Pull x86 pti updates from Thomas Gleixner:
"This contains:
- a PTI bugfix to avoid setting reserved CR3 bits when PCID is
disabled. This seems to cause issues on a virtual machine at least
and is incorrect according to the AMD manual.
- a PTI bugfix which disables the perf BTS facility if PTI is
enabled. The BTS AUX buffer is not globally visible and causes the
CPU to fault when the mapping disappears on switching CR3 to user
space. A full fix which restores BTS on PTI is non trivial and will
be worked on.
- PTI bugfixes for EFI and trusted boot which make sure that the user
space visible page table entries have the NX bit cleared
- removal of dead code in the PTI pagetable setup functions
- add PTI documentation
- add a selftest for vsyscall to verify that the kernel actually
implements what it advertises.
- a sysfs interface to expose vulnerability and mitigation
information so there is a coherent way for users to retrieve the
status.
- the initial spectre_v2 mitigations, aka retpoline:
+ The necessary ASM thunk and compiler support
+ The ASM variants of retpoline and the conversion of affected ASM
code
+ Make LFENCE serializing on AMD so it can be used as speculation
trap
+ The RSB fill after vmexit
- initial objtool support for retpoline
As I said in the status mail this is the most of the set of patches
which should go into 4.15 except two straight forward patches still on
hold:
- the retpoline add on of LFENCE which waits for ACKs
- the RSB fill after context switch
Both should be ready to go early next week and with that we'll have
covered the major holes of spectre_v2 and go back to normality"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
x86,perf: Disable intel_bts when PTI
security/Kconfig: Correct the Documentation reference for PTI
x86/pti: Fix !PCID and sanitize defines
selftests/x86: Add test_vsyscall
x86/retpoline: Fill return stack buffer on vmexit
x86/retpoline/irq32: Convert assembler indirect jumps
x86/retpoline/checksum32: Convert assembler indirect jumps
x86/retpoline/xen: Convert Xen hypercall indirect jumps
x86/retpoline/hyperv: Convert assembler indirect jumps
x86/retpoline/ftrace: Convert ftrace assembler indirect jumps
x86/retpoline/entry: Convert entry assembler indirect jumps
x86/retpoline/crypto: Convert crypto assembler indirect jumps
x86/spectre: Add boot time option to select Spectre v2 mitigation
x86/retpoline: Add initial retpoline support
objtool: Allow alternatives to be ignored
objtool: Detect jumps to retpoline thunks
x86/pti: Make unpoison of pgd for trusted boot work for real
x86/alternatives: Fix optimize_nops() checking
sysfs/cpu: Fix typos in vulnerability documentation
x86/cpu/AMD: Use LFENCE_RDTSC in preference to MFENCE_RDTSC
...
Add some details about how PTI works, what some of the downsides
are, and how to debug it when things go wrong.
Also document the kernel parameter: 'pti/nopti'.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Moritz Lipp <moritz.lipp@iaik.tugraz.at>
Cc: Daniel Gruss <daniel.gruss@iaik.tugraz.at>
Cc: Michael Schwarz <michael.schwarz@iaik.tugraz.at>
Cc: Richard Fellner <richard.fellner@student.tugraz.at>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andi Lutomirsky <luto@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180105174436.1BC6FA2B@viggo.jf.intel.com
Pull more x86 pti fixes from Thomas Gleixner:
"Another small stash of fixes for fallout from the PTI work:
- Fix the modules vs. KASAN breakage which was caused by making
MODULES_END depend of the fixmap size. That was done when the cpu
entry area moved into the fixmap, but now that we have a separate
map space for that this is causing more issues than it solves.
- Use the proper cache flush methods for the debugstore buffers as
they are mapped/unmapped during runtime and not statically mapped
at boot time like the rest of the cpu entry area.
- Make the map layout of the cpu_entry_area consistent for 4 and 5
level paging and fix the KASLR vaddr_end wreckage.
- Use PER_CPU_EXPORT for per cpu variable and while at it unbreak
nvidia gfx drivers by dropping the GPL export. The subject line of
the commit tells it the other way around, but I noticed that too
late.
- Fix the ASM alternative macros so they can be used in the middle of
an inline asm block.
- Rename the BUG_CPU_INSECURE flag to BUG_CPU_MELTDOWN so the attack
vector is properly identified. The Spectre mitigations will come
with their own bug bits later"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pti: Rename BUG_CPU_INSECURE to BUG_CPU_MELTDOWN
x86/alternatives: Add missing '\n' at end of ALTERNATIVE inline asm
x86/tlb: Drop the _GPL from the cpu_tlbstate export
x86/events/intel/ds: Use the proper cache flush method for mapping ds buffers
x86/kaslr: Fix the vaddr_end mess
x86/mm: Map cpu_entry_area at the same place on 4/5 level
x86/mm: Set MODULES_END to 0xffffffffff000000
vaddr_end for KASLR is only documented in the KASLR code itself and is
adjusted depending on config options. So it's not surprising that a change
of the memory layout causes KASLR to have the wrong vaddr_end. This can map
arbitrary stuff into other areas causing hard to understand problems.
Remove the whole ifdef magic and define the start of the cpu_entry_area to
be the end of the KASLR vaddr range.
Add documentation to that effect.
Fixes: 92a0f81d89 ("x86/cpu_entry_area: Move it out of the fixmap")
Reported-by: Benjamin Gilbert <benjamin.gilbert@coreos.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Benjamin Gilbert <benjamin.gilbert@coreos.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Garnier <thgarnie@google.com>,
Cc: Alexander Kuleshov <kuleshovmail@gmail.com>
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1801041320360.1771@nanos
There is no reason for 4 and 5 level pagetables to have a different
layout. It just makes determining vaddr_end for KASLR harder than
necessary.
Fixes: 92a0f81d89 ("x86/cpu_entry_area: Move it out of the fixmap")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Benjamin Gilbert <benjamin.gilbert@coreos.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Garnier <thgarnie@google.com>,
Cc: Alexander Kuleshov <kuleshovmail@gmail.com>
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1801041320360.1771@nanos
Since f06bdd4001 ("x86/mm: Adapt MODULES_END based on fixmap section size")
kasan_mem_to_shadow(MODULES_END) could be not aligned to a page boundary.
So passing page unaligned address to kasan_populate_zero_shadow() have two
possible effects:
1) It may leave one page hole in supposed to be populated area. After commit
21506525fb ("x86/kasan/64: Teach KASAN about the cpu_entry_area") that
hole happens to be in the shadow covering fixmap area and leads to crash:
BUG: unable to handle kernel paging request at fffffbffffe8ee04
RIP: 0010:check_memory_region+0x5c/0x190
Call Trace:
<NMI>
memcpy+0x1f/0x50
ghes_copy_tofrom_phys+0xab/0x180
ghes_read_estatus+0xfb/0x280
ghes_notify_nmi+0x2b2/0x410
nmi_handle+0x115/0x2c0
default_do_nmi+0x57/0x110
do_nmi+0xf8/0x150
end_repeat_nmi+0x1a/0x1e
Note, the crash likely disappeared after commit 92a0f81d89, which
changed kasan_populate_zero_shadow() call the way it was before
commit 21506525fb.
2) Attempt to load module near MODULES_END will fail, because
__vmalloc_node_range() called from kasan_module_alloc() will hit the
WARN_ON(!pte_none(*pte)) in the vmap_pte_range() and bail out with error.
To fix this we need to make kasan_mem_to_shadow(MODULES_END) page aligned
which means that MODULES_END should be 8*PAGE_SIZE aligned.
The whole point of commit f06bdd4001 was to move MODULES_END down if
NR_CPUS is big, so the cpu_entry_area takes a lot of space.
But since 92a0f81d89 ("x86/cpu_entry_area: Move it out of the fixmap")
the cpu_entry_area is no longer in fixmap, so we could just set
MODULES_END to a fixed 8*PAGE_SIZE aligned address.
Fixes: f06bdd4001 ("x86/mm: Adapt MODULES_END based on fixmap section size")
Reported-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Thomas Garnier <thgarnie@google.com>
Link: https://lkml.kernel.org/r/20171228160620.23818-1-aryabinin@virtuozzo.com
Pull x86 page table isolation updates from Thomas Gleixner:
"This is the final set of enabling page table isolation on x86:
- Infrastructure patches for handling the extra page tables.
- Patches which map the various bits and pieces which are required to
get in and out of user space into the user space visible page
tables.
- The required changes to have CR3 switching in the entry/exit code.
- Optimizations for the CR3 switching along with documentation how
the ASID/PCID mechanism works.
- Updates to dump pagetables to cover the user space page tables for
W+X scans and extra debugfs files to analyze both the kernel and
the user space visible page tables
The whole functionality is compile time controlled via a config switch
and can be turned on/off on the command line as well"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
x86/ldt: Make the LDT mapping RO
x86/mm/dump_pagetables: Allow dumping current pagetables
x86/mm/dump_pagetables: Check user space page table for WX pages
x86/mm/dump_pagetables: Add page table directory to the debugfs VFS hierarchy
x86/mm/pti: Add Kconfig
x86/dumpstack: Indicate in Oops whether PTI is configured and enabled
x86/mm: Clarify the whole ASID/kernel PCID/user PCID naming
x86/mm: Use INVPCID for __native_flush_tlb_single()
x86/mm: Optimize RESTORE_CR3
x86/mm: Use/Fix PCID to optimize user/kernel switches
x86/mm: Abstract switching CR3
x86/mm: Allow flushing for future ASID switches
x86/pti: Map the vsyscall page if needed
x86/pti: Put the LDT in its own PGD if PTI is on
x86/mm/64: Make a full PGD-entry size hole in the memory map
x86/events/intel/ds: Map debug buffers in cpu_entry_area
x86/cpu_entry_area: Add debugstore entries to cpu_entry_area
x86/mm/pti: Map ESPFIX into user space
x86/mm/pti: Share entry text PMD
x86/entry: Align entry text section to PMD boundary
...
With PTI enabled, the LDT must be mapped in the usermode tables somewhere.
The LDT is per process, i.e. per mm.
An earlier approach mapped the LDT on context switch into a fixmap area,
but that's a big overhead and exhausted the fixmap space when NR_CPUS got
big.
Take advantage of the fact that there is an address space hole which
provides a completely unused pgd. Use this pgd to manage per-mm LDT
mappings.
This has a down side: the LDT isn't (currently) randomized, and an attack
that can write the LDT is instant root due to call gates (thanks, AMD, for
leaving call gates in AMD64 but designing them wrong so they're only useful
for exploits). This can be mitigated by making the LDT read-only or
randomizing the mapping, either of which is strightforward on top of this
patch.
This will significantly slow down LDT users, but that shouldn't matter for
important workloads -- the LDT is only used by DOSEMU(2), Wine, and very
old libc implementations.
[ tglx: Cleaned it up. ]
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Shrink vmalloc space from 16384TiB to 12800TiB to enlarge the hole starting
at 0xff90000000000000 to be a full PGD entry.
A subsequent patch will use this hole for the pagetable isolation LDT
alias.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 PTI preparatory patches from Thomas Gleixner:
"Todays Advent calendar window contains twentyfour easy to digest
patches. The original plan was to have twenty three matching the date,
but a late fixup made that moot.
- Move the cpu_entry_area mapping out of the fixmap into a separate
address space. That's necessary because the fixmap becomes too big
with NRCPUS=8192 and this caused already subtle and hard to
diagnose failures.
The top most patch is fresh from today and cures a brain slip of
that tall grumpy german greybeard, who ignored the intricacies of
32bit wraparounds.
- Limit the number of CPUs on 32bit to 64. That's insane big already,
but at least it's small enough to prevent address space issues with
the cpu_entry_area map, which have been observed and debugged with
the fixmap code
- A few TLB flush fixes in various places plus documentation which of
the TLB functions should be used for what.
- Rename the SYSENTER stack to CPU_ENTRY_AREA stack as it is used for
more than sysenter now and keeping the name makes backtraces
confusing.
- Prevent LDT inheritance on exec() by moving it to arch_dup_mmap(),
which is only invoked on fork().
- Make vysycall more robust.
- A few fixes and cleanups of the debug_pagetables code. Check
PAGE_PRESENT instead of checking the PTE for 0 and a cleanup of the
C89 initialization of the address hint array which already was out
of sync with the index enums.
- Move the ESPFIX init to a different place to prepare for PTI.
- Several code moves with no functional change to make PTI
integration simpler and header files less convoluted.
- Documentation fixes and clarifications"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/cpu_entry_area: Prevent wraparound in setup_cpu_entry_area_ptes() on 32bit
init: Invoke init_espfix_bsp() from mm_init()
x86/cpu_entry_area: Move it out of the fixmap
x86/cpu_entry_area: Move it to a separate unit
x86/mm: Create asm/invpcid.h
x86/mm: Put MMU to hardware ASID translation in one place
x86/mm: Remove hard-coded ASID limit checks
x86/mm: Move the CR3 construction functions to tlbflush.h
x86/mm: Add comments to clarify which TLB-flush functions are supposed to flush what
x86/mm: Remove superfluous barriers
x86/mm: Use __flush_tlb_one() for kernel memory
x86/microcode: Dont abuse the TLB-flush interface
x86/uv: Use the right TLB-flush API
x86/entry: Rename SYSENTER_stack to CPU_ENTRY_AREA_entry_stack
x86/doc: Remove obvious weirdnesses from the x86 MM layout documentation
x86/mm/64: Improve the memory map documentation
x86/ldt: Prevent LDT inheritance on exec
x86/ldt: Rework locking
arch, mm: Allow arch_dup_mmap() to fail
x86/vsyscall/64: Warn and fail vsyscall emulation in NATIVE mode
...
Put the cpu_entry_area into a separate P4D entry. The fixmap gets too big
and 0-day already hit a case where the fixmap PTEs were cleared by
cleanup_highmap().
Aside of that the fixmap API is a pain as it's all backwards.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The old docs had the vsyscall range wrong and were missing the fixmap.
Fix both.
There used to be 8 MB reserved for future vsyscalls, but that's long gone.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that CPUs that implement Memory Protection Keys are publicly
available we can be a bit less oblique about where it is available.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20171111001228.DC748A10@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 cache resource updates from Thomas Gleixner:
"This update provides updates to RDT:
- A diagnostic framework for the Resource Director Technology (RDT)
user interface (sysfs). The failure modes of the user interface are
hard to diagnose from the error codes. An extra last command status
file provides now sensible textual information about the failure so
its simpler to use.
- A few minor cleanups and updates in the RDT code"
* 'x86-cache-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel_rdt: Fix a silent failure when writing zero value schemata
x86/intel_rdt: Fix potential deadlock during resctrl mount
x86/intel_rdt: Fix potential deadlock during resctrl unmount
x86/intel_rdt: Initialize bitmask of shareable resource if CDP enabled
x86/intel_rdt: Remove redundant assignment
x86/intel_rdt/cqm: Make integer rmid_limbo_count static
x86/intel_rdt: Add documentation for "info/last_cmd_status"
x86/intel_rdt: Add diagnostics when making directories
x86/intel_rdt: Add diagnostics when writing the cpus file
x86/intel_rdt: Add diagnostics when writing the tasks file
x86/intel_rdt: Add diagnostics when writing the schemata file
x86/intel_rdt: Add framework for better RDT UI diagnostics
We are going to support boot-time switching between 4- and 5-level
paging. For KASAN it means we cannot have different KASAN_SHADOW_OFFSET
for different paging modes: the constant is passed to gcc to generate
code and cannot be changed at runtime.
This patch changes KASAN code to use 0xdffffc0000000000 as shadow offset
for both 4- and 5-level paging.
For 5-level paging it means that shadow memory region is not aligned to
PGD boundary anymore and we have to handle unaligned parts of the region
properly.
In addition, we have to exclude paravirt code from KASAN instrumentation
as we now use set_pgd() before KASAN is fully ready.
[kirill.shutemov@linux.intel.com: clenaup, changelog message]
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@suse.de>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170929140821.37654-4-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Rename the unwinder config options from:
CONFIG_ORC_UNWINDER
CONFIG_FRAME_POINTER_UNWINDER
CONFIG_GUESS_UNWINDER
to:
CONFIG_UNWINDER_ORC
CONFIG_UNWINDER_FRAME_POINTER
CONFIG_UNWINDER_GUESS
... in order to give them a more logical config namespace.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/73972fc7e2762e91912c6b9584582703d6f1b8cc.1507924831.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
New file in the "info" directory helps diagnose what went wrong
when using the /sys/fs/resctrl file system
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vikas Shivappa <vikas.shivappa@intel.com>
Cc: Boris Petkov <bp@suse.de>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Link: https://lkml.kernel.org/r/387e78e444582403c2454479e576caf5721a363f.1506382469.git.tony.luck@intel.com
Pull x86 cache quality monitoring update from Thomas Gleixner:
"This update provides a complete rewrite of the Cache Quality
Monitoring (CQM) facility.
The existing CQM support was duct taped into perf with a lot of issues
and the attempts to fix those turned out to be incomplete and
horrible.
After lengthy discussions it was decided to integrate the CQM support
into the Resource Director Technology (RDT) facility, which is the
obvious choise as in hardware CQM is part of RDT. This allowed to add
Memory Bandwidth Monitoring support on top.
As a result the mechanisms for allocating cache/memory bandwidth and
the corresponding monitoring mechanisms are integrated into a single
management facility with a consistent user interface"
* 'x86-cache-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
x86/intel_rdt: Turn off most RDT features on Skylake
x86/intel_rdt: Add command line options for resource director technology
x86/intel_rdt: Move special case code for Haswell to a quirk function
x86/intel_rdt: Remove redundant ternary operator on return
x86/intel_rdt/cqm: Improve limbo list processing
x86/intel_rdt/mbm: Fix MBM overflow handler during CPU hotplug
x86/intel_rdt: Modify the intel_pqr_state for better performance
x86/intel_rdt/cqm: Clear the default RMID during hotcpu
x86/intel_rdt: Show bitmask of shareable resource with other executing units
x86/intel_rdt/mbm: Handle counter overflow
x86/intel_rdt/mbm: Add mbm counter initialization
x86/intel_rdt/mbm: Basic counting of MBM events (total and local)
x86/intel_rdt/cqm: Add CPU hotplug support
x86/intel_rdt/cqm: Add sched_in support
x86/intel_rdt: Introduce rdt_enable_key for scheduling
x86/intel_rdt/cqm: Add mount,umount support
x86/intel_rdt/cqm: Add rmdir support
x86/intel_rdt: Separate the ctrl bits from rmdir
x86/intel_rdt/cqm: Add mon_data
x86/intel_rdt: Prepare for RDT monitor data support
...
Pull x86 mm changes from Ingo Molnar:
"PCID support, 5-level paging support, Secure Memory Encryption support
The main changes in this cycle are support for three new, complex
hardware features of x86 CPUs:
- Add 5-level paging support, which is a new hardware feature on
upcoming Intel CPUs allowing up to 128 PB of virtual address space
and 4 PB of physical RAM space - a 512-fold increase over the old
limits. (Supercomputers of the future forecasting hurricanes on an
ever warming planet can certainly make good use of more RAM.)
Many of the necessary changes went upstream in previous cycles,
v4.14 is the first kernel that can enable 5-level paging.
This feature is activated via CONFIG_X86_5LEVEL=y - disabled by
default.
(By Kirill A. Shutemov)
- Add 'encrypted memory' support, which is a new hardware feature on
upcoming AMD CPUs ('Secure Memory Encryption', SME) allowing system
RAM to be encrypted and decrypted (mostly) transparently by the
CPU, with a little help from the kernel to transition to/from
encrypted RAM. Such RAM should be more secure against various
attacks like RAM access via the memory bus and should make the
radio signature of memory bus traffic harder to intercept (and
decrypt) as well.
This feature is activated via CONFIG_AMD_MEM_ENCRYPT=y - disabled
by default.
(By Tom Lendacky)
- Enable PCID optimized TLB flushing on newer Intel CPUs: PCID is a
hardware feature that attaches an address space tag to TLB entries
and thus allows to skip TLB flushing in many cases, even if we
switch mm's.
(By Andy Lutomirski)
All three of these features were in the works for a long time, and
it's coincidence of the three independent development paths that they
are all enabled in v4.14 at once"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (65 commits)
x86/mm: Enable RCU based page table freeing (CONFIG_HAVE_RCU_TABLE_FREE=y)
x86/mm: Use pr_cont() in dump_pagetable()
x86/mm: Fix SME encryption stack ptr handling
kvm/x86: Avoid clearing the C-bit in rsvd_bits()
x86/CPU: Align CR3 defines
x86/mm, mm/hwpoison: Clear PRESENT bit for kernel 1:1 mappings of poison pages
acpi, x86/mm: Remove encryption mask from ACPI page protection type
x86/mm, kexec: Fix memory corruption with SME on successive kexecs
x86/mm/pkeys: Fix typo in Documentation/x86/protection-keys.txt
x86/mm/dump_pagetables: Speed up page tables dump for CONFIG_KASAN=y
x86/mm: Implement PCID based optimization: try to preserve old TLB entries using PCID
x86: Enable 5-level paging support via CONFIG_X86_5LEVEL=y
x86/mm: Allow userspace have mappings above 47-bit
x86/mm: Prepare to expose larger address space to userspace
x86/mpx: Do not allow MPX if we have mappings above 47-bit
x86/mm: Rename tasksize_32bit/64bit to task_size_32bit/64bit()
x86/xen: Redefine XEN_ELFNOTE_INIT_P2M using PUD_SIZE * PTRS_PER_PUD
x86/mm/dump_pagetables: Fix printout of p4d level
x86/mm/dump_pagetables: Generalize address normalization
x86/boot: Fix memremap() related build failure
...
Pull x86 microcode loading updates from Ingo Molnar:
"Update documentation, improve robustness and fix a memory leak"
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode/intel: Improve microcode patches saving flow
x86/microcode: Document the three loading methods
x86/microcode/AMD: Free unneeded patch before exit from update_cache()
CPUID.(EAX=0x10, ECX=res#):EBX[31:0] reports a bit mask for a resource.
Each set bit within the length of the CBM indicates the corresponding
unit of the resource allocation may be used by other entities in the
platform (e.g. an integrated graphics engine or hardware units outside
the processor core and have direct access to the resource). Each
cleared bit within the length of the CBM indicates the corresponding
allocation unit can be configured to implement a priority-based
allocation scheme without interference with other hardware agents in
the system. Bits outside the length of the CBM are reserved.
More details on the bit mask are described in x86 Software Developer's
Manual.
The bitmask is shown in "info" directory for each resource. It's
up to user to decide how to use the bitmask within a CBM in a partition
to share or isolate a resource with other executing units.
Suggested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: ravi.v.shankar@intel.com
Cc: peterz@infradead.org
Cc: eranian@google.com
Cc: ak@linux.intel.com
Cc: davidcc@google.com
Cc: vikas.shivappa@linux.intel.com
Link: http://lkml.kernel.org/r/20170725223904.12996-1-tony.luck@intel.com
Add the new ORC unwinder which is enabled by CONFIG_ORC_UNWINDER=y.
It plugs into the existing x86 unwinder framework.
It relies on objtool to generate the needed .orc_unwind and
.orc_unwind_ip sections.
For more details on why ORC is used instead of DWARF, see
Documentation/x86/orc-unwinder.txt - but the short version is
that it's a simplified, fundamentally more robust debugninfo
data structure, which also allows up to two orders of magnitude
faster lookups than the DWARF unwinder - which matters to
profiling workloads like perf.
Thanks to Andy Lutomirski for the performance improvement ideas:
splitting the ORC unwind table into two parallel arrays and creating a
fast lookup table to search a subset of the unwind table.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/0a6cbfb40f8da99b7a45a1a8302dc6aef16ec812.1500938583.git.jpoimboe@redhat.com
[ Extended the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Replace PKEY_DENY_WRITE with PKEY_DISABLE_WRITE,
to match the source code.
Signed-off-by: Wang Kai <morgan.wang@huawei.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: corbet@lwn.net
Cc: dave.hansen@intel.com
Cc: dave.hansen@linux.intel.com
Cc: linux-doc@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Paul Menzel recently asked how to load microcode on a system and I realized
that we don't really have all the methods written down somewhere.
Do that, so people can go and look them up.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170724101228.17326-3-bp@alien8.de
[ Fix whitespace noise in the new description. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Most of things are in place and we can enable support for 5-level paging.
The patch makes XEN_PV and XEN_PVH dependent on !X86_5LEVEL. Both are
not ready to work with 5-level paging.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170716225954.74185-9-kirill.shutemov@linux.intel.com
[ Minor readability edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The bootlog option is only disabled by default on AMD Fam10h and older
systems.
Update bootlog description to say this. Change the family value to hex
to avoid confusion.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170613162835.30750-9-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 mm updates from Ingo Molnar:
"The main x86 MM changes in this cycle were:
- continued native kernel PCID support preparation patches to the TLB
flushing code (Andy Lutomirski)
- various fixes related to 32-bit compat syscall returning address
over 4Gb in applications, launched from 64-bit binaries - motivated
by C/R frameworks such as Virtuozzo. (Dmitry Safonov)
- continued Intel 5-level paging enablement: in particular the
conversion of x86 GUP to the generic GUP code. (Kirill A. Shutemov)
- x86/mpx ABI corner case fixes/enhancements (Joerg Roedel)
- ... plus misc updates, fixes and cleanups"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (62 commits)
mm, zone_device: Replace {get, put}_zone_device_page() with a single reference to fix pmem crash
x86/mm: Fix flush_tlb_page() on Xen
x86/mm: Make flush_tlb_mm_range() more predictable
x86/mm: Remove flush_tlb() and flush_tlb_current_task()
x86/vm86/32: Switch to flush_tlb_mm_range() in mark_screen_rdonly()
x86/mm/64: Fix crash in remove_pagetable()
Revert "x86/mm/gup: Switch GUP to the generic get_user_page_fast() implementation"
x86/boot/e820: Remove a redundant self assignment
x86/mm: Fix dump pagetables for 4 levels of page tables
x86/mpx, selftests: Only check bounds-vs-shadow when we keep shadow
x86/mpx: Correctly report do_mpx_bt_fault() failures to user-space
Revert "x86/mm/numa: Remove numa_nodemask_from_meminfo()"
x86/espfix: Add support for 5-level paging
x86/kasan: Extend KASAN to support 5-level paging
x86/mm: Add basic defines/helpers for CONFIG_X86_5LEVEL=y
x86/paravirt: Add 5-level support to the paravirt code
x86/mm: Define virtual memory map for 5-level paging
x86/asm: Remove __VIRTUAL_MASK_SHIFT==47 assert
x86/boot: Detect 5-level paging support
x86/mm/numa: Remove numa_nodemask_from_meminfo()
...
Pull x86 cpu updates from Ingo Molnar:
"The biggest changes are an extension of the Intel RDT code to extend
it with Intel Memory Bandwidth Allocation CPU support: MBA allows
bandwidth allocation between cores, while CBM (already upstream)
allows CPU cache partitioning.
There's also misc smaller fixes and updates"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/intel_rdt: Return error for incorrect resource names in schemata
x86/intel_rdt: Trim whitespace while parsing schemata input
x86/intel_rdt: Fix padding when resource is enabled via mount
x86/intel_rdt: Get rid of anon union
x86/cpu: Keep model defines sorted by model number
x86/intel_rdt/mba: Add schemata file support for MBA
x86/intel_rdt: Make schemata file parsers resource specific
x86/intel_rdt/mba: Add info directory files for Memory Bandwidth Allocation
x86/intel_rdt: Make information files resource specific
x86/intel_rdt/mba: Add primary support for Memory Bandwidth Allocation (MBA)
x86/intel_rdt/mba: Memory bandwith allocation feature detect
x86/intel_rdt: Add resource specific msr update function
x86/intel_rdt: Move CBM specific data into a struct
x86/intel_rdt: Cleanup namespace to support multiple resource types
Documentation, x86: Intel Memory bandwidth allocation
x86/intel_rdt: Organize code properly
x86/intel_rdt: Init padding only if a device exists
x86/intel_rdt: Add cpus_list rdtgroup file
x86/intel_rdt: Cleanup kernel-doc
x86/intel_rdt: Update schemata read to show data in tabular format
...
There's a conflict between ongoing level-5 paging support and
the E820 rewrite. Since the E820 rewrite is essentially ready,
merge it into x86/mm to reduce tree conflicts.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The resource control filesystem provides only a bitmask based cpus file for
assigning CPUs to a resource group. That's cumbersome with large cpumasks
and non-intuitive when modifying the file from the command line.
Range based cpu lists are commonly used along with bitmask based cpu files
in various subsystems throughout the kernel.
Add 'cpus_list' file which is CPU range based.
# cd /sys/fs/resctrl/
# echo 1-10 > krava/cpus_list
# cat krava/cpus_list
1-10
# cat krava/cpus
0007fe
# cat cpus
fffff9
# cat cpus_list
0,3-23
[ tglx: Massaged changelog and replaced "bitmask lists" by "CPU ranges" ]
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Shaohua Li <shli@fb.com>
Link: http://lkml.kernel.org/r/20170410145232.GF25354@krava
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The schemata file can have multiple lines and it is cumbersome to update
all lines.
Remove code that requires that the user provides values for every resource
(in the right order). If the user provides values for just a few
resources, update them and leave the rest unchanged.
Side benefit: we now check which values were updated and only send IPIs to
cpus that actually have updates.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Vikas Shivappa <vikas.shivappa@linux.intel.com>
Tested-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Cc: ravi.v.shankar@intel.com
Cc: fenghua.yu@intel.com
Cc: peterz@infradead.org
Cc: vikas.shivappa@intel.com
Cc: h.peter.anvin@intel.com
Link: http://lkml.kernel.org/r/1491255857-17213-3-git-send-email-vikas.shivappa@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The first part of memory map (up to %esp fixup) simply scales existing
map for 4-level paging by factor of 9 -- number of bits addressed by
the additional page table level.
The rest of the map is unchanged.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170330080731.65421-4-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch aligns MODULES_END to the beginning of the fixmap section.
It optimizes the space available for both sections. The address is
pre-computed based on the number of pages required by the fixmap
section.
It will allow GDT remapping in the fixmap section. The current
MODULES_END static address does not provide enough space for the kernel
to support a large number of processors.
Signed-off-by: Thomas Garnier <thgarnie@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Luis R . Rodriguez <mcgrof@kernel.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Rafael J . Wysocki <rjw@rjwysocki.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: kasan-dev@googlegroups.com
Cc: kernel-hardening@lists.openwall.com
Cc: kvm@vger.kernel.org
Cc: lguest@lists.ozlabs.org
Cc: linux-doc@vger.kernel.org
Cc: linux-efi@vger.kernel.org
Cc: linux-mm@kvack.org
Cc: linux-pm@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Cc: zijun_hu <zijun_hu@htc.com>
Link: http://lkml.kernel.org/r/20170314170508.100882-1-thgarnie@google.com
[ Small build fix. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 fixes from Ingo Molnar:
"Two documentation updates, plus a debugging annotation fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/crash: Update the stale comment in reserve_crashkernel()
x86/irq, trace: Add __irq_entry annotation to x86's platform IRQ handlers
Documentation, x86, resctrl: Recommend locking for resctrlfs
Get the firmware's secure-boot status in the kernel boot wrapper and stash
it somewhere that the main kernel image can find.
The efi_get_secureboot() function is extracted from the ARM stub and (a)
generalised so that it can be called from x86 and (b) made to use
efi_call_runtime() so that it can be run in mixed-mode.
For x86, it is stored in boot_params and can be overridden by the boot
loader or kexec. This allows secure-boot mode to be passed on to a new
kernel.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1486380166-31868-5-git-send-email-ard.biesheuvel@linaro.org
[ Small readability edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
No change in functionality.
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Jackson <pj@sgi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In line with the rename to 'struct e820_array', harmonize the naming of common e820
table variable names as well:
e820 => e820_array
e820_saved => e820_array_saved
e820_map => e820_array
initial_e820 => e820_array_init
This makes the variable names more consistent and easier to grep for.
No change in functionality.
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Jackson <pj@sgi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The 'e820entry' and 'e820map' names have various annoyances:
- the missing underscore departs from the usual kernel style
and makes the code look weird,
- in the past I kept confusing the 'map' with the 'entry', because
a 'map' is ambiguous in that regard,
- it's not really clear from the 'e820map' that this is a regular
C array.
Rename them to 'struct e820_entry' and 'struct e820_array' accordingly.
( Leave the legacy UAPI header alone but do the rename in the bootparam.h
and e820/types.h file - outside tools relying on these defines should
either adjust their code, or should use the legacy header, or should
create their private copies for the definitions. )
No change in functionality.
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Jackson <pj@sgi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 fixes from Ingo Molnar:
"There's a number of fixes:
- a round of fixes for CPUID-less legacy CPUs
- a number of microcode loader fixes
- i8042 detection robustization fixes
- stack dump/unwinder fixes
- x86 SoC platform driver fixes
- a GCC 7 warning fix
- virtualization related fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
Revert "x86/unwind: Detect bad stack return address"
x86/paravirt: Mark unused patch_default label
x86/microcode/AMD: Reload proper initrd start address
x86/platform/intel/quark: Add printf attribute to imr_self_test_result()
x86/platform/intel-mid: Switch MPU3050 driver to IIO
x86/alternatives: Do not use sync_core() to serialize I$
x86/topology: Document cpu_llc_id
x86/hyperv: Handle unknown NMIs on one CPU when unknown_nmi_panic
x86/asm: Rewrite sync_core() to use IRET-to-self
x86/microcode/intel: Replace sync_core() with native_cpuid()
Revert "x86/boot: Fail the boot if !M486 and CPUID is missing"
x86/asm/32: Make sync_core() handle missing CPUID on all 32-bit kernels
x86/cpu: Probe CPUID leaf 6 even when cpuid_level == 6
x86/tools: Fix gcc-7 warning in relocs.c
x86/unwind: Dump stack data on warnings
x86/unwind: Adjust last frame check for aligned function stacks
x86/init: Fix a couple of comment typos
x86/init: Remove i8042_detect() from platform ops
Input: i8042 - Trust firmware a bit more when probing on X86
x86/init: Add i8042 state to the platform data
...
Pull x86 cache allocation interface from Thomas Gleixner:
"This provides support for Intel's Cache Allocation Technology, a cache
partitioning mechanism.
The interface is odd, but the hardware interface of that CAT stuff is
odd as well.
We tried hard to come up with an abstraction, but that only allows
rather simple partitioning, but no way of sharing and dealing with the
per package nature of this mechanism.
In the end we decided to expose the allocation bitmaps directly so all
combinations of the hardware can be utilized.
There are two ways of associating a cache partition:
- Task
A task can be added to a resource group. It uses the cache
partition associated to the group.
- CPU
All tasks which are not member of a resource group use the group to
which the CPU they are running on is associated with.
That allows for simple CPU based partitioning schemes.
The main expected user sare:
- Virtualization so a VM can only trash only the associated part of
the cash w/o disturbing others
- Real-Time systems to seperate RT and general workloads.
- Latency sensitive enterprise workloads
- In theory this also can be used to protect against cache side
channel attacks"
[ Intel RDT is "Resource Director Technology". The interface really is
rather odd and very specific, which delayed this pull request while I
was thinking about it. The pull request itself came in early during
the merge window, I just delayed it until things had calmed down and I
had more time.
But people tell me they'll use this, and the good news is that it is
_so_ specific that it's rather independent of anything else, and no
user is going to depend on the interface since it's pretty rare. So if
push comes to shove, we can just remove the interface and nothing will
break ]
* 'x86-cache-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
x86/intel_rdt: Implement show_options() for resctrlfs
x86/intel_rdt: Call intel_rdt_sched_in() with preemption disabled
x86/intel_rdt: Update task closid immediately on CPU in rmdir and unmount
x86/intel_rdt: Fix setting of closid when adding CPUs to a group
x86/intel_rdt: Update percpu closid immeditately on CPUs affected by changee
x86/intel_rdt: Reset per cpu closids on unmount
x86/intel_rdt: Select KERNFS when enabling INTEL_RDT_A
x86/intel_rdt: Prevent deadlock against hotplug lock
x86/intel_rdt: Protect info directory from removal
x86/intel_rdt: Add info files to Documentation
x86/intel_rdt: Export the minimum number of set mask bits in sysfs
x86/intel_rdt: Propagate error in rdt_mount() properly
x86/intel_rdt: Add a missing #include
MAINTAINERS: Add maintainer for Intel RDT resource allocation
x86/intel_rdt: Add scheduler hook
x86/intel_rdt: Add schemata file
x86/intel_rdt: Add tasks files
x86/intel_rdt: Add cpus file
x86/intel_rdt: Add mkdir to resctrl file system
x86/intel_rdt: Add "info" files to resctrl file system
...
It means different things on Intel and AMD so write it down so that
there's no confusion.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Yazen Ghannam <yazen.ghannam@amd.com>
Link: http://lkml.kernel.org/r/20161117094557.jm6hwzdd52h7iwnj@pd.tnic
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
