[ Upstream commit dc3f595b66 ]
atchan->status variable is used to store two different information:
- pass channel interrupts status from interrupt handler to tasklet;
- channel information like whether it is cyclic or paused;
This causes a bug when device_terminate_all() is called,
(AT_XDMAC_CHAN_IS_CYCLIC cleared on atchan->status) and then a late End
of Block interrupt arrives (AT_XDMAC_CIS_BIS), which sets bit 0 of
atchan->status. Bit 0 is also used for AT_XDMAC_CHAN_IS_CYCLIC, so when
a new descriptor for a cyclic transfer is created, the driver reports
the channel as in use:
if (test_and_set_bit(AT_XDMAC_CHAN_IS_CYCLIC, &atchan->status)) {
dev_err(chan2dev(chan), "channel currently used\n");
return NULL;
}
This patch fixes the bug by adding a different struct member to keep
the interrupts status separated from the channel status bits.
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b14e945bda ]
When initializing clocks, a reference to the TCON channel 0 clock is
obtained. However, the clock is never prepared and enabled later.
Switching from simplefb to DRM actually disables the clock (that was
usually configured by U-Boot) because of that.
On the V3s, this results in a hang when writing to some mixer registers
when switching over to DRM from simplefb.
Fix this by preparing and enabling the clock when initializing other
clocks. Waiting for sun4i_tcon_channel_enable to enable the clock is
apparently too late and results in the same mixer register access hang.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190131132550.26355-1-paul.kocialkowski@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c4cd051ad ]
The map_lookup_elem used to not acquiring spinlock
in order to optimize the reader.
It was true until commit 557c0c6e7d ("bpf: convert stackmap to pre-allocation")
The syscall's map_lookup_elem(stackmap) calls bpf_stackmap_copy().
bpf_stackmap_copy() may find the elem no longer needed after the copy is done.
If that is the case, pcpu_freelist_push() saves this elem for reuse later.
This push requires a spinlock.
If a tracing bpf_prog got run in the middle of the syscall's
map_lookup_elem(stackmap) and this tracing bpf_prog is calling
bpf_get_stackid(stackmap) which also requires the same pcpu_freelist's
spinlock, it may end up with a dead lock situation as reported by
Eric Dumazet in https://patchwork.ozlabs.org/patch/1030266/
The situation is the same as the syscall's map_update_elem() which
needs to acquire the pcpu_freelist's spinlock and could race
with tracing bpf_prog. Hence, this patch fixes it by protecting
bpf_stackmap_copy() with this_cpu_inc(bpf_prog_active)
to prevent tracing bpf_prog from running.
A later syscall's map_lookup_elem commit f1a2e44a3a ("bpf: add queue and stack maps")
also acquires a spinlock and races with tracing bpf_prog similarly.
Hence, this patch is forward looking and protects the majority
of the map lookups. bpf_map_offload_lookup_elem() is the exception
since it is for network bpf_prog only (i.e. never called by tracing
bpf_prog).
Fixes: 557c0c6e7d ("bpf: convert stackmap to pre-allocation")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bb54c4071 ]
Previously, bpf_num_possible_cpus() had a bug when calculating a
number of possible CPUs in the case of sparse CPU allocations, as
it was considering only the first range or element of
/sys/devices/system/cpu/possible.
E.g. in the case of "0,2-3" (CPU 1 is not available), the function
returned 1 instead of 3.
This patch fixes the function by making it parse all CPU ranges and
elements.
Signed-off-by: Martynas Pumputis <m@lambda.lt>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c1cf00eea ]
If create_buf_file() returns an error, don't try to reference it later
as a valid dentry pointer.
This problem was exposed when debugfs started to return errors instead
of just NULL for some calls when they do not succeed properly.
Also, the check for WARN_ON(dentry) was just wrong :)
Reported-by: Kees Cook <keescook@chromium.org>
Reported-and-tested-by: syzbot+16c3a70e1e9b29346c43@syzkaller.appspotmail.com
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Fixes: ff9fb72bc0 ("debugfs: return error values, not NULL")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56841070cc ]
According to ARM IHI 0069C (ID070116), we should use GITS_TYPER's
bits [7:4] as ITT_entry_size instead of [8:4]. Although this is
pretty annoying, it only results in a potential over-allocation
of memory, and nothing bad happens.
Fixes: 3dfa576bfb ("irqchip/gic-v3-its: Add probing for VLPI properties")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
[maz: massaged subject and commit message]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2cd682deb ]
In stmmac xmit callback we use a different flow for TSO packets but TSO
xmit callback is not disabling the EEE mode.
Fix this by disabling earlier the EEE mode, i.e. before calling the TSO
xmit callback.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5acdbee22 ]
The number of TSO enabled channels in HW can be different than the
number of total channels. There is no way to determined, at runtime, the
number of TSO capable channels and its safe to assume that if TSO is
enabled then at least channel 0 will be TSO capable.
Lets always send TSO packets from Queue 0.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ec5302fa9 ]
If we don't have DT then stmmac_clk will not be available. Let's add a
new Platform Data field so that we can specify the refclk by this mean.
This way we can still use the coalesce command in PCI based setups.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e11ea9de9 ]
amdgpu only uses shared-fences internally, but dmabuf importers rely on
implicit write hazard tracking via the reservation_object.fence_excl.
For example, the importer use the write hazard for timing a page flip to
only occur after the exporter has finished flushing its write into the
surface. As such, on exporting a dmabuf, we must either flush all
outstanding fences (for we do not know which are writes and should have
been exclusive) or alternatively create a new exclusive fence that is
the composite of all the existing shared fences, and so will only be
signaled when all earlier fences are signaled (ensuring that we can not
be signaled before the completion of any earlier write).
v2: reservation_object is already locked by amdgpu_bo_reserve()
v3: Replace looping with get_fences_rcu and special case the promotion
of a single shared fence directly to an exclusive fence, bypassing the
fence array.
v4: Drop the fence array ref after assigning to reservation_object
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107341
Testcase: igt/amd_prime/amd-to-i915
References: 8e94a46c17 ("drm/amdgpu: Attach exclusive fence to prime exported bo's. (v5)")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Reviewed-by: "Christian König" <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afeff4c16e ]
Check if the device is root rather before attempting to see what
speeds the pcie port supports. Fixes a crash with pci passthrough
in a VM.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=109366
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc14eb12f6 ]
Add missing power_average to visible check for power
attributes for APUs. Was missed before.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2380a22b60 ]
Resetting bit 4 disables the interrupt delivery to the "secure
processor" core. This breaks the keyboard on a OLPC XO 1.75 laptop,
where the firmware running on the "secure processor" bit-bangs the
PS/2 protocol over the GPIO lines.
It is not clear what the rest of the bits are and Marvell was unhelpful
when asked for documentation. Aside from the SP bit, there are probably
priority bits.
Leaving the unknown bits as the firmware set them up seems to be a wiser
course of action compared to just turning them off.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
[maz: fixed-up subject and commit message]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45725e0fc3 ]
In the unlikely event that we cannot find any available LPI in the
system, we should gracefully return an error instead of carrying
on with no LPI allocated at all.
Fixes: 38dd7c494c ("irqchip/gic-v3-its: Drop chunk allocation compatibility")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6479450f72 ]
1. In current implementation, every VLPI will temporarily be mapped to
the first CPU in system (normally CPU0) and then moved to the real
scheduled CPU later.
2. So there is a time window and a VLPI may be sent to CPU0 instead of
the real scheduled vCPU, in a multi-CPU virtual machine.
3. However, CPU0 may have not been scheduled as a virtual CPU after
system boots up, so the value of its GICR_VPROPBASER is unknown at
that moment.
4. If the INTID of VLPI is larger than 2^(GICR_VPROPBASER.IDbits+1),
while IDbits is also in unknown state, GIC will behave as if the VLPI
is out of range and simply drop it, which results in interrupt missing
in Guest.
As no code will clear GICR_VPROPBASER at runtime, we can safely
initialize the IDbits field at boot time for each CPU to get rid of
this issue.
We also clear Valid bit of GICR_VPENDBASER in case any ancient
programming gets left in and causes memory corrupting. A new function
its_clear_vpend_valid() is added to reuse the code in
its_vpe_deschedule().
Fixes: e643d80340 ("irqchip/gic-v3-its: Add VPE scheduling")
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2105d4259 ]
Fix link errors when CONFIG_FSL_USB2_OTG is enabled and USB_OTG_FSM is
set to module then the following link error occurs.
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_ioctl':
drivers/usb/phy/phy-fsl-usb.c:1083: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:1083:(.text+0x574): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_start_srp':
drivers/usb/phy/phy-fsl-usb.c:674: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:674:(.text+0x61c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_set_host':
drivers/usb/phy/phy-fsl-usb.c:593: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:593:(.text+0x7a4): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_start_hnp':
drivers/usb/phy/phy-fsl-usb.c:695: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:695:(.text+0x858): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `a_wait_enum':
drivers/usb/phy/phy-fsl-usb.c:274: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:274:(.text+0x16f0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o:drivers/usb/phy/phy-fsl-usb.c:619: more undefined references to `otg_statemachine' follow
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_set_peripheral':
drivers/usb/phy/phy-fsl-usb.c:619:(.text+0x1fa0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
make[1]: *** [Makefile:1020: vmlinux] Error 1
make[1]: Target 'Image' not remade because of errors.
make: *** [Makefile:152: sub-make] Error 2
make: Target 'Image' not remade because of errors.
Rework so that FSL_USB2_OTG depends on that the USB_OTG_FSM is builtin.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d652669b6 ]
With the addition of TXQ stats in the per-tid statistics the struct
station_info grew significantly. This resulted in stack size warnings
due to the structure itself being above the limit for the warnings.
To work around this, the TID array was allocated dynamically. Also a
function to free this content was introduced with commit 7ea3e110f2
("cfg80211: release station info tidstats where needed") but the necessary
changes were not provided for batman-adv's B.A.T.M.A.N. V implementation.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes: 8689c051a2 ("cfg80211: dynamically allocate per-tid stats for station info")
[sven@narfation.org: add commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a81efb0de ]
Add compatible to gicv3 node to enable quirk required to restrict writing
to GICR_WAKER register which is restricted on msm8996 SoC in Hypervisor.
With this quirk MSM8996 can at least boot out of mainline, which can help
community to work with boards based on MSM8996.
Without this patch Qualcomm DB820c board reboots on mainline.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba16adeb34 ]
devm_ allocated data will be automatically freed. The free
of devm_ allocated data is invalid.
Fixes: 1c459de1e6 ("ARM: pxa: ssp: use devm_ functions")
Signed-off-by: Peng Hao <peng.hao2@zte.com.cn>
[title's prefix changed]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9e4576743 ]
When sock recvbuff is set by bpf_setsockopt(), the value must by
limited by rmem_max. It is the same with sendbuff.
Fixes: 8c4b4c7e9f ("bpf: Add setsockopt helper function to bpf")
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0ca5ecb8e ]
When updating a percpu map, bpftool currently copies the provided
value only into the first per CPU copy of the specified value,
all others instances are left zeroed.
This change explicitly copies the user-provided bytes to all the
per CPU instances, keeping the sub-command syntax unchanged.
v2 -> v3:
- drop unused argument, as per Quentin's suggestion
v1 -> v2:
- rename the helper as per Quentin's suggestion
Fixes: 71bb428fe2 ("tools: bpf: add bpftool")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 752bcf80f5 ]
Lance reported an issue with bpftool not being able to
dump program if there are more programs loaded and you
want to dump any but the first program, like:
# bpftool prog
28: kprobe name trace_req_start tag 1dfc28ba8b3dd597 gpl
loaded_at 2019-01-18T17:02:40+1100 uid 0
xlated 112B jited 109B memlock 4096B map_ids 13
29: kprobe name trace_req_compl tag 5b6a5ecc6030a683 gpl
loaded_at 2019-01-18T17:02:40+1100 uid 0
xlated 928B jited 575B memlock 4096B map_ids 13,14
# bpftool prog dum jited tag 1dfc28ba8b3dd597
0: push %rbp
1: mov %rsp,%rbp
...
# bpftool prog dum jited tag 5b6a5ecc6030a683
Error: can't get prog info (29): Bad address
The problem is in the prog_fd_by_tag function not cleaning
the struct bpf_prog_info before another request, so the
previous program length is still in there and kernel assumes
it needs to dump the program, which fails because there's no
user pointer set.
Moving the struct bpf_prog_info declaration into the loop,
so it gets cleaned before each query.
Fixes: 71bb428fe2 ("tools: bpf: add bpftool")
Reported-by: Lance Digby <ldigby@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13e62626c5 ]
During "wlan-up", we are programming the FW into the WiFi-chip. However,
re-programming the FW doesn't work, unless a power cycle of the WiFi-chip
is made in-between the programmings.
To conform to this requirement and to fix the regression in a simple way,
let's start by allowing that the SDIO card (WiFi-chip) may stay powered on
(runtime resumed) when wl12xx_sdio_power_off() returns. The intent with the
current code is to treat this scenario as an error, but unfortunate this
doesn't work as expected, so let's fix this.
The other part is to guarantee that a power cycle of the SDIO card has been
completed when wl12xx_sdio_power_on() returns, as to allow the FW
programming to succeed. However, relying solely on runtime PM to deal with
this isn't sufficient. For example, userspace may prevent runtime suspend
via sysfs for the device that represents the SDIO card, leading to that the
mmc core also keeps it powered on. For this reason, let's instead do a
brute force power cycle in wl12xx_sdio_power_on().
Fixes: 728a9dc61f ("wlcore: sdio: Fix flakey SDIO runtime PM handling")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f165988b77 ]
Fixes issue created by 9b3e420766.
It wasn't possible for one_regmap_config to be non-NULL at the point
it was tested for mcp23s18 devices.
Applied the same pattern of allocating one_regmap_config using
devm_kmemdump() and then initializing the local regmap structure
from that.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89857a8a5c ]
By clearing all interrupt sources, not only those that
already occurred, the existing code may acknowledge by
mistake interrupts that occurred after the code checks
for them.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05c8478abd ]
SCIF2 on R-Car M3-N can be used with both DMAC1 and DMAC2.
Fixes: 0ea5b2fd38 ("arm64: dts: renesas: r8a77965: Add SCIF device nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97f26702bc ]
SCIF2 on R-Car M3-W can be used with both DMAC1 and DMAC2.
Fixes: dbcae5ea4b ("arm64: dts: r8a7796: Enable SCIF DMA")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba0f456052 ]
i.MX6SX has same GPT type as i.MX6DL, in GPT driver, it uses
below TIMER_OF_DECLARE, so the backward compatible should be
"fsl,imx6dl-gpt", correct it.
TIMER_OF_DECLARE(imx6sx_timer, "fsl,imx6sx-gpt", imx6dl_timer_init_dt);
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8615f55963 ]
After commit 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device
tree") SD cards are not detected anymore.
The CD GPIO is "active low" on the MXIII-Plus. The MMC dt-bindings
specify: "[...] using the "cd-inverted" property means, that the CD line
is active high, i.e. it is high, when a card is inserted".
Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and
drop the "cd-inverted" property. This makes the definition consistent
with the existing dt-bindings and fixes the check whether an SD card is
inserted.
Fixes: 35ee52bea6 ("ARM: dts: meson8m2: add support for the Tronsmart MXIII Plus")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fb348e030 ]
After commit 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device
tree") SD cards are not detected anymore.
The CD GPIO is "active low" on Odroid-C1. The MMC dt-bindings specify:
"[...] using the "cd-inverted" property means, that the CD line is active
high, i.e. it is high, when a card is inserted".
Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and
drop the "cd-inverted" property. This makes the definition consistent
with the existing dt-bindings and fixes the check whether an SD card is
inserted.
Fixes: e03efbce6b ("ARM: dts: meson8b-odroidc1: add microSD support")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e35e26b26e ]
A long running stress test on a custom board shipping an AXG SoCs and a
Realtek RTL8211F PHY revealed that after a few hours the connection
speed would drop drastically, from ~1000Mbps to ~3Mbps. At the same time
the 'macirq' (eth0) IRQ would stop being triggered at all and as
consequence the GMAC IRQs never ACKed.
After a painful investigation the problem seemed to be due to a wrong
defined IRQ type for the GMAC IRQ that should be LEVEL_HIGH instead of
EDGE_RISING.
The change in the macirq IRQ type also solved another long standing
issue affecting this SoC/PHY where EEE was causing the network
connection to die after stressing it with iperf3 (even though much
sooner). It's now possible to remove the 'eee-broken-1000t' quirk as
well.
Fixes: 9c15795a4f ("ARM: dts: meson8b-odroidc1: ethernet support")
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc4bddade1 ]
Because "ethernet0" alias is missing, U-Boot doesn't generate board
specific MAC address. Effect of this is random MAC address every boot
and thus new IP address is assigned to the board.
Fix this by adding alias.
Fixes: 7389172fc3 ("ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[Maxime: Removed unneeded comment]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef4a55b919 ]
We're now getting the following error:
genirq: Setting trigger mode 1 for irq 230 failed
(regmap_irq_set_type+0x0/0x15c)
cpcap-usb-phy cpcap-usb-phy.0: could not get irq dp: -524
Cc: Sebastian Reichel <sre@kernel.org>
Reported-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8443e4843e ]
Commit a758f50f10 ("mtd: onenand: omap2: Configure driver from DT")
started using DT specified timings for GPMC, and as a result the
OneNAND stopped working on N950/N9 as we had wrong values in the DT.
Fix by updating the values to bootloader timings that have been tested
to be working on both Nokia N950 and N9.
Fixes: a758f50f10 ("mtd: onenand: omap2: Configure driver from DT")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 891cb2a72d ]
Rong Chen has reported the following boot crash:
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 1 PID: 239 Comm: udevd Not tainted 5.0.0-rc4-00149-gefad4e4 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
RIP: 0010:page_mapping+0x12/0x80
Code: 5d c3 48 89 df e8 0e ad 02 00 85 c0 75 da 89 e8 5b 5d c3 0f 1f 44 00 00 53 48 89 fb 48 8b 43 08 48 8d 50 ff a8 01 48 0f 45 da <48> 8b 53 08 48 8d 42 ff 83 e2 01 48 0f 44 c3 48 83 38 ff 74 2f 48
RSP: 0018:ffff88801fa87cd8 EFLAGS: 00010202
RAX: ffffffffffffffff RBX: fffffffffffffffe RCX: 000000000000000a
RDX: fffffffffffffffe RSI: ffffffff820b9a20 RDI: ffff88801e5c0000
RBP: 6db6db6db6db6db7 R08: ffff88801e8bb000 R09: 0000000001b64d13
R10: ffff88801fa87cf8 R11: 0000000000000001 R12: ffff88801e640000
R13: ffffffff820b9a20 R14: ffff88801f145258 R15: 0000000000000001
FS: 00007fb2079817c0(0000) GS:ffff88801dd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000006 CR3: 000000001fa82000 CR4: 00000000000006a0
Call Trace:
__dump_page+0x14/0x2c0
is_mem_section_removable+0x24c/0x2c0
removable_show+0x87/0xa0
dev_attr_show+0x25/0x60
sysfs_kf_seq_show+0xba/0x110
seq_read+0x196/0x3f0
__vfs_read+0x34/0x180
vfs_read+0xa0/0x150
ksys_read+0x44/0xb0
do_syscall_64+0x5e/0x4a0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
and bisected it down to commit efad4e475c ("mm, memory_hotplug:
is_mem_section_removable do not pass the end of a zone").
The reason for the crash is that the mapping is garbage for poisoned
(uninitialized) page. This shouldn't happen as all pages in the zone's
boundary should be initialized.
Later debugging revealed that the actual problem is an off-by-one when
evaluating the end_page. 'start_pfn + nr_pages' resp 'zone_end_pfn'
refers to a pfn after the range and as such it might belong to a
differen memory section.
This along with CONFIG_SPARSEMEM then makes the loop condition
completely bogus because a pointer arithmetic doesn't work for pages
from two different sections in that memory model.
Fix the issue by reworking is_pageblock_removable to be pfn based and
only use struct page where necessary. This makes the code slightly
easier to follow and we will remove the problematic pointer arithmetic
completely.
Link: http://lkml.kernel.org/r/20190218181544.14616-1-mhocko@kernel.org
Fixes: efad4e475c ("mm, memory_hotplug: is_mem_section_removable do not pass the end of a zone")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: <rong.a.chen@intel.com>
Tested-by: <rong.a.chen@intel.com>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f585b283e3 ]
In autofs_fill_super() on error of get inode/make root dentry the return
should be ENOMEM as this is the only failure case of the called
functions.
Link: http://lkml.kernel.org/r/154725123240.11260.796773942606871359.stgit@pluto-themaw-net
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63ce5f552b ]
autofs_expire_run() calls dput(dentry) to drop the reference count of
dentry. However, dentry is read via autofs_dentry_ino(dentry) after
that. This may result in a use-free-bug. The patch drops the reference
count of dentry only when it is never used.
Link: http://lkml.kernel.org/r/154725122396.11260.16053424107144453867.stgit@pluto-themaw-net
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c27d82f52f ]
When superblock has lots of inodes without any pagecache (like is the
case for /proc), drop_pagecache_sb() will iterate through all of them
without dropping sb->s_inode_list_lock which can lead to softlockups
(one of our customers hit this).
Fix the problem by going to the slow path and doing cond_resched() in
case the process needs rescheduling.
Link: http://lkml.kernel.org/r/20190114085343.15011-1-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db7ddeab3c ]
There is a copy and paste bug so we set "config->test_driver" to NULL
twice instead of setting "config->test_fs". Smatch complains that it
leads to a double free:
lib/test_kmod.c:840 __kmod_config_init() warn: 'config->test_fs' double freed
Link: http://lkml.kernel.org/r/20190121140011.GA14283@kadam
Fixes: d9c6a72d6f ("kmod: add test driver to stress test the module loader")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24feb47c5f ]
If memory end is not aligned with the sparse memory section boundary,
the mapping of such a section is only partly initialized. This may lead
to VM_BUG_ON due to uninitialized struct pages access from
test_pages_in_a_zone() function triggered by memory_hotplug sysfs
handlers.
Here are the the panic examples:
CONFIG_DEBUG_VM_PGFLAGS=y
kernel parameter mem=2050M
--------------------------
page:000003d082008000 is uninitialized and poisoned
page dumped because: VM_BUG_ON_PAGE(PagePoisoned(p))
Call Trace:
test_pages_in_a_zone+0xde/0x160
show_valid_zones+0x5c/0x190
dev_attr_show+0x34/0x70
sysfs_kf_seq_show+0xc8/0x148
seq_read+0x204/0x480
__vfs_read+0x32/0x178
vfs_read+0x82/0x138
ksys_read+0x5a/0xb0
system_call+0xdc/0x2d8
Last Breaking-Event-Address:
test_pages_in_a_zone+0xde/0x160
Kernel panic - not syncing: Fatal exception: panic_on_oops
Fix this by checking whether the pfn to check is within the zone.
[mhocko@suse.com: separated this change from http://lkml.kernel.org/r/20181105150401.97287-2-zaslonko@linux.ibm.com]
Link: http://lkml.kernel.org/r/20190128144506.15603-3-mhocko@kernel.org
[mhocko@suse.com: separated this change from
http://lkml.kernel.org/r/20181105150401.97287-2-zaslonko@linux.ibm.com]
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Tested-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efad4e475c ]
Patch series "mm, memory_hotplug: fix uninitialized pages fallouts", v2.
Mikhail Zaslonko has posted fixes for the two bugs quite some time ago
[1]. I have pushed back on those fixes because I believed that it is
much better to plug the problem at the initialization time rather than
play whack-a-mole all over the hotplug code and find all the places
which expect the full memory section to be initialized.
We have ended up with commit 2830bf6f05 ("mm, memory_hotplug:
initialize struct pages for the full memory section") merged and cause a
regression [2][3]. The reason is that there might be memory layouts
when two NUMA nodes share the same memory section so the merged fix is
simply incorrect.
In order to plug this hole we really have to be zone range aware in
those handlers. I have split up the original patch into two. One is
unchanged (patch 2) and I took a different approach for `removable'
crash.
[1] http://lkml.kernel.org/r/20181105150401.97287-2-zaslonko@linux.ibm.com
[2] https://bugzilla.redhat.com/show_bug.cgi?id=1666948
[3] http://lkml.kernel.org/r/20190125163938.GA20411@dhcp22.suse.cz
This patch (of 2):
Mikhail has reported the following VM_BUG_ON triggered when reading sysfs
removable state of a memory block:
page:000003d08300c000 is uninitialized and poisoned
page dumped because: VM_BUG_ON_PAGE(PagePoisoned(p))
Call Trace:
is_mem_section_removable+0xb4/0x190
show_mem_removable+0x9a/0xd8
dev_attr_show+0x34/0x70
sysfs_kf_seq_show+0xc8/0x148
seq_read+0x204/0x480
__vfs_read+0x32/0x178
vfs_read+0x82/0x138
ksys_read+0x5a/0xb0
system_call+0xdc/0x2d8
Last Breaking-Event-Address:
is_mem_section_removable+0xb4/0x190
Kernel panic - not syncing: Fatal exception: panic_on_oops
The reason is that the memory block spans the zone boundary and we are
stumbling over an unitialized struct page. Fix this by enforcing zone
range in is_mem_section_removable so that we never run away from a zone.
Link: http://lkml.kernel.org/r/20190128144506.15603-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Debugged-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Tested-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8e911d135 ]
If the kernel is configured with KASAN_EXTRA, the stack size is
increasted significantly because this option sets "-fstack-reuse" to
"none" in GCC [1]. As a result, it triggers stack overrun quite often
with 32k stack size compiled using GCC 8. For example, this reproducer
https://github.com/linux-test-project/ltp/blob/master/testcases/kernel/syscalls/madvise/madvise06.c
triggers a "corrupted stack end detected inside scheduler" very reliably
with CONFIG_SCHED_STACK_END_CHECK enabled.
There are just too many functions that could have a large stack with
KASAN_EXTRA due to large local variables that have been called over and
over again without being able to reuse the stacks. Some noticiable ones
are
size
7648 shrink_page_list
3584 xfs_rmap_convert
3312 migrate_page_move_mapping
3312 dev_ethtool
3200 migrate_misplaced_transhuge_page
3168 copy_process
There are other 49 functions are over 2k in size while compiling kernel
with "-Wframe-larger-than=" even with a related minimal config on this
machine. Hence, it is too much work to change Makefiles for each object
to compile without "-fsanitize-address-use-after-scope" individually.
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715#c23
Although there is a patch in GCC 9 to help the situation, GCC 9 probably
won't be released in a few months and then it probably take another
6-month to 1-year for all major distros to include it as a default.
Hence, the stack usage with KASAN_EXTRA can be revisited again in 2020
when GCC 9 is everywhere. Until then, this patch will help users avoid
stack overrun.
This has already been fixed for arm64 for the same reason via
6e8830674e ("arm64: kasan: Increase stack size for KASAN_EXTRA").
Link: http://lkml.kernel.org/r/20190109215209.2903-1-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6d478aee0 ]
aa_label_merge() can return NULL for memory allocations failures
make sure to handle and set the correct error in this case.
Reported-by: Peng Hao <peng.hao2@zte.com.cn>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2b3d8566d ]
On systems with VHE the kernel and KVM's world-switch code run at the
same exception level. Code that is only used on a VHE system does not
need to be annotated as __hyp_text as it can reside anywhere in the
kernel text.
__hyp_text was also used to prevent kprobes from patching breakpoint
instructions into this region, as this code runs at a different
exception level. While this is no longer true with VHE, KVM still
switches VBAR_EL1, meaning a kprobe's breakpoint executed in the
world-switch code will cause a hyp-panic.
Move the __hyp_text check in the kprobes blacklist so it applies on
VHE systems too, to cover the common code and guest enter/exit
assembly.
Fixes: 888b3c8720 ("arm64: Treat all entry code as non-kprobe-able")
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 912139cfbf ]
The load_microcode_amd() function searches for microcode patches and
attempts to apply a microcode patch if it is of different level than the
currently installed level.
While the processor won't actually load a level that is less than
what is already installed, the logic wrongly returns UCODE_NEW thus
signaling to its caller reload_store() that a late loading should be
attempted.
If the file-system contains an older microcode revision than what is
currently running, such a late microcode reload can result in these
misleading messages:
x86/CPU: CPU features have changed after loading microcode, but might not take effect.
x86/CPU: Please consider either early loading through initrd/built-in or a potential BIOS update.
These messages were issued on a system where SME/SEV are not
enabled by the BIOS (MSR C001_0010[23] = 0b) because during boot,
early_detect_mem_encrypt() is called and cleared the SME and SEV
features in this case.
However, after the wrong late load attempt, get_cpu_cap() is called and
reloads the SME and SEV feature bits, resulting in the messages.
Update the microcode level check to not attempt microcode loading if the
current level is greater than(!) and not only equal to the current patch
level.
[ bp: massage commit message. ]
Fixes: 2613f36ed9 ("x86/microcode: Attempt late loading only when new microcode is present")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/154894518427.9406.8246222496874202773.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Sasha Levin <sashal@kernel.org>