The libsas error handler has two fairly fatal bugs
1. scsi_sas_task_done calls scsi_eh_finish_cmd() too early. This
happens if the task completes after it has been aborted but before
the error handler starts up. Because scsi_eh_finish_cmd()
decrements host_failed and adds the task to the done list, the
error handler start check (host_failed == host_busy) never passes
and the eh never starts.
2. The multiple task completion paths sas_scsi_clear_queue_... all
simply delete the task from the error queue. This causes it to
disappear into the ether, since a command must be placed on the
done queue to be finished off by the error handler. This behaviour
causes the HBA to hang on pending commands.
Fix 1. by moving the SAS_TASK_STATE_ABORTED check to an exit clause at
the top of the routine and calling ->scsi_done() unconditionally (it
is a nop if the timer has fired). This keeps the task in the error
handling queue until the eh starts.
Fix 2. by making sure every task goes through task complete followed
by scsi_eh_finish_cmd().
Tested this by firing resets across a disk running a hammer test (now
it actually survives without hanging the system)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
arcmsr_iop_message_xfer() is called from atomic context under the
queuecommand scsi_host_template handler. James Bottomley pointed out
that the current GFP_KERNEL|GFP_DMA flags are wrong: firstly we are in
atomic context, secondly this memory is not used for DMA.
Also removed some unneeded casts.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Cc: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes the following needlessly global functions static:
- __iscsi_unblock_session()
- iscsi_session_state_name()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes the needlessly global lpfc_disable_node() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This fixes a bug that can't handle a passthru command with more than
two sg entries.
Big thanks to Tim Pepper for debugging the problem.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
that provided by the block layer
ATA requires that all DMA transfers begin and end on word boundaries.
Because of this, a large amount of machinery grew up in ide to adjust
scatterlists on this basis. However, as of 2.5, the block layer has a
dma_alignment variable which ensures both the beginning and length of a
DMA transfer are aligned on the dma_alignment boundary. Although the
block layer does adjust the beginning of the transfer to ensure this
happens, it doesn't actually adjust the length, it merely makes sure
that space is allocated for transfers beyond the declared length. The
upshot of this is that scatterlists may be padded to any size between
the actual length and the length adjusted to the dma_alignment safely
knowing that memory is allocated in this region.
Right at the moment, SCSI takes the default dma_aligment which is on a
512 byte boundary. Note that this aligment only applies to transfers
coming in from user space. However, since all kernel allocations are
automatically aligned on a minimum of 32 byte boundaries, it is safe to
adjust them in this manner as well.
tj: * Adjusting sg after padding is done in block layer. Make libata
set queue alignment correctly for ATAPI devices and drop broken
sg mangling from ata_sg_setup().
* Use request->raw_data_len for ATAPI transfer chunk size.
* Killed qc->raw_nbytes.
* Separated out killing qc->n_iter.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With padding and draining moved into it, block layer now may extend
requests as directed by queue parameters, so now a request has two
sizes - the original request size and the extended size which matches
the size of area pointed to by bios and later by sgs. The latter size
is what lower layers are primarily interested in when allocating,
filling up DMA tables and setting up the controller.
Both padding and draining extend the data area to accomodate
controller characteristics. As any controller which speaks SCSI can
handle underflows, feeding larger data area is safe.
So, this patch makes the primary data length field, request->data_len,
indicate the size of full data area and add a separate length field,
request->raw_data_len, for the unmodified request size. The latter is
used to report to higher layer (userland) and where the original
request size should be fed to the controller or device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The spinlock is held over too large a region: pscratch is a permanent
address (it's allocated at boot time and never changes). All you need
the smp lock for is mediating the scratch in use flag, so fix this by
moving the spinlock into the case where we set the pscratch_busy flag
to false.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi/qla2xxx/qla_dfs.c: In function 'qla2x00_dfs_fce_show':
scsi/qla2xxx/qla_dfs.c:26: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'uint64_t'
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The panic occurs if we get a MSGIN or MSGOUT for an unidentified SCB
(meaning we didn't identify the outstanding command it was for). For
MSGIN this is wrong because it could be an unsolicited negotiation
MSGIN from the target.
Still panic on unsolicited MSGOUT because this would represent a
mistake in the negotiation phases. However, we should fix this as
well. The specs say we should go to bus free for unexpected msgin.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_debug does at several places:
for_each_sg(sdb->table.sgl, sg, sdb->table.nents, k) {
kaddr = (unsigned char *)
kmap_atomic(sg_page(sg), KM_USER0);
We cannot do something like that with the clustering enabled (or we
can use scsi_kmap_atomic_sg).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Apparently the fix to [SCSI] fas216: Use scsi_eh API for REQUEST_SENSE
invocation didn't show up in the final version sent to linus.
Correct this omission.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
From conversations with the maintainers the _p isn't needed so kill it.
That removes the last non ISA _p user from the SCSI layer to my knowledge.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This driver has been failing under heavy load with
aic94xx: escb_tasklet_complete: REQ_TASK_ABORT, reason=0x6
aic94xx: escb_tasklet_complete: Can't find task (tc=4) to abort!
The second message is because the driver fails to identify the task
it's being asked to abort. On closer inpection, there's a thinko in
the for each task loop over pending tasks in both the REQ_TASK_ABORT
and REQ_DEVICE_RESET cases where it doesn't look at the task on the
pending list but at the one on the ESCB (which is always NULL).
Fix by looking at the right task. Also add a print for the case where
the pending SCB doesn't have a task attached.
Not sure if this will fix all the problems, but it's a definite first
step.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
one system: initrd get courrupted:
RAMDISK: Compressed image found at block 0
RAMDISK: incomplete write (-28 != 2048) 134217728
crc error
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 388k freed
init_special_inode: bogus i_mode (177777)
Warning: unable to open an initial console.
init_special_inode: bogus i_mode (177777)
init_special_inode: bogus i_mode (177777)
Kernel panic - not syncing: No init found. Try passing init= option to kernel.
bisected to
commit 9927c68864
Author: James Bottomley <James.Bottomley@HansenPartnership.com>
Date: Sun Feb 3 15:48:56 2008 -0600
[SCSI] ses: add new Enclosure ULD
changes:
1. change char to unsigned char to avoid type change later.
2. preserve len for page1
3. need to move desc_ptr even the entry is not enclosure_component_device/raid.
so keep desc_ptr on right position
4. record page7 len, and double check if desc_ptr out of boundary before touch.
5. fix typo in subenclosure checking: should use hdr_buf instead.
[jejb: style fixes]
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix compilation warning in gdth.c, which was using the deprecated
pci_find_device.
drivers/scsi/gdth.c:645: warning: 'pci_find_device' is deprecated (declared at include/linux/pci.h:495)
Changing it to use pci_get_device, instead.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The patch: "gdth: switch to modern scsi host registration"
missed one simple fact when moving a way from scsi_module.c.
That is to call scsi_scan_host() on the probed host.
With this the gdth driver from 2.6.24 is again able to
see drives and boot.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Tested-by: Joerg Dorchain <joerg@dorchain.net>
Tested-by: Stefan Priebe <s.priebe@allied-internet.ag>
Tested-by: Jon Chelton <jchelton@ffpglobal.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
It looks like there's been a bug in the module parameter setup forever.
The upshot doesn't really matter, because even if no parameters are ever
set, we just call sym53c416_setup() three times, but the zero values in
the arrays eventually cause nothing to happen. Unfortunately gcc has
started to notice this now too:
drivers/scsi/sym53c416.c: In function 'sym53c416_detect':
drivers/scsi/sym53c416.c:624: warning: the address of 'sym53c416' will always evaluate as 'true'
drivers/scsi/sym53c416.c:630: warning: the address of 'sym53c416_1' will always evaluate as 'true'
drivers/scsi/sym53c416.c:636: warning: the address of 'sym53c416_2' will always evaluate as 'true'
drivers/scsi/sym53c416.c:642: warning: the address of 'sym53c416_3' will always evaluate as 'true'
So fix this longstanding bug to keep gcc quiet.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update lpfc driver version to 8.2.5
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous fixes:
- Fix ERRATT flag which was overlapping
- Allow RESTART mbx commands through when stopped.
- Accept incoming PLOGI when connected to an N_Port.
- Fix NPort to NPort pt2pt problems: ADISC and reg_vpi issues
- Fix vport unloading error that erroneously cleaned up RSCN buffers
- Fix memory leak during repeated unloads - in mbox handling
- Fix link bounce vs FLOGI race conditions
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Correct ndlp referencing issues:
- Fix ndlp kref issues due to race conditions between threads
- Fix cancel els delay retry event which missed an ndlp reference count
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
include/scsi/scsi.h as a definition:
#define ABORT_TASK 0x0d
on the other hand drivers/scsi/aic94xx/aic94xx_sas.h has:
#define ABORT_TASK 0x03
rename the latter to SCB_ABORT_TASK
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use new scsi_eh_prep/restor_cmnd() for synchronous REQUEST_SENSE
invocation. This also converts the driver to the new accessor based
scatterlist implementation.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
fix leaking with scomp leaking when failing. Also free page10 on
driver removal and remove one extra space.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some sysfs problems reported. The serial number on late model
controllers was truncated. Non-DASD devices (tapes and CDROMs) were
showing up as JBOD in the level report on the physical channel.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Adapter's Ignore Reset flag and insmod parameter boolean polarity
is incorrect in the driver.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added support for MSI utilizing the aacraid.msi=1 parameter. This
patch adds some localized or like-minded janitor fixes. Since the
default is disabled, there is no impact on the code paths unless the
customer wishes to experiment with the MSI performance.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The MegaRAID driver's common management module (megaraid_mm.c) creates a
char device used by the management tool "megarc" from LSI Logic (and
possibly other management tools).
In 2.6 with udev, this device doesn't get created because it is not
registered in sysfs.
I first fixed this by registering a class "megaraid_mm", but realized that
this should probably be moved to misc devices, instead of taking up a char
major. This is because only 1 device is used, even if there are multiple
adapters - the minor is never used (the adapter info is in the ioctl block
sent to the driver, not detected based on the minor number as one might
think). So it is a complete waste to have an entire major taken by this.
So it now uses a misc device which I named "megadev0" (the name that megarc
expects), and has a dynamic minor (previoulsy a dynamic major was used).
I have tested this on my own system with the megarc tool, and it works just
as fine as before (only now the device gets created correctly by udev).
Acked-by: "Patro, Sumant" <Sumant.Patro@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
struct asc_dvc_var needs overrun buffer to be placed on an 8 byte
boundary. advansys defines struct asc_dvc_var:
struct asc_dvc_var {
...
uchar overrun_buf[ASC_OVERRUN_BSIZE] __aligned(8);
The problem is that struct asc_dvc_var is placed on
shost->hostdata. So if the hostdata is not on an 8 byte boundary, the
advansys crashes. The hostdata is placed on a sizeof(unsigned long)
boundary so the 8 byte boundary is not garanteed with x86_32.
With 2.6.23 and 2.6.24, the hostdata is on an 8 byte boundary by
chance, but with the current git, it's not.
This patch removes overrun_buf static array and use kzalloc.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix bug introduced by my latest fix to the aic7xxx Makefile.
Test build on x86 32 and 64 bit.
Without and with -j (parallel build)
Building firmaware is br0ken with O=... but this
is unrelated to this bug-fix.
Tested-by: Adrian Bunk <bunk@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Douglas Gilbert <dougg@torque.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Luben Tuikov [mailto:ltuikov@yahoo.com] sez:
> Just as in your case and Tony's case, which I presume
> uses the same RAID firmware vendor, it would've
> probably been better if the RAID firmware vendor
> fixed the firmware to not set the VALID bit if the
> INFORMATION field is not valid.
Point taken regarding the aacraid driver. Dropped the VALID bit, and
then did some cleanup/simplification of the set_sense procedure and
the associated parameters. Mike did some preliminary tests when the
VALID bit was dropped before the 'Re: [PATCH] [SCSI] sd: make error
handling more robust' patches came on the scene. The change in the
SCSI subsystem does make this enclosed aacraid patch unnecessary, so
this aacraid patch is merely post battle ground cleanup. If the
simplification is an issue, repugnant, too much for a back-port to the
stable trees or clouds the point, this patch could be happily
distilled down to:
diff -ru a/drivers/scsi/aacraid/aachba.c b/drivers/scsi/aacraid/aachba.c
--- a/drivers/scsi/aacraid/aachba.c 2008-02-06 16:26:45.834938955 -0500
+++ b/drivers/scsi/aacraid/aachba.c 2008-02-06 16:32:01.109035329 -0500
@@ -865,7 +865,7 @@
u32 residue)
{
- sense_buf[0] = 0xF0; /* Sense data valid, err code 70h (current error) */
+ sense_buf[0] = 0x70; /* Sense data invalid, err code 70h (current error) */
sense_buf[1] = 0; /* Segment number, always zero */
if (incorrect_length) {
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds support to SCSI for enclosure services devices. It also makes
use of the enclosure services added in an earlier patch to display the
enclosure topology in sysfs.
At the moment, the enclosures are SAS specific, but if anyone actually
has a non-SAS enclosure that follows the SES-2 standard, we can add that
as well.
On my Vitesse based system, the enclosures show up like this:
sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/
total 0
-r--r--r-- 1 root root 4096 2008-02-03 15:44 components
lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005
lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure
--w------- 1 root root 4096 2008-02-03 15:44 uevent
And the individual occupied slots like this:
sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/
total 0
-rw-r--r-- 1 root root 4096 2008-02-03 15:45 active
lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0
-rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault
-rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate
-rw-r--r-- 1 root root 4096 2008-02-03 15:45 status
lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component
-r--r--r-- 1 root root 4096 2008-02-03 15:45 type
--w------- 1 root root 4096 2008-02-03 15:45 uevent
You can flash the various blinky lights by echoing to the fault and locate files.
>From the device's point of view, you can see it has an enclosure like this:
sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/
block:sda generic queue_depth state
bsg:0:0:0:0 iocounterbits queue_type subsystem
bus iodone_cnt rescan timeout
delete ioerr_cnt rev type
device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent
driver modalias scsi_disk:0:0:0:0 vendor
enclosure_component:SLOT 001 model scsi_generic:sg0
evt_media_change power scsi_level
Note the enclosure_component:SLOT 001 which shows where in the enclosure
this device fits.
The astute will notice that I'm using SCSI VPD Inquiries to identify the
devices. This, unfortunately, won't work for SATA devices unless we do
some really nasty hacking about on the SAT because the only think that
knows the SAS addresses for SATA devices is libsas, not libata where the
SAT resides.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 210ba1d172 updated sr.c to use
the scsi_test_unit_ready() function. Unfortunately, this has the
wrong characteristic of eating NOT_READY returns which sr.c relies on
for tray status.
Fix by rolling an internal sr_test_unit_ready() that doesn't do this.
Tested-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Direction of data transfer 'DMA_FROM_DEVICE' was tested twice. DTD_OUT
means transfer from host to device. This should occur when the
direction of data transfer (sc_data_direction) is 'DMA_TO_DEVICE'.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch ensures that the modern adapters get a maximum sg segment
size on par with the maximum transfer size. Added some localized
janitor fixes to the discussion patch I used with Fujita.
FUJITA Tomonori [mailto:fujita.tomonori@lab.ntt.co.jp] sez:
> I think that setting the proper maximum segment size for the late
> model cards (as you did above) makes sense.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When sending a SCSI command to a tape drive via the SCSI Generic (sg)
driver, if the command has a data transfer length more than
scatter_elem_sz (32 KB default) and not a multiple of 512, then I either
hit BUG_ON(!valid_dma_direction(direction)) in dma_unmap_sg() or else
the command never completes (depending on the LLDD).
When constructing scatterlists, the sg driver rounds up the scatterlist
element sizes to be a multiple of 512. This can result in
sum(scatterlist lengths) > bufflen. In this case, scsi_req_map_sg()
incorrectly sets bio->bi_size to sum(scatterlist lengths) rather than to
bufflen. When the command completes, req_bio_endio() detects that
bio->bi_size != 0, and so it doesn't call bio_endio(). This causes the
command to be resubmitted, resulting in BUG_ON or the command never
completing.
This patch makes scsi_req_map_sg() set bio->bi_size to bufflen rather
than to sum(scatterlist lengths), which fixes the problem.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- add arcmsr_enable_eoi_mode()and readl(reg->iop2drv_doorbell_reg) in
arcmsr_handle_hbb_isr() on adapter Type B in case of the doorbell
interrupt clearance is cached
- add conditional declaration for arcmsr_pci_error_detected() and
arcmsr_pci_slot_reset
- check if the sg list member number exceeds arcmsr default limit in
arcmsr_build_ccb()
- change the returned value type of arcmsr_build_ccb()from "void" to
"int" returns FAILED in arcmsr_queue_command()
- modify arcmsr_drain_donequeue() to ignore unknown command and let
kernel process command timeout. This could handle IO request violating
maximum segments, i.e. Linux XFS over DM-CRYPT. Thanks to Milan Broz's
comments <mbroz@redhat.com>
- fix the release of dma memory for type B in arcmsr_free_ccb_pool()
- fix the arcmsr_polling_hbb_ccbdone()
Signed-off-by: Nick Cheng <nick.cheng@areca.com.tw>
Cc: Milan Broz <mbroz@redhat.com>
Cc: <thenzl@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
drivers/scsi/dc395x.c: In function 'dc395x_init_one':
drivers/scsi/dc395x.c:4270: warning: 'ptr' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
These drivers depend on the deprecated NCR53C9X core and need to be converted
to the esp_scsi core.
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Linux/m68k <linux-m68k@vger.kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This driver depends on the deprecated NCR53C9X core and needs to be converted
to the esp_scsi core.
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add missing function parameter descriptions.
Make function short description fit on one line as required.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some devices report medium error locations incorrectly. Add guards to
make sure the reported bad lba is actually in the request that caused
it. Additionally remove the large case statment for sector sizes and
replace it with the proper u64 divisions.
Tested-by: Mike Snitzer <snitzer@gmail.com>
Cc: Stable Tree <stable@kernel.org>
Cc: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
BIT_2 of the firmware attributes is only valid on FW-interface-2
type HBAs. Code in commit
c48339decc would cause the
incorrect initialize-firmware mailbox command to be issued for
non-NPIV capable ISPs. Correct this by reverting to previously
used (and correct) pre-condition 'if' check.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For following fc_host specific attributes, vports rely on the pport.
So, this patch changed way to access the data for those attributes so that
they can access pport's.
- get_host_speed (speed)
- get_host_port_state (port_state)
- get_host_port_type (port_type)
- get_fc_host_stats
Also, added PORT_SPEED_8GB case in the speed attribute for 8Gb HBAs.
Signed-Off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
While running IO simultaneously through physical port and virtual
port, if user changes Data Rate (from scli utility), IO through
virtual port fails. It failed because the vport had not received
the ISP_ABORT_NEEDED notification.
Signed-Off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's no functional change involved with this update, instead
it simply migrates the "set cleared interrupt state" codes to a
more approprate method, qla2x00_request_irqs(), and cleans-up the
driver's probe() logic.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Collapse duplicate codes called during probe() and RISC-reset
into qla2x00_setup_chip().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Drop loop-till-allocated structure of code within
qla2x00_mem_alloc().
- Properly unwind deallcations of memory during failures.
- Drop qla2x00_allocate_sp_pool() and qla2x00_free_sp_pool()
functions as their implementations can easily be collapsed into
the callers.
- Defer DMA pool allocation of SFP data until requested.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
To insure that there is no stale data present during EFT
re-registration.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Refactor SRB-failure completion codes in the process. Also,
signal the DPC routine to complete sooner as backend processing
at shutdown-time is superflous.
[jejb: resolve conflicts with pci_enable_device_bars removal]
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Hmm, it looks like the conversion to resource_size_t usage
(3776541d8a) requires some additional
fixups to cleanup the structure-pointer castings used during IO mapped
accesses to the chip.
There's only a small number of locations, where the driver uses IO
mapped accesses to the hardware, the patch below should take care of
it without introducing to many structural changes to code flow.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set iscsi version to 2.0-868
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The session age mask is only 4 bits, but session->age is 32. When
it gets larger then 15 and we try to or the bits some bits get
dropped and the check for session age in iscsi_verify_itt is useless.
The ISCSI_CID_MASK related bits are also useless since cid is always
one.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some iscsi class messages have the dev_printk prefix and some libiscsi
and iscsi_tcp messages have "iscsi" or the module name as a prefix which
is normally pretty useless when trying to figure out which session
or connection the message is attached to. This patch adds iscsi lib
and class dev_printks so all messages have a common prefix that
can be used to figure out which object printed it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There are 13 iscsi conn attrs, but since the IF/OF markers were not being
used we did not notice that we forgot to increment the ISCSI_CONN_ATTRS
counter.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we rollover then we could get a next_timeout of zero, so we need
to set the new timer to that value.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
qla4xxx has the old school startup/probe where it finds presetup sessions
in its flash and then attempts to log into them before returning from the
probe. This however, makes it very simple to add a iscsi class scan finished
helper which the driver can use.
In future patches Dave or I will rip apart the driver to make it more
like qla2xxx, but for now this is a very simple two line patch which
fixes the problem of trying to figure out when the initial sessions
are done being scanned.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In qla4xxx's probe it will call the iscsi session setup functions
for session that got setup on the initial start. This then makes
it easy for the iscsi class to export a helper which indicates
when those scans are done.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If qla4xxx is resetting up a session and the recovery timer
fires we do not want to just set it to dead, because
the dpc thread could have just set it to online and is in the
middle of resetting it up.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This just adds iscsi session scanning which works like fc rport scanning.
The future patches will hook the drivers into Mathew Wilcox's async
scanning infrastructure, so userspace does not have to special case
iscsi and so userspace does not have to make a extra special case for
hardware iscsi root scanning.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This has qla4xxx use the iscsi class's check ready function
in the queue command function, so all iscsi drivers return the
same error value for common problems.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Qla4xxx can just call the iscsi recovery functions directly.
There is no need for userspace to do this for qla4xxx, because
we do not use the mutex to iterate over devices anymore and iscsi_block
/unblock_session can be called from interrupt context or the dpc thread.
And having userspace do this just creates uneeded headaches for qla4xxx root
situations where the session may experience problems. For example
during the kernel shutdown the scsi layer wants to send sync caches, but at
this time userspace is not up (iscsid is not running), so we cannot
recover from the problem.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds a iscsi session state file which exports the session
state for both software and hardware iscsi. It also hooks libiscsi
in.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- convert to accessors and !use_sg cleanup
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This driver depends on the deprecated NCR53C9X core and needs to be converted
to the esp_scsi core.
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes the calculation of the data transfer residual for the
case of a command that is supposed to transfer an odd number of bytes on
a wide bus but transfers nothing instead.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
It should be desired that 64 KiB is available for ATAPI transferrring.
(Historically) in SCSI/block layer sector size is defined as 512 during
sector-byte calculation.
Originally in ps3rom.c CD_FRAMESIZE (2048) was used, which limited
/sys/block/sr0/queue/max_sectors_kb to 16 KiB (32 sectors).
Signed-off-by: Aegis Lin <aegislin@gmail.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Converted sun3x_esp driver to use esp_scsi.c
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
__iscsi_complete_pdu() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The first patch (a119ee8ee3) was a bit
too aggressive and nested the locks (!) unit testing was in
error. This patch was reverted by
203a512f09.
This new patch should fix the locks correctly.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After the APUS removal, some code can be removed.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a one-line patch to add the following to __scsi_alloc_queue():
dma_set_seg_boundary(dev, shost->dma_boundary);
This is the simplest approach but the result looks odd,
__scsi_alloc_queue() does:
blk_queue_segment_boundary(q, shost->dma_boundary);
dma_set_seg_boundary(dev, shost->dma_boundary);
blk_queue_max_segment_size(q, dma_get_max_seg_size(dev));
I think that it would be better to set up segment boundary in the same
way as we did for the maximum segment size. That is, removing
shost->dma_boundary and LLDs call pci_set_dma_seg_boundary (or its
friends).
Then __scsi_alloc_queue() can set up both limits in the same way:
blk_queue_segment_boundary(q, dma_get_seg_boundary(dev));
blk_queue_max_segment_size(q, dma_get_max_seg_size(dev));
killing dma_boundary in scsi_host_template needs a large patch for
libata (dma_boundary is used by only libata and sym53c8xx). I'll send
a patch to do that if it is acceptable. James and Jeff?
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This sets the segment size limit properly via pci_set_dma_max_seg_size
and remove blk_queue_max_segment_size because scsi-ml calls it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
request_queue and device struct must have the same value of a segment
size limit. This patch adds blk_queue_segment_boundary in
__scsi_alloc_queue so LLDs don't need to call both
blk_queue_segment_boundary and set_dma_max_seg_size. A LLD can change
the default value (64KB) can call device_dma_parameters accessors like
pci_set_dma_max_seg_size when allocating scsi_host.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the io_req_t members to unsigned int, to allow use on machines with
more than 16 bits worth of IO ports (i.e. secondary busses on ppc64, etc).
There was only a couple of places in drivers where a change was needed. I
left printk formats alone (there are lots of %04x-style formats in there),
mostly to not change the format on the platforms that only have 16-bit io
addresses, but also because the padding doesn't really add all that much value
most of the time.
I found only one sprintf of an address, and upsized the string accordingly (I
doubt anyone will have anywhere near INT_MAX as irq value, but at least
there's room for it now).
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
scsi: fix dependency bug in aic7 Makefile
kbuild: add svn revision information to setlocalversion
kbuild: do not warn about __*init/__*exit symbols being exported
Move Kconfig.instrumentation to arch/Kconfig and init/Kconfig
Add HAVE_KPROBES
Add HAVE_OPROFILE
Create arch/Kconfig
Fix ARM to play nicely with generic Instrumentation menu
kconfig: ignore select of unknown symbol
kconfig: mark config as changed when loading an alternate config
kbuild: Spelling/grammar fixes for config DEBUG_SECTION_MISMATCH
Remove __INIT_REFOK and __INITDATA_REFOK
kbuild: print only total number of section mismatces found
Building the aic7xxx driver includes the copy
of an .h file from a _shipped file.
In a highly parallel build Ingo saw that the
build sometimes failed (included distcc usage).
It was tracked down to a missing dependency from the .c
source file to the generated .h file.
We started to build the .c file before the
copy (cat) operation of the .h file completed
and we then only got half of the definitions
from the copied .h file.
Add an explicit dependency from the .c files to the
generated .h files so make knows all dependencies and
finsih the build of the .h files before it starts
building the .o files.
Ingo tested this fix and reported:
good news: hundreds of successful kernel builds and no failures
overnight.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Acked-by: James Smart <james.smart@emulex.com>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: David Somayajulu <david.somayajulu@qlogic.com>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Based on a patch from Ingo Molnar <mingo@elte.hu> as he pointed out that
I wrongly missed this.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SELECT_DRIVE() is called by IDE core code in start_request() before device
driver's ->do_request method. In ide-scsi case ->do_request is implemented
by idescsi_do_request() which is also the only user of idescsi_issue_pc().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (64 commits)
PCI: make pci_bus a struct device
PCI: fix codingstyle issues in include/linux/pci.h
PCI: fix codingstyle issues in drivers/pci/pci.h
PCI: PCIE ASPM support
PCI: Fix fakephp deadlock
PCI: modify SB700 SATA MSI quirk
PCI: Run ACPI _OSC method on root bridges only
PCI ACPI: AER driver should only register PCIe devices with _OSC
PCI ACPI: Added a function to register _OSC with only PCIe devices.
PCI: constify function pointer tables
PCI: Convert drivers/pci/proc.c to use unlocked_ioctl
pciehp: block new requests from the device before power off
pciehp: workaround against Bad DLLP during power off
pciehp: wait for 1000ms before LED operation after power off
PCI: Remove pci_enable_device_bars() from documentation
PCI: Remove pci_enable_device_bars()
PCI: Remove users of pci_enable_device_bars()
PCI: Add pci_enable_device_{io,mem} intefaces
PCI: avoid save the same type of cap multiple times
PCI: correctly initialize a structure for pcie_save_pcix_state()
...
This patch converts users of pci_enable_device_bars() to the new
pci_enable_device_{io,mem} interface.
The new API fits nicely, except maybe for the QLA case where a bit of
code re-organization might be a good idea but I prefer sticking to the
simple patch as I don't have hardware to test on.
I'll also need some feedback on the cs5520 change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Delete filenames/versions from comments.
I'm leaving decisions about adding DRV_VERSION defines and MODULE_VERSION()-s
to maintainers of the respective drivers.
While at it:
* Remove unused VERSION define from ide.c.
* Remove unused/stale DRV_VERSION define from au1xxx-ide.c.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
