When scanning for the broadcast SSID, there is no need to add the
SSID TLV (restoring the behaviour of the driver behaviour in the wext
days, confirmed in Marvell specifications).
If bssid is unspecified, the current scan code will usually fire off an
active scan probing for the specific requested SSID. However, if a scan
is ongoing (or has just finished), those scan results will be used
instead (even if that scan is totally different, e.g. a passive scan on
channel 4 for a different SSID). Fix this inconsistency by always
firing off a scan when associating without a bssid.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TSF can be kept per vif.
Add ieee80211_vif param to set/get/reset_tsf, and move
the debugfs entries to the per-vif directory.
Update all the drivers that implement these callbacks.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this represents the bitmap of block ACK received after the
successful transmission of an aggregate frame. also made few
changes to beautify the display
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most boards with SysKonnect/Marvell Ethernet have only a single port.
For the single port case, use the standard Ethernet driver convention
of allocating IRQ when device is brought up rather than at probe time.
This patch also adds some additional read after writes to avoid any
PCI posting problems when setting the IRQ mask.
The error handling of dual port cards is also changed. If second port
can not be brought up, then just fail. No point in continuing, since
the failure is most certainly because of out of memory.
It is worth noting that the dual port skge device has a single irq but two
seperate status rings and therefore has two NAPI objects, one for
each port.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix provides a newly flashed FW version (appended, in braces)
along with the currently running FW version via ethtool. The newly
flashed version runs only after a system reset.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-posting with subject fixed!
Multicast programming has been broken since commit 5b8821b7. Setting the
MULTICAST flag while sending the cmd to the FW was missing. Fixed this.
Also fixed-up some indentation in the adjacent lines.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch touchs most of the enic port profile handling code.
Tried to break it into sub patches without success.
The patch mainly does the following:
- Port profile operations for a SRIOV VF are modified to work
only via its PF
- Changes the port profile static struct in struct enic to a pointer.
This is because a SRIOV PF has to now hold the port profile information
for all its VF's
- Moved address registration for VF's during port profile ASSOCIATE time
- Most changes in port profile handling code are changes related to indexing
into the port profile struct array of a PF for the VF port profile
information
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds helper functions to use PF as proxy for SRIOV VF firmware
commands.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to enable SRIOV on enic devices. Enic SRIOV VF's are dynamic vnics and will use the same driver code as dynamic vnics.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most sky2 hardware only has a single port, although some variations of the
chip support two interfaces. For the single port case, use the standard
Ethernet driver convention of allocating IRQ when device is brought up
rather than at probe time.
Also, change the error handling of dual port cards so that if second
port can not be brought up, then just fail. No point in continuing, since
the failure is most certainly because of out of memory.
The dual port sky2 device has a single irq and a single status ring,
therefore it has a single NAPI object shared by both ports.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev is unused in pch_gbe_setup_rctl. Remove this declaration to
avoid a compiler warning.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ehea ndo_get_stats can sleep in two places, in a hcall
and in a GFP_KERNEL alloc, which is not correct.
This patch creates a delayed workqueue that grabs the information each 1
sec from the hardware, and place it into the device structure, so that,
.ndo_get_stats quickly returns the device structure statistics block.
Signed-off-by: Breno Leitao <brenohl@br.ibm.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds one step support to the phyter. When enabled, the
hardware does not provide time stamps for transmitted sync messages but
instead inserts the stamp into the outgoing packet.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables six external event channels and one periodic output.
One GPIO is reserved for synchronizing multiple PHYs. The assignment
of GPIO functions can be changed via a module parameter.
The code supports multiple simultaneous events by inducing a PTP clock
event for every channel marked in the PHY's extended status word.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
proper dma_unmapping and freeing of skb's has to be done in the rx
cleanup for EDMA chipsets when the device is unloaded and this also
seems to address the following warning which shows up occasionally when
the device is unloaded
Call Trace:
[<c0148cd2>] warn_slowpath_common+0x72/0xa0
[<c03b669c>] ? dma_debug_device_change+0x19c/0x200
[<c03b669c>] ? dma_debug_device_change+0x19c/0x200
[<c0148da3>] warn_slowpath_fmt+0x33/0x40
[<c03b669c>] dma_debug_device_change+0x19c/0x200
[<c0657f12>] notifier_call_chain+0x82/0xb0
[<c0171370>] __blocking_notifier_call_chain+0x60/0x90
[<c01713bf>] blocking_notifier_call_chain+0x1f/0x30
[<c044f594>] __device_release_driver+0xa4/0xc0
[<c044f647>] driver_detach+0x97/0xa0
[<c044e65c>] bus_remove_driver+0x6c/0xe0
[<c029af0b>] ? sysfs_addrm_finish+0x4b/0x60
[<c0450109>] driver_unregister+0x49/0x80
[<c0299f54>] ? sysfs_remove_file+0x14/0x20
[<c03c3ab2>] pci_unregister_driver+0x32/0x80
[<f92c2162>] ath_pci_exit+0x12/0x20 [ath9k]
[<f92c8467>] ath9k_exit+0x17/0x36 [ath9k]
[<c06523cd>] ? mutex_unlock+0xd/0x10
[<c018e27f>] sys_delete_module+0x13f/0x200
[<c02139bb>] ? sys_munmap+0x4b/0x60
[<c06547c5>] ? restore_all+0xf/0xf
[<c0657a20>] ? spurious_fault+0xe0/0xe0
[<c01832f4>] ? trace_hardirqs_on_caller+0xf4/0x180
[<c065b863>] sysenter_do_call+0x12/0x38
---[ end trace 16e1c1521c06bcf9 ]---
Mapped at:
[<c03b7938>] debug_dma_map_page+0x48/0x120
[<f92ba3e8>] ath_rx_init+0x3f8/0x4b0 [ath9k]
[<f92b5ae4>] ath9k_init_device+0x4c4/0x7b0 [ath9k]
[<f92c2813>] ath_pci_probe+0x263/0x330 [ath9k]
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver rtl8192cu assigns a new struct rtl_tcb_desc object, but fails to
clear it.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [2.6.39+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If iwl_scan_initiate() fails for any reason,
priv->scan_request and priv->scan_vif are left
dangling. This can lead to a crash later when
iwl_bg_scan_completed() tries to run a pending
scan request.
In practice, this seems to be very rare due to
the STATUS_SCANNING check earlier. That check,
however, is wrong -- it should allow a scan to
be queued when a reset/roc scan is going on.
When a normal scan is already going on, a new
one can't be issued by mac80211, so that code
can be removed completely. I introduced this
bug when adding off-channel support in commit
266af4c745.
Cc: stable@kernel.org [3.0]
Reported-by: Peng Yan <peng.yan@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Argument list to CDRP function has become unmanageably long. Fix it by properly
declaring a struct that encompasses all the input and output parameters.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ameen Rahman <ameen.rahman@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The imx6q enet is a derivative of imx28 enet controller. It fixed
the frame endian issue found on imx28, and added 1 Gbps support.
It also fixes a typo on vendor name in Kconfig.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function fec_enet_mii_init(), it uses non-zero pdev->id as part
of the condition to check the second fec instance (fec1). This works
before the driver supports device tree probe. But in case of device
tree probe, pdev->id is -1 which is also non-zero, so the logic becomes
broken when device tree probe gets supported.
The patch change the logic to check "pdev->id > 0" as the part of the
condition for identifying fec1.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
FEC can work without a phy reset on some platforms, which means not
very platform necessarily have a phy-reset gpio encoded in device tree.
Even on the platforms that have the gpio, FEC can work without
resetting phy for some cases, e.g. boot loader has done that.
So it makes more sense to have the phy-reset-gpio request failure as
a debug message rather than a warning, and get fec_reset_phy() return
void since the caller does not check the return anyway.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finish conversion to unified ethtool ops: convert get_flags.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SEEQ drivers should depend on HAS_IOMEM to prevent compile breakage
on !HAS_IOMEM architectures:
drivers/net/ethernet/seeq/seeq8005.c: In function 'seeq8005_probe1':
drivers/net/ethernet/seeq/seeq8005.c:179:2: error:
implicit declaration of function 'inw' [-Werror=implicit-function-declaration]
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reloading FW during resets can cause issues. Remove the full reset
as it is not needed.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for WOL as determined by the EEPROM.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to avoid a hardware lockup when Tx work is still
pending and we request a reset.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for configuring the priority to
traffic class mapping.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need SFP+ plugable support for X540 hardware (copper only) so
don't enable the SFP+ interrupts.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The DCB CEE command set_state() will complete successfully
but is misleading because it enables IEEE mode. After
this patch the command is failed.
And IEEE PFC/ETS is managed from ieee paths now instead
of using CEE primitives.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the PCI device flag indicating if a VF is assigned to a guest VM
to guard against destroying VFs upon driver removal. Implement
additional feature to detect if VFs already exist when the driver
is loaded and if so configure them and set the driver state to
SR-IOV enabled.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the AP_MAX_LINKS as the upper boundary for traversing the links array,
thereby guaranteeing BA sessions with all connected STAs are stopped when
the stop_ba event is received.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Fix an erroneous labeling of array boundaries in the fw_status structure.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Save the configured bitrate, and use the min allowed rate
as the basic rate (e.g. when scanning).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If a hidden SSID is requested, generate a probe response template
containing the real SSID.
Depends on the patch "mac80211: add ssid config to bss information
in AP-mode".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On roaming, the auth and assoc req are sent with the sta
hlid. This is wrong, as the sta hlid is configured according
to the old ap. Use the dev_hlid instead.
Move the wl1271_tx_update_filters() call into wl1271_tx_get_hlid(),
so wl->dev_hlid will be valid.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
There is a race condition between wl1271_tx_work() and the
channel switch, so make sure all the pending packets are
being sent before switching channel.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx uses a single probe response template, regardless of
the probe request.
However, the P2P spec forbids including the p2p ie in some
cases (e.g. the probe request didn't include the p2p ie).
The fw responds only to probe requests that don't
include the p2p ie, and passes up probe requests that
include them (the supplicant will answer them).
Thus, strip the p2p ie from the probe response template.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx uses the beacon as the probe response template.
However, the beacon includes a TIM ie, which shouldn't
exist in the probe response.
Delete it from the skb before configuring the probe
response template.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We were including only 11b rates in IBSS mode. This patch adds OFDM
rates.
[Rephrased commit log and removed one unnecessary comment. -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Due to some changes in PM in recent kernels, the sdio_test module has
been broken for a while. This patch fixes the code that powers the
card on and off.
Also made some small indentation fixes in the Makefile.
[Rephrased commit log and removed the change in the FW name, since
it's done in another patch. -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: David Dillow <dave@thedillows.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Alexander Indenbaum <baum@tehutinetworks.net>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Steve Hodgson <shodgson@solarflare.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using incorrect max and min dwell times during forced passive
scans because we were still using the active scan states to scan
(passively) the channels that were not marked as passive.
Instead of doing passive scans in active states, we now skip active
states and scan for all channels in passive states.
Cc: <stable@kernel.org> # 2.6.36+
Signed-off-by: Luciano Coelho <coelho@ti.com>
- fix features : jumbo frames and checksumming can not be used at the
same time.
- introduce hw_jumbo_{enable / disable} helpers. Their content has been
creatively extracted from Realtek's own drivers. As an illustration,
it would be nice to know how/if the MaxTxPacketSize register operates
when the device can work with a 9k jumbo frame as its documentation
(8168c) can not be applied beyond ~7k.
- rtl_tx_performance_tweak is moved forward. No change.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
8168d and above allow jumbo frames beyond 8k. Bump the received
packet length check before enabling jumbo frames on these chipsets.
Frame length indication covers bits 0..13 of the first Rx descriptor
32 bits for the 8169 and 8168. I only have authoritative documentation
for the allowed use of the extra (13) bit with the 8169 and 8168c.
Realtek's drivers use the same mask for the 816x and the fast ethernet
only 810x.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
For RTL8111EVL, the register of MaxTxPacketSize doesn't acctually
limit the tx size. It influnces the feature of early tx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
If register_netdev() fails now, then we call mutex_unlock(&bnad->conf_mutex);
on the error path, but it's already unlocked. So we acquire the lock in error
path which will be later unlocked after the cleanup.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We dereference "rate" on the lines before so the checks here are too
late to help. This function is only called from
mwifiex_dump_station_info() and "rate" is always a non-NULL pointer
so the check can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're not likely to hit this small memory leak, but lets fix it
anyway to keep the static checkers happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_trans_rx_alloc is only called from iwl_rx_init, so no need
to init the lists twice.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During my works on the transport layer I removed code that updated
a local variable (is_agg) that is needed to keep the pending_frames
count up to date. Fix this.
Also, there should be no way to have a packet with TX_CTL_AMPDU set
while the internal aggregation state machine is not in AGG_ON state.
Add a WARN_ON to ensure that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has been removed but the declaration hasn't.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This simplifies both the transport layer and the upper layer.
Kill the union in the device command, which avoids the funny syntax
we had: cmd->cmd.payload.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before this patch, the upper layer could register a callback for each
host command. This mechanism allowed the upper layer to have
different callbacks for the same command ID. In fact, it wasn't used
and the rx_handlers is enough: same callback for all the command with
a specific command ID.
The iwl_send_add_station needs the access the command that was sent
while handling the response (regardless if the command was sent in
SYNC or ASYNC mode). So now, all the handlers receive the host
command that was sent. This implies a change in the handler signature.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we're associated and want to do P2P at the same
time, the scan for remain-on-channel is currently
limited to 80ms because of the way the device will
behave in that case. Instead of doing that, split
up the dwell times into little pieces. It will not
actually be a single big dwell time then, but will
be close enough. This improves robustness of P2P
in such scenarios.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the driver split there's no more need for
shared/non-shared private station data so remove
struct iwl_station_priv_common entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the driver split there's no longer a need
to have the scan code scattered across multiple
files, so move it all back to iwl-scan.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlegacy version of fix:
commit effd4d9aec
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Sep 15 11:46:52 2011 -0700
iwlagn: do not use interruptible waits
Since the dawn of its time, iwlwifi has used
interruptible waits to wait for synchronous
commands and firmware loading.
This leads to "interesting" bugs, because it
can't actually handle the interruptions; for
example when a command sending is interrupted
it will assume the command completed fully,
and then leave it pending, which leads to all
kinds of trouble when the command finishes
later.
Since there's no easy way to gracefully deal
with interruptions, fix the driver to not use
interruptible waits.
This at least fixes the error
iwlagn 0000:02:00.0: Error: Response NULL in 'REPLY_SCAN_ABORT_CMD'
I have seen in P2P testing, but it is likely
that there are other errors caused by this.
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlegacy version of fix:
commit 282cdb325a
Author: Johannes Berg <johannes.berg@intel.com>
Date: Mon Sep 12 12:09:10 2011 -0700
iwlagn: fix command queue timeout
If the command queue is constantly busy,
which can happen in P2P, the hangcheck
timer will frequently find a command in
it and will eventually reset the device
because nothing sets the timestamp for
this queue when commands are processed.
Fix this by setting the timestamp when
a command completes.
iwlegacy does not support P2P, but this patch fix possible
unneeded hardware resets, hence is needed.
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During the endurance testing, rx frames are not getting DMAd from
MAC whereas pcu rx frame counters are getting updated properly.
As per systems team input updated the initval to fix rx dma stuck
issue.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We check ether_type before registering the platform device in
arch/m68k/mac/config.c. Doing the same test again in the driver is
redundant so remove it.
Multiple probes should not happen since the conversion to platform devices,
so lose that test too.
Then macmace.c need not include macintosh.h, so remove that and irq.h and
include linux/interrupt.h explicitly.
Tested on PowerBook 520, Quadra 660av, LC 630.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMSC911X_USE_16BIT needs to be set when using 16-bit register
access. However, currently no flag is set if the device tree
doesn't specify 32-bit access, resulting in a BUG() and a non-
working driver when 16-bit register access is configured for
smsc911x in the DT.
This patch should set the SMSC911X_USE_16BIT flag in a manner
consistent with the documented DT bindings.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the peak_pci driver for the PCAN PCI/PCIe cards (1, 2, 3
or 4 channels) from PEAK Systems (http://www.peak-system.com).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that at least one PPC machine would occasionally give a (valid) 0 as
the return value from dma_map, this caused the ixgbe code to not work
correctly. A fix is pending in the PPC tree to not return 0 from dma map, but
we can also fix the driver to make sure we don't mess up in other arches as
well.
This patch is applicable to all current stable kernels.
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=683611
Reported-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: stable@kernel.org
Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 92cd3a17ce
tg3: Simplify tx bd assignments
broke VLAN tagging on outbound packets.
It ifdef'ed BCM_KERNEL_SUPPORTS_8021Q, but this
is not set anywhere. So vlan never gets set, and
all packets are sent with vlan=0.
v2: We can just remove the test. vlan_tx_tag_present
is valid regardless of whether the 802.1q module
is built.
Tested on BCM5721 rev 11.
Signed-off-by: Kasper Pedersen <kernel@kasperkp.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the IC+ IP101A Single port 10/100 PHY
and supports the APS (i.e. power saving mode while link is down)
for both IP1001 and IP101A (where this mode is supported).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a6b7a40786 removed
linux/interrupt.h from netdevice.h. This fixes below build failure
drivers/net/pxa168_eth.c: In function 'pxa168_eth_collect_events':
drivers/net/pxa168_eth.c:866: error: 'IRQ_NONE' undeclared (first use in this function)
drivers/net/pxa168_eth.c:866: error: (Each undeclared identifier is reported only once
drivers/net/pxa168_eth.c:866: error: for each function it appears in.)
drivers/net/pxa168_eth.c: At top level:
drivers/net/pxa168_eth.c:913: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'pxa168_eth_int_handler'
drivers/net/pxa168_eth.c: In function 'pxa168_eth_open':
drivers/net/pxa168_eth.c:1133: error: implicit declaration of function 'request_irq'
drivers/net/pxa168_eth.c:1133: error: 'pxa168_eth_int_handler' undeclared (first use in this function)
drivers/net/pxa168_eth.c:1134: error: 'IRQF_DISABLED' undeclared (first use in this function)
drivers/net/pxa168_eth.c:1160: error: implicit declaration of function 'free_irq'
Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 88491d8(drivers/net: Kconfig & Makefile cleanup) causes a
regression that netconsole does not work if netconsole and network
device driver are build into kernel, because netconsole is linked
before network device driver.
Andrew Morton suggested to fix this with initcall ordering.
Fixes it by switching init_netconsole() to late_initcall.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function may currently fill one entry beyond the end of the
array it is given. It also doesn't return an error code in case
it does detect overflow.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using MLPPP, the maximum size of a fragment is incorrectly
calculated with an offset of -2.
This patch reverses the changes in the patch found here:
http://marc.info/?l=linux-netdev&m=123541324010539&w=2
The value of hdrlen includes the size of both the 2-byte PPP protocol
field and the 2- or 4-byte multilink header (2+4=6 for long sequence
numbers, 2+2=4 for short sequence numbers). Section 2 of RFC1661 says
that the MRU that is negotiated (i.e., the MTU of the sending system)
includes only the PPP payload but not the protocol field, thus the
correct MTU should be the link's MTU minus the multilink header (mtu -
(hdrlen-2)).
The incorrect calculation causes Linux to fragment packets to a size two
bytes smaller than the allowed MTU. While not technically illegal, this
behaviour confounds MRU-tuning to avoid PPP-layer fragmentation.
Signed-off-by: Henry Wong <henry@stuffedcow.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GRETH GBIT core does not do checksum offloading for IP
segmentation. This patch adds a check in the xmit function to
determine if the stack has calculated the checksum for us.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o A performance drop was seen with firmware loaded
from flash. This workaround fixes it.
o Updated driver version to 4.0.77
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three drivers, rtl8192ce, rtl8192cu and rtl8192de, use the same macro
to check if a particular rate is in the CCK set. This common code is
relocated to a common header file. A distinct macro used by rtl8192se
with the same name is renamed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The various modparam messages are difficult to understand.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The various modparam messages are difficult to understand.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The various modparam messages are difficult to understand.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CCK/OFDM noise immunilty values are always reset to defaults
during bgscan. This could affect the link quality and
performance when the STA is associated in a noisy channel.
So do not override the learned values across the scanning.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit d1b08284 use new frag API but would leave f to be used
uninitialized, this patch fix it.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using the multi_tx_table to map possible Tx queues to Tx rings
we can just do simple subtraction for the unlikely event that the Tx queue
provided exceeds the number of Tx rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since igb only uses advanced descriptors we might as well just use an IGB
specific define and drop the _ADV suffix for the descriptor declarations.
In addition this can be further reduced by assuming that it will be working
on pointers since that is normally how the Tx descriptors are handled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many of the function names in the hot path are carrying an extra "_adv"
suffix on the end of them to represent the fact that they are using
advanced descriptors instead of legacy descriptors. However since all igb
uses are advanced descriptors adding the extra suffix doesn't really add
any additional data. Since this is the case it is easiest to just drop the
suffix and save us from having to store the extra characters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to be a general cleanup and performance improvement
for clean_rx_irq. The previous patch should have updated the allocation so
that the rings can be treated as read-only within the clean_rx_irq
function. In addition I am re-ordering the operations such that several
goals are accomplished including reducing the overhead for packet
accounting, reducing the number of items on the stack, and improving
overall performance.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to improve performance by splitting the Tx and Rx
rings into 3 sections. The first is primarily a read only section
containing basic things like the indexes, a pointer to the dev and netdev
structures, and basic information. The second section contains the stats
and next_to_use and next_to_clean values. The third section is primarily
unused values that can just be placed at the end of the ring and are not
used in the hot path.
The adapter structure has several sections that are read in the hot path.
In order to improve performance there I am combining the frequent read
hot path items into a single cache line.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to streamline the Rx buffer allocation and cleanup.
This is accomplished by reducing the number of writes by only having the Rx
descriptor ring written by software during allocation, and it will only be
read during cleanup.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change removes support for single buffer mode from igb and makes the
driver function in packet split always. The advantage to doing this is
that we can reduce total memory allocation overhead significantly as we
will only need to allocate one 1K slab per packet and then make use of a
reusable half page instead of allocating a 2K slab per packet.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the max_frame_size in order account for an optional
VLAN tag. In order to support this we must also increase the
MAX_STD_JUMBO_FRAME_SIZE to account for the 4 extra bytes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up the RXDCTL and TXDCTL configurations and optimizes RX
performance by allowing back write-backs on all hardware other than 82576.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
They have been taken from brcmsmac, add Broadcom's copyright.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
re-apply the unsigned shorts bug fixed by Dan Carpenter but get lost
after the file move.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Same stack corruption problem as temperature offset
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the dawn of its time, iwlwifi has used
interruptible waits to wait for synchronous
commands and firmware loading.
This leads to "interesting" bugs, because it
can't actually handle the interruptions; for
example when a command sending is interrupted
it will assume the command completed fully,
and then leave it pending, which leads to all
kinds of trouble when the command finishes
later.
Since there's no easy way to gracefully deal
with interruptions, fix the driver to not use
interruptible waits.
This at least fixes the error
iwlagn 0000:02:00.0: Error: Response NULL in 'REPLY_SCAN_ABORT_CMD'
I have seen in P2P testing, but it is likely
that there are other errors caused by this.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: stable@kernel.org [2.6.24+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For retrieve calibration hdr related information, instead of using structure in
one place and #define in other place, unify the method to use data structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 2000 series of NICs, version 2 of temperature offset calibration
should be used.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the removal of the sysfs files, it is no
longer necessary to have upper layers control
the drvdata, so let the PCI driver have it for
itself completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug_level and temperature files should be in
debugfs, the txpower file is completely unneeded
since TX power can be set with iw/iwconfig.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_suspend and iwl_resume don't exist.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's nothing PCI(E) specific in this file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The transport callbacks might as well be undefined
when CONFIG_PM_SLEEP is not set, so ifdef all of
it out and make everything available for PM_SLEEP
only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to have the transport layer have a
callback for iwl_trans_send_cmd_pdu() since it is
just a generic wrapper around iwl_trans_send_cmd().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all the PCI-E specific transport files to
be iwl-trans-pcie*; specifically iwl-trans.c
which is really iwl-trans-pcie.c.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After driver split and no need to support legacy devices, there is no reason
we need to separate the NVM access into different files, merge those.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
From time to time, we hit a WARN_ON in iwl_mac_remove_interface.
This basically means that we got out of sync with mac80211: the vif
we hold differs from the vif 80211 passes as parameter. Try to get
some data that will help to debug this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All devices use the same value for beacon_time_tsf_bits. Use the #define
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
chain_noise_num_beacons is set and never changes. Use the #define
rather than 3 levels of indirection.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The modinfo report for 135 ucode is iwlwifi-135-IWL135_UCODE_API_MAX.ucode
Change to show the value of the define: iwlwifi-135-6.ucode
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding another SKU for 6005 series devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert kzalloc to kcalloc, coalesce multiple lines too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and do a few clean up fixes on the way
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add documentation to the bus layer API - iwl-bus.h
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enum iwl_rxon_context_id is the right type to use when we need a
rxon_context_id.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a wrapper in the upper layer to call the mac80211's function.
This allows not to have the transport layer call mac80211 directly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a non-empty Tx queueis freed, the buffer it contains must be
freed too. Since the Tx cmd are now allocated from a pool, the Tx
cmd must be freed too.
This patch avoids to destroy a non-empty pool of Tx cmd.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the driver is unloaded while there is still a host command in
flight, its tfd will be freed by iwl_tx_queue_free.
This function is called for both types of queues: Tx queues and cmd
queue. This didn't take in count the fact that in Tx queues, tfds are
mapped as TO_DEVICE (besides the first TB), whereas in cmd queue, all
TBs are mapped as BIDI.
Hence, tx_queue_free unmapped the second (and higher) TB of each tfd
in the cmd queue as TO_DEVICE, whereas they must be freed as BIDI.
This means that if a multi TFD is in flight while we unload the
driver (which is quite unlikely but can happen), we will get the
warning below.
This patch fixes this.
[ 445.234060] ------------[ cut here ]------------
[ 445.236273] WARNING: at lib/dma-debug.c:861 check_unmap+0x337/0x780()
[ 445.236654] iwlagn 0000:02:00.0: DMA-API: device driver frees DMA memory with different direction [device address=0x0000000126950540] [size=8 bytes] [mapped with DMA_BIDIRECTIONAL] [unmapped with DMA_TO_DEVICE]
[ 445.236654] Modules linked in: ...
[ 445.236654] Pid: 1415, comm: modprobe Not tainted 3.1.0-rc4-wl-65912-g5215ff1-dirty #79
[ 445.236654] Call Trace:
[ 445.236654] [<ffffffff81043a51>] warn_slowpath_common+0x71/0xa0
[ 445.236654] [<ffffffff81043b37>] warn_slowpath_fmt+0x47/0x50
[ 445.236654] [<ffffffff8121e687>] check_unmap+0x337/0x780
[ 445.236654] [<ffffffff810e9136>] ? free_one_page+0x156/0x320
[ 445.236654] [<ffffffff8121ec5a>] debug_dma_unmap_page+0x5a/0x60
[ 445.236654] [<ffffffffa021d701>] iwlagn_unmap_tfd.isra.11+0x121/0x1c0 [iwlagn]
[ 445.236654] [<ffffffffa021ddf2>] iwlagn_txq_free_tfd+0x42/0x70 [iwlagn]
[ 445.236654] [<ffffffffa02121de>] iwl_tx_queue_unmap+0x4e/0x70 [iwlagn]
[ 445.236654] [<ffffffffa0212fad>] iwl_trans_pcie_tx_free+0x10d/0x440 [iwlagn]
[ 445.236654] [<ffffffff81064959>] ? destroy_workqueue+0xb9/0x1e0
[ 445.236654] [<ffffffffa021330a>] iwl_trans_pcie_free+0x2a/0x2c0 [iwlagn]
[ 445.236654] [<ffffffffa022f4f2>] iwl_remove+0x149/0x17e [iwlagn]
[ 445.236654] [<ffffffffa022f546>] iwl_pci_remove+0x1f/0x65 [iwlagn]
[ 445.236654] [<ffffffff81228337>] pci_device_remove+0x47/0x120
[ 445.236654] [<ffffffff8134566c>] __device_release_driver+0x7c/0xe0
[ 445.236654] [<ffffffff81345dc8>] driver_detach+0xc8/0xd0
[ 445.236654] [<ffffffff813454c8>] bus_remove_driver+0x88/0xe0
[ 445.236654] [<ffffffff81346572>] driver_unregister+0x62/0xa0
[ 445.236654] [<ffffffff812271d4>] pci_unregister_driver+0x44/0xc0
[ 445.236654] [<ffffffffa0211ce5>] iwl_pci_unregister_driver+0x15/0x20 [iwlagn]
[ 445.236654] [<ffffffffa022f595>] iwl_exit+0x9/0xa74 [iwlagn]
[ 445.236654] [<ffffffff810918f4>] sys_delete_module+0x184/0x240
[ 445.236654] [<ffffffff81452ece>] ? retint_swapgs+0xe/0x13
[ 445.236654] [<ffffffff8121098e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[ 445.236654] [<ffffffff81459e2b>] system_call_fastpath+0x16/0x1b
[ 445.236654] ---[ end trace 1fbc362b7dbe5d74 ]---
[ 445.236654] Mapped at:
[ 445.236654] [<ffffffff8121d7cb>] debug_dma_map_page+0x8b/0x150
[ 445.236654] [<ffffffffa021e7b7>] iwl_enqueue_hcmd+0x837/0xa40 [iwlagn]
[ 445.236654] [<ffffffffa021f92d>] iwl_trans_pcie_send_cmd+0x8d/0x580 [iwlagn]
[ 445.236654] [<ffffffffa01f7c75>] iwl_send_calib_results+0x75/0xd0 [iwlagn]
[ 445.236654] [<ffffffffa01f21f6>] iwlagn_alive_notify+0x196/0x1f0 [iwlagn]
[ 445.386500] iwlagn 0000:02:00.0: PCI INT A disabled
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The way we check if there is host command that should be reclaimed is
way too complicated. We should have a clear indication from the fw.
The fw is expected to set the SEQ_RX_FRAME bit if the frame was
originated by the fw which indicates to the driver that there is no
host command to free.
Somehow, there seem to have been buggy fw out there, hence the very
old comment.
This code checks if we have still buggy fw out there.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not doing so, the caldata continues to retain older history
values learned on that channel. It is always safer to start
noise floor calibration from the defaults after the assoication.
So this patch resets the nf history buffer when none of the
STA vifs are associated.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently during the full reset, the nf calibration is always
restarted from the defaults. The noise floor history buffers are
never be used again after the scan and ath reset. This patch
ensures that nf histories are always be used that helps to
improve the signal quality on congested environment
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
