[ Upstream commit 0341d5e3d1 ]
The cur_tx counter must be incremented after TACT bit of
txdesc->status was set. However, a CPU is possible to reorder
instructions and/or memory accesses between cur_tx and
txdesc->status. And then, if TX interrupt happened at such a
timing, the sh_eth_tx_free() may free the descriptor wrongly.
So, add wmb() before cur_tx++.
Otherwise NETDEV WATCHDOG timeout is possible to happen.
Fixes: 86a74ff21a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdff1eda69 ]
One MIPS platform (mach-rc32434) defines GPIOBASE. This macro
conflicts with one of the same name in lpc_sch.c. Rename the latter one
to prevent the build error.
../drivers/mfd/lpc_sch.c:25: error: "GPIOBASE" redefined [-Werror]
25 | #define GPIOBASE 0x44
../arch/mips/include/asm/mach-rc32434/rb.h:32: note: this is the location of the previous definition
32 | #define GPIOBASE 0x050000
Cc: Denis Turischev <denis@compulab.co.il>
Fixes: e82c60ae7d ("mfd: Introduce lpc_sch for Intel SCH LPC bridge")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 922e8ce883 ]
The IRQ support for SCH GPIO is not specific to the Intel Quark SoC.
Moreover the IRQ routing is quite interesting there, so while it's
needs a special support, the driver haven't it anyway yet.
Due to above remove basically redundant code of IRQ support.
This reverts commit ec689a8a81.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b2b918319 ]
If error recovery is already enabled, bnxt_timer() will periodically
check the heartbeat register and the reset counter. If we get an
error recovery async. notification from the firmware (e.g. change in
primary/secondary role), we will immediately read and update the
heartbeat register and the reset counter. If the timer for the next
health check expires soon after this, we may read the heartbeat register
again in quick succession and find that it hasn't changed. This will
trigger error recovery unintentionally.
The likelihood is small because we also reset fw_health->tmr_counter
which will reset the interval for the next health check. But the
update is not protected and bnxt_timer() can miss the update and
perform the health check without waiting for the full interval.
Fix it by only reading the heartbeat register and reset counter in
bnxt_async_event_process() if error recovery is trasitioning to the
enabled state. Also add proper memory barriers so that when enabling
for the first time, bnxt_timer() will see the tmr_counter interval and
perform the health check after the full interval has elapsed.
Fixes: 7e914027f7 ("bnxt_en: Enable health monitoring.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4d95c3c19 ]
We currently only log the error recovery settings if it is enabled.
In some cases, firmware disables error recovery after it was
initially enabled. Without logging anything, the user will not be
aware of this change in setting.
Log it when error recovery is disabled. Also, change the reset count
value from hexadecimal to decimal.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 871127e6ab ]
Use the various netif_level() helpers to simplify the C code. This was
suggested by Joe Perches.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1611642024-3166-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5863b10aa8 ]
Combine the three netdev_warn() calls into a single call, printed at
the NETIF_MSG_HW log level.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a44daa8fcb ]
Firmware is capable of generating asynchronous debug notifications.
The event data is opaque to the driver and is simply logged. Debug
notifications can be enabled by turning on hardware status messages
using the ethtool msglvl interface.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fdab8a3ad ]
The current asic.rev is incomplete and does not include the metal
revision. Add the metal revision and decode the complete asic
revision into the more common and readable form (A0, B0, etc).
Fixes: 7154917a12 ("bnxt_en: Refactor bnxt_dl_info_get().")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1656db6723 ]
The FW_PSID version components are 8 bits wide, not 4.
Fixes: db28b6c77f ("bnxt_en: Fix devlink info's stored fw.psid version format.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63f8428b40 ]
Broadcom's b53 switches have one IMP (Inband Management Port) that needs
to be programmed using its own designed register. IMP port may be
different than CPU port - especially on devices with multiple CPU ports.
For that reason it's required to explicitly note IMP port index and
check for it when choosing a register to use.
This commit fixes BCM5301x support. Those switches use CPU port 5 while
their IMP port is 8. Before this patch b53 was trying to program port 5
with B53_PORT_OVERRIDE_CTRL instead of B53_GMII_PORT_OVERRIDE_CTRL(5).
It may be possible to also replace "cpu_port" usages with
dsa_is_cpu_port() but that is out of the scope of thix BCM5301x fix.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a0ed250f9 ]
The GRE tunnel device can pull existing outer headers in ipge_xmit.
This is a rare path, apparently unique to this device. The below
commit ensured that pulling does not move skb->data beyond csum_start.
But it has a false positive if ip_summed is not CHECKSUM_PARTIAL and
thus csum_start is irrelevant.
Refine to exclude this. At the same time simplify and strengthen the
test.
Simplify, by moving the check next to the offending pull, making it
more self documenting and removing an unnecessary branch from other
code paths.
Strengthen, by also ensuring that the transport header is correct and
therefore the inner headers will be after skb_reset_inner_headers.
The transport header is set to csum_start in skb_partial_csum_set.
Link: https://lore.kernel.org/netdev/YS+h%2FtqCJJiQei+W@shredder/
Fixes: 1d011c4803 ("ip_gre: add validation for csum_start")
Reported-by: Ido Schimmel <idosch@idosch.org>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ddbc2a00d ]
Previous commit 68233c583a removes the qlcnic_rom_lock()
in qlcnic_pinit_from_rom(), but remains its corresponding
unlock function, which is odd. I'm not very sure whether the
lock is missing, or the unlock is redundant. This bug is
suggested by a static analysis tool, please advise.
Fixes: 68233c583a ("qlcnic: updated reset sequence")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c5e6ff53 ]
syzbot found that forcing a big quantum attribute would crash hosts fast,
essentially using this:
tc qd replace dev eth0 root fq_codel quantum 4294967295
This is because fq_codel_dequeue() would have to loop
~2^31 times in :
if (flow->deficit <= 0) {
flow->deficit += q->quantum;
list_move_tail(&flow->flowchain, &q->old_flows);
goto begin;
}
SFQ max quantum is 2^19 (half a megabyte)
Lets adopt a max quantum of one megabyte for FQ_CODEL.
Fixes: 4b549a2ef4 ("fq_codel: Fair Queue Codel AQM")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 730affed24 ]
Bug reported by KASAN:
BUG: KASAN: use-after-scope in inet6_ehashfn (net/ipv6/inet6_hashtables.c:40)
Call Trace:
(...)
inet6_ehashfn (net/ipv6/inet6_hashtables.c:40)
(...)
nf_sk_lookup_slow_v6 (net/ipv6/netfilter/nf_socket_ipv6.c:91
net/ipv6/netfilter/nf_socket_ipv6.c:146)
It seems that this bug has already been fixed by Eric Dumazet in the
past in:
commit 78296c97ca ("netfilter: xt_socket: fix a stack corruption bug")
But a variant of the same issue has been introduced in
commit d64d80a2cd ("netfilter: x_tables: don't extract flow keys on early demuxed sks in socket match")
`daddr` and `saddr` potentially hold a reference to ipv6_var that is no
longer in scope when the call to `nf_socket_get_sock_v6` is made.
Fixes: d64d80a2cd ("netfilter: x_tables: don't extract flow keys on early demuxed sks in socket match")
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Benjamin Hesmans <benjamin.hesmans@tessares.net>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d12e1c4649 ]
Setting DSA_MAX_PORTS caused DSA to call b53 callbacks (e.g.
b53_disable_port() during dsa_register_switch()) for invalid
(non-existent) ports. That made b53 modify unrelated registers and is
one of reasons for a broken BCM5301x support.
This problem exists for years but DSA_MAX_PORTS usage has changed few
times. It seems the most accurate to reference commit dropping
dsa_switch_alloc() in the Fixes tag.
Fixes: 7e99e34701 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdb067d31c ]
It isn't true that CPU port is always the last one. Switches BCM5301x
have 9 ports (port 6 being inactive) and they use port 5 as CPU by
default (depending on design some other may be CPU ports too).
A more reliable way of determining number of ports is to check for the
last set bit in the "enabled_ports" bitfield.
This fixes b53 internal state, it will allow providing accurate info to
the DSA and is required to fix BCM5301x support.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecdc28defc ]
If the network devices connected to the system beyond
HSO_MAX_NET_DEVICES. add_net_device() in hso_create_net_device()
will be failed for the network_table is full. It will lead to
business failure which rely on network_table, for example,
hso_suspend() and hso_resume(). It will also lead to memory leak
because resource release process can not search the hso_device
object from network_table in hso_free_interface().
Add failure handler for add_net_device() in hso_create_net_device()
to solve the above problems.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfd862a7e9 ]
'$cin' and '$sin' variables are local to a function: they are then not
available from the cleanup trap.
Instead, we need to use '$large' and '$small' that are not local and
defined just before setting the trap.
Without this patch, running this script in a loop might cause a:
write: No space left on device
issue.
Fixes: 1a418cb8e8 ("mptcp: simult flow self-tests")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e90dfa7a8 ]
I noticed that only port 0 worked on the RTL8366RB since we
started to use custom tags.
It turns out that the format of egress custom tags is actually
different from ingress custom tags. While the lower bits just
contain the port number in ingress tags, egress tags need to
indicate destination port by setting the bit for the
corresponding port.
It was working on port 0 because port 0 added 0x00 as port
number in the lower bits, and if you do this the packet appears
at all ports, including the intended port. Ooops.
Fix this and all ports work again. Use the define for shifting
the "type A" into place while we're at it.
Tested on the D-Link DIR-685 by sending traffic to each of
the ports in turn. It works.
Fixes: 86dd9868b8 ("net: dsa: tag_rtl4_a: Support also egress tags")
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 889a1b3f35 ]
If an error occurs after a 'gpiochip_add_data()' call it must be undone by
a corresponding 'gpiochip_remove()' as already done in the remove function.
To simplify the code a fix a leak in the error handling path of the probe,
use the managed version instead (i.e. 'devm_gpiochip_add_data()')
Fixes: 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 555bda42b0 ]
Commit 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
has introduced a new 'goto err;' at the very end of the function, but has
not updated the error handling path accordingly.
Add the now missing 'irq_domain_remove()' call which balances a previous
'irq_domain_create_linear() call.
Fixes: 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edf7b4a2d8 ]
The build on fedora:35 and fedora:rawhide with clang is failing with:
49 41.00 fedora:35 : FAIL clang version 13.0.0 (Fedora 13.0.0~rc1-1.fc35)
bench/inject-buildid.c:351:6: error: variable 'len' set but not used [-Werror,-Wunused-but-set-variable]
u64 len = 0;
^
1 error generated.
make[3]: *** [/git/perf-5.14.0-rc7/tools/build/Makefile.build:139: bench] Error 2
50 41.11 fedora:rawhide : FAIL clang version 13.0.0 (Fedora 13.0.0~rc1-1.fc35)
bench/inject-buildid.c:351:6: error: variable 'len' set but not used [-Werror,-Wunused-but-set-variable]
u64 len = 0;
^
1 error generated.
make[3]: *** [/git/perf-5.14.0-rc7/tools/build/Makefile.build:139: bench] Error 2
That 'len' variable is not used at all, so just make sure all the
synthesize_RECORD() routines return ssize_t to propagate the writen()
return, as it may fail, ditch the 'ret' var and bail out if those
routines fail.
Fixes: 0bf02a0d80 ("perf bench: Add build-id injection benchmark")
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/CAM9d7cgEZNSor+B+7Y2C+QYGme_v5aH0Zn0RLfxoQ+Fy83EHrg@mail.gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b5ff0405e ]
0day bot reports a build error:
ERROR: modpost: "clear_user_page" [drivers/media/v4l2-core/videobuf-dma-sg.ko] undefined!
so export it in arch/arc/ to fix the build error.
In most ARCHes, clear_user_page() is a macro. OTOH, in a few
ARCHes it is a function and needs to be exported.
PowerPC exported it in 2004. It looks like nds32 and nios2
still need to have it exported.
Fixes: 4102b53392 ("ARC: [mm] Aliasing VIPT dcache support 2/4")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b430c7595 ]
A successful 'init_rs_non_canonical()' call should be balanced by a
corresponding 'free_rs()' call in the error handling path of the probe, as
already done in the remove function.
Update the error handling path accordingly.
Fixes: 8c61b7a7f4 ("[MTD] [NAND] Use rslib for CAFÉ ECC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/fd313d3fb787458bcc73189e349f481133a2cdc9.1629532640.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 817f9916a6 ]
The CONFIG_PCI=y case got a new parameter long time ago. Sync the stub as
well.
[bhelgaas: add parameter names]
Fixes: 725522b545 ("PCI: add the sysfs driver name to all modules")
Link: https://lore.kernel.org/r/20210813153619.89574-1-andriy.shevchenko@linux.intel.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6826c6849b ]
The CPU_ON PSCI call takes a payload that KVM uses to configure a
destination vCPU to run. This payload is non-architectural state and not
exposed through any existing UAPI. Effectively, we have a race between
CPU_ON and userspace saving/restoring a guest: if the target vCPU isn't
ran again before the VMM saves its state, the requested PC and context
ID are lost. When restored, the target vCPU will be runnable and start
executing at its old PC.
We can avoid this race by making sure the reset payload is serviced
before userspace can access a vCPU's state.
Fixes: 358b28f09f ("arm/arm64: KVM: Allow a VCPU to fully reset itself")
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210818202133.1106786-3-oupton@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6654f9dfcb ]
KVM correctly serializes writes to a vCPU's reset state, however since
we do not take the KVM lock on the read side it is entirely possible to
read state from two different reset requests.
Cure the race for now by taking the KVM lock when reading the
reset_state structure.
Fixes: 358b28f09f ("arm/arm64: KVM: Allow a VCPU to fully reset itself")
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210818202133.1106786-2-oupton@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a89d69a44e ]
Since 2431c4f5b4 ("mtd: Implement mtd_{read,write}() as wrappers
around mtd_{read,write}_oob()") don't allow _write|_read and
_write_oob|_read_oob existing at the same time, we should check the
existence of callbacks "_read and _write" from subdev's master device
(We can trust master device since it has been registered) before
assigning, otherwise following warning occurs while making
concatenated device:
WARNING: CPU: 2 PID: 6728 at drivers/mtd/mtdcore.c:595
add_mtd_device+0x7f/0x7b0
Fixes: 2431c4f5b4 ("mtd: Implement mtd_{read,write}() around ...")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210817114857.2784825-3-chengzhihao1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fe7c745f2 ]
Fixes a build error when CONFIG_HIST_TRIGGERS=n with boot-time
tracing. Since the trigger_process_regex() is defined only
when CONFIG_HIST_TRIGGERS=y, if it is disabled, the 'actions'
event option also must be disabled.
Link: https://lkml.kernel.org/r/162856123376.203126.582144262622247352.stgit@devnote2
Fixes: 81a59555ff ("tracing/boot: Add per-event settings")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a946506c48 ]
The driver was registering IRQ 0 when no IRQ was set. This leads to
warnings with newer kernels.
Clear the resource flags, so no resource is registered at all in this
case.
Fixes: 2f17dd34ff ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7eb6ea4148 ]
pci_dev_str_match_path() is often called with a spinlock held so the
allocation has to be atomic. The call tree is:
pci_specified_resource_alignment() <-- takes spin_lock();
pci_dev_str_match()
pci_dev_str_match_path()
Fixes: 45db33709c ("PCI: Allow specifying devices using a base bus and path of devfns")
Link: https://lore.kernel.org/r/20210812070004.GC31863@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e5df9571c ]
Even though ID_AA64MMFR0.PARANGE reports 52 bit PA size support, it cannot
be enabled as guest IPA size on 4K or 16K page size configurations. Hence
kvm_ipa_limit must be restricted to 48 bits. This change achieves required
IPA capping.
Before the commit c9b69a0cf0 ("KVM: arm64: Don't constrain maximum IPA
size based on host configuration"), the problem here would have been just
latent via PHYS_MASK_SHIFT (which earlier in turn capped kvm_ipa_limit),
which remains capped at 48 bits on 4K and 16K configs.
Cc: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Alexandru Elisei <alexandru.elisei@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: kvmarm@lists.cs.columbia.edu
Cc: linux-kernel@vger.kernel.org
Fixes: c9b69a0cf0 ("KVM: arm64: Don't constrain maximum IPA size based on host configuration")
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1628680275-16578-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3245a7b7b ]
Syzbot hit use-after-free in nf_tables_dump_sets. The problem was in
missing lock protection for nft_ct_pcpu_template_refcnt.
Before commit f102d66b33 ("netfilter: nf_tables: use dedicated
mutex to guard transactions") all transactions were serialized by global
mutex, but then global mutex was changed to local per netnamespace
commit_mutex.
This change causes use-after-free bug, when 2 netnamespaces concurently
changing nft_ct_pcpu_template_refcnt without proper locking. Fix it by
adding nft_ct_pcpu_mutex and protect all nft_ct_pcpu_template_refcnt
changes with it.
Fixes: f102d66b33 ("netfilter: nf_tables: use dedicated mutex to guard transactions")
Reported-and-tested-by: syzbot+649e339fa6658ee623d3@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2168e6bd7 ]
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of just
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aeaea8969b ]
In commit 7ef1c871da ("PCI: iproc: Use
pci_parse_request_of_pci_ranges()"), calling
devm_request_pci_bus_resources() was dropped from the common iProc
probe code, but is still needed for BCMA bus probing. Without it, there
will be lots of warnings like this:
pci 0000:00:00.0: BAR 8: no space for [mem size 0x00c00000]
pci 0000:00:00.0: BAR 8: failed to assign [mem size 0x00c00000]
Add back calling devm_request_pci_bus_resources() and adding the
resources to pci_host_bridge.windows for BCMA bus probe.
Link: https://lore.kernel.org/r/20210803215656.3803204-2-robh@kernel.org
Fixes: 7ef1c871da ("PCI: iproc: Use pci_parse_request_of_pci_ranges()")
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Cc: Roman Bacik <roman.bacik@broadcom.com>
Cc: Bharat Gooty <bharat.gooty@broadcom.com>
Cc: Abhishek Shah <abhishek.shah@broadcom.com>
Cc: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Cc: Ray Jui <ray.jui@broadcom.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: BCM Kernel Feedback <bcm-kernel-feedback-list@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: "Krzysztof Wilczyński" <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d277f6e88c ]
Commit 669cbc7081 ("PCI: Move DT resource setup into
devm_pci_alloc_host_bridge()") made devm_pci_alloc_host_bridge() fail on
any DT resource parsing errors, but Broadcom iProc uses
devm_pci_alloc_host_bridge() on BCMA bus devices that don't have DT
resources. In particular, there is no 'ranges' property. Fix iProc by
making 'ranges' optional.
If 'ranges' is required by a platform, there's going to be more errors
latter on if it is missing.
Link: https://lore.kernel.org/r/20210803215656.3803204-1-robh@kernel.org
Fixes: 669cbc7081 ("PCI: Move DT resource setup into devm_pci_alloc_host_bridge()")
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Cc: Roman Bacik <roman.bacik@broadcom.com>
Cc: Bharat Gooty <bharat.gooty@broadcom.com>
Cc: Abhishek Shah <abhishek.shah@broadcom.com>
Cc: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Cc: Ray Jui <ray.jui@broadcom.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: BCM Kernel Feedback <bcm-kernel-feedback-list@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit daa3736151 ]
Remove interrupt disablement during backlight setting. It is
way to dangerous and makes platforms instable by having it
miss vblank IRQs leading to the graphics derailing.
The code is using ndelay() which is not available on
platforms such as ARM and will result in 32 * udelay(1)
which is substantial.
Add some code to detect if an interrupt occurs during the
tight loop and in that case just redo it from the top.
Fixes: 5317f37e48 ("backlight: Add Kinetic KTD253 backlight driver")
Cc: Stephan Gerhold <stephan@gerhold.net>
Reported-by: newbyte@disroot.org
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f949a9ebce ]
On Cherry Trail devices with an AXP288 PMIC the external SD-card slot
used the AXP's DLDO2 as card-voltage and either DLDO3 or GPIO1LDO
(GPIO1 pin in low noise LDO mode) as signal-voltage.
These regulators are turned on/off and in case of the signal-voltage
also have their output-voltage changed by the _PS0 and _PS3 power-
management ACPI methods on the MMC-controllers ACPI fwnode as well as
by the _DSM ACPI method for changing the signal voltage.
The AML code implementing these methods is directly accessing the
PMIC through ACPI I2C OpRegion accesses, instead of using the special
PMIC OpRegion handled by drivers/acpi/pmic/intel_pmic_xpower.c .
This means that the contents of the involved PMIC registers can change
without the change being made through the regmap interface, so regmap
should not cache the contents of these registers.
Mark the regulator power on/off, the regulator voltage control and the
GPIO1 control registers as volatile, to avoid regmap caching them.
Specifically this fixes an issue on some models where the i915 driver
toggles another LDO using the same on/off register on/off through
MIPI sequences (through intel_soc_pmic_exec_mipi_pmic_seq_element())
which then writes back a cached on/off register-value where the
card-voltage is off causing the external sdcard slot to stop working
when the screen goes blank, or comes back on again.
The regulator register-range now marked volatile also includes the
buck regulator control registers. This is done on purpose these are
normally not touched by the AML code, but they are updated directly
by the SoC's PUNIT which means that they may also change without going
through regmap.
Note the AXP288 PMIC is only used on Bay- and Cherry-Trail platforms,
so even though this is an ACPI specific problem there is no need to
make the new volatile ranges conditional since these platforms always
use ACPI.
Fixes: dc91c3b6fe ("mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile")
Fixes: cd53216625 ("mfd: axp20x: Fix axp288 volatile ranges")
Reported-and-tested-by: Clamshell <clamfly@163.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1511df6f5e upstream.
EMIT6_PCREL() macro assumes that the previous pass generated 6 bytes
of code, which is not the case if branch shortening took place. Fix by
using jit->prg, like all the other EMIT6_PCREL_*() macros.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 4e9b4a6883 ("s390/bpf: Use relative long branches")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e61dc9da0 upstream.
The JIT uses agfi for subtracting constants, but -(-0x80000000) cannot
be represented as a 32-bit signed binary integer. Fix by using algfi in
this particular case.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 0546231057 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db7bee6538 upstream.
Currently the JIT completely removes things like `reg32 += 0`,
however, the BPF_ALU semantics requires the target register to be
zero-extended in such cases.
Fix by optimizing out only the arithmetic operation, but not the
subsequent zero-extension.
Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 0546231057 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0097ae5f7a ]
When the function IS_ALIGNED() returns false, the value of ret is 0.
So, we set ret to -EINVAL to indicate this error.
Clean up smatch warning:
drivers/ntb/test/ntb_perf.c:602 perf_setup_inbuf() warn: missing error
code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 319f83ac98 ]
When the value of nm->isr_ctx is false, the value of ret is 0.
So, we set ret to -ENOMEM to indicate this error.
Clean up smatch warning:
drivers/ntb/test/ntb_msi_test.c:373 ntb_msit_probe() warn: missing
error code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7db8263a12 ]
When adapter->registered_device_map is NULL, the value of err is
uncertain, we set err to -EINVAL to avoid ambiguity.
Clean up smatch warning:
drivers/net/ethernet/chelsio/cxgb/cxgb2.c:1114 init_one() warn: missing
error code 'err'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faa2e05ad0 ]
ebda_rsrc_controller() calls iounmap(io_mem) on the error path. Its caller,
ibmphp_access_ebda(), also calls iounmap(io_mem) on good and error paths.
Remove the iounmap(io_mem) invocation from ebda_rsrc_controller().
[bhelgaas: remove item from TODO]
Link: https://lore.kernel.org/r/20210818165751.591185-1-os.vaslot@gmail.com
Signed-off-by: Vishal Aslot <os.vaslot@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d52c58b9c ]
The function bfq_setup_merge prepares the merging between two
bfq_queues, say bfqq and new_bfqq. To this goal, it assigns
bfqq->new_bfqq = new_bfqq. Then, each time some I/O for bfqq arrives,
the process that generated that I/O is disassociated from bfqq and
associated with new_bfqq (merging is actually a redirection). In this
respect, bfq_setup_merge increases new_bfqq->ref in advance, adding
the number of processes that are expected to be associated with
new_bfqq.
Unfortunately, the stable-merging mechanism interferes with this
setup. After bfqq->new_bfqq has been set by bfq_setup_merge, and
before all the expected processes have been associated with
bfqq->new_bfqq, bfqq may happen to be stably merged with a different
queue than the current bfqq->new_bfqq. In this case, bfqq->new_bfqq
gets changed. So, some of the processes that have been already
accounted for in the ref counter of the previous new_bfqq will not be
associated with that queue. This creates an unbalance, because those
references will never be decremented.
This commit fixes this issue by reestablishing the previous, natural
behaviour: once bfqq->new_bfqq has been set, it will not be changed
until all expected redirections have occurred.
Signed-off-by: Davide Zini <davidezini2@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Link: https://lore.kernel.org/r/20210802141352.74353-2-paolo.valente@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aabbdc67f3 ]
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit LN920
0x1061 composition in order to avoid bind error.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
