This allows to drop the platform_driver's remove function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
A consumer is expected to disable a PWM before calling pwm_put(). And if
they didn't there is hopefully a good reason (or the consumer needs
fixing). Also if disabling an enabled PWM was the right thing to do,
this should better be done in the framework instead of in each low level
driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
With the previous commit there is no need for the lowlevel driver any
more to specify it it uses two or three cells. So simplify accordingly.
The only non-trival change affects the pwm-rockchip driver: It used to only
support three cells if the hardware supports polarity. Now the default
number depends on the device tree which has to match hardware anyhow
(and if it doesn't the error is just a bit delayed as a PWM handle with
an inverted setting is catched when pwm_apply_state() is called).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since commit 5e5da1e9fb ("pwm: ab8500: Explicitly allocate pwm chip
base dynamically") all drivers use dynamic ID allocation explicitly. New
drivers are supposed to do the same, so remove support for driver
specified base IDs and drop all assignments in the low-level drivers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Because period and duty cycle are defined as ints with units of
nanoseconds, the maximum time duration that can be set is limited to
~2.147 seconds. Change their definitions to u64 in the structs of the
PWM framework so that higher durations may be set.
Also use the right format specifiers in debug prints in both core.c,
pwm-stm32-lp.c as well as video/fbdev/ssd1307fb.c.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
LPTimer can use a 32KHz clock for counting. It depends on clock tree
configuration. In such a case, PWM output frequency range is limited.
Although unlikely, nothing prevents user from requesting a PWM frequency
above counting clock (32KHz for instance):
- This causes (prd - 1) = 0xffff to be written in ARR register later in
the apply() routine.
This results in badly configured PWM period (and also duty_cycle).
Add a check to report an error is such a case.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
It is surprising for a PWM consumer when the variable holding the
requested state is modified by pwm_apply_state(). Consider for example a
driver doing:
#define PERIOD 5000000
#define DUTY_LITTLE 10
...
struct pwm_state state = {
.period = PERIOD,
.duty_cycle = DUTY_LITTLE,
.polarity = PWM_POLARITY_NORMAL,
.enabled = true,
};
pwm_apply_state(mypwm, &state);
...
state.duty_cycle = PERIOD / 2;
pwm_apply_state(mypwm, &state);
For sure the second call to pwm_apply_state() should still have
state.period = PERIOD and not something the hardware driver chose for a
reason that doesn't necessarily apply to the second call.
So declare the state argument as a pointer to a const type and adapt all
drivers' .apply callbacks.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add suspend/resume PM sleep ops. When going to low power, enforce the PWM
channel isn't active. Let the PWM consumers disable it during their own
suspend sequence. Only perform a check here, and handle the pinctrl states.
See [1].
[1] https://lkml.org/lkml/2019/2/5/770
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
LPTimer has only one pwm channel (npwm = 1). Remove useless for loop
in remove routine.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add SPDX identifier to make it easier to determine the license of the
file.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The same checking is done by the implementation of pwm_disable().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add support for single PWM channel on Low-Power Timer, that can be
found on some STM32 platforms.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
