Remove PSU EEPROM configuration for systems class equipped with
Mellanox chip Spectrum and Celeron CPU - system types MSN2700, MSN2100.
Till now all the systems from this class used few types of power units,
all equipped with EEPROM device with address space two bytes. Thus, all
these devices have been handled by EEPROM driver "24c02".
There is a new requirement is to support power unit replacement by "off
the shelf" device, matching electrical required parameters. Such device
can be equipped with different EEPROM type, which could be one byte
address space addressing or even could be not equipped with EEPROM.
In such case "24c02" will not work.
Fixes: c6acad68e ("platform/mellanox: mlxreg-hotplug: Modify to use a regmap interface")
Fixes: ba814fdd0 ("platform/x86: mlx-platform: Use defines for bus assignment")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20201125101056.174708-2-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add support to thinkpad_acpi for returning the status of the palm
sensor.
This patch builds on the work done previously for the input device
implementation (which was not needed). Both lap and palm sensor are using
sysfs and they are combined into the proxsensor block.
Note: On some platforms, because of an issue in the HW implementation,
the palm sensor presence may be incorrectly advertised as always
enabled even if a palm sensor is not present. The palm sensor is
intended for WWAN transmission power control and should be available
and correct on all WWAN enabled systems. It is not recommended to use
this interface for other use cases.
Signed-off-by: Mark Pearson <markpearson@lenovo.com>
Link: https://lore.kernel.org/r/20201124181154.547518-1-markpearson@lenovo.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When user presses Fn-F5, the driver automatically changes throttle
thermal policy (or fan boost mode, depending on laptop model).
It would be convenient for userspace software to be able to poll on
corresponding sysfs variable. For example, to show a notification about
mode change.
Note that there is currently no way to handle Fn-F5 from userspace
directly, driver does not pass it.
Signed-off-by: Vasiliy Kupriakov <rublag-ns@yandex.ru>
Link: https://lore.kernel.org/r/20200828214932.20866-2-rublag-ns@yandex.ru
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Pavilion 13 x360 PC has a chassis-type which does not indicate it is
a convertible, while it is actually a convertible. Add it to the
dmi_switches_allow_list.
Signed-off-by: Max Verevkin <me@maxverevkin.tk>
Link: https://lore.kernel.org/r/20201124131652.11165-1-me@maxverevkin.tk
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The lid state may change while the machine is suspended. As such, we may
need to re-check the state at wake-up time (at least when waking up from
hibernation).
Add the appropriate call to the resume handler in order to sync the
SW_TABLET_MODE switch state with the hardware state.
Fixes: dda3ec0aa6 ("platform/x86: thinkpad_acpi: Implement tablet mode using GMMS method")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=210269
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Acked-by: Henrique de Moraes Holschuh <hnh@hmh.eng.br>
Link: https://lore.kernel.org/r/20201123132157.866303-1-benjamin@sipsolutions.net
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The commit 78429e55e4 ("platform/x86: toshiba_acpi: Clean up
variable declaration") cleans up variable declaration in
video_proc_write(). Seems it does the variable assignment in the
wrong place, this results in dead code and changes the source code
logic. Fix it by doing the assignment at the beginning of the funciton.
Fixes: 78429e55e4 ("platform/x86: toshiba_acpi: Clean up variable declaration")
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Link: https://lore.kernel.org/r/1606024177-16481-1-git-send-email-kaixuxia@tencent.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
In addition to a 13" version, there is also a 15" (business) version of
the Surface Laptop 3 based on Intel CPUs. This version also handles
wakeup by lid via (unmarked) GPEs, so add support for it as well.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20201113223935.2073847-1-luzmaximilian@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The "ns->attr_grp" pointer can be NULL so this error handling code needs
to check for that to avoid an Oops.
Fixes: e2729113ce ("platform/x86: Intel PMT class driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20201117072251.GC1111239@mwanda
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201105110530.27888-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The driver depends on ACPI, ACPI_PTR() resolution is always the same.
Otherwise a compiler may produce a warning.
That said, the rule of thumb either ugly ifdeffery with ACPI_PTR or
none should be used in a driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201105110530.27888-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Panasonic laptops (at least from CF-W4 onwards) have dedicated firmware
registers for saving ac/dc and current brightness. They are a bit confusing
so here's some explanations:
AC_MIN_BRIGHT, AC_MAX_BRIGHT, DC_MIN_BRIGHT, DC_MAX_BRIGHT:
Read-only. Values: 0x01 and 0x15 respectively.
AC_CUR_BRIGHT, DC_CUR_BRIGHT:
Read-Write. 0x00-0xFF. Store user-defined AC/DC brightness. However,
they do not represent current brightness so they should be named AC_BRIGHT
and DC_BRIGHT instead.
CUR_BRIGHT (present since CF-W4):
Read-Write. 0x00-0xFF. It sets the current brightness. It won't update
itself if brightness is changed via other means, e.g. acpi_video0.
Another CUR_BRIGHT (added since CF-W5):
Read-Write. 0x01-0x15. Its value always synchronizes with current
brightness. Not implemented in this version.
Currently the backlight API interacts with AC_CUR_BRIGHT (probably because
it's the only bl register available in earlier models?). This patch adds
sysfs attributes for AC_CUR_BRIGHT, DC_CUR_BRIGHT and CUR_BRIGHT.
It also fixes the error of https://lkml.org/lkml/2020/8/19/1264.
PS: I think the backlight API should interact with CUR_BRIGHT instead of
AC_CUR_BRIGHT. But it involves complications like mapping between 0x01-0x15
or 0x00-0x14 (the backlight API) and 0x00-0xFF (CUR_BRIGHT). I'll leave the
discussion for a later version.
Signed-off-by: Kenneth Chan <kenneth.t.chan@gmail.com>
Link: https://lore.kernel.org/r/20200821181433.17653-10-kenneth.t.chan@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add battery charging threshold (aka ECO mode) support.
NOTE: The state of ECO mode is persistent until the next POST cycle which
reset it to previous state.
Signed-off-by: Kenneth Chan <kenneth.t.chan@gmail.com>
Link: https://lore.kernel.org/r/20200821181433.17653-9-kenneth.t.chan@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The return value of the sticky key on some models (e.g. CF-W5) do not
reflect its state. How to retrieve its state from firmware is unknown.
The safest bet is to reset it at module init and store its state in
pcc struct.
Signed-off-by: Kenneth Chan <kenneth.t.chan@gmail.com>
Link: https://lore.kernel.org/r/20200821181433.17653-6-kenneth.t.chan@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Replace ACPI prints with pr_*() macros for consistency with other platform
devices.
Clean up obsolete ACPI_HOTKEY_COMPONENT code.
Signed-off-by: Kenneth Chan <kenneth.t.chan@gmail.com>
Link: https://lore.kernel.org/r/20200821181433.17653-3-kenneth.t.chan@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The physical optical drive switch is present in Y and W series that
switches on the drive but fails to turn it off. The idea is to be able to
toggle the drive power by software and/or hardware. This patch merges
Martin Lucina <mato@kotelna.sk>'s work that took care of the software part.
Code is also added for the physical switch to power off the drive.
Signed-off-by: Kenneth Chan <kenneth.t.chan@gmail.com>
Link: https://lore.kernel.org/r/20200821181433.17653-2-kenneth.t.chan@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Got a dmesg message on my AMD Renoir based Acer laptop:
"acer_wmi: Unknown key number - 0x84" when toggling keyboard
background light
Signed-off-by: Timo Witte <timo.witte@gmail.com>
Reviewed-by: "Lee, Chun-Yi" <jlee@suse.com>
Link: https://lore.kernel.org/r/20200804001423.36778-1-timo.witte@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
According to the ACPI spec 9.1.1 _DSM (Device Specific Method),
intel_hid_dsm_fn_mask, acquired from function index 0, is "a buffer
containing one bit for each function index". When validitaing fn_index,
it should be compared with corresponding bit.
This buffer is usually longer than a byte. Depending on whether
INTEL_HID_DSM_HEBC_V2_FN exist, it could be either
"Buffer (0x02) { 0xFF, 0x01 }" or "Buffer (0x02) { 0xFF, 0x03 }".
Probably it won't grow larger according to the description. On older
platforms, available functions could be fewer or not supported at all,
i.e., "Buffer (One) { 0x00 }".
Signed-off-by: Zhen Gong <zhengong@usc.edu>
Link: https://lore.kernel.org/r/CAJCLVRCyp0ASdWTx-PxsrDC9zFBPw0U2AtPip+_Hpj2r5gUPwA@mail.gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fix the following coccinelle warnings:
./drivers/platform/x86/intel_pmc_core.c:932:1-16: WARNING: Assignment of 0/1 to bool variable
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/1604753621-7387-1-git-send-email-kaixuxia@tencent.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
AMD Power Management Controller driver a.k.a. amd-pmc driver is the
controller which is meant for the final S2Idle transaction that goes to
the PMFW running on the AMD SMU (System Management Unit) responsible for
tuning of the VDD.
Once all the monitored list or the idle constraints are met, this driver
would go and set the OS_HINT (meaning all the devices have reached to
their lowest state possible) via the SMU mailboxes.
This driver would also provide some debug capabilities via debugfs.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201105140531.2955555-1-Shyam-sundar.S-k@amd.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Thinkpad Yoga 11e 4th gen with the N3450 / Celeron CPU only has
one battery which is named BAT1 instead of the expected BAT0, add a
quirk for this. This fixes not being able to set the charging tresholds
on this model; and this alsoe fixes the following errors in dmesg:
ACPI: \_SB_.PCI0.LPCB.EC__.HKEY: BCTG evaluated but flagged as error
thinkpad_acpi: Error probing battery 2
battery: extension failed to load: ThinkPad Battery Extension
battery: extension unregistered: ThinkPad Battery Extension
Note that the added quirk is for the "R0K" BIOS versions which are
used on the Thinkpad Yoga 11e 4th gen's with a Celeron CPU, there
is a separate "R0L" BIOS for the i3/i5 based versions. This may also
need the same quirk, but if that really is necessary is unknown.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201109103550.16265-1-hdegoede@redhat.com
The Yoga 11e series has 2 accelerometers described by a BOSC0200 ACPI node.
This setup relies on a Windows service which reads both accelerometers and
then calculates the angle between the 2 halves to determine laptop / tent /
tablet mode and then reports the calculated mode back to the EC by calling
special ACPI methods on the BOSC0200 node.
The bmc150 iio driver does not support this (it involves double
calculations requiring sqrt and arccos so this really needs to be done
in userspace), as a result of this on the Yoga 11e the thinkpad_acpi
code always reports SW_TABLET_MODE=0, starting with GNOME 3.38 reporting
SW_TABLET_MODE=0 causes GNOME to:
1. Not show the onscreen keyboard when a text-input field is focussed
with the touchscreen.
2. Disable accelerometer based auto display-rotation.
This makes sense when in laptop-mode but not when in tablet-mode. But
since for the Yoga 11e the thinkpad_acpi code always reports
SW_TABLET_MODE=0, GNOME does not know when the device is in tablet-mode.
Stop reporting the broken (always 0) SW_TABLET_MODE on Yoga 11e models
to fix this.
Note there are plans for userspace to support 360 degree hinges style
2-in-1s with 2 accelerometers and figure out the mode by itself, see:
https://gitlab.freedesktop.org/hadess/iio-sensor-proxy/-/issues/216
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201106140130.46820-1-hdegoede@redhat.com
Tested on my P1 gen3, works fine with `thinkfan`. Since thinkpad_acpi fan
control is off by default, it is safe to add 2nd fan control for brave
overclockers
Signed-off-by: Iakov 'Jake' Kirilenko <jake.kirilenko@gmail.com>
Link: https://lore.kernel.org/r/20201105152556.34073-1-jake.kirilenko@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Calling release_attributes_data() while holding the "wmi_priv.mutex"
will lead to a dead lock. The other problem is that if kzalloc() fails
then this should return -ENOMEM but currently it returns success.
Fixes: e8a60aa740 ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201103101735.GB1127762@mwanda
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Conventionally, wake-up events for a specific device, in our case the
lid device, are managed via the ACPI _PRW field. While this does not
seem strictly necessary based on ACPI spec, the kernel disables GPE
wakeups to avoid non-wakeup interrupts preventing suspend by default and
only enables GPEs associated via the _PRW field with a wake-up capable
device. This behavior has been introduced in commit f941d3e41d ("ACPI:
EC / PM: Disable non-wakeup GPEs for suspend-to-idle") and is described
in more detail in its commit message.
Unfortunately, on MS Surface devices, there is no _PRW field present on
the lid device, thus no GPE is associated with it, and therefore the GPE
responsible for sending the status-change notification to the lid gets
disabled during suspend, making it impossible to wake the device via the
lid.
This patch introduces a pseudo-device and respective driver which, based
on some DMI matching, marks the corresponding GPE of the lid device for
wake and enables it during suspend. The behavior of this driver models
the behavior of the ACPI/PM core for normal wakeup GPEs, properly
declared via the _PRW field.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20201028105427.1593764-1-luzmaximilian@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
-----BEGIN PGP SIGNATURE-----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=l+RW
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-x86-v5.11' into review-hans
Immutable branch between MFD and x86 due for the v5.11 merge window
Add support for the Intel Platform Monitoring Technology crashlog
interface. This interface provides a few sysfs values to allow for
controlling the crashlog telemetry interface as well as a character
driver to allow for mapping the crashlog memory region so that it can be
accessed after a crashlog has been recorded.
This driver is meant to only support the server version of the crashlog
which is identified as crash_type 1 with a version of zero. Currently no
other types are supported.
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
PMT Telemetry is a capability of the Intel Platform Monitoring Technology.
The Telemetry capability provides access to device telemetry metrics that
provide hardware performance data to users from read-only register spaces.
With this driver present the intel_pmt directory can be populated with
telem<x> devices. These devices will contain the standard intel_pmt sysfs
data and a "telem" binary sysfs attribute which can be used to access the
telemetry data.
Also create a PCI device id list for early telemetry hardware that require
workarounds for known issues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Co-developed-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Platform Monitoring Technology is meant to provide a common way to
access telemetry and system metrics.
Register mappings are not provided by the driver. Instead, a GUID is read
from a header for each endpoint. The GUID identifies the device and is to
be used with an XML, provided by the vendor, to discover the available set
of metrics and their register mapping. This allows firmware updates to
modify the register space without needing to update the driver every time
with new mappings. Firmware writes a new GUID in this case to specify the
new mapping. Software tools with access to the associated XML file can
then interpret the changes.
The module manages access to all Intel PMT endpoints on a system,
independent of the device exporting them. It creates an intel_pmt class
to manage the devices. For each telemetry endpoint, sysfs files provide
GUID and size information as well as a pointer to the parent device the
telemetry came from. Software may discover the association between
endpoints and devices by iterating through the list in sysfs, or by looking
for the existence of the class folder under the device of interest. A
binary sysfs attribute of the same name allows software to then read or map
the telemetry space for direct access.
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix the following sparse warnings:
./passobj-attributes.c:38:23: warning: symbol 'po_is_pass_set' was not declared. Should it be static?
./passobj-attributes.c:70:23: warning: symbol 'po_current_password' was not declared. Should it be static?
./passobj-attributes.c:99:23: warning: symbol 'po_new_password' was not declared. Should it be static?
./passobj-attributes.c:103:23: warning: symbol 'po_min_pass_length' was not declared. Should it be static?
./passobj-attributes.c:107:23: warning: symbol 'po_max_pass_length' was not declared. Should it be static?
./passobj-attributes.c:116:23: warning: symbol 'po_mechanism' was not declared. Should it be static?
./passobj-attributes.c:129:23: warning: symbol 'po_role' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1604107922-14950-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fix the following sparse warning:
drivers/platform/x86/dell-wmi-sysman/sysman.c:258:24: warning:
symbol 'wmi_sysman_kobj_sysfs_ops' was not declared.
Should it be static?
wmi_sysman_kobj_sysfs_ops has only call within sysman.c
It should be static
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1603971581-64135-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add support for SW_TABLET_MODE on the Acer Switch 10 (SW5-012) and the
acer Switch 10 (S1003) models.
There is no way to detect if this is supported, so this uses DMI based
quirks setting force_caps to ACER_CAP_KBD_DOCK (these devices have no
other acer-wmi based functionality).
The new SW_TABLET_MODE functionality can be tested on devices which
are not in the DMI table by passing acer_wmi.force_caps=0x40 on the
kernel commandline.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201019185628.264473-6-hdegoede@redhat.com
Not all devices supporting WMID_GUID3 support the wmid3_set_function_mode()
call, leading to errors like these:
[ 60.138358] acer_wmi: Enabling RF Button failed: 0x1 - 0xff
[ 60.140036] acer_wmi: Enabling Launch Manager failed: 0x1 - 0xff
Add an ACER_CAP_SET_FUNCTION_MODE capability flag, so that these calls
can be disabled through the new force_caps mechanism.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201019185628.264473-5-hdegoede@redhat.com
Add a new force_caps module parameter to allow overriding the drivers
builtin capability detection mechanism.
This can be used to for example:
-Disable rfkill functionality on devices where there is an AA OEM DMI
record advertising non functional rfkill switches
-Force loading of the driver on devices with a missing AA OEM DMI record
Note that force_caps is -1 when unset, this allows forcing the
capability field to 0, which results in acer-wmi only providing WMI
hotkey handling while disabling all other (led, rfkill, backlight)
functionality.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201019185628.264473-4-hdegoede@redhat.com
Cleanup accelerometer device handling:
-Drop acer_wmi_accel_destroy instead directly call input_unregister_device.
-The information tracked by the CAP_ACCEL flag mirrors acer_wmi_accel_dev
being NULL. Drop the CAP flag, this is a preparation change for allowing
users to override the capability flags. Dropping the flag stops users
from causing a NULL pointer dereference by forcing the capability.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201019185628.264473-3-hdegoede@redhat.com
Cleanup the ACER_CAP_FOO defines:
-Switch to using BIT() macro.
-The ACER_CAP_RFBTN flag is set, but it is never checked anywhere, drop it.
-Drop the unused ACER_CAP_ANY define.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201019185628.264473-2-hdegoede@redhat.com
set_quirks has a "if (!interface) return;" check at its beginning and
interface always is NULL when set_quirks is called from find_quirks,
so it is a no-op and we can drop it.
This also allows dropping the "if (!interface) return;" from set_quirks
since set_quirks now always is called with interface != NULL.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201019185628.264473-1-hdegoede@redhat.com
The UX360CA has a WMI device id 0x00060062, which reports whether the
lid is flipped in tablet mode (1) or in normal laptop mode (0).
Add a quirk (quirk_asus_use_lid_flip_devid) for devices on which this
WMI device should be used to figure out the SW_TABLET_MODE state, as
opposed to the quirk_asus_use_kbd_dock_devid.
Additionally, the device needs to be queried on resume and restore
because the firmware does not generate an event if the laptop is put to
sleep while in tablet mode, flipped to normal mode, and later awoken.
It is assumed other UX360* models have the same WMI device. As such, the
quirk is applied to devices with DMI_MATCH(DMI_PRODUCT_NAME, "UX360").
More devices with this feature need to be tested and added accordingly.
The reason for using an allowlist via the quirk mechanism is that the new
WMI device (0x00060062) is also present on some models which do not have
a 360 degree hinge (at least FX503VD and GL503VD from Hans' DSTS
collection) and therefore its presence cannot be relied on.
Signed-off-by: Samuel Čavoj <samuel@cavoj.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201020220944.1075530-1-samuel@cavoj.net
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The performance modules in BlueField are present in several hardware
blocks and each block provides access to these stats either through
counters that can be programmed to monitor supported events or
through memory-mapped registers that hold the relevant information.
The hardware blocks that include a performance module are:
* Tile (block containing 2 cores and a shared L2 cache)
* TRIO (PCIe root complex)
* MSS (Memory Sub-system containing the Memory Controller and L3 cache)
* GIC (Interrupt controller)
* SMMU (System Memory Management Unit)
The mlx_pmc driver provides access to all of these performance modules
through a hwmon sysfs interface.
v2 --> v3
Update copyright info.
v1 --> v2
Remove unused headers.
Add comma to arrays where last line is not a termination.
Use kstrtoint in place of sscanf.
UUID manipulation follows drivers/platform/mellanox/mlxbf-bootctl.c
Signed-off-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/4e19a1e5bf4197ad27fc57981fd280eaebd23577.1602160468.git.shravankr@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Dell WMI Systems Management Driver provides a sysfs
interface for systems management to enable BIOS configuration
capability on certain Dell Systems.
This driver allows user to configure Dell systems with a
uniform common interface. To facilitate this, the patch
introduces a generic way for driver to be able to create
configurable BIOS Attributes available in Setup (F2) screen.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: mark gross <mgross@linux.intel.com>
Co-developed-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Co-developed-by: Prasanth KSR <prasanth.ksr@dell.com>
Signed-off-by: Prasanth KSR <prasanth.ksr@dell.com>
Signed-off-by: Divya Bharathi <divya.bharathi@dell.com>
Link: https://lore.kernel.org/r/20201027134944.316730-1-divya.bharathi@dell.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This reverts commit 7b11e89896.
Consider the following hardware setting.
|-PNP0C14:00
| |-- device #1
|-PNP0C14:01
| |-- device #2
When unloading wmi driver module, device #2 will be first unregistered.
But device_destroy() using MKDEV(0, 0) will locate PNP0C14:00 first
and unregister it. This is incorrect. Should use device_unregister() to
unregister the real parent device.
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Link: https://lore.kernel.org/r/20191115052710.46880-1-yongxin.liu@windriver.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
