The eeh_ops->probe() function is called from two different contexts:
1. On pseries, where we set EEH_PROBE_MODE_DEVTREE, it's called in
eeh_add_device_early() which is supposed to run before we create
a pci_dev.
2. On PowerNV, where we set EEH_PROBE_MODE_DEV, it's called in
eeh_device_add_late() which is supposed to run *after* the
pci_dev is created.
The "early" probe is required because PAPR requires that we perform an RTAS
call to enable EEH support on a device before we start interacting with it
via config space or MMIO. This requirement doesn't exist on PowerNV and
shoehorning two completely separate initialisation paths into a common
interface just results in a convoluted code everywhere.
Additionally the early probe requires the probe function to take an pci_dn
rather than a pci_dev argument. We'd like to make pci_dn a pseries specific
data structure since there's no real requirement for them on PowerNV. To
help both goals move the early probe into the pseries containment zone
so the platform depedence is more explicit.
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-5-oohall@gmail.com
The pci hotplug helper (pci_hp_add_devices()) calls
eeh_add_device_tree_early() to scan the device-tree for new PCI devices and
do the early EEH probe before the device is scanned. This early probe is a
no-op in a lot of cases because:
a) The early init is only required to satisfy a PAPR requirement that EEH
be configured before we start doing config accesses. On PowerNV it is
a no-op.
b) It's a no-op for devices that have already had their eeh_dev
initialised.
There are four callers of pci_hp_add_devices():
1. arch/powerpc/kernel/eeh_driver.c
Here the hotplug helper is called when re-scanning pci_devs that
were removed during an EEH recovery pass. The EEH stat for each
removed device (the eeh_dev) is retained across a recovery pass
so the early init is a no-op in this case.
2. drivers/pci/hotplug/pnv_php.c
This is also a no-op since the PowerNV hotplug driver is, suprisingly,
PowerNV specific.
3. drivers/pci/hotplug/rpaphp_core.c
4. drivers/pci/hotplug/rpaphp_pci.c
In these two cases new devices have been hotplugged and FW has
provided new DT nodes for each. These are the only two cases where
the EEH we might have new PCI device nodes in the DT so these are
the only two cases where the early EEH probe needs to be done.
We can move the calls to eeh_add_device_tree_early() to the locations where
it's needed and remove it from the generic path. This is preparation for
making the early EEH probe pseries specific.
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-3-oohall@gmail.com
Ever since the PCI hotplug core was introduced in 2002, drivers had to
allocate and register a struct hotplug_slot_info for every slot:
https://git.kernel.org/tglx/history/c/a8a2069f432c
Apparently the idea was that drivers furnish the hotplug core with an
up-to-date card presence status, power status, latch status and
attention indicator status as well as notify the hotplug core of changes
thereof. However only 4 out of 12 hotplug drivers bother to notify the
hotplug core with pci_hp_change_slot_info() and the hotplug core never
made any use of the information: There is just a single macro in
pci_hotplug_core.c, GET_STATUS(), which uses the hotplug_slot_info if
the driver lacks the corresponding callback in hotplug_slot_ops. The
macro is called when the user reads the attribute via sysfs.
Now, if the callback isn't defined, the attribute isn't exposed in sysfs
in the first place (see e.g. has_power_file()). There are only two
situations when the hotplug_slot_info would actually be accessed:
* If the driver defines ->enable_slot or ->disable_slot but not
->get_power_status.
* If the driver defines ->set_attention_status but not
->get_attention_status.
There is no driver doing the former and just a single driver doing the
latter, namely pnv_php.c. Amend it with a ->get_attention_status
callback. With that, the hotplug_slot_info becomes completely unused by
the PCI hotplug core. But a few drivers use it internally as a cache:
cpcihp uses it to cache the latch_status and adapter_status.
cpqhp uses it to cache the adapter_status.
pnv_php and rpaphp use it to cache the attention_status.
shpchp uses it to cache all four values.
Amend these drivers to cache the information in their private slot
struct. shpchp's slot struct already contains members to cache the
power_status and adapter_status, so additional members are only needed
for the other two values. In the case of cpqphp, the cached value is
only accessed in a single place, so instead of caching it, read the
current value from the hardware.
Caution: acpiphp, cpci, cpqhp, shpchp, asus-wmi and eeepc-laptop
populate the hotplug_slot_info with initial values on probe. That code
is herewith removed. There is a theoretical chance that the code has
side effects without which the driver fails to function, e.g. if the
ACPI method to read the adapter status needs to be executed at least
once on probe. That seems unlikely to me, still maintainers should
review the changes carefully for this possibility.
Rafael adds: "I'm not aware of any case in which it will break anything,
[...] but if that happens, it may be necessary to add the execution of
the control methods in question directly to the initialization part."
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> # drivers/pci/hotplug/rpa*
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # drivers/pci/hotplug/s390*
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # drivers/platform/x86
Cc: Len Brown <lenb@kernel.org>
Cc: Scott Murray <scott@spiteful.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Oliver OHalloran <oliveroh@au1.ibm.com>
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
Add SPDX GPL-2.0+ to all PCI files that specified the GPL and allowed
either GPL version 2 or any later version.
Remove the boilerplate GPL version 2 or later language, relying on the
assertion in b24413180f ("License cleanup: add SPDX GPL-2.0 license
identifier to files with no license") that the SPDX identifier may be used
instead of the full boilerplate text.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have a custom printf format specifier, convert users of
full_name() to use %pOF instead. This is preparation for removing storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
This renames pcibios_find_pci_bus() to pci_find_bus_by_node() to
avoid conflicts with those PCI subsystem weak function names, which
have prefix "pcibios". No logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This renames pcibios_{add,remove}_pci_devices() to avoid conflicts
with names of the weak functions in PCI subsystem, which have the
prefix "pcibios". No logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-By: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix all whitespace issues (missing or needed whitespace) in all files in
drivers/pci. Code is compiled with allyesconfig before and after code
changes and objects are recorded and checked with objdiff and they are not
changed after this commit.
Signed-off-by: Bogicevic Sasa <brutallesale@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix whitespace, capitalization, and spelling errors. No functional change.
I know "busses" is not an error, but "buses" was more common, so I used it
consistently.
Signed-off-by: Marta Rybczynska <rybczynska@gmail.com> (pci_reset_bridge_secondary_bus())
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Change debug variable name to one more unique to this driver.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix presentation of the slot number in the /sys/bus/pci/slots
directory to match that used in the majority of other drivers.
> Greg said:
> How is anyone supposed to write sane managability tools in the
> presence
> of such anarchy?
>
> > ~ # cat /sys/bus/pci/slots/0000:00:02.2/phy_location
> > U787A.001.DNZ00Z5-P1-C2
>
> Right. This should look like:
>
> # cat /sys/bus/pci/slots/U787A.001.DNZ00Z5-P1-C2/address
> 0000:00:02
This patch implements exactly what you describe. Boot tested.
I assume you really mean it -- if so, then please review and
ack the patch !?
I have absolutely no clue if this breaks any existing IBM tools.
I'm pretty sure it doesn't ... but attention Mike Strosaker! does it?
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: <strosake@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rename rpaphp_register_pci_slot() because its easy to confuse
with rpaphp_register_slot() even though it does something
completely different. Rename it to rpaphp_enable_slot() because
its almost identical to enbale_slot().
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Eliminate the tail call to rpaphp_register_slot()
by placing it in the caller. This will help later
dis-entanglement.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The debug function print_slot_pci_funcs() is a large wrapper
around two debug print statements. Just invoke these directly.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The setup_pci_slot() routine appears to be nothing else than
a big, complicated wrapper around pcibios_add_pci_devices().
Remove the wrapping, and call pcibios_add_pci_devices() directly.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove another stove-pipe; this funcion was called from
two different places, with a compile-time const that is
then run-time checked to perform two different things.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove another stovepipe: a call which wraps another call, and
just adds printks.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove a stove-pipe-- a function that is called from only one place,
does nothing but wraps another function with debug printk's.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The routine that called an alloc should be the same routine that
calles the mathcing free, if anything in the middle failed.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanup. Add the prefix rpaphp_* to several generic-sounding routines.
Remove rpaphp_remove_slot(), which is a one-liner.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove general baroqueness. The function rpaphp_enable_pci_slot()
has a fairly simple logic structure, once all of the debug printk's
are removed. Its called from only one place, and that place also
has a very simple structure once he printk's are removed. Merge
the two together.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove general baroqueness. The function rpaphp_unconfig_pci_adapter()
is really just three lines of code, once all the dbg printks are removed.
And its called in only one place. So replace the call by the thre lines.
Also, provide proper semaphore locking in the affected function
disable_slot()
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function rpaphp_eeh_remove_bus_device() is a dupe of
eeh_remove_bus_device(). Remove it.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove general baroqueness. The function rpaphp_config_pci_adapter()
is really just one line of code, once all the dbg printks are removed.
And its called in only one place. So replace the call by the one line.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function rpaphp_fixup_new_pci_devices() has been migrated to
pcibios_fixup_new_pci_devices() in
arch/powerpc/platforms/pseries/pci_dlpar.c
This patch removes the old version.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function rpaphp_find_pci_bus() has been migrated to
pcibios_find_pci_bus() in arch/powerpc/platforms/pseries/pci_dlpar.c
This patch removes the old version.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a small patch to reduce the nr. of pointer dereferences in
drivers/pci/hotplug/rpaphp_pci.c
Benefits:
- micro speed optimization due to fewer pointer derefs
- generated code should be slightly smaller
- better readability
note: due to lack of both hardware and cross-compile tools this patch is,
unfortunately, completely untested.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The RPAPHP code contains two routines that appear to be gratuitous copies
of very similar pci code. In particular,
rpaphp_claim_resource ~~ pci_claim_resource
(there is a minor, non-functional difference)
rpadlpar_claim_one_bus == pcibios_claim_one_bus
(the code is identical)
This patch removes the rpaphp versions of the code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The RPAPHP code contains a routine that duplicates some existing code.
This patch removes the rpaphp version of the code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(akpm: _machine is some ppc64 thing - this is a powerpc-only driver)
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the driver bits for enabling DLPAR and PCI Hotplug
for the new OF-based PCI probe. This functionality was regressed when
the new PCI approach was introduced. Please apply if appropriate.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a minor patch to the ppc64 PCI hotplug code; it makes the call to
rpaphp_unconfig_pci_adapter() symmetric with respect to the call to
rpaphp_config_pci_adapter(). I discussed this with John Rose, who
had provided the last round of changes for these functions; he
appearently had this patch but somehow failed to mail it out.
Tested. (added/removed device).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
drivers/pci/hotplug/rpaphp.h | 3 ++-
drivers/pci/hotplug/rpaphp_core.c | 5 ++++-
drivers/pci/hotplug/rpaphp_pci.c | 11 +++--------
3 files changed, 9 insertions(+), 10 deletions(-)
This patch pulls the PCI-related junk out of struct device_node and
puts it in a separate structure, struct pci_dn. The device_node now
just has a void * pointer in it, which points to a struct pci_dn for
nodes that represent PCI devices. It could potentially be used in
future for device-specific data for other sorts of devices, such as
virtual I/O devices.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently rpaphp registers the following bus types as hotplug slots:
1) Actual PCI Hotplug slots
2) Embedded/Internal PCI slots
3) PCI Host Bridges
The second and third bus types are not actually direct parents of
removable adapters. As such, the rpaphp has special case code to fake
results for attributes like power, adapter status, etc. This patch
removes types 2 and 3 from the rpaphp module.
This patch also changes the DLPAR module so that slots can be
DLPAR-added/removed without having been designated as hotplug-capable.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch exports rpaphp_config_pci_adapter() for use by the rpadlpar
module. It also changes this function by removing any dependencies on
struct slot. The patch also changes the RPA DLPAR-add path to enable
newly-added slots in a separate step from that which registers them as
hotplug slots.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The rpaphp module currently uses a fragile method to find a pci device
by its device node. This function is unnecessary, so this patch scraps
it.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The slot structure in the rpaphp module currently references the PCI
contents of the slot using the PCI device of the parent bridge. This
is unnecessary, since the module is actually interested in the
subordinate bus of the bridge. The dependency on a PCI bridge device
also prohibits the module from registering hotplug slots that have a
root bridge as a parent, since root bridges on PPC64 don't have PCI
devices.
This patch changes struct slot to reference the PCI subsystem using a
pci_bus rather than a pci_dev.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, rpaphp registers Virtual I/O slots as hotplug slots. The
only purpose of this registration is to ensure that the VIO subsystem
is notified of new VIO buses during DLPAR adds. Similarly, rpaphp
notifies the VIO subsystem when a VIO bus is DLPAR-removed. The rpaphp
module has special case code to fake results for attributes like power,
adapter status, etc.
The VIO register/unregister functions could just as easily be made from
the DLPAR module. This patch moves the VIO registration calls to the
DLPAR module, and removes the VIO fluff from rpaphp altogether.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
