Here is the big USB and Thunderbolt and PHY driver updates for 5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code has
begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFTNw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynpKQCgrh2FoobS2x0oFg/OUHdjokQV/BYAoJGWLOmt
8S5cnsCuLq3w5qpCcBva
=PMGd
-----END PGP SIGNATURE-----
Merge tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt/PHY driver updates from Greg KH:
"Here is the big USB and Thunderbolt and PHY driver updates for
5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code
has begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues"
[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
that causes configuration warnings - Linus ]
* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
Doc: ABI: add usb charger uevent
usb: phy: show USB charger type for user
usb: cdns3: fix spelling mistake and rework grammar in text
usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
usb: typec: tcpci: mask event interrupts when remove driver
usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
usb: chipidea: handle single role for usb role class
usb: musb: fix spelling mistake: "periperal" -> "peripheral"
phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
USB: usbfs: Always unlink URBs in reverse order
...
If CONFIG_OF_ADDRESS is not set and COMPILE_TEST=y, the following
error is seen while building phy-j721e-wiz.c
drivers/phy/ti/phy-j721e-wiz.o: In function `wiz_remove':
phy-j721e-wiz.c:(.text+0x1a): undefined reference to
`of_platform_device_destroy'
Fix the config dependency for PHY_J721E_WIZ here.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20200117212310.2864-1-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
*) Add support in PHY core to create link between PHY consumer and PHY
provider
*) Add DisplayPort PHY configuration set to be used for negotiating the
configurations to be used between DisplayPort controller and
DisplayPort PHY
*) Add PHY wrapper driver (configure inputs to Cadence Sierra PHY) for
TI's J721E SoC and adapt Cadence Sierra PHY driver to be used for
J721E SoC (Supports USB and PCIe)
*) Add PHY driver for eMMC PHY in Intel LGM SoC
*) Add PHY support for 7216 and 7211 Broadcom SoCs which uses the new
Synopsys USB Controller
*) Add support for 16nm SATA PHY present in Broadcom 7216 SoC
*) Fix lost packet issue, fix MDIO from getting inaccessible, fix
occasional transaction failures, fix USB driver from crashing in
Broadcom USB PHY driver
*) Fix missing PCS SW reset in UFS PHY of Qualcomm SM8150
*) Use "struct phy_configure_opts_mipi_dphy" to pass parameters from
display controller to rockchip-inno-dsidphy
*) Other cleanups including compile testing for some of the PHY drivers,
fixing Kconfig indentation, duplicate writes in drivers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=76zg
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.6
*) Add support in PHY core to create link between PHY consumer and PHY
provider
*) Add DisplayPort PHY configuration set to be used for negotiating the
configurations to be used between DisplayPort controller and
DisplayPort PHY
*) Add PHY wrapper driver (configure inputs to Cadence Sierra PHY) for
TI's J721E SoC and adapt Cadence Sierra PHY driver to be used for
J721E SoC (Supports USB and PCIe)
*) Add PHY driver for eMMC PHY in Intel LGM SoC
*) Add PHY support for 7216 and 7211 Broadcom SoCs which uses the new
Synopsys USB Controller
*) Add support for 16nm SATA PHY present in Broadcom 7216 SoC
*) Fix lost packet issue, fix MDIO from getting inaccessible, fix
occasional transaction failures, fix USB driver from crashing in
Broadcom USB PHY driver
*) Fix missing PCS SW reset in UFS PHY of Qualcomm SM8150
*) Use "struct phy_configure_opts_mipi_dphy" to pass parameters from
display controller to rockchip-inno-dsidphy
*) Other cleanups including compile testing for some of the PHY drivers,
fixing Kconfig indentation, duplicate writes in drivers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (54 commits)
dt-bindings: phy: Add PHY_TYPE_DP definition
phy: ti: j721e-wiz: Fix return value check in wiz_probe()
dt-bindings: usb: Convert Allwinner A80 USB PHY controller to a schema
phy: intel-lgm-emmc: Fix warning by adding missing MODULE_LICENSE
phy: ti: j721e-wiz: Manage typec-gpio-dir
dt-bindings: phy: ti,phy-j721e-wiz: Add Type-C dir GPIO
phy: cadence: Sierra: add phy_reset hook
phy: cadence: Sierra: remove redundant initialization of pointer regmap
phy: Add DisplayPort configuration options
phy: Enable compile testing for some of drivers
phy: mediatek: Fix Kconfig indentation
phy: intel-lgm-emmc: Add support for eMMC PHY
dt-bindings: phy: intel-emmc-phy: Add YAML schema for LGM eMMC PHY
phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC
dt-bindings: phy: Document WIZ (SERDES wrapper) bindings
phy: cadence: Sierra: Use correct dev pointer in cdns_sierra_phy_remove()
phy: cadence: Sierra: Set cmn_refclk_dig_div/cmn_refclk1_dig_div frequency to 25MHz
phy: cadence: Sierra: Change MAX_LANES of Sierra to 16
phy: cadence: Sierra: Check for PLL lock during PHY power on
phy: cadence: Sierra: Get reset control "array" for each link
...
In case of error, the function devm_ioremap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
commit 95f1061f715e ("phy: intel-lgm-emmc: Add support for eMMC PHY")
introduces the below warning
WARNING: modpost: missing MODULE_LICENSE() in
drivers/phy/intel/phy-intel-emmc.o
Fix it by adding missing MODULE_LICENSE.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on this GPIO state we need to configure LN10
bit to swap lane0 and lane1 if required (flipped connector).
Type-C companions typically need some time after the cable is
plugged before and before they reflect the correct status of
Type-C plug orientation on the DIR line.
Type-C Spec specifies CC attachment debounce time (tCCDebounce)
of 100 ms (min) to 200 ms (max).
Use the DT property to figure out if we need to add delay
or not before sampling the Type-C DIR line.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some platforms e.g. J721e need lane swap register
to be programmed before reset is deasserted.
This patch ensures that we propagate the phy_reset
back to the reset controller driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The pointer regmap is being initialized with a value that is never
read and it is being updated later with a new value from
phy->regmap_common_cdb. The initialization is redundant and can be
removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some of the phy drivers can be compile tested to increase build
coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for eMMC PHY on Intel's Lightning Mountain SoC.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for WIZ module present in TI's J721E SoC. WIZ is a SERDES
wrapper used to configure some of the input signals to the SERDES. It is
used with both Sierra(16G) and Torrent(10G) SERDES. This driver configures
three clock selects (pll0, pll1, dig), two divider clocks and supports
resets for each of the lanes.
[jsarha@ti.com: Add support for Torrent(10G) SERDES wrapper]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
commit 44d30d6228 ("phy: cadence: Add driver for Sierra PHY"),
incorrectly used parent device pointer to get driver data. Fix it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Set cmn_refclk_dig_div/cmn_refclk1_dig_div frequency to 25MHz
as specified in "Common Module Clock Configurations" of the Cadence
Sierra 16FFC Multi-Protocol PHY PMA Specification. It is set to 25MHz
since the only user of Cadence Sierra SERDES, TI J721E SoC provides
input clock frequency of 100MHz. For other frequencies,
cmn_refclk_dig_div/cmn_refclk1_dig_div should be configured
based on the "Common Module Clock Configurations".
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Sierra SERDES IP supports upto 16 lanes (though not all of it
will be enabled in a platform). Allow Sierra driver to support a
maximum of upto 16 lanes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
A link may have multiple lanes each with a separate reset. Get
reset control "array" in order to reset all the lanes associated
with the link.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The existing configuration done in Cadence Sierra driver is only for
reference and is not used in any platforms. Remove them and configure
both lane cdb and common cdb registers to be used with external
SSC configuration. This is validated in TI J721E platform.
Signed-off-by: Anil Varughese <aniljoy@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Instead of invoking cdns_sierra_phy_init() from probe, add it in
phy_ops so that it's initialized when the PHY consumer invokes
phy_init()
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
SERDES_16G in TI's J721E SoC uses Cadence Sierra PHY. Add
support to use Cadence Sierra driver in J721E SoC.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use "regmap" for read and write to Sierra registers. This is in
perparation for adding SERDES_16G support present in TI's J721E
SoC.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Certain platforms like TI J721E using Cadence Sierra Serdes
doesn't provide explicit phy_clk and reset (APB reset) control.
Make them optional here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for 7211 USB wake. Disable all possible 7211 USB logic
for S2/S5 if USB wake is not enabled.
On the 7211, the XHCI wake signal was not connected properly and
only goes to the USB1_USB1_CTRL_TP_DIAG1 diagonstic register.
The workaround is to have VPU code running that polls for the
proper bit in the DIAG register and to wake the system when
the bit is asserted.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is a result of the USB 2.0 clocks not being disabled/enabled
during suspend/resume on XHCI only systems.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The BDC "Read Transaction Size" needs to be changed from 1024
bytes to 256 bytes to prevent occasional transaction failures.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When there is no device connected and FSM is enabled, the XHCI puts
the PHY into suspend mode. When the PHY is put into suspend mode
the USB LDO powers down the PHY. This causes the MDIO to be
inaccessible and its registers reset to default. The fix is to
disable FSM.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Handle defer on clk_get because the new SCMI clock driver comes
up after this driver.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The 7211b0 has added the STB XHCI Synopsys controller and it
will be used instead of the RPi based DWC USB controller. The new
Synopsys XHCI controller core is the same one that is used on the
7216, but because of the way the STB USB PHY is used on both the A0
and B0, some of the PHY control is different.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The 7216 has the new USB XHCI controller from Synopsys. While
this new controller and the PHY are similar to the STB versions,
the major differences are:
- Many of the registers and fields in the CTRL block have been
removed or changed.
- A new set of Synopsys control registers, BCHP_USB_XHCI_GBL, were
added.
- MDIO functionality has been replaced with direct access registers
in the BCHP_USB_XHCI_GBL block.
- Power up PHY defaults that had to be changed by MDIO in previous
chips will now power up with the correct defaults.
A new init module was created for this new Synopsys USB controller.
A new compatible string was added and the driver will dispatch
into one of two init modules based on it. A "reg-names" field was
added so the driver can more easily get optional registers.
A DT bindings document was also added for this driver.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The driver is being restructured in preparation for adding support
for the new Synopsys USB conroller on the 7216. Since all the bugs
and work-arounds in previous STB chips are supposed to be fixed,
most of the code in phy-brcm-usb-init.c is not needed. Instead of
adding more complexity to the already complicated phy-brcm-usb-init.c
module, the driver will be restructured to use a vector table to
dispatch into different C modules for the different controllers.
There was also some general cleanup done including some ipp setup
code that was incorrect.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add the ability to handle USB wake events from USB devices when
in S2 mode. Typically there is some additional configuration
needed to tell the USB device to generate the wake event when
suspended but this varies with the different USB device classes.
For example, on USB Ethernet dongles, ethtool should be used to
enable the magic packet wake functionality in the dongle.
NOTE: This requires that the "power/wakeup" sysfs entry for
the USB device generating the wakeup be set to "enabled".
This functionality requires a special hardware sideband path that
will trigger the AON_PM_L2 interrupt needed to wake the system from
S2 even though the USB host controllers are in IDDQ (low power state)
and most USB related clocks are shut off. For the sideband signaling
to work we need to leave the usbx_freerun clock running, but this
clock consumes very little power by design. There's a bug in the
XHCI wake hardware so only EHCI/OHCI wake is currently supported.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently the Phy driver will put the USB phys into the max
power saving mode (IDDQ) when there is no corresponding XHCI, EHCI
or OHCI client (through rmmod, unbind or if the driver is not
builtin). This change will also put the Phys into IDDQ mode
on suspend so that S2 will get the additional power savings.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The BRCM USB Phy, ohci, ehci and xhci drivers all use the USB clocks
but not all drivers use the clk_prepare_enable/clk_disable_unprepare
versions to enable/disable the clocks. This change gets all drivers
using the prepare version.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When the EHCI controller received a 512 byte USB packet that
had to be broken into 2 256 byte bursts across the SCB bus AND
there was a following 512 byte USB packet, the second burst of
data from the first packet was sometimes being lost. If the
burst size was changed to 128 bytes via the EBR_SCB_SIZE field
in the USB_CTRL_EBRIDGE register we'd see the 4th 128 byte burst
of the first packet being lost. This problem became much worse
if other threads were running that accessed memory, like a memcpy
test. Setting the EBR_SCB_SIZE to 512, which prevents breaking
the EHCI USB packet (max size of 512 bytes) into bursts, fixed
the problem.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
For V4 QMP UFS Phy, we need to assert reset bits, configure the phy and
then deassert it, so add the QPHY_SW_RESET register which does this.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
SM8150 QMPY phy for UFS and onwards the PHY_SW_RESET is present in PHY's
PCS register so we should not mark no_pcs_sw_reset for sm8150 and
onwards
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We already write to QPHY_POWER_DOWN_CONTROL in qcom_qmp_phy_com_init()
before invoking qcom_qmp_phy_configure() so remove the duplicate write.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We already define register offsets so use them in register layout.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
7216 is a 16nm process chip with a slightly different version of the PHY
SerdDeS/AFE that requires a specific tuning sequence. Key on the
compatible string to perform that initialization.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
During review it came to light that exposing the pll clock outside is
not the right approach and struct phy_configure_opts_mipi_dphy exists
just for that reason to transfer parameters to the phy.
So drop the exposed clock and rely on the phy configure options
to bring in the correct rate. That way we can also just drop the
open coded timing struct and default values function.
Fixes: b7535a3bc0 ("phy/rockchip: Add support for Innosilicon MIPI/LVDS/TTL PHY")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fixes coccicheck warning:
drivers/phy/lantiq/phy-lantiq-vrx200-pcie.c:389:2-3: Unneeded semicolon
Fixes: e52a632195 ("phy: lantiq: vrx200-pcie: add a driver for the Lantiq VRX200 PCIe PHY")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ma Feng <mafeng.ma@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Clang warns:
../drivers/phy/qualcomm/phy-qcom-apq8064-sata.c:83:4: warning:
misleading indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50);
^
../drivers/phy/qualcomm/phy-qcom-apq8064-sata.c:80:3: note: previous
statement is here
if (readl_relaxed(addr) & mask)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 1de990d8a1 ("phy: qcom: Add driver for QCOM APQ8064 SATA PHY")
Link: https://github.com/ClangBuiltLinux/linux/issues/816
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In order to enforce suspend/resume ordering, this commit creates link
between phy consumers and phy devices. This link avoids to suspend phy
before phy consumers.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
[jonathanh@nvidia.com: Fix an abort when of_phy_get() returns error]
Signed-off-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some of the phy drivers can be compile tested to increase build
coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200103164710.4829-2-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch network drivers, phy drivers, and SFP/phylink over to use the
more correct 10GBASE-R, rather than 10GBASE-KR. 10GBASE-KR is backplane
ethernet, which is 10GBASE-R with autonegotiation on top, which our
current usage on the affected platforms does not have.
The only remaining user of PHY_INTERFACE_MODE_10GKR is the Aquantia
PHY, which has a separate mode for 10GBASE-KR.
For Marvell mvpp2, we detect 10GBASE-KR, and rewrite it to 10GBASE-R
for compatibility with existing DT - this is the only network driver
at present that makes use of PHY_INTERFACE_MODE_10GKR.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 287422a95f ("drm/rockchip: Round up _before_ giving to the clock framework")
changed what rate clk_round_rate() is called with, an additional 999 Hz
added to the requsted mode clock. This has caused a regression on RK3328
and presumably also on RK3228 because the inno-hdmi-phy clock requires an
exact match of the requested rate in the pre pll config table.
When an exact match is not found the parent clock rate (24MHz) is returned
to the clk_round_rate() caller. This cause wrong pixel clock to be used and
result in no-signal when configuring a mode on RK3328.
Fix this by rounding the rate down to closest 1000 Hz in round_rate func,
this allows an exact match to be found in pre pll config table.
Fixes: 287422a95f ("drm/rockchip: Round up _before_ giving to the clock framework")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
