The test-unit-ready portion of this patch was causing boots to fail on
my test machine (as in http://lkml.org/lkml/2008/12/5/161). With this
patch in place, the system is booting reliably.
Mike Anderson found the same problem in the hp_hw_start_stop code,
and I applied the same solution in cdrom_read_cdda_bpc.
Signed-off-by: Alan D. Brunelle <alan.brunelle@hp.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
During a reset, releasing the swflag after it failed to be acquired would
cause a double unlock of the mutex. Instead, test whether acquisition of
the swflag was successful and if not, do not release the swflag. The reset
must still be done to bring the device to a quiescent state.
This resolves [BUG 12200] BUG: bad unlock balance detected! e1000e
http://bugzilla.kernel.org/show_bug.cgi?id=12200
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tmp is used as host-endian and is loaded from a be64, fix the cast and the
endian accessor used.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This reverts commit b1ee26bab1, along with
the "fixes" for it that all just caused problems:
- c4c6fa9891 "radeonfb: fix problem with
color expansion & alignment"
- f3179748a1 "radeonfb: Disable new color
expand acceleration unless explicitely enabled"
because even when disabled, it breaks for people. See
http://bugzilla.kernel.org/show_bug.cgi?id=12191
for the latest example.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: James Cloos <cloos@jhcloos.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Jean-Luc Coulon <jean.luc.coulon@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCIe: ASPM: Break out of endless loop waiting for PCI config bits to switch
PCI: stop leaking 'slot_name' in pci_create_slot
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] SN: prevent IRQ retargetting in request_irq()
[IA64] Fix section mismatch ioc3uart_init()/ioc3uart_submodule
[IA64] Clear up section mismatch for ioc4_ide_attach_one.
[IA64] Clear up section mismatch with arch_unregister_cpu()
[IA64] Clear up section mismatch for sn_check_wars.
[IA64] Updated the generic_defconfig to work with the 2.6.28-rc7 kernel.
[IA64] Fix GRU compile error w/o CONFIG_HUGETLB_PAGE
[IA64] eliminate NULL test and memset after alloc_bootmem
[IA64] remove BUILD_BUG_ON from paravirt_getreg()
The pktcdvd created class devices only export some sysfs files,
but have no char dev_t registered in the driver.
At class device creation time they copy the dev_t value of the
block device to the char device, wich will register a new char
device in the driver core and userspace, with a conflicting dev_t
value.
In many cases the class devices dev_t just points to a random
USB device. This fixes the sysfs "duplicate entry" errors.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Peter Osterlund <petero2@telia.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sparc64:
drivers/video/mb862xx/mb862xxfb.c:929: warning: long long unsigned int format, resource_size_t arg (arg 4)
drivers/video/mb862xx/mb862xxfb.c:931: warning: long long unsigned int format, resource_size_t arg (arg 4)
We don't know what type the architecture uses to implement u64, hence they
cannot be printed.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Matteo Fortini <m.fortini@selcomgroup.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix build error when RTC_INTF_DEV=n:
drivers/rtc/rtc-twl4030.c:402: error: 'twl4030_rtc_ioctl' undeclared here (not in a function)
make[3]: *** [drivers/rtc/rtc-twl4030.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a call to cancel_work_sync() in fbcon_exit() to cancel any pending
work in the fbcon workqueue.
The current implementation of fbcon_exit() sets the fbcon workqueue
function info->queue.func to NULL, but does not assure that there is no
work pending when it does so. On occasion, depending on system timing,
there will still be pending work in the queue when fbcon_exit() is
called. This results in a null pointer deference when run_workqueue()
tries to call the queue's work function.
Fixes errors on shutdown similar to these:
Console: switching to colour dummy device 80x25
Unable to handle kernel paging request for data at address 0x00000000
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add missing id_table to the drivers in subject. Patch is against the
latest git. It should go in with 2.6.28 if possible, the drivers won't
work without the id_table bits.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Reported-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Imre Kaloz <kaloz@openwrt.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a DMA map/ unmap imbalance whenever a block write request
packet is sent and then dequeued with ohci_cancel_packet. The latter
may happen frequently if the AR resp tasklet is executed before the AT
req tasklet for the same transaction.
Add the missing dma_unmap_single. This fixes
https://bugzilla.redhat.com/show_bug.cgi?id=475156
Reported-by: Emmanuel Kowalski
Tested-by: Emmanuel Kowalski
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
From: Hermann Lauer <Hermann.Lauer@iwr.uni-heidelberg.de>
Attached is a patch which improves the output of ethtool (see below)
to some sensefull values with a sungem fibre card which uses the
sungem interal pcs connected to a serdes chip. The seriallink case in
the driver is untouched.
Most values are hardcoded, because gigabit fibre autoneg is anyways
limited and the driver don't really support much at the moment with
that hardware.
Signed-off-by: David S. Miller <davem@davemloft.net>
Makes a Compaq 6735s boot reliably again. It used to hang in the loop
on some boots. Give the link one second to train, otherwise break out
of the loop and reset the previously set clock bits.
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In pci_create_slot(), the local variable 'slot_name' is allocated by
make_slot_name(), but never freed. We never use it after passing it to
the kobject core, so we should free it upon function exit.
Cc: stable@kernel.org
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The firewire nodemanager function "nodemgr_host_thread" contains a loop
that calls try_to_freeze near the top of the loop, but then delays for
up to 3.25 seconds (plus time to do work) before getting back to the top
of the loop. When starting a cycle post-boot, this doesn't seem to bite,
but it is causing a noticeable delay at boot time, when freezing
processes prior to starting to read the image.
The following patch adds invocation of try_to_freeze to the subloops
that are used in the body of this function. With these additions, the
time to freeze when starting to resume at boot time is virtually zero.
I'm no expert on firewire, and so don't know that we shouldn't check
the return value and jump back to the top of the loop or such like after
being frozen, but I submit it for your consideration.
Signed-off-by: Nigel Cunningham <nigel@tuxonice.net>
The delay until nodemgr freezes was up to 0.25s (plus time for node
probes) in Linux 2.6.27 and older and up to 3.25s (plus ~) since Linux
2.6.28-rc1, hence much more noticeable.
try_to_freeze() without any jump is correct. The surrounding code in
the respective loops will catch whether another bus reset happens during
the freeze and handle it.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The generic_defconfig has three section mismatches. This clears up
ioc4_ide_attach_one().
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Mike Reid <mdr@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Eliminate compile error when compiling without CONFIG_HUGETLB_PAGE.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] Fix alignment fault handling for ARMv6 and later CPUs
[ARM] 5340/1: fix stack placement after noexecstack changes
[ARM] 5339/1: fix __fls() on ARM
[ARM] Orion: fix bug in pcie configuration cycle function field mask
[ARM] omap: fix a pile of issues
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Disable the GM965 MSI errata workaround.
drm/i915: Don't return error in evict_everything when we get to the end.
drm/radeon: don't actually enable the IRQ regs until irq is enabled
This new color expansion acceleration for radeonfb appears to trigger
problems with X on VT switch and suspend/resume on some machines. It
might be a problem in the VT layer or in X, but I haven't quite found
it yet, so in the meantime, this disables the acceleration by default,
reverting to 2.6.27 state. It can be enabled using the "accel_cexp"
module parameter or fbdev argument.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Calling crq_queue_create could lead to the creation of a rport. We
need to set up everything before creating a rport. This moves
crq_queue_create to the end of initialization to avoid a race which
causes an oops if lost.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reported-by: Olaf Hering <olh@suse.de>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As reported by Hermann Lauer, PCS PHY support in the sungem
driver simply doesn't work.
When the chip is reset due to open, or some other similar operation,
the PCS is reset too but we don't program it back into a running
state. The result is no link when the device is brought up.
This partially rectifies the situation for the moment, by kicking
the PCS after a sungem chip reset so that it will renegotiate and
be re-enabled again.
The behavior is still a little bit dodgy as the added renegotiate
make the link take some time after bringing the interface up,
but this is a significant improvement in that things actually work
now :-)
Based almost entirely upon an initial patch by Hermann.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems report SIS 5513 as both vendor/id and subvendor/id
string. In that case we can't distinguish the system by the id
svid/sdid and in fact the entry here breaks some boxes. At some
point we need to find another way to detect the Targa Visionary 1000,
until then this trades a hang for some users with lower performance
for others.
Closes: #12092
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Hi,
I've found this issue in the mmotm 2008-12-02-17-08.
--
Commit
ata_piix: add borked Tecra M4 to broken suspend list
introduced DMI variables checking, but they can be null, so that
we possibly dereference null.
Check if they are null and avoid checks in that case.
Solves:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
IP: [<ffffffff8043da97>] piix_pci_device_suspend+0x117/0x230
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_hpt366 had its clock detection wrong and detected 25Mhz as 40Mhz
and vice-versa. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since applying the fix suggested by the errata (disabling MSI), we've had
issues with interrupts being stuck on despite IIR being 0 on GM965 hardware.
Most reporters of the issue have confirmed that turning MSI back on fixes
things, and given the difficulties experienced in getting reliable MSI working
on Linux, it's believable that the errata was about software issues and not
actual hardware issues.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
tproxy: fixe a possible read from an invalid location in the socket match
zd1211rw: use unaligned safe memcmp() in-place of compare_ether_addr()
mac80211: use unaligned safe memcmp() in-place of compare_ether_addr()
ipw2200: fix netif_*_queue() removal regression
iwlwifi: clean key table in iwl_clear_stations_table function
tcp: tcp_vegas ssthresh bug fix
can: omit received RTR frames for single ID filter lists
ATM: CVE-2008-5079: duplicate listen() on socket corrupts the vcc table
netx-eth: initialize per device spinlock
tcp: make urg+gso work for real this time
enc28j60: Fix sporadic packet loss (corrected again)
hysdn: fix writing outside the field on 64 bits
b1isa: fix b1isa_exit() to really remove registered capi controllers
can: Fix CAN_(EFF|RTR)_FLAG handling in can_filter
Phonet: do not dump addresses from other namespaces
netlabel: Fix a potential NULL pointer dereference
bnx2: Add workaround to handle missed MSI.
xfrm: Fix kernel panic when flush and dump SPD entries
Mapping the destination multiple times is a misuse of the dma-api.
Since the destination may be reused as a source, ensure that it is only
mapped once and that it is mapped bidirectionally. This appears to add
ugliness on the unmap side in that it always reads back the destination
address from the descriptor, but gcc can determine that dma_unmap is a
nop and not emit the code that calculates its arguments.
Cc: <stable@kernel.org>
Cc: Saeed Bishara <saeed@marvell.com>
Acked-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
IDE pmac host driver build fails with CONFIG_BLK_DEV_IDEDMA_PMAC=n
as reported by Kamalesh:
> drivers/ide/pmac.c: In function 'pmac_ide_set_pio_mode':
> drivers/ide/pmac.c:527: error: implicit declaration of function 'kauai_lookup_timing'
> drivers/ide/pmac.c:527: error: 'shasta_pio_timings' undeclared (first use in this function)
> drivers/ide/pmac.c:527: error: (Each undeclared identifier is reported only once
> drivers/ide/pmac.c:527: error: for each function it appears in.)
> drivers/ide/pmac.c:534: error: 'kauai_pio_timings' undeclared (first use in this function)
> drivers/ide/pmac.c: In function 'pmac_ide_do_resume':
> drivers/ide/pmac.c:914: error: 'IDE_WAKEUP_DELAY' undeclared (first use in this function)
> drivers/ide/pmac.c: At top level:
> drivers/ide/pmac.c:1007: error: 'pmac_ide_init_dma' undeclared here (not in a function)
> drivers/ide/pmac.c: In function 'pmac_ide_setup_device':
> drivers/ide/pmac.c:1107: error: 'IDE_WAKEUP_DELAY' undeclared (first use in this function)
> drivers/ide/pmac.c: In function 'pmac_ide_macio_attach':
> drivers/ide/pmac.c:1209: error: 'pmac_ide_hwif_t' has no member named 'dma_regs'
> drivers/ide/pmac.c:1210: error: 'pmac_ide_hwif_t' has no member named 'dma_regs'
> make[2]: *** [drivers/ide/pmac.o] Error 1
Fix it by removing the superfluous config option.
Reported-and-tested-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This reverts commit e9eb838830 since
it could break resume (thanks to Paul Collins for the report).
I'll look into sorting this out properly for 2.6.29
but for 2.6.28 it is the best to just revert my patch.
Reported-by: Paul Collins <paul@burly.ondioline.org>
Cc: rjw@sisk.pl
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
no argument named @msg in i2o_msg_get_wait(), remove it.
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix incorrect use of loose in i2o_block.c
It should be 'lose', not 'loose'.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[Folded together as one diff from 3]
It should be 'lose', not 'loose'.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 558073dd56, along with
the failed try to fix the regression it caused ("ACPI: Fix ACPI battery
regression introduced by commit 558073"), which just made things worse.
Commit aaad077638 (that failed "Fix ACPI
battery regression") got the voltage conversion confused, and fixed the
problem with Rafael's battery monitor apparently just by mistake.
So revert them both, getting us back to the 2.6.27 state in this, and
let's revisit it when people understand what's going on.
Noted-by: Paul Martin <pm@debian.org>
Requested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Cc: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Under my 2.6.28-rc6 sparc64, when associating to an AP through my
zd1211rw device, I was seeing kernel log messages like (not exact output):
Kernel unaligned access at TPC[10129b68] zd_mac_rx+0x144/0x32c [zd1211rw]
For the zd1211rw module, on RX, the 80211 packet will be located after
the PLCP header in the skb data buffer. The PLCP header being 5 bytes
long, the 80211 header will start unaligned from an aligned skb
buffer.
As per Documentation/unaligned-memory-access.txt, we must replace the
not unaligned() safe compare_ether_addr() with memcmp() to protect
architectures that require alignment.
Signed-off-by: Shaddy Baddah <shaddy_baddah@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "ipw2200: Call netif_*_queue() interfaces properly", netif_stop_queue()
and netif_wake_queue() were removed with the reason
"netif_carrier_{on,off}() handles starting and stopping packet flow into
the driver". The patch also removes a valid condition check that
ipw_tx_skb() cannot be called if device is not in STATUS_ASSOCIATED state.
But netif_carrier_off() doesn't guarantee netdev->hard_start_xmit won't
be called because linkwatch event is handled in a delayed workqueue. This
caused a kernel oops reported by Frank Seidel:
https://bugzilla.novell.com/show_bug.cgi?id=397390
This patch fixes the problem by moving the STATUS_ASSOCIATED check back
to ipw_tx_skb(). It also adds a missing netif_carrier_off() call to
ipw_disassociate().
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Chatre, Reinette <reinette.chatre@intel.com>
Tested-by: Frank Seidel <fseidel@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans uCode key table bit map iwl_clear_stations_table
since all stations are cleared also the key table must be.
Since the keys are not removed properly on suspend by mac80211
this may result in exhausting key table on resume leading
to memory corruption during removal
This patch also fixes a memory corruption problem reported in
http://marc.info/?l=linux-wireless&m=122641417231586&w=2 and tracked in
http://bugzilla.kernel.org/show_bug.cgi?id=12040.
When the key is removed a second time the offset is set to 255 - this
index is not valid for the ucode_key_table and corrupts the eeprom pointer
(which is 255 bits from ucode_key_table).
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Reported-by: Lukas Hejtmanek <xhejtman@ics.muni.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/bdev:
[PATCH] fix bogus argument of blkdev_put() in pktcdvd
[PATCH 2/2] documnt FMODE_ constants
[PATCH 1/2] kill FMODE_NDELAY_NOW
[PATCH] clean up blkdev_get a little bit
[PATCH] Fix block dev compat ioctl handling
[PATCH] kill obsolete temporary comment in swsusp_close()
* 'drm-gem-update' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Return error in i915_gem_set_to_gtt_domain if we're not in the GTT.
drm/i915: Retry execbuffer pinning after clearing the GTT
drm/i915: Move the execbuffer domain computations together
drm/i915: Rename object_set_domain to object_set_to_gpu_domain
drm/i915: Make a single set-to-cpu-domain path and use it wherever needed.
drm/i915: Make a single set-to-gtt-domain path.
drm/i915: If interrupted while setting object domains, still emit the flush.
drm/i915: Move flushing list cleanup from flush request retire to request emit.
drm/i915: Respect GM965/GM45 bit-17-instead-of-bit-11 option for swizzling.
Commit 558073dd56 ("ACPI: battery: Convert
discharge energy rate to current properly") caused the battery subsystem
to report wrong values of the remaining time on battery power and the
time until fully charged on Toshiba Portege R500 (and presumably on
other boxes too).
Fix the issue by correcting the conversion from mW to mA.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
final close of ->bdev should match the initial open, i.e.
get FMODE_READ | FMODE_NDELAY; FMODE_READ|FMODE_WRITE has
been a braino.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Update FMODE_NDELAY before each ioctl call so that we can kill the
magic FMODE_NDELAY_NOW. It would be even better to do this directly
in setfl(), but for that we'd need to have FMODE_NDELAY for all files,
not just block special files.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The spinlock used in the netx-eth driver was never properly initialized.
This was noticed using CONFIG_DEBUG_SPINLOCK=y
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet data read from the RX buffer the when the RSV is at the end of the RX
buffer does not warp around. This causes packet loss, as the actual data is
never read. Fix this by calculating the right packet data location.
Thanks to Shachar Shemesh for suggesting the fix.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ifa_local is assumed to be unsigned long which lead to writing the address
at dev->dev_addr-2 instead of +2
noticed thanks to gcc:
drivers/isdn/hysdn/hysdn_net.c: In function `net_open':
drivers/isdn/hysdn/hysdn_net.c:91: warning: array subscript is below array bounds
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's only for flushing caches appropriately for GTT access, not for actually
getting it there. Prevents potential smashing of cpu read/write domains on
unbound objects.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we fail to pin all of the buffers in an execbuffer request, go through
and clear the GTT and try again to see if its just a matter of fragmentation
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This eliminates the dev_set_domain function and just in-lines it
where its used, with the goal of moving the manipulation and use of
invalidate_domains and flush_domains closer together. This also
avoids calling add_request unless some domain has been flushed.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that the CPU and GTT domain operations are isolated to their own
functions, the previously general-purpose set_domain function is now used
only to set GPU domains. It also has no failure cases, which is important as
this eliminates any possible interruption of the computation of new object
domains and subsequent emmission of the flushing instructions into the ring.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes several domain management bugs, including potential lack of cache
invalidation for pread, potential failure to wait for set_domain(CPU, 0),
and more, along with producing more intelligible code.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes failure to flush caches in the relocation update path, and
failure to wait in the set_domain ioctl, each of which could lead to incorrect
rendering.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise, we would leave the objects in an inconsistent state, such as
write_domain == 0 but on the flushing list.
Signed-off-by: Dave Airlie <airlied@redhat.com>
obj_priv->write_domain is "write domain if the GPU went idle now", not
"write domain at this moment." By postponing the clear, we confused the
concept, required more storage, and potentially emitted more flushes than
are required.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes readpixels and buffer corruption when swapped out and in by
disabling tiling on them.
Now that we know that the bit 17 mode isn't just a mistake of older chipsets,
we'll need to work on a clever fix so that we can get the performance of
tiling on these chipsets, but that will require intrusive changes targeted
at the next kernel release, not this one.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: fix setting of max_segment_size and seg_boundary mask
block: internal dequeue shouldn't start timer
block: set disk->node_id before it's being used
When block layer fails to map iov, it calls bio_unmap_user to undo
There is a possibility to have two devices registered with the same id.
Cc: <stable@kernel.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The code used '&= 0x00002000' when it tried to set the TCO_EN bit, which
obviously didn't set that bit at all, but instead just reset all the
other bits in the SMI_EN register.
This bug seemingly caused various random behavior, with Frans Pop
reporting that X.org just silently hung at startup and Rafael Wysocki
reports the fan spinning with full speed.
See
http://lkml.org/lkml/2008/12/3/178http://bugzilla.kernel.org/show_bug.cgi?id=12162
The problem seems to have been triggered by "[WATCHDOG] iTCO_wdt :
problem with rebooting on new ICH9 based motherboards" (commit
7cd5b08be3), but the bogus code existed
before that too (in the "supermicro_old_pre_stop()" function), it just
apparently never showed up due to different logic.
In that commit the broken code got moved around and now gets executed
much more.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Frans Pop <elendil@planet.nl>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As part of the ioat_dma self-test it performs a printk from a completion
callback. Depending on the system console configuration this output can
take longer than a millisecond causing the self-test to fail. Introduce a
completion with a generous timeout to mitigate this failure.
Cc: <stable@kernel.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This regression was added in 2.6.27, when the mtask and ctask were
merged into the the common task struct. The patch applies to
scsi-rc-fixes, but also applies to 2.6.27 with some offsets.
The problem is that __iscsi_conn_send_pdu assumes that userspace was
not sending nops with the format it is checking for in the "if" below.
It turns out that older userspace tools are. This patch moves the
setting of the internal ping_task tracker (it tracks libiscsi current
outstanding nop) to iscsi_send_nopout which is only used by kernel callers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
A lot of 64bit machines with Adaptec 2200S and 2120S controllers don't
recognize SCSI disks any more with the patch
commit 94cf6ba11b
Author: Salyzyn, Mark <mark_salyzyn@adaptec.com>
Date: Thu Dec 13 16:14:18 2007 -0800
[SCSI] aacraid: fix driver failure with Dell PowerEdge Expandable RAID Controller 3/Di
but fail with tons of "aac_srb: aac_fib_send failed with status: 8195"
instead. This patch disables the quirk introduced in the change cited
above for those two controllers again.
[thenzl: added 2120S Controller]
Signed-off-by: Gernot Hillier <gernot.hillier@siemens.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Cc: AACRAID list <aacraid@adaptec.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix setting of max_segment_size and seg_boundary mask for stacked md/dm
devices.
When stacking devices (LVM over MD over SCSI) some of the request queue
parameters are not set up correctly in some cases by default, namely
max_segment_size and and seg_boundary mask.
If you create MD device over SCSI, these attributes are zeroed.
Problem become when there is over this mapping next device-mapper mapping
- queue attributes are set in DM this way:
request_queue max_segment_size seg_boundary_mask
SCSI 65536 0xffffffff
MD RAID1 0 0
LVM 65536 -1 (64bit)
Unfortunately bio_add_page (resp. bio_phys_segments) calculates number of
physical segments according to these parameters.
During the generic_make_request() is segment cout recalculated and can
increase bio->bi_phys_segments count over the allowed limit. (After
bio_clone() in stack operation.)
Thi is specially problem in CCISS driver, where it produce OOPS here
BUG_ON(creq->nr_phys_segments > MAXSGENTRIES);
(MAXSEGENTRIES is 31 by default.)
Sometimes even this command is enough to cause oops:
dd iflag=direct if=/dev/<vg>/<lv> of=/dev/null bs=128000 count=10
This command generates bios with 250 sectors, allocated in 32 4k-pages
(last page uses only 1024 bytes).
For LVM layer, it allocates bio with 31 segments (still OK for CCISS),
unfortunatelly on lower layer it is recalculated to 32 segments and this
violates CCISS restriction and triggers BUG_ON().
The patch tries to fix it by:
* initializing attributes above in queue request constructor
blk_queue_make_request()
* make sure that blk_queue_stack_limits() inherits setting
(DM uses its own function to set the limits because it
blk_queue_stack_limits() was introduced later. It should probably switch
to use generic stack limit function too.)
* sets the default seg_boundary value in one place (blkdev.h)
* use this mask as default in DM (instead of -1, which differs in 64bit)
Bugs related to this:
https://bugzilla.redhat.com/show_bug.cgi?id=471639http://bugzilla.kernel.org/show_bug.cgi?id=8672
Signed-off-by: Milan Broz <mbroz@redhat.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
STM 2Gb flash is a large-page NAND flash. Set operations accordingly.
This field is dereferenced without a check in several places resulting in
OOPS.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Eric Miao <ymiao3@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The bnx2 chips do not support per MSI vector masking. On 5706/5708, new MSI
address/data are stored only when the MSI enable bit is toggled. As a result,
SMP affinity no longer works in the latest kernel. A more serious problem is
that the driver will no longer receive interrupts when the MSI receiving CPU
goes offline.
The workaround in this patch only addresses the problem of CPU going offline.
When that happens, the driver's timer function will detect that it is making
no forward progress on pending interrupt events and will recover from it.
Eric Dumazet reported the problem.
We also found that if an interrupt is internally asserted while MSI and INTA
are disabled, the chip will end up in the same state after MSI is re-enabled.
The same workaround is needed for this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Tested-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] hpwdt: Fix kdump when using hpwdt
[WATCHDOG] hpwdt: set the mapped BIOS address space as executable
[WATCHDOG] iTCO_wdt: add PCI ID's for ICH9 & ICH10 chipsets
[WATCHDOG] iTCO_wdt : correct status clearing
[WATCHDOG] iTCO_wdt : problem with rebooting on new ICH9 based motherboards
[WATCHDOG] fix mtx1_wdt compilation failure
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Update defconfigs for 2.6.28-rc7
macfb: Do not overflow fb_fix_screeninfo.id
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] stex: switch to block timeout
[SCSI] make scsi_eh_try_stu use block timeout
[SCSI] megaraid_sas: switch to block timeout
[SCSI] ibmvscsi: switch to block timeout
[SCSI] aacraid: switch to block timeout
[SCSI] zfcp: prevent double decrement on host_busy while being busy
[SCSI] zfcp: fix deadlock between wq triggered port scan and ERP
[SCSI] zfcp: eliminate race between validation and locking
[SCSI] zfcp: verify for correct rport state before scanning for SCSI devs
[SCSI] zfcp: returning an ERR_PTR where a NULL value is expected
[SCSI] zfcp: Fix opening of wka ports
[SCSI] zfcp: fix remote port status check
[SCSI] fc_transport: fix old bug on bitflag definitions
[SCSI] Fix hang in starved list processing
If xpc.ko and gru.ko are both statically linked into the kernel, then
xpc_init() can get called before gru_init() and make a call to one of the
gru's exported functions before the gru has initialized itself. The end
result is a NULL dereference.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We guarantee 400ns delay at the time of issuing the command.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also while at it:
* Drop unused arguments from ide_complete_power_step().
* Move DEBUG_PM printk() from ide_end_drive_cmd() to
ide_complete_power_step().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Respect current DMA setting during resume, otherwise PIO timings
may get destroyed if host uses shared PIO/MWDMA timings.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It seems that on some nVidia controllers using AltStatus register
can be unreliable so default to Status register if the PCI device
is in Compatibility Mode. In order to achieve this:
* Add ide_pci_is_in_compatibility_mode() inline helper to <linux/ide.h>.
* Add IDE_HFLAG_BROKEN_ALTSTATUS host flag and set it in amd74xx host
driver for nVidia controllers in Compatibility Mode.
* Teach actual_try_to_identify() and drive_is_ready() about the new flag.
This fixes the regression caused by removal of CONFIG_IDEPCI_SHARE_IRQ
config option in 2.6.25 and using AltStatus register unconditionally when
available (kernel.org bugs #11659 and #10216).
[ Moreover for CONFIG_IDEPCI_SHARE_IRQ=y (which is what most people
and distributions use) it never worked correctly. ]
Thanks to Remy LABENE and Lars Winterfeld for help with debugging the problem.
More info at:
http://bugzilla.kernel.org/show_bug.cgi?id=11659http://bugzilla.kernel.org/show_bug.cgi?id=10216
Reported-by: Remy LABENE <remy.labene@free.fr>
Tested-by: Remy LABENE <remy.labene@free.fr>
Tested-by: Lars Winterfeld <lars.winterfeld@tu-ilmenau.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't overflow the 16-character fb_fix_screeninfo id string (fixes some
console erasing and blanking artifacts). Have the ID default to "Unknown"
on machines with no built-in video and no nubus devices. Check for
fb_alloc_cmap failure.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
pci_get_device increments a reference count that should be decremented
using pci_dev_put.
The semantic patch that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S,S1;
position p1,p2,p3;
expression E,E1;
type T,T1;
expression *ptr != NULL;
@@
(
if ((x@p1 = pci_get_device(...)) == NULL) S
|
x@p1 = pci_get_device(...);
)
... when != pci_dev_put(...,(T)x,...)
when != if (...) { <+... pci_dev_put(...,(T)x,...) ...+> }
when != true x == NULL || ...
when != x = E
when != E = (T)x
when any
(
if (x == NULL || ...) S1
|
if@p2 (...) {
... when != pci_dev_put(...,(T1)x,...)
when != if (...) { <+... pci_dev_put(...,(T1)x,...) ...+> }
when != x = E1
when != E1 = (T1)x
(
return \(0\|<+...x...+>\|ptr\);
|
return@p3 ...;
)
}
)
@ script:python @
p1 << r.p1;
p3 << r.p3;
@@
print "* file: %s pci_get_device: %s return: %s" % (p1[0].file,p1[0].line,p3[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (25 commits)
em28xx: remove backward compat macro added on a previous fix
V4L/DVB (9748): em28xx: fix compile warning
V4L/DVB (9743): em28xx: fix oops audio
V4L/DVB (9742): em28xx-alsa: implement another locking schema
V4L/DVB (9732): sms1xxx: use new firmware for Hauppauge WinTV MiniStick
V4L/DVB (9691): gspca: Move the video device to a separate area.
V4L/DVB (9690): gspca: Lock the subdrivers via module_get/put.
V4L/DVB (9689): gspca: Memory leak when disconnect while streaming.
V4L/DVB (9668): em28xx: fix a race condition with hald
V4L/DVB (9664): af9015: don't reconnect device in USB-bus
V4L/DVB (9647): em28xx: void having two concurrent control URB's
V4L/DVB (9646): em28xx: avoid allocating/dealocating memory on every control urb
V4L/DVB (9645): em28xx: Avoid memory leaks if registration fails
V4L/DVB (9639): Make dib0700 remote control support work with firmware v1.20
V4L/DVB (9635): v4l: s2255drv fix firmware test on big-endian
V4L/DVB (9634): Make sure the i2c gate is open before powering down tuner
V4L/DVB (9632): make em28xx aux audio input work
V4L/DVB (9631): Make s2api work for ATSC support
V4L/DVB (9627): em28xx: Avoid i2c register error for boards without eeprom
V4L/DVB (9608): Fix section mismatch warning for dm1105 during make
...
drivers/gpu/drm/i915/i915_irq.c: In function 'i915_disable_pipestat':
drivers/gpu/drm/i915/i915_irq.c:101: warning: control may reach end of non-void function 'i915_pipestat' being inlined
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix module removal bugs of i82875p_edac. Also i82975x_edac code seems to
have the same module removal bugs as in i82875p_edac.
The problems were:
1. In module removal i82875p_remove_one() is never called.
Variable i82875p_registered is newer changed from 1, which
guarantees i82875p_remove_one() is not called (and even if it were
called, it would be called in wrong order).
As a result, the edac_mc workque is not stopped and keeps probing.
If kernel debugging options are not enabled, user may not notice
anything going wrong.
if debugging options are enabled and I do "rmmod i82875p_edac", I
get:
edac debug: edac_pci_workq_function() checking
BUG: unable to handle kernel paging request at f882d16f
...
call trace:
[<f8834df3>] ? edac_mc_workq_function+0x55/0x7e [edac_core]
[<c0233974>] ? run_workqueue+0xd7/0x1a5
[<c023392f>] ? run_workqueue+0x92/0x1a5
[<f8834d9e>] ? edac_mc_workq_function+0x0/0x7e [edac_core]
[<c0233af9>] ? worker_thread+0xb7/0xc3
[<c0236a7b>] ? autoremove_wake_function+0x0/0x33
[<c0233a42>] ? worker_thread+0x0/0xc3
[<c0236809>] ? kthread+0x3b/0x61
[<c02367ce>] ? kthread+0x0/0x61
[<c0204587>] ? kernel_thread_helper+0x7/0x10
Fix for this is to get rid of needles variable i82875p_registered
altogether and run i82875p_remove_one() *before*
pci_unregister_driver().
2. edac_mc_del_mc() uses mci after freeing mci
edac_mc_del_mc() calls calls edac_remove_sysfs_mci_device(). The
kobject refcount of mci drops to 0 and mci is freed. After this
mci is accessed via debug print and i82875p_remove_one() still
uses mci->pvt and tries to free mci again with edac_mc_free().
The fix for this is add kobject_get(&mci->edac_mci_kobj) after
edac_mc_alloc(). Then the mci is still available after returning
from edac_mc_del_mc() with refcount 1, and mci->pvt is still
available. When i82875p_remove_one() finally calls edac_mc_free(),
this will cause kobject_put() and mci is released properly.
Signed-off-by: Jarkko Lavinen <jlavi@iki.fi>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When I do "modprobe i82875p_edac" on my Asus P4C800 MB on kernels 2.6.26
or later, the module load fails due to BAR 0 collision. On 2.6.25 the
module loads just fine.
The overflow device on the MB seems to be hidden and its resources are not
allocated at normal PCI bus init. Log shows the missing resource problem:
EDAC DEBUG: i82875p_probe1()
PCI: 0000:00:06.0 reg 10 32bit mmio: [fecf0000, fecf0fff]
pci 0000:00:06.0: device not available because of BAR 0
[0xfecf0000-0xfecf0fff] collisions
EDAC i82875p: i82875p_setup_overfl_dev(): Failed to enable overflow
device
The patch below fixes this by calling pci_bus_assign_resources() after
the overflow device is revealed and added to the bus. With this patch
I am again able to load and use the module.
Signed-off-by: Jarkko Lavinen <jlavi@iki.fi>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit aef7db4bd5 fixed the problem with
recursive locking in fb blanking code if blank is caused by user setting
the /sys/class/graphics/fb*/blank. However this broke the fbcon timeout
blanking.
If you use a driver that defines ->fb_blank operation and at the same time
that driver relies on other driver (e.g. backlight or lcd class) to blank
the screen, when the fbcon times out and tries to blank the fb, it will
call only fb driver blanker and won't notify the other driver. Thus FB
output is disabled, but the screen isn't blanked.
Restore fbcon blanking and at the same time apply the proper fix for the
above problem: if fbcon_blank is called with FBINFO_FLAG_USEREVENT, we are
already called through notification from fb_blank, thus we don't have to
blank the fb again.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The engine on some radeon variants locks up if color expansion is called
for non aligned source data. This patch enables a feature of the core
fbdev to request aligned input pixmaps and uses the HW clipping engine to
clip the output to the requested size
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11875
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: James Cloos <cloos@jhcloos.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The spi master driver must have num_chipselect set to allow the bus to
initialise. Pass this through the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The spidev_to_sg() call in spi_s3c24xx_gpio.c was using the wrong method
to convert the spi device into the private data for the driver. Fix this
by using spi_master_get_devdata.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix unsafe order in dma mapping operation: always flush data from the
cache *BEFORE* invalidating it, to allow full duplex transfers where the
same buffer may be used for both writes and reads. Tested with mmc-spi.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the manual the "tdfOnExit" flag must be set on the last byte
we want to send. The PSC controller holds SS low until the flag is set.
However, the flag was set always on the last byte of the FIFO,
independently if it is the last byte of the transfer. This generates
spurious toggling of the SS signals that breaks the protocol of some
peripherals. Fix.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
make use of the new dmi device loading support to automatically load the
applesmc driver based on the dmi_match table.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The netmos_9xx5_combo type assumes that PCI SSID provides always the
correct value for the number of parallel and serial ports, but there are
indeed broken devices with wrong numbers, which may result in Oops.
This patch simply adds the check of the array range.
Reference: Novell bnc#447067
https://bugzilla.novell.com/show_bug.cgi?id=447067
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 50f3beb50a fixed em28xx-alsa
locking schema. However, a backport macro was kept.
This patch removes the macro, since it is not needed for the module
compilation against upstream.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: blacklist Seagate drives which time out FLUSH_CACHE when used with NCQ
[libata] pata_rb532_cf: fix signature of the xfer function
[libata] pata_rb532_cf: fix and rename register definitions
ata_piix: add borked Tecra M4 to broken suspend list
Replaced usb_kill_usb for usb_unlink_usb
(wait until urb to fully stop require USB core to put the calling process to sleep).
Oops:
http://www.kerneloops.org/raw.php?rawid=71799&msgid=
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Fix MTT leakage in resize CQ
IB/ehca: Fix problem with generated flush work completions
IB/ehca: Change misleading error message on memory hotplug
mlx4_core: Save/restore default port IB capability mask
Some recent Seagate harddrives have firmware bug which causes FLUSH
CACHE to timeout under certain circumstances if NCQ is being used.
This can be worked around by disabling NCQ and fixed by updating the
firmware. Implement ATA_HORKAGE_FIRMWARE_UPDATE and blacklist these
devices.
The wiki page has been updated to contain information on this issue.
http://ata.wiki.kernel.org/index.php/Known_issues
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Per definition, this function should return the number of bytes
consumed. As the original parameter "buflen" is being decremented inside
the read/write loop, save it in "retlen" at the beginning.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Sergei Shtyltov <sshtylyov@ru.mvista.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The original standalone driver uses a custom address for the error
register. Use it in pata_rb532_cf, too.
Rename two register definitions:
- The address offset 0x0800 in fact is the ATA base, not ATA command
address.
- The offset 0x0C00 is not a regular ATA data address, but a buffered one
allowing 4-byte IO.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tecra M4 sometimes forget what it is and reports bogus data via DMI
which makes the machine evade broken suspend matching and thus fail
suspend/resume. This patch updates piix_broken_suspend() such that it
can match such case. As the borked DMI data is a bit generic,
matching many entries to make the match more specific is necessary.
As the usual DMI matching is limited to four entries, this patch uses
hard coded manual matching.
This is reported by Alexandru Romanescu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When resizing a CQ, MTTs associated with the old CQE buffer were not
freed. As a result, if any app used resize CQ repeatedly, all MTTs
were eventually exhausted, which led to all memory registration
operations failing until the driver is reloaded.
Once the RESIZE_CQ command returns successfully from FW, FW no longer
accesses the old CQ buffer, so it is safe to deallocate the MTT
entries used by the old CQ buffer.
Finally, if the RESIZE_CQ command fails, the MTTs allocated for the
new CQEs buffer also need to be de-allocated.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1416>.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fix enables ehca device driver to generate flush work completions
even if the application doesn't request completions for all work
requests. The current implementation of ehca will generate flush work
completions for the wrong work requests if an application uses non
signaled work completions.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The error message printed when the eHCA driver prevents memory hotplug
is misleading -- the user might think that hot-removing the lhca,
hotplugging memory, then hot-adding the lhca again will work, but it
actually doesn't.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a number of sillies, from missing 'const' to using
'return' in void functions, to functions with no arguments not even
'void' and a cast which isn't required.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: sbp2: fix race condition in state change
ieee1394: fix list corruption (reported at module removal)
firewire: fw-sbp2: another iPod mini quirk entry
ieee1394: sbp2: another iPod mini quirk entry
stex sets the timeout in its slave configure routine for all devices.
This now needs to update the request queue timeout in block.
Cc: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_eh_try_stu() was still using the timeout parameter in the device
which is now not set (i.e. zero filled) meaning that it waited no time
at all for the start unit command to complete (leading the routine to
conclude failure every time). This lead to a 2.6.27 regression:
http://bugzilla.kernel.org/show_bug.cgi?id=12120
Where firewire devices that were non spec compliant wouldn't spin up.
Fix this by using the block queue timeout value instead.
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
megaraid_sas sets the timeout in its slave configure routine for devices
on special channels. This now needs to update the request queue timeout
in block.
Cc: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ibmvscsi sets the timeout in its slave configure routine for disk
devices. This now needs to update the request queue timeout in block.
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
aacraid updates the timeout in its slave configure routine if it is too
small. This now needs to update the request queue timeout in block.
Cc: AACRAID list <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Apple ALU wireless keyboards are bluetooth devices
HID: remove setup mutex, fix possible deadlock
HID: add USB ID for another dual gameron adapter
HID: unignore mouse on unibody macbooks
HID: fix blacklist entries for greenasia/pantherlord
We alloc a fake tty in usb serial console setup function. we should
init the tty's kref otherwise we will face WARN_ON after following
invoke of tty_port_tty_set --> tty_kref_get.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When no console is configured tty_open tries to call kref_get on a NULL
pointer, return ENODEV instead.
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The zfcp_scsi_queuecommand was not acting according to the standard
when the respective unit was not available. In this case an -EBUSY was
returned, which is not valid in itself, and in addition scsi_done
was called. This combination is not allowed and was leading to a
double finish of the request and therefor double decrement of the
host_busy counter.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Waiting for the ERP to be finished in a task running in the global
kernel work-queue is a bad idea, especially if the ERP needs to run
another job in this work-queue before it can finish. -> deadlock.
This patch removes the necessity to wait for a finished ERP from the
scan task and moves the job scheduling to the end of the ERP.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The check of having a valid pointer was performed before the
processing was secured by the lock. Between those two steps the
pointer can turn invalid. During further processing another value is
used (referenced by the pointer described above) as a function pointer
which is never verified to be valid either, resulting under some
circumstances in an invalid function call. This patch is fixing both
issues.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Prevent a SCSI target scan for a rport which have turned invalid
in the meantime.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Aborting a SCSI cmnd might requrie to send a abort_fsf_cmnd. If the
creation of this fsf_req fails an ERR_PTR is returned where a NULL
value would be expected as an error indicator. This ERR_PTR is
dereferenced as valid fsf_req in succeeding processing leading to
an error.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Running two wka_port_get calls in parallel could issue two open_port
requests, overwriting the port handle. Don't issue an open_port
for the state PORT_OPENING, and only read the data from GOOD
responses.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For an incoming RSCN it was checked by the ZFCP_STATUS_PORT_DID_DID
define to re-open a remote port or to test the connection. Since this
define was re-used it was also necessary to replace that define with
ZFCP_STATUS_PORT_PHYS_OPEN.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: serial: add more Onda device ids to option driver
USB: usb-storage: unusual_devs entry for Nikon D2H
USB: storage: unusual_devs entry for Mio C520-GPS
USB: fsl_usb2_udc: Report disconnect before unbinding
USB: fsl_qe_udc: Report disconnect before unbinding
USB: fix SB600 USB subsystem hang bug
Revert "USB: improve ehci_watchdog's side effect in CPU power management"
This reverts commit e669dae614, since it
is incomplete, and clashes with fuller patches and the sparc 32/64
unification effort.
Requested-by: David Miller <davem@davemloft.net>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the "hpwdt" module is loaded (even if the /dev/watchdog device is not
opened), then kdump does not work. The panic kernel either does not start at
all or crash in various places.
The problem is that hpwdt_pretimeout is registered with register_die_notifier()
with the highest possible priority. Because it returns NOTIFY_STOP, the
crash_nmi_callback which is also registered with register_die_notifier()
is never executed. This causes the shutdown of other CPUs to fail.
Reverting the order is no option: The crash_nmi_callback executes HLT
and so never returns normally. Because of that, it must be executed as
last notifier, which currently is done.
So, that patch returns NOTIFY_OK to keep the crash_nmi_callback executed.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
This patch adds an unusual_devs entry for the Nikon D2H camera.
From: Tobias Kunze Briseño <t@fictive.com>,
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1176) adds an unusual_devs entry for the Mio C520 GPS
unit. Other devices also based on the Mitac hardware use the same USB
interface firmware, so the Vendor and Product names are generalized.
This fixes Bugzilla #11583.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Tamas Kerecsen <kerecsen@bigfoot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Gadgets disable endpoints in their disconnect callbacks, so
we must call disconnect before unbinding. This also fixes
muram memory leak, since we free muram in the qe_ep_disable().
But mainly the patch fixes following badness:
root@b1:~# insmod fsl_qe_udc.ko
fsl_qe_udc: Freescale QE/CPM USB Device Controller driver, 1.0
fsl_qe_udc e01006c0.usb: QE USB controller initialized as device
root@b1:~# insmod g_ether.ko
g_ether gadget: using random self ethernet address
g_ether gadget: using random host ethernet address
usb0: MAC be:2d:3c:fa:be:f0
usb0: HOST MAC 62:b8:6a:df:38:66
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
fsl_qe_udc e01006c0.usb: fsl_qe_udc bind to driver g_ether
g_ether gadget: high speed config #1: CDC Ethernet (ECM)
root@b1:~# rmmod g_ether.ko
------------[ cut here ]------------
Badness at drivers/usb/gadget/composite.c:871
[...]
NIP [d10c1374] composite_unbind+0x24/0x15c [g_ether]
LR [d10a82f4] usb_gadget_unregister_driver+0x128/0x168 [fsl_qe_udc]
Call Trace:
[cfb93e80] [cfb1f3a0] 0xcfb1f3a0 (unreliable)
[cfb93eb0] [d10a82f4] usb_gadget_unregister_driver+0x128/0x168 [fsl_qe_udc]
[cfb93ed0] [d10c2a3c] usb_composite_unregister+0x3c/0x4c [g_ether]
[cfb93ee0] [c006bde0] sys_delete_module+0x130/0x19c
[cfb93f40] [c00142d8] ret_from_syscall+0x0/0x38
[...]
fsl_qe_udc e01006c0.usb: unregistered gadget driver 'g_ether'
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is required for all AMD SB600 revisions to avoid USB subsystem hang
symptom. The USB subsystem hang symptom is observed when the system has
multiple USB devices connected to it. In some cases a USB hub may be required
to observe this symptom.
Reported in bugzilla as #11599, the similar patch for SB700 old revision is:
commit b09bc6cbae
Reported-by: raffaele <ralfconn@tele2.it>
Tested-by: Roman Mamedov <roman@rm.pp.ru>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit f0d781d59c.
It was the wrong thing to do, and does not really do what it said
it did.
Cc: Yi Yang <yi.y.yang@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Fix copy'n'pasteo that broke VT switch if flushing was non-empty.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix system calls on Cell entered with XER.SO=1
powerpc/cell: Fix GDB watchpoints, again
powerpc/mpic: Don't reset affinity for secondary MPIC on boot
powerpc/cell/axon-msi: Retry on missing interrupt
powerpc: Fix boot freeze on machine with empty memory node
powerpc: Fix IRQ assignment for some PCIe devices
powerpc/spufs: Fix spinning in spufs_ps_fault on signal
powerpc/mpc832x_rdb: fix swapped ethernet ids
powerpc: Use generic PHY driver for Marvell 88E1111 PHY on GE Fanuc SBC610
powerpc/85xx: L2 cache size wrong in 8572DS dts
powerpc/virtex: Update defconfigs
powerpc/52xx: update defconfigs
xsysace: Fix driver to use resource_size_t instead of unsigned long
powerpc/virtex: fix various format/casting printk mismatches
powerpc/mpc5200: fix bestcomm Kconfig dependencies
powerpc/44x: Fix 460EX/460GT machine check handling
powerpc/40x: Limit allocable DRAM during early mapping
* master.kernel.org:/home/rmk/linux-2.6-arm:
Allow architectures to override copy_user_highpage()
[ARM] pxa/palmtx: misc fixes to use generic GPIO API
ARM: OMAP: Fixes for suspend / resume GPIO wake-up handling
[ARM] pxa/corgi: update default config to exclude tosa from being built
[ARM] pxa/pcm990: use negative number for an invalid GPIO in camera data
ARM: OMAP: Typo fix for clock_allow_idle
ARM: OMAP: Remove broken LCD driver for SX1
[ARM] 5335/1: pxa25x_udc: Fix is_vbus_present to return 1 or 0
[ARM] pxa/MioA701: bluetooth resume fix
[ARM] pxa/MioA701: fix memory corruption.
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Save/restore HWS_PGA on suspend/resume
drm: move drm vblank initialization/cleanup to driver load/unload
drm/i915: execbuffer pins objects, no need to ensure they're still in the GTT
drm/i915: Always read pipestat in irq_handler
drm/i915: Subtract total pinned bytes from available aperture size
drm/i915: Avoid BUG_ONs on VT switch with a wedged chipset.
drm/i915: Remove IMR masking during interrupt handler, and restart it if needed.
drm/i915: Manage PIPESTAT to control vblank interrupts instead of IMR.
