Commit Graph

87 Commits

Author SHA1 Message Date
Julian Wiedmann bd706ff8ea net: vlan: suppress "failed to kill vid" warnings
When a real dev unregisters, vlan_device_event() also unregisters all
of its vlan interfaces. For each VID this ends up in __vlan_vid_del(),
which attempts to remove the VID from the real dev's VLAN filter.

But the unregistering real dev might no longer be able to issue the
required IOs, and return an error. Subsequently we raise a noisy warning
msg that is not appropriate for this situation: the real dev is being
torn down anyway, there shouldn't be any worry about cleanly releasing
all of its HW-internal resources.

So to avoid scaring innocent users, suppress this warning when the
failed deletion happens on an unregistering device.
While at it also convert the raw pr_warn() to a more fitting
netdev_warn().

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-17 14:30:54 -08:00
Jiri Pirko 32764c66fa net: 8021q: move vlan offload registrations into vlan_core
Currently, the vlan packet offloads are registered only upon 8021q module
load. However, even without this module loaded, the offloads could be
utilized, for example by openvswitch datapath. As reported by Michael,
that causes 2x to 5x performance improvement, depending on a testcase.

So move the vlan offload registrations into vlan_core and make this
available even without 8021q module loaded.

Reported-by: Michael Shteinbok <michaelsh86@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Michael Shteinbok <michaelsh86@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-16 19:51:08 -08:00
Michał Mirosław 418a976d6c 8021q: use __vlan_hwaccel helpers
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-08 20:45:04 -08:00
Ivan Khoronzhuk 960abf68d2 net: 8021q: vlan_core: allow use list of vlans for real device
It's redundancy for the drivers to hold the list of vlans when
absolutely the same list exists in vlan core. In most cases it's
needed only to traverse the vlan devices, their vids and sync some
settings with h/w, so add API to simplify this.

At least some of these drivers also can benefit:
grep "for_each.*vid" -r drivers/net/ethernet/

drivers/net/ethernet/hisilicon/hns3/hns3_enet.c:
drivers/net/ethernet/synopsys/dwc-xlgmac-hw.c:
drivers/net/ethernet/qlogic/qlge/qlge_main.c:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c:
drivers/net/ethernet/via/via-rhine.c:
drivers/net/ethernet/via/via-velocity.c:
drivers/net/ethernet/intel/igb/igb_main.c:
drivers/net/ethernet/intel/ice/ice_main.c:
drivers/net/ethernet/intel/e1000/e1000_main.c:
drivers/net/ethernet/intel/i40e/i40e_main.c:
drivers/net/ethernet/intel/e1000e/netdev.c:
drivers/net/ethernet/intel/igbvf/netdev.c:
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:
drivers/net/ethernet/intel/ixgb/ixgb_main.c:
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c:
drivers/net/ethernet/amd/xgbe/xgbe-dev.c:
drivers/net/ethernet/emulex/benet/be_main.c:
drivers/net/ethernet/neterion/vxge/vxge-main.c:
drivers/net/ethernet/adaptec/starfire.c:
drivers/net/ethernet/brocade/bna/bnad.c:

Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-08 20:30:58 -08:00
Wei Yongjun eeb0a2a526 vlan: vlan_hw_filter_capable() can be static
Fixes the following sparse warning:

net/8021q/vlan_core.c:168:6: warning:
 symbol 'vlan_hw_filter_capable' was not declared. Should it be static?

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-31 23:20:48 -04:00
Gal Pressman 9daae9bd47 net: Call add/kill vid ndo on vlan filter feature toggling
NETIF_F_HW_VLAN_[CS]TAG_FILTER features require more than just a bit
flip in dev->features in order to keep the driver in a consistent state.
These features notify the driver of each added/removed vlan, but toggling
of vlan-filter does not notify the driver accordingly for each of the
existing vlans.

This patch implements a similar solution to NETIF_F_RX_UDP_TUNNEL_PORT
behavior (which notifies the driver about UDP ports in the same manner
that vids are reported).

Each toggling of the features propagates to the 8021q module, which
iterates over the vlans and call add/kill ndo accordingly.

Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-30 09:58:59 -04:00
Toshiaki Makita cbe7128c4b vlan: Fix out of order vlan headers with reorder header off
With reorder header off, received packets are untagged in skb_vlan_untag()
called from within __netif_receive_skb_core(), and later the tag will be
inserted back in vlan_do_receive().

This caused out of order vlan headers when we create a vlan device on top
of another vlan device, because vlan_do_receive() inserts a tag as the
outermost vlan tag. E.g. the outer tag is first removed in skb_vlan_untag()
and inserted back in vlan_do_receive(), then the inner tag is next removed
and inserted back as the outermost tag.

This patch fixes the behaviour by inserting the inner tag at the right
position.

Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 10:03:47 -04:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Vishakha Narvekar e769fcec6b net: 8021q: skip packets if the vlan is down
If the vlan is down, free the packet instead of proceeding with other
processing, or counting it as received.  If vlan interfaces are used
as slaves for bonding, with arp monitoring for connectivity, if the rx
counter is seen to be incrementing, then the bond device will not
observe that the interface is down.

CC: David S. Miller <davem@davemloft.net>
Signed-off-by: Vishakha Narvekar <Vishakha.Narvekar@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-04 18:16:48 -07:00
Vlad Yasevich 28f9ee22bc vlan: Do not put vlan headers back on bridge and macvlan ports
When a vlan is configured with REORDER_HEADER set to 0, the vlan
header is put back into the packet and makes it appear that
the vlan header is still there even after it's been processed.
This posses a problem for bridge and macvlan ports.  The packets
passed to those device may be forwarded and at the time of the
forward, vlan headers end up being unexpectedly present.

With the patch, we make sure that we do not put the vlan header
back (when REORDER_HEADER is 0) if a bridge or macvlan has
been configured on top of the vlan device.

Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-17 14:38:35 -05:00
Padmanabh Ratnakar 74f2d19caf vlan: Invoke driver vlan hooks only if device is present
NIC drivers mark device as detached during error recovery.
It expects no manangement hooks to be invoked in this state.
Invoke driver vlan hooks only if device is present.

Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-03 11:29:56 -05:00
Jiri Pirko df8a39defa net: rename vlan_tx_* helpers since "tx" is misleading there
The same macros are used for rx as well. So rename it.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-13 17:51:08 -05:00
Vlad Yasevich 0d5501c1c8 net: Always untag vlan-tagged traffic on input.
Currently the functionality to untag traffic on input resides
as part of the vlan module and is build only when VLAN support
is enabled in the kernel.  When VLAN is disabled, the function
vlan_untag() turns into a stub and doesn't really untag the
packets.  This seems to create an interesting interaction
between VMs supporting checksum offloading and some network drivers.

There are some drivers that do not allow the user to change
tx-vlan-offload feature of the driver.  These drivers also seem
to assume that any VLAN-tagged traffic they transmit will
have the vlan information in the vlan_tci and not in the vlan
header already in the skb.  When transmitting skbs that already
have tagged data with partial checksum set, the checksum doesn't
appear to be updated correctly by the card thus resulting in a
failure to establish TCP connections.

The following is a packet trace taken on the receiver where a
sender is a VM with a VLAN configued.  The host VM is running on
doest not have VLAN support and the outging interface on the
host is tg3:
10:12:43.503055 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27243,
offset 0, flags [DF], proto TCP (6), length 60)
    10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x48d9), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294837885 ecr 0,nop,wscale 7], length 0
10:12:44.505556 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27244,
offset 0, flags [DF], proto TCP (6), length 60)
    10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x44ee), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294838888 ecr 0,nop,wscale 7], length 0

This connection finally times out.

I've only access to the TG3 hardware in this configuration thus have
only tested this with TG3 driver.  There are a lot of other drivers
that do not permit user changes to vlan acceleration features, and
I don't know if they all suffere from a similar issue.

The patch attempt to fix this another way.  It moves the vlan header
stipping code out of the vlan module and always builds it into the
kernel network core.  This way, even if vlan is not supported on
a virtualizatoin host, the virtual machines running on top of such
host will still work with VLANs enabled.

CC: Patrick McHardy <kaber@trash.net>
CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-11 12:16:51 -07:00
Li RongQing 916c1689a0 8021q: fix a potential memory leak
skb_cow called in vlan_reorder_header does not free the skb when it failed,
and vlan_reorder_header returns NULL to reset original skb when it is called
in vlan_untag, lead to a memory leak.

Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-21 15:12:13 -07:00
dingtianhong f06c7f9f92 vlan: rename __vlan_find_dev_deep() to __vlan_find_dev_deep_rcu()
The __vlan_find_dev_deep should always called in RCU, according
David's suggestion, rename to __vlan_find_dev_deep_rcu looks more
reasonable.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-12 14:39:13 -04:00
dingtianhong 71e415e44c vlan: make a new function vlan_dev_vlan_proto() and export
The vlan support 2 proto: 802.1q and 802.1ad, so make a new function
called vlan_dev_vlan_proto() which could return the vlan proto for
input dev.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-26 16:41:28 -04:00
dingtianhong be14cc98e9 vlan: use use ether_addr_equal_64bits to instead of ether_addr_equal
Ether_addr_equal_64bits is more efficient than ether_addr_equal, and
can be used when each argument is an array within a structure that
contains at least two bytes of data beyond the array, so it is safe
to use it for vlan, and make sense for fast path.

Cc: Joe Perches <joe@perches.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-09 19:03:51 -04:00
dingtianhong 375f67df28 vlan: slight optimization for vlan_do_receive()
According Joe's suggestion, maybe it'd be faster to add an unlikely to
the test for PCKET_OTHERHOST, so I add it and see whether the performance
could be better, although the differences is so small and negligible, but
it is hard to catch that any lower device would set the skb type to
PACKET_OTHERHOST, so most of time, I think it make sense to add unlikely
for the test.

Cc: Joe Perches <joe@perches.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-09 19:03:51 -04:00
nikolay@redhat.com 0369722f02 vlan: make vlan_dev_real_dev work over stacked vlans
Sometimes we might have stacked vlans on top of each other, and we're
interested in the first non-vlan real device on the path, so transform
vlan_dev_real_dev to go over the stacked vlans and extract the first
non-vlan device.

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-05 12:17:42 -07:00
Eric Dumazet d4b812dea4 vlan: mask vlan prio bits
In commit 48cc32d38a
("vlan: don't deliver frames for unknown vlans to protocols")
Florian made sure we set pkt_type to PACKET_OTHERHOST
if the vlan id is set and we could find a vlan device for this
particular id.

But we also have a problem if prio bits are set.

Steinar reported an issue on a router receiving IPv6 frames with a
vlan tag of 4000 (id 0, prio 2), and tunneled into a sit device,
because skb->vlan_tci is set.

Forwarded frame is completely corrupted : We can see (8100:4000)
being inserted in the middle of IPv6 source address :

16:48:00.780413 IP6 2001:16d8:8100:4000:ee1c:0:9d9:bc87 >
9f94:4d95:2001:67c:29f4::: ICMP6, unknown icmp6 type (0), length 64
       0x0000:  0000 0029 8000 c7c3 7103 0001 a0ae e651
       0x0010:  0000 0000 ccce 0b00 0000 0000 1011 1213
       0x0020:  1415 1617 1819 1a1b 1c1d 1e1f 2021 2223
       0x0030:  2425 2627 2829 2a2b 2c2d 2e2f 3031 3233

It seems we are not really ready to properly cope with this right now.

We can probably do better in future kernels :
vlan_get_ingress_priority() should be a netdev property instead of
a per vlan_dev one.

For stable kernels, lets clear vlan_tci to fix the bugs.

Reported-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-07-18 13:05:23 -07:00
Patrick McHardy cf2c014ade net: vlan: fix memory leak in vlan_info_rcu_free()
The following leak is reported by kmemleak:

[   86.812073] kmemleak: Found object by alias at 0xffff88006ecc76f0
[   86.816019] Pid: 739, comm: kworker/u:1 Not tainted 3.9.0-rc5+ #842
[   86.816019] Call Trace:
[   86.816019]  <IRQ>  [<ffffffff81151c58>] find_and_get_object+0x8c/0xdf
[   86.816019]  [<ffffffff8190e90d>] ? vlan_info_rcu_free+0x33/0x49
[   86.816019]  [<ffffffff81151cbe>] delete_object_full+0x13/0x2f
[   86.816019]  [<ffffffff8194bbb6>] kmemleak_free+0x26/0x45
[   86.816019]  [<ffffffff8113e8c7>] slab_free_hook+0x1e/0x7b
[   86.816019]  [<ffffffff81141c05>] kfree+0xce/0x14b
[   86.816019]  [<ffffffff8190e90d>] vlan_info_rcu_free+0x33/0x49
[   86.816019]  [<ffffffff810d0b0b>] rcu_do_batch+0x261/0x4e7

The reason is that in vlan_info_rcu_free() we don't take the VLAN protocol
into account when iterating over the vlan_devices_array.

Reported-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Tested-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-21 15:55:42 -04:00
Patrick McHardy 8ad227ff89 net: vlan: add 802.1ad support
Add support for 802.1ad VLAN devices. This mainly consists of checking for
ETH_P_8021AD in addition to ETH_P_8021Q in a couple of places and check
offloading capabilities based on the used protocol.

Configuration is done using "ip link":

# ip link add link eth0 eth0.1000 \
	type vlan proto 802.1ad id 1000
# ip link add link eth0.1000 eth0.1000.1000 \
	type vlan proto 802.1q id 1000

52:54:00:12:34:56 > 92:b1:54:28:e4:8c, ethertype 802.1Q (0x8100), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84)
    20.1.0.2 > 20.1.0.1: ICMP echo request, id 3003, seq 8, length 64
92:b1:54:28:e4:8c > 52:54:00:12:34:56, ethertype 802.1Q-QinQ (0x88a8), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 47944, offset 0, flags [none], proto ICMP (1), length 84)
    20.1.0.1 > 20.1.0.2: ICMP echo reply, id 3003, seq 8, length 64

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19 14:46:06 -04:00
Patrick McHardy 86a9bad3ab net: vlan: add protocol argument to packet tagging functions
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19 14:46:06 -04:00
Patrick McHardy 1fd9b1fc31 net: vlan: prepare for 802.1ad support
Make the encapsulation protocol value a property of VLAN devices and change
the device lookup functions to take the protocol value into account.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19 14:45:27 -04:00
Patrick McHardy 80d5c3689b net: vlan: prepare for 802.1ad VLAN filtering offload
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19 14:45:27 -04:00
Patrick McHardy f646968f8f net: vlan: rename NETIF_F_HW_VLAN_* feature flags to NETIF_F_HW_VLAN_CTAG_*
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19 14:45:26 -04:00
Vlad Yasevich 7885198861 bridge: Implement vlan ingress/egress policy with PVID.
At ingress, any untagged traffic is assigned to the PVID.
Any tagged traffic is filtered according to membership bitmap.

At egress, if the vlan matches the PVID, the frame is sent
untagged.  Otherwise the frame is sent tagged.

Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-13 19:42:15 -05:00
Michał Mirosław d2ed273d30 net: disallow drivers with buggy VLAN accel to register_netdevice()
Instead of jumping aroung bugs that are easily fixed just don't let them in:
affected drivers should be either fixed or have NETIF_F_HW_VLAN_FILTER
removed from advertised features.

Quick grep in drivers/net shows two drivers that have NETIF_F_HW_VLAN_FILTER
but not ndo_vlan_rx_add/kill_vid(), but those are false-positives (features
are commented out).

OTOH two drivers have ndo_vlan_rx_add/kill_vid() implemented but don't
advertise NETIF_F_HW_VLAN_FILTER. Those are:

+ethernet/cisco/enic/enic_main.c
+ethernet/qlogic/qlcnic/qlcnic_main.c

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-29 22:58:40 -05:00
Jiri Pirko 1cdfd72f79 vlan: remove usage of dev->master in __vlan_find_dev_deep()
Also, since all users call __vlan_find_dev_deep() with rcu_read_lock,
make no possibility to call this with rtnl mutex held only.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-04 13:31:50 -08:00
Jiri Pirko 55462cf30a vlan: fix bond/team enslave of vlan challenged slave/port
In vlan_uses_dev() check for number of vlan devs rather than existence
of vlan_info. The reason is that vlan id 0 is there without appropriate
vlan dev on it by default which prevented from enslaving vlan challenged
dev.

Reported-by: Jon Stanley <jstanley@rmrf.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-16 14:41:46 -04:00
Florian Zumbiehl 48cc32d38a vlan: don't deliver frames for unknown vlans to protocols
6a32e4f9dd made the vlan code skip marking
vlan-tagged frames for not locally configured vlans as PACKET_OTHERHOST if
there was an rx_handler, as the rx_handler could cause the frame to be received
on a different (virtual) vlan-capable interface where that vlan might be
configured.

As rx_handlers do not necessarily return RX_HANDLER_ANOTHER, this could cause
frames for unknown vlans to be delivered to the protocol stack as if they had
been received untagged.

For example, if an ipv6 router advertisement that's tagged for a locally not
configured vlan is received on an interface with macvlan interfaces attached,
macvlan's rx_handler returns RX_HANDLER_PASS after delivering the frame to the
macvlan interfaces, which caused it to be passed to the protocol stack, leading
to ipv6 addresses for the announced prefix being configured even though those
are completely unusable on the underlying interface.

The fix moves marking as PACKET_OTHERHOST after the rx_handler so the
rx_handler, if there is one, sees the frame unchanged, but afterwards,
before the frame is delivered to the protocol stack, it gets marked whether
there is an rx_handler or not.

Signed-off-by: Florian Zumbiehl <florz@florz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-08 15:21:55 -04:00
Antonio Quartulli 5316cf9a51 8021q: fix mac_len recomputation in vlan_untag()
skb_reset_mac_len() relies on the value of the skb->network_header pointer,
therefore we must wait for such pointer to be recalculated before computing
the new mac_len value.

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-02 22:45:57 -04:00
Jiri Pirko 9b361c13ce vlan: add helper which can be called to see if device is used by vlan
also, remove unused vlan_info definition from header

CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-24 13:46:39 -04:00
Joe Perches 53a2b3a18d 8021q: Convert compare_ether_addr to ether_addr_equal
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.

Done via cocci script:

$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
-	!compare_ether_addr(a, b)
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	compare_ether_addr(a, b)
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) == 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) != 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) == 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) != 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!!ether_addr_equal(a, b)
+	ether_addr_equal(a, b)

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-09 20:49:17 -04:00
Dan Carpenter f9586f79bf vlan: add rtnl_dereference() annotations
The original code generates a Sparse warning:
net/8021q/vlan_core.c:336:9:
	error: incompatible types in comparison expression (different address spaces)

It's ok to dereference __rcu pointers here because we are holding the
RTNL lock.  I've added some calls to rtnl_dereference() to silence the
warning.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-14 02:39:30 -05:00
Jiri Pirko 348a1443cc vlan: introduce functions to do mass addition/deletion of vids by another device
Introduce functions handy to copy vlan ids from one driver's list to
another.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-08 19:52:42 -05:00
Jiri Pirko 5b9ea6e022 vlan: introduce vid list with reference counting
This allows to keep track of vids needed to be in rx vlan filters of
devices even if they are used in bond/team etc.

vlan_info as well as vlan_group previously was, is allocated when first
vid is added and dealocated whan last vid is deleted.

vlan_group definition is moved to private header.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-08 19:52:42 -05:00
Jiri Pirko 87002b03ba net: introduce vlan_vid_[add/del] and use them instead of direct [add/kill]_vid ndo calls
This patch adds wrapper for ndo_vlan_rx_add_vid/ndo_vlan_rx_kill_vid
functions. Check for NETIF_F_HW_VLAN_FILTER feature is done in this
wrapper.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-08 19:52:42 -05:00
Jiri Pirko 7da82c06de vlan: rename vlan_dev_info to vlan_dev_priv
As this structure is priv, name it approprietely. Also for pointer to it
use name "vlan".

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-08 19:51:30 -05:00
Pravin B Shelar 396cf94305 vlan: Move vlan_set_encap_proto() to vlan header file
Open vSwitch needs this function for vlan handling.

Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
2011-12-03 09:35:09 -08:00
Linus Torvalds 32aaeffbd4 Merge branch 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
  Revert "tracing: Include module.h in define_trace.h"
  irq: don't put module.h into irq.h for tracking irqgen modules.
  bluetooth: macroize two small inlines to avoid module.h
  ip_vs.h: fix implicit use of module_get/module_put from module.h
  nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
  include: replace linux/module.h with "struct module" wherever possible
  include: convert various register fcns to macros to avoid include chaining
  crypto.h: remove unused crypto_tfm_alg_modname() inline
  uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
  pm_runtime.h: explicitly requires notifier.h
  linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
  miscdevice.h: fix up implicit use of lists and types
  stop_machine.h: fix implicit use of smp.h for smp_processor_id
  of: fix implicit use of errno.h in include/linux/of.h
  of_platform.h: delete needless include <linux/module.h>
  acpi: remove module.h include from platform/aclinux.h
  miscdevice.h: delete unnecessary inclusion of module.h
  device_cgroup.h: delete needless include <linux/module.h>
  net: sch_generic remove redundant use of <linux/module.h>
  net: inet_timewait_sock doesnt need <linux/module.h>
  ...

Fix up trivial conflicts (other header files, and  removal of the ab3550 mfd driver) in
 - drivers/media/dvb/frontends/dibx000_common.c
 - drivers/media/video/{mt9m111.c,ov6650.c}
 - drivers/mfd/ab3550-core.c
 - include/linux/dmaengine.h
2011-11-06 19:44:47 -08:00
Paul Gortmaker bc3b2d7fb9 net: Add export.h for EXPORT_SYMBOL/THIS_MODULE to non-modules
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:30 -04:00
Eric Dumazet 6a32e4f9dd vlan: allow nested vlan_do_receive()
commit 2425717b27 (net: allow vlan traffic to be received under bond)
broke ARP processing on vlan on top of bonding.

       +-------+
eth0 --| bond0 |---bond0.103
eth1 --|       |
       +-------+

52870.115435: skb_gro_reset_offset <-napi_gro_receive
52870.115435: dev_gro_receive <-napi_gro_receive
52870.115435: napi_skb_finish <-napi_gro_receive
52870.115435: netif_receive_skb <-napi_skb_finish
52870.115435: get_rps_cpu <-netif_receive_skb
52870.115435: __netif_receive_skb <-netif_receive_skb
52870.115436: vlan_do_receive <-__netif_receive_skb
52870.115436: bond_handle_frame <-__netif_receive_skb
52870.115436: vlan_do_receive <-__netif_receive_skb
52870.115436: arp_rcv <-__netif_receive_skb
52870.115436: kfree_skb <-arp_rcv

Packet is dropped in arp_rcv() because its pkt_type was set to
PACKET_OTHERHOST in the first vlan_do_receive() call, since no eth0.103
exists.

We really need to change pkt_type only if no more rx_handler is about to
be called for the packet.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-30 04:43:30 -04:00
Jiri Pirko c5114cd59d vlan: reset headers on accel emulation path
It's after all necessary to do reset headers here. The reason is we
cannot depend that it gets reseted in __netif_receive_skb once skb is
reinjected. For incoming vlanids without vlan_dev, vlan_do_receive()
returns false with skb != NULL and __netif_reveive_skb continues, skb is
not reinjected.

This might be good material for 3.0-stable as well

Reported-by: Mike Auty <mike.auty@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-18 21:29:27 -07:00
Jiri Pirko ffcf9b7672 vlan: kill vlan_gro_frags and vlan_gro_receive
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21 13:47:57 -07:00
Jiri Pirko a4aeb26628 vlan: kill __vlan_hwaccel_rx and vlan_hwaccel_rx
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21 13:47:56 -07:00
Jiri Pirko cec9c13363 vlan: introduce __vlan_find_dev_deep()
Since vlan_group_get_device and vlan_group is not going to be accessible
from device drivers, introduce function which substitutes it.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21 13:47:53 -07:00
Jiri Pirko 0b5c9db1b1 vlan: Fix the ingress VLAN_FLAG_REORDER_HDR check
Testing of VLAN_FLAG_REORDER_HDR does not belong in vlan_untag
but rather in vlan_do_receive.  Otherwise the vlan header
will not be properly put on the packet in the case of
vlan header accelleration.

As we remove the check from vlan_check_reorder_header
rename it vlan_reorder_header to keep the naming clean.

Fix up the skb->pkt_type early so we don't look at the packet
after adding the vlan tag, which guarantees we don't goof
and look at the wrong field.

Use a simple if statement instead of a complicated switch
statement to decided that we need to increment rx_stats
for a multicast packet.

Hopefully at somepoint we will just declare the case where
VLAN_FLAG_REORDER_HDR is cleared as unsupported and remove
the code.  Until then this keeps it working correctly.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-11 16:15:50 -07:00
Jiri Pirko bcc6d47903 net: vlan: make non-hw-accel rx path similar to hw-accel
Now there are 2 paths for rx vlan frames. When rx-vlan-hw-accel is
enabled, skb is untagged by NIC, vlan_tci is set and the skb gets into
vlan code in __netif_receive_skb - vlan_hwaccel_do_receive.

For non-rx-vlan-hw-accel however, tagged skb goes thru whole
__netif_receive_skb, it's untagged in ptype_base hander and reinjected

This incosistency is fixed by this patch. Vlan untagging happens early in
__netif_receive_skb so the rest of code (ptype_all handlers, rx_handlers)
see the skb like it was untagged by hw.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>

v1->v2:
	remove "inline" from vlan_core.c functions
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-12 14:15:19 -07:00
Eric Dumazet 4af429d29b vlan: lockless transmit path
vlan is a stacked device, like tunnels. We should use the lockless
mechanism we are using in tunnels and loopback.

This patch completely removes locking in TX path.

tx stat counters are added into existing percpu stat structure, renamed
from vlan_rx_stats to vlan_pcpu_stats.

Note : this partially reverts commit 2e59af3dcb (vlan: multiqueue vlan
device)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-16 11:15:08 -08:00