Do a cleanup in more headers:
- add forward declarations for types referenced by pointers
- add includes when types need them
This fixes potential compilation problems if the headers are reordered
or the missing includes are not provided indirectly.
Signed-off-by: David Sterba <dsterba@suse.com>
Patch series "New page table range API", v6.
This patchset changes the API used by the MM to set up page table entries.
The four APIs are:
set_ptes(mm, addr, ptep, pte, nr)
update_mmu_cache_range(vma, addr, ptep, nr)
flush_dcache_folio(folio)
flush_icache_pages(vma, page, nr)
flush_dcache_folio() isn't technically new, but no architecture
implemented it, so I've done that for them. The old APIs remain around
but are mostly implemented by calling the new interfaces.
The new APIs are based around setting up N page table entries at once.
The N entries belong to the same PMD, the same folio and the same VMA, so
ptep++ is a legitimate operation, and locking is taken care of for you.
Some architectures can do a better job of it than just a loop, but I have
hesitated to make too deep a change to architectures I don't understand
well.
One thing I have changed in every architecture is that PG_arch_1 is now a
per-folio bit instead of a per-page bit when used for dcache clean/dirty
tracking. This was something that would have to happen eventually, and it
makes sense to do it now rather than iterate over every page involved in a
cache flush and figure out if it needs to happen.
The point of all this is better performance, and Fengwei Yin has measured
improvement on x86. I suspect you'll see improvement on your architecture
too. Try the new will-it-scale test mentioned here:
https://lore.kernel.org/linux-mm/20230206140639.538867-5-fengwei.yin@intel.com/
You'll need to run it on an XFS filesystem and have
CONFIG_TRANSPARENT_HUGEPAGE set.
This patchset is the basis for much of the anonymous large folio work
being done by Ryan, so it's received quite a lot of testing over the last
few months.
This patch (of 38):
Determine if a value lies within a range more efficiently (subtraction +
comparison vs two comparisons and an AND). It also has useful (under some
circumstances) behaviour if the range exceeds the maximum value of the
type. Convert all the conflicting definitions of in_range() within the
kernel; some can use the generic definition while others need their own
definition.
Link: https://lkml.kernel.org/r/20230802151406.3735276-1-willy@infradead.org
Link: https://lkml.kernel.org/r/20230802151406.3735276-2-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
bitmap_test_range_all_{set,zero} defined in subpage.c are useful for other
components. Move them to misc.h and use them in zoned.c. Also, as
find_next{,_zero}_bit take/return "unsigned long" instead of "unsigned
int", convert the type to "unsigned long".
While at it, also rewrite the "if (...) return true; else return false;"
pattern and add const to the input bitmap.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The div_factor* helpers calculate fraction or percentage fraction. The
name is a bit confusing, we use it only for percentage calculations and
there are two helpers.
There's a helper mult_frac that's for general fractions, that tries to
be accurate but we multiply and divide by small numbers so we can use
the div_u64 helper.
Rename the div_factor* helpers and use 1..100 percentage range, also drop
the case checking for percentage == 100, it's never hit.
The conversions:
* div_factor calculates tenths and the numbers need to be adjusted
* div_factor_fine is direct replacement
Signed-off-by: David Sterba <dsterba@suse.com>
Define helper macro that can be used in enum {} to utilize the automatic
increment to define all bits without directly defining the values or
using additional linear bits.
1. capture the sequence value, N
2. use the value to define the given enum with N-th bit set
3. reset the sequence back to N
Use for enums that do not require fixed values for symbolic names (like
for on-disk structures):
enum {
ENUM_BIT(FIRST),
ENUM_BIT(SECOND),
ENUM_BIT(THIRD)
};
Where the values would be 0x1, 0x2 and 0x4.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We still have this oddity of stashing the io_failure_record in the
extent state for the io_failure_tree, which is leftover from when we
used to stuff private pointers in extent_io_trees.
However this doesn't make a lot of sense for the io failure records, we
can simply use a normal rb_tree for this. This will allow us to further
simplify the extent_io_tree code by removing the io_failure_rec pointer
from the extent state.
Convert the io_failure_tree to an rb tree + spinlock in the inode, and
then use our rb tree simple helpers to insert and find failed records.
This greatly cleans up this code and makes it easier to separate out the
extent_io_tree code.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
asm/do_div.h is for div_u64, but it is found in math64.h. This change
will make compiler job easier and prevent compiler errors in situation
where compiler will not find math64.h from another paths.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Structure tree_entry provides a very simple rb_tree which only uses
bytenr as search index.
That tree_entry is used in 3 structures: backref_node, mapping_node and
tree_block.
Since we're going to make backref_node independnt from relocation, it's
a good time to extract the tree_entry into rb_simple_node, and export it
into misc.h.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
As is_power_of_two takes unsigned long, it's not safe on 32bit
architectures, but we could pass any u64 value in seveal places. Add a
separate helper and also an alias that better expresses the purpose for
which the helper is used.
Signed-off-by: David Sterba <dsterba@suse.com>
The file ctree.h serves as a header for everything and has become quite
bloated. Split some helpers that are generic and create a new file that
should be the catch-all for code that's not btrfs-specific.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
