Add new device generic parameter to determine the size of the
asynchronous control events EQ.
For example, to reduce event EQ size to 64, execute:
$ devlink dev param set pci/0000:06:00.0 \
name event_eq_size value 64 cmode driverinit
$ devlink dev reload pci/0000:06:00.0
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add new device generic parameter to determine the size of the
I/O completion EQs.
For example, to reduce I/O EQ size to 64, execute:
$ devlink dev param set pci/0000:06:00.0 \
name io_eq_size value 64 cmode driverinit
$ devlink dev reload pci/0000:06:00.0
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
We want to track all dev_hold()/dev_put() to ease leak hunting.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The devlink_resources_unregister() used second parameter as an
entry point for the recursive removal of devlink resources. None
of the callers outside of devlink core needed to use this field,
so let's remove it.
As part of this removal, the "struct devlink_resource" was moved
from .h to .c file as it is not possible to use in any place in
the code except devlink.c.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new device generic parameter to enable and disable
iWARP functionality on a multi-protocol RDMA device.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Leszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
devlink compat code needs to drop rtnl_lock to take
devlink->lock to ensure correct lock ordering.
This is problematic because we're not strictly guaranteed
that the netdev will not disappear after we re-lock.
It may open a possibility of nested ->begin / ->complete
calls.
Instead of calling into devlink under rtnl_lock take
a ref on the devlink instance and make the call after
we've dropped rtnl_lock.
We (continue to) assume that netdevs have an implicit
reference on the devlink returned from ndo_get_devlink_port
Note that ndo_get_devlink_port will now get called
under rtnl_lock. That should be fine since none of
the drivers seem to be taking serious locks inside
ndo_get_devlink_port.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow those who hold implicit reference on a devlink instance
to try to take a full ref on it. This will be used from netdev
code which has an implicit ref because of driver call ordering.
Note that after recent changes devlink_unregister() may happen
before netdev unregister, but devlink_free() should still happen
after, so we are safe to try, but we can't just refcount_inc()
and assume it's not zero.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change of devlink_register() to be last devlink command together
with delayed notification logic made the publish API to be obsolete.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit a0c76345e3 ("devlink: disallow reload operation during device
cleanup") added devlink_reload_{enable,disable}() APIs to prevent reload
operation from racing with device probe/dismantle.
After recent changes to move devlink_register() to the end of device
probe and devlink_unregister() to the beginning of device dismantle,
these races can no longer happen. Reload operations will be denied if
the devlink instance is unregistered and devlink_unregister() will block
until all in-flight operations are done.
Therefore, remove these devlink_reload_{enable,disable}() APIs.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce new devlink call to set feature mask to control devlink
behavior during device initialization phase after devlink_alloc()
is already called.
This allows us to set reload ops based on device property which
is not known at the beginning of driver initialization.
For the sake of simplicity, this API lacks any type of locking and
needs to be called before devlink_register() to make sure that no
parallel access to the ops is possible at this stage.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both netdev_to_devlink and netdev_to_devlink_port are used in devlink.c
only, so move them in order to reduce their scope.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The declaration of struct devlink in general header provokes the
situation where internal fields can be accidentally used by the driver
authors. In order to reduce such possible situations, let's reduce the
namespace exposure of struct devlink.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no in-kernel users for the devlink port parameters API,
so let's remove it.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink_register() can't fail and always returns success, but all drivers
are obligated to check returned status anyway. This adds a lot of boilerplate
code to handle impossible flow.
Make devlink_register() void and simplify the drivers that use that
API call.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com> # dsa
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink core exported generously the functions calls that were used
by netdevsim tests or not used at all.
Delete such APIs with one exception - devlink_alloc_ns(). That function
should be spared from deleting because it is a special form of devlink_alloc()
needed for the netdevsim.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need in specific devlink_param_*publish(), because same
output can be achieved by using devlink_params_*publish() in correct
places.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use xarray instead of linearly organized linked lists for the
devlink instances. This will let us revise the locking scheme in favour
of internal xarray locking that protects database.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct devlink itself is protected by internal lock and doesn't
need global lock during operation. That global lock is used to protect
addition/removal new devlink instances from the global list in use by
all devlink consumers in the system.
The future conversion of linked list to be xarray will allow us to
actually delete that lock, but first we need to count all struct devlink
users.
The reference counting provides us a way to ensure that no new user
space commands success to grab devlink instance which is going to be
destroyed makes it is safe to access it without lock.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable drivers to publish/unpublish individual parameter.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently device configuration parameters can be registered as an array.
Due to this a constant array must be registered. A single driver
supporting multiple devices each with different device capabilities end
up registering all parameters even if it doesn't support it.
One possible workaround a driver can do is, it registers multiple single
entry arrays to overcome such limitation.
Better is to provide a API that enables driver to register/unregister a
single parameter. This also further helps in two ways.
(1) to reduce the memory of devlink_param_entry by avoiding in registering
parameters which are not supported by the device.
(2) avoid generating multiple parameter add, delete, publish, unpublish,
init value notifications for such unsupported parameters
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new device generic parameter to enable/disable creation of
VDPA net auxiliary device and associated device functionality
in the devlink instance.
User who prefers to disable such functionality can disable it using below
example.
$ devlink dev param set pci/0000:06:00.0 \
name enable_vnet value false cmode driverinit
$ devlink dev reload pci/0000:06:00.0
At this point devlink instance do not create auxiliary device for the
VDPA net functionality.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new device generic parameter to enable/disable creation of
RDMA auxiliary device and associated device functionality
in the devlink instance.
User who prefers to disable such functionality can disable it using below
example.
$ devlink dev param set pci/0000:06:00.0 \
name enable_rdma value false cmode driverinit
$ devlink dev reload pci/0000:06:00.0
At this point devlink instance do not create auxiliary device for the
RDMA functionality.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new device generic parameter to enable/disable creation of
Ethernet auxiliary device and associated device functionality
in the devlink instance.
User who prefers to disable such functionality can disable it using below
example.
$ devlink dev param set pci/0000:06:00.0 \
name enable_eth value false cmode driverinit
$ devlink dev reload pci/0000:06:00.0
At this point devlink instance do not create auxiliary device for the
Ethernet functionality.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All kernel devlink implementations call to devlink_alloc() during
initialization routine for specific device which is used later as
a parent device for devlink_register().
Such late device assignment causes to the situation which requires us to
call to device_register() before setting other parameters, but that call
opens devlink to the world and makes accessible for the netlink users.
Any attempt to move devlink_register() to be the last call generates the
following error due to access to the devlink->dev pointer.
[ 8.758862] devlink_nl_param_fill+0x2e8/0xe50
[ 8.760305] devlink_param_notify+0x6d/0x180
[ 8.760435] __devlink_params_register+0x2f1/0x670
[ 8.760558] devlink_params_register+0x1e/0x20
The simple change of API to set devlink device in the devlink_alloc()
instead of devlink_register() fixes all this above and ensures that
prior to call to devlink_register() everything already set.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink port already has pointer to the devlink instance and all API
calls that forward these devlink ports to the drivers perform same
"devlink_port->devlink" assignment before actual call.
This patch removes useless parameter and allows us in the future
to create specific devlink_port_ops to manage user space access with
reliable ops assignment.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need in extra call indirection and check from impossible
flow where someone tries to set namespace without prior call
to devlink_alloc().
Instead of this extra logic and additional EXPORT_SYMBOL, use specialized
devlink allocation function that receives net namespace as an argument.
Such specialized API allows clear view when devlink initialized in wrong
net namespace and/or kernel users don't try to change devlink namespace
under the hood.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both registered flag and devlink pointer are set at the same time
and indicate the same thing - devlink/devlink_port are ready. Instead
of checking ->registered use devlink pointer as an indication.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever query statistics is issued for trap, devlink subsystem
would also fill-in statistics 'dropped' field. This field indicates
the number of packets HW dropped and failed to report to the device driver,
and thus - to the devlink subsystem itself.
In case if device driver didn't register callback for hard drop
statistics querying, 'dropped' field will be omitted and not filled.
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor DEVLINK_CMD_RATE_{GET|SET} command handlers to support setting
a node as a parent for another rate object (leaf or node) by means of
new attribute DEVLINK_ATTR_RATE_PARENT_NODE_NAME. Extend devlink ops
with new callbacks rate_{leaf|node}_parent_set() to set node as a parent
for rate object to allow supporting drivers to implement rate grouping
through devlink. Driver implementations are allowed to support leafs
or node children only. Invoking callback with NULL as parent should be
threated by the driver as unset parent action.
Extend rate object struct with reference counter to disallow deleting a
node with any child pointing to it. User should unset parent for the
child explicitly.
Example:
$ devlink port function rate add netdevsim/netdevsim10/group1
$ devlink port function rate add netdevsim/netdevsim10/group2
$ devlink port function rate set netdevsim/netdevsim10/group1 parent group2
$ devlink port function rate show netdevsim/netdevsim10/group1
netdevsim/netdevsim10/group1: type node parent group2
$ devlink port function rate set netdevsim/netdevsim10/group1 noparent
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for DEVLINK_CMD_RATE_{NEW|DEL} commands that are used
to create and delete devlink rate nodes. Add new attribute
DEVLINK_ATTR_RATE_NODE_NAME that specify node name string. The node name
is an alphanumeric identifier. No valid node name can be a devlink port
index, eg. decimal number. Extend devlink ops with new callbacks
rate_node_{new|del}() and rate_node_tx_{share|max}_set() to allow
supporting drivers to implement ports rate grouping and setting tx rate
of rate nodes through devlink.
Expose devlink_rate_nodes_destroy() function to allow vendor driver do
proper cleanup of internally allocated resources for the nodes if the
driver goes down or due to any other reasons which requires nodes to be
destroyed.
Disallow moving device from switchdev to legacy mode if any node exists
on that device. User must explicitly delete nodes before switching mode.
Example:
$ devlink port function rate add netdevsim/netdevsim10/group1
$ devlink port function rate set netdevsim/netdevsim10/group1 \
tx_share 10mbit tx_max 100mbit
Add + set command can be combined:
$ devlink port function rate add netdevsim/netdevsim10/group1 \
tx_share 10mbit tx_max 100mbit
$ devlink port function rate show netdevsim/netdevsim10/group1
netdevsim/netdevsim10/group1: type node tx_share 10mbit tx_max 100mbit
$ devlink port function rate del netdevsim/netdevsim10/group1
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for DEVLINK_CMD_RATE_SET command with new attributes
DEVLINK_ATTR_RATE_TX_{SHARE|MAX} that are used to set devlink rate
shared/max tx rate values. Extend devlink ops with new callbacks
rate_leaf_tx_{share|max}_set() to allow supporting drivers to implement
rate control through devlink.
New attributes are optional. Driver implementations are allowed to
support either or both of them.
Shared rate example:
$ devlink port function rate set netdevsim/netdevsim10/0 tx_share 10mbit
$ devlink port function rate show netdevsim/netdevsim10/0
netdevsim/netdevsim10/0: type leaf tx_share 10mbit
Max rate example:
$ devlink port function rate set netdevsim/netdevsim10/0 tx_max 100mbit
$ devlink port function rate show netdevsim/netdevsim10/0
netdevsim/netdevsim10/0: type leaf tx_max 100mbit
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow registering rate object for devlink ports with dedicated
devlink_rate_leaf_{create|destroy}() API. Implement new netlink
DEVLINK_CMD_RATE_GET command that is used to retrieve rate object info.
Add new DEVLINK_CMD_RATE_{NEW|DEL} commands that are used for
notifications when creating/deleting leaf rate object.
Rate API is intended to be used for rate limiting of individual
devlink ports (leafs) and their aggregates (nodes).
Example:
$ devlink port show
pci/0000:03:00.0/0
pci/0000:03:00.0/1
$ devlink port function rate show
pci/0000:03:00.0/0: type leaf
pci/0000:03:00.0/1: type leaf
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extended SF port attributes to have optional external flag similar to
PCI PF and VF port attributes.
External atttibute is required to generate unique phys_port_name when PF number
and SF number are overlapping between two controllers similar to SR-IOV
VFs.
When a SF is for external controller an example view of external SF
port and config sequence.
On eswitch system:
$ devlink dev eswitch set pci/0033:01:00.0 mode switchdev
$ devlink port show
pci/0033:01:00.0/196607: type eth netdev enP51p1s0f0np0 flavour physical port 0 splittable false
pci/0033:01:00.0/131072: type eth netdev eth0 flavour pcipf controller 1 pfnum 0 external true splittable false
function:
hw_addr 00:00:00:00:00:00
$ devlink port add pci/0033:01:00.0 flavour pcisf pfnum 0 sfnum 77 controller 1
pci/0033:01:00.0/163840: type eth netdev eth1 flavour pcisf controller 1 pfnum 0 sfnum 77 splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
phys_port_name construction:
$ cat /sys/class/net/eth1/phys_port_name
c1pf0sf77
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Parav Pandit Says:
=================
This patchset introduces support for mlx5 subfunction (SF).
A subfunction is a lightweight function that has a parent PCI function on
which it is deployed. mlx5 subfunction has its own function capabilities
and its own resources. This means a subfunction has its own dedicated
queues(txq, rxq, cq, eq). These queues are neither shared nor stolen from
the parent PCI function.
When subfunction is RDMA capable, it has its own QP1, GID table and rdma
resources neither shared nor stolen from the parent PCI function.
A subfunction has dedicated window in PCI BAR space that is not shared
with the other subfunctions or parent PCI function. This ensures that all
class devices of the subfunction accesses only assigned PCI BAR space.
A Subfunction supports eswitch representation through which it supports tc
offloads. User must configure eswitch to send/receive packets from/to
subfunction port.
Subfunctions share PCI level resources such as PCI MSI-X IRQs with
their other subfunctions and/or with its parent PCI function.
Patch summary:
--------------
Patch 1 to 4 prepares devlink
patch 5 to 7 mlx5 adds SF device support
Patch 8 to 11 mlx5 adds SF devlink port support
Patch 12 and 14 adds documentation
Patch-1 prepares code to handle multiple port function attributes
Patch-2 introduces devlink pcisf port flavour similar to pcipf and pcivf
Patch-3 adds port add and delete driver callbacks
Patch-4 adds port function state get and set callbacks
Patch-5 mlx5 vhca event notifier support to distribute subfunction
state change notification
Patch-6 adds SF auxiliary device
Patch-7 adds SF auxiliary driver
Patch-8 prepares eswitch to handler SF vport
Patch-9 adds eswitch helpers to add/remove SF vport
Patch-10 implements devlink port add/del callbacks
Patch-11 implements devlink port function get/set callbacks
Patch-12 to 14 adds documentation
Patch-12 added mlx5 port function documentation
Patch-13 adds subfunction documentation
Patch-14 adds mlx5 subfunction documentation
Subfunction support is discussed in detail in RFC [1] and [2].
RFC [1] and extension [2] describes requirements, design and proposed
plumbing using devlink, auxiliary bus and sysfs for systemd/udev
support. Functionality of this patchset is best explained using real
examples further below.
overview:
--------
A subfunction can be created and deleted by a user using devlink port
add/delete interface.
A subfunction can be configured using devlink port function attribute
before its activated.
When a subfunction is activated, it results in an auxiliary device on
the host PCI device where it is deployed. A driver binds to the
auxiliary device that further creates supported class devices.
example subfunction usage sequence:
-----------------------------------
Change device to switchdev mode:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
Add a devlink port of subfunction flavour:
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
Configure mac address of the port function:
$ devlink port function set ens2f0npf0sf88 hw_addr 00:00:00:00:88:88
Now activate the function:
$ devlink port function set ens2f0npf0sf88 state active
Now use the auxiliary device and class devices:
$ devlink dev show
pci/0000:06:00.0
auxiliary/mlx5_core.sf.4
$ ip link show
127: ens2f0np0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 24:8a:07:b3:d1:12 brd ff:ff:ff:ff:ff:ff
altname enp6s0f0np0
129: p0sf88: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 00:00:00:00:88:88 brd ff:ff:ff:ff:ff:ff
$ rdma dev show
43: rdmap6s0f0: node_type ca fw 16.29.0550 node_guid 248a:0703:00b3:d112 sys_image_guid 248a:0703:00b3:d112
44: mlx5_0: node_type ca fw 16.29.0550 node_guid 0000:00ff:fe00:8888 sys_image_guid 248a:0703:00b3:d112
After use inactivate the function:
$ devlink port function set ens2f0npf0sf88 state inactive
Now delete the subfunction port:
$ devlink port del ens2f0npf0sf88
[1] https://lore.kernel.org/netdev/20200519092258.GF4655@nanopsycho/
[2] https://marc.info/?l=linux-netdev&m=158555928517777&w=2
=================
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmALKDwACgkQSD+KveBX
+j7qjQf6A1moPhhIlXROCzaJUjlAj2U291LWBveU+I6na6fjYjAAWHYwfv0YKQpo
Qb0NRt+9abgEpGidc4hOwIJKhK+vlWrQuehRt83aAfAwaN3OEeGuNllniWo821Hj
sNiJfSC/DslOlQSxKLsAs3Fduy/sV3GN9Zv7hEwOFgEr5QvB2c6H1XiypVP2Ecsd
ZXC3SuEWxIoRtfXEkTkJne9LNoiDChlvT1FR/z75h8HUBdAOjzBTQzBbM+8M4Msw
8aKUPya3FMRAPWsOgPhkpU0xTtH2Mi7MC9TlwiWmrK4Q3uvesIav8pVf7r3GNAZA
sipIZ4gP0M5SiCaZa8rIBpTXBHxmvg==
=jEG4
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 subfunction support
Parav Pandit says:
This patchset introduces support for mlx5 subfunction (SF).
A subfunction is a lightweight function that has a parent PCI function on
which it is deployed. mlx5 subfunction has its own function capabilities
and its own resources. This means a subfunction has its own dedicated
queues(txq, rxq, cq, eq). These queues are neither shared nor stolen from
the parent PCI function.
When subfunction is RDMA capable, it has its own QP1, GID table and rdma
resources neither shared nor stolen from the parent PCI function.
A subfunction has dedicated window in PCI BAR space that is not shared
with the other subfunctions or parent PCI function. This ensures that all
class devices of the subfunction accesses only assigned PCI BAR space.
A Subfunction supports eswitch representation through which it supports tc
offloads. User must configure eswitch to send/receive packets from/to
subfunction port.
Subfunctions share PCI level resources such as PCI MSI-X IRQs with
their other subfunctions and/or with its parent PCI function.
Subfunction support is discussed in detail in RFC [1] and [2].
RFC [1] and extension [2] describes requirements, design and proposed
plumbing using devlink, auxiliary bus and sysfs for systemd/udev
support. Functionality of this patchset is best explained using real
examples further below.
overview:
--------
A subfunction can be created and deleted by a user using devlink port
add/delete interface.
A subfunction can be configured using devlink port function attribute
before its activated.
When a subfunction is activated, it results in an auxiliary device on
the host PCI device where it is deployed. A driver binds to the
auxiliary device that further creates supported class devices.
example subfunction usage sequence:
-----------------------------------
Change device to switchdev mode:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
Add a devlink port of subfunction flavour:
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
Configure mac address of the port function:
$ devlink port function set ens2f0npf0sf88 hw_addr 00:00:00:00:88:88
Now activate the function:
$ devlink port function set ens2f0npf0sf88 state active
Now use the auxiliary device and class devices:
$ devlink dev show
pci/0000:06:00.0
auxiliary/mlx5_core.sf.4
$ ip link show
127: ens2f0np0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 24:8a:07:b3:d1:12 brd ff:ff:ff:ff:ff:ff
altname enp6s0f0np0
129: p0sf88: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 00:00:00:00:88:88 brd ff:ff:ff:ff:ff:ff
$ rdma dev show
43: rdmap6s0f0: node_type ca fw 16.29.0550 node_guid 248a:0703:00b3:d112 sys_image_guid 248a:0703:00b3:d112
44: mlx5_0: node_type ca fw 16.29.0550 node_guid 0000:00ff:fe00:8888 sys_image_guid 248a:0703:00b3:d112
After use inactivate the function:
$ devlink port function set ens2f0npf0sf88 state inactive
Now delete the subfunction port:
$ devlink port del ens2f0npf0sf88
[1] https://lore.kernel.org/netdev/20200519092258.GF4655@nanopsycho/
[2] https://marc.info/?l=linux-netdev&m=158555928517777&w=2
=================
* tag 'mlx5-updates-2021-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Add devlink subfunction port documentation
devlink: Extend devlink port documentation for subfunctions
devlink: Add devlink port documentation
net/mlx5: SF, Port function state change support
net/mlx5: SF, Add port add delete functionality
net/mlx5: E-switch, Add eswitch helpers for SF vport
net/mlx5: E-switch, Prepare eswitch to handle SF vport
net/mlx5: SF, Add auxiliary device driver
net/mlx5: SF, Add auxiliary device support
net/mlx5: Introduce vhca state event notifier
devlink: Support get and set state of port function
devlink: Support add and delete devlink port
devlink: Introduce PCI SF port flavour and port attribute
devlink: Prepare code to fill multiple port function attributes
====================
Link: https://lore.kernel.org/r/20210122193658.282884-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add packet trap that can report packets that were dropped due to
destination MAC filtering.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch ASIC has a limited capacity of physical ('flavour physical'
in devlink terminology) ports that it can support. While each system is
brought up with a different number of ports, this number can be
increased via splitting up to the ASIC's limit.
Expose physical ports as a devlink resource so that user space will have
visibility to the maximum number of ports that can be supported and the
current occupancy.
In addition, add a "Generic Resources" section in devlink-resource
documentation so the different drivers will be aligned by the same resource
name when exposing to user space.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
devlink port function can be in active or inactive state.
Allow users to get and set port function's state.
When the port function it activated, its operational state may change
after a while when the device is created and driver binds to it.
Similarly on deactivation flow.
To clearly describe the state of the port function and its device's
operational state in the host system, define state and opstate
attributes.
Example of a PCI SF port which supports a port function:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
$ devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0np0 flavour physical port 0 splittable false
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
pci/0000:08:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show pci/0000:06:00.0/32768
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:88:88 state inactive opstate detached
$ devlink port function set pci/0000:06:00.0/32768 hw_addr 00:00:00:00:88:88 state active
$ devlink port show pci/0000:06:00.0/32768 -jp
{
"port": {
"pci/0000:06:00.0/32768": {
"type": "eth",
"netdev": "ens2f0npf0sf88",
"flavour": "pcisf",
"controller": 0,
"pfnum": 0,
"sfnum": 88,
"external": false,
"splittable": false,
"function": {
"hw_addr": "00:00:00:00:88:88",
"state": "active",
"opstate": "attached"
}
}
}
}
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Extended devlink interface for the user to add and delete a port.
Extend devlink to connect user requests to driver to add/delete
a port in the device.
Driver routines are invoked without holding devlink instance lock.
This enables driver to perform several devlink objects registration,
unregistration such as (port, health reporter, resource etc) by using
existing devlink APIs.
This also helps to uniformly use the code for port unregistration
during driver unload and during port deletion initiated by user.
Examples of add, show and delete commands:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
$ devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0np0 flavour physical port 0 splittable false
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
pci/0000:06:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show pci/0000:06:00.0/32768
pci/0000:06:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ udevadm test-builtin net_id /sys/class/net/eth6
Load module index
Parsed configuration file /usr/lib/systemd/network/99-default.link
Created link configuration context.
Using default interface naming scheme 'v245'.
ID_NET_NAMING_SCHEME=v245
ID_NET_NAME_PATH=enp6s0f0npf0sf88
ID_NET_NAME_SLOT=ens2f0npf0sf88
Unload module index
Unloaded link configuration context.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
A PCI sub-function (SF) represents a portion of the device similar
to PCI VF.
In an eswitch, PCI SF may have port which is normally represented
using a representor netdevice.
To have better visibility of eswitch port, its association with SF,
and its representor netdevice, introduce a PCI SF port flavour.
When devlink port flavour is PCI SF, fill up PCI SF attributes of the
port.
Extend port name creation using PCI PF and SF number scheme on best
effort basis, so that vendor drivers can skip defining their own
scheme.
This is done as cApfNSfM, where A, N and M are controller, PCI PF and
PCI SF number respectively.
This is similar to existing naming for PCI PF and PCI VF ports.
An example view of a PCI SF port:
$ devlink port show pci/0000:06:00.0/32768
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:88:88 state active opstate attached
$ devlink port show pci/0000:06:00.0/32768 -jp
{
"port": {
"pci/0000:06:00.0/32768": {
"type": "eth",
"netdev": "ens2f0npf0sf88",
"flavour": "pcisf",
"controller": 0,
"pfnum": 0,
"sfnum": 88,
"splittable": false,
"function": {
"hw_addr": "00:00:00:00:88:88",
"state": "active",
"opstate": "attached"
}
}
}
}
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add a packet trap to report packets that were dropped due to a
blackhole nexthop.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When performing a flash update via devlink, device drivers may inform
user space of status updates via
devlink_flash_update_(begin|end|timeout|status)_notify functions.
It is expected that drivers do not send any status notifications unless
they send a begin and end message. If a driver sends a status
notification without sending the appropriate end notification upon
finishing (regardless of success or failure), the current implementation
of the devlink userspace program can get stuck endlessly waiting for the
end notification that will never come.
The current ice driver implementation may send such a status message
without the appropriate end notification in rare cases.
Fixing the ice driver is relatively simple: we just need to send the
begin_notify at the start of the function and always send an end_notify
no matter how the function exits.
Rather than assuming driver authors will always get this right in the
future, lets just fix the API so that it is not possible to get wrong.
Make devlink_flash_update_begin_notify and
devlink_flash_update_end_notify static, and call them in devlink.c core
code. Always send the begin_notify just before calling the driver's
flash_update routine. Always send the end_notify just after the routine
returns regardless of success or failure.
Doing this makes the status notification easier to use from the driver,
as it no longer needs to worry about catching failures and cleaning up
by calling devlink_flash_update_end_notify. It is now no longer possible
to do the wrong thing in this regard. We also save a couple of lines of
code in each driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All drivers which implement the devlink flash update support, with the
exception of netdevsim, use either request_firmware or
request_firmware_direct to locate the firmware file. Rather than having
each driver do this separately as part of its .flash_update
implementation, perform the request_firmware within net/core/devlink.c
Replace the file_name parameter in the struct devlink_flash_update_params
with a pointer to the fw object.
Use request_firmware rather than request_firmware_direct. Although most
Linux distributions today do not have the fallback mechanism
implemented, only about half the drivers used the _direct request, as
compared to the generic request_firmware. In the event that
a distribution does support the fallback mechanism, the devlink flash
update ought to be able to use it to provide the firmware contents. For
distributions which do not support the fallback userspace mechanism,
there should be essentially no difference between request_firmware and
request_firmware_direct.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The enable_remote_dev_reset devlink param flags that the host admin
allows device resets that can be initiated by other hosts. This
parameter is useful for setups where a device is shared by different
hosts, such as multi-host setup. Once the user set this parameter to
false, the driver should NACK any attempt to reset the device while the
driver is loaded.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add remote reload stats to hold the history of actions performed due
devlink reload commands initiated by remote host. For example, in case
firmware activation with reset finished successfully but was initiated
by remote host.
The function devlink_remote_reload_actions_performed() is exported to
enable drivers update on remote reload actions performed as it was not
initiated by their own devlink instance.
Expose devlink remote reload stats to the user through devlink dev get
command.
Examples:
$ devlink dev show
pci/0000:82:00.0:
stats:
reload:
driver_reinit 2 fw_activate 1 fw_activate_no_reset 0
remote_reload:
driver_reinit 0 fw_activate 0 fw_activate_no_reset 0
pci/0000:82:00.1:
stats:
reload:
driver_reinit 1 fw_activate 0 fw_activate_no_reset 0
remote_reload:
driver_reinit 1 fw_activate 1 fw_activate_no_reset 0
$ devlink dev show -jp
{
"dev": {
"pci/0000:82:00.0": {
"stats": {
"reload": {
"driver_reinit": 2,
"fw_activate": 1,
"fw_activate_no_reset": 0
},
"remote_reload": {
"driver_reinit": 0,
"fw_activate": 0,
"fw_activate_no_reset": 0
}
}
},
"pci/0000:82:00.1": {
"stats": {
"reload": {
"driver_reinit": 1,
"fw_activate": 0,
"fw_activate_no_reset": 0
},
"remote_reload": {
"driver_reinit": 1,
"fw_activate": 1,
"fw_activate_no_reset": 0
}
}
}
}
}
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add reload stats to hold the history per reload action type and limit.
For example, the number of times fw_activate has been performed on this
device since the driver module was added or if the firmware activation
was performed with or without reset.
Add devlink notification on stats update.
Expose devlink reload stats to the user through devlink dev get command.
Examples:
$ devlink dev show
pci/0000:82:00.0:
stats:
reload:
driver_reinit 2 fw_activate 1 fw_activate_no_reset 0
pci/0000:82:00.1:
stats:
reload:
driver_reinit 1 fw_activate 0 fw_activate_no_reset 0
$ devlink dev show -jp
{
"dev": {
"pci/0000:82:00.0": {
"stats": {
"reload": {
"driver_reinit": 2,
"fw_activate": 1,
"fw_activate_no_reset": 0
}
}
},
"pci/0000:82:00.1": {
"stats": {
"reload": {
"driver_reinit": 1,
"fw_activate": 0,
"fw_activate_no_reset": 0
}
}
}
}
}
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add reload limit to demand restrictions on reload actions.
Reload limits supported:
no_reset: No reset allowed, no down time allowed, no link flap and no
configuration is lost.
By default reload limit is unspecified and so no constraints on reload
actions are required.
Some combinations of action and limit are invalid. For example, driver
can not reinitialize its entities without any downtime.
The no_reset reload limit will have usecase in this patchset to
implement restricted fw_activate on mlx5.
Have the uapi parameter of reload limit ready for future support of
multiselection.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add devlink reload action to allow the user to request a specific reload
action. The action parameter is optional, if not specified then devlink
driver re-init action is used (backward compatible).
Note that when required to do firmware activation some drivers may need
to reload the driver. On the other hand some drivers may need to reset
the firmware to reinitialize the driver entities. Therefore, the devlink
reload command returns the actions which were actually performed.
Reload actions supported are:
driver_reinit: driver entities re-initialization, applying devlink-param
and devlink-resource values.
fw_activate: firmware activate.
command examples:
$devlink dev reload pci/0000:82:00.0 action driver_reinit
reload_actions_performed:
driver_reinit
$devlink dev reload pci/0000:82:00.0 action fw_activate
reload_actions_performed:
driver_reinit fw_activate
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow regions to be registered to a devlink port. The same netlink API
is used, but the port index is provided to indicate when a region is a
port region as opposed to a device region.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new devlink callback, .trap_group_action_set(), which can be used
by device drivers which do not support controlling the action (drop,
trap) on each trap but rather on the entire group trap.
If this new callback is populated, it will take precedence over the
.trap_action_set() callback when the user requests a change of all the
traps in a group.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
