If we connect Male-A-To-Male-A cable between otg-host and host pc,
the ci->vbus_active is set wrongly, and cause the controller run
at peripheral mode when we load gadget module (ci_udc_start will be run),
but the software runs at host mode due to id = 0. The ehci_irq
can't handle suspend (USBi_SLI) interrupt which is enabled for
peripheral mode, it causes no one will handle irq error.
This patch is needed for 3.12 stable
Cc: stable <stable@vger.kernel.org>
Acked-by: Michael Grzeschik <mgr@pengutronix.de>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 40ed51a4b (usb: chipidea: host: add vbus regulator
control) introduced a smatch complaint because regulator_disable() is called
without checking whether ci->platdata->reg_vbus is not NULL.
Fix this by adding the check.
This patch is needed for 3.12 stable
Cc: stable <stable@vger.kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ZTE AC2726 EVDO modem drops ppp connection every minute when driven by
zte_ev but works fine when driven by option. Move the support for AC2726
back to option driver.
Signed-off-by: Dmitry Kunilov <dmitry.kunilov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use usb_add_phy_dev instead of usb_add_phy, so that devices can
be bound to the phy. This is needed to set up USB phy for
some internal PCI USB host controllers on R-Car Gen2.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 learned that it can't resume a PHY which wasn't
initialized and it also learned to not leave PHY powered
up in case of an error.
twl6030-usb PHY driver got a fix for a signedness bug in
twl6030_readb().
Tegra PHY driver got a bug fix where it could return success
even though there was an error.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=MfzU
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.13-rc4
DWC3 learned that it can't resume a PHY which wasn't
initialized and it also learned to not leave PHY powered
up in case of an error.
twl6030-usb PHY driver got a fix for a signedness bug in
twl6030_readb().
Tegra PHY driver got a bug fix where it could return success
even though there was an error.
Signed-of-by: Felipe Balbi <balbi@ti.com>
the lock was only taken inside the hardirq
handler, which runs with IRQs disabled. There's
no chance of any race condition happening, even
on SMP machines. It's safe to remove that
spinlock.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 614ced91fc.
The units on this was seen were prototypes and the issue is
not seen on younger units.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Individual controller driver has different requirement for wakeup
setting, so move it from core to itself. In order to align with
current etting the default wakeup setting is enabled (except for
chipidea host).
Pass compile test with below commands:
make O=outout/all allmodconfig
make -j$CPU_NUM O=outout/all drivers/usb
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds i.MX51 as the next user of the usbmisc driver.
Functionality is similar to i.MX53, so at this stage simply
reuse existing i.MX53 calls.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds i.MX27 and i.MX31 as the next user of the usbmisc driver.
Tested-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ci_hdrc_imx's probe needs usbmisc_imx to be loadded beforehand,
so it is better we load usbmisc_imx first.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regmap only needs to reallocate if the hw_read on the CAP register shows
lpm is used. Therefore the if() statement check the change.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use PCI standard marco dev_is_pci() instead of directly compare
pci_bus_type to check whether it is pci device.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds external USB phy support to USB HCD driver that
allows to find and initialize external USB phy, bound to
the HCD, when the HCD is added.
The usb_add_hcd function returns -EPROBE_DEFER if the USB
phy, bound to the HCD, is not ready.
If no USB phy is bound, the HCD is initialized as usual.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds remove_phy flag to the HCD structure. If the flag is
set and if hcd->phy is valid, the phy is shutdown and released
whenever usb_add_hcd fails or usb_hcd_remove is called.
This can be used by the HCD drivers to auto-remove
the external USB phy when it is no longer needed.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have sg_miter_* APIs for accessing scsi sg buffer, so
use them to make code clean and bug free.
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add more info to debug prints in urb_unlink path
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add calls to usb_hcd_link_urb_to_ep, usb_hcd_unlink_urb_from_ep, and
usb_hcd_check_unlink_urb in the appropriate locations.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-spear glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-spear suspend scenario.
Calling explicitly the ohci_suspend() routine in
spear_ohci_hcd_drv_suspend() will ensure proper
handling of suspend scenario.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-exynos glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-exynos suspend scenario.
Calling explicitly the ohci_suspend() routine in
exynos_ohci_suspend() will ensure proper handling of suspend
scenario.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-da8xx glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-da8xx suspend scenario.
Calling explicitly the ohci_suspend()
routine in ohci_da8xx_suspend() will ensure proper
handling of suspend scenario.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-usb@vger.kernel.or
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-s3c2410 glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-s3c2410 suspend scenario.
Calling explicitly the ohci_suspend()
routine in ohci_hcd_s3c2410_drv_suspend() will ensure
proper handling of suspend scenario.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-at91 glue was not properly handled
as it was not suspending generic part of ohci controller. Alan Stern
suggested, properly handle ohci-at91 suspend scenario.
Calling explicitly the ohci_suspend() routine in ohci_hcd_at91_drv_suspend()
will ensure proper handling of suspend scenario. This task is sugested
by Alan Stern.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of OHCI was not properly
handled in ochi_suspend()routine. Alan Stern
suggested, properly handle OHCI suspend scenario.
This does generic proper handling of suspend
scenario to all OHCI SOC.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit "usb: usbtest: support bos descriptor test for usb 3.0"
introduced a test for bos descriptor. And USB 2.1 device also can be
checked. So this patch extends the test coverage to support USB 2.1 device.
Reported-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 2.1 Link PM adds to use bits[1:15] according to USB 2.0 ECN Errata for
Link Power Management spec.
Bit Encoding
0 Reserved
1 LPM
2 BESL & Altemate HIRD definitions supported
3 Recommended Baseline BESL valid
4 Recommended Deep BESL valid
11:8 Recommended Baseline BESL value
15:12 Recommended Deep BESL value
31:16 Reserved
So fix the bit mask from 0x1e to 0xfffe.
Reported-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Test 10 of usbtest module, it queues multiple control messages and
thereby tests control message queuing, protocol stalls, short reads, and
fault handling. And this patch add a test case to support queue BOS control
request for USB 3.0 SPEC.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the .find_device function pointer in struct acpi_bus_type
with a new one, .find_companion, that is supposed to point to a
function returning struct acpi_device pointer (instead of an int)
and takes one argument (instead of two). This way the role of
this callback is more clear and the implementation of it can
be more straightforward.
Update all of the users of struct acpi_bus_type (PCI, PNP/ACPI and
USB) to reflect the structure change.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Lan Tianyu <tianyu.lan@intel.com> # for USB/ACPI
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add Tahvo USB transceiver driver.
Based on old code from linux-omap tree. The original driver was written
by Juha Yrjölä, Tony Lindgren, and Timo Teräs.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Transceivers need to manage OTG controller state on OMAP1 to enable
switching between peripheral and host modes. Provide a driver for that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: phy-tegra-usb.c: wrong pointer check for remap UTMI
A wrong pointer was used to test the result of devm_ioremap()
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/host/ehci-mv.c:181:26-27: WARNING comparing pointer to 0, suggest !E
/c/kernel-tests/src/cocci/drivers/usb/host/ehci-mv.c:181:26-27: WARNING comparing pointer to 0
Compare pointer-typed values to NULL rather than 0
Semantic patch information:
This makes an effort to choose between !x and x == NULL. !x is used
if it has previously been used with the function used to initialize x.
This relies on type information. More type information can be obtained
using the option -all_includes and the option -I to specify an
include path.
Generated by: coccinelle/null/badzero.cocci
CC: Jingoo Han <jg1.han@samsung.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
This patch adds a check for USB_STATE_NOTATTACHED to the
hub_port_warm_reset_required() workaround for ports that end up in
Compliance Mode in hub_events() when trying to decide which reset
function to use. Trying to call usb_reset_device() with a NOTATTACHED
device will just fail and leave the port broken.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include linux/dma-mapping.h to make the new functions available that are
used since 22d9d8e83 ("DMA-API: usb: use dma_set_coherent_mask()").
drivers/usb/host/ohci-pxa27x.c: In function ‘ohci_pxa_of_init’:
drivers/usb/host/ohci-pxa27x.c:310:2: error: implicit declaration of function ‘dma_coerce_mask_and_coherent’ [-Werror=implicit-function-declaration]
drivers/usb/host/ohci-pxa27x.c:310:2: error: implicit declaration of function ‘DMA_BIT_MASK’ [-Werror=implicit-function-declaration]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the drivers that no longer need it, it is removed.
It is removed from the Makefile. Drivers not fully converted
to dynamic debug have it shifted down into the individual
drivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With dynamic debugging this log level is no longer supported.
The decision which messages are interesting is done in user space.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows removal of much conditional compilation.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a step in the conversion to only use dynamic
debugging.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That logging is overkill. Simply remove it.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These helpers are used only during setup of a HCD.
A small overhead is no problem.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes sure the header files are all there
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow a full switch to dynamic debugging make the
debug parameter conditional on defined(DEBUF) || defined(CONFIG_DYNAMIC_DEBUG)
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This gets rid of conditional compilation.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The decision what is interesting is shifted to user space by
dynamic debugging.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The decision what is interesting is made in user space.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For dynamic debug the overhead for evaluating parameters must
be sacrificed only if the message is actually printed
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simply remove the conditional compilation and remove
the empty stubs.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simple elemination of the conditional compilation
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With dynamic debugging the selection is done in user space
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the introduction of dynamic debugging it has become redundant.
Collapse it with ohci_dbg()
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conditional compilation for debugging is removed in favor of
dynamic debugging. To do so
1. the support for debugfs is always compiled
2. the support for the ancient print_urb debugging aid is removed
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An ioctl that does depends on communication with a device should
prevent suspension of teh device.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simple straightforward implementation. Just returning the statistics
gathered for TIOCMIWAIT
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This implements TIOCMIWAIT for TIOCM_DSR, TIOCM_RI and TIOCM_CD
Disconnect is handled as TIOCM_CD or an error.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 40ed51a4b (usb: chipidea: host: add vbus regulator
control) introduced a smatch complaint because regulator_disable() is called
without checking whether ci->platdata->reg_vbus is not NULL.
Fix this by adding the check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the CS5 setting on the PL2303 USB-to-serial devices. CS5 has a
value of 0 and the CSIZE setting has been skipped altogether by the enclosing
if. Tested on 3.11.6 and the scope shows the correct output after the fix has
been applied.
Tagged to be added to stable, because it fixes a user visible driver bug and is
simple enough to backport easily.
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FTDI UARTs support only 7 or 8 data bits. Until now the ftdi_sio driver would
only report this limitation for CS6 to dmesg and fail to reflect this fact to
tcgetattr.
This patch reverts the unsupported CSIZE setting and reports the fact with less
severance to dmesg for both CS5 and CS6.
To test the patch it's sufficient to call
stty -F /dev/ttyUSB0 cs5
which will succeed without the patch and report an error with the patch
applied.
As an additional fix this patch ensures that the control request will always
include a data bit size.
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes an erroneous check of CSIZE, which made it impossible to set
CS5.
Compiles clean, but couldn't test against hardware.
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes an erroneous check of CSIZE, which made it impossible to set
CS5.
Compiles clean, but couldn't test against hardware.
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When multiple wireless USB devices are connected and one of the devices
disconnects, the host will distribute a new group key to the remaining
devicese using wusbhc_gtk_rekey. wusbhc_gtk_rekey takes the
wusbhc->mutex and holds it while it submits a URB to set the new key.
This causes a deadlock in wa_urb_enqueue when it calls a device lookup
helper function that takes the same lock.
This patch changes wusbhc_gtk_rekey to submit a work item to set the GTK
so that the URB is submitted without holding wusbhc->mutex.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch modifies the device notification handler to not look up the
wusb_dev object before it calls the lower-level handler routines since
the wusbhc mutex is not held when calling those routines and the device
could go away in the meantime. Instead, let the individual notification
handlers get the device ptr if they need to after they have taken the
mutex.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch modifies the WUSB device disconnect timer code to send
keepalives to all connected devices even if they are not authenticated.
This fixes a problem where unauthenticated devices that lose their
connection before they are authenticated will stay in the device tree
forever. More importantly, devices in this situation will never
relinquish their port on the root hub so eventually all root ports will
be taken up and no other devices can connect.
A comment in the existing code states that there are some devices that
may not respond to keepalives if they have not been authenticated. That
comment is about 5 years old and I don't know of any WUSB devices that
act that way. Either way, any buggy devices that may still be around
will continue to work as long as they can transition to the
authenticated state within the WUSB LOA timeout of 4s, which is not
unreasonable to expect.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceProtocol value.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface 1 on this device isn't for option to bind to otherwise an oops
on usb_wwan with log flooding will happen when accessing the port:
tty_release: ttyUSB1: read/write wait queue active!
It doesn't seem to respond to QMI if it's added to qmi_wwan so don't add
it there - it's likely used by the card reader.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function xhci_write_64() is used to write 64bit xHC registers residing in MMIO.
On 32bit systems, xHC registers need to be written with 32bit accesses by
writing first the lower 32bits and then the higher 32bits. The header file
asm-generic/io-64-nonatomic-lo-hi.h ensures that on 32bit systems writeq() will
will write 64bit registers in 32bit chunks with low-high order.
Replace all calls to xhci_write_64() with calls to writeq().
This is done to reduce code duplication since 64bit low-high write logic
is already implemented and to take advantage of inherent "atomic" 64bit
write operations on 64bit systems.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Function xhci_read_64() is used to read 64bit xHC registers residing in MMIO.
On 32bit systems, xHC registers need to be read with 32bit accesses by
reading first the lower 32bits and then the higher 32bits.
Replace all calls to xhci_read_64() with calls to readq() and include
asm-generic/io-64-nonatomic-lo-hi.h header file, so that if the system
is not 64bit, readq() will read registers in 32bit chunks with low-high order.
This is done to reduce code duplication since 64bit low-high read logic
is already implemented and to take advantage of inherent "atomic" 64bit
read operations on 64bit systems.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Function xhci_writel() is used to write a 32bit value in xHC registers residing
in MMIO address space. It takes as first argument a pointer to the xhci_hcd
although it does not use it. xhci_writel() internally simply calls writel().
This creates an illusion that xhci_writel() is an xhci specific function that
has to be called in a context where a pointer to xhci_hcd is available.
Remove xhci_writel() wrapper function and replace its calls with calls to
writel() to make the code more straight-forward.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Function xhci_readl() is used to read 32bit xHC registers residing in MMIO
address space. It takes as first argument a pointer to the xhci_hcd although
it does not use it. xhci_readl() internally simply calls readl(). This creates
an illusion that xhci_readl() is an xhci specific function that has to be
called in a context where a pointer to xhci_hcd is available.
Remove the unnecessary xhci_readl() wrapper function and replace its calls to
with calls to readl() to make the code more straightforward.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch removes the to_pci_dev() conversion performed to generic struct
device since it is not actually useful (the pointer to the generic device
can be used directly rather through a conversion to pci_dev) and it is pci
bus specific.
This isn't stable material because this code will produce harmless
behavior on non-PCI xHCI hosts. The pci_device pointer is never
dereferenced, only used to re-calculate the underlying device pointer.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The fields 'add_flags' and 'drop_flags' in struct xhci_input_control_ctx
have type __le32 and need to be converted to CPU byteorder before being
used to derive the number of dropped endpoints.
This bug was found using sparse.
This patch is not suitable for stable, since the bug would only be
triggered on big endian systems, and the code only runs for Intel xHCI
host controllers, which are always integrated into little endian
systems.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The fields 'add_flags' and 'drop_flags' in struct xhci_input_control_ctx
have type __le32 and need to be converted to CPU byteorder before being
used to derive the number of added endpoints.
This bug was found using sparse.
This patch is not suitable for stable, since the bug would only be
triggered on big endian systems, and the code only runs for Intel xHCI
host controllers, which are always integrated into little endian
systems.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch removes the unneccessary check 'if (stream_info)' because
there is already a check few lines above which ensures that stream_info
is not NULL.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
SCT_FOR_CTX(p) is defined as (((p) << 1) & 0x7) in which case if we want
to set the stream context type to SCT_SSA_256 i.e 0x7 (although secondary
stream arrays are not yet supported) using this macro definition we will
get actually 0x6 which is not what we want.
This patch fixes the above issue by defining the SCT_FOR_CTX(p) macro as
(((p) & 0x7) << 1)
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch replaces USB_MAXINTERFACES with config->desc.bNumInterface in
the termination condition for the loop that updates the LPM timeout of the
endpoints on the cofiguration's interfaces, in xhci_calculate_lpm_timeout(),
to avoid unnecessary loop cycles since most configurations come with 1-2
interfaces while USB_MAXINTERFACES is 32.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The field 'dev_info' in struct xhci_slot_ctx has type __le32 and it needs
to be converted to CPU byteorder for the correct retrieval of its subfield
'Context Entries'. This field is used by the trace event 'xhci_address_ctx'
to trace only the contexts of valid endpoints.
This bug was found using sparse.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch fixes the following sparse warnings:
drivers/usb/host/./xhci-trace.h:116:1: warning: cast to restricted __le32
drivers/usb/host/./xhci-trace.h:116:1: warning: cast to restricted __le32
drivers/usb/host/./xhci-trace.h:116:1: warning: restricted __le32 degrades to
integer
drivers/usb/host/./xhci-trace.h:116:1: warning: restricted __le32 degrades to
integer
by converting the field 'trb' of the trace buffer entry structure from array
with elements of type __le32 to an array with elements of type u8.
Into the trb array are copied the contents of the TRB that generated the event.
The trace-cmd tool with the help of plugin_xhci.py will use this field to
parse the TRB contents in a human readable way.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch fixes the retrieval of the DMA address of the TRB that generated
the event by converting the field[0] (low address bits) and field[1] (high
address bits) to CPU byteorder and then typecasting field[1] to u64 so that
the bitshift will not lead to overflow.
In the original code, the typecasting of le32 to u64 was incorrect and the
subsequent conversion to le64 reverts the low and high address parts.
This bug was found using sparse.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch converts Event TRB's 3rd field, which has type le32, to CPU
byteorder before using it to retrieve the Slot ID with TRB_TO_SLOT_ID macro.
This bug was found using sparse.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch converts TRB_CYCLE to le32 to update correctly the Cycle Bit in
'control' field of the link TRB.
This bug was found using sparse.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Section 4.11.7.1 of rev 1.0 of the xhci specification states that a link TRB
can only occur at a boundary between underlying USB frames (512 bytes for
high speed devices).
If this isn't done the USB frames aren't formatted correctly and, for example,
the USB3 ethernet ax88179_178a card will stop sending (while still receiving)
when running a netperf tcp transmit test with (say) and 8k buffer.
This should be a candidate for stable, the ax88179_178a driver defaults to
gso and tso enabled so it passes a lot of fragmented skb to the USB stack.
Notes from Sarah:
Discussion: http://marc.info/?l=linux-usb&m=138384509604981&w=2
This patch fixes a long-standing xHCI driver bug that was revealed by a
change in 3.12 in the usb-net driver. Commit
638c5115a7 "USBNET: support DMA SG" added
support to use bulk endpoint scatter-gather (urb->sg). Only the USB
ethernet drivers trigger this bug, because the mass storage driver sends
sg list entries in page-sized chunks.
This patch only fixes the issue for bulk endpoint scatter-gather. The
problem will still occur for periodic endpoints, because hosts will
interpret no-op transfers as a request to skip a service interval, which
is not what we want.
Luckily, the USB core isn't set up for scatter-gather on isochronous
endpoints, and no USB drivers use scatter-gather for interrupt
endpoints. Document this known limitation so that developers won't try
to use urb->sg for interrupt endpoints until this issue is fixed. The
more comprehensive fix would be to allow link TRBs in the middle of the
endpoint ring and revert this patch, but that fix would touch too much
code to be allowed in for stable.
This patch should be backported to kernels as old as 3.12, that contain
the commit 638c5115a7 "USBNET: support DMA
SG". Without this patch, the USB network device gets wedged, and stops
sending packets. Mark Lord confirms this patch fixes the regression:
http://marc.info/?l=linux-netdev&m=138487107625966&w=2
Signed-off-by: David Laight <david.laight@aculab.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Mark Lord <mlord@pobox.com>
Cc: stable@vger.kernel.org
This patch moves at91_pmc.h header from machine specific directory
(arch/arm/mach-at91/include/mach/at91_pmc.h) to clk include directory
(include/linux/clk/at91_pmc.h).
We need this to avoid reference to machine specific headers in clk
drivers.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Cc: linux-usb@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
First set of fixes for this -rc cycle. A few important
fixes which should be backported to stable kernels and
the usual set of sparse warning fixes. There's also a
regression fix on phy-generic.c which would prevent
am335x-based platforms from having their PHY drivers
probed.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJSk5HFAAoJEIaOsuA1yqRE7xoP/Rz2ZMt1BlRH3rHorQL+0mqs
2KDN7Vz+vLlt4BldLYiMpKTe7zTmV28yR+MaTHzX1RVJEXJl0/hJVPvOmOdAPAkX
Y5KnjWrUNhrG6ChxUwaJslWLA8ACnV5PwdQDsSJYGKAi0jWuXE0qSJoGqX8PgJX/
gU9TK5iWHFflmkpg8M8UPx2XyMFHYfonJ6Nh2A8bYTkHqHFZp/CoCZKQqmAathKg
9Kyze3elKyA5Ch1JXf++WIViCXMkNRgWp4YNYUDj9t32mw2iLyg0czMvTNK0OqeR
ICqzz4EgiSQjFq4p70kJSDXqRUGIre/JcZk7Gq3zAAUw0ScuJRQOZBmDiyu5K2vk
UG+H05YZCFXqr4e+80WoIzLyaZzokOA/RI9sDPKeF3NvaxCCtf9BsEu4ugOwoBrz
9MQhHJBcvJAYbBeUy/L80btL7SoSc76mQ08+HImeDoolZMFgVcS0bUTPE0VSwW9U
oDnOAe/kSCRSZPEkDp6nbKqp3OX1tvWA+1bsYslsEbPotnulYWawd4OCPhPWKc2J
Uu6HBC6aDZ6DS3YH/GKkJONV3oRjaqjDwHMoTlZa3bDftPACzGgXc+r8s4iiLzya
VHK5R8JK32hD/GI/5oWhJVgDQmFbp2Kk6MeSTT1AgiJ75x7Z1dWncePohdaPrMt/
Wn19N0Ype+72HhTZ3oP2
=ZzE5
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.13-rc2
First set of fixes for this -rc cycle. A few important
fixes which should be backported to stable kernels and
the usual set of sparse warning fixes. There's also a
regression fix on phy-generic.c which would prevent
am335x-based platforms from having their PHY drivers
probed.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Add support for using the sourcesink function in gadgets composed with
configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for using the loopback USB function in gadgets composed with
configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
alloc_ep_req() is a function repeated in several modules.
Make a common implementation and use it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If there are setup requests not directed to an endpont or an interface,
current config's setup() has been attempted so far.
This patch, in case the above fails, adds code which tries the setup() of
configuration's function if there is only one function in the configuration.
This behavior is required to provide equivalent of gadget zero with configfs.
The gadget zero has a "config driver" for sourcesink, but all it does is
delegating the request to the function proper. So when the equivalent gadget
is set up with configfs it needs to handle requests directed to
"config driver", but with configfs it is not possible to specify
"config drivers".
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Only start the otg_timer in dual role mode; otherwise in peripheral mode
when musb is disconnected from the host port, otg_timer starts and
continuously toggles the session, which causes VBUS pulse.
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes dependency on Freescale USB UTG Transceiver
driver and makes OTG FSM implementation selectable.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Other USB drivers may want to use OTG final state machine
implementation, so make this header available for them.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
OTG Final State Machine calls functions which may sleep.
For example, start_gadget callback implementation can use
usb_gadget_vbus_connect(), whose context: can sleep.
If so, mutex should be used instead of spinlock.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
if this header is included twice, we would have
redefinition build errors. Fix this.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this header uses spinlocks and errno values, so
we must include <linux/spinlock.h> and <linux/errno.h>
to avoid build errors.
Signed-off-by: Felipe Balbi <balbi@ti.com>
These functions used to return negative errror codes but now they return
ERR_PTRs.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The stop_activity function never uses driver argument (even
though it modifies it) and thus it is safe to remove it.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dsps platform needs to save save some registers at suspend time and
restore them after resume. This patch adds a struct for these registers,
and also lets the musb core know that the core registers need to be
saved as well.
We also have to explicitly de-assert the port reset upon resume on this
platform, but musb_port_reset() should not be called from glue layers.
Hence, introduce a flag in struct musb_hdrc_config for this.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
rx_mode and tx_mode need to be read at suspend time and restored on
resume for dsps platforms. So add it to the wrapper struct first, and
initialize the values.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make musb_port_suspend() externally available, and call it when to host
goes into suspend. This allows the core to go into suspend while a
device is connected.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It appears not all platforms featuring a musb core need to save the musb
core registers at suspend time and restore them on resume.
The dsps platform does, however, and because it shouldn't cause any
trouble on other platforms, do it unconditionally for all of them.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to inter dependencies of I2C and extcon by the time dwc3
checks for extcon device its not registered especially in case of J6.
In O5 the vbus regulator save us from getting to this point.
So for tiime being return PROBE_DEFER if extcon is enabled in dt.
Signed-off-by: George Cherian <george.cherian@ti.com>
this will let us support broken designs such
as AM335x EVM SK where ID pin isn't routed
anywhere on a host port.
With this we can toggle internal IDDIG signal
and make sure MUSB goes into host mode as
necessary.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Cc: Felipe Balbi <balbi@ti.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"ret" needs to be signed for the error handling to work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usb phy was power'ed on but was never power'ed off in the error path.
Fix it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usb_phy_set_suspend(phy, 0) is called before usb_phy_init. Fix it.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Call try_to_freeze() in sleep_thread() only when it's safe to sleep.
do_read() and do_write() calls sleep_thread with lock held.
Make sure these won't call try_to_freeze() by passing can_freeze flag
to sleep_thread.
Calling try_to_freeze() with a lock hold was done since day one in
f_mass_storage but since commit 0f9548ca1 ("lockdep: check that no
locks held at freeze time") lockdep complains about it.
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
that symbol is only used inside this function driver,
we should mark it static. Fixes sparse's:
drivers/usb/gadget/tcm_usb_gadget.c:373:6: warning: symbol \
'bot_cleanup_old_alt' was not declared. Should it \
be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
g_zero's module parameters can, and should, be
static. This fixes sparse warnings.
Cc: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fsg_common_set_inquiry_string() expects pointers
as second and third argument. Let's fix that by
passing NULL instead of plain 0 just so we silence
sparse's:
drivers/usb/gadget/f_mass_storage.c:3114:60: warning: \
Using plain integer as NULL pointer
drivers/usb/gadget/f_mass_storage.c:3114:63: warning: \
Using plain integer as NULL pointer
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of error, the function platform_device_register_simple() returns
ERR_PTR() and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc3 UDC driver doesn't implement endpoint wedging correctly.
When an endpoint is wedged, the gadget driver should be allowed to
clear the wedge by calling usb_ep_clear_halt(). Only the host is
prevented from resetting the endpoint.
This patch fixes the implementation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Pratyush Anand <pratyush.anand@st.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mass storage gadget returns DELAYED_STATUS in stead of
USB_GADGET_DELAYED_STATUS while handling bulk reset request. Since
peripheral driver uses USB_GADGET_DELAYED_STATUS for delayed status
handling, therefore replace DELAYED_STATUS by USB_GADGET_DELAYED_STATUS
in mass storage driver.
Since, DELAYED_STATUS and hence EP0_BUFSIZE will no longer be used now,
so remove them.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Cc: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Legacy gadgets supporting mass storage (g_mass_storage, g_acm_ms, g_multi)
all depend on BLOCK.
Make the standalone compilation of f_mass_storage (without any legacy
gadget) dependent no BLOCK, too.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to set mxs_phy rather as the platform drvdata so that we can get
the correct mxs_phy in mxs_phy_remove().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since commit c5340bd14 ("usb: musb: cancel work on removal") the workqueue
is cancelled but then if we bail out before the workqueue is setup we
get this:
|INFO: trying to register non-static key.
|the code is fine but needs lockdep annotation.
|turning off the locking correctness validator.
|CPU: 0 PID: 708 Comm: modprobe Not tainted 3.12.0+ #435
|[<c00867bc>] (lock_acquire+0xf0/0x108) from [<c00529d0>] (flush_work+0x38/0x2ec)
|[<c00529d0>] (flush_work+0x38/0x2ec) from [<c0052d24>] (__cancel_work_timer+0xa0/0x134)
|[<c0052d24>] (__cancel_work_timer+0xa0/0x134) from [<bf0e4ae4>] (musb_free+0x40/0x60 [musb_hdrc])
|[<bf0e4ae4>] (musb_free+0x40/0x60 [musb_hdrc]) from [<bf0e5364>] (musb_probe+0x678/0xb78 [musb_hdrc])
|[<bf0e5364>] (musb_probe+0x678/0xb78 [musb_hdrc]) from [<c0294bf0>] (platform_drv_probe+0x1c/0x24)
|[<c0294bf0>] (platform_drv_probe+0x1c/0x24) from [<c0293970>] (driver_probe_device+0x90/0x224)
|[<c0293970>] (driver_probe_device+0x90/0x224) from [<c0291ef0>] (bus_for_each_drv+0x60/0x8c)
|[<c0291ef0>] (bus_for_each_drv+0x60/0x8c) from [<c02938bc>] (device_attach+0x80/0xa4)
|[<c02938bc>] (device_attach+0x80/0xa4) from [<c0292b24>] (bus_probe_device+0x88/0xac)
|[<c0292b24>] (bus_probe_device+0x88/0xac) from [<c0291490>] (device_add+0x388/0x6c8)
|[<c0291490>] (device_add+0x388/0x6c8) from [<c02952a0>] (platform_device_add+0x188/0x22c)
|[<c02952a0>] (platform_device_add+0x188/0x22c) from [<bf11ea30>] (dsps_probe+0x294/0x394 [musb_dsps])
|[<bf11ea30>] (dsps_probe+0x294/0x394 [musb_dsps]) from [<c0294bf0>] (platform_drv_probe+0x1c/0x24)
|platform musb-hdrc.1.auto: Driver musb-hdrc requests probe deferral
|musb-hdrc musb-hdrc.1.auto: musb_init_controller failed with status -517
This patch moves the init part to earlier part so it can be cleaned as
part of the fail3 label because now it is surrounded by the fail4 label.
Step two is to remove it from musb_free() and add it to the two cleanup
paths (error path and device removal) separately.
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The delayed_status value is used to keep track of status response
packets on ep0. It needs to be reset or the set_config function would
still delay the answer, if the usb device got unplugged while waiting
for setup_continue to be called.
Cc: stable@vger.kernel.org
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The TX-complete interrupt of the CPPI41 on AM335x fires too early.
Adding a loop and counting how long it takes until the
MUSB_TXCSR_TXPKTRDY bit is cleared I see
FS:
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1
|cppi41_dma_callback() 74 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1
|cppi41_dma_callback() 66 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1
|cppi41_dma_callback() 136 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1
|cppi41_dma_callback() 136 loops
avg: 110 - 150us
HS:
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1
|cppi41_dma_callback() 0 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1
|cppi41_dma_callback() 2 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1
|cppi41_dma_callback() 13 loops
avg: 2us
for the same test case. One loop means a udelay(1). The delay seems to
depend on the packet size. On HS the bit is always cleared for small
packet sizes while on FS it is never the case, it mostly around 110us.
This testing has been performed with g_ether (musb as device) and using BULK
transfers.
INTR transfers are way more fun: during init the gadget sends a INT
packet to the host and cppi41 says "transfer done" shortly after. The
MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host
did not try to receive it, it does so after the interface (on host side) has
been configured. Until this happens, that packet remains in musb's FIFO.
To fix this, two things are done:
- No DMA transfers for INT based endpoints. These transfer are usually
very small and rare so it is likely better to skip the DMA engine and
stuff the four bytes directly into the FIFO
- on HS we poll up to 25us and hope that bit goes away. If not we setup
a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS
the command
| ping 10.10.10.10 -c1 -s65130
creates about 44 1514bytes transfers. About 19 of them need a second
timer to complete.
Reported-by: Bin Liu <b-liu@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves most of the logic in cppi41_dma_callback() into
cppi41_trans_done() where it can be called from another function.
Instead of computing "transferred" (the number of bytes transferred in
the last transaction) in cppi41_trans_done() the member
"cppi41_channel->prog_len" is now set to 0 if the transfer as a whole
can be considered as done. If it is != 0 then the next iteration is
assumed.
This is a preparation for a workaround.
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix regression introduced by commit 818f60365a ("USB: serial: add
memory flags to usb_serial_generic_write_start"), which incorrectly used
GFP_KERNEL in write(), which must not not sleep.
Reported-by: Dave Jones <davej@fedoraproject.org>
Tested-by: Dave Jones <davej@fedoraproject.org>
Cc: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix race in generic write implementation, which could lead to
temporarily degraded throughput.
The current generic write implementation introduced by commit
27c7acf220 ("USB: serial: reimplement generic fifo-based writes") has
always had this bug, although it's fairly hard to trigger and the
consequences are not likely to be noticed.
Specifically, a write() on one CPU while the completion handler is
running on another could result in only one of the two write urbs being
utilised to empty the remainder of the write fifo (unless there is a
second write() that doesn't race during that time).
Cc: stable <stable@vger.kernel.org> # 2.6.35
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bd27fa44e1 (usb: phy: generic:
Don't use regulator framework for RESET line) introduced regression: All
users of usb_nop_xceiv_register() will fail because there is no platform
data and the default reset GPIO is 0 which is a valid GPIO. Fix that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The musb driver is usable in host, gadget or dual role mode depending
on the kernel configuration.
However, the musb gadget part of the driver is enabling OTG mode
whether the driver is built for dual role or gadget only mode. This
induces a bug for gadget only USB device controllers where the kernel
tries to use Host Negotiation Protocol with such controllers, which
causes a panic.
This behaviour is now fixed by enabling OTG mode only when musb driver
is built for dual role mode.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In commit
88f718e3fa
"ARM: pxa: delete the custom GPIO header"
we removed the implicit inclusion of <mach/gpio.h>
from <linux/gpio.h>.
The pxa25x_udc was not using that, but it was relying
on <linux/gpio.h> to implictly include <mach/gpio.h>
which in turn implicitly included <mach/hardware.h>,
which was needed for the driver to compile.
Fix this up by explicitly including the necessary
<mach/hardware.h> header.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves s3c_hsotg_disconnect function call from USBSusp interrupt
handler to SET_ADDRESS request handler.
It's because disconnected state can't be detected directly, because this
hardware doesn't support Disconnected interrupt for device mode. For both
Suspend and Disconnect events there is one interrupt USBSusp, but calling
s3c_hsotg_disconnect from this interrupt handler causes config reset in
composite layer, which is not undesirable for Suspended state.
For this reason s3c_hsotg_disconnect is called from SET_ADDRESS request
handler, which occurs always after disconnection, so we do disconnect
immediately before we are connected again. It's probably only way we
can do handle disconnection correctly.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds missing spinlock locking in s3c_hsotg_complete_setup function,
and unlocking for gadget setup call.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
instead of having each user of generic phy find
out about its own resources and pass it to the
core layer, have th core layer itself figure that
out. It's as simple as moving a piece of code
around. This fixes a big regression caused during
the merge window where am335x-based platforms
wouldn't be able to probe their PHY driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit [4d175f34: usb: phy: nop: Defer clock prepare until PHY init]
removed a goto reaching behind a “return ret” at the end of the function
thus removing the only possible way that statement could be reached, and
so rendering it a dead code. This commit cleans it up by removing said
dead code.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull SCSI target updates from Nicholas Bellinger:
"Things have been quiet this round with mostly bugfixes, percpu
conversions, and other minor iscsi-target conformance testing changes.
The highlights include:
- Add demo_mode_discovery attribute for iscsi-target (Thomas)
- Convert tcm_fc(FCoE) to use percpu-ida pre-allocation
- Add send completion interrupt coalescing for ib_isert
- Convert target-core to use percpu-refcounting for se_lun
- Fix mutex_trylock usage bug in iscsit_increment_maxcmdsn
- tcm_loop updates (Hannes)
- target-core ALUA cleanups + prep for v3.14 SCSI Referrals support (Hannes)
v3.14 is currently shaping to be a busy development cycle in target
land, with initial support for T10 Referrals and T10 DIF currently on
the roadmap"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits)
iscsi-target: chap auth shouldn't match username with trailing garbage
iscsi-target: fix extract_param to handle buffer length corner case
iscsi-target: Expose default_erl as TPG attribute
target_core_configfs: split up ALUA supported states
target_core_alua: Make supported states configurable
target_core_alua: Store supported ALUA states
target_core_alua: Rename ALUA_ACCESS_STATE_OPTIMIZED
target_core_alua: spellcheck
target core: rename (ex,im)plict -> (ex,im)plicit
percpu-refcount: Add percpu-refcount.o to obj-y
iscsi-target: Do not reject non-immediate CmdSNs exceeding MaxCmdSN
iscsi-target: Convert iscsi_session statistics to atomic_long_t
target: Convert se_device statistics to atomic_long_t
target: Fix delayed Task Aborted Status (TAS) handling bug
iscsi-target: Reject unsupported multi PDU text command sequence
ib_isert: Avoid duplicate iscsit_increment_maxcmdsn call
iscsi-target: Fix mutex_trylock usage in iscsit_increment_maxcmdsn
target: Core does not need blkdev.h
target: Pass through I/O topology for block backstores
iser-target: Avoid using FRMR for single dma entry requests
...
- ACPI-based device hotplug fixes for issues introduced recently and
a fix for an older error code path bug in the ACPI PCI host bridge
driver.
- Fix for recently broken OMAP cpufreq build from Viresh Kumar.
- Fix for a recent hibernation regression related to s2disk.
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar.
- System suspend error code path fix related to runtime PM and
runtime PM documentation update from Ulf Hansson.
- cpufreq's conservative governor fix from Xiaoguang Chen.
- New processor IDs for intel_idle and turbostat and removal of
an obsolete Kconfig option from Len Brown.
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg.
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu.
- Rework of the ACPI companion representation in struct device and
code cleanup related to that change from Rafael J Wysocki,
Lan Tianyu and Jarkko Nikula.
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices
from Jarkko Nikula.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABCAAGBQJSjLYNAAoJEILEb/54YlRxkEQP/1pmFWNwSsxLtTHd+PEs0Xbo
QccqvjQrnw/c8GcmK4eZrz6/xyuepmmjy9kfRKj2ENZniy0NEsSFqkTdSO3vYlva
8HKWUj7MV3evhFERXAF6Tu0b4Enx4jOP7VMtmYxJo3qrSnKRUcUzc6DGv/ACsUT1
Nkj0Lhdsg053Z+YzIXrl50w0tCDEMhVmWlMHBtYgr+dMNVnkfPBGkqMblMkKCXT2
w/yHvauZlxQHtI+8bVqTuGgNN0CPzdlpFGiuUF+5mDf6dRX8zlSn56Ia+Wyw1k9X
dQp4jYQOgPRo03rNKqQPDiPxUdc7T0RAHRvDB51Ncweuh5PfZGguQe71p6/LKY2W
i6zblZ0f/vc13hTiMrP+qzKcwZvgPB5DH7SfnHr61JKV7GNFCdYAqoceS5hYMzR9
d2Fd+txgm763IHWewXfDS/G2cU492R5qr4jpmUIACBQKWDZcqmSRDwRj83t56Ltb
jgFBMbg4vZxG7IARhind74xsALxdhsgmFjPmx+0qPWjYxcU8otQZpXbgGNI9iOuW
pxIQv5WPQW0tTmwO4HSuVCOwDPLPz5R0jkev7SvSj3Ek3TeD7He4LmnK055CATiC
puq+6dp1FISPOPJYk+0DI61qN/CB/qNwRp8LU3ctZwudPVhznIE9FFQ3iN1FdBg2
X8VDcT9t7VvVuxSBjgkj
=QMp+
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
- ACPI-based device hotplug fixes for issues introduced recently and a
fix for an older error code path bug in the ACPI PCI host bridge
driver
- Fix for recently broken OMAP cpufreq build from Viresh Kumar
- Fix for a recent hibernation regression related to s2disk
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar
- System suspend error code path fix related to runtime PM and runtime
PM documentation update from Ulf Hansson
- cpufreq's conservative governor fix from Xiaoguang Chen
- New processor IDs for intel_idle and turbostat and removal of an
obsolete Kconfig option from Len Brown
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu
- Rework of the ACPI companion representation in struct device and code
cleanup related to that change from Rafael J Wysocki, Lan Tianyu and
Jarkko Nikula
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices from
Jarkko Nikula
* tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration
ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed()
ACPI / PCI root: Clear driver_data before failing enumeration
ACPI / hotplug: Fix PCI host bridge hot removal
ACPI / hotplug: Fix acpi_bus_get_device() return value check
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
ACPI / video: clean up DMI table for initial black screen problem
ACPI / EC: Ensure lock is acquired before accessing ec struct members
PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps()
ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac
spi: Use stable dev_name for ACPI enumerated SPI slaves
i2c: Use stable dev_name for ACPI enumerated I2C slaves
ACPI: Provide acpi_dev_name accessor for struct acpi_device device name
ACPI / bind: Use (put|get)_device() on ACPI device objects too
ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro
ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
PM / Runtime: Fix error path for prepare
PM / Runtime: Update documentation around probe|remove|suspend
cpufreq: conservative: set requested_freq to policy max when it is over policy max
...
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since DEVICE_ACPI_HANDLE() is now literally identical to
ACPI_HANDLE(), replace it with the latter everywhere and drop its
definition from include/acpi.h.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
Pull vfs updates from Al Viro:
"All kinds of stuff this time around; some more notable parts:
- RCU'd vfsmounts handling
- new primitives for coredump handling
- files_lock is gone
- Bruce's delegations handling series
- exportfs fixes
plus misc stuff all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (101 commits)
ecryptfs: ->f_op is never NULL
locks: break delegations on any attribute modification
locks: break delegations on link
locks: break delegations on rename
locks: helper functions for delegation breaking
locks: break delegations on unlink
namei: minor vfs_unlink cleanup
locks: implement delegations
locks: introduce new FL_DELEG lock flag
vfs: take i_mutex on renamed file
vfs: rename I_MUTEX_QUOTA now that it's not used for quotas
vfs: don't use PARENT/CHILD lock classes for non-directories
vfs: pull ext4's double-i_mutex-locking into common code
exportfs: fix quadratic behavior in filehandle lookup
exportfs: better variable name
exportfs: move most of reconnect_path to helper function
exportfs: eliminate unused "noprogress" counter
exportfs: stop retrying once we race with rename/remove
exportfs: clear DISCONNECTED on all parents sooner
exportfs: more detailed comment for path_reconnect
...
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
Most of this branch consists of updates, additions and general churn of
the device tree source files in the kernel (arch/arm/boot/dts). Besides
that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board files
for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as well
- Some updates to pinctrl and other subsystems. Most of these are for
DT-enablement of the various platforms and acks have been collected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nH67
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
New and updated SoC support. Among the things new for this release are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as ARCH_BCM,
and turned out to be too broad a name. New name is ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the platform code
more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is more work
on consolidation instead of introduction of new non-multiplatform SoCs, we're
all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSgBrRAAoJEIwa5zzehBx3v+QP/1Z4DOzOckU7sb/IZZMXxVcS
C9G68x1n2lwqQwmMrjDAnFm+qKGDlb2SzHnUNiVy4niaGXdGSDtVzSEzK01LhUuz
BchWRy5Vb+pq0/bVLxtkqUPf0LEH/1as0uQVJNxwmV+SS9OvH+NpJHo2X6motYtX
W0l/NHwD/NYxwkjZTHUgZW9si1a8ZaG41i/h05IOpkww7RNcmtubWmQQIbKwmadc
z2QO3NsrcUvMgnoF9fOEJU2aurIx1s+6jpG6/fD1WWejCMuf0JulyfV7egREFgty
yp8QhnSTDaOvV0Gjrpx+4ERkwpVjvESpZIJoYHXjbScZHTCzkVDBLwwpmgYB1Mrb
KOKTt6+p8RAMFm43Rkf42SW8RXMM8nifed/H5Lwimi8qQT4+PuWM4i524P0Bb0Bj
tANHU2twUbY1VFRycGwWbTwPWtwxD4B0c6xflon84IGsZC31mvcfRcGaqaMtwTH4
J6CN0Bk3Tp0BUOveo0pdTPtrgOWm85MxWrzbjppKY7Lgl4A19iXqvSQjIt1sjJGz
5d8hH7KX26jKT24FiFp0fttOCRVVmg5Ks6sn2BTjX83w9S1pUg4yjZTU9cdbFbyN
zvi0d7YQYWOJTlSQlY5m5xqvRzeByAae4EDA6LKdh6JQsPyQEhHdxvMj7/ZURf8W
4jPMsgi+GxP8AGhpb20/
=WYJl
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Among the things new for this release
are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as
ARCH_BCM, and turned out to be too broad a name. New name is
ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the
platform code more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is
more work on consolidation instead of introduction of new
non-multiplatform SoCs, we're all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates,
etc"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
ARM: bcm_defconfig: Run "make savedefconfig"
ARM: bcm281xx: Add ARCH Timers to config
rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
ARM: vexpress: Enable platform-specific options in defconfig
ARM: vexpress: Make defconfig work again
ARM: sunxi: remove .init_time hooks
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
...
Here's the big USB driver update for 3.13-rc1.
It includes the usual xhci changes, EHCI updates to get the scheduling
of USB transactions working better, and a raft of gadget and musb
updates as well.
All of this has been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xycACgkQMUfUDdst+ymO+gCgxXdQXSU23i9ykc2CKBemdEBH
w6IAoKcokITcdN1IxxkfiMxOEld2hgZm
=3kbb
-----END PGP SIGNATURE-----
Merge tag 'usb-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver update from Greg KH:
"Here's the big USB driver update for 3.13-rc1.
It includes the usual xhci changes, EHCI updates to get the scheduling
of USB transactions working better, and a raft of gadget and musb
updates as well.
All of this has been in linux-next for a while with no reported
issues"
* tag 'usb-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (305 commits)
USB: Maintainers change for usb serial drivers
usb: usbtest: support container id descriptor test
usb: usbtest: support superspeed device capbility descriptor test
usb: usbtest: support usb2 extension descriptor test
usb: chipidea: only get vbus regulator for non-peripheral mode
USB: ehci-atmel: add usb_clk for transition to CCF
usb: cdc-wdm: ignore speed change notifications
USB: cdc-wdm: support back-to-back USB_CDC_NOTIFY_RESPONSE_AVAILABLE notifications
usbatm: Fix dynamic_debug / ratelimited atm_dbg and atm_rldbg macros
printk: pr_debug_ratelimited: check state first to reduce "callbacks suppressed" messages
usb: usbtest: support bos descriptor test for usb 3.0
USB: phy: samsung: Support multiple PHYs of same type
usb: wusbcore: change WA_SEGS_MAX to a legal value
usb: wusbcore: add a quirk for Alereon HWA device isoc behavior
usb: wusbcore: combine multiple isoc frames in a single transfer request.
usb: wusbcore: set the RPIPE wMaxPacketSize value correctly
usb: chipidea: host: more enhancement when ci->hcd is NULL
usb: ohci: remove ep93xx bus glue platform driver
usb: usbtest: fix checkpatch warning as sizeof code style
UWB: clean up attribute use by using ATTRIBUTE_GROUPS()
...
Custom VID/PID for Z3X Box device, popular tool for cellphone flashing.
Signed-off-by: Alexey E. Kramarenko <alexeyk13@yandex.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b8bdad6082.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 57ce61aad7.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 75417d9f99.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b9208c721c.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e917ba01d6.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b5c16c6a03.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 61fa8d694b.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c23bda365d.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 73b583af59.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a77a8c23e4.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 034d1527ad.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 7d26a78f62.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use platform_device_register_full() for those drivers which can, to
avoid messing directly with DMA masks. This can only be done when
the driver does not need to access the allocated musb platform device
from within its callbacks, which may be called during the musb
device probing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The correct way for a driver to specify the coherent DMA mask is
not to directly access the field in the struct device, but to use
dma_set_coherent_mask(). Only arch and bus code should access this
member directly.
Convert all direct write accesses to using the correct API.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a comment to explain why this driver doesn't call any of the DMA
API dma_set_mask() functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace the following sequence:
dma_set_mask(dev, mask);
dma_set_coherent_mask(dev, mask);
with a call to the new helper dma_set_mask_and_coherent().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace the following sequence:
dma_set_mask(dev, mask);
dma_set_coherent_mask(dev, mask);
with a call to the new helper dma_set_mask_and_coherent().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In Test 9 of usbtest module, it is used for performing chapter 9 tests N
times.
Container ID descriptor is one of the generic device-level capbility
descriptors which added in section 9.6.2.3 of USB 3.0 spec.
This patch adds to support getting Container ID descriptor test scenario
for USB 3.0.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Test 9 of usbtest module, it is used for performing chapter 9 tests N
times.
SuperSpeed USB Device Capability descriptor is one of the generic
device-level capbility descriptors which added in section 9.6.2.2 of USB
3.0 spec.
This patch adds to support getting SuperSpeed USB Device Capability
descriptor test scenario for USB 3.0.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Test 9 of usbtest module, it is used for performing chapter 9 tests N
times.
USB2.0 Extension descriptor is one of the generic device-level capbility
descriptors which added in section 9.6.2.1 of USB 3.0 spec.
This patch adds to support getting usb2.0 extension descriptor test
scenario for USB 3.0.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user chooses peripheral mode for this controller, the vbus
regulator doesn't need to get, since the host will supply the vbus,
it can save one vbus pin for other usage.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Frank Li <frank.li@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AT91 PMC (Power Management Controller) provides a USB clock used by
the different USB controllers (ehci, ohci and udc).
The atmel-ehci driver must configure the usb clock rate to 48Mhz in order
to get a fully functionnal USB host controller.
This configuration was formely done in mach-at91/clock.c, but will be
bypassed when moving to common clk framework.
This patch adds support for usb clock retrieval and configuration only if
CCF is enabled (CONFIG_COMMON_CLK).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only notification supported by the Device Management class is
Response Available. But this driver is also used as a subdriver of
other CDC classes, allowing notifications like Speed Change and
Network Connection. This results in log messages which are only
confusing to an end user:
[66255.801874] cdc_mbim 1-3:1.5: unknown notification 42 received: index 5 len 8
These drivers use cdc-wdm as a subdriver to allow access to an
embedded management protocol, and all management is expected to
use this protocol. There is therefore no need to handle any of
these optional CDC notifications. Instead we can let the cdc-wdm
driver recognize them and log a debug level message instead of an
error.
Reported-by: Rob Gardner <robmatic@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some MBIM devices send back-to-back USB_CDC_NOTIFY_RESPONSE_AVAILABLE notifications
when sending a message over multiple fragments or when there are unsolicited
messages available.
Count up the number of USB_CDC_NOTIFY_RESPONSE_AVAILABLE notifications received
and decrement the count and submit the urb for the next response each time userspace
completes a read the response.
Signed-off-by: Greg Suarez <gsuarez@smithmicro.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix atm_dbg to use normal pr_debug not dynamic_pr_debug
because dynamic_pr_debug may not be compiled in at all.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Test 9 of usbtest module, it is used for performing chapter 9 tests N
times. This patch adds to support getting bos descriptor test scenario for
USB 3.0.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes limitation when only one PHY of specific type
could be used.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
change WA_SEGS_MAX to a number that is legal according to the WUSB
spec.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a quirk for Alereon HWA devices to concatenate the frames of isoc
transfer requests.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Combine multiple isoc frames in a single transfer request. This allows
the HWA to take advantage of bursting to deliver data to endpoints
whose logical service interval is less than the minimum wireless USB
service interval of 4ms. Wireless audio quality is much improved after
this update.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For isochronous endpoints, set the RPIPE wMaxPacketSize value using
wOverTheAirPacketSize from the endpoint companion descriptor instead of
wMaxPacketSize from the normal endpoint descriptor.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like http://marc.info/?l=linux-usb&m=138200449428874&w=2 said:
two more things are needed to be done:
- If host_start fails, the host_stop should not be called, so we
add check that ci->hcd is not NULL.
- if the host_start fails at the beginning, we need to consider
regulator mismatch issue.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert ep93xx to use the OHCI platform driver and remove the
ohci-ep93xx bus glue driver.
Enable CONFIG_OHCI_HCD_PLATFORM in the ep93xx_defconfig so that USB
is still enabled by default on the EP93xx platform.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix commit b27c08c953 where dev_set_name()
is used without a string literal as format.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJSZRSSAAoJEIaOsuA1yqRE6EAP/AuF0dWV3wNSuv5h3ZPOybu8
uULX0E/VA2aGs8/55FeuQIJAn499zdt0KH5l8P3CGrKBPk8BN/rD55a6uwYEfWO8
wwTJpVeRyRQS8jes22vPqA22TXgl88SJO0RrsCarrzOcMNloVtOA4zyorITuGZQB
jEKmf9BdjIUlzZkH9t33v3O8kB5pJ1YvBQGRWXbBZvxSzohPC2LYerZKMPN99hDB
2YnJXVKZqZzKbcQQmJklWqRo0RTprWz0Mqcu2r8Lnnn2ZqnT3RBmCBsYXefsp4nF
egRJy51DiypEYt3/OEBf21BySjZHjO6+9jfzOmuOGoEiqw6XCRFMydVpqJJHC8WX
MoCs31VnGwwwBpSOz9ECS9QYXne9jx/bJ6iKoS736sgA20ZA6wBbEDhJlTckcZtm
TEC+UTKevNACAP8cjhGEquqwt5H/rMaYFMXEYQj+gvO2jDsNUGWb74l5VDaBiIm7
GzdUmgmYym8HKT80tgEcgvsUoUphDeNE84OW/jo1nFUDvCniLfQBAYZooEnTHY2H
AW+DqimJzNnKcHo4w/HUQhRgK9147aRbskmVIbepIIW7WQdFQBOPVy7BbfnVD2vA
j01JPshgtnjb+MZb6VqnbcaWKPnJr3KTnOpTTMyk5pKnBOf6PHb1S1Tq5uqtW2Ki
gqi/SXZJ1bYDVaaspNWr
=LDY7
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.13
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
cbaf_probe() does cbaf->usb_dev = usb_get_dev(interface_to_usbdev(iface)),
but there is no usb_put_dev() anywhere in cbaf.
The patch adds usb_put_dev() to cbaf_disconnect() and to an error path in cbaf_probe().
Also it adds missed usb_put_intf(iface) to the error path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hcd-pci.c in usbcore contains a check for wakeup requests racing with
controller suspend. This check is going to be moved out of usbcore
and into the individual controller drivers, where it can apply to all
platforms, not just PCI.
This patch adds the check to uhci-hcd. Ironically, none of the
non-PCI platform drivers for uhci-hcd implement suspend/resume.
Nevertheless, this change is needed to accomodate the upcoming change
to usbcore.
The patch also removes an outdated check of the root hub state. For
one thing, the PM layer has long been quite reliable about suspending
root hubs before controllers. For another, virtually the same check
is also made in hcd-pci.c; there's no point in repeating it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hcd-pci.c in usbcore contains a check for wakeup requests racing with
controller suspend. This check is going to be moved out of usbcore
and into the individual controller drivers, where it can apply to all
platforms, not just PCI.
This patch adds the check to ehci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes a dev_warn() call in usbcore to dev_dbg(). It's
not necessary to warn about drivers missing a reset-resume callback,
since the reset-resume method is optional.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an endian-related error in ohci-hcd (detected by
sparse) and clarifies a comment explaining a peculiar locking
arrangement that sparse warns about.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes several sparse errors in ehci-hcd introduced by
commit 3d091a6f70 (USB: EHCI: AMD periodic frame list table quirk).
Although the problem fixed by that commit affects only little-endian
systems, the source code has to use types appropriate for big-endian
too.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a type mismatch in ehci-hcd caused by commit
b35c5009bb (USB: EHCI: create per-TT bandwidth tables). The c_maskp
parameter in check_intr_schedule() was changed to point to unsigned
int rather than __hc32, but the prototype declaration wasn't adjusted
accordingly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's my pull request for usb-next and 3.13. My xHCI tree is closed
after this point, since I won't be able to run my full tests while I'm in
Scotland. After Kernel Summit, I'll be on vacation with access to email
from Oct 26th to Nov 6th.
Here's what's in this request:
- Patches to fix USB 2.0 Link PM issues that cause USB 3.0 devices to not
enumerate or misbehave when plugged into a USB 2.0 port. Those are
marked for stable.
- A msec vs jiffies bug fix by xiao jin, which results in fairly harmless
behavior, and thus isn't marked for stable.
- Xenia's patches to refactor the xHCI command handling code, which makes
it much more readable and consistent.
- Misc cleanup patches, one by Sachin Kamat and three from Dan Williams.
Here's what's not in this request:
- Dan's two patches to allow the xHCI host to use the "Windows" or "new"
enumeration scheme. I did not have time to test those, and I want to
run them with as many USB devices as I can get a hold of. That will
have to wait for 3.14.
- Xenia's patches to remove xhci_readl in favor of readl. I'll queue
those for 3.14 after I test them.
- The xHCI streams update, UAS fixes, and usbfs streams support. I'm not
comfortable with changes and fixes to that patchset coming in this late.
I would rather wait for 3.14 and be really sure the streams support is
stable before we add new userspace API and remove CONFIG_BROKEN from the
uas driver.
- Julius' patch to clear the port reset bit on hub resume that came in
a couple days ago. It looks harmless, but I would rather take the time
to test and queue it for usb-linus and the stable trees once 3.13-rc1
is out.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=H4xp
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2013-10-17' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Final patches for 3.13
Hi Greg,
Here's my pull request for usb-next and 3.13. My xHCI tree is closed
after this point, since I won't be able to run my full tests while I'm in
Scotland. After Kernel Summit, I'll be on vacation with access to email
from Oct 26th to Nov 6th.
Here's what's in this request:
- Patches to fix USB 2.0 Link PM issues that cause USB 3.0 devices to not
enumerate or misbehave when plugged into a USB 2.0 port. Those are
marked for stable.
- A msec vs jiffies bug fix by xiao jin, which results in fairly harmless
behavior, and thus isn't marked for stable.
- Xenia's patches to refactor the xHCI command handling code, which makes
it much more readable and consistent.
- Misc cleanup patches, one by Sachin Kamat and three from Dan Williams.
Here's what's not in this request:
- Dan's two patches to allow the xHCI host to use the "Windows" or "new"
enumeration scheme. I did not have time to test those, and I want to
run them with as many USB devices as I can get a hold of. That will
have to wait for 3.14.
- Xenia's patches to remove xhci_readl in favor of readl. I'll queue
those for 3.14 after I test them.
- The xHCI streams update, UAS fixes, and usbfs streams support. I'm not
comfortable with changes and fixes to that patchset coming in this late.
I would rather wait for 3.14 and be really sure the streams support is
stable before we add new userspace API and remove CONFIG_BROKEN from the
uas driver.
- Julius' patch to clear the port reset bit on hub resume that came in
a couple days ago. It looks harmless, but I would rather take the time
to test and queue it for usb-linus and the stable trees once 3.13-rc1
is out.
Sarah Sharp
Do not overwrite the multi-byte fields of usb_wa_descriptor with their
cpu format values after reading the descriptor. Leave the values as
__le16 and swap on use. This is more consistent with other uses of USB
descriptors.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch serializes access to the HWA data transfer out (DTO)
endpoint. This prevents a situation where two transfer requests being
sent concurrently to separate downstream endpoints could interleave
their transfer request and transfer data packets causing data
corruption. The transfer processing code will now attempt to acquire
the DTO resource before sending a transfer to the HWA. If it cannot
acquire the resource, the RPIPE that the transfer is assigned to will
be placed on a waiting list. When the DTO resource is released, the
actor releasing the resource will serivce the RPIPEs that are waiting.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If everything (musb, cppi41, phy) is built-in then musb will start
without the dma engine printing only
|musb-hdrc musb-hdrc.0.auto: Falied to request rx1.
The reason for this is that the musb device structs are created & probed
before those of the cppi41 device. So the cppi41 device is probed too
late.
As a workaround for this allow the musb_cppi41 part to defer the probe
if everything is fine except for the missing DMA controller. In case of
another error we continue.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In commit f3ce4d5 ("usb: musb: core: call dma_controller_destroy() in the err path")
I erroneously assumed that the dma controller is not removed in the
error patch. This was wrong because it happens later via musb_free().
That means the original commit can be reverted because it is wrong or we
do this, so it is more obvious.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The patch fixes two issues in the error path cleanup:
- in MUSB_PORT_MODE_DUAL_ROLE mode, if musb_gadget_setup() fails we
never cleanup the host struct earlier allocated.
- if musb_init_debugfs() or sysfs_create_group() fails, then we never
free the host part initialization, only device part.
Cc: stable@vger.kernel.org # v3.11
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix spacing, improve error code returned, remove unused #define,
use strtobool() instead of kstrtou8().
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
I introduced this check here because it looked wrong in HOST only
configurions. The timer would remove that session bit and will never
come back and so there would not be another session.
Now that I played with OTG for a while I belive this workaround is
only required for the OTG mode because we have to end the session and
then we have to try to start manually.
Therefore, this patch limits this timer to the OTG only port mode so we
don't need to poll around in device only mode.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the comments, we rely on the OTG timer because the core
does not expose some important OTG details. So far this is all I
know. After playing with OTG I stumbled over a problem:
musb is recognized as a B-device without a problem. Whenever a cable is
plugged, the VBUS rises, musb recognizes this as a starting session,
sets the MUSB_DEVCTL_SESSION bit by itself and a RESET interrupt occurs,
the session starts. Good.
After a disconnect, the timer is started and re-starts itself because
it remains in B_IDLE with the BDEVICE set. I didn't figure the the
reason or the need for it. Nothing changes here except for OTG state
from B to A device if the BDEVICE bit disappears. This doesn't make much
sense to me because nothing happens after this. _IF_ we receive an
interrupt before the state change then we may act on wrong condition.
Plugging a B-device (and letting MUSB act as host) doesn't work here.
The reason seems to be that the MUSB tries to start a session, it fails
and then it removes the bit. So we never start as a host.
This patch sets the MUSB_DEVCTL_SESSION bit in the IDLE state so musb
can try to establish a session as host. After the bit is set, musb tries
to start a session and if it fails it clears the bit. Therefore it will
try over and over again until a session either as host or as device is
established.
The readout of the MUSB_DEVCTL register after the removal the
MUSB_DEVCTL_SESSION (in A_WAIT_BCON) has been removed because it did not
contain the BDEVICE bit set (in the second read) leading to A_IDLE. After
plugging a host musb assumed that it is also a host and complained about
a missing reset. However a third read of the register has has the BDEVICE
bit set so it seems that it is not stable.
This mostly what da8xx.c is doing except that we set the timer also
after A_WAIT_BCON so the session bit can be triggered.
Whit this change I was able to keep am335x-evm in OTG mode and plug in
either a HOST or a DEVICE and in a random order and the device was
recognized.
Cc: stable@vger.kernel.org # v3.11
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves dsps_musb_try_idle() before dsps_musb_enable() so the
declaration (of dsps_musb_try_idle() can be removed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The timer is initialized right after musb is probed. There is actually
no need to have this timer running because _nothing_ will happen until
we have the gadget loaded. Also we need this timer only if we run in OTG
mode _and_ we need it also after the gadget has been replaced with
another one.
I've been looking at am35x.c, da8xx.c, omap2430.c, tusb6010.c. da8xx
seem to have the same problem as dsps and doing mostly the same thing.
tusb6010 seem to do something different and do some actual "idle / power
saving" work so I am not too comfortable to remove
musb_platform_try_idle() from musb_gadget_setup().
Therefore this patch does not start the timer if there is no gadget
active (which is at musb_gadget_setup() at time). In order to have the
timer active after the gadget is loaded it will be triggered from
dsps_musb_enable().
Cc: stable@vger.kernel.org # v3.11
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In commit 001dd84 ("usb: musb: start musb on the udc side, too") it was
ensured that the state engine is started also in OTG mode after a
removal / insertion of the gadget.
Unfortunately this change also introduced a bug: If the device is
configured as OTG and it connected with a remote host _without_ loading
a gadget then we bug() later (because musb->otg->gadget is not
initialized).
Initially I assumed it might be nice to have the host part of musb in
OTG mode working without having a gadget loaded. This bug and fact that
it wasn't working like this before the host/gadget split made me realize
that this was a silly idea.
This patch now introduces back the old behavior where in OTG mode the
host mode is only working after the gadget has been loaded.
Cc: stable@vger.kernel.org # v3.11
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Only used for debug output, so we don't need to save it.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Perform an unconditional toggle of the cycle bit with 'xor'.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Remove a few extra lines and make it clear that all implementations
disable the port by sharing the same line of code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The USB3503 driver had an incorrect depedency on REGMAP, instead of
REGMAP_I2C. This caused the build to fail since the necessary regmap
i2c pieces were not available.
Signed-off-by: Matthew Dawson <matthew@mjdsystems.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CMA fails to initialize in v3.12-rc4, the chipidea driver oopses
the kernel while trying to remove and put the HCD which doesn't exist:
WARNING: CPU: 0 PID: 6 at /home/rmk/git/linux-rmk/arch/arm/mm/dma-mapping.c:511
__dma_alloc+0x200/0x240()
coherent pool not initialised!
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56
Workqueue: deferwq deferred_probe_work_func
Backtrace:
[<c001218c>] (dump_backtrace+0x0/0x10c) from [<c0012328>] (show_stack+0x18/0x1c)
r6:c05fd9cc r5:000001ff r4:00000000 r3:df86ad00
[<c0012310>] (show_stack+0x0/0x1c) from [<c05f3a4c>] (dump_stack+0x70/0x8c)
[<c05f39dc>] (dump_stack+0x0/0x8c) from [<c00230a8>] (warn_slowpath_common+0x6c/0x8c)
r4:df883a60 r3:df86ad00
[<c002303c>] (warn_slowpath_common+0x0/0x8c) from [<c002316c>] (warn_slowpath_fmt+0x38/0x40)
r8:ffffffff r7:00001000 r6:c083b808 r5:00000000 r4:df2efe80
[<c0023134>] (warn_slowpath_fmt+0x0/0x40) from [<c00196bc>] (__dma_alloc+0x200/0x240)
r3:00000000 r2:c05fda00
[<c00194bc>] (__dma_alloc+0x0/0x240) from [<c001982c>] (arm_dma_alloc+0x88/0xa0)
[<c00197a4>] (arm_dma_alloc+0x0/0xa0) from [<c03e2904>] (ehci_setup+0x1f4/0x438)
[<c03e2710>] (ehci_setup+0x0/0x438) from [<c03cbd60>] (usb_add_hcd+0x18c/0x664)
[<c03cbbd4>] (usb_add_hcd+0x0/0x664) from [<c03e89f4>] (host_start+0xf0/0x180)
[<c03e8904>] (host_start+0x0/0x180) from [<c03e7c34>] (ci_hdrc_probe+0x360/0x670
)
r6:df2ef410 r5:00000000 r4:df2c3010 r3:c03e8904
[<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24)
[<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234)
...
---[ end trace c88ccaf3969e8422 ]---
Unable to handle kernel NULL pointer dereference at virtual address 00000028
pgd = c0004000
[00000028] *pgd=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56
Workqueue: deferwq deferred_probe_work_func
task: df86ad00 ti: df882000 task.ti: df882000
PC is at usb_remove_hcd+0x10/0x150
LR is at host_stop+0x1c/0x3c
pc : [<c03cacec>] lr : [<c03e88e4>] psr: 60000013
sp : df883b50 ip : df883b78 fp : df883b74
r10: c11f4c54 r9 : c0836450 r8 : df30c400
r7 : fffffff4 r6 : df2ef410 r5 : 00000000 r4 : df2c3010
r3 : 00000000 r2 : 00000000 r1 : df86b0a0 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7d Table: 2f29404a DAC: 00000015
Process kworker/u2:0 (pid: 6, stack limit = 0xdf882240)
Stack: (0xdf883b50 to 0xdf884000)
...
Backtrace:
[<c03cacdc>] (usb_remove_hcd+0x0/0x150) from [<c03e88e4>] (host_stop+0x1c/0x3c)
r6:df2ef410 r5:00000000 r4:df2c3010
[<c03e88c8>] (host_stop+0x0/0x3c) from [<c03e8aa0>] (ci_hdrc_host_destroy+0x1c/0x20)
r5:00000000 r4:df2c3010
[<c03e8a84>] (ci_hdrc_host_destroy+0x0/0x20) from [<c03e7c80>] (ci_hdrc_probe+0x3ac/0x670)
[<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24)
[<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234)
[<c030fc10>] (driver_probe_device+0x0/0x234) from [<c030ff28>] (__device_attach+0x44/0x48)
...
---[ end trace c88ccaf3969e8423 ]---
Fix this so at least we can continue booting and get to a shell prompt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the Port Reset Change flag to the set of bits that are
preemptively cleared on init/resume of a hub. In theory this bit should
never be set unexpectedly... in practice it can still happen if BIOS,
SMM or ACPI code plays around with USB devices without cleaning up
correctly. This is especially dangerous for XHCI root hubs, which don't
generate any more Port Status Change Events until all change bits are
cleared, so this is a good precaution to have (similar to how it's
already done for the Warm Port Reset Change flag).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove a lingering macro that just hid a dereference.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Some USB drive enclosures do not correctly report an
overflow condition if they hold a drive with a capacity
over 2TB and are confronted with a READ_CAPACITY_10.
They answer with their capacity modulo 2TB.
The generic layer cannot cope with that. It must be told
to use READ_CAPACITY_16 from the beginning.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface 6 of this device speaks QMI as per tests done by us.
Credits go to Antonella for providing the hardware.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Antonella Pellizzari <anto.pellizzari83@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces the 'event' argument of xhci_handle_cmd_set_deq() and
xhci_handle_cmd_reset_ep(), which is used to retrieve the command completion
status code, with the cmd_comp_code directly, since it is available.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Since the Slot ID field in the command completion event matches the Slot ID
field in the associated command TRB for the Stop Endpoint, Set Dequeue Pointer
and Reset Endpoint commands, this patch adds in the handlers of their
completion events a 'slot_id' argument and removes the slot id calculation
in each of them.
Also, a WARN_ON() was added in case the slot ids reported by command TRB and
event TRB differ (although according to xhci spec rev1.0 that should not happen)
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch replaces 'xhci->cmd_ring->dequeue' with 'trb', the address of
the command TRB, since it is available to reduce line length.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch adds a new variable 'cmd_type' to hold the command type so that
switch cases can be simplified by removing TRB_TYPE() macro improving
code readability.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch adds a new variable 'cmd_trb' to hold the address of the
command TRB, that is associated with the command completion event,
and to replace repetitions of xhci->cmd_ring->dequeue into the code.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch adds a new variable 'cmd_comp_code' to hold the command completion
status code aiming to reduce code duplication and to improve code readability.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The function that handles xHCI command completion is much too long and
there is need to be broken up into individual functions for each command
completion to improve code readablity.
This patch refactors the code in TRB_CONFIG_EP switch case, in
handle_cmd_completion(), into a fuction named xhci_handle_cmd_config_ep().
There were added two additional variables, 'add_flags' and 'drop_flags',
to reduce line length below 80 chars and improve code readability.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch removes the variable 'ep_ring' that is assigned in
TRB_CONFIG_EP switch case but never used.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The function that handles xHCI command completion is much too long and
there is need to be broken up into individual functions for each command
completion to improve code readablity.
This patch refactors the code in TRB_EVAL_CONTEXT switch case in
handle_cmd_completion() into a fuction named xhci_handle_cmd_eval_ctx().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The function that handles xHCI command completion is much too long and
there is need to be broken up into individual functions for each command
completion to improve code readablity.
This patch refactors the code in TRB_NEC_GET_FW switch case in
handle_cmd_completion() into a fuction named xhci_handle_cmd_nec_get_fw().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The function that handles xHCI command completion is much too long and
there is need to be broken up into individual functions for each command
completion to improve code readablity.
This patch refactors the code in TRB_RESET_DEV switch case in
handle_cmd_completion() into a fuction named xhci_handle_cmd_reset_dev().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Since the slot id retrieved from the Reset Device TRB matches the slot id in
the command completion event, which is available, there is no need to determine
it again.
This patch removes the uneccessary reassignment to slot id and adds a WARN_ON
in case the two Slot ID fields differ (although according xhci spec rev1.0
they should not differ).
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The function that handles xHCI command completion is much too long and
there is need to be broken up into individual functions for each command
completion to improve code readablity.
This patch refactors the code in TRB_ADDR_DEV switch case in
handle_cmd_completion() into a fuction named xhci_handle_cmd_addr_dev().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The function that handles xHCI command completion is much too long and
there is need to be broken up into individual functions for each command
completion to improve code readablity.
This patch refactors the code in TRB_DISABLE_SLOT switch case in
handle_cmd_completion() into a fuction named xhci_handle_cmd_disable_slot().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The function that handles xHCI command completion is much too long and
there is need to be broken up into individual functions for each command
completion to improve code readablity.
This patch refactors the code in TRB_ENABLE_SLOT switch case in
handle_cmd_completion() into a fuction named xhci_handle_cmd_enable_slot().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch renames the function handlers of a triggered Command Completion
Event that correspond to each command type into 'xhci_handle_cmd_<type>'.
That is done to give a consistent naming space to all the functions that
handle Command Completion Events and that will permit the code reader to
reference to them more easily.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch removes the "adjective" argument from xhci_giveback_urb_in_irq(),
since it is not used in the function anymore.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The usage of USB_CTRL_SET_TIMEOUT in xhci is incorrect.
The definition of USB_CTRL_SET_TIMEOUT is 5000ms. The
input timeout to wait_for_completion_interruptible_timeout
is jiffies. That makes the timeout be longer than what
we want, such as 50s in some platform.
The patch is to use XHCI_CMD_DEFAULT_TIMEOUT instead of
USB_CTRL_SET_TIMEOUT as command completion event timeout.
Signed-off-by: xiao jin <jin.xiao@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
'xhci_del_comp_mod_timer' is local to this file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The USB core currently handles enabling and disabling optional USB power
management features during device transitions (device suspend/resume,
driver bind/unbind, device reset, and device disconnect). Those
optional power features include Latency Tolerance Messaging (LTM),
USB 3.0 Link PM, and USB 2.0 Link PM.
The USB core currently enables LPM on device enumeration and disables
USB 2.0 Link PM when the device is reset. However, the xHCI driver
disables LPM when the device is disconnected and the device context is
freed. Push the call up into the USB core, in order to be consistent
with the core handling all power management enabling and disabling.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Some usb3 devices falsely claim they support usb2 hardware Link PM
when connected to a usb2 port. We only trust hardwired devices
or devices with the later BESL LPM support to be LPM enabled as default.
[Note: Sarah re-worked the original patch to move the code into the USB
core, and updated it to check whether the USB device supports BESL,
instead of checking if the xHCI port it's connected to supports BESL
encoding.]
This patch should be backported to kernels as old as 3.11, that
contain the commit a558ccdcc7 "usb: xhci:
add USB2 Link power management BESL support". Without this fix, some
USB 3.0 devices will not enumerate or work properly under USB 2.0 ports
on Haswell-ULT systems.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
How it's supposed to work:
--------------------------
USB 2.0 Link PM is a lower power state that some newer USB 2.0 devices
support. USB 3.0 devices certified by the USB-IF are required to
support it if they are plugged into a USB 2.0 only port, or a USB 2.0
cable is used. USB 2.0 Link PM requires both a USB device and a host
controller that supports USB 2.0 hardware-enabled LPM.
USB 2.0 Link PM is designed to be enabled once by software, and the host
hardware handles transitions to the L1 state automatically. The premise
of USB 2.0 Link PM is to be able to put the device into a lower power
link state when the bus is idle or the device NAKs USB IN transfers for
a specified amount of time.
...but hardware is broken:
--------------------------
It turns out many USB 3.0 devices claim to support USB 2.0 Link PM (by
setting the LPM bit in their USB 2.0 BOS descriptor), but they don't
actually implement it correctly. This manifests as the USB device
refusing to respond to transfers when it is plugged into a USB 2.0 only
port under the Haswell-ULT/Lynx Point LP xHCI host.
These devices pass the xHCI driver's simple test to enable USB 2.0 Link
PM, wait for the port to enter L1, and then bring it back into L0. They
only start to break when L1 entry is interleaved with transfers.
Some devices then fail to respond to the next control transfer (usually
a Set Configuration). This results in devices never enumerating.
Other mass storage devices (such as a later model Western Digital My
Passport USB 3.0 hard drive) respond fine to going into L1 between
control transfers. They ACK the entry, come out of L1 when the host
needs to send a control transfer, and respond properly to those control
transfers. However, when the first READ10 SCSI command is sent, the
device NAKs the data phase while it's reading from the spinning disk.
Eventually, the host requests to put the link into L1, and the device
ACKs that request. Then it never responds to the data phase of the
READ10 command. This results in not being able to read from the drive.
Some mass storage devices (like the Corsair Survivor USB 3.0 flash
drive) are well behaved. They ACK the entry into L1 during control
transfers, and when SCSI commands start coming in, they NAK the requests
to go into L1, because they need to be at full power.
Not all USB 3.0 devices advertise USB 2.0 link PM support. My Point
Grey USB 3.0 webcam advertises itself as a USB 2.1 device, but doesn't
have a USB 2.0 BOS descriptor, so we don't enable USB 2.0 Link PM. I
suspect that means the device isn't certified.
What do we do about it?
-----------------------
There's really no good way for the kernel to test these devices.
Therefore, the kernel needs to disable USB 2.0 Link PM by default, and
distros will have to enable it by writing 1 to the sysfs file
/sys/bus/usb/devices/../power/usb2_hardware_lpm. Rip out the xHCI Link
PM test, since it's not sufficient to detect these buggy devices, and
don't automatically enable LPM after the device is addressed.
This patch should be backported to kernels as old as 3.11, that
contain the commit a558ccdcc7 "usb: xhci:
add USB2 Link power management BESL support". Without this fix, some
USB 3.0 devices will not enumerate or work properly under USB 2.0 ports
on Haswell-ULT systems.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
To enable USB 2.0 Link Power Management (LPM), the xHCI host controller
needs the device slot ID to generate the device address used in L1 entry
tokens. That information is set in the L1 device slot ID field of the
USB 2.0 LPM registers.
Currently, the L1 device slot ID is overwritten when the xHCI driver
initiates the software test of USB 2.0 Link PM in
xhci_usb2_software_lpm_test. It is never cleared when USB 2.0 Link PM
is disabled for the device. That should be harmless, because the
Hardware LPM Enable (HLE) bit is cleared when USB 2.0 Link PM is
disabled, so the host should not pay attention to the slot ID.
This patch should have no effect on host behavior, but since
xhci_usb2_software_lpm_test is going away in an upcoming bug fix patch,
we need to move that code to the function that enables and disables USB
2.0 Link PM.
This patch should be backported to kernels as old as 3.11, that contain
the commit a558ccdcc7 "usb: xhci: add USB2
Link power management BESL support". The upcoming bug fix patch is also
marked for that stable kernel.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Before the USB core resets a device, we need to disable the L1 timeout
for the roothub, if USB 2.0 Link PM is enabled. Otherwise the port may
transition into L1 in between descriptor fetches, before we know if the
USB device descriptors changed. LPM will be re-enabled after the
full device descriptors are fetched, and we can confirm the device still
supports USB 2.0 LPM after the reset.
We don't need to wait for the USB device to exit L1 before resetting the
device, since the xHCI roothub port diagrams show a transition to the
Reset state from any of the Ux states (see Figure 34 in the 2012-08-14
xHCI specification update).
This patch should be backported to kernels as old as 3.2, that contain
the commit 65580b4321 "xHCI: set USB2
hardware LPM". That was the first commit to enable USB 2.0
hardware-driven Link Power Management.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The device descriptors are messed up after remote wakeup
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Value of can_write variable in s3c_hsotg_write_fifo function should be limited
to 512 only for non-periodic endpoints. There was some discrepancy between
comment and code, becouse comment suggests correct behavior, but in the code
limit was applied to periodic endpoints too. So there is additional check
causing the limitation concerns only non-periodic endpoints.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In dedicated-fifo mode TxFIFOEmpty interrupt should be asserted when TxFIFO
for this endpoint is completly empty, so NPTxFEmpLvl and PTxFEmpLvl bits are
set in GAHBCFG register.
In DIEPMSK register INTknTXFEmpMsk is set, becouse it's needed to indicate
FIFO Empty state.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
All requests for endpoint are completed when it was halted and the halt was
cleared by CLEAR_FEATURE, but not when new state is same as previous.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Property "halted" of s3c_hsotg_ep structure is actually initialised when ep
enabled, and changed when halt is set/cleared.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In OEPInt/IEPInt interrupts handling added bitwise and of DAINT and
DAINTMSK, because we should handle masked interrupts only.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When s3c_hsotg_trytx is called for ep without enqueued request, interrupts
for this ep are disabled, to prevent interrupt flooding. Interrupts are
enabled when new request for this ep is starting.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In s3c_hsotg_write_fifo function PTxFEmp/NPTxFEmp interrupts are enabled
only in shared-fifo mode. In dedicated-fifo mode they should not be used
(when enabled then cause interrupt storm).
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After normal handling of SetupDone interrupt, XferCompl interrupt occurs, and
then we enqueue new setup request. But when ep0 is stalled, there is no
XferCompl, so we have to enqueue setup request immediately after stalling ep.
Otherwise incoming control requests won't be processed correctly.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If cdrom flag is set ro flag is implied. Try setting the ro first, and
only if it succeeds set the cdrom flag.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
strtobool is more flexible for the user and is more appropriate in the
context.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- Always build in board-generic, and add pdata quirks and auxdata
support for it so we have all the pdata related quirks
in the same place.
- Merge of the drivers/pinctrl changes that are needed for PM
to continue working on omap3 and also needed for other omaps
eventually. The three pinctrl related patches have been acked
by Linus Walleij and are pulled into both the pinctrl tree
and this branch.
- Few defconfig related changes for drivers needed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=bqsS
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Changes needed to prepare for making omap3 device tree only:
- Always build in board-generic, and add pdata quirks and auxdata
support for it so we have all the pdata related quirks
in the same place.
- Merge of the drivers/pinctrl changes that are needed for PM
to continue working on omap3 and also needed for other omaps
eventually. The three pinctrl related patches have been acked
by Linus Walleij and are pulled into both the pinctrl tree
and this branch.
- Few defconfig related changes for drivers needed.
* tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (523 commits)
ARM: configs: omap2plus_defconfig: enable dwc3 and dependencies
ARM: OMAP2+: Add WLAN modules and of_serial to omap2plus_defconfig
ARM: OMAP2+: Run make savedefconfig on omap2plus_defconfig to shrink it
ARM: OMAP2+: Add minimal 8250 support for GPMC
ARM: OMAP2+: Use pdata quirks for wl12xx for omap3 evm and zoom3
ARM: OMAP: Move DT wake-up event handling over to use pinctrl-single-omap
ARM: OMAP2+: Add support for auxdata
pinctrl: single: Add support for auxdata
pinctrl: single: Add support for wake-up interrupts
pinctrl: single: Prepare for supporting SoC specific features
ARM: OMAP2+: igep0020: use display init from dss-common
ARM: OMAP2+: pdata-quirks: add legacy display init for IGEPv2 board
+Linux 3.12-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This reverts commit 9b0a1de3c8.
Aaro writes:
With v3.12-rc4 I can no longer connect to N800 (OMAP2) with USB
(peripheral, g_ether).
According to git bisect this is caused by:
9b0a1de3c8 is the first bad commit
So revert this patch, as Felipe says:
It's unfortunate that tusb6010 is so messed up
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device is not responsive when resumed, unless it is reset.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The non-DT for EXYNOS SoCs is not supported from v3.11.
Thus, there is no need to support non-DT for Exynos OHCI driver.
The 'include/linux/platform_data/usb-ohci-exynos.h' file has been
used for non-DT support. Thus, the 'usb-ohci-exynos.h' file can
be removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the use of local_irq_save() and IRQF_DISABLED, no longer needed since
interrupt handlers are always run with interrupts disabled on the
current CPU.
Tested successfully with 3.12.0-rc4 on my PC. Didn't find
any issue because of this change.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the initial delay before the startup of a newly
scheduled isochronous stream. Currently the stream doesn't start
for at least 5 ms (40 microframes). This value is just an estimate;
it has no real justification.
Instead, we can start the stream as soon as possible after the
scheduling computations are complete. Essentially this requires
nothing more than reading the frame counter after the stream is
scheduled, instead of before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch continues the scheduling changes in ehci-hcd by adding a
table to store the bandwidth allocation below each TT. This will
speed up the scheduling code, as it will no longer need to read
through the entire schedule to compute the bandwidth currently in use.
Properly speaking, the FS/LS budget calculations should be done in
terms of full-speed bytes per microframe, as described in the USB-2
spec. However the driver currently uses microseconds per microframe,
and the scheduling code isn't robust enough at this point to change
over. For the time being, we leave the calculations as they are.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 476e4bf939.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit 056ca85dab.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit 19d3394304.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit 86a63f1021.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit 018258b436.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit fea0896fd3.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit 36a8758736.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Make sure to return errors from tiocmget rather than rely on
uninitialised stack data.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export usb_serial_generic_write_start which is needed when implementing
a custom resume function while still relying on the generic write
implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add memory-flags parameter to usb_serial_generic_write_start which is
called from write, resume and completion handler, all with different
allocation requirements.
Note that by using the memory flag to determine when called from the
completion handler, everything will work as before even if the
completion handler is run with interrupts enabled (as suggested).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up some comments, drop excessive comments and fix-up style.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DECLARE_BITMAP macro should be used for declaring this bitmap.
This commit converts the busmap from a struct to a simple (static)
bitmap, using the DECLARE_BITMAP macro from linux/types.h.
Please review, as I'm new to kernel development, I don't know if this
has any hidden side effects!
Suggested by joe@perches.com
Signed-off-by: Matthias Beyer <mail@beyermatthias.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, Samsung is using 'EXYNOS' as the name of Samsung SoCs.
Thus, ehci-exynos is preferred than ehci-s5p.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The non-DT for EXYNOS SoCs is not supported from v3.11.
Thus, there is no need to support non-DT for Exynos EHCI driver.
The 'include/linux/platform_data/usb-ehci-s5p.h' file has been
used for non-DT support. Thus, the 'usb-ehci-s5p.h' file can
be removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch significantly changes the scheduling code in ehci-hcd.
Instead of calculating the current bandwidth utilization by trudging
through the schedule and adding up the times used by the existing
transfers, we will now maintain a table holding the time used for each
of 64 microframes. This will drastically speed up the bandwidth
computations.
In addition, it eliminates a theoretical bug. An isochronous endpoint
may have bandwidth reserved even at times when it has no transfers
listed in the schedule. The table will keep track of the reserved
bandwidth, whereas adding up entries in the schedule would miss it.
As a corollary, we can keep bandwidth reserved for endpoints even
when they aren't in active use. Eventually the bandwidth will be
reserved when a new alternate setting is installed; for now the
endpoint's reservation takes place when its first URB is submitted.
A drawback of this approach is that transfers with an interval larger
than 64 microframes will have to be charged for bandwidth as though
the interval was 64. In practice this shouldn't matter much;
transfers with longer intervals tend to be rather short anyway (things
like hubs or HID devices).
Another minor drawback is that we will keep track of two different
period and phase values: the actual ones and the ones used for
bandwidth allocation (which are limited to 64). This adds only a
small amount of overhead: 3 bytes for each endpoint.
The patch also adds a new debugfs file named "bandwidth" to display
the information stored in the new table.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch begins the process of unifying the scheduling parameters
that ehci-hcd uses for interrupt and isochronous transfers. It
creates an ehci_per_sched structure, which will be stored in both
ehci_qh and ehci_iso_stream structures, and will contain the common
scheduling information needed for both.
Initially we merely create the new structure and move some existing
fields into it. Later patches will add more fields and utilize these
structures in improved scheduling algorithms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci-hcd is inconsistent in the sentinel values it uses to indicate
that no frame number has been assigned for a periodic transfer. Some
places it uses NO_FRAME (defined as 65535), other places it uses -1,
and elsewhere it uses 9999.
This patch defines a value for NO_FRAME which can fit in a 16-bit
signed integer, and changes the code to use it everywhere.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci-hcd uses a value of 0 in an endpoint's toggle flag to indicate
that the endpoint has been reset (and therefore the Data Toggle bit
needs to be cleared in the endpoint's QH overlay region).
The toggle flag should be set to 0 only when ehci_endpoint_reset()
succeeds. This patch moves the usb_settoggle() call into the
appropriate branch of the "if" statement.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The scheduling code in ehci-hcd contains an error. For full-speed
isochronous-OUT transfers, the EHCI spec forbids scheduling
Start-Split transactions in H-microframe 7, but the driver allows it
anyway. This patch adds a check to prevent it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the bandwidth statistics maintained by ehci-hcd show up only
in the /sys/kernel/debug/usb/devices file, they ought to be calculated
correctly. The calculation for full-speed isochronous endpoints is
wrong; it mistakenly yields bytes per microframe instead of bytes per
frame. The "interval" value, which is in frames, should not be
converted to microframes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check_intr_schedule() routine in ehci-hcd looks at the wrong
microframes when checking to see if a full-speed or low-speed
interrupt endpoint will fit in the periodic schedule. If the
Start-Split transaction is scheduled for microframe N then the
Complete-Split transactions get scheduled for microframes N+2, N+3, and
N+4. However the code considers N+1, N+2, and N+3 instead.
This patch fixes the limits on the "for" loop and also improves the
use of whitespace.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_wait_anchor_empty_timeout() should wait till the completion handler
has run. Both the zd1211rw driver and the uas driver (in its task mgmt) depend
on the completion handler having completed when usb_wait_anchor_empty_timeout()
returns, as they read state set by the completion handler after an
usb_wait_anchor_empty_timeout() call.
But __usb_hcd_giveback_urb() calls usb_unanchor_urb before calling the
completion handler. This is necessary as the completion handler may
re-submit and re-anchor the urb. But this introduces a race where the state
these drivers want to read has not been set yet by the completion handler
(this race is easily triggered with the uas task mgmt code).
I've considered adding an anchor_count to struct urb, which would be
incremented on anchor and decremented on unanchor, and then only actually
do the anchor / unanchor on 0 -> 1 and 1 -> 0 transtions, combined with
moving the unanchor call in hcd_giveback_urb to after calling the completion
handler. But this will only work if urb's are only re-anchored to the same
anchor as they were anchored to before the completion handler ran.
And at least one driver re-anchors to another anchor from the completion
handler (rtlwifi).
So I have come up with this patch instead, which adds the ability to
suspend wakeups of usb_wait_anchor_empty_timeout() waiters to the usb_anchor
functionality, and uses this in __usb_hcd_giveback_urb() to delay wake-ups
until the completion handler has run.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When devm_usb_get_phy() fails, usb_put_hcd() should be called
to prevent memory leak.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows MSM EHCI controller to be specified via device tree.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use struct usb_hcd::phy to hold USB PHY instance.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These aren't necessary after switch and if blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the device id for the Inovia SEW858 device to the option driver.
Reported-by: Pavel Parkhomenko <ra85551@gmail.com>
Tested-by: Pavel Parkhomenko <ra85551@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this change, the USB cable for Freestyle Option and compatible
glucometers will not be detected by the driver.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceSubClass value.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's four patches for 3.12.
The first patch is a bug fix for the USB 2.0 Link PM registers that I sent
out to the list a long time ago (August), but forgot to queue up. The
second and fourth patches are quirks for xHCI hosts. These patches are
marked for stable. The third patch fixes a bug uncovered with sparse.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4Y1d
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2013-10-09' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Pull xhci USB fixes from Sarah:
xhci: Bug fixes and quirks for 3.12
Hi Greg,
Here's four patches for 3.12.
The first patch is a bug fix for the USB 2.0 Link PM registers that I sent
out to the list a long time ago (August), but forgot to queue up. The
second and fourth patches are quirks for xHCI hosts. These patches are
marked for stable. The third patch fixes a bug uncovered with sparse.
Sarah Sharp
A single patch fixing musb start when using peripheral
only configurations. It turns out that musb_start() needs
to be called for peripheral too, so that function is
factored out of musb_virthub.c and into musb_core.c since
it's shared for both roles.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=wdwW
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Pull USB gadget fixes from Felipe:
usb: musb: fix for v3.12-rc
A single patch fixing musb start when using peripheral
only configurations. It turns out that musb_start() needs
to be called for peripheral too, so that function is
factored out of musb_virthub.c and into musb_core.c since
it's shared for both roles.
Signed-of-by: Felipe Balbi <balbi@ti.com>
- Clock tree support
- Clock management support using PM core
- Keystone config update for EMDA with ack from Vinod
- Enable SPI and I2C drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=d2uA
-----END PGP SIGNATURE-----
Merge tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/soc
From Santosh Shilimkar:
SOC updates for Keystone II devices:
- Clock tree support
- Clock management support using PM core
- Keystone config update for EMDA with ack from Vinod
- Enable SPI and I2C drivers
* tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: (510 commits)
ARM: keystone: Enable I2C and SPI bus support
ARM: keystone: Select TI_EDMA to be able to enable SPI driver
dma: Allow TI_EDMA selectable for ARCH_KEYSTONE
ARM: dts: keystone: Add the SPI nodes
ARM: dts: keystone: Add i2c device nodes
ARM: keystone: add PM domain support for clock management
ARM: keystone: Enable clock drivers
ARM: dts: keystone: Add clock phandle to UART nodes
ARM: dts: keystone: Add clock tree data to devicetree
+Linux 3.12-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The callers are expecting an ERR_PTR value in case
of an error. Change he code to return with an encoded
-ENOMEM value in the case of a failed devres_alloc call.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Create a way for VERBOSE_DEBUG to be enabled during
drivers/usb/gadget/ build.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
I have am335x-evm with one port running in OTG mode. Since commit
fe4cb09 ("usb: musb: gadget: remove hcd initialization") the loaded
gadget does non pop up on the host. All I see is
|usb 4-5: new high-speed USB device number 52 using ehci-pci
|usb 4-5: device descriptor read/64, error -110
Since a later commit 2cc65fe ("usb: musb: add musb_host_setup() and
musb_host_cleanup()) the gadget shows up on the host again but only
in OTG mode (because we have the host init code running). It does not
work in device only mode.
If running in OTG mode and the gadget is removed and added back (rmmod
followed by modprobe of a gadget) then the same error is pops up on the
host side.
This patch ensures that the gadget side also executes musb_start() which
puts the chip in "connect accept" mode. With this change the device
works in OTG & device mode and the gadget can be added & removed
multiple times.
A device (if musb is in OTG mode acting as a host) is only recognized if
it is attached during module load (musb_hdrc module). After the device
unplugged and plugged again the host does not recognize it. We get a
buch of errors if musb running in OTG mode, attached to a host and no
gadget is loaded. Bah.
This is one step forward. Host & device only mode should work. I will
look at OTG later. I looked at this before commit fe4cb09 and OTG wasn't
working there perfectly so I am not sure that it is a regression :)
Cc: <stable@vger.kernel.org> # v3.11
Cc: Daniel Mack <zonque@gmail.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes unused label.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds Multi Count support. It adds few modifications:
- Fix s3c_hsotg_set_ep_maxpacket() function. Field wMaxPacketSize of endpoint
descriptor is now splitted into maximum packet size value and number of
additional transaction per microframe.
- Modify s3c_hsotg_write_fifo() function. It actually calculates transfer
size, taking into account Multi Count value, which indicates number of
transactions per microframe.
- Fix s3c_hsotg_start_req() function by setting number of packets to Multi
Count field in DIEPTSIZ register for isochronous endpoints.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds isochronous transfer support. It adds few modifications:
- Modify s3c_hsotg_epint() function. Some interrupts are ignored for
isochronous endpoints, (e.g. INTknTXFEmpMsk) becouse isochronous request is
always transfered in single transaction, which ends with XferCompl interrupt.
- Add Odd/Even microframe toggle to allow data transfering in each microframe
in s3c_hsotg_epint() function.
- Fix s3c_hsotg_ep_enable() function by supporting isochronous endpoint type.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This adds RCAR Gen2 USB phy support. The driver configures
USB channels 0/2 which are shared between PCI USB hosts and
USBHS/USBSS devices. It also controls internal USBHS phy.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So I captured this:
|WARNING: CPU: 0 PID: 2078 at /home/bigeasy/work/new/TI/linux/lib/debugobjects.c:260 debug_print_object+0x94/0xc4()
|ODEBUG: free active (active state 0) object type: work_struct hint: musb_irq_work+0x0/0x38 [musb_hdrc]
|CPU: 0 PID: 2078 Comm: rmmod Not tainted 3.12.0-rc4+ #338
|[<c0014d38>] (unwind_backtrace+0x0/0xf4) from [<c001249c>] (show_stack+0x14/0x1c)
|[<c001249c>] (show_stack+0x14/0x1c) from [<c0037720>] (warn_slowpath_common+0x64/0x84)
|[<c0037720>] (warn_slowpath_common+0x64/0x84) from [<c00377d4>] (warn_slowpath_fmt+0x30/0x40)
|[<c00377d4>] (warn_slowpath_fmt+0x30/0x40) from [<c022ae90>] (debug_print_object+0x94/0xc4)
|[<c022ae90>] (debug_print_object+0x94/0xc4) from [<c022b7e0>] (debug_check_no_obj_freed+0x1c0/0x228)
|[<c022b7e0>] (debug_check_no_obj_freed+0x1c0/0x228) from [<c00f1f38>] (kfree+0xf8/0x228)
|[<c00f1f38>] (kfree+0xf8/0x228) from [<c02921c4>] (release_nodes+0x1a8/0x248)
|[<c02921c4>] (release_nodes+0x1a8/0x248) from [<c028f70c>] (__device_release_driver+0x98/0xf0)
|[<c028f70c>] (__device_release_driver+0x98/0xf0) from [<c028f840>] (device_release_driver+0x24/0x34)
|[<c028f840>] (device_release_driver+0x24/0x34) from [<c028ebe8>] (bus_remove_device+0x148/0x15c)
|[<c028ebe8>] (bus_remove_device+0x148/0x15c) from [<c028d120>] (device_del+0x104/0x1c0)
|[<c028d120>] (device_del+0x104/0x1c0) from [<c02911e4>] (platform_device_del+0x18/0xac)
|[<c02911e4>] (platform_device_del+0x18/0xac) from [<c029179c>] (platform_device_unregister+0xc/0x18)
|[<c029179c>] (platform_device_unregister+0xc/0x18) from [<bf1902fc>] (dsps_remove+0x20/0x4c [musb_dsps])
|[<bf1902fc>] (dsps_remove+0x20/0x4c [musb_dsps]) from [<c0290d7c>] (platform_drv_remove+0x1c/0x24)
|[<c0290d7c>] (platform_drv_remove+0x1c/0x24) from [<c028f704>] (__device_release_driver+0x90/0xf0)
|[<c028f704>] (__device_release_driver+0x90/0xf0) from [<c028f818>] (driver_detach+0xb4/0xb8)
|[<c028f818>] (driver_detach+0xb4/0xb8) from [<c028e6e8>] (bus_remove_driver+0x98/0xec)
|[<c028e6e8>] (bus_remove_driver+0x98/0xec) from [<c008fc70>] (SyS_delete_module+0x1e0/0x24c)
|[<c008fc70>] (SyS_delete_module+0x1e0/0x24c) from [<c000e680>] (ret_fast_syscall+0x0/0x48)
|---[ end trace d79045419a3e51ec ]---
The workqueue is only scheduled from the ep0 and never canceled in case
the musb is removed before the work has a chance to run.
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
u_ms.ko is needed only together with usb_f_mass_storage.ko. Merge them.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no more old interface users left. Remove it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert the legacy multi gadget to the new interface of f_mass_storage,
so that later the compatibility layer in f_mass_storage can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert the legacy multi gadget to the new interface of f_rndis,
so that later the compatibility layer in f_rndis can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert the legacy multi gadget to the new interface of f_ecm,
so that later the compatibility layer in f_ecm can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert the legacy acm_ms gadget to use the new function interface
of f_mass_storage, so that later the compatibility layer in
f_mass_storage can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
From this commit on f_mass_storage is available through configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This will be required by configfs integration.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Show/store methods for sysfs attributes contain code which can be used
also by configfs. Make them abstract the source the lun and rw_semaphore
are taken from.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert old mass_storage gadget to use the new interface of f_mass_storage
so that later the compatibility layer in f_mass_storage can be removed.
struct fsg_common is not known to mass_storage.c, so a setter method
is added to f_mass_storage.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Converting mass storage to the new function interface requires converting
the USB mass storage's function code and its users.
This patch converts the f_mass_storage.c to the new function interface.
The file is now compiled into a separate usb_f_mass_storage.ko module.
The old function interface is provided by means of a preprocessor conditional
directives. After all users are converted, the old interface can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fsg_common_init is a lengthy function. Factor a portion of it out.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fsg_common_init is a lengthy function. Factor a portion of it out.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fsg_common_init is a lengthy function. Factor portions of it out.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fsg_common_init is a lengthy function. Factor a portion of it out.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fsg_common_init is a lengthy function. Factor portions of it out.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fsg_common_init is a lengthy function. Factor a portion of it out.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fsg_common_init is a lengthy function. Factor a portion of it out.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When configfs is in place, the luns will not be represented in sysfs,
so there will be no struct device associated with a lun.
In order to maintain compatibility and allow configfs adoption
sysfs is made optional in this patch.
As a consequence some debug macros need to be adjusted. Two new
fields are added to struct fsg_lun: name and name_pfx.
The "name" is for storing a string which is presented to the user
instead of the dev_name. The "name_pfx", if non-NULL, is prepended
to the "name" at printing time.
The name_pfx is for a future lun.0, which will be a default group in
mass_storage.<name>. By design at USB function configfs group's creation
time its name is not known (but instead set a bit later in
drivers/usb/gadget/configfs.c:function_make) and it is this name that
serves the purpose of the said name prefix. So instead of copying
a yet-unknown string a pointer to it is stored in struct fsg_lun.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When configfs is in place, gadgets will have to be able to free
fsg buffers. Add a helper function.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes max packet size check in s3c_hsotg_set_ep_maxpacket()
function. According USB specification, bits 10..0 of mps specifies maximum
packet size, so there is bitwise AND between mps and 0x7ff value. Also added
check if maxpacket isn't grater than 1024 which is maximum size od single USB
transaction.
In s3c_hsotg_ep_enable() function added s3c_hsotg_set_ep_maxpacket() call
instead of setting ep.maxpacket value directly.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If USB_FUNCTIONFS is selected without USB_FUNCTIONFS_ETH and
USB_FUNCTIONFS_RNIS, u_ether.h won't be included and then
USB_ETHERNET_MODULE_PARAMAETERS macro won't be available causing the
following warning compilation:
drivers/usb/gadget/g_ffs.c:81:1: warning: data definition has no type or
storage class [enabled by default]
drivers/usb/gadget/g_ffs.c:81:1: warning: type defaults to ‘int’ in
declaration of ‘USB_ETHERNET_MODULE_PARAMETERS’ [-Wimplicit-int]
drivers/usb/gadget/g_ffs.c:81:1: warning: function declaration isn’t a
prototype [-Wstrict-prototypes]
This patch fixes the warning by making USB_ETHERNET_MODULE_PARAMETERS to
be used iff u_ether.h is included, otherwise it is not needed.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Haswell LynxPoint and LynxPoint-LP with the recent Intel BIOS show
mysterious wakeups after shutdown occasionally. After discussing with
BIOS engineers, they explained that the new BIOS expects that the
wakeup sources are cleared and set to D3 for all wakeup devices when
the system is going to sleep or power off, but the current xhci driver
doesn't do this properly (partly intentionally).
This patch introduces a new quirk, XHCI_SPURIOUS_WAKEUP, for
fixing the spurious wakeups at S5 by calling xhci_reset() in the xhci
shutdown ops as done in xhci_stop(), and setting the device to PCI D3
at shutdown and remove ops.
The PCI D3 call is based on the initial fix patch by Oliver Neukum.
[Note: Sarah changed the quirk name from XHCI_HSW_SPURIOUS_WAKEUP to
XHCI_SPURIOUS_WAKEUP, since none of the other quirks have system names
in them. Sarah also fixed a collision with a quirk submitted around the
same time, by changing the xhci->quirks bit from 17 to 18.]
This patch should be backported to kernels as old as 3.0, that
contain the commit 1c12443ab8 "xhci: Add
Lynx Point to list of Intel switchable hosts."
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The function pci_write_config_dword() sets the appropriate byteordering
internally so the value argument should not be converted to little-endian.
This bug was found by sparse.
This patch is not suitable for stable. Since cpu_to_lei32 is a no-op on
little endian systems, this bug would only affect big endian Intel
systems with the EHCI to xHCI port switchover, which are non-existent,
AFAIK.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
