Because of the logic in place, SW_HUGE_PACKET can never be set.
(If the first condition is true, then the 2nd one is also true, but is not
executed)
Change the logic and update each bit individually.
Fixes: 29d1e85f45 ("net: dsa: microchip: ksz8: add MTU configuration support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/43107d9e8b5b8b05f0cbd4e1f47a2bb88c8747b2.1681755535.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The force watchdog event bit is not cleared during SW reset in the
mv88e6393x switch. This is a different behavior compared to mv886390 which
clears the force WD event bit as advertised. This causes a force WD event
to be handled over and over again as the SW reset following the event never
clears the force WD event bit.
Explicitly clear the watchdog event register to 0 in irq_action when
handling an event to prevent the switch from sending continuous interrupts.
Marvell aren't aware of any other stuck bits apart from the force WD
bit.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family"
Signed-off-by: Gustav Ekelund <gustaek@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not set the MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP bit on CPU or DSA ports.
This allows the host CPU port to be a regular IGMP listener by sending out
IGMP Membership Reports, which would otherwise not be forwarded by the
mv88exxx chip, but directly looped back to the CPU port itself.
Fixes: 54d792f257 ("net: dsa: Centralise global and port setup code into mv88e6xxx.")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230329150140.701559-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement phy_read16() and phy_write16() ops for B53 MMAP to avoid accessing
B53_PORT_MII_PAGE registers which hangs the device.
This access should be done through the MDIO Mux bus controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FID is directly mapped to VID. However, configuring a MAC address with a
VID != 0 resulted in incorrect configuration due to an incorrect bit
mask. This kernel commit fixed the issue by correcting the bit mask and
ensuring proper configuration of MAC addresses with non-zero VID.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current regmap bulk access is broken, resulting to wrong reads/writes
if ksz_read64/ksz_write64 functions are used.
Mostly this issue was visible by using ksz8_fdb_dump(), which returned
corrupt MAC address.
The reason is that regmap was configured to have max_raw_read/write,
even if ksz8863_mdio_read/write functions are able to handle unlimited
read/write accesses. On ksz_read64 function we are using multiple 32bit
accesses by incrementing each access by 1 instead of 4. Resulting buffer
had 01234567.12345678 instead of 01234567.89abcdef.
We have multiple ways to fix it:
- enable 4 byte alignment for 32bit accesses. Since the HW do not have
this requirement. It will break driver.
- disable max_raw_* limit.
This patch is removing max_raw_* limit for regmap accesses in ksz8863_smi.
Fixes: 60a3647600 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the dynamic MAC table is empty, we will still extract one outdated
entry. Fix it by using correct bit offset.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are using wrong offset, so we will get not a timestamp.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current ksz8_fdb_dump() is able to extract only max 249 entries on
the ksz8863/ksz8873 series of switches. This happened due to wrong
bit mask and offset calculation.
This commit corrects the issue and allows for the complete extraction of
all 1024 entries.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch, the ksz8_fdb_dump() function had several issues, such
as uninitialized variables and incorrect usage of source port as a bit
mask. These problems caused inaccurate reporting of vid information and
port assignment in the bridge fdb.
Fixes: e587be759e ("net: dsa: microchip: update fdb add/del/dump in ksz_common")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The probe function sets priv->chip_data to (void *)priv + sizeof(*priv)
with the expectation that priv has enough trailing space.
However, only realtek-smi actually allocated this chip_data space.
Do likewise in realtek-mdio to fix out-of-bounds accesses.
These accesses likely went unnoticed so far, because of an (unused)
buf[4096] member in struct realtek_priv, which caused kmalloc to
round up the allocated buffer to a big enough size, so nothing of
value was overwritten. With a different allocator (like in the barebox
bootloader port of the driver) or with KASAN, the memory corruption
becomes quickly apparent.
Fixes: aac9400106 ("net: dsa: realtek: add new mdio interface for drivers")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20230323103735.2331786-1-a.fatoum@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move setting the ssc_delta variable to under the PHY_INTERFACE_MODE_TRGMII
case as it's only needed when trgmii is used.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230320190520.124513-3-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move lowering the TRGMII Tx clock driving to mt7530_setup(), after setting
the core clock, as seen on the U-Boot MediaTek ethernet driver.
Move the code which looks like it lowers the TRGMII Rx clock driving to
after the TRGMII Tx clock driving is lowered. This is run after lowering
the Tx clock driving on the U-Boot MediaTek ethernet driver as well.
This way, the switch should consume less power regardless of port 6 being
used.
Update the comment explaining mt7530_pad_clk_setup().
Tested rgmii and trgmii modes of port 6 and rgmii mode of port 5 on MCM
MT7530 on MT7621AT Unielec U7621-06 and standalone MT7530 on MT7623NI
Bananapi BPI-R2.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Link: 29a48bf9cc/drivers/net/mtk_eth.c (L682)
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230320190520.124513-2-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Split the code that enables and disables TRGMII clocks and core clock.
Move enabling and disabling core clock to mt7530_pll_setup() as it's
supposed to be run there.
Add 20 ms delay before enabling the core clock as seen on the U-Boot
MediaTek ethernet driver.
Change the comment for enabling and disabling TRGMII clocks as the code
seems to affect both TXC and RXC.
Tested rgmii and trgmii modes of port 6 and rgmii mode of port 5 on MCM
MT7530 on MT7621AT Unielec U7621-06 and standalone MT7530 on MT7623NI
Bananapi BPI-R2.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Link: 29a48bf9cc/drivers/net/mtk_eth.c (L589)
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230320190520.124513-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CPU port should also be enabled in order to get a working switch.
Fixes: a5538a777b ("net: dsa: b53: mmap: Add device tree support")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230316172807.460146-1-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit has replaced a ksz_write8() call to address
REG_PORT_5_CTRL_6 (0x56) with a ksz_set_xmii() -> ksz_pwrite8() call to
regs[P_XMII_CTRL_1], which is also defined as 0x56 for ksz8795_regs[].
The trouble is that, when compared to ksz_write8(), ksz_pwrite8() also
adjusts the register offset with the port base address. So in reality,
ksz_pwrite8(offset=0x56) accesses register 0x56 + 0x50 = 0xa6, which in
this switch appears to be unmapped, and the RGMII delay configuration on
the CPU port does nothing.
So if the switch wasn't fine with the RGMII delay configuration done
through pin strapping and relied on Linux to apply a different one in
order to pass traffic, this is now broken.
Using the offset translation logic imposed by ksz_pwrite8(), the correct
value for regs[P_XMII_CTRL_1] should have been 0x6 on ksz8795_regs[], in
order to really end up accessing register 0x56.
Static code analysis shows that, despite there being multiple other
accesses to regs[P_XMII_CTRL_1] in this driver, the only code path that
is applicable to ksz8795_regs[] and ksz8_dev_ops is ksz_set_xmii().
Therefore, the problem is isolated to RGMII delays.
In its current form, ksz8795_regs[] contains the same value for
P_XMII_CTRL_0 and for P_XMII_CTRL_1, and this raises valid suspicions
that writes made by the driver to regs[P_XMII_CTRL_0] might overwrite
writes made to regs[P_XMII_CTRL_1] or vice versa.
Again, static analysis shows that the only accesses to P_XMII_CTRL_0
from the driver are made from code paths which are not reachable with
ksz8_dev_ops. So the accesses made by ksz_set_xmii() are safe for this
switch family.
[ vladimiroltean: rewrote commit message ]
Fixes: c476bede4b ("net: dsa: microchip: ksz8795: use common xmii function")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230315231916.2998480-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are 3 classes of switch families that the driver is aware of, as
far as mv88e6xxx_change_mtu() is concerned:
- MTU configuration is available per port. Here, the
chip->info->ops->port_set_jumbo_size() method will be present.
- MTU configuration is global to the switch. Here, the
chip->info->ops->set_max_frame_size() method will be present.
- We don't know how to change the MTU. Here, none of the above methods
will be present.
Switch families MV88E6165, MV88E6191, MV88E6220, MV88E6250 and MV88E6290
fall in category 3.
The blamed commit has adjusted the MTU for all 3 categories by EDSA_HLEN
(8 bytes), resulting in a new maximum MTU of 1492 being reported by the
driver for these switches.
I don't have the hardware to test, but I do have a MV88E6390 switch on
which I can simulate this by commenting out its .port_set_jumbo_size
definition from mv88e6390_ops. The result is this set of messages at
probe time:
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 1
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 2
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 3
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 4
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 5
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 6
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 7
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 8
It is highly implausible that there exist Ethernet switches which don't
support the standard MTU of 1500 octets, and this is what the DSA
framework says as well - the error comes from dsa_slave_create() ->
dsa_slave_change_mtu(slave_dev, ETH_DATA_LEN).
But the error messages are alarming, and it would be good to suppress
them.
As a consequence of this unlikeliness, we reimplement mv88e6xxx_get_max_mtu()
and mv88e6xxx_change_mtu() on switches from the 3rd category as follows:
the maximum supported MTU is 1500, and any request to set the MTU to a
value larger than that fails in dev_validate_mtu().
Fixes: b9c587fed6 ("dsa: mv88e6xxx: Include tagger overhead when setting MTU for DSA and CPU ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As my testing on the MCM MT7530 switch on MT7621 SoC shows, setting the PLL
frequency does not affect MII modes other than trgmii on port 5 and port 6.
So the assumption is that the operation here called "setting the PLL
frequency" actually sets the frequency of the TRGMII TX clock.
Make it so that it and the rest of the trgmii setup run only when the
trgmii mode is used.
Tested rgmii and trgmii modes of port 6 on MCM MT7530 on MT7621AT Unielec
U7621-06 and standalone MT7530 on MT7623NI Bananapi BPI-R2.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230310073338.5836-2-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove now incorrect comment regarding port 5 as GMAC5. This is supposed to
be supported since commit 38f790a805 ("net: dsa: mt7530: Add support for
port 5") under mt7530_setup_port5().
Fixes: 38f790a805 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230310073338.5836-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MT7530 switch from the MT7621 SoC has 2 ports which can be set up as
internal: port 5 and 6. Arınç reports that the GMAC1 attached to port 5
receives corrupted frames, unless port 6 (attached to GMAC0) has been
brought up by the driver. This is true regardless of whether port 5 is
used as a user port or as a CPU port (carrying DSA tags).
Offline debugging (blind for me) which began in the linked thread showed
experimentally that the configuration done by the driver for port 6
contains a step which is needed by port 5 as well - the write to
CORE_GSWPLL_GRP2 (note that I've no idea as to what it does, apart from
the comment "Set core clock into 500Mhz"). Prints put by Arınç show that
the reset value of CORE_GSWPLL_GRP2 is RG_GSWPLL_POSDIV_500M(1) |
RG_GSWPLL_FBKDIV_500M(40) (0x128), both on the MCM MT7530 from the
MT7621 SoC, as well as on the standalone MT7530 from MT7623NI Bananapi
BPI-R2. Apparently, port 5 on the standalone MT7530 can work under both
values of the register, while on the MT7621 SoC it cannot.
The call path that triggers the register write is:
mt753x_phylink_mac_config() for port 6
-> mt753x_pad_setup()
-> mt7530_pad_clk_setup()
so this fully explains the behavior noticed by Arınç, that bringing port
6 up is necessary.
The simplest fix for the problem is to extract the register writes which
are needed for both port 5 and 6 into a common mt7530_pll_setup()
function, which is called at mt7530_setup() time, immediately after
switch reset. We can argue that this mirrors the code layout introduced
in mt7531_setup() by commit 42bc4fafe3 ("net: mt7531: only do PLL once
after the reset"), in that the PLL setup has the exact same positioning,
and further work to consolidate the separate setup() functions is not
hindered.
Testing confirms that:
- the slight reordering of writes to MT7530_P6ECR and to
CORE_GSWPLL_GRP1 / CORE_GSWPLL_GRP2 introduced by this change does not
appear to cause problems for the operation of port 6 on MT7621 and on
MT7623 (where port 5 also always worked)
- packets sent through port 5 are not corrupted anymore, regardless of
whether port 6 is enabled by phylink or not (or even present in the
device tree)
My algorithm for determining the Fixes: tag is as follows. Testing shows
that some logic from mt7530_pad_clk_setup() is needed even for port 5.
Prior to commit ca366d6c88 ("net: dsa: mt7530: Convert to PHYLINK
API"), a call did exist for all phy_is_pseudo_fixed_link() ports - so
port 5 included. That commit replaced it with a temporary "Port 5 is not
supported!" comment, and the following commit 38f790a805 ("net: dsa:
mt7530: Add support for port 5") replaced that comment with a
configuration procedure in mt7530_setup_port5() which was insufficient
for port 5 to work. I'm laying the blame on the patch that claimed
support for port 5, although one would have also needed the change from
commit c3b8e07909 ("net: dsa: mt7530: setup core clock even in TRGMII
mode") for the write to be performed completely independently from port
6's configuration.
Thanks go to Arınç for describing the problem, for debugging and for
testing.
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/netdev/f297c2c4-6e7c-57ac-2394-f6025d309b9d@arinc9.com/
Fixes: 38f790a805 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230307155411.868573-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During review of ocelot_ext, it created a private phylink instance
that wasn't necessary. This was removed for subsequent postings,
but the include file seems to have been left behind. Remove it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compiling a kernel which has both CONFIG_NET_DSA_MSCC_OCELOT_EXT
and CONFIG_MSCC_OCELOT_SWITCH enabled, the following error message will
be printed:
[ 5.266588] Error: Driver 'ocelot-switch' is already registered, aborting...
Rename the ocelot_ext.c driver to "ocelot-ext-switch" to avoid the name
duplication, and update the mfd_cell entry for its resources.
Fixes: 3d7316ac81 ("net: dsa: ocelot: add external ocelot switch control")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit did not properly convert the resource start/end format
into the DEFINE_RES_MEM_NAMED() start/length format, resulting in a
resource for vsc9959_imdio_res which is much longer than expected:
$ cat /proc/iomem
1f8000000-1f815ffff : pcie@1f0000000
1f8140000-1f815ffff : 0000:00:00.5
1f8148030-1f815006f : imdio
vs (correct)
$ cat /proc/iomem
1f8000000-1f815ffff : pcie@1f0000000
1f8140000-1f815ffff : 0000:00:00.5
1f8148030-1f814803f : imdio
Luckily it's not big enough to exceed the size of the parent resource
(pci_resource_end(pdev, VSC9959_IMDIO_PCI_BAR)), and it doesn't overlap
with anything else that the Linux driver uses currently, so the larger
than expected size isn't a practical problem that I can see. Although it
is clearly wrong in the /proc/iomem output.
Fixes: 044d447a80 ("net: dsa: felix: use DEFINE_RES_MEM_NAMED for resources")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the refactoring in the commit below, vsc9953_mdio_read() was
replaced with mscc_miim_read(), which has one extra step: it checks for
the MSCC_MIIM_DATA_ERROR bits before returning the result.
On T1040RDB, there are 8 QSGMII PCSes belonging to the switch, and they
are organized in 2 groups. First group responds to MDIO addresses 4-7
because QSGMIIACR1[MDEV_PORT] is 1, and the second group responds to
MDIO addresses 8-11 because QSGMIIBCR1[MDEV_PORT] is 2. I have double
checked that these values are correctly set in the SERDES, as well as
PCCR1[QSGMA_CFG] and PCCR1[QSGMB_CFG] are both 0b01.
mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 4 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 4 reg 0x5 MIIM_DATA 0x3da01, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR
As can be seen, the data in MIIM_DATA is still valid despite having the
MSCC_MIIM_DATA_ERROR bits set. The driver as introduced in commit
84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953
switch") was ignoring these bits, perhaps deliberately (although
unbeknownst to me).
This is an old IP and the hardware team cannot seem to be able to help
me track down a plausible reason for these failures. I'll keep
investigating, but in the meantime, this is a direct regression which
must be restored to a working state.
The only thing I can do is keep ignoring the errors as before.
Fixes: b996584523 ("net: dsa: ocelot: felix: utilize shared mscc-miim driver for indirect MDIO access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of KSZ9477 family switches provides EEE support. To enable it, we
just need to register set_mac_eee/set_mac_eee handlers and validate
supported chip version and port.
Currently supported chip variants are: KSZ8563, KSZ9477, KSZ9563,
KSZ9567, KSZ9893, KSZ9896, KSZ9897. KSZ8563 supports EEE only with
100BaseTX/Full. Other chips support 100BaseTX/Full and 1000BaseTX/Full.
Low Power Idle configuration is not supported and currently not
documented in the datasheets.
EEE PHY specific tunings are not documented in the switch datasheets, but can
overlap with KSZ9131 specification.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new user of MSCC_OCELOT_SWITCH_LIB was added, bringing back an old
link failure that was fixed with e5f3155267 ("ethernet: fix
PTP_1588_CLOCK dependencies"):
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_ptp_enable':
ocelot_ptp.c:(.text+0x8ee): undefined reference to `ptp_find_pin'
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_get_ts_info':
ocelot_ptp.c:(.text+0xd5d): undefined reference to `ptp_clock_index'
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_init_timestamp':
ocelot_ptp.c:(.text+0x15ca): undefined reference to `ptp_clock_register'
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_deinit_timestamp':
ocelot_ptp.c:(.text+0x16b7): undefined reference to `ptp_clock_unregister'
Add the same PTP dependency here, as well as in the MSCC_OCELOT_SWITCH_LIB
symbol itself to make it more obvious what is going on when the next
driver selects it.
Fixes: 3d7316ac81 ("net: dsa: ocelot: add external ocelot switch control")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20230209124435.1317781-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Frank reports that in a mt7530 setup where some ports are standalone and
some are in a VLAN-aware bridge, 8021q uppers of the standalone ports
lose their VLAN tag on xmit, as seen by the link partner.
This seems to occur because once the other ports join the VLAN-aware
bridge, mt7530_port_vlan_filtering() also calls
mt7530_port_set_vlan_aware(ds, cpu_dp->index), and this affects the way
that the switch processes the traffic of the standalone port.
Relevant is the PVC_EG_TAG bit. The MT7530 documentation says about it:
EG_TAG: Incoming Port Egress Tag VLAN Attribution
0: disabled (system default)
1: consistent (keep the original ingress tag attribute)
My interpretation is that this setting applies on the ingress port, and
"disabled" is basically the normal behavior, where the egress tag format
of the packet (tagged or untagged) is decided by the VLAN table
(MT7530_VLAN_EGRESS_UNTAG or MT7530_VLAN_EGRESS_TAG).
But there is also an option of overriding the system default behavior,
and for the egress tagging format of packets to be decided not by the
VLAN table, but simply by copying the ingress tag format (if ingress was
tagged, egress is tagged; if ingress was untagged, egress is untagged;
aka "consistent). This is useful in 2 scenarios:
- VLAN-unaware bridge ports will always encounter a miss in the VLAN
table. They should forward a packet as-is, though. So we use
"consistent" there. See commit e045124e93 ("net: dsa: mt7530: fix
tagged frames pass-through in VLAN-unaware mode").
- Traffic injected from the CPU port. The operating system is in god
mode; if it wants a packet to exit as VLAN-tagged, it sends it as
VLAN-tagged. Otherwise it sends it as VLAN-untagged*.
*This is true only if we don't consider the bridge TX forwarding offload
feature, which mt7530 doesn't support.
So for now, make the CPU port always stay in "consistent" mode to allow
software VLANs to be forwarded to their egress ports with the VLAN tag
intact, and not stripped.
Link: https://lore.kernel.org/netdev/trinity-e6294d28-636c-4c40-bb8b-b523521b00be-1674233135062@3c-app-gmx-bs36/
Fixes: e045124e93 ("net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230205140713.1609281-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When NET_DSA_MICROCHIP_KSZ_COMMON is built-in but PTP is a loadable
module, the ksz_ptp support still causes a link failure:
ld.lld-16: error: undefined symbol: ptp_clock_index
>>> referenced by ksz_ptp.c
>>> drivers/net/dsa/microchip/ksz_ptp.o:(ksz_get_ts_info) in archive vmlinux.a
This can happen if NET_DSA_MICROCHIP_KSZ8863_SMI is enabled, or
even if none of the KSZ9477_I2C/KSZ_SPI/KSZ8863_SMI ones are active
but only the common module is.
The most straightforward way to address this is to move the
dependency to NET_DSA_MICROCHIP_KSZ_PTP itself, which can now
only be enabled if both PTP_1588_CLOCK support is reachable
from NET_DSA_MICROCHIP_KSZ_COMMON. Alternatively, one could make
NET_DSA_MICROCHIP_KSZ_COMMON a hidden Kconfig symbol and extend the
PTP_1588_CLOCK_OPTIONAL dependency to NET_DSA_MICROCHIP_KSZ8863_SMI as
well, but that is a little more fragile.
Fixes: eac1ea2026 ("net: dsa: microchip: ptp: add the posix clock support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230130131808.1084796-1-arnd@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add control of an external VSC7512 chip.
Currently the four copper phy ports are fully functional. Communication to
external phys is also functional, but the SGMII / QSGMII interfaces are
currently non-functional.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the Felix driver would probe the ports and verify functionality, it
would fail if it hit single port mode that wasn't supported by the driver.
The initial case for the VSC7512 driver will have physical ports that
exist, but aren't supported by the driver implementation. Add the
OCELOT_PORT_MODE_NONE macro to handle this scenario, and allow the Felix
driver to continue with all the ports that are currently functional.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The architecture around the VSC7512 differs from existing felix drivers. In
order to add support for all the chip's features (pinctrl, MDIO, gpio) the
device had to be laid out as a multi-function device (MFD).
One difference between an MFD and a standard platform device is that the
regmaps are allocated to the parent device before the child devices are
probed. As such, there is no need for felix to initialize new regmaps in
these configurations, they can simply be requested from the parent device.
Add support for MFD configurations by performing this request from the
parent device.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The define FELIX_MAC_QUIRKS was used directly in the felix.c shared driver.
Other devices (VSC7512 for example) don't require the same quirks, so they
need to be configured on a per-device basis.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert qca8k to regmap read/write bulk API. The mgmt eth can write up
to 32 bytes of data at times. Currently we use a custom function to do
it but regmap now supports declaration of read/write bulk even without a
bus.
Drop the custom function and rework the regmap function to this new
implementation.
Rework the qca8k_fdb_read/write function to use the new
regmap_bulk_read/write as the old qca8k_bulk_read/write are now dropped.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and use QCA8K_ATU_TABLE_SIZE instead of hardcoding the ATU size with
a pure number and using sizeof on the array.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The build system currently complains:
scripts/Makefile.build:252: drivers/net/dsa/ocelot/Makefile:
felix.o is added to multiple modules: mscc_felix mscc_seville
Since felix.c holds the DSA glue layer, create a mscc_felix_dsa_lib.ko.
This is similar to how mscc_ocelot_switch_lib.ko holds a library for
configuring the hardware.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20230125145716.271355-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KSZ9477, KSZ9567, KSZ9563, KSZ8563 and LAN937x supports Credit based
shaper. To differentiate the chip supporting cbs, tc_cbs_supported
flag is introduced in ksz_chip_data.
And KSZ series has 16bit Credit increment registers whereas LAN937x has
24bit register. The value to be programmed in the credit increment is
determined using the successive multiplication method to convert decimal
fraction to hexadecimal fraction.
For example: if idleslope is 10000 and sendslope is -90000, then
bandwidth is 10000 - (-90000) = 100000.
The 10% bandwidth of 100Mbps means 10/100 = 0.1(decimal). This value has
to be converted to hexa.
1) 0.1 * 16 = 1.6 --> fraction 0.6 Carry = 1 (MSB)
2) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
3) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
4) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
5) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
6) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9 (LSB)
Now 0.1(decimal) becomes 0.199999(Hex).
If it is LAN937x, 24 bit value will be programmed to Credit Inc
register, 0x199999. For others 16 bit value will be prgrammed, 0x1999.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LAN937x family of switches has 8 queues per port where the KSZ switches
has 4 queues per port. By default, only one queue per port is enabled.
The queues are configurable in 2, 4 or 8. This patch add 8 number of
queues for LAN937x and 4 for other switches.
In the tag_ksz.c file, prioirty of the packet is queried using the skb
buffer and the corresponding value is updated in the tag.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Starting with commit eee16b1471 ("net: dsa: microchip: perform the
compatibility check for dev probed"), the KSZ switch driver now bails
out if it thinks the DT compatible doesn't match the actual chip ID
read back from the hardware:
ksz9477-switch 1-005f: Device tree specifies chip KSZ9893 but found
KSZ8563, please fix it!
For the KSZ8563, which used ksz_switch_chips[KSZ9893], this was fine
at first, because it indeed shares the same chip id as the KSZ9893.
Commit b449080956 ("net: dsa: microchip: add separate struct
ksz_chip_data for KSZ8563 chip") started differentiating KSZ9893
compatible chips by consulting the 0x1F register. The resulting breakage
was fixed for the SPI driver in the same commit by introducing the
appropriate ksz_switch_chips[KSZ8563], but not for the I2C driver.
Fix this for I2C-connected KSZ8563 now to get it probing again.
Fixes: b449080956 ("net: dsa: microchip: add separate struct ksz_chip_data for KSZ8563 chip").
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230120110933.1151054-1-a.fatoum@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Felix (VSC9959) has a DEV_GMII:MM_CONFIG block composed of 2 registers
(ENABLE_CONFIG and VERIF_CONFIG). Because the MAC Merge statistics and
pMAC statistics are already in the Ocelot switch lib even if just Felix
supports them, I'm adding support for the whole MAC Merge layer in the
common Ocelot library too.
There is an interrupt (shared with the PTP interrupt) which signals
changes to the MM verification state. This is done because the
preemptible traffic classes should be committed to hardware only once
the verification procedure has declared the link partner of being
capable of receiving preemptible frames.
We implement ethtool getters and setters for the MAC Merge layer state.
The "TX enabled" and "verify status" are taken from the IRQ handler,
using a mutex to ensure serialized access.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix VSC9959 switch supports frame preemption and has a MAC Merge
layer. In addition to the structured stats that exist for the eMAC,
export the counters associated with its pMAC (pause, RMON, MAC, PHY,
control) plus the high-level MAC Merge layer stats. The unstructured
ethtool counters, as well as the rtnl_link_stats64 were left to report
only the eMAC counters.
Because statistics processing is quite self-contained in ocelot_stats.c
now, I've opted for introducing an ocelot->mm_supported bool, based on
which the common switch lib does everything, rather than pushing the
TSN-specific code in felix_vsc9959.c, as happens for other TSN stuff.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO core should not pass a C45 request via the C22 API call any
more. So remove the tests from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While the prior patch moved the adjust_link code into the
phylink_mac_link_up api, this patch cleans it up and adds the setting the
port's flow control based on the phylink_mac_link_up input parameters.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the adjust_link api with the phylink apis that provide
equivalent functionality.
The remaining functionality from the adjust_link is now covered in the
phylink_mac_link_up api.
Removes:
.adjust_link
Adds:
.phylink_get_caps
.phylink_mac_link_up
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparing to move the adjust_link logic into the phylink_mac_link_up
api, change the macro used to check for the cpu port. In
phylink_mac_link_up, the phydev pointer passed in for the CPU port is
NULL, so we can't keep using phy_is_pseudo_fixed_link(phydev).
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the regmap_write() is over a slow bus that will sleep, we can speed up
the boot-up time a bit by not bothering to clear a bit that is already
clear.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
