Add sdhci support for MACCHIATOBin boards. This uses the AP806 SDHCI
for eMMC and CP110 master for the SD card slot.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The XORv2 engines in the AP side of the Armada 7K/8K SoCs are using the
AP MS core clock as input, so this commit adds the appropriate clocks
properties.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add nodes for the SPICC controller on GX common dtsi, GXBB and
GXL dtsi files.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add entry for k3-dma driver and i2s/hdmi audio devices.
This enables HDMI audio output.
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Andy Green <andy@warmcat.com>
Cc: Dave Long <dave.long@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Antonio Borneo <borneo.antonio@gmail.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
v2:
* Split core i2s entry into dtsi and hdmi specific bits into
hikey dts
v4:
* Rework simple-card to use many-dai-links method, as
there may be other links in the future
v5:
* Rework audio description to use the audio-card-graph method
as requested by Mark.
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add nodes for WiFi. HiKey960 is using TI WL1837MOD module.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The Hi3660 SoC comes with the sp804 timer in addition to the
architecture timers. These ones are shutdown when reaching a deep idle
states and a backup timer is needed. The sp804 belongs to another power
domain and can fulfill the purpose of replacing temporarily an
architecture timer when the CPU is idle.
Describe it in the device tree, so it can be enabled at boot time.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add spi2 and spi3 device nodes for hi3660, and enable them for hikey960.
On HiKey960:
- SPI2 is wired out through low speed expansion connector.
- SPI3 is wired out through high speed expansion connector.
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
HiKey960 has four user LEDs, and two special purpose LEDs: WiFi and BT
respectively.
All of them are implemented as GPIO.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
We use gpio_034 as power key on hikey960, and set gpio with pull-up
state, when key press the voltage on the gpio will come to lower, and
power key event will be reported.
Signed-off-by: Chen Jun <chenjun14@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This adds the serial slave device for the WL1837 Bluetooth interface.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add nodes uart0 to uart4 and uart6 for hi3660 SoC.
Enable uart3 and uart6, disable uart5, in hikey960 board dts.
On HiKey960:
- UART6 is used as default console, and is wired out through low speed
expansion connector.
- UART3 has RTS/CTS hardware handshake, and is wired out through low
speed expansion connector.
- UART5 is not used in commercial launched boards. So disable it.
- UART4 is connected to Bluetooth, WL1837.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Reviewed-by: Zhangfei Gao <zhangfei.gao@hisilicon.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add I2C nodes for Hi3660-hikey960.
On HiKey960,
I2C0, I2C7 are connected to Low Speed Expansion Connector.
I2C1 is connected to ADV7535.
I2C3 is connected to USB5734.
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add some resource nodes for clock and reset
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This commit adds more pinmux and pinctrl information for devices
on HiKey960, including i2c, spi, cam, uart, ufs, pcie, csi, pwr_key,
isp, sd/sdio, i2s, and usb.
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Signed-off-by: Chen Jun <chenjun14@huawei.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Update compatible string for hikey960. HiKey960 is a develpment board built
with SoC Hi3660.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Note that the audio module has resets for the Serial Sound Interfaces
only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Note that the audio module has resets for the Serial Sound Interfaces
only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(improving storage performance and leaving sdhci for wireless), and
the correct CPU thermal coefficients.
The thermal changes required a merge from bcm2835-dt-next, where the
nodes were added.
-----BEGIN PGP SIGNATURE-----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=juQA
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=oIYF
-----END PGP SIGNATURE-----
Merge tag 'bcm2835-dt-64-next-2017-06-08' into devicetree-arm64/next
This pull request brings in the switch to sdhost for MMC on RPi3
(improving storage performance and leaving sdhci for wireless), and
the correct CPU thermal coefficients.
The thermal changes required a merge from bcm2835-dt-next, where the
nodes were added.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Tegra186 CCPLEX_CLUSTER area contains memory-mapped
registers that initiate CPU frequency/voltage transitions.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Orangepi Zero Plus 2 is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Zero Plus 2 has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG+power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.
A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A53 64bit
- 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
- Debug TTL UART
- Four USB 2.0
- HDMI
- LCD
- Audio and MIC
- Wifi + BT
- IR receiver
- 5V DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add initial device tree support for LD20 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add initial device tree support for LD11 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add initial support for the Renesas Salvator-XS (Salvator-X 2nd version)
development board equipped with an R-Car H3 ES2.0 SiP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Renesas Salvator-XS (Salvator-X 2nd version) development board can
be equipped with either an R-Car H3 ES2.0 or M3-W ES1.x SiP, which are
pin-compatible.
Add initial support for the common parts of the Salvator-XS board into
its own .dtsi file, to be included by the DTSes for the H3/M3-W
versions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Renesas Salvator-X and Salvator-XS (Salvator-X 2nd version) boards
are very similar. To avoid duplication, prepare for the advent of the
latter by extracting the common board parts into its own .dtsi file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car Gen3 SoCs contain multiple PWM modules. Hence to avoid conflicts,
pinctrl subnodes for PWM should include indices referring to their
instances.
Fixes: b33be33670 ("arm64: dts: salvator-x: Add panel backlight support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Split off support for H3ULCB boards with the ES1.x revision of the R-Car
H3 SoC into a separate file. The main r8a7795-h3ulcb.dts file now
corresponds to H3ULCB with R-Car H3 ES2.0 or later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tested with a Salvator-X.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tested with a Salvator-X.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current rcar_sound only has 11289600 (= for 44.1kHz) clock-frequency,
but it needs 12288000 for 48kHz too.
Otherwise, 48kHz based sound can't handle correctly.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current rcar_sound only has 11289600 (= for 44.1kHz) clock-frequency,
but it needs 12288000 for 48kHz too.
Otherwise, 48kHz based sound can't handle correctly.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add HDMI and CVBS nodes for the Amlogic P212 reference board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add HDMI and CVBS nodes for the Wetek Play2 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds device tree node for USB Dual Role Device PHY for
Broadcom's Northstar2 SoC.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This defines the bcm2837 SoC specific thermal coefficients in
order to initialize the thermal driver correctly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
If the mdp_* nodes are under an mdp sub-node, their corresponding
platform device does not automatically get its iommu assigned properly.
Fix this by moving the mdp component nodes up a level such that they are
siblings of mdp and all other SoC subsystems. This also simplifies the
device tree.
Although it fixes iommu assignment issue, it also break compatibility
with old device tree. So, the patch in driver is needed to iterate over
sibling mdp device nodes, not child ones, to keep driver work properly.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Minghsiu Tsai <minghsiu.tsai@mediatek.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Follow the recent trend for the license description, and fix the wrongly
stated X11 to MIT.
The X11 license text [1] is explicitly for the X Consortium and has a
couple of extra clauses. The MIT license text [2] is actually what the
current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reserve enough space below the kernel base.
The assumed address map is:
80000000 - 80ffffff : for IPP
81000000 - 81ffffff : for ARM secure
82000000 - : for Linux
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add the required DT parts to enable Ethernet (dwmac-sun8i driver) on
the Nano Pi NEO2 board. It uses an external Realtek RTL8211E PHY
connected via RGMII to provide GbE network. Specially unlike other
Allwinner boards, the phy is connected to MDIO address 7, not 1.
This includes the regulator (which is controlled by a GPIO pin) and
the actual Ethernet MAC node, referring the RGMII pins of the device.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the required DT parts to enable Ethernet (dwmac-sun8i driver) on
the Orange Pi Prime board. It uses an external Realtek RTL8211E PHY
connected via RGMII to provide GbE network.
This includes the regulator (which is controlled by a GPIO pin) and
the actual Ethernet MAC node, referring the RGMII pins of the device.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The reg_vcc3v3 node is wrongly placed at the start of the / part, but
not with other fixed regulators used by the board, which makes the
device nodes unsorted.
As Orange Pi Prime and Nano Pi NEO2 device trees are copy'n'paste works,
they share the device node unsorted issue.
Fix this by move reg_vcc3v3 node to the position before reg_usb0_vbus.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pine64 have made an official baseboard when SoPine SoM is out.
The official baseboard is like the original Pine64 -- but with SD card
slot replaced with Pine64's eMMC module slot.
Add a device tree for SoPine with the baseboard.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the BananaPi M64.
It uses an external PHY rtl8211e via RGMII.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the pine64 plus.
It uses an external PHY rtl8211e via RGMII.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the pine64
It uses an external PHY via RMII.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i is an Ethernet MAC that supports 10/100/1000 Mbit
connections. It is very similar to the device found in the Allwinner
H3, but lacks the internal 100 Mbit PHY and its associated control
bits.
This adds the necessary bits to the Allwinner A64 SoC .dtsi, but keeps
it disabled at this level.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch add the dt node for the syscon register present on the
Allwinner A64.
Only two register are present in this syscon and the only one useful is
the one dedicated to EMAC clock.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
SoPine is a SoM by Pine64, which have a gold finger compatible with the
slot of DDR3 SODIMM (signals are not compatible), and have an A64, an
AXP803, a LPDDR3 DRAM chip, a power led and a MicroSD slot on it.
The card detect pin of the MicroSD slot on the SoM is pulled down, which
makes it unusable; however, the slot is at the surface of the SoM that
is closed to the baseboard, so it's nearly impossible to hot-swap it,
thus I make it non-removable.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A64 device tree file has some remnants of raw number references
to the CCU node, likely from when the CCU bindings and device tree
changes were first merged.
Convert these, and the R_CCU ones, to use the proper defined macros
from their respective device tree binding header files.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pine64 exposes all A64 UARTs, not just UART0.
Since the pins can be used as GPIO, don't enable the new UART nodes by
default, but prepare the pinctrl settings to aid in activating them via
overlays, i.e., overriding the status property of &uartX nodes.
For UART4 (Euler) the safer route of not including RTS/CTS pins is chosen,
whereas for UART1 (Bluetooth) they are included.
Add the corresponding pinctrl nodes where missing.
Suggested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 have a RSB controller like the one on A23/A33 SoCs.
Add it and its pinmux.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enabling uart2 node currently leads to a /dev/ttyS1 device, with ttyS0..4
always present, causing confusion on the user's part.
dtc cannot resolve an overlay's &uart2 reference for strings, only for
phandles, so it would need to hardcode the full node path.
Avoid this and enforce reliable numbering by adding serialX aliases for:
UART1 - on Wifi/BT connector
UART2 - on Pi-2 connector
UART3 - on Euler connector
UART4 - on Euler connector
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
UART2 is exposed on the Pi connector of Pine64. Make a pinctrl node
available at the SoC level, to simplify enabling UART2 via DT overlay.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
NanoPi NEO2 is a board with the same size factor with the original
NanoPi NEO by FriendlyELEC.
It has a H5 instead of H3 on NanoPi NEO, and the ethernet is upgraded to
1Gbps (with external RTL8211E PHY).
Add support for this board.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orange Pi Prime is a new Allwinner H5-based SBC by Xunlong.
It's like a Orange Pi Plus 2E with H3 replaced with H5, eMMC replaced
with onboard SPI NOR Flash and wireless card changed to Realtek
RTL8723BS (with Bluetooth functionality).
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Switch to use the new compatible for the SCPI sensors so that the
sensor readings are reported using the correct scale.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The dwmac-sun8i hardware is present on the Orange PI PC2.
It uses an external PHY rtl8211e via RGMII.
This patch create the needed regulator, emac and phy nodes.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The TX status trigger of the wlan interface is named phy0tx, so this
updates the default-trigger for the WLAN LED to use that instead.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the DT node for Kryo CPU clock controller on msm8996
devices.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
SMEM allows various subsystems/processors to share
memory/data (heap format) in order to enable various
peripherals.
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This regulator is not moving anywhere. Sit, stay...
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Stingray SoC has two instances of SDHCI controller
and one instance of iProc PWM.
Let's enable above mentioned devices in Stingray DT.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We have two instance of PL022 SPI controllers, one instance of
DMA PL330, and one non-secure SP805 Watchdog on Stingray SOC.
This patch adds DT nodes for the above mentioned devices in
Stingray DT.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Pramod KUMAR <pramod.kumar@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The GPIOs on Stingray SOC are based on iProc GPIOs hence
using this we add GPIO DT nodes for Stingray SOC.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch adds pinctrl and pinmux related DT nodes for
Stingray SOC.
For manageability, pinctrl and pinmum DT nodes are added
as separate DTSi file and included in main DTSi file.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Vikram Prakash <vikram.prakash@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch describes Stingray SOC clock tree using
DT nodes in Stingray DTS.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Broadcom Stingray SoC is a new member in Broadcom iProc
SoC family.
This patch adds initial DTS files for Broadcom Stingray SoC
and two of its reference boards (bcm958742k and bcm958742t).
We have lot of reference boards and large number of devices
in Broadcom Stingray SoC so eventually we will have quite
a few DTS files for Stingray. To tackle, we have added a
separate directory for Stingray DTS files.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
ls1012a has separate input root clocks for core PLLs versus the platform
PLL, with the latter described as sysclk in the hw docs.
Accordingly, update the clock-frequency in sysclk to 125M as platform
input clock.
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "dis_rxdet_inp3_quirk" boolean property to USB3 node. This property
is used to disable rx detection in P3 PHY mode.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently SD UHS-I modes were enabled by default on LS208xARDB boards,
but the new LS2088ARDB RevF board didn't support them any more since SDHC
circuit had been reworked. This patch is to disable SD UHS-I modes by default
in case of any issue on LS2088ARDB RevF
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds an initial DT for the RTD1295 SoC and a TV box based on it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vjlA
-----END PGP SIGNATURE-----
Merge tag 'realtek-arm64-dt-for-4.12' of git://github.com/afaerber/linux into next/dt64
Realtek ARM64 based SoC DT for v4.12
This adds an initial DT for the RTD1295 SoC and a TV box based on it.
* tag 'realtek-arm64-dt-for-4.12' of git://github.com/afaerber/linux:
ARM64: dts: Add Realtek RTD1295 and Zidoo X9S
dt-bindings: arm: Add Realtek RTD1295 bindings
dt-bindings: Add vendor prefix for Zidoo
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add support for R-Car H3 ES2.0
* Break out common board support
* Set drive-strength for ravb pins for r8a7795/h3ulcb and r8a7796/m3ulcb
* Enable HDMI outputs on r8a7795/salvator-x
* Add R-Car audio to DT of r8a7796 SoC
* Add current sense amplifiers to DT of r8a779[56]/salvator-x
* Enable NFS-root on r8a7796/salvator-x
* Enable HS200 for eMMC on r8a779[56]/salvator-x,
r8a7795/h3ulcb and r8a7796/m3ulcb
* Enable EthernetAVB, I2C r8a7796/m3ulcb
* Update memory node to 2 GiB map on r8a7796/m3ulcb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cmye
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Renesas ARM64 Based SoC DT Updates for v4.13
* Add support for R-Car H3 ES2.0
* Break out common board support
* Set drive-strength for ravb pins for r8a7795/h3ulcb and r8a7796/m3ulcb
* Enable HDMI outputs on r8a7795/salvator-x
* Add R-Car audio to DT of r8a7796 SoC
* Add current sense amplifiers to DT of r8a779[56]/salvator-x
* Enable NFS-root on r8a7796/salvator-x
* Enable HS200 for eMMC on r8a779[56]/salvator-x,
r8a7795/h3ulcb and r8a7796/m3ulcb
* Enable EthernetAVB, I2C r8a7796/m3ulcb
* Update memory node to 2 GiB map on r8a7796/m3ulcb
* tag 'renesas-arm64-dt-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (35 commits)
arm64: dts: r8a7795: salvator-x: Add support for R-Car H3 ES2.0
arm64: dts: r8a7795: Add support for R-Car H3 ES2.0
arm64: dts: ulcb: Set drive-strength for ravb pins
arm64: dts: renesas: r8a7795-salvator-x: Enable HDMI outputs
arm64: dts: renesas: r8a7795-salvator-x: Add DU external dot clocks
arm64: dts: renesas: salvator-x: Add HDMI output connectors
arm64: dts: renesas: salvator-x: Add DU external dot clock sources
arm64: dts: renesas: r8a7795: Add HDMI encoder support
arm64: dts: salvator-x: Add panel backlight support
arm64: dts: r8a7796: Add PWM device nodes
arm64: dts: r8a7796: add Sound MIX support
arm64: dts: r8a7796: add Sound CTU support
arm64: dts: r8a7796: add Sound DVC support
arm64: dts: r8a7796: add Sound SRC support
arm64: dts: r8a7796: add Sound SSI DMA support
arm64: dts: r8a7796: add Sound SSI PIO support
arm64: dts: r8a7796: add AUDIO_DMAC support
arm64: dts: salvator-x: Add current sense amplifiers
arm64: dts: renesas: Extract common ULCB board support
arm64: dts: renesas: Extract common Salvator-X board support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the SPICC Controller pins nodes for Amlogic GXL SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the SPICC Controller pins nodes for Amlogic GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic Meson GXL SoCs embeds an 10/100 Ethernet PHY, this patchs adds
the Link and Activity LEDs signals pins nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the AO and EE domain CEC pins nodes for the Amlogic Meson GXL SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the AO and EE domain CEC pins nodes for the Amlogic Meson GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The pull-enable register base was wrongly copied from the meson8b pinctrl node,
but was not used yet.
Fixes: c328666d58 ("ARM64: dts: amlogic: Add Meson GX dtsi from GXBB")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The pull-enable register base was wrongly copied from the GXBB pinctrl node,
but was not used yet.
Fixes: fb0fe92294 ("ARM64: dts: meson-gxl: Add pinctrl nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The gpio-range was badly added on the GXL dtsi, the AO pin count is 10
instead of 14.
Fixes: 84412e4e85 ("ARM64: dts: meson-gxl: Add gpio-ranges properties")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The FriendlyARM NanoPi K2 is a single-board computer.
Cc: techsupport@friendlyarm.com
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The R-Box Pro is a TV box derived from Amlogic q200 reference design.
It uses an AP6255 Wifi module. It features an LED tube that lights a
surrounding stripe and the top logo in blue or red or pink'ish - blue
is on by default, and red (i.e., pink) is configured as panic indicator.
This device is available in at least two models, with 2 GB vs. 3 GB RAM
as well as varying eMMC size. The intent is to handle this with a single
.dts that gets the actual RAM size from U-Boot.
Cc: ada@kingnoval.com
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The rk3399 has multiple variants with different frequency ratings.
The operating points currently in the kernel stem from the op1 variant
used in Gru ChromeOS devices and may not be suitable for general rk3399
chips. Therefore bring it back to the official general operating points.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The OP1 is a rk3399 variant used in ChromeOS devices with a slightly
higher frequency rating compared to the regular rk3399, but right now
the only available operating points don't match either variant
with both needing adjustments to actually fit their specs.
Therefore introduce separate operting points, from the ChromeOS kernel,
for the OP1 and use it on Gru devices.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>