In non secure mode, soc_pm.data.mode is set when entering pm in
at91_pm_begin(). This value is used (not only) to determine if the system
is going into slow clock mode (at91_suspend_entering_slow_clock()). This
function is called from various drivers to check this and act accordingly.
If not set, the driver might enter an incorrect suspend mode. When using
secure suspend mode, at91_pm_begin() is not called and thus
soc_pm.data.mode is not set. Since when using secure suspend, only one
suspend mode is supported, set this value directly in
at91_pm_secure_init().
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Thomas Perrot <thomas.perrot@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20231020130219.1255937-1-thomas.perrot@bootlin.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it was merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
A couple of other includes are unused and can be dropped too.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230717225429.3211307-1-robh@kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
The of_find_device_by_node() function is returning a struct platform_device
object with the embedded struct device member's reference counter
incremented. This needs to be dropped when done with the platform device
returned by of_find_device_by_node().
at91_pm_eth_quirk_is_valid() calls of_find_device_by_node() on
suspend and resume path. On suspend it calls of_find_device_by_node() and
on resume and failure paths it drops the counter of
struct platform_device::dev.
In case ethernet device may not wakeup there is a put_device() on
at91_pm_eth_quirk_is_valid() which is wrong as it colides with
put_device() on resume path leading to the reference counter of struct
device embedded in struct platform_device to be messed, stack trace to be
displayed (after 5 consecutive suspend/resume cycles) and execution to
hang.
Along with this the error path of at91_pm_config_quirks() had been also
adapted to decrement propertly the reference counter of struct device
embedded in struct platform_device.
Fixes: b7fc72c633 ("ARM: at91: pm: add quirks for pm")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20230518062511.2988500-1-claudiu.beznea@microchip.com
New drivers:
- Cypress CY8C95x0 chip pin control support, along with an immediate
cleanup.
- Mediatek MT8188 SoC pin control support.
- Qualcomm SM8450 and SC8280XP LPASS (low power audio subsystem)
pin control support.
- Qualcomm PM7250, PM8450
- Rockchip RV1126 SoC pin control support.
Improvements:
- Fix some missing pins in the Armada 37xx driver.
- Convert Broadcom and Nomadik drivers to use PINCTRL_PINGROUP() macro.
- Fix some GPIO irq_chips to be immutable.
- Massive Qualcomm device tree binding cleanup, with more to come.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAmNEhjMACgkQQRCzN7AZ
XXMNXRAAuqKM8b/Kw7H9S2sBgMuESk2WKe/lmJ6mQCWK1iyo0xecEQi1wN3WGZt1
DfoYHdsB45GWnRcwIVIl2wAjce72EFepCa/sut55TR/bLDxRfSiHGBKatSk5VkQp
IGx75EtsRPgnZCUU3jQgrQEiI8eqj90nr8CugZwD7gocjAtaRJXb0cc3NPyk/TDh
Wyku3rYuzztLCJHwsZ7Q9zh3s9b8Vb43pK9BW8HHeuODqMECaDWTEQUDetKz/Z8X
v7v01PSOafBQUCoFPezz/20kOV9llxFSCeCqbwG3zvjPSjofVwSFoSH1Op4Ybr/t
JWM8Py1+/G/rbsRhZuEahLJ+/eLy7SWABSUq2sxwCEr/VkzNCZ1jKH/qB1S7ZkI6
GcHPbEeCDzcN+yfKIo8p6WHUYivpj2XKXqh/BWIY63rJ3ukrq3WHuJNvCO15F/TJ
PDuLIL0RdNxSanoamsplNtFWA3ap92P2P933k+v06VEZpZys8j/JHFUaysbiqpL+
GoHdRjspFC/4Ob3FwbbiYktpoKmRsZl7PCJSYnnz5nrHFUbQ4LtrgppqMgGXny16
P0pW8IBmIF4yVteodQFsyYZq2yH91TengHleqoFsK0OjYXG0BmRm3lYWLjWbojxe
U7E5T5qQo2rtdVct9d47UznK3IRThDDJx9DtG+Y19VpkKiOy6j8=
=PvLX
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"There is nothing exciting going on, no core changes, just a few
drivers and cleanups.
New drivers:
- Cypress CY8C95x0 chip pin control support, along with an immediate
cleanup
- Mediatek MT8188 SoC pin control support
- Qualcomm SM8450 and SC8280XP LPASS (low power audio subsystem) pin
control support
- Qualcomm PM7250, PM8450
- Rockchip RV1126 SoC pin control support
Improvements:
- Fix some missing pins in the Armada 37xx driver
- Convert Broadcom and Nomadik drivers to use PINCTRL_PINGROUP()
macro
- Fix some GPIO irq_chips to be immutable
- Massive Qualcomm device tree binding cleanup, with more to come"
* tag 'pinctrl-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (119 commits)
MAINTAINERS: adjust STARFIVE JH7100 PINCTRL DRIVER after file movement
pinctrl: starfive: Rename "pinctrl-starfive" to "pinctrl-starfive-jh7100"
pinctrl: Create subdirectory for StarFive drivers
dt-bindings: pinctrl: st,stm32: Document interrupt-controller property
dt-bindings: pinctrl: st,stm32: Document gpio-hog pattern property
dt-bindings: pinctrl: st,stm32: Document gpio-line-names
pinctrl: st: stop abusing of_get_named_gpio()
pinctrl: wpcm450: Correct the fwnode_irq_get() return value check
pinctrl: bcm: Remove unused struct bcm6328_pingroup
pinctrl: qcom: restrict drivers per ARM/ARM64
pinctrl: bcm: ns: Remove redundant dev_err call
gpio: rockchip: request GPIO mux to pinctrl when setting direction
pinctrl: rockchip: add pinmux_ops.gpio_set_direction callback
pinctrl: cy8c95x0: Align function names in cy8c95x0_pmxops
pinctrl: cy8c95x0: Drop atomicity on operations on push_pull
pinctrl: cy8c95x0: Lock register accesses in cy8c95x0_set_mux()
pinctrl: sunxi: sun50i-h5: Switch to use dev_err_probe() helper
pinctrl: stm32: Switch to use dev_err_probe() helper
dt-bindings: qcom-pmic-gpio: Add PM7250B and PM8450 bindings
pinctrl: qcom: spmi-gpio: Add compatible for PM7250B
...
Move gpio suspend/resume execution local to driver and let it execute as
close as possible to the moment the machine specific PM code is executed
(by setting it to .noirq member of dev_pm_ops). With this the
at91_pinctrl_gpio_suspend()/at91_pinctrl_gpio_resume() calls were removed
from arch/arm/mach-at91/pm.c and also a header has been removed.
The patch has been checked on sama5d3_xplained, sam9x60ek,
sama5d2_xplained, sama7g5ek boards.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220831135636.3176406-3-claudiu.beznea@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On SAMA7G5, when resuming from backup and self-refresh, the bootloader
performs DDR PHY recalibration by restoring the value of ZQ0SR0 (stored
in RAM by Linux before going to backup and self-refresh). It has been
discovered that the current procedure doesn't work for all possible values
that might go to ZQ0SR0 due to hardware bug. The workaround to this is to
avoid storing some values in ZQ0SR0. Thus Linux will read the ZQ0SR0
register and cache its value in RAM after processing it (using
modified_gray_code array). The bootloader will restore the processed value.
Fixes: d2d4716d83 ("ARM: at91: pm: save ddr phy calibration data to securam")
Suggested-by: Frederic Schumacher <frederic.schumacher@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-4-claudiu.beznea@microchip.com
at91_pm_secure_init() is used inside sama5d2_pm_init(), which has
the __init notation.
Pass the __init notation to at91_pm_secure_init() as well to fix the
following section mismatch warning:
WARNING: modpost: vmlinux.o(.text.unlikely+0x2138): Section mismatch in reference from the function at91_pm_secure_init() to the (unknown reference) .init.rodata:(unknown)
Fixes: f2f5cf78a3 ("ARM: at91: pm: add support for sama5d2 secure suspend")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220622114810.1186330-1-festevam@gmail.com
When running with OP-TEE, the suspend control is handled securely.
Suspend can be entered using PSCI support. Since the sama5d2 supports
multiple suspend modes, add a new CONFIG_ATMEL_SECURE_PM which will
send a SMC call to select the suspend mode at init time.
"atmel.pm_modes" boot argument is still supported for compatibility
purposes but the standby value is actually ignored since PSCI suspend
is used and it only support one mode (suspend).
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
SoCs supporting ULP0 or ULP1 modes and variants of Cadence Ethernet IP
(controlled by macb driver) may behave buggy when Wake-on-Lan (WoL) is
configured and WoL packet is received while in ULP0/ULP1. On some SoCs
Ethernet interface is not working after resume. On other SoCs the CPU
goes to abort on resume path when switching execution from internal SRAM
to DRAM. For ULP1 + WoL the issue is related a particular restart
sequence of the internal clocks when resuming. These clocks are
automatically managed by PMC and may happen that GMAC peripheral clock
is restarted few clock cycles before internal clocks causing blocking
of Ethernet's DMA. As a consequence Ethernet TX transactions are stopped
and RX transactions are partially stopped (packets are received by MAC,
RX counters incremented but the data is not transferred to DRAM). The
workaround for this is to disable Ethernet's peripheral clock when
going to ULP1. Same behavior has been reproduced on ULP0 for some
platforms (SAMA5D2, SAMA5D3) and the same workaround solves the issue.
The problem has been solved on pm.c as quirk to avoid polluting the
MACB driver with AT91 specific issues as this driver is generic to
multiple vendors.
At probe pointers to struct device_node are retrieved and on the
at91_pm_enter() the quirk specifics are applied: for all Ethernet
interfaces that were parsed the peripheral clocks are disabled. A
special handling is done for modes in dns_modes mask as these are
considered modes that blocks the system if WoL packet are received
but for which applying quirk will lead to not waking up on WoL
packets: in situation where Ethernet interface(s) has suspend mode
in dns_modes mask and Ethernet interface(s) is the only available
wakeup source the suspend is canceled.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Use kernel documentation style. Along with it fix the naming of
struct at91_pm_sfrbu_regs in documentation.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Introduce macros to replace standby/suspend mode if they depends on
controllers that failed to map (or other errors). Macros keep track
of the complementary mode to avoid having set the same AT91 PM mode
for both suspend and standby.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Move documentation of bu to keep the same order as in the structure
itself.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Add CPU idle support for SAMA7G5. Support will make use of PMC_CPU_RATIO
register to divide the CPU clock by 16 before switching it to idle and
use automatic self-refresh option of DDR controller.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220113144900.906370-5-claudiu.beznea@microchip.com
Fix following coccicheck warning:
./arch/arm/mach-at91/pm.c:643:1-33: WARNING: Function
for_each_matching_node_and_match should have of_node_put() before goto
Early exits from for_each_matching_node_and_match should decrement the
node reference counter.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20211014084555.21422-1-wanjiabing@vivo.com
Backup area is now switched to VDDIN33 at boot (with the help of
bootloader). When switching to backup mode we need to switch backup area
to VBAT as all the other power sources are cut off. The resuming from
backup mode is done with the help of bootloader, so there is no need to
do something particular in Linux to restore backup area power source.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210830100927.22711-1-claudiu.beznea@microchip.com
In case PM is enabled but there is no RAM controller information
in DT the code will panic. Avoid such scenarios by not initializing
platform specific PM code in case RAM controller is not provided
via DT.
Reported-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixes: 827de1f123 ("ARM: at91: remove at91_dt_initialize and machine init_early()")
Fixes: 892e1f4a3a ("ARM: at91: pm: add sama7g5 ddr phy controller")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210823131915.23857-2-claudiu.beznea@microchip.com
Adapt at91_pm_backup_init() to work for SAMA7G5. Also, set the LPM pin
to shutdown controller. This will signal to PMIC that it needs to switch
to the state corresponding to backup mode.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-21-claudiu.beznea@microchip.com
The resuming from backup mode is done with the help of bootloader.
The bootloader reconfigure the DDR controller and DDR PHY controller.
To speed-up the resuming process save the PHY calibration data into
SECURAM before suspending (securam is powered on backup mode).
This data will be later used by bootloader in DDR PHY reconfiguration
process. Also, in the process or recalibration the first 8 words of
the memory may get corrupted. To solve this, these 8 words are saved
in the securam and restored by bootloader in the process of PHY
configuration.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-20-claudiu.beznea@microchip.com
SAMA7G5 self-refresh procedure accesses also the DDR PHY registers.
Adapt the code so that the at91_dt_ramc() to look also for DDR PHYs,
in case it is mandatory.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-19-claudiu.beznea@microchip.com
Add SAMA7G5 DDR controller to the list of DDR controller compatibles.
At the moment there is no standby support. Adapt the code for this.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-18-claudiu.beznea@microchip.com
at91_pm_modes_init() checks for proper nodes in device tree and maps
them accordingly. Up to SAMA7G5 all AT91 SoCs had the same mapping
b/w power saving modes and different controllers needed in the
final/first steps of suspend/resume. SAMA7G5 is not aligned with the
old SoCs thus the code is adapted for this. This patch prepares
the field for next commits.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-5-claudiu.beznea@microchip.com
Move the setup of soc_pm.bu->suspended in platform_suspend::begin
function so that the PMC code in charge with clocks suspend/resume
to differentiate b/w standard PM mode and backup mode.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-3-claudiu.beznea@microchip.com
Both the caller and the supplier's source file should have access to
the include file containing the prototypes.
Fixes the following W=1 kernel build warning(s):
drivers/pinctrl/pinctrl-at91.c:1637:6: warning: no previous prototype for ‘at91_pinctrl_gpio_suspend’ [-Wmissing-prototypes]
1637 | void at91_pinctrl_gpio_suspend(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/pinctrl-at91.c:1661:6: warning: no previous prototype for ‘at91_pinctrl_gpio_resume’ [-Wmissing-prototypes]
1661 | void at91_pinctrl_gpio_resume(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~
Cc: Russell King <linux@armlinux.org.uk>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210303124149.3149511-1-lee.jones@linaro.org
Not all SoCs supports all the PM mode. User may end up settings,
e.g. backup mode, on a non SAMA5D2 device, but the mode to not be valid.
If backup mode is used on a devices not supporting it there will be no
way of resuming other than rebooting.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1596616610-15460-3-git-send-email-claudiu.beznea@microchip.com
ULP0 fast improves suspend/resume time with few milliseconds the drawback
being the power consumption. The mean values measured for suspend/resume
time are as follows (measured on SAMA5D2 Xplained board), ULP0 compared
with fast ULP0:
- ulp0 fast: suspend time: 169 ms, resume time: 216 ms
- ulp0 : suspend time: 197 ms, resume time: 258 ms
Current consumption while suspended (measured on SAMA5D2 Xplained board):
- ulp0 fast: 730uA
- ulp0 : 270uA
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1596616610-15460-2-git-send-email-claudiu.beznea@microchip.com
if of_find_device_by_node() succeed, at91_pm_sram_init() doesn't have
a corresponding put_device(). Thus add a jump target to fix the exception
handling for this function implementation.
Fixes: d2e4679055 ("ARM: at91: pm: use the mmio-sram pool to access SRAM")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200604123301.3905837-1-yukuai3@huawei.com
This will be used to differentiate b/w different PLLs settings to be
applied in the final/first steps of the suspend/resume process by doing
PLL specific configurations.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1579522208-19523-5-git-send-email-claudiu.beznea@microchip.com
SAM9X60's PMC has different master clock register offset than the other
SoCs' PMC. Due to this, specify master clock register offset based
on PMC compatible and pass it to pm_suspend.S since it is also needed
in there. When PM part for SAM9X60 was published the SAM9X60's PMC
(commit f6deae46039c ("clk: at91: add sam9x60 pmc driver")) wasn't
integrated.
Fixes: 01c7031cfa ("ARM: at91: pm: initial PM support for SAM9X60")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1579522208-19523-2-git-send-email-claudiu.beznea@microchip.com
Use of_device_id array to find the proper shdwc compatibile node.
SAM9X60's shdwc changes were not integrated when
commit eaedc0d379 ("ARM: at91: pm: add ULP1 support for SAM9X60")
was integrated.
Fixes: eaedc0d379 ("ARM: at91: pm: add ULP1 support for SAM9X60")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1576062248-18514-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
SAM9X60 PMC's has a different PMC. It was not integrated at the moment
commit 01c7031cfa ("ARM: at91: pm: initial PM support for SAM9X60")
was published.
Fixes: 01c7031cfa ("ARM: at91: pm: initial PM support for SAM9X60")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1576062248-18514-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Move SAM9X60's PM part under SoC config flag. This allows the building
of SAM9X60 platform withouth depending on CONFIG_SOC_AT91SAM9 flag,
allowing us to select only necessary config flags for SAM9X60.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1575035505-6310-4-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
- fix a pm.c warning with W=1
-----BEGIN PGP SIGNATURE-----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=XBOT
-----END PGP SIGNATURE-----
Merge tag 'at91-5.3-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/soc
AT91 SoC for 5.3
- fix a pm.c warning with W=1
* tag 'at91-5.3-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
arm: add missing include platform-data/atmel.h
Signed-off-by: Olof Johansson <olof@lixom.net>
Include corresponding headerfile <linux/platform-data/atmel.h> for
function at91_suspend_entering_slow_clock().
../arch/arm/mach-at91/pm.c:279:5: warning: no previous prototype for ‘at91_suspend_entering_slow_clock’ [-Wmissing-prototypes]
int at91_suspend_entering_slow_clock(void)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Philippe Mazenauer <philippe.mazenauer@outlook.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_find_device_by_node() takes a reference to the struct device
when it finds a match via get_device. When returning error we should
call put_device.
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Peng Hao <peng.hao2@zte.com.cn>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Add ULP1 support for SAM9X60. In pm_suspend.S enable RC oscillator in
PMC if it is not enabled. At resume the state before suspend is
restored.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Add support for per SoC wakeup source configuration. In this way
we could have per SoC wakeup sources, shutdown controller and power
management controller configurations for ULP1 power management mode.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
In at91_pm_backup_init() return if it is not about SAMA5D2 SoCs.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
