commit 6c12a6384e upstream.
The queues assigned to a matrix mediated device are currently reset when:
* The VFIO_DEVICE_RESET ioctl is invoked
* The mdev fd is closed by userspace (QEMU)
* The mdev is removed from sysfs.
Immediately after the reset of a queue, a call is made to disable
interrupts for the queue. This is entirely unnecessary because the reset of
a queue disables interrupts, so this will be removed.
Furthermore, vfio_ap_irq_disable() does an unconditional PQAP/AQIC which
can result in a specification exception (when the corresponding facility
is not available), so this is actually a bugfix.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
[pasic@linux.ibm.com: minor rework before merging]
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Fixes: ec89b55e3b ("s390: ap: implement PAPQ AQIC interception in kernel")
Cc: <stable@vger.kernel.org>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f9c4845385 ]
ip_finish_output_gso() may call .ndo_features_check() even before the
skb has a L2 header. This conflicts with qeth_get_ip_version()'s attempt
to inspect the L2 header via vlan_eth_hdr().
Switch to vlan_get_protocol(), as already used further down in the
common qeth_features_check() path.
Fixes: f13ade1993 ("s390/qeth: run non-offload L3 traffic over common xmit path")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b41b554c1e ]
Due to insufficient locking, qeth_core_set_online() and
qeth_dev_layer2_store() can run in parallel, both attempting to load &
setup the discipline (and stepping on each other toes along the way).
A similar race can also occur between qeth_core_remove_device() and
qeth_dev_layer2_store().
Access to .discipline is meant to be protected by the discipline_mutex,
so add/expand the locking in qeth_core_remove_device() and
qeth_core_set_online().
Adjust the locking in qeth_l*_remove_device() accordingly, as it's now
handled by the callers in a consistent manner.
Based on an initial patch by Ursula Braun.
Fixes: 9dc48ccc68 ("qeth: serialize sysfs-triggered device configurations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0b9902c1fc ]
When qeth_dev_layer2_store() - holding the discipline_mutex - waits
inside qeth_l*_remove_device() for a qeth_do_reset() thread to complete,
we can hit a deadlock if qeth_do_reset() concurrently calls
qeth_set_online() and thus tries to aquire the discipline_mutex.
Move the discipline_mutex locking outside of qeth_set_online() and
qeth_set_offline(), and turn the discipline into a parameter so that
callers understand the dependency.
To fix the deadlock, we can now relax the locking:
As already established, qeth_l*_remove_device() waits for
qeth_do_reset() to complete. So qeth_do_reset() itself is under no risk
of having card->discipline ripped out while it's running, and thus
doesn't need to take the discipline_mutex.
Fixes: 9dc48ccc68 ("qeth: serialize sysfs-triggered device configurations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53a7f65583 upstream.
In dasd_alias_disconnect_device_from_lcu the device is removed from any
list on the LCU. Afterwards the LCU is removed from the lcu list if it
does not contain devices any longer.
The lcu->lock protects the lcu from parallel updates. But to cancel all
workers and wait for completion the lcu->lock has to be unlocked.
If two devices are removed in parallel and both are removed from the LCU
the first device that takes the lcu->lock again will delete the LCU because
it is already empty but the second device also tries to free the LCU which
leads to a list corruption of the lcu list.
Fix by removing the device right before the lcu is checked without
unlocking the lcu->lock in between.
Fixes: 8e09f21574 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ede91f83a upstream.
dasd_alias_add_device() moves devices to the active_devices list in case
of a scheduled LCU update regardless if they have previously been in a
pavgroup or not.
Example: device A and B are in the same pavgroup.
Device A has already been in a pavgroup and the private->pavgroup pointer
is set and points to a valid pavgroup. While going through dasd_add_device
it is moved from the pavgroup to the active_devices list.
In parallel device B might be removed from the same pavgroup in
remove_device_from_lcu() which in turn checks if the group is empty
and deletes it accordingly because device A has already been removed from
there.
When now device A enters remove_device_from_lcu() it is tried to remove it
from the pavgroup again because the pavgroup pointer is still set and again
the empty group will be cleaned up which leads to a list corruption.
Fix by setting private->pavgroup to NULL in dasd_add_device.
If the device has been the last device on the pavgroup an empty pavgroup
remains but this will be cleaned up by the scheduled lcu_update which
iterates over all existing pavgroups.
Fixes: 8e09f21574 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a29ea01653 upstream.
Prevent _lcu_update from adding a device to a pavgroup if the LCU still
requires an update. The data is not reliable any longer and in parallel
devices might have been moved on the lists already.
This might lead to list corruptions or invalid PAV grouping.
Only add devices to a pavgroup if the LCU is up to date. Additional steps
are taken by the scheduled lcu update.
Fixes: 8e09f21574 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 658a337a60 upstream.
For an LCU update a read unit address configuration IO is required.
This is started using sleep_on(), which has early exit paths in case the
device is not usable for IO. For example when it is in offline processing.
In those cases the LCU update should fail and not be retried.
Therefore lcu_update_work checks if EOPNOTSUPP is returned or not.
Commit 41995342b4 ("s390/dasd: fix endless loop after read unit address configuration")
accidentally removed the EOPNOTSUPP return code from
read_unit_address_configuration(), which in turn might lead to an endless
loop of the LCU update in offline processing.
Fix by returning EOPNOTSUPP again if the device is not able to perform the
request.
Fixes: 41995342b4 ("s390/dasd: fix endless loop after read unit address configuration")
Cc: stable@vger.kernel.org #5.3
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
and can subtrees.
Current release - regressions:
- gro_cells: reduce number of synchronize_net() calls
- ch_ktls: release a lock before jumping to an error path
Current release - always broken:
- tcp: Allow full IP tos/IPv6 tclass to be reflected in L3 header
Previous release - regressions:
- net/tls: fix missing received data after fast remote close
- vsock/virtio: discard packets only when socket is really closed
- sock: set sk_err to ee_errno on dequeue from errq
- cxgb4: fix the panic caused by non smac rewrite
Previous release - always broken:
- tcp: fix corner cases around setting ECN with BPF selection
of congestion control
- tcp: fix race condition when creating child sockets from
syncookies on loopback interface
- usbnet: ipheth: fix connectivity with iOS 14
- tun: honor IOCB_NOWAIT flag
- net/packet: fix packet receive on L3 devices without visible
hard header
- devlink: Make sure devlink instance and port are in same net
namespace
- net: openvswitch: fix TTL decrement action netlink message format
- bonding: wait for sysfs kobject destruction before freeing
struct slave
- net: stmmac: fix upstream patch applied to the wrong context
- bnxt_en: fix return value and unwind in probe error paths
Misc:
- devlink: add extra layer of categorization to the reload stats
uAPI before it's released
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=1tQm
-----END PGP SIGNATURE-----
Merge tag 'net-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.10-rc6, including fixes from the WiFi driver,
and CAN subtrees.
Current release - regressions:
- gro_cells: reduce number of synchronize_net() calls
- ch_ktls: release a lock before jumping to an error path
Current release - always broken:
- tcp: Allow full IP tos/IPv6 tclass to be reflected in L3 header
Previous release - regressions:
- net/tls: fix missing received data after fast remote close
- vsock/virtio: discard packets only when socket is really closed
- sock: set sk_err to ee_errno on dequeue from errq
- cxgb4: fix the panic caused by non smac rewrite
Previous release - always broken:
- tcp: fix corner cases around setting ECN with BPF selection of
congestion control
- tcp: fix race condition when creating child sockets from syncookies
on loopback interface
- usbnet: ipheth: fix connectivity with iOS 14
- tun: honor IOCB_NOWAIT flag
- net/packet: fix packet receive on L3 devices without visible hard
header
- devlink: Make sure devlink instance and port are in same net
namespace
- net: openvswitch: fix TTL decrement action netlink message format
- bonding: wait for sysfs kobject destruction before freeing struct
slave
- net: stmmac: fix upstream patch applied to the wrong context
- bnxt_en: fix return value and unwind in probe error paths
Misc:
- devlink: add extra layer of categorization to the reload stats uAPI
before it's released"
* tag 'net-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (68 commits)
sock: set sk_err to ee_errno on dequeue from errq
mptcp: fix NULL ptr dereference on bad MPJ
net: openvswitch: fix TTL decrement action netlink message format
can: af_can: can_rx_unregister(): remove WARN() statement from list operation sanity check
can: m_can: m_can_dev_setup(): add support for bosch mcan version 3.3.0
can: m_can: fix nominal bitiming tseg2 min for version >= 3.1
can: m_can: m_can_open(): remove IRQF_TRIGGER_FALLING from request_threaded_irq()'s flags
can: mcp251xfd: mcp251xfd_probe(): bail out if no IRQ was given
can: gs_usb: fix endianess problem with candleLight firmware
ch_ktls: lock is not freed
net/tls: Protect from calling tls_dev_del for TLS RX twice
devlink: Make sure devlink instance and port are in same net namespace
devlink: Hold rtnl lock while reading netdev attributes
ptp: clockmatrix: bug fix for idtcm_strverscmp
enetc: Let the hardware auto-advance the taprio base-time of 0
gro_cells: reduce number of synchronize_net() calls
net: stmmac: fix incorrect merge of patch upstream
ipv6: addrlabel: fix possible memory leak in ip6addrlbl_net_init
Documentation: netdev-FAQ: suggest how to post co-dependent series
ibmvnic: enhance resetting status check during module exit
...
When qeth_iqd_tx_complete() detects that a TX buffer requires additional
async completion via QAOB, it might fail to replace the queue entry's
metadata (and ends up triggering recovery).
Assume now that the device gets torn down, overruling the recovery.
If the QAOB notification then arrives before the tear down has
sufficiently progressed, the buffer state is changed to
QETH_QDIO_BUF_HANDLED_DELAYED by qeth_qdio_handle_aob().
The tear down code calls qeth_drain_output_queue(), where
qeth_cleanup_handled_pending() will then attempt to replace such a
buffer _again_. If it succeeds this time, the buffer ends up dangling in
its replacement's ->next_pending list ... where it will never be freed,
since there's no further call to qeth_cleanup_handled_pending().
But the second attempt isn't actually needed, we can simply leave the
buffer on the queue and re-use it after a potential recovery has
completed. The qeth_clear_output_buffer() in qeth_drain_output_queue()
will ensure that it's in a clean state again.
Fixes: 72861ae792 ("qeth: recovery through asynchronous delivery")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The two expected notification sequences are
1. TX_NOTIFY_PENDING with a subsequent TX_NOTIFY_DELAYED_*, when
our TX completion code first observed the pending TX and the QAOB
then completes at a later time; or
2. TX_NOTIFY_OK, when qeth_qdio_handle_aob() picked up the QAOB
completion before our TX completion code even noticed that the TX
was pending.
But as qeth_iqd_tx_complete() and qeth_qdio_handle_aob() can run
concurrently, we may end up with a race that results in a sequence of
TX_NOTIFY_DELAYED_* followed by TX_NOTIFY_PENDING. Which would confuse
the af_iucv code in its tracking of pending transmits.
Rework the notification code, so that qeth_qdio_handle_aob() defers its
notification if the TX completion code is still active.
Fixes: b333293058 ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Calling into socket code is ugly already, at least check whether we are
dealing with the expected sk_family. Only looking at skb->protocol is
bound to cause troubles (consider eg. af_packet).
Fixes: b333293058 ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove workaround that supported early hardware implementations
of PNSO OC3. Rely on the 'enarf' feature bit instead.
Fixes: fa115adff2 ("s390/qeth: Detect PNSO OC3 capability")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
[jwi: use logical instead of bit-wise AND]
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When requeueing all requests on the device request queue to the blocklayer
we might get to an ERP (error recovery) request that is a copy of an
original CQR.
Those requests do not have blocklayer request information or a pointer to
the dasd_queue set. When trying to access those data it will lead to a
null pointer dereference in dasd_requeue_all_requests().
Fix by checking if the request is an ERP request that can simply be
ignored. The blocklayer request will be requeued by the original CQR that
is on the device queue right behind the ERP request.
Fixes: 9487cfd343 ("s390/dasd: fix handling of internal requests")
Cc: <stable@vger.kernel.org> #4.16
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When both the paes and the pkey kernel module are statically build
into the kernel, the paes cipher selftests run before the pkey
kernel module is initialized. So a static variable set in the pkey
init function and used in the pkey_clr2protkey function is not
initialized when the paes cipher's selftests request to call pckmo for
transforming a clear key value into a protected key.
This patch moves the initial setup of the static variable into
the function pck_clr2protkey. So it's possible, to use the function
for transforming a clear to a protected key even before the pkey
init function has been called and the paes selftests may run
successful.
Reported-by: Alexander Egorenkov <Alexander.Egorenkov@ibm.com>
Cc: <stable@vger.kernel.org> # 4.20
Fixes: f822ad2c2c ("s390/pkey: move pckmo subfunction available checks away from module init")
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
With the last rework of the AP bus scan function one get_device() is
missing causing the reference counter to be one instance too
low. Together with binding/unbinding device drivers to an ap device it
may end up in an segfault because the ap device is freed but a device
driver still assumes it's pointer to the ap device is valid:
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 6b6b6b6b6b6b6000 TEID: 6b6b6b6b6b6b6803
Fault in home space mode while using kernel ASCE.
Krnl PSW : 0404e00180000000 000000001472f3b6 (klist_next+0x7e/0x180)
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3
Call Trace:
[<000000001472f3b6>] klist_next+0x7e/0x180
([<000000001472f36a>] klist_next+0x32/0x180)
[<00000000147c14de>] bus_for_each_dev+0x66/0xb8
[<0000000014aab0d4>] ap_scan_adapter+0xcc/0x6c0
[<0000000014aab74a>] ap_scan_bus+0x82/0x140
[<0000000013f3b654>] process_one_work+0x27c/0x478
[<0000000013f3b8b6>] worker_thread+0x66/0x368
[<0000000013f44e32>] kthread+0x17a/0x1a0
[<0000000014af23e4>] ret_from_fork+0x24/0x2c
Kernel panic - not syncing: Fatal exception: panic_on_oops
Fixed by adjusting the reference count with get_device() on the right
place. Also now the device drivers don't need to adjust the ap
device's reference counting any more. This is now done in the ap bus
probe and remove functions.
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Fixes: 4f2fcccdb5 ("s390/ap: add card/queue deconfig state")
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The system EID that is defined by the ISM driver is not correct. Using
an incorrect system EID allows to communicate with remote Linux systems
that use the same incorrect system EID, but when it comes to
interoperability with other operating systems then the system EIDs do
never match which prevents SMC-Dv2 communication.
Using the correct system EID fixes this problem.
Fixes: 201091ebb2 ("net/smc: introduce System Enterprise ID (SEID)")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Remove address space overrides using set_fs().
- Convert to generic vDSO.
- Convert to generic page table dumper.
- Add ARCH_HAS_DEBUG_WX support.
- Add leap seconds handling support.
- Add NVMe firmware-assisted kernel dump support.
- Extend NVMe boot support with memory clearing control and addition of
kernel parameters.
- AP bus and zcrypt api code rework. Add adapter configure/deconfigure
interface. Extend debug features. Add failure injection support.
- Add ECC secure private keys support.
- Add KASan support for running protected virtualization host with
4-level paging.
- Utilize destroy page ultravisor call to speed up secure guests shutdown.
- Implement ioremap_wc() and ioremap_prot() with MIO in PCI code.
- Various checksum improvements.
- Other small various fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl+JXIIACgkQjYWKoQLX
FBgIWAf9FKpnIsy/aNI2RpvojfySEhgH3T5zxGDTjghCSUQzAu0hIBPKhQOs/YfV
/apflXxNPneq7FsQPPpNqfdz2DXQrtgDfecK+7GyEVoOawFArgxiwP+tDVy4dmPT
30PNfr+BpGs7GjKuj33fC0c5U33HYvKzUGJn/GQB2Fhw+5tTDxxCubuS1GVR9iuw
/U1cQhG4KN0lwEeF2gO7BWWgqTH9C1t60+WzOQhIAbdvgtBRr1ctGu//F5S94BYL
NBw5Wxb9vUHrMm2mL0n8bi16hSn2MWHmAMQLkxPXI2osBYun3soaHUWFSA3ryFMw
4BGU+g7T66Pv3ZmLP4jH5UGrn8HWmg==
=4zdC
-----END PGP SIGNATURE-----
Merge tag 's390-5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Remove address space overrides using set_fs()
- Convert to generic vDSO
- Convert to generic page table dumper
- Add ARCH_HAS_DEBUG_WX support
- Add leap seconds handling support
- Add NVMe firmware-assisted kernel dump support
- Extend NVMe boot support with memory clearing control and addition of
kernel parameters
- AP bus and zcrypt api code rework. Add adapter configure/deconfigure
interface. Extend debug features. Add failure injection support
- Add ECC secure private keys support
- Add KASan support for running protected virtualization host with
4-level paging
- Utilize destroy page ultravisor call to speed up secure guests
shutdown
- Implement ioremap_wc() and ioremap_prot() with MIO in PCI code
- Various checksum improvements
- Other small various fixes and improvements all over the code
* tag 's390-5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (85 commits)
s390/uaccess: fix indentation
s390/uaccess: add default cases for __put_user_fn()/__get_user_fn()
s390/zcrypt: fix wrong format specifications
s390/kprobes: move insn_page to text segment
s390/sie: fix typo in SIGP code description
s390/lib: fix kernel doc for memcmp()
s390/zcrypt: Introduce Failure Injection feature
s390/zcrypt: move ap_msg param one level up the call chain
s390/ap/zcrypt: revisit ap and zcrypt error handling
s390/ap: Support AP card SCLP config and deconfig operations
s390/sclp: Add support for SCLP AP adapter config/deconfig
s390/ap: add card/queue deconfig state
s390/ap: add error response code field for ap queue devices
s390/ap: split ap queue state machine state from device state
s390/zcrypt: New config switch CONFIG_ZCRYPT_DEBUG
s390/zcrypt: introduce msg tracking in zcrypt functions
s390/startup: correct early pgm check info formatting
s390: remove orphaned extern variables declarations
s390/kasan: make sure int handler always run with DAT on
s390/ipl: add support to control memory clearing for nvme re-IPL
...
Merge more updates from Andrew Morton:
"155 patches.
Subsystems affected by this patch series: mm (dax, debug, thp,
readahead, page-poison, util, memory-hotplug, zram, cleanups), misc,
core-kernel, get_maintainer, MAINTAINERS, lib, bitops, checkpatch,
binfmt, ramfs, autofs, nilfs, rapidio, panic, relay, kgdb, ubsan,
romfs, and fault-injection"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (155 commits)
lib, uaccess: add failure injection to usercopy functions
lib, include/linux: add usercopy failure capability
ROMFS: support inode blocks calculation
ubsan: introduce CONFIG_UBSAN_LOCAL_BOUNDS for Clang
sched.h: drop in_ubsan field when UBSAN is in trap mode
scripts/gdb/tasks: add headers and improve spacing format
scripts/gdb/proc: add struct mount & struct super_block addr in lx-mounts command
kernel/relay.c: drop unneeded initialization
panic: dump registers on panic_on_warn
rapidio: fix the missed put_device() for rio_mport_add_riodev
rapidio: fix error handling path
nilfs2: fix some kernel-doc warnings for nilfs2
autofs: harden ioctl table
ramfs: fix nommu mmap with gaps in the page cache
mm: remove the now-unnecessary mmget_still_valid() hack
mm/gup: take mmap_lock in get_dump_page()
binfmt_elf, binfmt_elf_fdpic: use a VMA list snapshot
coredump: rework elf/elf_fdpic vma_dump_size() into common helper
coredump: refactor page range dumping into common helper
coredump: let dump_emit() bail out on short writes
...
We soon want to pass flags, e.g., to mark added System RAM resources.
mergeable. Prepare for that.
This patch is based on a similar patch by Oscar Salvador:
https://lkml.kernel.org/r/20190625075227.15193-3-osalvador@suse.de
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Juergen Gross <jgross@suse.com> # Xen related part
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Baoquan He <bhe@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: "Oliver O'Halloran" <oohall@gmail.com>
Cc: Pingfan Liu <kernelfans@gmail.com>
Cc: Nathan Lynch <nathanl@linux.ibm.com>
Cc: Libor Pechacek <lpechacek@suse.cz>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Leonardo Bras <leobras.c@gmail.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Julien Grall <julien@xen.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Yang <richardw.yang@linux.intel.com>
Link: https://lkml.kernel.org/r/20200911103459.10306-5-david@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add redirect_neigh() BPF packet redirect helper, allowing to limit stack
traversal in common container configs and improving TCP back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
Expand netlink policy support and improve policy export to user space.
(Ge)netlink core performs request validation according to declared
policies. Expand the expressiveness of those policies (min/max length
and bitmasks). Allow dumping policies for particular commands.
This is used for feature discovery by user space (instead of kernel
version parsing or trial and error).
Support IGMPv3/MLDv2 multicast listener discovery protocols in bridge.
Allow more than 255 IPv4 multicast interfaces.
Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
In Multi-patch TCP (MPTCP) support concurrent transmission of data
on multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
Support SMC-Dv2 version of SMC, which enables multi-subnet deployments.
Allow more calls to same peer in RxRPC.
Support two new Controller Area Network (CAN) protocols -
CAN-FD and ISO 15765-2:2016.
Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
Add TC actions for implementing MPLS L2 VPNs.
Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary notifications
and make it easier to offload nexthops into HW by converting
to a blocking notifier.
Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific
TCP option use.
Reorganize TCP congestion control (CC) initialization to simplify life
of TCP CC implemented in BPF.
Add support for shipping BPF programs with the kernel and loading them
early on boot via the User Mode Driver mechanism, hence reusing all the
user space infra we have.
Support sleepable BPF programs, initially targeting LSM and tracing.
Add bpf_d_path() helper for returning full path for given 'struct path'.
Make bpf_tail_call compatible with bpf-to-bpf calls.
Allow BPF programs to call map_update_elem on sockmaps.
Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
Support listing and getting information about bpf_links via the bpf
syscall.
Enhance kernel interfaces around NIC firmware update. Allow specifying
overwrite mask to control if settings etc. are reset during update;
report expected max time operation may take to users; support firmware
activation without machine reboot incl. limits of how much impact
reset may have (e.g. dropping link or not).
Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
Adopt or extend devlink use for debug, monitoring, fw update
in many drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw,
mv88e6xxx, dpaa2-eth).
In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
Add XDP support for Intel's igb driver.
Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
Improve performance for packets which don't require much offloads
on recent Mellanox NICs by 20% by making multiple packets share
a descriptor entry.
Move chelsio inline crypto drivers (for TLS and IPsec) from the crypto
subtree to drivers/net. Move MDIO drivers out of the phy directory.
Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=bc1U
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
This series consists of the usual driver updates (ufs, qla2xxx, tcmu,
ibmvfc, lpfc, smartpqi, hisi_sas, qedi, qedf, mpt3sas) and minor bug
fixes. There are only three core changes: adding sense codes,
cleaning up noretry and adding an option for limitless retries.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX4YulyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishaZDAQCT7rwG
UEZYHgYkU9EX9ERVBQM0SW4mLrxf3g3P5ioJsAEAtkclCM4QsIOP+MIPjIa0EyUY
khu0kcrmeFR2YwA8zhw=
=4w4S
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"The usual driver updates (ufs, qla2xxx, tcmu, ibmvfc, lpfc, smartpqi,
hisi_sas, qedi, qedf, mpt3sas) and minor bug fixes.
There are only three core changes: adding sense codes, cleaning up
noretry and adding an option for limitless retries"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (226 commits)
scsi: hisi_sas: Recover PHY state according to the status before reset
scsi: hisi_sas: Filter out new PHY up events during suspend
scsi: hisi_sas: Add device link between SCSI devices and hisi_hba
scsi: hisi_sas: Add check for methods _PS0 and _PR0
scsi: hisi_sas: Add controller runtime PM support for v3 hw
scsi: hisi_sas: Switch to new framework to support suspend and resume
scsi: hisi_sas: Use hisi_hba->cq_nvecs for calling calling synchronize_irq()
scsi: qedf: Remove redundant assignment to variable 'rc'
scsi: lpfc: Remove unneeded variable 'status' in lpfc_fcp_cpu_map_store()
scsi: snic: Convert to use DEFINE_SEQ_ATTRIBUTE macro
scsi: qla4xxx: Delete unneeded variable 'status' in qla4xxx_process_ddb_changed
scsi: sun_esp: Use module_platform_driver to simplify the code
scsi: sun3x_esp: Use module_platform_driver to simplify the code
scsi: sni_53c710: Use module_platform_driver to simplify the code
scsi: qlogicpti: Use module_platform_driver to simplify the code
scsi: mac_esp: Use module_platform_driver to simplify the code
scsi: jazz_esp: Use module_platform_driver to simplify the code
scsi: mvumi: Fix error return in mvumi_io_attach()
scsi: lpfc: Drop nodelist reference on error in lpfc_gen_req()
scsi: be2iscsi: Fix a theoretical leak in beiscsi_create_eqs()
...
-----BEGIN PGP SIGNATURE-----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=LzyE
-----END PGP SIGNATURE-----
Merge tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Series of merge handling cleanups (Baolin, Christoph)
- Series of blk-throttle fixes and cleanups (Baolin)
- Series cleaning up BDI, seperating the block device from the
backing_dev_info (Christoph)
- Removal of bdget() as a generic API (Christoph)
- Removal of blkdev_get() as a generic API (Christoph)
- Cleanup of is-partition checks (Christoph)
- Series reworking disk revalidation (Christoph)
- Series cleaning up bio flags (Christoph)
- bio crypt fixes (Eric)
- IO stats inflight tweak (Gabriel)
- blk-mq tags fixes (Hannes)
- Buffer invalidation fixes (Jan)
- Allow soft limits for zone append (Johannes)
- Shared tag set improvements (John, Kashyap)
- Allow IOPRIO_CLASS_RT for CAP_SYS_NICE (Khazhismel)
- DM no-wait support (Mike, Konstantin)
- Request allocation improvements (Ming)
- Allow md/dm/bcache to use IO stat helpers (Song)
- Series improving blk-iocost (Tejun)
- Various cleanups (Geert, Damien, Danny, Julia, Tetsuo, Tian, Wang,
Xianting, Yang, Yufen, yangerkun)
* tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block: (191 commits)
block: fix uapi blkzoned.h comments
blk-mq: move cancel of hctx->run_work to the front of blk_exit_queue
blk-mq: get rid of the dead flush handle code path
block: get rid of unnecessary local variable
block: fix comment and add lockdep assert
blk-mq: use helper function to test hw stopped
block: use helper function to test queue register
block: remove redundant mq check
block: invoke blk_mq_exit_sched no matter whether have .exit_sched
percpu_ref: don't refer to ref->data if it isn't allocated
block: ratelimit handle_bad_sector() message
blk-throttle: Re-use the throtl_set_slice_end()
blk-throttle: Open code __throtl_de/enqueue_tg()
blk-throttle: Move service tree validation out of the throtl_rb_first()
blk-throttle: Move the list operation after list validation
blk-throttle: Fix IO hang for a corner case
blk-throttle: Avoid tracking latency if low limit is invalid
blk-throttle: Avoid getting the current time if tg->last_finish_time is 0
blk-throttle: Remove a meaningless parameter for throtl_downgrade_state()
block: Remove redundant 'return' statement
...
Fixes 5 wrong format specification findings found by the
kernel test robot in ap_queue.c:
warning: format specifies type 'unsigned char' but the argument has type 'int' [-Wformat]
__func__, status.response_code,
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 2ea2a6099a ("s390/ap: add error response code field for ap queue devices")
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Introduce a way to specify additional debug flags with an crpyto
request to be able to trigger certain failures within the zcrypt
device drivers and/or ap core code.
This failure injection possibility is only enabled with a kernel debug
build CONFIG_ZCRYPT_DEBUG) and should never be available on a regular
kernel running in production environment.
Details:
* The ioctl(ICARSAMODEXPO) get's a struct ica_rsa_modexpo. If the
leftmost bit of the 32 bit unsigned int inputdatalength field is
set, the uppermost 16 bits are separated and used as debug flag
value. The process is checked to have the CAP_SYS_ADMIN capability
enabled or EPERM is returned.
* The ioctl(ICARSACRT) get's a struct ica_rsa_modexpo_crt. If the
leftmost bit of the 32 bit unsigned int inputdatalength field is set,
the uppermost 16 bits are separated and used als debug flag
value. The process is checked to have the CAP_SYS_ADMIN capability
enabled or EPERM is returned.
* The ioctl(ZSECSENDCPRB) used to send CCA CPRBs get's a struct
ica_xcRB. If the leftmost bit of the 32 bit unsigned int status
field is set, the uppermost 16 bits of this field are used as debug
flag value. The process is checked to have the CAP_SYS_ADMIN
capability enabled or EPERM is returned.
* The ioctl(ZSENDEP11CPRB) used to send EP11 CPRBs get's a struct
ep11_urb. If the leftmost bit of the 64 bit unsigned int req_len
field is set, the uppermost 16 bits of this field are used as debug
flag value. The process is checked to have the CAP_SYS_ADMIN
capability enabled or EPERM is returned.
So it is possible to send an additional 16 bit value to the zcrypt API
to be used to carry a failure injection command which may trigger
special behavior within the zcrypt API and layers below. This 16 bit
value is for the rest of the test referred as 'fi command' for Failure
Injection.
The lower 8 bits of the fi command construct a numerical argument in
the range of 1-255 and is the 'fi action' to be performed with the
request or the resulting reply:
* 0x00 (all requests): No failure injection action but flags may be
provided which may affect the processing of the request or reply.
* 0x01 (only CCA CPRBs): The CPRB's agent_ID field is set to
'FF'. This results in an reply code 0x90 (Transport-Protocol
Failure).
* 0x02 (only CCA CPRBs): After the APQN to send to has been chosen,
the domain field within the CPRB is overwritten with value 99 to
enforce an reply with RY 0x8A.
* 0x03 (all requests): At NQAP invocation the invalid qid value 0xFF00
is used causing an response code of 0x01 (AP queue not valid).
The upper 8 bits of the fi command may carry bit flags which may
influence the processing of an request or response:
* 0x01: No retry. If this bit is set, the usual loop in the zcrypt API
which retries an CPRB up to 10 times when the lower layers return
with EAGAIN is abandoned after the first attempt to send the CPRB.
* 0x02: Toggle special. Toggles the special bit on this request. This
should result in an reply code RY~0x41 and result in an ioctl
failure with errno EINVAL.
This failure injection possibilities may get some further extensions
in the future. As of now this is a starting point for Continuous Test
and Integration to trigger some failures and watch for the reaction of
the ap bus and zcrypt device driver code.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Move the creating and disposal of the struct ap_message one
level up the call chain. The ap message was constructed in the
calling functions in msgtype50 and msgtype6 but only for the
ica rsa messages. For CCA and EP11 CPRBs the ap message struct
is created in the zcrypt api functions.
This patch moves the construction of the ap message struct into
the functions zcrypt_rsa_modexpo and zcrypt_rsa_crt. So now all
the 4 zcrypt api functions zcrypt_rsa_modexpo, zcrypt_rsa_crt,
zcrypt_send_cprb and zcrypt_send_ep11_cprb appear and act
similar.
There are no functional changes coming with this patch.
However, the availability of the ap_message struct has
advantages which will be needed by a follow up patch.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Revisit the ap queue error handling: Based on discussions and
evaluatios with the firmware folk here is now a rework of the response
code handling for all the AP instructions. The idea is to distinguish
between failures because of some kind of invalid request where a retry
does not make any sense and a failure where another attempt to send
the very same request may succeed. The first case is handled by
returning EINVAL to the userspace application. The second case results
in retries within the zcrypt API controlled by a per message retry
counter.
Revisit the zcrpyt error handling: Similar here, based on discussions
with the firmware people here comes a rework of the handling of all
the reply codes. Main point here is that there are only very few
cases left, where a zcrypt device queue is switched to offline. It
should never be the case that an AP reply message is 'unknown' to the
device driver as it indicates a total mismatch between device driver
and crypto card firmware. In all other cases, the code distinguishes
between failure because of invalid message (see above - EINVAL) or
failures of the infrastructure (see above - EAGAIN).
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Support SCLP AP adapter config and deconfig operations:
The sysfs deconfig attribute /sys/devices/ap/cardxx/deconfig
for each AP card is now read-write. Writing in a '1' triggers
a synchronous SCLP request to configure the adapter, writing
in a '0' sends a synchronous SCLP deconfigure request.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Add support for AP bus adapter config and deconfig to the sclp
core code. The code is statically build into the kernel when
ZCRYPT is configured either as module or with static support.
This is the base functionality for having configure/deconfigure
support in the AP bus and card code. Another patch will exploit
this soon.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Suggested-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This patch adds a new config state to the ap card and queue
devices. This state reflects the response code
0x03 "AP deconfigured" on TQAP invocation and is tracked with
every ap bus scan.
Together with this new state now a card/queue device which
is 'deconfigured' is not disposed any more. However, for backward
compatibility the online state now needs to take this state into
account. So a card/queue is offline when the device is not configured.
Furthermore a device can't get switched from offline to online state
when not configured.
The config state is shown in sysfs at
/sys/devices/ap/cardxx/config
for the card and
/sys/devices/ap/cardxx/xx.yyyy/config
for each queue within each card.
It is a read-only attribute reflecting the negation of the
'AP deconfig' state as it is noted in the AP documents.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
On AP instruction failures the last response code is now
kept in the struct ap_queue. There is also a new sysfs
attribute showing this field (enabled only on debug kernels).
Also slight rework of the AP_DBF macros to get some more
content into one debug feature message line.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The state machine for each ap queue covered a mixture of
device states and state machine (firmware queue state) states.
This patch splits the device states and the state machine
states into two different enums and variables. The major
state is the device state with currently these values:
AP_DEV_STATE_UNINITIATED - fresh and virgin, not touched
AP_DEV_STATE_OPERATING - queue dev is working normal
AP_DEV_STATE_SHUTDOWN - remove/unbind/shutdown in progress
AP_DEV_STATE_ERROR - device is in error state
only when the device state is > UNINITIATED the state machine
is run. The state machine represents the states of the firmware
queue:
AP_SM_STATE_RESET_START - starting point, reset (RAPQ) ap queue
AP_SM_STATE_RESET_WAIT - reset triggered, waiting to be finished
if irqs enabled, set up irq (AQIC)
AP_SM_STATE_SETIRQ_WAIT - enable irq triggered, waiting to be
finished, then go to IDLE
AP_SM_STATE_IDLE - queue is operational but empty
AP_SM_STATE_WORKING - queue is operational, requests are stored
and replies may wait for getting fetched
AP_SM_STATE_QUEUE_FULL - firmware queue is full, so only replies
can get fetched
For debugging each ap queue shows a sysfs attribute 'states' which
displays the device and state machine state and is only available
when the kernel is build with CONFIG_ZCRYPT_DEBUG enabled.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Introduce a new internal struct zcrypt_track with an retry counter
field and a last return code field. Fill and update these fields at
certain points during processing of an request/reply. This tracking
info is then used to
- avoid trying to resend the message forever. Now each message is
tried to be send TRACK_AGAIN_MAX (currently 10) times and then the
ioctl returns to userspace with errno EAGAIN.
- avoid trying to resend the message on the very same card/domain. If
possible (more than one APQN with same quality) don't use the very
same qid as the previous attempt when again scheduling the request.
This is done by adding penalty weight values when the dispatching
takes place. There is a penalty TRACK_AGAIN_CARD_WEIGHT_PENALTY for
using the same card as previously and another penalty define
TRACK_AGAIN_QUEUE_WEIGHT_PENALTY to be considered when the same qid
as the previous sent attempt is calculated. Both values make it
harder to choose the very same card/domain but not impossible. For
example when only one APQN is available a resend can only address the
very same APQN.
There are some more ideas for the future to extend the use of this
tracking information. For example the last response code at NQAP and
DQAP could be stored there, giving the possibility to extended tracing
and debugging about requests failing to get processed properly.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/s390/net/ctcm_fsms.h: fsm_action_nop - only declaration left
after commit 04885948b1 ("ctc: removal of the old ctc driver")
drivers/s390/net/ctcm_mpc.h: ctcmpc_open - only declaration left after
commit 293d984f0e ("ctcm: infrastructure for replaced ctc driver")
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add/delete some blanks, white spaces and braces.
- Fix misindentations.
- Adjust a deprecated header include, and htons() conversion.
- Remove extra 'return' statements.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace our custom version of netdev_name().
Once we started to allocate the netdev at probe time with
commit d3d1b205e8 ("s390/qeth: allocate netdevice early"), this
stopped working as intended anyway.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The discipline struct is a fixed group of function pointers.
So declare the L2 and L3 disciplines as constant.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For OSA devices that are _not_ configured in prio-queue mode, give users
the option of selecting the number of active TX queues.
This requires setting up the HW queues with a reasonable default QoS
value in the QIB's PQUE parm area.
As with the other device types, we bring up the device with a minimal
number of TX queues for compatibility reasons.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a proper struct, and only program the QIB extensions for devices
where they are supported.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When re-initializing a device, we can hit a situation where
qeth_osa_set_output_queues() detects that it supports more or less
HW TX queues than before. Right now we adjust dev->real_num_tx_queues
from right there, but
1. it's getting more & more complicated to cover all cases, and
2. we can't re-enable the actually expected number of TX queues later
because we lost the needed information.
So keep track of the wanted TX queues (on initial setup, and whenever
its changed via .set_channels), and later use that information when
re-enabling the netdevice.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From the kernel perspective NVMe dump works exactly like zFCP dump.
Therefore, adapt all places where code explicitly tests only for
IPL of type FCP DUMP. And also set the memory end correctly in this case.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
arch/s390/pci/pci_bus.h: zpci_bus_init - only declaration left after
commit 05bc1be6db ("s390/pci: create zPCI bus")
arch/s390/include/asm/gmap.h: gmap_pte_notify - only declaration left
after commit 4be130a084 ("s390/mm: add shadow gmap support")
arch/s390/include/asm/pgalloc.h: rcu_table_freelist_finish - only
declaration left after commit 36409f6353 ("[S390] use generic RCU
page-table freeing code")
arch/s390/include/asm/tlbflush.h: smp_ptlb_all - only declaration left
after commit 5a79859ae0 ("s390: remove 31 bit support")
arch/s390/include/asm/vtimer.h: init_cpu_vtimer - only declaration left
after commit b5f87f15e2 ("s390/idle: consolidate idle functions and
definitions")
arch/s390/include/asm/pci.h: zpci_debug_info - only declaration left
after commit 386aa051fb ("s390/pci: remove per device debug attribute")
arch/s390/include/asm/vdso.h: vdso_alloc_boot_cpu - only declaration
left after commit 4bff8cb545 ("s390: convert to GENERIC_VDSO")
arch/s390/include/asm/smp.h: smp_vcpu_scheduled - only declaration left
after commit 67626fadd2 ("s390: enforce CONFIG_SMP")
arch/s390/kernel/entry.h: restart_call_handler - only declaration left
after commit 8b646bd759 ("[S390] rework smp code")
arch/s390/kernel/entry.h: startup_init_nobss - only declaration left
after commit 2e83e0eb85 ("s390: clean .bss before running uncompressed
kernel")
arch/s390/kernel/entry.h: s390_early_resume - only declaration left after
commit 394216275c ("s390: remove broken hibernate / power management
support")
drivers/s390/char/raw3270.h: raw3270_request_alloc_bootmem - only
declaration left after commit 33403dcfcd ("[S390] 3270 console:
convert from bootmem to slab")
drivers/s390/cio/device.h: ccw_device_schedule_sch_unregister - only
declaration left after commit 37de53bb52 ("[S390] cio: introduce ccw
device todos")
drivers/s390/char/tape.h: tape_hotplug_event - has only declaration
since recorded git history.
drivers/s390/char/tape.h: tape_oper_handler - has only declaration since
recorded git history.
drivers/s390/char/tape.h: tape_noper_handler - has only declaration
since recorded git history.
drivers/s390/char/tape_std.h: tape_std_check_locate - only declaration
left after commit 161beff8f4 ("s390/tape: remove tape block leftovers")
drivers/s390/char/tape_std.h: tape_std_default_handler - has only
declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_unexpect_uchk_handler - has only
declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_irq - has only declaration since
recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery - has only
declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery_has_failed -
has only declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery_succeded - has
only declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery_do_retry - has
only declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery_read_opposite -
has only declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery_HWBUG - has only
declaration since recorded git history.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
sclp_set_columns and sclp_set_htab are leftovers since commit 095761d28a
("[S390] sclp_tty: remove ioctl interface."), remove them as a dead code.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
sclp_sdias cannot be built as a module, CRASH_DUMP option is a bool not a
tristate. zcore_exit() has already been removed with commit cbe62fac17
("s390: char: make zcore explicitly non-modular"). Remove orphaned
sclp_sdias_exit for consistency as well.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
With SMCD version 2 the CHIDs of ISM devices are needed for the
CLC handshake.
This patch provides the new callback to retrieve the CHID of an
ISM device.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
