The driver doesn't support RX timestamping for non-PTP packets, but it
declares that it does. Restrict the reported RX filters to PTP v2 over
L2 and over L4.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IEEE 1588 support was declared too soon for the Ocelot switch. Out of
reset, this switch does not apply any special treatment for PTP packets,
i.e. when an event message is received, the natural tendency is to
forward it by MAC DA/VLAN ID. This poses a problem when the ingress port
is under a bridge, since user space application stacks (written
primarily for endpoint ports, not switches) like ptp4l expect that PTP
messages are always received on AF_PACKET / AF_INET sockets (depending
on the PTP transport being used), and never being autonomously
forwarded. Any forwarding, if necessary (for example in Transparent
Clock mode) is handled in software by ptp4l. Having the hardware forward
these packets too will cause duplicates which will confuse endpoints
connected to these switches.
So PTP over L2 barely works, in the sense that PTP packets reach the CPU
port, but they reach it via flooding, and therefore reach lots of other
unwanted destinations too. But PTP over IPv4/IPv6 does not work at all.
This is because the Ocelot switch have a separate destination port mask
for unknown IP multicast (which PTP over IP is) flooding compared to
unknown non-IP multicast (which PTP over L2 is) flooding. Specifically,
the driver allows the CPU port to be in the PGID_MC port group, but not
in PGID_MCIPV4 and PGID_MCIPV6. There are several presentations from
Allan Nielsen which explain that the embedded MIPS CPU on Ocelot
switches is not very powerful at all, so every penny they could save by
not allowing flooding to the CPU port module matters. Unknown IP
multicast did not make it.
The de facto consensus is that when a switch is PTP-aware and an
application stack for PTP is running, switches should have some sort of
trapping mechanism for PTP packets, to extract them from the hardware
data path. This avoids both problems:
(a) PTP packets are no longer flooded to unwanted destinations
(b) PTP over IP packets are no longer denied from reaching the CPU since
they arrive there via a trap and not via flooding
It is not the first time when this change is attempted. Last time, the
feedback from Allan Nielsen and Andrew Lunn was that the traps should
not be installed by default, and that PTP-unaware switching may be
desired for some use cases:
https://patchwork.ozlabs.org/project/netdev/patch/20190813025214.18601-5-yangbo.lu@nxp.com/
To address that feedback, the present patch adds the necessary packet
traps according to the RX filter configuration transmitted by user space
through the SIOCSHWTSTAMP ioctl. Trapping is done via VCAP IS2, where we
keep 5 filters, which are amended each time RX timestamping is enabled
or disabled on a port:
- 1 for PTP over L2
- 2 for PTP over IPv4 (UDP ports 319 and 320)
- 2 for PTP over IPv6 (UDP ports 319 and 320)
The cookie by which these filters (invisible to tc) are identified is
strategically chosen such that it does not collide with the filters used
for the ocelot-8021q tagging protocol by the Felix driver, or with the
MRP traps set up by the Ocelot library.
Other alternatives were considered, like patching user space to do
something, but there are so many ways in which PTP packets could be made
to reach the CPU, generically speaking, that "do what?" is a very valid
question. The ptp4l program from the linuxptp stack already attempts to
do something: it calls setsockopt(IP_ADD_MEMBERSHIP) (and
PACKET_ADD_MEMBERSHIP, respectively) which translates in both cases into
a dev_mc_add() on the interface, in the kernel:
https://github.com/richardcochran/linuxptp/blob/v3.1.1/udp.c#L73https://github.com/richardcochran/linuxptp/blob/v3.1.1/raw.c
Reality shows that this is not sufficient in case the interface belongs
to a switchdev driver, as dev_mc_add() does not show the intention to
trap a packet to the CPU, but rather the intention to not drop it (it is
strictly for RX filtering, same as promiscuous does not mean to send all
traffic to the CPU, but to not drop traffic with unknown MAC DA). This
topic is a can of worms in itself, and it would be great if user space
could just stay out of it.
On the other hand, setting up PTP traps privately within the driver is
not new by any stretch of the imagination:
https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c#L833https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/dsa/hirschmann/hellcreek.c#L1050https://elixir.bootlin.com/linux/v5.16-rc2/source/include/linux/dsa/sja1105.h#L21
So this is the approach taken here as well. The difference here being
that we prepare and destroy the traps per port, dynamically at runtime,
as opposed to driver init time, because apparently, PTP-unaware
forwarding is a use case.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Reported-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As opposed to event messages (Sync, PdelayReq etc) which require
timestamping, general messages (Announce, FollowUp etc) do not.
In PTP they are part of different streams of data.
IEEE 1588-2008 Annex D.2 "UDP port numbers" states that the UDP
destination port assigned by IANA is 319 for event messages, and 320 for
general messages. Yet the kernel seems to be missing the definition for
general messages. This patch adds it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VCAP (Versatile Content Aware Processor) is the TCAM-based engine behind
tc flower offload on ocelot, among other things. The ingress port mask
on which VCAP rules match is present as a bit field in the actual key of
the rule. This means that it is possible for a rule to be shared among
multiple source ports. When the rule is added one by one on each desired
port, that the ingress port mask of the key must be edited and rewritten
to hardware.
But the API in ocelot_vcap.c does not allow for this. For one thing,
ocelot_vcap_filter_add() and ocelot_vcap_filter_del() are not symmetric,
because ocelot_vcap_filter_add() works with a preallocated and
prepopulated filter and programs it to hardware, and
ocelot_vcap_filter_del() does both the job of removing the specified
filter from hardware, as well as kfreeing it. That is to say, the only
option of editing a filter in place, which is to delete it, modify the
structure and add it back, does not work because it results in
use-after-free.
This patch introduces ocelot_vcap_filter_replace, which trivially
reprograms a VCAP entry to hardware, at the exact same index at which it
existed before, without modifying any list or allocating any memory.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ocelot driver, when asked to timestamp all receiving packets, 1588
v1 or NTP, says "nah, here's 1588 v2 for you".
According to this discussion:
https://patchwork.kernel.org/project/netdevbpf/patch/20211104133204.19757-8-martin.kaistra@linutronix.de/#24577647
drivers that downgrade from a wider request to a narrower response (or
even a response where the intersection with the request is empty) are
buggy, and should return -ERANGE instead. This patch fixes that.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, HNS3 driver doesn't clear the reset flags of components after
successfully executing reset, it causes userspace info of
"Components reset" and "Components not reset" is incorrect.
So fix this problem by clear corresponding reset flag after reset process.
Fixes: ddccc5e368 ("net: hns3: add support for triggering reset by ethtool")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when user queries page pool info by debugfs command
"cat page_pool_info", the cnt of allocated page for page pool may be
incorrect because of memory inconsistency problem caused by compiler
optimization.
So this patch uses READ_ONCE() to read value of pages_state_hold_cnt to
fix this problem.
Fixes: 850bfb912a ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When page pool is not enabled, its address value is still NULL and page
pool should not be accessed, so add a check for it.
Fixes: 850bfb912a ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When PF is set to multi-TCs and configured mapping relationship between
priorities and TCs, the hardware will active these settings for this PF
and its VFs.
In this case when VF just uses one TC and its rx packets contain priority,
and if the priority is not mapped to TC0, as other TCs of VF is not valid,
hardware always put this kind of packets to the queue 0. It cause this kind
of packets of VF can not be used RSS function.
To fix this problem, set tc mode of all unused TCs of VF to the setting of
TC0, then rx packet with priority which map to unused TC will be direct to
TC0.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When pid filtering is activated in an instance, all of the events trace
files for that instance has the PID_FILTER flag set. This determines
whether or not pid filtering needs to be done on the event, otherwise the
event is executed as normal.
If pid filtering is enabled when an event is created (via a dynamic event
or modules), its flag is not updated to reflect the current state, and the
events are not filtered properly.
Cc: stable@vger.kernel.org
Fixes: 3fdaf80f4a ("tracing: Implement event pid filtering")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
If the variable 'p_bit->flags' is always 0,
the loop condition is always 0.
The variable 'j' may be greater than or equal to 32.
At this time, the array 'p_aeu->bits[32]' may be out
of bound.
Signed-off-by: zhangyue <zhangyue1@kylinos.cn>
Link: https://lore.kernel.org/r/20211125113610.273841-1-zhangyue1@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/pKc
-----END PGP SIGNATURE-----
Merge tag 'for-5.16-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"One more fix to the lzo code, a missing put_page causing memory leaks
when some error branches are taken"
* tag 'for-5.16-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix the memory leak caused in lzo_compress_pages()
When applications call shutdown() with SHUT_RDWR in userspace,
smc_close_active() calls kernel_sock_shutdown(), and it is called
twice in smc_shutdown().
This fixes this by checking sk_state before do clcsock shutdown, and
avoids missing the application's call of smc_shutdown().
Link: https://lore.kernel.org/linux-s390/1f67548e-cbf6-0dce-82b5-10288a4583bd@linux.ibm.com/
Fixes: 606a63c978 ("net/smc: Ensure the active closing peer first closes clcsock")
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20211126024134.45693-1-tonylu@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Inject error before dev_hold(real_dev) in register_vlan_dev(),
and execute the following testcase:
ip link add dev dummy1 type dummy
ip link add name dummy1.100 link dummy1 type vlan id 100
ip link del dev dummy1
When the dummy netdevice is removed, we will get a WARNING as following:
=======================================================================
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 2 PID: 0 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0
and an endless loop of:
=======================================================================
unregister_netdevice: waiting for dummy1 to become free. Usage count = -1073741824
That is because dev_put(real_dev) in vlan_dev_free() be called without
dev_hold(real_dev) in register_vlan_dev(). It makes the refcnt of real_dev
underflow.
Move the dev_hold(real_dev) to vlan_dev_init() which is the call-back of
ndo_init(). That makes dev_hold() and dev_put() for vlan's real_dev
symmetrical.
Fixes: 563bcbae3b ("net: vlan: fix a UAF in vlan_dev_real_dev()")
Reported-by: Petr Machata <petrm@nvidia.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/r/20211126015942.2918542-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All the filter names are missing _PTP in them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20211126031921.2466944-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ethtool_set_coalesce() now uses both the .get_coalesce() and
.set_coalesce() callbacks. But the check for their availability is
buggy, so changing the coalesce settings on a device where the driver
provides only _one_ of the callbacks results in a NULL pointer
dereference instead of an -EOPNOTSUPP.
Fix the condition so that the availability of both callbacks is
ensured. This also matches the netlink code.
Note that reproducing this requires some effort - it only affects the
legacy ioctl path, and needs a specific combination of driver options:
- have .get_coalesce() and .coalesce_supported but no
.set_coalesce(), or
- have .set_coalesce() but no .get_coalesce(). Here eg. ethtool doesn't
cause the crash as it first attempts to call ethtool_get_coalesce()
and bails out on error.
Fixes: f3ccfda193 ("ethtool: extend coalesce setting uAPI with CQE mode")
Cc: Yufeng Mo <moyufeng@huawei.com>
Cc: Huazhong Tan <tanhuazhong@huawei.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Link: https://lore.kernel.org/r/20211126175543.28000-1-jwi@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Device permissions is S_IALLUGO, with many unnecessary bits. Remove them
and also remove read and write permissions from group and others.
Before the change:
crwsrwsrwt 1 0 0 10, 125 Nov 25 13:59 /dev/virtual_nci
After the change:
crw------- 1 0 0 10, 125 Nov 25 14:05 /dev/virtual_nci
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Link: https://lore.kernel.org/r/20211125141457.716921-1-cascardo@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge fix and cleanup related to the management of ACPI device
properties for 5.16-rc3.
* acpi-properties:
ACPI: Make acpi_node_get_parent() local
ACPI: Get acpi_device's parent from the parent field
The Tx queues were not disabled in situations where the driver needed to
stop the interface to apply a new configuration. This could result in a
kernel panic when doing any of the 3 following actions:
* reconfiguring the number of queues (ethtool -L)
* reconfiguring the size of the ring buffers (ethtool -G)
* installing/removing an XDP program (ip l set dev ethX xdp)
Prevent the panic by making sure netif_tx_disable is called when stopping
an interface.
Without this patch, the following kernel panic can be observed when doing
any of the actions above:
Unable to handle kernel paging request at virtual address ffff80001238d040
[....]
Call trace:
dwmac4_set_addr+0x8/0x10
dev_hard_start_xmit+0xe4/0x1ac
sch_direct_xmit+0xe8/0x39c
__dev_queue_xmit+0x3ec/0xaf0
dev_queue_xmit+0x14/0x20
[...]
[ end trace 0000000000000002 ]---
Fixes: 5fabb01207 ("net: stmmac: Add initial XDP support")
Fixes: aa042f60e4 ("net: stmmac: Add support to Ethtool get/set ring parameters")
Fixes: 0366f7e06a ("net: stmmac: add ethtool support for get/set channels")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20211124154731.1676949-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here is a single binder driver fix for 5.16-rc3.
It resolves a problem reported in the set of binder fixes that went into
5.16-rc1. It has been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYaD22Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym0xQCdH/1o+RpPMrqVCU4S01N27wD083kAn1G5So0g
miNVDAAbiP9sljyDtVqj
=d38J
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fix from Greg KH:
"Here is a single binder driver fix for 5.16-rc3.
It resolves a problem reported in the set of binder fixes that went
into 5.16-rc1. It has been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
binder: fix test regression due to sender_euid change
Here are some small staging driver fixes and one driver removal for
5.16-rc3.
The fixes resolve a number of small issues found in 5.16-rc1, nothing
huge at all. The driver removal was due to a platform being removed in
5.16-rc1, but this driver was forgotten about. It wasn't being built
anymore so it's safe to delete.
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYaD5Bg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym6LgCdGUhkJrDZ4ddeOowUXJ8mjelUaZYAnR6Q7TQ3
/qXcTc/YRV1izMvnHmR9
=Nlfs
-----END PGP SIGNATURE-----
Merge tag 'staging-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some small staging driver fixes and one driver removal for
5.16-rc3.
The fixes resolve a number of small issues found in 5.16-rc1, nothing
huge at all. The driver removal was due to a platform being removed in
5.16-rc1, but this driver was forgotten about. It wasn't being built
anymore so it's safe to delete.
All have been in linux-next for a while with no reported problems"
* tag 'staging-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8192e: Fix use after free in _rtl92e_pci_disconnect()
staging: greybus: Add missing rwsem around snd_ctl_remove() calls
staging: Remove Netlogic XLP network driver
staging: r8188eu: fix a memory leak in rtw_wx_read32()
staging: r8188eu: use GFP_ATOMIC under spinlock
staging: r8188eu: Use kzalloc() with GFP_ATOMIC in atomic context
staging/fbtft: Fix backlight
staging: r8188eu: Fix breakage introduced when 5G code was removed
Here are a number of small USB fixes for reported problems for 5.16-rc3
Then include:
- typec driver fixes
- new usb-serial driver ids
- usb hub enumeration issues that were much reported
- gadget driver fixes
- dwc3 driver fix
- chipidea driver fixe
All of these have been in linux-next with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYaD5qA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykERACgkxi+H6dGSS7jVcoN+094/EnvZ7EAoInuQRY6
8iyGS1rDI9yKKNipPmI4
=oy2C
-----END PGP SIGNATURE-----
Merge tag 'usb-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for reported problems for
5.16-rc3
They include:
- typec driver fixes
- new usb-serial driver ids
- usb hub enumeration issues that were much reported
- gadget driver fixes
- dwc3 driver fix
- chipidea driver fixe
All of these have been in linux-next with no reported problems"
* tag 'usb-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: option: add Fibocom FM101-GL variants
usb: typec: tipd: Fix initialization sequence for cd321x
usb: typec: tipd: Fix typo in cd321x_switch_power_state
usb: hub: Fix locking issues with address0_mutex
USB: serial: pl2303: fix GC type detection
USB: serial: option: add Telit LE910S1 0x9200 composition
usb: chipidea: ci_hdrc_imx: fix potential error pointer dereference in probe
usb: hub: Fix usb enumeration issue due to address0 race
usb: typec: fusb302: Fix masking of comparator and bc_lvl interrupts
usb: dwc3: leave default DMA for PCI devices
usb: dwc2: hcd_queue: Fix use of floating point literal
usb: dwc3: gadget: Fix null pointer exception
usb: gadget: udc-xilinx: Fix an error handling path in 'xudc_probe()'
usb: xhci: tegra: Check padctrl interrupt presence in device tree
usb: dwc2: gadget: Fix ISOC flow for elapsed frames
usb: dwc3: gadget: Check for L1/L2/U3 for Start Transfer
usb: dwc3: gadget: Ignore NoStream after End Transfer
usb: dwc3: core: Revise GHWPARAMS9 offset
Pull i2c fixes from Wolfram Sang:
"I2C has an interrupt storm fix for the i801, better timeout handling
for the new virtio driver, and some documentation fixes this time"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
docs: i2c: smbus-protocol: mention the repeated start condition
i2c: virtio: disable timeout handling
i2c: i801: Fix interrupt storm from SMB_ALERT signal
i2c: i801: Restore INTREN on unload
dt-bindings: i2c: imx-lpi2c: Fix i.MX 8QM compatible matching
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYaD8mwAKCRCAXGG7T9hj
vspAAPwLA5SUorji33PTetwmcpLcoRJ3Q4HAPz+bOPdm9iL/PgD/V8MtxFrFebBs
AJoa+GmBarUNn7XCqKnCcA64iXhrpQw=
=6GY3
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.16c-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- Kconfig fix to make it possible to control building of the privcmd
driver
- three fixes for issues identified by the kernel test robot
- a five-patch series to simplify timeout handling for Xen PV driver
initialization
- two patches to fix error paths in xenstore/xenbus driver
initialization
* tag 'for-linus-5.16c-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: make HYPERVISOR_set_debugreg() always_inline
xen: make HYPERVISOR_get_debugreg() always_inline
xen: detect uninitialized xenbus in xenbus_init
xen: flag xen_snd_front to be not essential for system boot
xen: flag pvcalls-front to be not essential for system boot
xen: flag hvc_xen to be not essential for system boot
xen: flag xen_drm_front to be not essential for system boot
xen: add "not_essential" flag to struct xenbus_driver
xen/pvh: add missing prototype to header
xen: don't continue xenstore initialization in case of errors
xen/privcmd: make option visible in Kconfig
- Evaluate uaccess macro arguments outside of the critical section
- Tighten up VM_BUG_ON() in pmd_populate_kernel() to avoid false positive
- Fix ftrace stack unwinding using HAVE_FUNCTION_GRAPH_RET_ADDR_PTR
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAmGgqs4QHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNBKAB/4r/+K4xjuP4x1CX7Tv3VRkwLvkEiHYdm64
Ljsf0e//AnezlWRJsR+MOKlp81bLcJu7Y3U+jkDYCjbJEWWwANC6/3dGmtmW4XPc
hgQtb+ngS/HjyVD83epSgtAo85L6xfOgExThYTWmiQGpwsyBnMAD21MQmPtllHjX
xvifkIYzLIUdw4orQv+RyY262kI26y2ugj4BdZ4KSzUiCJWv3T+Tywmf8q8S6a5W
s491oB/63bR24bytL3sni7ltDdg42/24arCoYOJQ8WCbvFDY9seCH0OX8jhbZzR/
pcn61SsaPF58MKcccQjjRnWv1rvy9sXGci1QoxWjmuC2CviJxovZ
=uDnd
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Three arm64 fixes.
The main one is a fix to the way in which we evaluate the macro
arguments to our uaccess routines, which we _think_ might be the root
cause behind some unkillable tasks we've seen in the Android arm64 CI
farm (testing is ongoing). In any case, it's worth fixing.
Other than that, we've toned down an over-zealous VM_BUG_ON() and
fixed ftrace stack unwinding in a bunch of cases.
Summary:
- Evaluate uaccess macro arguments outside of the critical section
- Tighten up VM_BUG_ON() in pmd_populate_kernel() to avoid false positive
- Fix ftrace stack unwinding using HAVE_FUNCTION_GRAPH_RET_ADDR_PTR"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: uaccess: avoid blocking within critical sections
arm64: mm: Fix VM_BUG_ON(mm != &init_mm) for trans_pgd
arm64: ftrace: use HAVE_FUNCTION_GRAPH_RET_ADDR_PTR
When CONFIG_COMMON_CLOCK is disabled, the 8996 specific
phy code is left out, which results in a link failure:
ld: drivers/gpu/drm/msm/hdmi/hdmi_phy.o:(.rodata+0x3f0): undefined reference to `msm_hdmi_phy_8996_cfg'
This was only exposed after it became possible to build
test the driver without the clock interfaces.
Make COMMON_CLK a hard dependency for compile testing,
and simplify it a little based on that.
Fixes: b3ed524f84 ("drm/msm: allow compile_test on !ARM")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211013144308.2248978-1-arnd@kernel.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
If writeback isn't configured, then we get the following warning when
compiling zram:
drivers/block/zram/zram_drv.c:1824:45: warning: unused variable 'zram_wb_devops' [-Wunused-const-variable]
Make sure we only define the block_device_operations if that option is
enabled.
Link: https://lore.kernel.org/lkml/202111261614.gCJMqcyh-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We need to call rq_qos_done() regardless of whether or not we're freeing
the request or not, as the reference count doesn't cover the IO completion
tracking.
Fixes: f794f3351f ("block: add support for blk_mq_end_request_batch()")
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reported-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
WARNING: inconsistent lock state
5.16.0-rc2-syzkaller #0 Not tainted
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
ffff888078e11418 (&ctx->timeout_lock
){?.+.}-{2:2}
, at: io_timeout_fn+0x6f/0x360 fs/io_uring.c:5943
{HARDIRQ-ON-W} state was registered at:
[...]
spin_unlock_irq include/linux/spinlock.h:399 [inline]
__io_poll_remove_one fs/io_uring.c:5669 [inline]
__io_poll_remove_one fs/io_uring.c:5654 [inline]
io_poll_remove_one+0x236/0x870 fs/io_uring.c:5680
io_poll_remove_all+0x1af/0x235 fs/io_uring.c:5709
io_ring_ctx_wait_and_kill+0x1cc/0x322 fs/io_uring.c:9534
io_uring_release+0x42/0x46 fs/io_uring.c:9554
__fput+0x286/0x9f0 fs/file_table.c:280
task_work_run+0xdd/0x1a0 kernel/task_work.c:164
exit_task_work include/linux/task_work.h:32 [inline]
do_exit+0xc14/0x2b40 kernel/exit.c:832
674ee8e1b4 ("io_uring: correct link-list traversal locking") fixed a
data race but introduced a possible deadlock and inconsistentcy in irq
states. E.g.
io_poll_remove_all()
spin_lock_irq(timeout_lock)
io_poll_remove_one()
spin_lock/unlock_irq(poll_lock);
spin_unlock_irq(timeout_lock)
Another type of problem is freeing a request while holding
->timeout_lock, which may leads to a deadlock in
io_commit_cqring() -> io_flush_timeouts() and other places.
Having 3 nested locks is also too ugly. Add io_match_task_safe(), which
would briefly take and release timeout_lock for race prevention inside,
so the actuall request cancellation / free / etc. code doesn't have it
taken.
Reported-by: syzbot+ff49a3059d49b0ca0eec@syzkaller.appspotmail.com
Reported-by: syzbot+847f02ec20a6609a328b@syzkaller.appspotmail.com
Reported-by: syzbot+3368aadcd30425ceb53b@syzkaller.appspotmail.com
Reported-by: syzbot+51ce8887cdef77c9ac83@syzkaller.appspotmail.com
Reported-by: syzbot+3cb756a49d2f394a9ee3@syzkaller.appspotmail.com
Fixes: 674ee8e1b4 ("io_uring: correct link-list traversal locking")
Cc: stable@kernel.org # 5.15+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/397f7ebf3f4171f1abe41f708ac1ecb5766f0b68.1637937097.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
WARNING: CPU: 1 PID: 20 at fs/io_uring.c:6269 io_try_cancel_userdata+0x3c5/0x640 fs/io_uring.c:6269
CPU: 1 PID: 20 Comm: kworker/1:0 Not tainted 5.16.0-rc1-syzkaller #0
Workqueue: events io_fallback_req_func
RIP: 0010:io_try_cancel_userdata+0x3c5/0x640 fs/io_uring.c:6269
Call Trace:
<TASK>
io_req_task_link_timeout+0x6b/0x1e0 fs/io_uring.c:6886
io_fallback_req_func+0xf9/0x1ae fs/io_uring.c:1334
process_one_work+0x9b2/0x1690 kernel/workqueue.c:2298
worker_thread+0x658/0x11f0 kernel/workqueue.c:2445
kthread+0x405/0x4f0 kernel/kthread.c:327
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
</TASK>
We need original task's context to do cancellations, so if it's dying
and the callback is executed in a fallback mode, fail the cancellation
attempt.
Fixes: 89b263f6d5 ("io_uring: run linked timeouts from task_work")
Cc: stable@kernel.org # 5.15+
Reported-by: syzbot+ab0cfe96c2b3cd1c1153@syzkaller.appspotmail.com
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/4c41c5f379c6941ad5a07cd48cb66ed62199cf7e.1637937097.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
[BUG]
Fstests generic/027 is pretty easy to trigger a slow but steady memory
leak if run with "-o compress=lzo" mount option.
Normally one single run of generic/027 is enough to eat up at least 4G ram.
[CAUSE]
In commit d4088803f5 ("btrfs: subpage: make lzo_compress_pages()
compatible") we changed how @page_in is released.
But that refactoring makes @page_in only released after all pages being
compressed.
This leaves error path not releasing @page_in. And by "error path"
things like incompressible data will also be treated as an error
(-E2BIG).
Thus it can cause a memory leak if even nothing wrong happened.
[FIX]
Add check under @out label to release @page_in when needed, so when we
hit any error, the input page is properly released.
Reported-by: Josef Bacik <josef@toxicpanda.com>
Fixes: d4088803f5 ("btrfs: subpage: make lzo_compress_pages() compatible")
Reviewed-and-tested-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
INVLPG operates on guest virtual address, which are represented by
vcpu->arch.walk_mmu. In nested virtualization scenarios,
kvm_mmu_invlpg() was using the wrong MMU structure; if L2's invlpg were
emulated by L0 (in practice, it hardly happen) when nested two-dimensional
paging is enabled, the call to ->tlb_flush_gva() would be skipped and
the hardware TLB entry would not be invalidated.
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20211124122055.64424-5-jiangshanlai@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the is an L1 with nNPT in 32bit, the shadow walk starts with
pae_root.
Fixes: a717a780fc ("KVM: x86/mmu: Support shadowing NPT when 5-level paging is enabled in host)
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20211124122055.64424-2-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With the elevated 'KVM_CAP_MAX_VCPUS' value kvm_create_max_vcpus test
may hit RLIMIT_NOFILE limits:
# ./kvm_create_max_vcpus
KVM_CAP_MAX_VCPU_ID: 4096
KVM_CAP_MAX_VCPUS: 1024
Testing creating 1024 vCPUs, with IDs 0...1023.
/dev/kvm not available (errno: 24), skipping test
Adjust RLIMIT_NOFILE limits to make sure KVM_CAP_MAX_VCPUS fds can be
opened. Note, raising hard limit ('rlim_max') requires CAP_SYS_RESOURCE
capability which is generally not needed to run kvm selftests (but without
raising the limit the test is doomed to fail anyway).
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211123135953.667434-1-vkuznets@redhat.com>
[Skip the test if the hard limit can be raised. - Paolo]
Reviewed-by: Sean Christopherson <seanjc@google.com>
Tested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 63f5a1909f ("KVM: x86: Alert userspace that KVM_SET_CPUID{,2}
after KVM_RUN is broken") officially deprecated KVM_SET_CPUID{,2} ioctls
after first successful KVM_RUN and promissed to make this sequence forbiden
in 5.16. It's time to fulfil the promise.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211122175818.608220-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
hyperv_features's sole purpose is to test access to various Hyper-V MSRs
and hypercalls with different CPUID data. As KVM_SET_CPUID2 after KVM_RUN
is deprecated and soon-to-be forbidden, avoid it by re-creating test VM
for each sub-test.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211122175818.608220-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fully emulate a guest TLB flush on nested VM-Enter which changes vpid12,
i.e. L2's VPID, instead of simply doing INVVPID to flush real hardware's
TLB entries for vpid02. From L1's perspective, changing L2's VPID is
effectively a TLB flush unless "hardware" has previously cached entries
for the new vpid12. Because KVM tracks only a single vpid12, KVM doesn't
know if the new vpid12 has been used in the past and so must treat it as
a brand new, never been used VPID, i.e. must assume that the new vpid12
represents a TLB flush from L1's perspective.
For example, if L1 and L2 share a CR3, the first VM-Enter to L2 (with a
VPID) is effectively a TLB flush as hardware/KVM has never seen vpid12
and thus can't have cached entries in the TLB for vpid12.
Reported-by: Lai Jiangshan <jiangshanlai+lkml@gmail.com>
Fixes: 5c614b3583 ("KVM: nVMX: nested VPID emulation")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211125014944.536398-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Like KVM_REQ_TLB_FLUSH_CURRENT, the GUEST variant needs to be serviced at
nested transitions, as KVM doesn't track requests for L1 vs L2. E.g. if
there's a pending flush when a nested VM-Exit occurs, then the flush was
requested in the context of L2 and needs to be handled before switching
to L1, otherwise the flush for L2 would effectiely be lost.
Opportunistically add a helper to handle CURRENT and GUEST as a pair, the
logic for when they need to be serviced is identical as both requests are
tied to L1 vs. L2, the only difference is the scope of the flush.
Reported-by: Lai Jiangshan <jiangshanlai+lkml@gmail.com>
Fixes: 07ffaf343e ("KVM: nVMX: Sync all PGDs on nested transition with shadow paging")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211125014944.536398-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Flush the current VPID when handling KVM_REQ_TLB_FLUSH_GUEST instead of
always flushing vpid01. Any TLB flush that is triggered when L2 is
active is scoped to L2's VPID (if it has one), e.g. if L2 toggles CR4.PGE
and L1 doesn't intercept PGE writes, then KVM's emulation of the TLB
flush needs to be applied to L2's VPID.
Reported-by: Lai Jiangshan <jiangshanlai+lkml@gmail.com>
Fixes: 07ffaf343e ("KVM: nVMX: Sync all PGDs on nested transition with shadow paging")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211125014944.536398-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The capability, albeit present, was never exposed via KVM_CHECK_EXTENSION.
Fixes: b56639318b ("KVM: SEV: Add support for SEV intra host migration")
Cc: Peter Gonda <pgonda@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Ensure that the ASID are freed promptly, which becomes more important
when more tests are added to this file.
Cc: Peter Gonda <pgonda@google.com>
Cc: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM_CAP_VM_MOVE_ENC_CONTEXT_FROM leaves the source VM in a dead state,
so migrating back to the original source VM fails the ioctl. Adjust
the test.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Synchronize the two calls to kvm_x86_sync_pir_to_irr. The one
in the reenter-guest fast path invoked the callback unconditionally
even if LAPIC is present but disabled. In this case, there are
no interrupts to deliver, and therefore posted interrupts can
be ignored.
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is not an unrecoverable situation. Users of kvm_read_guest_offset_cached
and kvm_write_guest_offset_cached must expect the read/write to fail, and
therefore it is possible to just return early with an error value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
An uninitialized gfn_to_hva_cache has ghc->len == 0, which causes
the accessors to croak very loudly. While a BUG_ON is definitely
_too_ loud and a bug on its own, there is indeed an issue of using
the caches in such a way that they could not have been initialized,
because ghc->gpa == 0 might match and thus kvm_gfn_to_hva_cache_init
would not be called.
For the vmcs12_cache, the solution is simply to invoke
kvm_gfn_to_hva_cache_init unconditionally: we already know
that the cache does not match the current VMCS pointer.
For the shadow_vmcs12_cache, there is no similar condition
that checks the VMCS link pointer, so invalidate the cache
on VMXON.
Fixes: cee66664dc ("KVM: nVMX: Use a gfn_to_hva_cache for vmptrld")
Acked-by: David Woodhouse <dwmw@amazon.co.uk>
Reported-by: syzbot+7b7db8bb4db6fd5e157b@syzkaller.appspotmail.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
