcwDWqX4oNA
vqcYjzfCyhDaMnVYpI+7ettHfXn3iBR3VykXIOI1uzM63N5f1IK7bOwPRxiMXAA=
=CDO8
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.4
Quite a large batch of fixes have come in since the merge window, mainly
driver specific ones but there's a couple of core ones:
- A fix for DAPM resume on active streams to ensure everything ends up
cleanly in the right state.
- Reset the DAPM cache when freeing widgets to fix a crash on driver
remove and reload.
The PM functions for nau8825 are new code which fix crashes on resume.
Add HD Audio Device PCI ID for the Intel Broxton platform.
It is an HDA Intel PCH controller.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull drm updates from Dave Airlie:
"I Was Almost Tempted To Capitalise Every Word, but then I decided I
couldn't read it myself!
I've also got one pull request for the sti driver outstanding. It
relied on a commit in Greg's tree and I didn't find out in time, that
commit is in your tree now so I might send that along once this is
merged.
I also had the accidental misfortune to have access to a Skylake on my
desk for a few days, and I've had to encourage Intel to try harder,
which seems to be happening now.
Here is the main drm-next pull request for 4.4.
Highlights:
New driver:
vc4 driver for the Rasberry Pi VPU.
(From Eric Anholt at Broadcom.)
Core:
Atomic fbdev support
Atomic helpers for runtime pm
dp/aux i2c STATUS_UPDATE handling
struct_mutex usage cleanups.
Generic of probing support.
Documentation:
Kerneldoc for VGA switcheroo code.
Rename to gpu instead of drm to reflect scope.
i915:
Skylake GuC firmware fixes
HPD A support
VBT backlight fallbacks
Fastboot by default for some systems
FBC work
BXT/SKL workarounds
Skylake deeper sleep state fixes
amdgpu:
Enable GPU scheduler by default
New atombios opcodes
GPUVM debugging options
Stoney support.
Fencing cleanups.
radeon:
More efficient CS checking
nouveau:
gk20a instance memory handling improvements.
Improved PGOB detection and GK107 support
Kepler GDDR5 PLL statbility improvement
G8x/GT2xx reclock improvements
new userspace API compatiblity fixes.
virtio-gpu:
Add 3D support - qemu 2.5 has it merged for it's gtk backend.
msm:
Initial msm88896 (snapdragon 8200)
exynos:
HDMI cleanups
Enable mixer driver byt default
Add DECON-TV support
vmwgfx:
Move to using memremap + fixes.
rcar-du:
Add support for R8A7793/4 DU
armada:
Remove support for non-component mode
Improved plane handling
Power savings while in DPMS off.
tda998x:
Remove unused slave encoder support
Use more HDMI helpers
Fix EDID read handling
dwhdmi:
Interlace video mode support for ipu-v3/dw_hdmi
Hotplug state fixes
Audio driver integration
imx:
More color formats support.
tegra:
Minor fixes/improvements"
[ Merge fixup: remove unused variable 'dev' that had all uses removed in
commit 4e270f088011: "drm/gem: Drop struct_mutex requirement from
drm_gem_mmap_obj" ]
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (764 commits)
drm/vmwgfx: Relax irq locking somewhat
drm/vmwgfx: Properly flush cursor updates and page-flips
drm/i915/skl: disable display side power well support for now
drm/i915: Extend DSL readout fix to BDW and SKL.
drm/i915: Do graphics device reset under forcewake
drm/i915: Skip fence installation for objects with rotated views (v4)
vga_switcheroo: Drop client power state VGA_SWITCHEROO_INIT
drm/amdgpu: group together common fence implementation
drm/amdgpu: remove AMDGPU_FENCE_OWNER_MOVE
drm/amdgpu: remove now unused fence functions
drm/amdgpu: fix fence fallback check
drm/amdgpu: fix stoping the scheduler timeout
drm/amdgpu: cleanup on error in amdgpu_cs_ioctl()
drm/i915: Fix locking around GuC firmware load
drm/amdgpu: update Fiji's Golden setting
drm/amdgpu: update Fiji's rev id
drm/amdgpu: extract common code in vi_common_early_init
drm/amd/scheduler: don't oops on failure to load
drm/amdgpu: don't oops on failure to load (v2)
drm/amdgpu: don't VT switch on suspend
...
Adding Intel codename Lewisburg platform device IDs for audio.
[rearranged the position by tiwai]
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've had many reports that some Creative sound cards with CA0132
don't work well. Some reported that it starts working after reloading
the module, while some reported it starts working when a 32bit kernel
is used. All these facts seem implying that the chip fails to
communicate when the buffer is located in 64bit address.
This patch addresses these issues by just adding AZX_DCAPS_NO_64BIT
flag to the corresponding PCI entries. I casually had a chance to
test an SB Recon3D board, and indeed this seems helping.
Although this hasn't been tested on all Creative devices, it's safer
to assume that this restriction applies to the rest of them, too. So
the flag is applied to all Creative entries.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently everyone and their dog has their own favourite spelling
for vga_switcheroo. This makes it hard to grep dmesg for log entries
relating to vga_switcheroo. It also makes it hard to find related
source files in the tree.
vga_switcheroo.c uses pr_fmt "vga_switcheroo". Use that everywhere.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: http://patchwork.freedesktop.org/patch/msgid/9b0175319ce78d831acfcf11e4c6c760f826b0e3.1444663039.git.lukas@wunner.de
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The active attribute in struct vga_switcheroo_client denotes whether
the outputs are currently switched to this client. The attribute is
only meaningful for vga clients. It is never used for audio clients.
The function vga_switcheroo_register_audio_client() misuses this
attribute to store whether the audio device is fully initialized.
Most likely there was a misunderstanding about the meaning of
"active" when this was added.
Comment from Takashi's review:
"Not really. The full initialization of audio was meant that the audio
is active indeed. Admittedly, though, the active flag for each audio
client doesn't play any role because the audio always follows the gfx
state changes, and the value passed there doesn't reflect the actual
state due to the later change. So, I agree with the removal of the
flag itself -- or let the audio active flag following the
corresponding gfx flag. The latter will make the proc output more
consistent while the former is certainly more reduction of code."
Set the active attribute to false for audio clients. Remove the
active parameter from vga_switcheroo_register_audio_client() and
its sole caller, hda_intel.c:register_vga_switcheroo().
vga_switcheroo_register_audio_client() was introduced by 3e9e63dbd3
("vga_switcheroo: Add the support for audio clients"). Its use in
hda_intel.c was introduced by a82d51ed24 ("ALSA: hda - Support
VGA-switcheroo").
v1.1: The changes above imply that in find_active_client() the call
to client_is_vga() is now superfluous. Drop it.
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
[danvet: Add Takashi's clarification to the commit message.]
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PM ops could be triggered before HDA is done initializing
and cause PM to set HDA controller to D3Hot. This can result
in "CORB reset timeout#2, CORBRP = 65535" and "no codecs
initialized". Additionally, PM ops can be triggered before
azx_probe_continue finishes (async probe). This can result
in a NULL deref kernel crash.
To fix this, avoid PM ops if !chip->running.
Signed-off-by: U. Artie Eoff <ullysses.a.eoff@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A lot of small fixes here, a few to the core:
- Fix for binding DAPM stream widgets on devices with prefixes assigned
to them
- Minor fixes for the newly added topology interfaces
- Locking and memory leak fixes for DAPM
- Driver specific fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVsnNFAAoJECTWi3JdVIfQH9cH/1ddueDFikvXSCyntuJcHAwJ
a7X5kCVdegMnaMK5fnAbTlJBpDIX/F1UBvsFQQ38eKWeneP44XnkXeh/32fGJzQO
L730dqy0tkgQdWJkQg0yxaP5/k0BfhnXeRc3ATUG3LBgUBrWRYLTIvaM+G+H3Kf5
K88QL7cKmeY0Kt6+cms3nnBj9x5oFgbHIW7Y3K/pza+XPVecZ7N3/5gpV+VQDUXh
Oz3cZOsC5h4+IpxkOrLXY7zgLvrt/HfRTO2QF/3Ntub81anAk190pVAquM+r/CTn
tQ3sPNGLglQ4VRXNP6yBKJOp5CUTBLt5XWlJ+Kg9p2OiiuOPla4wkhuGDS5AM64=
=nJJl
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.2
A lot of small fixes here, a few to the core:
- Fix for binding DAPM stream widgets on devices with prefixes assigned
to them
- Minor fixes for the newly added topology interfaces
- Locking and memory leak fixes for DAPM
- Driver specific fixes
When the controller is powered up but the HDMI codec is powered down
on Skylake, the power well is turned off. When the codec is then
powered up again, we need to poke the codec a little extra to make
sure it wakes up. Otherwise we'll get sad "no response from codec"
messages and broken audio.
This also changes azx_runtime_resume to actually call
snd_hdac_set_codec_wakeup for Skylake (before STATETS read).
(Otherwise it would only have been called for Haswell and Broadwell,
which both do not need it, so this probably was not the author's
intention.)
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here are a bunch of small fixes, mostly for HD-audio quirks, in
addition to a few regression fixes and trivial cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=DOli
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a bunch of small fixes, mostly for HD-audio quirks, in
addition to a few regression fixes and trivial cleanups"
* tag 'sound-fix-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: Fix uninintialized error return
ALSA: hda: Delete an unnecessary check before the function call "snd_info_free_entry"
ALSA: hda - Add a fixup for Dell E7450
ALSA: hda - Fix the dock headphone output on Fujitsu Lifebook E780
ALSA: hda - Add headset support to Acer Aspire V5
ALSA: hda - restore the MIC FIXUP for some Dell machines
ALSA: jack: Fix endless loop at unique index detection
ALSA: hda - set proper caps for newer AMD hda audio in KB/KV
ALSA: hda - Disable widget power-save for VIA codecs
ALSA: hda - Fix Dock Headphone on Thinkpad X250 seen as a Line Out
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
The previous patch tried to continue the probe if i915 binding fails.
For for simplicity reason, we haven't implemented abort even for
controller chips that are dedicated for HDMI/DP on HSW and BDW.
However, Mengdong suggested that this can be dangerous; BIOS may
disable gfx power well although the PCI entry for HD-audio is left,
and this may result in the unexpected behavior, kernel errors, etc.
For avoiding this situation, abort the probe at i915 binding failure
only for HSW/BDW chips selectively. For other chips, it still
continues.
Fixes: bf06848bdb ('ALSA: hda - Continue probing even if i915 binding fails')
Reported-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This merges and resolves the non-trivial conflicts with the recent fix
for hda-i915 binding fallback.
Conflicts:
sound/pci/hda/hda_intel.c
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently snd-hda-intel driver aborts the probing of Intel HD-audio
controller with i915 power well management when binding with i915
driver via hda_i915_init() fails. This is no big problem for Haswell
and Broadwell where the HD-audio controllers are dedicated to
HDMI/DP, thus i915 link is mandatory. However, Skylake, Baytrail and
Braswell have only one controller and both HDMI/DP and analog codecs
share the same bus. Thus, even if HDMI/DP isn't usable, we should
keep the controller working for other codecs.
For fixing this, this patch simply allows continuing the probing even
if hda_i915_init() call fails. This may leave stale sound components
for HDMI/DP devices that are unbound with graphics. We could abort
the probing selectively, but from the code simplicity POV, it's better
to continue in all cases.
Reported-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For SKL, only the HDMI codec is in the display power well while the
HD-A controller isn't. So the controller flag 'need_i915_power' is
not set to release the display power after probe, and the codec flag
'link_power_control' is set to request/release the display power via
bus link_power ops.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A new AMD controller [1002:aac8] seems to need the quirk for other AMD
NS HDMI stuff, otherwise it gives noisy sounds.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99021
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The file is moved to hda core and renamed to hdac_i915.c, so can be used
by both legacy HDA driver and new Skylake audio driver.
- Add snd_hdac_ prefix to the public APIs.
- The i915 audio component is moved to core bus and dynamically allocated.
- A static pointer hdac_acomp is used to help bind/unbind callbacks to get
this component, because the sound card's private_data is used by the azx
chip pointer, which is a legacy structure. It could be removed if private
_data changes to some core structure which can be extended to find the
bus.
- snd_hdac_get_display_clk() is added to get the display core clock for
HSW/BDW.
- haswell_set_bclk() is moved to hda_intel.c because it needs to write the
controller registers EM4/EM5, and only legacy HD-A needs it for HSW/BDW.
- Move definition of HSW/BDW-specific registers EM4/EM5 to hda_register.h
and rename them to HSW_EM4/HSW_EM5, because other HD-A controllers have
different layout for the extended mode registers.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch creates hda_intel_trace.h to add some pm trace functions
used in hda_intel.c
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In SKL, HDMI/DP codec and PCH HD Audio Controller are in different power wells,
so it's necessary to reset display audio codecs when power well on, otherwise
display audio codecs will disappear when resume from low power state.
Reset steps when power on:
enable codec wakeup -> azx_init_chip() -> disable codec wakeup
The callback for codec wakeup enable/disable is in drivers/gpu/drm/i915/.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We're providing dummy functions for CONFIG_SND_HDA_i915=n, thus ifdef
can be reduced. (But hda_i915_init() has to be fixed to return zero.)
This automatically fixes a compile warning:
sound/pci/hda/hda_intel.c: In function 'azx_probe_continue':
sound/pci/hda/hda_intel.c:1966:1: warning: label 'i915_power_fail' defined but not used [-Wunused-label]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Baytrail (Valleyview) and Braswell (Cherryview), only the HDMI codec is
in the display power well while the HD-A controller isn't. So the controller
flag 'need_i915_power' is not set to release the display power after probe,
and the codec flag 'link_power_control" is set to request/release the display
power via bus link_power ops.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch can improve power saving for Intel platforms on which only the
display audio codec is in the shared i915 power well:
- Add a flag "need_i915_power" to indicate whether the controller needs the
i915 power well.
- The driver will always request the i915 power when probing the controller
and codecs if AZX_DCAPS_I915_POWERWELL is set (either the controller or a
codec needs this power).
- If the controller needs the i915 power, the power will be held after probe
until the controller is runtime suspended or S3. If the controller doesn't
need the power, the power will be released the after probe, and a codec
that needs the power can request/release the power via bus link_power ops.
Background:
- For Haswell/Broadwell, which has a separate HD-A controller for display audio,
both the controller and the display codec are in the i915 power well.
- For Baytrail/Braswell, the display and analog audio share the same HDA
controller and link, and only the display codec is in the i915 power well.
- For Skylake, the display and analog audio share the same HDA controller but
use separate links. Only the display codec is in the i915 power well. And in
legacy mode we take the two links as one. So it can follow Baytrail/Braswell.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch implements the bus link_power ops to request/release i915 display
power well. It can be used by the display codec which shares this power well
with GPU on Intel platforms.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch addes AZX_DCAPS_I915_POWERWELL to BYT (Baytrail).
Like Braswell and Skylake, the HDMI codec on Bytrail is also in the shared
power well with GPU. This power well must be turned on before we reset link
to probe the codec, to avoid communication failure with the codec.
The side effect is that this power is always ON in S0 because the BYT HDMI
codec does not support EPSS or D3ClkStop and so the controller doesn't enter
D3 at runtime, and the HDMI codec and analog codec share a single physical
HD-A link and so we cannot reset the HD-A link freely when we re-enable the
power to use the HDMI codec.
Next step is to test if an AGP reset or double AGP reset on BYT HDMI codec is
okay to bring the HDMI codec back to a functional state after restoring the
power. If okay, we can bind the power on/off with the HDMI codec PM without
interrupting the analog audio.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... and replace with the existing hda-core helper codes.
This reduces lots of lines, finally.
Since struct hda_bus is now embedded into struct azx,
snd_hda_bus_new() is moved and expanded from hda_codec.c to
hda_controller.c, accordingly. Also private_free bus ops and
private_data field are removed because we no longer need to point azx
object from bus (we can use container_of())
The spin locks are consolidated into the single one, bus->reg_lock.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Embed hdac_stream object into azx_dev, and use a few basic helper
functions. The most of helper codes for hdac_stream aren't still used
yet.
Also this commit disables the tracepoints temporarily due to build
problems. It'll be enabled again later.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
One less redirection again. This also requires the change of the call
order in the toplevel divers. Namely, the bus has to be created at
first before other initializations since the memory allocation ops are
called through bus object now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDMI/DP codec on SKL/BSW is in the power well.
The power well must be turned on before probing the
HDMI/DP codec.
This is a temporary patch, which will power on the
powerwell by adding AZX_DCAPS_I915_POWERWELL for SKL
and BSW. After restructuring and new flag is added,
this patch will be reverted.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The total stream number of Sunrise Point's input and output stream
exceeds 15, which will cause some streams do not work because
of the overflow on SDxCTL.STRM field if using the legacy
stream tag allocation method.
This patch uses the new stream tag allocation method by add
the flag AZX_DCAPS_SEPARATE_STREAM_TAG for Skylake platform.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few basic codes for communicating over HD-audio bus are moved to
struct hdac_bus now. It has only command and get_response ops in
addition to the unsolicited event handling.
Note that the codec-side tracing support is disabled temporarily
during this transition due to the code shuffling. It will be
re-enabled later once when all pieces are settled down.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver shutdown ops is simpler than registering reboot notifier
manually. There should be no functional change by this -- the codec
driver calls its own callback while the bus driver just calls
azx_stop() like before.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU960DAAoJECTWi3JdVIfQkKIH/RDvxRn8dvKOPF5U9Uix3chH
JWKkzqfsMP0EpmQTzCQPp0ShAyYcWSbYsopicynPxUem5vS4Z8+UmOgEEgkj59pK
USbF6v1jCQXA6BcbKyUcRRBD9FtRkfVDc7mYbRs2CcwQz2CGCgee41cvPM+2BT+z
QdNC9UJARSweGvE1IUJSfpfYOly+BJ2s0/28RaQ0PGt+I0auoYx7IMFgMSDjv2p6
PY0kyQiwm3Kyj2uNXPZ5gEuPxlw/t8n4fbQNrBYAvxzN+EF5NrGdKE3N7MI1xRV/
EkFhzy+uM3X9c37tb2lT2fgPFlBc9rgPuLPSyoQ6nxa5ghCqAlgRhzpxRem8hhU=
=VlCw
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Changes for v4.1
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
The events that are handled by HD-audio drivers are no frequent and
urgent ones, so we can use the standard workqueue without any problem
nowadays.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This makes the code flow easier -- instead of the controller driver
calling snd_hda_build_pcms() and snd_hda_build_controls() explicitly,
the codec driver itself builds PCMs and controls at probe time. Then
the controller driver only needs to call snd_card_register().
Also, this allows us the full bind/unbind control, too. Even when a
codec driver is bound later, it automatically registers the new PCM
and controls by itself.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The memory allocators should have already given the kernel warning
messages, thus we don't have to annoy again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, we let the controller driver power down the all codecs at the
end of probe. But this can be done better in the codec's dev_register
callback. This results in the reduction of duplicated codes in each
control driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now the final bit of runtime PM cleanup: instead of manual
notification of the power up/down of the codec via hda_bus pm_notify
ops, use the standard runtime PM feature.
The child codec device will kick off the runtime PM of the parent
(PCI) device upon suspend/resume automatically. For managing whether
the link can be really turned off, we use the bit flags
bus->codec_powered instead of the earlier bus->power_keep_link_on.
flag. Each codec driver is responsible to set/clear the bit flag, and
the controller device can be turned off only when all these bits are
cleared.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We used to pass the power_save option value to hda_bus via a given
pointer. This was needed to refer to the value from the HD-audio core
side. However, after the transition to the runtime PM, this is no
longer needed.
This patch drops the power_save value indirection in hda_bus above,
and let the controller driver reprograms the autosuspend value
explicitly by a new helper, snd_hda_set_power_save(). Without this
call, the HD-audio core doesn't set up the autosuspend and flip the
runtime PM. (User may still be able to set up via sysfs, though.)
Along with this change, the pointer argument of azx_bus_create() is
dropped as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is essentially a partial revert of the commit [b1920c21102a:
'ALSA: hda - Enable runtime PM on Panther Point']. There was a bug
report showing the HD-audio bus hang during runtime PM on HP Spectre
XT.
Reported-by: Dang Sananikone <dang.sananikone@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous transition of suspend/resume, now move the
power-save code to the standard runtime PM. As usual for runtime PM,
it's a bit tricky, but this simplified codes a lot in the end.
For keeping the usage compatibility, power_save module option still
controls the whole power-saving behavior on all codecs. The value is
translated to pm_runtime_*_autosuspend() and pm_runtime_allow() /
pm_runtime_forbid() calls.
snd_hda_power_up() and snd_hda_power_down() are translated to
pm_runtime_get_sync() and pm_runtime_put_autosuspend(), respectively.
Since we can do call pm_runtime_get_sync() more reliably, the sync
version is used always and snd_hda_power_up_d3wait() is dropped.
Another slight difference is that snd_hda_power_up()/down() don't call
runtime_pm code during the suspend/resume transition phase. Calling
them there isn't safe unlike our own code, resulted in unexpected
behavior (endless wakeups).
The hda_power_count tracepoint was removed, as it doesn't match well
with the new code.
Last but not least, we need to set ignore_children flag in the parent
dev.power field so that the runtime PM of the controller chip won't
get confused. The notification is still done in the bus pm_notify
callback. We'll get rid of this hack in the later patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch moves the suspend/resume mechanisms down to each codec
driver level, as we have a proper codec driver bound on the bus now.
Then we get the asynchronous PM gratis without fiddling much in the
driver level.
As a soft-landing transition, implement the common suspend/resume pm
ops for hda_codec_driver and keep the each codec driver intact. Only
the callers of suspend/resume in the controller side (azx_suspend()
and azx_resume()) are removed.
Another involved place is azx_bus_reset() calling the temporary
suspend and resume as a hackish method of bus reset. The HD-audio
core provide a helper function snd_hda_bus_reset() instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
azx_create_codec() function does actually two things: create a bus and
probe codecs. For the future work, split this to two logical
functions, azx_bus_create() and azx_probe_codecs().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For making the debugging of runtime PM easier, introduce
azx_has_pm_runtime() and use it in all places checking the runtime pm
driver capability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Register a component master to be used to interface with the i915
driver. This is meant to replace the current interface which is based on
module symbol lookups.
Note that currently we keep the existing behavior and pin the i915
module while the hda driver is loaded. Using the component interface
allows us to remove this dependency once support for dynamically
enabling / disabling the HDMI functionality is added to the driver.
v2:
- change roles between the hda and i915 components (Daniel)
v3:
- rename display_component to audio_component (Daniel)
v4:
- move removal of i915_powerwell.h from this patch to the next (Takashi)
- request_module fails if module support isn't enabled, so ignore
any error it returns and depend on the following NULL check of the
component ops (Takashi)
- change over to using dev_* instead of pr_* (Takashi)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
chip is already passed to most of the i915 interface functions. Unify
the interface by passing intel_hda instead of chip and passing it to all
functions. Passing intel_hda instead of chip makes more sense since this
is an intel specific interface. Also in an upcoming patch we will use
intel_hda in all of these functions so by passing intel_hda we can save
on some pointer casts from chip to intel_hda.
This will be needed by an upcoming patch adding component support.
No functional change.
v2-3: unchanged
v4:
- pass intel_hda instead of chip
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This struct will be needed by the component code added in an upcoming
patch, so export it into a new hda_intel.h file. At the same time also
merge hda_i915.h into this new header, there is no reason to keep two
separate intel specific header file.
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a similar cleanup like the commit [3db084fd0af5: ALSA: fm801:
PCI core handles power state for us].
Since pci_set_power_state(), pci_save_state() and pci_restore_state()
are already done in the PCI core side, so we don't need to it doubly.
Also, pci_enable_device(), pci_disable_device() and pci_set_master()
calls in PM callbacks are superfluous nowadays, too, so get rid of
them as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The iounmap() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The total stream number of Skylake's input and output stream
exceeds 15, which will cause some streams do not work because
of the overflow on SDxCTL.STRM field if using the legacy
stream tag allocation method.
This patch uses the new stream tag allocation method by add
the flag AZX_DCAPS_SEPARATE_STREAM_TAG for Skylake platform.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under sound/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
We introduced AZX_DCAPS_ALIGN_BUFSIZE to explicity show that the
controller needs the alignment, with a slight hope that the buffer
size alignment will be disabled as default in future. But the reality
tells that most chips need the buffer size alignment, and it'll be
likely enabled in future, too.
This patch drops AZX_DCAPS_ALIGN_BUFSIZE to give back one more
precious DCAPS bit for future use. At the same time, rename
AZX_DCAPS_BUFSIZE with AZX_DCAPS_NO_ALIGN_BUFSIZE for avoiding
confusion.
AZX_DCAPS_ALIGN_BUFSIZE are still kept (but commented out) in each
DCAPS presets for a purpose as markers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUe7l9AAoJEHm+PkMAQRiGkGcIAIryQ7NKn4IaxUtS807Lx4Ih
obEnx7nNKZTXCZpD/7XQGHMMJyozMJR50PHZESJoHu4Luhv9h7EFRnyJ6MdqMlwn
zla3zY0yRsHwPoJKcHbSE0CPHZz0WPQHj7IEbM+XJz2tMNJfbgTrezElmcCM4DRp
c9ae+ggwZ2cyNYM0r2RSwSJ525WMh69f9dzSUE27fpvkllQgwqNs/jHYz8HNOEht
FWcv5UhvzKjwJS3awULfOB3zH2QdFvVTrwAzd+kbV2Q6T6CaUoFRlhXeKUO6W2Jv
pJM6oj8tMZUkdXEv7EQXT1kwEqC4DULTTTHs4tSF79O1ESmNfePiOwwBcwoM2nM=
=kG1Y
-----END PGP SIGNATURE-----
Merge tag 'v3.18-rc7' into for-next
... for allowing more cleanups of hda_intel.c driver-caps where both
upstream and for-next contain the changes.
User can pass snoop option to enable/disable the snoop behavior, but
currently azx_check_snoop_available() always turns it off for some
devices. For better debuggability, change the parameter as bint, and
allow user to enable/disable forcibly the snoop when specified via the
module option.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new driver_caps bit, AZX_DCAPS_SNOOP_OFF, to set the snoop off
as default. This new bit is used for the checks in
azx_check_snoop_available(). Most of case-switches are replaced with
the new dcaps in each entry.
While working on it, for avoiding to spend more bits, combine three
bits AZX_DCAPS_SNOOP_SCH, AZX_DCAPS_SNOOP_ATI and
AZX_DCAPS_SNOOP_NVIDIA bits into a flat type of two bits. This
reduces the bits usages, and assign AZX_DCAPS_OFF to this empty bit
now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A number of radeon cards have a HW limitation causing them to be
unable to generate the full 64-bit of address bits for MSIs. This
breaks MSIs on some platforms such as POWER machines.
We used to have a powerpc specific quirk to address that on a
single card, but this doesn't scale very well, this is better
put under control of the drivers who know precisely what a given
HW revision can do.
We now have a generic quirk in the PCI code. We should set it
appropriately for all radeon's from the audio driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
CC: <stable@vger.kernel.org>
AMD/ATI HDMI controller chip models, we already have a filter to lower
to 32bit DMA, but the rest are supposed to be working with 64bit
although the hardware doesn't really work with 63bit but only with 40
or 48bit DMA. In this patch, we take 40bit DMA for safety for the
AMD/ATI controllers as the graphics drivers does.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
The functions kfree() and release_firmware() test whether their argument
is NULL and then return immediately. Thus the test around the call
is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CMI8888 shows the stuttering playback when the snooping is disabled
on the audio buffer. Meanwhile, we've got reports that CORB/RIRB
doesn't work in the snooped mode. So, as a compromise, disable the
snoop only for CORB/RIRB and enable the snoop for the stream buffers.
The resultant patch became a bit ugly, unfortunately, but we still can
live with it.
Reported-and-tested-by: Geoffrey McRae <geoff@spacevs.com>
Cc: <stable@vger.kernel.org> # 3.17+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the HD Audio Device IDs for the Intel Sunrise Point PCH.
[the item position rearranged by tiwai]
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS Phoebus with CMI8888 HD-audio chip (PCI id 13f6:5011) doesn't
work with HD-audio driver as is because of some weird nature. For
making DMA properly working, we need to disable MSI. The position
report buffer doesn't work, thus we need to force reading LPIB
instead. And yet, the codec CORB/RIRB communication gives errors
unless we disable the snooping (caching).
In this patch, all these workarounds are added as a quirk for the
device. The HD-audio *codec* chip needs yet another workaround, but
it'll be provided in the succeeding patch.
Reported-and-tested-by: Vincent Lejeune <vljn@ovi.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add HD Audio Device PCI ID for the Intel Braswell platform.
It is an HDA Intel PCH controller.
AZX_DCAPS_ALIGN_BUFSIZE is not necessary for this controller.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tony W Wang-oc