CC [M] drivers/net/ixgbe/ixgbe_main.o
drivers/net/ixgbe/ixgbe_main.c: In function `ixgbe_intr':
drivers/net/ixgbe/ixgbe_main.c:1290: sorry, unimplemented: inlining failed in call to 'ixgbe_irq_enable': function body not available
drivers/net/ixgbe/ixgbe_main.c:1312: sorry, unimplemented: called from here
make[4]: *** [drivers/net/ixgbe/ixgbe_main.o] Error 1
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So I dug deeper into the DMA problems I had with iwlagn and a kind soul
helped me in that he said something about pci-e alignment and mentioned
the iwl_rx_allocate function to check for crossing 4KB boundaries. Since
there's 8KB A-MPDU support, crossing 4k boundaries didn't seem like
something the device would fail with, but when I looked into the
function for a minute anyway I stumbled over this little gem:
BUG_ON(rxb->dma_addr & (~DMA_BIT_MASK(36) & 0xff));
Clearly, that is a totally bogus check, one would hope the compiler
removes it entirely. (Think about it)
After fixing it, I obviously ran into it, nothing guarantees the
alignment the way you want it, because of the way skbs and their
headroom are allocated. I won't explain that here nor double-check that
I'm right, that goes beyond what most of the CC'ed people care about.
So then I came up with the patch below, and so far my system has
survived minutes with 64K pages, when it would previously fail in
seconds. And I haven't seen a single instance of the TX bug either. But
when you see the patch it'll be pretty obvious to you why.
This should fix the following reported kernel bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=11596http://bugzilla.kernel.org/show_bug.cgi?id=11393http://bugzilla.kernel.org/show_bug.cgi?id=11983
I haven't checked if there are any elsewhere, but I suppose RHBZ will
have a few instances too...
I'd like to ask anyone who is CC'ed (those are people I know ran into
the bug) to try this patch.
I am convinced that this patch is correct in spirit, but I haven't
understood why, for example, there are so many unmap calls. I'm not
entirely convinced that this is the only bug leading to the TX reply
errors.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before ieee80211_notify_mac() was added, it was presented with the
use case of using it to tell mac80211 that the association may
have been lost because the firmware crashed/reset.
Since then, it has also been used by iwlwifi to (slightly) speed
up re-association after resume, a workaround around the fact that
mac80211 has no suspend/resume handling yet. It is also not used
by any other drivers, so clearly it cannot be necessary for "good
enough" suspend/resume.
Unfortunately, the callback suffers from a severe problem: It only
works for station mode. If suspend/resume happens while in IBSS or
any other mode (but station), then the callback is pointless.
Recently, it has created a number of locking issues, first because
it required rtnl locking rather than RCU due to calling sleeping
functions within the critical section, and now because it's called
by iwlwifi from the mac80211 workqueue that may not use the rtnl
because it is flushed under rtnl.
(cf. http://bugzilla.kernel.org/show_bug.cgi?id=12046)
I think, therefore, that we should take a step back, remove it
entirely for now and add the small feature it provided properly.
For suspend and resume we will need to introduce new hooks, and for
the case where the firmware was reset the driver will probably
simply just pretend it has done a suspend/resume cycle to get
mac80211 to reprogram the hardware completely, not just try to
connect to the current AP again in station mode. When doing so, we
will need to take into account locking issues and possibly defer
to schedule_work from within mac80211 for the resume operation,
while the suspend operation must be done directly.
Proper suspend/resume should also not necessarily try to reconnect
to the current AP, the time spent in suspend may have been short
enough to not be disconnected from the AP, mac80211 will detect
that the AP went out of range quickly if it did, and if the
association is lost then the AP will disassoc as soon as a data
frame is sent. We might also take into account WWOL then, and
have mac80211 program the hardware into such a mode where it is
available and requested.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
skb->tail can't be meant here because it's not the same across 32/64 bit
compilations. This means there's no way the current driver can work on
64-bit architectures.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.27]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
rtnetlink: propagate error from dev_change_flags in do_setlink()
isdn: remove extra byteswap in isdn_net_ciscohdlck_slarp_send_reply
Phonet: refuse to send bigger than MTU packets
e1000e: fix IPMI traffic
e1000e: fix warn_on reload after phy_id error
phy: fix phy address bug
e100: fix dma error in direction for mapping
igb: use dev_printk instead of printk
qla3xxx: Cleanup: Fix link print statements.
igb: Use device_set_wakeup_enable
e1000: Use device_set_wakeup_enable
e1000e: Use device_set_wakeup_enable
via-velocity: enable perfect filtering for multicast packets
phy: Add support for Marvell 88E1118 PHY
mlx4_en: Pause parameters per port
phylib: fix premature freeing of struct mii_bus
atl1: Do not enumerate options unsupported by chip
atl1e: fix broken multicast by removing unnecessary crc inversion
gianfar: Fix DMA unmap invocations
net/ucc_geth: Fix oops in uec_get_ethtool_stats()
...
Some users reported that they have machines with BMCs enabled that cannot
receive IPMI traffic after e1000e is loaded.
http://marc.info/?l=e1000-devel&m=121909039127414&w=2http://marc.info/?l=e1000-devel&m=121365543823387&w=2
This fixes the issue if they load with the new parameter = 0 by disabling
crc stripping, but leaves the performance feature on for most users.
Based on work done by Hong Zhang.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver fails to initialize the first time due to the failure in the
phy_id check the kernel triggers a warn_on on the second try to load the
driver because the driver did not free the msi/x resources in the first
load because of the previous failure in phy_id check.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYID returns 0xffff and not 0xffffffff when not found and in some
case(at91sam9263) 0x0. Maybe this patch could be useful.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The e100 driver triggers BUG_ON(buf->direction != dir)
by doing pci_map_single(..., PCI_DMA_BIDIRECTIONAL)
and pci_dma_sync_single_for_device(..., PCI_DMA_TODEVICE).
Changing the DMA direction, especially with dmabounce will result
in unexpected behaviour.
Reported-by: Anders Grafstrom <grfstrm@users.sourceforge.net>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_printk() instead of printk() to give a little more context
and use consistent format.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed debug print statements and improved conditionals around informational statements.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
igb_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add support for the Marvell 88E1118 PHY which supports gigabit ethernet among other things.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the change the driver reported the same pause parameters
for all the ports, even only one of them was modified.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 46abc02175 ("phylib: give mdio
buses a device tree presence") added a call to device_unregister() in
a situation where the caller did not intend for the device to be
freed yet, but apart from just unregistering the device from the
system, device_unregister() does an additional put_device() that is
intended to free it.
The right function to use in this situation is device_del(), which
unregisters the device from the system like device_unregister() does,
but without dropping the reference count an additional time.
Bug report from Bryan Wu <cooloney@kernel.org>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Of the various WOL options provided in include/linux/ethtool.h, the
L1 NIC supports only magic packet. Remove all options except magic
packet from the atl1 driver.
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Inverting the crc after calling ether_crc_le() is unnecessary and breaks
multicast. Remove it.
Tested-by: David Madore <david.madore@ens.fr>
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We weren't unmapping DMA memory, which will break when gianfar gets used
on systems with more than 32-bits of memory. Also, it's just plain wrong.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
p_{tx,rx}_fw_statistics_pram are special: they're available only when
a device is open. If the device is closed, we should just fill the data
with zeroes.
Fixes the following oops:
root@b1:~# ifconfig eth1 down
root@b1:~# ethtool -S eth1
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc01e1dcc
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c01e1dcc] uec_get_ethtool_stats+0x98/0x124
LR [c0287cc8] ethtool_get_stats+0xfc/0x23c
Call Trace:
[cfaadde0] [c0287ca8] ethtool_get_stats+0xdc/0x23c (unreliable)
[cfaade20] [c0288340] dev_ethtool+0x2fc/0x588
[cfaade50] [c0285648] dev_ioctl+0x290/0x33c
[cfaadea0] [c0272238] sock_ioctl+0x80/0x2ec
[cfaadec0] [c00b5ae4] vfs_ioctl+0x40/0xc0
[cfaadee0] [c00b5fa8] do_vfs_ioctl+0x78/0x20c
[cfaadf10] [c00b617c] sys_ioctl+0x40/0x74
[cfaadf40] [c00142d8] ret_from_syscall+0x0/0x38
[...]
---[ end trace b941007b2dfb9759 ]---
Segmentation fault
p.s. While at it, also remove u64 casts, they aren't needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This driver is pretty mature, and the worst of the known
problems has been fixed (the 32-bit failures due to readq
implementation).
So let's finally give it a version of 1.0
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Sun CP3260 ATCA blade which is
a N2 based ATCA blade with 2 NIU ports. The NIU ports do not
have on-board PHY.
Signed-off-by: Santwona Behera <santwona.behera@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch it is possible to select drivers which require
bestcomm support without bestcomm support being selected. This
patch reworks the bestcomm dependencies to ensure the correct
bestcomm tasks are always enabled.
Reported-by: Hans Lehmann <hans.lehmann@ritter-elektronik.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add support to drivers/net/usb/asix.c for the Cables-to-Go "USB 2.0 to
10/100 Ethernet Adapter". USB id 0b95:772a.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bnx2: fix poll_controller to pass proper structures and check all rx queues
niu: Fix readq implementation when architecture does not provide one.
hostap: pad the skb->cb usage in lieu of a proper fix
rtl8187 : support for Sitecom WL-168 0001 v4
mac80211: fix notify_mac function
rtl8187: Add Abocom USB ID
net: put_cmsg_compat + SO_TIMESTAMP[NS]: use same name for value as caller
tcp_htcp: last_cong bug fix
[netdrvr] smc911x: fix for driver resume (and compilation warning)
RDMA/cxgb3: deadlock in iw_cxgb3 can cause hang when configuring interface.
cxgb3 - Limit multiqueue setting to msi-x
cxgb3 - eeprom read fixes
myri10ge: fix stop/go ordering even more
Fix bnx2 so that netpoll works properly. Specifically:
1) Fix parameters to bnx2_interrupt to be a struct bnx2_napi rather than a
struct net_device
2) Fix poll_controller method to check every queue in the rx case so frames
aren't missed
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a TX hang reported by Jesper Dangaard Brouer.
When an architecutre cannot provide a fully functional
64-bit atomic readq/writeq, the driver must implement
it's own. This is because only the driver can say whether
doing something like using two 32-bit reads to implement
the full 64-bit read will actually work properly.
In particular one of the issues is whether the top 32-bits
or the bottom 32-bits of the 64-bit register should be read
first. There could be side effects, and in fact that is
exactly the problem here.
The TX_CS register has counters in the upper 32-bits and
state bits in the lower 32-bits. A read clears the state
bits.
We would read the counter half before the state bit half.
That first read would clear the state bits, and then the
driver thinks that no interrupts are pending because the
interrupt indication state bits are seen clear every time.
Fix this by reading the bottom half before the upper half.
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like mac80211 did, this driver makes 'clever' use of skb->cb to pass
information along with an skb as it is requeued from the virtual device
to the physical wireless device. Unfortunately, that trick no longer
works...
Unlike mac80211, code complexity and driver apathy makes this hack
the best option we have in the short run. Hopefully someone will
eventually be motivated to code a proper fix before all the effected
hardware dies.
(Above text by me. Johannes officially disavows all knowledge of this
hack. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the Sitecom 0001 v4 with product id 0x0df6:0028, uses Realtek's
RTL8187B and work fine with new 2.6.27 driver.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix crash in path_rec_completion()
IPoIB: Fix hang in ipoib_flush_paths()
IPoIB: Don't enable NAPI when it's already enabled
RDMA/cxgb3: Fix deadlock in iw_cxgb3 (hang when configuring interface)
IB/ehca: Remove reference to special QP in case of port activation failure
IB/mlx4: Set umem field to NULL in mlx4_ib_alloc_fast_reg_mr()
mlx4_core: Fix unused variable warning
RDMA/nes: Mitigate compatibility issue regarding PCIe write credits
RDMA/nes: Fix CQ allocation scheme for multicast receive queue apps
RDMA/nes: Correct handling of PBL resources
RDMA/nes: Reindent mis-indented spinlocks
RDMA/cxgb3: Fix too-big reserved field zeroing in iwch_post_zb_read()
IB/ipath: Fix RDMA write with immediate copy of last packet
When the iw_cxgb3 module's cxgb3_client "add" func gets called by the
cxgb3 module, the iwarp driver ends up calling the ethtool ops
get_drvinfo function in cxgb3 to get the fw version and other info.
Currently the iwarp driver grabs the rtnl lock around this down call
to serialize. As of 2.6.27 or so, things changed such that the rtnl
lock is held around the call to the netdev driver open function. Also
the cxgb3_client "add" function doesn't get called if the device is
down.
So, if you load cxgb3, then load iw_cxgb3, then ifconfig up the
device, the iw_cxgb3 add func gets called with the rtnl_lock held. If
you load cxgb3, ifconfig up the device, then load iw_cxgb3, the add
func gets called without the rtnl_lock held. The former causes the
deadlock, the latter does not.
In addition, there are iw_cxgb3 sysfs handlers that also can call down
into cxgb3 to gather the fw and hw versions. These can be called
concurrently on different processors and at any time. Thus we need to
push this serialization down in the cxgb3 driver get_drvinfo func.
The fix is to remove rtnl lock usage, and use a per-device lock in cxgb3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I am trying out suspend, resume on an OMAP3 based board. What I see
during resume is that the SMC911x driver resume routing gets stuck
after trying to transmit the packet out of the controller. Some debug
messages below:
--> smc911x_drv_resume
eth0: --> smc911x_reset
eth0: smc911x_reset timeout waiting for PM restore
eth0: --> smc911x_enable
eth0: --> smc911x_phy_configure()
eth0: --> smc911x_phy_reset()
eth0: phy caps=0x782d
eth0: phy advertised caps=0x0de1
eth0: --> smc911x_phy_check_media
smc911x_phy_read: phyaddr=0x1, phyreg=0x01, phydata=0x7809
smc911x_phy_read: phyaddr=0x1, phyreg=0x01, phydata=0x7809
eth0: link down
Restarting tasks ... eth0: --> smc911x_hard_start_xmit
eth0: --> smc911x_hardware_send_pkt
eth0: --> smc911x_hard_start_xmit
eth0: --> smc911x_hardware_send_pkt
eth0: --> smc911x_hard_start_xmit
eth0: --> smc911x_hardware_send_pkt
nfs: server 172.24.190.217 not responding, still trying
nfs: server 172.24.190.217 not responding, still trying
The following change makes it work fine: (The change within
smc911x_drv_probe function was to get rid of a compilation warning).
Signed-off-by: Romit Dasgupta <romit@ti.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When the iw_cxgb3 module's cxgb3_client "add" func gets called by the
cxgb3 module, the iwarp driver ends up calling the ethtool ops get_drvinfo
function in cxgb3 to get the fw version and other info. Currently the
iwarp driver grabs the rtnl lock around this down call to serialize.
As of 2.6.27 or so, things changed such that the rtnl lock is held around
the call to the netdev driver open function. Also the cxgb3_client "add"
function doesn't get called if the device is down.
So, if you load cxgb3, then load iw_cxgb3, then ifconfig up the device,
the iw_cxgb3 add func gets called with the rtnl_lock held. If you
load cxgb3, ifconfig up the device, then load iw_cxgb3, the add func
gets called without the rtnl_lock held. The former causes the deadlock,
the latter does not.
In addition, there are iw_cxgb3 sysfs handlers that also can call
down into cxgb3 to gather the fw and hw versions. These can be called
concurrently on different processors and at any time. Thus we need to
push this serialization down in the cxgb3 driver get_drvinfo func.
The fix is to remove rtnl lock usage, and use a per-device lock in cxgb3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Protect against invalid phy entries in the eeprom.
Extend eeprom access timeout.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The doorbell writes may be seen out of order by the firmware if they
are in WC memory since the tx spin(un)lock does not flush WC writes.
Hence if the "stop" is written on a different CPU than the "go", it
is possible that the stop will arrive after the go unless we add an
explicit memory barrier (and mmiowb() is not enough).
It fixes transmit hangs in multi tx queue mode.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Yup, this appears to be the problem, thanks. I think &hso_net->net->dev
is more intuitive for the error message, so I've used that. I've also
added missing line endings on the error messages and set our local
rfkill structure element to NULL on failure so we don't try to call
rfkill_unregister on driver removal if we failed to register at all.
The patch below Works For Me (TM); the device is detected fine, can be
removed without problems and connects ok. I'll have a prod at why the
rfkill stuff isn't working next, but I believe this cleanup of the error
handling is appropriate no matter what the issue with registration is.
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Due to a hardware bug, the originally assigned range cannot reliably
be used for boot configuration and must not be modifiable through
ethtool.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tried to deactivate rx ring that wasn't activated,
used wrong index.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Fix recursive descent in __scm_destroy().
iwl3945: fix deadlock on suspend
iwl3945: do not send scan command if channel count zero
iwl3945: clear scanning bits upon failure
ath5k: correct handling of rx status fields
zd1211rw: Add 2 device IDs
Fix logic error in rfkill_check_duplicity
iwlagn: avoid sleep in softirq context
iwlwifi: clear scanning bits upon failure
Revert "ath5k: honor FIF_BCN_PRBRESP_PROMISC in STA mode"
tcp: Fix recvmsg MSG_PEEK influence of blocking behavior.
netfilter: netns ct: walk netns list under RTNL
ipv6: fix run pending DAD when interface becomes ready
net/9p: fix printk format warnings
net: fix packet socket delivery in rx irq handler
xfrm: Have af-specific init_tempsel() initialize family field of temporary selector
This patch fixes iwl3945 deadlock during suspend by moving notify_mac out
of iwl3945 mutex. This is a portion of the same fix for iwlwifi by Tomas.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ensures we clear any scan status bit when
an error occurs while sending the scan command. It is
the implementation of patch:
"iwlwifi: clear scanning bits upon failure"
for iwl3945.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_rx_status fields rs_antenna and rs_more are u8s, but we
were setting them with bitwise ANDs of 32-bit values.
As a consequence, jumbo frames would not be discarded as intended.
Then, because the hw rate value of such frames is zero, and, since
"ath5k: rates cleanup", we do not fall back to the basic rate, such
packets would trigger the following WARN_ON:
------------[ cut here ]------------
WARNING: at net/mac80211/rx.c:2192 __ieee80211_rx+0x4d/0x57e [mac80211]()
Modules linked in: ath5k af_packet sha256_generic aes_i586 aes_generic cbc loop i915 drm binfmt_misc acpi_cpufreq fan container nls_utf8 hfsplus dm_crypt dm_mod kvm_intel kvm fuse sbp2 snd_hda_intel snd_pcm_oss snd_pcm snd_mixer_oss snd_seq_dummy snd_seq_oss arc4 joydev hid_apple ecb snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device usbhid appletouch mac80211 sky2 snd ehci_hcd ohci1394 bitrev crc32 sr_mod cdrom rtc sg uhci_hcd snd_page_alloc cfg80211 ieee1394 thermal ac battery processor button evdev unix [last unloaded: ath5k]
Pid: 0, comm: swapper Tainted: G W 2.6.28-rc2-wl #14
Call Trace:
[<c0123d1e>] warn_on_slowpath+0x41/0x5b
[<c012005d>] ? sched_debug_show+0x31e/0x9c6
[<c012489f>] ? vprintk+0x369/0x389
[<c0309539>] ? _spin_unlock_irqrestore+0x54/0x58
[<c011cd8f>] ? try_to_wake_up+0x14f/0x15a
[<f81918cb>] __ieee80211_rx+0x4d/0x57e [mac80211]
[<f828872a>] ath5k_tasklet_rx+0x5a1/0x5e4 [ath5k]
[<c013b9cd>] ? clockevents_program_event+0xd4/0xe3
[<c01283a9>] tasklet_action+0x94/0xfd
[<c0127d19>] __do_softirq+0x8c/0x13e
[<c0127e04>] do_softirq+0x39/0x55
[<c0128082>] irq_exit+0x46/0x85
[<c010576c>] do_IRQ+0x9a/0xb2
[<c010461c>] common_interrupt+0x28/0x30
[<f80e934a>] ? acpi_idle_enter_bm+0x2ad/0x31b [processor]
[<c02976bf>] cpuidle_idle_call+0x65/0x9a
[<c010262c>] cpu_idle+0x76/0xa6
[<c02fb402>] rest_init+0x62/0x64
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
07fa/1196
Bewan BWIFI-USB54AR: Tested by night1308, this device is a ZD1211B with
an AL2230S radio.
0ace/b215
HP 802.11abg: Tested by Robert Philippe
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__ieee80211_tasklet_handler -> __ieee80211_rx ->
__ieee80211_rx_handle_packet -> ieee80211_invoke_rx_handlers ->
ieee80211_rx_h_decrypt -> ieee80211_crypto_tkip_decrypt ->
ieee80211_tkip_decrypt_data -> iwl4965_mac_update_tkip_key ->
iwl_scan_cancel_timeout -> msleep
Ooops!
Avoid the sleep by changing iwl_scan_cancel_timeout with
iwl_scan_cancel and simply returning on failure if the scan persists.
This will cause hardware decryption to fail and we'll handle a few more
frames with software decryption.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwl_bg_request_scan function, if we could not send a
scan command it will go to done.
In done it does the right thing to call mac80211 with
scan complete, but the problem is STATUS_SCAN_HW is still
set causing any future scan to fail. Fix by clearing the scanning status
bits if scan fails.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unfortunately, the result was that mac80211 didn't see all the beacons
it actually wanted to see. This caused lost associations.
Hopefully we can revisit this when mac80211 is less greedy about seeing
beacons directly...
This reverts commit 063279062a.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix
drivers/net/mlx4/profile.c:55: warning: 'res_name' defined but not used
by making mlx4_dbg() always use all of its parameters, regardless of
whether CONFIG_MLX4_DEBUG is set or not.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
xfrm: Fix xfrm_policy_gc_lock handling.
niu: Use pci_ioremap_bar().
bnx2x: Version Update
bnx2x: Calling netif_carrier_off at the end of the probe
bnx2x: PCI configuration bug on big-endian
bnx2x: Removing the PMF indication when unloading
mv643xx_eth: fix SMI bus access timeouts
net: kconfig cleanup
fs_enet: fix polling
XFRM: copy_to_user_kmaddress() reports local address twice
SMC91x: Fix compilation on some platforms.
udp: Fix the SNMP counter of UDP_MIB_INERRORS
udp: Fix the SNMP counter of UDP_MIB_INDATAGRAMS
drivers/net/smc911x.c: Fix lockdep warning on xmit.
netif_carrier_off was called too early at the probe. In case of failure
or simply bad timing, this can cause a fatal error since linkwatch_event
might run too soon.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code read nothing but zeros on big-endian (wrong part of the
32bits). This caused poor performance on big-endian machines. Though this
issue did not cause the system to crash, the performance is significantly
better with the fix so I view it as critical bug fix.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PMF flag is set, the driver can access the HW freely. When the
driver is unloaded, it should not access the HW. The problem caused fatal
errors when "ethtool -i" was called after the calling instance was unloaded
and another instance was already loaded
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv643xx_eth mii bus implementation uses wait_event_timeout() to
wait for SMI completion interrupts.
If wait_event_timeout() would return zero, mv643xx_eth would conclude
that the SMI access timed out, but this is not necessarily true --
wait_event_timeout() can also return zero in the case where the SMI
completion interrupt did happen in time but where it took longer than
the requested timeout for the process performing the SMI access to be
scheduled again. This would lead to occasional SMI access timeouts
when the system would be under heavy load.
The fix is to ignore the return value of wait_event_timeout(), and
to re-check the SMI done bit after wait_event_timeout() returns to
determine whether or not the SMI access timed out.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The bool kconfig option added to ixgbe and myri10ge for DCA is ambigous,
so this patch adds a description to the kconfig option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This reverts 51ac3beffd ('SMC91x: delete
unused local variable "lp"') and adds __maybe_unused markers to these
(potentially) unused variables.
The issue is that in some configurations SMC_IO_SHIFT evaluates
to '(lp->io_shift)', but in some others it's plain '0'.
Based upon a build failure report from Manuel Lauss.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
af_unix: netns: fix problem of return value
IRDA: remove double inclusion of module.h
udp: multicast packets need to check namespace
net: add documentation for skb recycling
key: fix setkey(8) policy set breakage
bpa10x: free sk_buff with kfree_skb
xfrm: do not leak ESRCH to user space
net: Really remove all of LOOPBACK_TSO code.
netfilter: nf_conntrack_proto_gre: switch to register_pernet_gen_subsys()
netns: add register_pernet_gen_subsys/unregister_pernet_gen_subsys
net: delete excess kernel-doc notation
pppoe: Fix socket leak.
gianfar: Don't reset TBI<->SerDes link if it's already up
gianfar: Fix race in TBI/SerDes configuration
at91_ether: request/free GPIO for PHY interrupt
amd8111e: fix dma_free_coherent context
atl1: fix vlan tag regression
SMC91x: delete unused local variable "lp"
myri10ge: fix stop/go mmio ordering
bonding: fix panic when taking bond interface down before removing module
...
dev_kfree_skb should not be called with irqs disabled, use dev_kfree_skb_irq
instead. The warning caused looks like this:
======================================================
[ INFO: hard-safe -> hard-unsafe lock order detected ]
2.6.28-rc1 #273
------------------------------------------------------
swapper/0 [HC0[0]:SC1[2]:HE0:SE0] is trying to acquire:
(clock-AF_INET){-..+}, at: [<4015c17c>] _sock_def_write_space+0x28/0xd8
and this task is already holding:
(&lp->lock){++..}, at: [<4013f230>] _smc911x_hard_start_xmit+0x30/0x4b8
which would create a new lock dependency:
(&lp->lock){++..} -> (clock-AF_INET){-..+}
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As noticed by Saikiran Madugula, commit 7447ef63cf
("loopback: Remove rest of LOOPBACK_TSO code.") got rid of
emulate_large_send_offload() but didn't get rid of the call
site as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove excess kernel-doc function parameters from networking header
& driver files:
Warning(include/net/sock.h:946): Excess function parameter or struct member 'sk' description in 'sk_filter_release'
Warning(include/linux/netdevice.h:1545): Excess function parameter or struct member 'cpu' description in 'netif_tx_lock'
Warning(drivers/net/wan/z85230.c:712): Excess function parameter or struct member 'regs' description in 'z8530_interrupt'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move SKB trim before we lookup the socket so we don't have to
put it on failure.
Based upon an initial patch by Jarek Poplawski and suggestions
from Herbert Xu.
Signed-off-by: David S. Miller <davem@davemloft.net>
The link may be up already via the chip's reset strapping, or though action
of U-Boot, or from the last time the interface was brought up. Resetting
the link causes it to go down for several seconds. This can significantly
increase the time from power-on to DHCP completion and a device being
accessible to the network.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The init_phy() function attaches to the PHY, then configures the
SerDes<->TBI link (in SGMII mode). The TBI is on the MDIO bus with the PHY
(sort of) and is accessed via the gianfar's MDIO registers, using the
functions gfar_local_mdio_read/write(), which don't do any locking.
The previously attached PHY will start a work-queue on a timer, and
probably an irq handler as well, which will talk to the PHY and thus use
the MDIO bus. This uses phy_read/write(), which have locking, but not
against the gfar_local_mdio versions.
The result is that PHY code will try to use the MDIO bus at the same time
as the SerDes setup code, corrupting the transfers.
Setting up the SerDes before attaching to the PHY will insure that there is
no race between the SerDes code and *our* PHY, but doesn't fix everything.
Typically the PHYs for all gianfar devices are on the same MDIO bus, which
is associated with the first gianfar device. This means that the first
gianfar's SerDes code could corrupt the MDIO transfers for a different
gianfar's PHY.
The lock used by phy_read/write() is contained in the mii_bus structure,
which is pointed to by the PHY. This is difficult to access from the
gianfar drivers, as there is no link between a gianfar device and the
mii_bus which shares the same MDIO registers. As far as the device layer
and drivers are concerned they are two unrelated devices (which happen to
share registers).
Generally all gianfar devices' PHYs will be on the bus associated with the
first gianfar. But this might not be the case, so simply locking the
gianfar's PHY's mii bus might not lock the mii bus that the SerDes setup
code is going to use.
We solve this by having the code that creates the gianfar platform device
look in the device tree for an mdio device that shares the gianfar's
registers. If one is found the ID of its platform device is saved in the
gianfar's platform data.
A new function in the gianfar mii code, gfar_get_miibus(), can use the bus
ID to search through the platform devices for a gianfar_mdio device with
the right ID. The platform device's driver data is the mii_bus structure,
which the SerDes setup code can use to lock the current bus.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When the at91_ether driver is using a GPIO for its PHY interrupt,
be sure to request (and later, if needed, free) that GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 401c0aabec introduced a regression
in the atl1 driver by storing the VLAN tag in the wrong TX descriptor
field.
This patch causes the VLAN tag to be stored in its proper location.
Tested-by: Ramon Casellas <ramon.casellas@cttc.es>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use mmiowb() to ensure "stop" and "go" commands are sent in order on ia64.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A panic was discovered with bonding when using mode 5 or 6 and trying to
remove the slaves from the bond after the interface was taken down.
When calling 'ifconfig bond0 down' the following happens:
bond_close()
bond_alb_deinitialize()
tlb_deinitialize()
kfree(bond_info->tx_hashtbl)
bond_info->tx_hashtbl = NULL
Unfortunately if there are still slaves in the bond, when removing the
module the following happens:
bonding_exit()
bond_free_all()
bond_release_all()
bond_alb_deinit_slave()
tlb_clear_slave()
tx_hash_table = BOND_ALB_INFO(bond).tx_hashtbl
u32 next_index = tx_hash_table[index].next
As you might guess we panic when trying to access a few entries into the
table that no longer exists.
I experimented with several options (like moving the calls to
tlb_deinitialize somewhere else), but it really makes the most sense to
be part of the bond_close routine. It also didn't seem logical move
tlb_clear_slave around too much, so the simplest option seems to add a
check in tlb_clear_slave to make sure we haven't already wiped the
tx_hashtbl away before searching for all the non-existent hash-table
entries that used to point to the slave as the output interface.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch reworks the resource free logic performed at the time
a bonding device is released. This (a) closes two resource leaks, one
for workqueues and one for multicast lists, and (b) improves commonality
of code between the "destroy one" and "destroy all" paths by performing
final free activity via destructor instead of explicitly (and differently)
in each path.
"Sean E. Millichamp" <sean@bruenor.org> reported the workqueue
leak, and included a different patch.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
During the rework of the mii monitor for:
commit f0c76d6177
Author: Jay Vosburgh <fubar@us.ibm.com>
Date: Wed Jul 2 18:21:58 2008 -0700
bonding: refactor mii monitor
I left out the increment of the link failure counter. This
patch corrects that omission.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We were setting RX_FILTER_BEACON even after entering STA mode,
which leads to a lot of unnecessary wakeups. This should fix the
bug "Ath5k driver has too many interrupts per second at idle" at
http://bugzilla.kernel.org/show_bug.cgi?id=11749.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take care to handle register 0xa228 exactly as in the HAL released by
Atheros. This change is required to make ath5k work again on my system
since commit 2203d6be (ath5k: Misc hw_reset updates), thus fixing a
regression in 2.6.27 and therefore hopefully eligible for inclusion into
a stable release.
v2: Only overwrite initial register values on later revisions of AR5212
chips.
v3: Use standard macros to manipulate the register.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make menuconfig RT2X00 a tristate instead of boolean,
otherwise we do not correctly inherit the mac80211 value
on which RT2X00 depends, and makes it possible to
compile rt2x00 into the kernel while mac80211 is a
module.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If somebody sends an invalid beacon/probe response, that can trash the
whole BSS descriptor. The descriptor is, luckily, large enough so that
it cannot scribble past the end of it; it's well above 400 bytes long.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.24-2.6.27, bug present in some form since driver was added (2.6.22)]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg detected this two sparse warnings:
drivers/net/wireless/libertas/cmd.c:609:16: warning: cast to restricted __le16
drivers/net/wireless/libertas/cmd.c:611:16: warning: cast to restricted __le16
... but cmd.minlevel is "s8", so we can access it directly and hope
for the sign-extension-code in the compiler to convert that to the
"s16" type.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes suspend to RAM after by moving
notify_mac out of iwlwifi mutex
http://bugzilla.kernel.org/show_bug.cgi?id=11845
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Carlos R. Mafra <crmafra2@gmail.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The amd8111e rx poll routine currently mishandles the case when we
process exactly the number of packets specified in the budget.
This patch is basically as suggested by David Miller.
Signed-off-by: Chris Friesen <cfriesen@nortel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
