Pull networking updates from David Miller:
1) BBR TCP congestion control, from Neal Cardwell, Yuchung Cheng and
co. at Google. https://lwn.net/Articles/701165/
2) Do TCP Small Queues for retransmits, from Eric Dumazet.
3) Support collect_md mode for all IPV4 and IPV6 tunnels, from Alexei
Starovoitov.
4) Allow cls_flower to classify packets in ip tunnels, from Amir Vadai.
5) Support DSA tagging in older mv88e6xxx switches, from Andrew Lunn.
6) Support GMAC protocol in iwlwifi mwm, from Ayala Beker.
7) Support ndo_poll_controller in mlx5, from Calvin Owens.
8) Move VRF processing to an output hook and allow l3mdev to be
loopback, from David Ahern.
9) Support SOCK_DESTROY for UDP sockets. Also from David Ahern.
10) Congestion control in RXRPC, from David Howells.
11) Support geneve RX offload in ixgbe, from Emil Tantilov.
12) When hitting pressure for new incoming TCP data SKBs, perform a
partial rathern than a full purge of the OFO queue (which could be
huge). From Eric Dumazet.
13) Convert XFRM state and policy lookups to RCU, from Florian Westphal.
14) Support RX network flow classification to igb, from Gangfeng Huang.
15) Hardware offloading of eBPF in nfp driver, from Jakub Kicinski.
16) New skbmod packet action, from Jamal Hadi Salim.
17) Remove some inefficiencies in snmp proc output, from Jia He.
18) Add FIB notifications to properly propagate route changes to
hardware which is doing forwarding offloading. From Jiri Pirko.
19) New dsa driver for qca8xxx chips, from John Crispin.
20) Implement RFC7559 ipv6 router solicitation backoff, from Maciej
Żenczykowski.
21) Add L3 mode to ipvlan, from Mahesh Bandewar.
22) Support 802.1ad in mlx4, from Moshe Shemesh.
23) Support hardware LRO in mediatek driver, from Nelson Chang.
24) Add TC offloading to mlx5, from Or Gerlitz.
25) Convert various drivers to ethtool ksettings interfaces, from
Philippe Reynes.
26) TX max rate limiting for cxgb4, from Rahul Lakkireddy.
27) NAPI support for ath10k, from Rajkumar Manoharan.
28) Support XDP in mlx5, from Rana Shahout and Saeed Mahameed.
29) UDP replicast support in TIPC, from Richard Alpe.
30) Per-queue statistics for qed driver, from Sudarsana Reddy Kalluru.
31) Support BQL in thunderx driver, from Sunil Goutham.
32) TSO support in alx driver, from Tobias Regnery.
33) Add stream parser engine and use it in kcm.
34) Support async DHCP replies in ipconfig module, from Uwe
Kleine-König.
35) DSA port fast aging for mv88e6xxx driver, from Vivien Didelot.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1715 commits)
mlxsw: switchx2: Fix misuse of hard_header_len
mlxsw: spectrum: Fix misuse of hard_header_len
net/faraday: Stop NCSI device on shutdown
net/ncsi: Introduce ncsi_stop_dev()
net/ncsi: Rework the channel monitoring
net/ncsi: Allow to extend NCSI request properties
net/ncsi: Rework request index allocation
net/ncsi: Don't probe on the reserved channel ID (0x1f)
net/ncsi: Introduce NCSI_RESERVED_CHANNEL
net/ncsi: Avoid unused-value build warning from ia64-linux-gcc
net: Add netdev all_adj_list refcnt propagation to fix panic
net: phy: Add Edge-rate driver for Microsemi PHYs.
vmxnet3: Wake queue from reset work
i40e: avoid NULL pointer dereference and recursive errors on early PCI error
qed: Add RoCE ll2 & GSI support
qed: Add support for memory registeration verbs
qed: Add support for QP verbs
qed: PD,PKEY and CQ verb support
qed: Add support for RoCE hw init
qede: Add qedr framework
...
There is no need to clk_disable_unprepare(dev->clk)
before it was initialized.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 2 warnings when building kernel with W=1:
drivers/net/ethernet/marvell/mvneta.c:639:27: warning: no previous prototype for 'mvneta_get_stats64' [-Wmissing-prototypes]
drivers/net/ethernet/marvell/mvneta.c:3529:5: warning: no previous prototype for 'mvneta_ethtool_set_link_ksettings' [-Wmissing-prototypes]
In fact, these two functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: netdev@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160818125731.27256-9-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Update the sky2 driver to pass number of packets done to NAPI.
The driver was never updated when napi_complete_done was added.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the mvneta driver to new api {get|set}_link_ksettings.
We use the generic function phy_ethtool_get_link_ksettings,
and update old mvneta_ethtool_set_settings to the new api.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy_dev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit aebea2ba0f ("net: mvneta: fix Tx interrupt delay") intended to
set coalescing threshold to a value guaranteeing interrupt generation
per each sent packet, so that buffers can be released with no delay.
In fact setting threshold to '1' was wrong, because it causes interrupt
every two packets. According to the documentation a reason behind it is
following - interrupt occurs once sent buffers counter reaches a value,
which is higher than one specified in MVNETA_TXQ_SIZE_REG(q). This
behavior was confirmed during tests. Also when testing the SoC working
as a NAS device, better performance was observed with int-per-packet,
as it strongly depends on the fact that all transmitted packets are
released immediately.
This commit enables NETA controller work in interrupt per sent packet mode
by setting coalescing threshold to 0.
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v3.10+
Fixes aebea2ba0f ("net: mvneta: fix Tx interrupt delay")
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en.h
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
drivers/net/usb/r8152.c
All three conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock used by the hwbm functions must be initialized by the
network driver. This commit fixes this lack and the following erros when
lockdep is enabled:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
[<c010ff80>] (unwind_backtrace) from [<c010bd08>] (show_stack+0x10/0x14)
[<c010bd08>] (show_stack) from [<c032913c>] (dump_stack+0xb4/0xe0)
[<c032913c>] (dump_stack) from [<c01670e4>] (__lock_acquire+0x1f58/0x2060)
[<c01670e4>] (__lock_acquire) from [<c0167dec>] (lock_acquire+0xa4/0xd0)
[<c0167dec>] (lock_acquire) from [<c06f6650>] (_raw_spin_lock_irqsave+0x54/0x68)
[<c06f6650>] (_raw_spin_lock_irqsave) from [<c058e830>] (hwbm_pool_add+0x1c/0xdc)
[<c058e830>] (hwbm_pool_add) from [<c043f4e8>] (mvneta_bm_pool_use+0x338/0x490)
[<c043f4e8>] (mvneta_bm_pool_use) from [<c0443198>] (mvneta_probe+0x654/0x1284)
[<c0443198>] (mvneta_probe) from [<c03b894c>] (platform_drv_probe+0x4c/0xb0)
[<c03b894c>] (platform_drv_probe) from [<c03b7158>] (driver_probe_device+0x214/0x2c0)
[<c03b7158>] (driver_probe_device) from [<c03b72c4>] (__driver_attach+0xc0/0xc4)
[<c03b72c4>] (__driver_attach) from [<c03b5440>] (bus_for_each_dev+0x68/0x9c)
[<c03b5440>] (bus_for_each_dev) from [<c03b65b8>] (bus_add_driver+0x1a0/0x218)
[<c03b65b8>] (bus_add_driver) from [<c03b79cc>] (driver_register+0x78/0xf8)
[<c03b79cc>] (driver_register) from [<c01018f4>] (do_one_initcall+0x90/0x1dc)
[<c01018f4>] (do_one_initcall) from [<c0900de4>] (kernel_init_freeable+0x15c/0x1fc)
[<c0900de4>] (kernel_init_freeable) from [<c06eed90>] (kernel_init+0x8/0x114)
[<c06eed90>] (kernel_init) from [<c0107910>] (ret_from_fork+0x14/0x24)
Fixes: baa11ebc0c ("net: mvneta: Use the new hwbm framework")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the pxa168_eth driver to use the dma_rmb/wmb calls instead of the
full barriers in order to improve performance: reduced 97ns/39ns on
average in tx/rx path on Marvell BG4CT platform.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since appropriate memory barriers are already there, use the relaxed
version to improve performance a bit.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
I tried to fix this before, but my previous fix was incomplete
and we can still get the same link error in randconfig builds
because of the way that Kconfig treats the
default y if MVNETA=y && MVNETA_BM_ENABLE
line that does not actually trigger when MVNETA_BM_ENABLE=m,
unlike I intended.
Changing the line to use MVNETA_BM_ENABLE!=n however has
the desired effect and hopefully makes all configurations
work as expected.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 019ded3aa7 ("net: mvneta: bm: clarify dependencies")
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mdiobus_scan() doesn't return NULL on failure anymore, this driver
no longer needs to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3b9d6da67e ("cpu/hotplug: Fix rollback during error-out
in __cpu_disable()") it is ensured that callbacks of CPU_ONLINE and
CPU_DOWN_PREPARE are processed on the hotplugged CPU. Due to this SMP
function calls are no longer required.
Replace smp_call_function_single() with a direct call to
mvneta_percpu_enable() or mvneta_percpu_disable(). The functions do
not require to be called with interrupts disabled, therefore the
smp_call_function_single() calling convention is not preserved.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mdiobus_scan() returns either an error code or NULL on error, the
driver should check for both, not only for NULL, otherwise a crash is
imminent...
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After enabling per-cpu processing it appeared that under heavy load
changing MTU can result in blocking all port's interrupts and
transmitting data is not possible after the change.
This commit fixes above issue by disabling percpu interrupts for the
time, when TXQs and RXQs are reconfigured.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L1_CACHE_BYTES may not be the real cacheline size, use cache_line_size
to determine the cacheline size in runtime.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Suggested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L1_CACHE_BYTES may not be the real cacheline size, use cache_line_size
to determine the cacheline size in runtime.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Suggested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to fix the following maybe-uninitialized warning:
drivers/net/ethernet/marvell/mvpp2.c:6007:18: warning: 'err' may be
used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta is also used in some Marvell berlin family SoCs which may
have 64bytes cacheline size. Replace the MVNETA_CPU_D_CACHE_LINE_SIZE
usage with L1_CACHE_BYTES.
And since dma_alloc_coherent() is always cacheline size aligned, so
remove the align checks.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2 ip maybe used in SoCs which may have have 64bytes cacheline
size. Replace the MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES.
And since dma_alloc_coherent() is always cacheline size aligned, so
remove the align checks.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MVNETA_BM has a dependency on MVNETA, so we can only select the former
if the latter is enabled. However, the code dependency is the reverse:
The mvneta module can call into the mvneta_bm module, so mvneta cannot
be a built-in if mvneta_bm is a module, or we get a link error:
drivers/net/built-in.o: In function `mvneta_remove':
drivers/net/ethernet/marvell/mvneta.c:4211: undefined reference to `mvneta_bm_pool_destroy'
drivers/net/built-in.o: In function `mvneta_bm_update_mtu':
drivers/net/ethernet/marvell/mvneta.c:1034: undefined reference to `mvneta_bm_bufs_free'
This avoids the problem by further clarifying the dependency so that
MVNETA_BM is a silent Kconfig option that gets turned on by the
new MVNETA_BM_ENABLE option. This way both the core HWBM module and
the MVNETA_BM code are always built-in when needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: dc35a10f68 ("net: mvneta: bm: add support for hardware buffer management")
Signed-off-by: David S. Miller <davem@davemloft.net>
Some literal values are actually already defined by macros, so let's use
them.
[gregory.clement@free-electrons.com: split intial commit in two
individual changes]
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit corrects error printing when shutting down the port.
[gregory.clement@free-electrons.com: split initial commit in two
individual changes]
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function eth_prepare_mac_addr_change() is called as part of MAC
address change. This function check if interface is running.
To enable change MAC address when interface is running:
IFF_LIVE_ADDR_CHANGE flag must be set to dev->priv_flags field
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP
network unit")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous patch, the spinlock was not initialized. While it didn't
cause any trouble yet it could be a problem to use it uninitialized.
The most annoying part was the critical section protected by the spinlock
in mvneta_stop(). Some of the functions could sleep as pointed when
activated CONFIG_DEBUG_ATOMIC_SLEEP. Actually, in mvneta_stop() we only
need to protect the is_stopped flagged, indeed the code of the notifier
for CPU online is protected by the same spinlock, so when we get the
lock, the notifer work is done.
Reported-by: Patrick Uiterwijk <patrick@puiterwijk.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta_percpu_notifier() hotplug callback lacks handling of the
CPU_DOWN_FAILED case. That means, if CPU_DOWN_PREPARE failes, the
driver is not well configured on the CPU.
Add handling for CPU_DOWN_FAILED[_FROZEN] hotplug notifier transition
to setup the driver.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the hardware buffer management framework had been introduced,
let's use it.
Tested-by: Sebastian Careba <nitroshift@yahoo.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Buffer manager (BM) is a dedicated hardware unit that can be used by all
ethernet ports of Armada XP and 38x SoC's. It allows to offload CPU on RX
path by sparing DRAM access on refilling buffer pool, hardware-based
filling of descriptor ring data and better memory utilization due to HW
arbitration for using 'short' pools for small packets.
Tests performed with A388 SoC working as a network bridge between two
packet generators showed increase of maximum processed 64B packets by
~20k (~555k packets with BM enabled vs ~535 packets without BM). Also
when pushing 1500B-packets with a line rate achieved, CPU load decreased
from around 25% without BM to 20% with BM.
BM comprise up to 4 buffer pointers' (BP) rings kept in DRAM, which
are called external BP pools - BPPE. Allocating and releasing buffer
pointers (BP) to/from BPPE is performed indirectly by write/read access
to a dedicated internal SRAM, where internal BP pools (BPPI) are placed.
BM hardware controls status of BPPE automatically, as well as assigning
proper buffers to RX descriptors. For more details please refer to
Functional Specification of Armada XP or 38x SoC.
In order to enable support for a separate hardware block, common for all
ports, a new driver has to be implemented ('mvneta_bm'). It provides
initialization sequence of address space, clocks, registers, SRAM,
empty pools' structures and also obtaining optional configuration
from DT (please refer to device tree binding documentation). mvneta_bm
exposes also a necessary API to mvneta driver, as well as a dedicated
structure with BM information (bm_priv), whose presence is used as a
flag notifying of BM usage by port. It has to be ensured that mvneta_bm
probe is executed prior to the ones in ports' driver. In case BM is not
used or its probe fails, mvneta falls back to use software buffer
management.
A sequence executed in mvneta_probe function is modified in order to have
an access to needed resources before possible port's BM initialization is
done. According to port-pools mapping provided by DT appropriate registers
are configured and the buffer pools are filled. RX path is modified
accordingly. Becaues the hardware allows a wide variety of configuration
options, following assumptions are made:
* using BM mechanisms can be selectively disabled/enabled basing
on DT configuration among the ports
* 'long' pool's single buffer size is tied to port's MTU
* using 'long' pool by port is obligatory and it cannot be shared
* using 'short' pool for smaller packets is optional
* one 'short' pool can be shared among all ports
This commit enables hardware buffer management operation cooperating with
existing mvneta driver. New device tree binding documentation is added and
the one of mvneta is updated accordingly.
[gregory.clement@free-electrons.com: removed the suspend/resume part]
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When stopping the port, the CPU notifier are still there whereas the
mvneta_stop_dev function calls mvneta_percpu_disable() on each CPUs.
It was possible to have a new CPU coming at this point which could be
racy.
This patch adds a flag preventing executing the code notifier for a new
CPU when the port is stopping. It also uses the spinlock introduces
previously. To avoid the deadlock, the lock has been moved outside the
mvneta_percpu_elect function.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Electing a CPU must be done in an atomic way: it should be done after or
before the removal/insertion of a CPU and this function is not reentrant.
During the loop of mvneta_percpu_elect we associates the queues to the
CPUs, if there is a topology change during this loop, then the mapping
between the CPUs and the queues could be wrong. During this loop the
interrupt mask is also updating for each CPUs, It should not be changed
in the same time by other part of the driver.
This patch adds spinlock to create the needed critical sections.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the MVNETA_INTR_* registers, the queues related fields are per cpu,
according to the datasheet (comment in [] are added by me):
"In a multi-CPU system, bits of RX[or TX] queues for which the access by
the reading[or writing] CPU is disabled are read as 0, and cannot be
cleared[or written]."
That means that each time we want to manipulate these bits we had to do
it on each cpu and not only on the current cpu.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the commit 2dcf75e279 ("net: mvneta: Associate RX queues with
each CPU") all the percpu irq are used and disabled at initialization, so
there is no point to disable them first.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a for_each_* loop in which we just call the
smp_call_function_single macro, it is more simple to directly use the
on_each_cpu macro. Moreover, this macro ensures that the calls will be
done all at once.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When passing to the management of multiple RX queue, the
mvneta_percpu_elect function was broken. The use of the modulo can lead
to elect the wrong cpu. For example with rxq_def=2, if the CPU 2 goes
offline and then online, we ended with the third RX queue activated in
the same time on CPU 0 and CPU2, which lead to a kernel crash.
With this fix, we don't try to get "the closer" CPU if the default CPU is
gone, now we just use CPU 0 which always be there. Thanks to this, the
code becomes more readable, easier to maintain and more predicable.
Cc: stable@vger.kernel.org
Fixes: 2dcf75e279 ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch convert the for_each_present in on_each_cpu, instead of
applying on the present cpus it will be applied only on the online cpus.
This fix a bug reported on
http://thread.gmane.org/gmane.linux.ports.arm.kernel/468173.
Using the macro on_each_cpu (instead of a for_each_* loop) also ensures
that all the calls will be done all at once.
Fixes: f864288544 ("net: mvneta: Statically assign queues to CPUs")
Reported-by: Stefan Roese <stefan.roese@gmail.com>
Suggested-by: Jisheng Zhang <jszhang@marvell.com>
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of kzalloc on failure of allocation of memory should
be -ENOMEM and not -1.
Found using Coccinelle. A simplified version of the semantic patch
used is:
//<smpl>
@@
expression *e;
position p,q;
@@
e@q = kzalloc(...);
if@p (e == NULL) {
...
return
- -1
+ -ENOMEM
;
}
//</smpl>
This function may also return -1 after calling mpp2_prs_tcam_port_map_get.
So that the function consistently returns meaningful error values on
failure, the -1 is changed to -EINVAL.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
