There are some chances that the actual base of hardware is different
from the value recorded by driver, so we have to reset the variable
of ocp_base to sync it.
Set ocp_base to -1. Then, it would be updated and the new base would be
set to the hardware next time.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It needs to set mdio force mode. Otherwise, link off always occurs when
setting force speed.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like ThinkaPad Thunderbolt 4 Dock, more Lenovo docks start to use the original
Realtek USB ethernet chip ID 0bda:8153.
Lenovo Docks always use their own IDs for usb hub, even for older Docks.
If parent hub is from Lenovo, then r8152 should try MAC passthrough.
Verified on Lenovo TBT3 dock too.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert usb drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
Manually checked these are either usbnet or pure etherdevs.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the situation that the disconnect event comes very late when the
device is unplugged, the driver would resubmit the RX bulk transfer
after getting the callback with -EPROTO immediately and continually.
Finally, soft lockup occurs.
This patch avoids to resubmit RX immediately. It uses a workqueue to
schedule the RX NAPI. And the NAPI would resubmit the RX. It let the
disconnect event have opportunity to stop the submission before soft
lockup.
Reported-by: Jason-ch Chen <jason-ch.chen@mediatek.com>
Tested-by: Jason-ch Chen <jason-ch.chen@mediatek.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Convert net/usb from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The maximum PLA bp number of RTL8153C is 16, not 8. That is, the
bp 0 ~ 15 are at 0xfc28 ~ 0xfc46, and the bp_en is at 0xfc48.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register of USB_BP2_EN is 16 bits, so we should use
ocp_write_word(), not ocp_write_byte().
Fixes: 9370f2d05a ("support request_firmware for RTL8153")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8152 driver sets up the MAC address at reset-resume, while
rtl8152_set_mac_address() has the temporary autopm get/put. This may
lead to a deadlock as the PM lock has been already taken for the
execution of the runtime PM callback.
This patch adds the workaround to avoid the superfluous autpm when
called from rtl8152_reset_resume().
Link: https://bugzilla.suse.com/show_bug.cgi?id=1186194
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8152_close() takes the refcount via usb_autopm_get_interface() but
it doesn't release when RTL8152_UNPLUG test hits. This may lead to
the imbalance of PM refcount. This patch addresses it.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1186194
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Store the information of the pipes to avoid calling usb_rcvctrlpipe(),
usb_sndctrlpipe(), usb_rcvbulkpipe(), usb_sndbulkpipe(), and
usb_rcvintpipe() frequently.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support get_pauseparam and set_pauseparam of ethtool_ops.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify some fields of the USB descriptor to make sure the driver
could be used by the device.
Besides, remove the check of endpoint number in rtl8152_probe().
usb_find_common_endpoints() includes it.
BugLink: https://syzkaller.appspot.com/bug?id=912c9c373656996801b4de61f1e3cb326fe940aa
Reported-by: syzbot+95afd23673f5dd295c57@syzkaller.appspotmail.com
Fixes: c2198943e3 ("r8152: search the configuration of vendor mode")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove DELL_TB_RX_AGG_BUG and LENOVO_MACPASSTHRU flags of rtl8152_flags.
They are only set when initializing and wouldn't be change. It is enough
to record them with variables.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefine REALTEK_USB_DEVICE macro with USB_DEVICE_INTERFACE_CLASS and
USB_DEVICE_AND_INTERFACE_INFO to simply the code.
Although checkpatch.pl shows the following error, it is more readable.
ERROR: Macros with complex values should be enclosed in parentheses
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8156 support CDC NCM mode. And users could set the configuration
of the USB device between vendor and NCM mode dynamically by themselves.
That is, the driver doesn't need to set vendor mode from NCM mode.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the timeout occurs, we still have to run the following process
for releasing patch request. Otherwise, the PHY would keep no link.
Therefore, use break to stop the loop of loading firmware and
release the patch request rather than return the function directly.
Fixes: 4a51b0e8a0 ("r8152: support PHY firmware for RTL8156 series")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vendor mode is not always at config #1, so it is necessary to
set the correct configuration number.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support new firmware type and method for RTL8156 series.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support RTL8153C, RTL8153D, RTL8156A, and RTL8156B. The RTL8156A
and RTL8156B are the 2.5G ethernet.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The different chips may have different requests when changing mtu.
Therefore, add a new help function of rtl_ops to change mtu. Besides,
reset the tx/rx after changing mtu.
Additionally, add mtu_to_size() and size_to_mtu() macros to simplify
the code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use bits operations to record and check the firmware.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the maximum inter frame gap time (144ns) for speed 10M/half and
100M/half. It improves the performance for those speeds. And, there
is no effect for the other speeds.
For 10M/half and 100M/half, the fast inter frame gap time let the
device couldn't use the feature of the aggregation effectively,
because the transfer would be completed fastly. Therefore, use the
maximum value to improve the effect of the aggregation. However, you
may not feel the improvement for fast CPUs, because they compensate
for the effect of the aggregation.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the USB host controller is EHCI, the throughput is reduced from
300Mb/s to 60Mb/s, when the rx buffer size is modified from 16K to
32K.
According to the EHCI spec, the maximum size of the qTD is 20K.
Therefore, when the driver uses more than 20K buffer, the latency
time of EHCI would be increased. And, it let the RTL8153A get worse
throughput.
However, the driver uses alloc_pages() for rx buffer, so I limit
the rx buffer to 16K rather than 20K.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205923
Fixes: ec5791c202 ("r8152: separate the rx buffer size")
Reported-by: Robert Davies <robdavies1977@gmail.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 134f98bcf1.
The r8153_mac_clk_spd() is used for RTL8153A only, because the register
table of RTL8153B is different from RTL8153A. However, this function would
be called when RTL8153B calls r8153_first_init() and r8153_enter_oob().
That causes RTL8153B becomes unstable when suspending and resuming. The
worst case may let the device stop working.
Besides, revert this commit to disable MAC clock speed down for RTL8153A.
It would avoid the known issue when enabling U1. The data of the first
control transfer may be wrong when exiting U1.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some messages are before calling register_netdev(), so replace
netif_err() with dev_err().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Return error code if autosuspend_en, eee_get, or eee_set don't exist.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
U1/U2 shoued be enabled for USB 3.0 or later. The USB 2.0 doesn't
support it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For runtime resuming, the RTL8153B may be resumed from the state
of power cut, when enabling the feature of UPS. Then, the PHY
would be reset, so it is necessary to be initailized again.
Besides, the USB_U1U2_TIMER also has to be set again, so I move
it from r8153b_init() to r8153b_hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace r8153_patch_request() with rtl_phy_patch_request().
Replace r8153_pre_ram_code() with rtl_pre_ram_code().
Replace r8153_post_ram_code() with rtl_post_ram_code().
Add rtl_patch_key_set().
The new functions have an additional parameter. It is used to wait
the patch request command finished. When the PHY is resumed from
the state of power cut, the PHY is at a safe mode and the
OCP_PHY_PATCH_STAT wouldn't be updated. For this situation, it is
safe to set patch request command without waiting OCP_PHY_PATCH_STAT.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This USB-C Hub (17ef:721e) based on the Realtek RTL8153B chip used to
use the cdc_ether driver. However, using this driver, with the system
suspended the device constantly sends pause-frames as soon as the
receive buffer fills up. This causes issues with other devices, where
some Ethernet switches stop forwarding packets altogether.
Using the Realtek driver (r8152) fixes this issue. Pause frames are no
longer sent while the host system is suspended.
Signed-off-by: Leon Schuermann <leon@is.currently.online>
Tested-by: Leon Schuermann <leon@is.currently.online>
Link: https://lore.kernel.org/r/20210111190312.12589-2-leon@is.currently.online
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support ECM mode based on cdc_ether with relative mii functions,
when CONFIG_USB_RTL8152 is not set, or the device is not supported
by r8152 driver.
Both r8152 and r8153_ecm would check the return value of
rtl8152_get_version() in porbe(). If rtl8152_get_version()
return none zero value, the r8152 is used for the device
with vendor mode. Otherwise, the r8153_ecm is used for the
device with ECM mode.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/1394712342-15778-392-Taiwan-albertk@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/r8152.c:992: warning: Function parameter or member 'mode_pre' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:992: warning: Function parameter or member 'mode_post' not described in 'fw_phy_nc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20201102114512.1062724-28-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/r8152.c:934: warning: Function parameter or member 'blk_hdr' not described in 'fw_mac'
drivers/net/usb/r8152.c:934: warning: Function parameter or member 'reserved' not described in 'fw_mac'
drivers/net/usb/r8152.c:947: warning: Function parameter or member 'blk_hdr' not described in 'fw_phy_patch_key'
drivers/net/usb/r8152.c:947: warning: Function parameter or member 'reserved' not described in 'fw_phy_patch_key'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'blk_hdr' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'mode_pre' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'mode_post' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'reserved' not described in 'fw_phy_nc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20201102114512.1062724-23-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Query the USB device's device tree node when looking for a MAC address.
The struct device embedded into the struct net_device does not have a
device tree node attached at all.
The reason why this went unnoticed is because the system where this was
tested was one of the few development units that had its OTP programmed,
as opposed to production systems where the MAC address is stored in a
separate EEPROM and is passed via device tree by the firmware.
Reported-by: EJ Hsu <ejh@nvidia.com>
Fixes: acb6d3771a ("r8152: Use MAC address from device tree if available")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: EJ Hsu <ejh@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Device id 0927 is the RTL8153B-based component of the 'Surface USB-C to
Ethernet and USB Adapter' and may be used as a component of other devices
in future. Tested and working with the r8152 driver.
Update the cdc_ether blacklist due to the RTL8153 'network jam on suspend'
issue which this device will cause (personally confirmed).
Signed-off-by: Marc Payne <marc.payne@mdpsys.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a MAC address was passed via the device tree node for the r8152
device, use it and fall back to reading from EEPROM otherwise. This is
useful for devices where the r8152 EEPROM was not programmed with a
valid MAC address, or if users want to explicitly set a MAC address in
the bootloader and pass that to the kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski