When the gadget driver hasn't been (yet) configured, and the cable is
connected to a HOST, the SFTDISCON gets cleared unconditionally, so the
HOST tries to enumerate it.
At the host side, this can result in a stuck USB port or worse. When
getting lucky, some dmesg can be observed at the host side:
new high-speed USB device number ...
device descriptor read/64, error -110
Fix it in drd, by checking the enabled flag before calling
dwc2_hsotg_core_connect(). It will be called later, once configured,
by the normal flow:
- udc_bind_to_driver
- usb_gadget_connect
- dwc2_hsotg_pullup
- dwc2_hsotg_core_connect
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1644999135-13478-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the Bay Trail phy GPIO mappings where added cs and reset were swapped,
this did not cause any issues sofar, because sofar they were always driven
high/low at the same time.
Note the new mapping has been verified both in /sys/kernel/debug/gpio
output on Android factory images on multiple devices, as well as in
the schematics for some devices.
Fixes: 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt mask is enabled before any potential failure points in
the driver, which can leave a failure path where we exit with
interrupts enabled but the device not live. This causes an infinite
stream of interrupts on an Apple M1 Pro laptop on USB-C.
Add a failure label that's used post enabling interrupts, where we
mask them again before returning an error.
Suggested-by: Sven Peter <sven@svenpeter.dev>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/e6b80669-20f3-06e7-9ed5-8951a9c6db6f@kernel.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The -ENODEV return value from xhci_check_args() is incorrectly changed
to -EINVAL in a couple places before propagated further.
xhci_check_args() returns 4 types of value, -ENODEV, -EINVAL, 1 and 0.
xhci_urb_enqueue and xhci_check_streams_endpoint return -EINVAL if
the return value of xhci_check_args <= 0.
This causes problems for example r8152_submit_rx, calling usb_submit_urb
in drivers/net/usb/r8152.c.
r8152_submit_rx will never get -ENODEV after submiting an urb when xHC
is halted because xhci_urb_enqueue returns -EINVAL in the very beginning.
[commit message and header edit -Mathias]
Fixes: 203a86613f ("xhci: Avoid NULL pointer deref when host dies.")
Cc: stable@vger.kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When HCE(Host Controller Error) is set, it means an internal
error condition has been detected. Software needs to re-initialize
the HC, so add this check in xhci resume.
Cc: stable@vger.kernel.org
Signed-off-by: Puma Hsu <pumahsu@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e0082698b6 ("usb: dwc3: ulpi: conditionally resume ULPI PHY")
fixed an issue where ULPI transfers would timeout if any requests where
send to the phy sometime after init, giving it enough time to auto-suspend.
Commit e5f4ca3fce ("usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend
regression") changed the behavior to instead of clearing the
DWC3_GUSB2PHYCFG_SUSPHY bit, add an extra sleep when it is set.
But on Bay Trail devices, when phy_set_mode() gets called during init,
this leads to errors like these:
[ 28.451522] tusb1210 dwc3.ulpi: error -110 writing val 0x01 to reg 0x0a
[ 28.464089] tusb1210 dwc3.ulpi: error -110 writing val 0x01 to reg 0x0a
Add "snps,dis_u2_susphy_quirk" to the settings for Bay Trail devices to
fix this. This restores the old behavior for Bay Trail devices, since
previously the DWC3_GUSB2PHYCFG_SUSPHY bit would get cleared on the first
ulpi_read/_write() and then was never set again.
Fixes: e5f4ca3fce ("usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend regression")
Cc: stable@kernel.org
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids for 5.17-rc4.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYgZ+2gAKCRALxc3C7H1l
CDoSAP9qPhQUn/i4I6ggD4oB25VaGWHxZVaoQYj/R74OjvWxDwEA0+5fIbS9T8qr
rU70IRzH4KDdW3OFPCgr58+MIotAtwc=
=1R+F
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.17-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.17-rc4
Here are some new device ids for 5.17-rc4.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.17-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cp210x: add CPI Bulk Coin Recycler id
USB: serial: cp210x: add NCR Retail IO box id
USB: serial: ftdi_sio: add support for Brainboxes US-159/235/320
USB: serial: option: add ZTE MF286D modem
USB: serial: ch341: add support for GW Instek USB2.0-Serial devices
When the gadget driver hasn't been (yet) configured, and the cable is
connected to a HOST, the SFTDISCON gets cleared unconditionally, so the
HOST tries to enumerate it.
At the host side, this can result in a stuck USB port or worse. When
getting lucky, some dmesg can be observed at the host side:
new high-speed USB device number ...
device descriptor read/64, error -110
Fix it in drd, by checking the enabled flag before calling
dwc2_hsotg_core_connect(). It will be called later, once configured,
by the normal flow:
- udc_bind_to_driver
- usb_gadget_connect
- dwc2_hsotg_pullup
- dwc2_hsotg_core_connect
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Cc: stable@kernel.org
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1644423353-17859-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the size of the RNDIS_MSG_SET command given to us before
attempting to respond to an invalid message size.
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Cc: stable@kernel.org
Tested-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stall the control endpoint in case provided index exceeds array size of
MAX_CONFIG_INTERFACES or when the retrieved function pointer is null.
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8c67d06f3f ("usb: Link the ports to the connectors they are
attached to") creates a link to the USB Type-C connector for every new
port that is added when possible. If component_add() fails,
usb_hub_create_port_device() prints a warning but does not unregister
the device and does not return errors to the callers.
Syzbot reported a "WARNING in component_del()".
Fix this issue in usb_hub_create_port_device by calling device_unregister()
and returning the errors from component_add().
Fixes: 8c67d06f3f ("usb: Link the ports to the connectors they are attached to")
Reported-and-tested-by: syzbot+60df062e1c41940cae0f@syzkaller.appspotmail.com
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Link: https://lore.kernel.org/r/20220209164500.8769-1-fmdefrancesco@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With CPU re-ordering on write instructions, there might
be a chance that the HWO is set before the TRB is updated
with the new mapped buffer address.
And in the case where core is processing a list of TRBs
it is possible that it fetched the TRBs when the HWO is set
but before the buffer address is updated.
Prevent this by adding a memory barrier before the HWO
is updated to ensure that the core always process the
updated TRBs.
Fixes: f6bafc6a1c ("usb: dwc3: convert TRBs into bitshifts")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/1644207958-18287-1-git-send-email-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the Brainboxes US-159, US-235 and US-320
USB-to-Serial devices.
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Several users have reported that their Win10 does not enumerate UAC2
gadget with the existing wTerminalType set to
UAC_INPUT_TERMINAL_UNDEFINED/UAC_INPUT_TERMINAL_UNDEFINED, e.g.
https://github.com/raspberrypi/linux/issues/4587#issuecomment-926567213.
While the constant is officially defined by the USB terminal types
document, e.g. XMOS firmware for UAC2 (commonly used for Win10) defines
no undefined output terminal type in its usbaudio20.h header.
Therefore wTerminalType of EP-IN is set to
UAC_INPUT_TERMINAL_MICROPHONE and wTerminalType of EP-OUT to
UAC_OUTPUT_TERMINAL_SPEAKER for the UAC2 gadget.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220131071813.7433-1-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The support the external role switch a variety of situations were
addressed, but the transition from USB_ROLE_HOST to USB_ROLE_NONE
leaves the host up which can cause some error messages when
switching from host to none, to gadget, to none, and then back
to host again.
xhci-hcd ee000000.usb: Abort failed to stop command ring: -110
xhci-hcd ee000000.usb: xHCI host controller not responding, assume dead
xhci-hcd ee000000.usb: HC died; cleaning up
usb 4-1: device not accepting address 6, error -108
usb usb4-port1: couldn't allocate usb_device
After this happens it will not act as a host again.
Fix this by releasing the host mode when transitioning to USB_ROLE_NONE.
Fixes: 0604160d8c ("usb: gadget: udc: renesas_usb3: Enhance role switch support")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20220128223603.2362621-1-aford173@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under dummy_hcd, every available endpoint is *either* IN or OUT capable.
But with some real hardware, there are endpoints that support both IN and
OUT. In particular, the PLX 2380 has four available endpoints that each
support both IN and OUT.
raw-gadget currently gets confused and thinks that any endpoint that is
usable as an IN endpoint can never be used as an OUT endpoint.
Fix it by looking at the direction in the configured endpoint descriptor
instead of looking at the hardware capabilities.
With this change, I can use the PLX 2380 with raw-gadget.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Cc: stable <stable@vger.kernel.org>
Tested-by: Andrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20220126205214.2149936-1-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for boost-up register of usb251xb hub.
boost-up property control USB electrical drive strength
This register can be set:
- Normal mode -> 0x00
- Low -> 0x01
- Medium -> 0x10
- High -> 0x11
(Normal Default)
References:
- http://www.mouser.com/catalog/specsheets/2514.pdf p29
Reviewed-by: Richard Leitner <richard.leitner@linux.dev>
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
Link: https://lore.kernel.org/r/20220128181713.96856-1-tomm.merciai@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_node_put should always be called on device nodes gotten from
of_get_*. Additionally, it should only be called after there are no
remaining users. To address the first issue, call of_node_put if later
steps in ulpi_register fail. To address the latter, call put_device if
device_register fails, which will call ulpi_dev_release if necessary.
Fixes: ef6a7bcfb0 ("usb: ulpi: Support device discovery via DT")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20220127190004.1446909-3-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers are not unbound from the device when ulpi_unregister_interface
is called. Move of_node-freeing code to ulpi_dev_release which is called
only after all users are gone.
Fixes: ef6a7bcfb0 ("usb: ulpi: Support device discovery via DT")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20220127190004.1446909-2-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Programmable lab power supplies made by GW Instek, such as the
GPP-2323, have a USB port exposing a serial port to control the device.
Stringing the supplied Windows driver, references to the ch341 chip are
found. Binding the existing ch341 driver to the VID/PID of the GPP-2323
("GW Instek USB2.0-Serial" as per the USB product name) works out of the
box, communication and control is now possible.
This patch should work with any GPP series power supply due to
similarities in the product line.
Signed-off-by: Stephan Brunner <s.brunner@stephan-brunner.net>
Link: https://lore.kernel.org/r/4a47b864-0816-6f6a-efee-aa20e74bcdc6@stephan-brunner.net
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Consider a case where ffs_func_eps_disable is called from
ffs_func_disable as part of composition switch and at the
same time ffs_epfile_release get called from userspace.
ffs_epfile_release will free up the read buffer and call
ffs_data_closed which in turn destroys ffs->epfiles and
mark it as NULL. While this was happening the driver has
already initialized the local epfile in ffs_func_eps_disable
which is now freed and waiting to acquire the spinlock. Once
spinlock is acquired the driver proceeds with the stale value
of epfile and tries to free the already freed read buffer
causing use-after-free.
Following is the illustration of the race:
CPU1 CPU2
ffs_func_eps_disable
epfiles (local copy)
ffs_epfile_release
ffs_data_closed
if (last file closed)
ffs_data_reset
ffs_data_clear
ffs_epfiles_destroy
spin_lock
dereference epfiles
Fix this races by taking epfiles local copy & assigning it under
spinlock and if epfiles(local) is null then update it in ffs->epfiles
then finally destroy it.
Extending the scope further from the race, protecting the ep related
structures, and concurrent accesses.
Fixes: a9e6f83c2d ("usb: gadget: f_fs: stop sleeping in ffs_func_eps_disable")
Co-developed-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Pratham Pratap <quic_ppratap@quicinc.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/1643256595-10797-1-git-send-email-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A previous patch to skip part of the initialization when a USB3 PHY was
not present could result in the return value being uninitialized in that
case, causing spurious probe failures. Initialize ret to 0 to avoid this.
Fixes: 9678f3361a ("usb: dwc3: xilinx: Skip resets and USB3 register settings for USB2.0 mode")
Cc: <stable@vger.kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220127221500.177021-1-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CDNSP driver read not initialized cdns->otg_v0_regs
which lead to segmentation fault. Patch fixes this issue.
Fixes: 2cf2581cd2 ("usb: cdns3: add power lost support for system resume")
cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220111090737.10345-1-pawell@gli-login.cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling dwc2_hsotg_ep_disable on ep0 (in/out) will lead to the following
logs before returning -EINVAL:
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
To avoid these two logs while suspending, start disabling the endpoint
from the index 1, as done in dwc2_hsotg_udc_stop:
/* all endpoints should be shutdown */
for (ep = 1; ep < hsotg->num_of_eps; ep++) {
if (hsotg->eps_in[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_in[ep]->ep);
if (hsotg->eps_out[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_out[ep]->ep);
}
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207130101.270314-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a build error observed with ARCH=arm DEFCONFIG=allmodconfig build.
drivers/usb/gadget/udc/at91_udc.h:174:42: error: format '%d' expects argument of type 'int', but argument 3 has type 'struct gpio_desc *' [-Werror=format=]
Fixes: 4a555f2b8d ("usb: gadget: at91_udc: Convert to GPIO descriptors")
Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220119020849.25732-1-miles.chen@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code that looked up the USB3 PHY was ignoring all errors other than
EPROBE_DEFER in an attempt to handle the PHY not being present. Fix and
simplify the code by using devm_phy_optional_get and dev_err_probe so
that a missing PHY is not treated as an error and unexpected errors
are handled properly.
Fixes: 84770f028f ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-3-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that the PIPE clock should not be selected when only USB 2.0
is being used in the design and no USB 3.0 reference clock is used.
Also, the core resets are not required if a USB3 PHY is not in use, and
will break things if USB3 is actually used but the PHY entry is not
listed in the device tree.
Skip core resets and register settings that are only required for
USB3 mode when no USB3 PHY is specified in the device tree.
Fixes: 84770f028f ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-2-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7495af9308 ("ARM: multi_v7_defconfig: Enable drivers for
DragonBoard 410c") enables the CONFIG_PHY_QCOM_USB_HS for the ARM
multi_v7_defconfig. Enabling this Kconfig is causing the kernel to crash
on the Tegra20 Ventana platform in the ulpi_match() function.
The Qualcomm USB HS PHY driver that is enabled by CONFIG_PHY_QCOM_USB_HS,
registers a ulpi_driver but this driver does not provide an 'id_table',
so when ulpi_match() is called on the Tegra20 Ventana platform, it
crashes when attempting to deference the id_table pointer which is not
valid. The Qualcomm USB HS PHY driver uses device-tree for matching the
ULPI driver with the device and so fix this crash by using device-tree
for matching if the id_table is not valid.
Fixes: ef6a7bcfb0 ("usb: ulpi: Support device discovery via DT")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20220117150039.44058-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently when gadget enumerates in super speed plus, the isoc
endpoint request buffer size is not calculated correctly. Fix
this by checking the gadget speed against USB_SPEED_SUPER_PLUS
and update the request buffer size.
Fixes: 90c4d05780 ("usb: fix various gadgets null ptr deref on 10gbps cabling.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Link: https://lore.kernel.org/r/1642820602-20619-1-git-send-email-quic_pkondeti@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CCGx clears Bit 0:Device Interrupt in the INTR_REG
if CCGx is reset successfully. However, there might
be a chance that other bits in INTR_REG are not
cleared due to internal data queued in PPM. This case
misleads the driver that CCGx reset failed.
The commit checks bit 0 in INTR_REG and ignores other
bits. The ucsi driver would reset PPM later.
Fixes: 247c554a14 ("usb: typec: ucsi: add support for Cypress CCGx")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20220112094143.628610-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzer has identified a bug in which processes hang waiting
for usb_kill_urb() to return. It turns out the issue is not unlinking
the URB; that works just fine. Rather, the problem arises when the
wakeup notification that the URB has completed is not received.
The reason is memory-access ordering on SMP systems. In outline form,
usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on
different CPUs perform the following actions:
CPU 0 CPU 1
---------------------------- ---------------------------------
usb_kill_urb(): __usb_hcd_giveback_urb():
... ...
atomic_inc(&urb->reject); atomic_dec(&urb->use_count);
... ...
wait_event(usb_kill_urb_queue,
atomic_read(&urb->use_count) == 0);
if (atomic_read(&urb->reject))
wake_up(&usb_kill_urb_queue);
Confining your attention to urb->reject and urb->use_count, you can
see that the overall pattern of accesses on CPU 0 is:
write urb->reject, then read urb->use_count;
whereas the overall pattern of accesses on CPU 1 is:
write urb->use_count, then read urb->reject.
This pattern is referred to in memory-model circles as SB (for "Store
Buffering"), and it is well known that without suitable enforcement of
the desired order of accesses -- in the form of memory barriers -- it
is entirely possible for one or both CPUs to execute their reads ahead
of their writes. The end result will be that sometimes CPU 0 sees the
old un-decremented value of urb->use_count while CPU 1 sees the old
un-incremented value of urb->reject. Consequently CPU 0 ends up on
the wait queue and never gets woken up, leading to the observed hang
in usb_kill_urb().
The same pattern of accesses occurs in usb_poison_urb() and the
failure pathway of usb_hcd_submit_urb().
The problem is fixed by adding suitable memory barriers. To provide
proper memory-access ordering in the SB pattern, a full barrier is
required on both CPUs. The atomic_inc() and atomic_dec() accesses
themselves don't provide any memory ordering, but since they are
present, we can use the optimized smp_mb__after_atomic() memory
barrier in the various routines to obtain the desired effect.
This patch adds the necessary memory barriers.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+76629376e06e2c2ad626@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8K0QYee0Q0Nna2@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two people have reported (and mentioned numerous other reports on the
web) that VIA's VL817 USB-SATA bridge does not work with the uas
driver. Typical log messages are:
[ 3606.232149] sd 14:0:0:0: [sdg] tag#2 uas_zap_pending 0 uas-tag 1 inflight: CMD
[ 3606.232154] sd 14:0:0:0: [sdg] tag#2 CDB: Write(16) 8a 00 00 00 00 00 18 0c c9 80 00 00 00 80 00 00
[ 3606.306257] usb 4-4.4: reset SuperSpeed Plus Gen 2x1 USB device number 11 using xhci_hcd
[ 3606.328584] scsi host14: uas_eh_device_reset_handler success
Surprisingly, the devices do seem to work okay for some other people.
The cause of the differing behaviors is not known.
In the hope of getting the devices to work for the most users, even at
the possible cost of degraded performance for some, this patch adds an
unusual_devs entry for the VL817 to block it from binding to the uas
driver by default. Users will be able to override this entry by means
of a module parameter, if they want.
CC: <stable@vger.kernel.org>
Reported-by: DocMAX <mail@vacharakis.de>
Reported-and-tested-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8IsK2sjlEv1rqU@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V causing VSAFE0V to be triggered. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED state where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid VSAFE0V events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
[23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected]
[23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[23.300579] VBUS off
[23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS]
[23.301014] VBUS VSAFE0V
[23.301111] Start toggling
Fixes: 28b43d3d74 ("usb: typec: tcpm: Introduce vsafe0v for vbus")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220122015520.332507-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V before tcpm gets to read port->tcpc->get_vbus. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid vbus off events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
[23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected]
[23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[23.300579] VBUS off
[23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS]
[23.301014] VBUS VSAFE0V
[23.301111] Start toggling
Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220122015520.332507-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes NULL pointer dereference that happens if
component master is registered with empty component match
list.
Fixes: 730b49aac4 ("usb: typec: port-mapper: Convert to the component framework")
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220124090228.41396-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code that creates the links to the USB ports attached to
a connector inside the system assumed that the ACPI nodes
(fwnodes) always exist for the connectors, but it can not do
that.
There is no guarantee that every USB Type-C connector has
ACPI device node representing it in the ACPI tables, and
even if there are the nodes in the ACPI tables, the _STA
method in those nodes may still return 0 (which means the
device does not exist from ACPI PoW).
This fixes NULL pointer dereference that happens if the
nodes are missing.
Fixes: 730b49aac4 ("usb: typec: port-mapper: Convert to the component framework")
Reported-and-tested-by: Robert Święcki <robert@swiecki.net>
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220124090228.41396-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the AMS and Collision Avoidance, tcpm often needs to change the CC's
termination. When one CC line is sourcing Vconn, if we still change its
termination, the voltage of the another CC line is likely to be fluctuant
and unstable.
Therefore, we should verify whether a CC line is sourcing Vconn before
changing its termination and only change the termination that is not
a Vconn line. This can be done by reading the Vconn Present bit of
POWER_ STATUS register. To determine the polarity, we can read the
Plug Orientation bit of TCPC_CONTROL register. Since Vconn can only be
sourced if Plug Orientation is set.
Fixes: 0908c5aca3 ("usb: typec: tcpm: AMS and Collision Avoidance")
cc: <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20220113092943.752372-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove PDE_DATA() completely and replace it with pde_data().
[akpm@linux-foundation.org: fix naming clash in drivers/nubus/proc.c]
[akpm@linux-foundation.org: now fix it properly]
Link: https://lkml.kernel.org/r/20211124081956.87711-2-songmuchun@bytedance.com
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alexey Gladkov <gladkov.alexey@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull signal/exit/ptrace updates from Eric Biederman:
"This set of changes deletes some dead code, makes a lot of cleanups
which hopefully make the code easier to follow, and fixes bugs found
along the way.
The end-game which I have not yet reached yet is for fatal signals
that generate coredumps to be short-circuit deliverable from
complete_signal, for force_siginfo_to_task not to require changing
userspace configured signal delivery state, and for the ptrace stops
to always happen in locations where we can guarantee on all
architectures that the all of the registers are saved and available on
the stack.
Removal of profile_task_ext, profile_munmap, and profile_handoff_task
are the big successes for dead code removal this round.
A bunch of small bug fixes are included, as most of the issues
reported were small enough that they would not affect bisection so I
simply added the fixes and did not fold the fixes into the changes
they were fixing.
There was a bug that broke coredumps piped to systemd-coredump. I
dropped the change that caused that bug and replaced it entirely with
something much more restrained. Unfortunately that required some
rebasing.
Some successes after this set of changes: There are few enough calls
to do_exit to audit in a reasonable amount of time. The lifetime of
struct kthread now matches the lifetime of struct task, and the
pointer to struct kthread is no longer stored in set_child_tid. The
flag SIGNAL_GROUP_COREDUMP is removed. The field group_exit_task is
removed. Issues where task->exit_code was examined with
signal->group_exit_code should been examined were fixed.
There are several loosely related changes included because I am
cleaning up and if I don't include them they will probably get lost.
The original postings of these changes can be found at:
https://lkml.kernel.org/r/87a6ha4zsd.fsf@email.froward.int.ebiederm.orghttps://lkml.kernel.org/r/87bl1kunjj.fsf@email.froward.int.ebiederm.orghttps://lkml.kernel.org/r/87r19opkx1.fsf_-_@email.froward.int.ebiederm.org
I trimmed back the last set of changes to only the obviously correct
once. Simply because there was less time for review than I had hoped"
* 'signal-for-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (44 commits)
ptrace/m68k: Stop open coding ptrace_report_syscall
ptrace: Remove unused regs argument from ptrace_report_syscall
ptrace: Remove second setting of PT_SEIZED in ptrace_attach
taskstats: Cleanup the use of task->exit_code
exit: Use the correct exit_code in /proc/<pid>/stat
exit: Fix the exit_code for wait_task_zombie
exit: Coredumps reach do_group_exit
exit: Remove profile_handoff_task
exit: Remove profile_task_exit & profile_munmap
signal: clean up kernel-doc comments
signal: Remove the helper signal_group_exit
signal: Rename group_exit_task group_exec_task
coredump: Stop setting signal->group_exit_task
signal: Remove SIGNAL_GROUP_COREDUMP
signal: During coredumps set SIGNAL_GROUP_EXIT in zap_process
signal: Make coredump handling explicit in complete_signal
signal: Have prepare_signal detect coredumps using signal->core_state
signal: Have the oom killer detect coredumps using signal->core_state
exit: Move force_uaccess back into do_exit
exit: Guarantee make_task_dead leaks the tsk when calling do_task_exit
...
Here is the big set of USB and Thunderbolt driver changes for 5.17-rc1.
Nothing major in here, just lots of little updates and cleanups. These
include:
- some USB header fixes picked from Ingo's header-splitup work
- more USB4/Thunderbolt hardware support added
- USB gadget driver updates and additions
- USB typec additions (includes some acpi changes, which were
acked by the ACPI maintainer)
- core USB fixes as found by syzbot that were too late for
5.16-final
- USB dwc3 driver updates
- USB dwc2 driver updates
- platform_get_irq() conversions of some USB drivers
- other minor USB driver updates and additions
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYd66Tg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynH2wCfetT95966ZMICGDmdwZpEBBYCO1wAn2v9Pwd2
CeXrMLdaOr9WkV2P6mE5
=K4Jh
-----END PGP SIGNATURE-----
Merge tag 'usb-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for
5.17-rc1.
Nothing major in here, just lots of little updates and cleanups. These
include:
- some USB header fixes picked from Ingo's header-splitup work
- more USB4/Thunderbolt hardware support added
- USB gadget driver updates and additions
- USB typec additions (includes some acpi changes, which were acked
by the ACPI maintainer)
- core USB fixes as found by syzbot that were too late for 5.16-final
- USB dwc3 driver updates
- USB dwc2 driver updates
- platform_get_irq() conversions of some USB drivers
- other minor USB driver updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (111 commits)
docs: ABI: fixed formatting in configfs-usb-gadget-uac2
usb: gadget: u_audio: Subdevice 0 for capture ctls
usb: gadget: u_audio: fix calculations for small bInterval
usb: dwc2: gadget: initialize max_speed from params
usb: dwc2: do not gate off the hardware if it does not support clock gating
usb: dwc3: qcom: Fix NULL vs IS_ERR checking in dwc3_qcom_probe
headers/deps: USB: Optimize <linux/usb/ch9.h> dependencies, remove <linux/device.h>
USB: common: debug: add needed kernel.h include
headers/prep: Fix non-standard header section: drivers/usb/host/ohci-tmio.c
headers/prep: Fix non-standard header section: drivers/usb/cdns3/core.h
headers/prep: usb: gadget: Fix namespace collision
USB: core: Fix bug in resuming hub's handling of wakeup requests
USB: Fix "slab-out-of-bounds Write" bug in usb_hcd_poll_rh_status
usb: dwc3: dwc3-qcom: Add missing platform_device_put() in dwc3_qcom_acpi_register_core
usb: gadget: clear related members when goto fail
usb: gadget: don't release an existing dev->buf
usb: dwc2: Simplify a bitmap declaration
usb: Remove usb_for_each_port()
usb: typec: port-mapper: Convert to the component framework
usb: Link the ports to the connectors they are attached to
...
Here is the big set of tty/serial driver updates for 5.17-rc1.
Nothing major in here, just lots of good updates and fixes, including:
- more tty core cleanups from Jiri as well as mxser driver
cleanups. This is the majority of the core diffstat
- tty documentation updates from Jiri
- platform_get_irq() updates
- various serial driver updates for new features and hardware
- fifo usage for 8250 console, reducing cpu load a lot
- LED fix for keyboards, long-time bugfix that went through many
revisions
- minor cleanups
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYd7Q0g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn3FACgoFZEFY04TU+Cd9mrlRq/mazZm/IAniJfPxOF
U0s57L5o1dlnmawh8mmV
=HSOB
-----END PGP SIGNATURE-----
Merge tag 'tty-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty/serial driver updates for 5.17-rc1.
Nothing major in here, just lots of good updates and fixes, including:
- more tty core cleanups from Jiri as well as mxser driver cleanups.
This is the majority of the core diffstat
- tty documentation updates from Jiri
- platform_get_irq() updates
- various serial driver updates for new features and hardware
- fifo usage for 8250 console, reducing cpu load a lot
- LED fix for keyboards, long-time bugfix that went through many
revisions
- minor cleanups
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
serial: core: Keep mctrl register state and cached copy in sync
serial: stm32: correct loop for dma error handling
serial: stm32: fix flow control transfer in DMA mode
serial: stm32: rework TX DMA state condition
serial: stm32: move tx dma terminate DMA to shutdown
serial: pl011: Drop redundant DTR/RTS preservation on close/open
serial: pl011: Drop CR register reset on set_termios
serial: pl010: Drop CR register reset on set_termios
serial: liteuart: fix MODULE_ALIAS
serial: 8250_bcm7271: Fix return error code in case of dma_alloc_coherent() failure
Revert "serdev: BREAK/FRAME/PARITY/OVERRUN notification prototype V2"
tty: goldfish: Use platform_get_irq() to get the interrupt
serdev: BREAK/FRAME/PARITY/OVERRUN notification prototype V2
tty: serial: meson: Drop the legacy compatible strings and clock code
serial: pmac_zilog: Use platform_get_irq() to get the interrupt
serial: bcm63xx: Use platform_get_irq() to get the interrupt
serial: ar933x: Use platform_get_irq() to get the interrupt
serial: vt8500: Use platform_get_irq() to get the interrupt
serial: altera_jtaguart: Use platform_get_irq_optional() to get the interrupt
serial: pxa: Use platform_get_irq() to get the interrupt
...
There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU,
as well as a new USIv2 driver that handles various types of
serial communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple
drivers, as well as memory controller support for RZ/G2L
(R9A07G044).
- Apple M1 gains support for the PMGR power management driver
-----BEGIN PGP SIGNATURE-----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=tlZT
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU, as
well as a new USIv2 driver that handles various types of serial
communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple drivers,
as well as memory controller support for RZ/G2L (R9A07G044).
- Apple M1 gains support for the PMGR power management driver"
* tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
soc: qcom: rpmh-rsc: Fix typo in a comment
soc: qcom: socinfo: Add SM6350 and SM7225
dt-bindings: arm: msm: Don't mark LLCC interrupt as required
dt-bindings: firmware: scm: Add SM6350 compatible
dt-bindings: arm: msm: Add LLCC for SM6350
soc: qcom: rpmhpd: Sort power-domain definitions and lists
soc: qcom: rpmhpd: Remove mx/cx relationship on sc7280
soc: qcom: rpmhpd: Rename rpmhpd struct names
soc: qcom: rpmhpd: sm8450: Add the missing .peer for sm8450_cx_ao
soc: qcom: socinfo: add SM8450 ID
soc: qcom: rpmhpd: Add SM8450 power domains
dt-bindings: power: rpmpd: Add SM8450 to rpmpd binding
soc: qcom: smem: Update max processor count
dt-bindings: arm: qcom: Document SM8450 SoC and boards
dt-bindings: firmware: scm: Add SM8450 compatible
dt-bindings: arm: cpus: Add kryo780 compatible
soc: qcom: rpmpd: Add support for sm6125
dt-bindings: qcom-rpmpd: Add sm6125 power domains
soc: qcom: aoss: constify static struct thermal_cooling_device_ops
PM: AVS: qcom-cpr: Use div64_ul instead of do_div
...
Both capture and playback alsa devices use subdevice 0. Yet capture-side
ctls are defined for subdevice 1. The patch sets subdevice 0 for them.
Fixes: 02de698ca8 ("usb: gadget: u_audio: add bi-directional volume and mute support")
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/20220105104643.90125-1-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
