This flag is a bit of a hack and the same thing can be accomplished
using a custom ->get_irq_reg() callback. Add a warning to catch any
use of the flag.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-13-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the internal sub_irq_reg() function with a public callback
that drivers can use when they have more complex register layouts.
The default implementation is regmap_irq_get_irq_reg_linear(), used
if the chip doesn't provide its own callback.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-12-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To me "unmask" suggests that we write 1s to the register when
an interrupt is enabled. This also makes sense because it's the
opposite of what the "mask" register does (write 1s to disable
an interrupt).
But regmap-irq does the opposite: for a disabled interrupt, it
writes 1s to "unmask" and 0s to "mask". This is surprising and
deviates from the usual way mask registers are handled.
Additionally, mask_invert didn't interact with unmask registers
properly -- it caused them to be ignored entirely.
Fix this by making mask and unmask registers orthogonal, using
the following behavior:
* Mask registers are written with 1s for disabled interrupts.
* Unmask registers are written with 1s for enabled interrupts.
This behavior supports both normal or inverted mask registers
and separate set/clear registers via different combinations of
mask_base/unmask_base.
The old unmask register behavior is deprecated. Drivers need to
opt-in to the new behavior by setting mask_unmask_non_inverted.
Warnings are issued if the driver relies on deprecated behavior.
Chips that only set one of mask_base/unmask_base don't have to
use the mask_unmask_non_inverted flag because that use case was
previously not supported.
The mask_invert flag is also deprecated in favor of describing
inverted mask registers as unmask registers.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-11-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Config registers can be used to replace both type and virtual
registers, so mark both features are deprecated and issue a
warning if they're used.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-10-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Config registers provide a more uniform approach to handling irq type
registers. They are essentially an extension of the virtual registers
used by the qcom-pm8008 driver.
Config registers can be represented as a 2D array:
config_base[0] reg0,0 reg0,1 reg0,2 reg0,3
config_base[1] reg1,0 reg1,1 reg1,2 reg1,3
config_base[2] reg2,0 reg2,1 reg2,2 reg2,3
There are 'num_config_bases' base registers, each of which is used to
address 'num_config_regs' registers. The addresses are calculated in
the same way as for other bases. It is assumed that an irq's type is
controlled by one column of registers; that column is identified by
the irq's 'type_reg_offset'.
The set_type_config() callback is responsible for updating the config
register contents. It receives an array of buffers (each represents a
row of registers) and the index of the column to update, along with
the 'struct regmap_irq' description and requested irq type.
Buffered values are written to registers in regmap_irq_sync_unlock().
Note that the entire register contents are overwritten, which is a
minor change in behavior from type registers via 'type_base'.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-9-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a71411dbf6 ("regmap: irq: add chip option mask_writeonly")
introduced the mask_writeonly option, but it isn't used now and it
appears it's never been used by any in-tree drivers. The motivation
for the option is mentioned in the commit message,
Some irq controllers have writeonly/multipurpose register
layouts. In those cases we read invalid data back. [...]
The option causes mask register updates to use regmap_write_bits()
instead of regmap_update_bits().
However, regmap_write_bits() doesn't solve the reading invalid data
problem. It's still a read-modify-write op like regmap_update_bits().
The difference is that 'update bits' will only write the new value
if it is different from the current value, while 'write bits' will
write the new value unconditionally, even if it's the same as the
current value.
This seems like a bit of a specialized use case and probably isn't
that useful for regmap-irq, so let's just remove the option and go
back to using an 'update bits' op for the mask registers. We can
always add the option back if some driver ends up needing it in the
future.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-7-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Check types_supported instead of checking type_rising/falling_val
when using type_in_mask interrupts. This makes the intent clearer
and allows a type_in_mask irq to support level or edge triggers,
rather than only edge triggers.
Update the documentation and comments to reflect the new behavior.
This shouldn't affect existing drivers, because if they didn't
set types_supported properly the type buffer wouldn't be updated.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-5-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It appears that no chip ever required a nonzero type_reg_stride
and commit 1066cfbdfa ("regmap-irq: Extend sub-irq to support
non-fixed reg strides") broke support. Just remove the field.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-3-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We have set/clear/test operations for regmap, but not for regmap_field yet.
So let's introduce regmap_field helpers too.
In many instances regmap_field_update_bits() is used for simple bit setting
and clearing. In these cases the last argument is redundant and we can
hide it with a static inline function.
This adds three new helpers for simple bit operations: set_bits,
clear_bits and test_bits (the last one defined as a regular function).
Signed-off-by: Li Chen <lchen@ambarella.com>
Link: https://lore.kernel.org/r/180eef422c3.deae9cd960729.8518395646822099769@zohomail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the regmap_config structure only allows the user to implement
single element register read/write using .reg_read/.reg_write callbacks.
The regmap_bus already implements bulk counterparts of both, and is being
misused as a workaround for the missing bulk read/write callbacks in
regmap_config by a couple of drivers. To stop this misuse, add the bulk
read/write callbacks to regmap_config and call them from the regmap core
code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Link: https://lore.kernel.org/r/20220430025145.640305-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
There's an inconsistency that arises when a register set can be accessed
internally via MMIO, or externally via SPI. The VSC7514 chip allows both
modes of operation. When internally accessed, the system utilizes __iomem,
devm_ioremap_resource, and devm_regmap_init_mmio.
For SPI it isn't possible to utilize memory-mapped IO. To properly operate,
the resource base must be added to the register before every operation.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20220313224524.399947-3-colin.foster@in-advantage.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an additional reg_downshift to be applied to register addresses before
any register accesses. An example of a device that uses this is a VSC7514
chip, which require each register address to be downshifted by two if the
access is performed over a SPI bus.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20220313224524.399947-2-colin.foster@in-advantage.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some device requires a special handling for reg_update_bits and can't use
the normal regmap read write logic. An example is when locking is
handled by the device and rmw operations requires to do atomic operations.
Allow to declare a dedicated function in regmap_config for
reg_update_bits in no bus configuration.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20211104150040.1260-1-ansuelsmth@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ls-extirq irqchip driver accesses regmap inside its implementation
of the struct irq_chip :: irq_set_type method, and currently regmap
only knows to lock using normal spinlocks. But the method above wants
raw spinlock context, so this isn't going to work and triggers a
"[ BUG: Invalid wait context ]" splat.
The best we can do given the arrangement of the code is to patch regmap
and the syscon driver: regmap to support raw spinlocks, and syscon to
request them on behalf of its ls-extirq consumer.
Link: https://lore.kernel.org/lkml/20210825135438.ubcuxm5vctt6ne2q@skbuf/T/#u
Vladimir Oltean (2):
regmap: teach regmap to use raw spinlocks if requested in the config
mfd: syscon: request a regmap with raw spinlocks for some devices
drivers/base/regmap/internal.h | 4 ++++
drivers/base/regmap/regmap.c | 35 +++++++++++++++++++++++++++++-----
drivers/mfd/syscon.c | 16 ++++++++++++++++
include/linux/regmap.h | 2 ++
4 files changed, 52 insertions(+), 5 deletions(-)
--
2.25.1
base-commit: 6efb943b86
Some drivers might access regmap in a context where a raw spinlock is
held. An example is drivers/irqchip/irq-ls-extirq.c, which calls
regmap_update_bits() from struct irq_chip :: irq_set_type, which is a
method called by __irq_set_trigger() under the desc->lock raw spin lock.
Since desc->lock is a raw spin lock and the regmap internal lock for
mmio is a plain spinlock (which can become sleepable on RT), this is an
invalid locking scheme and we get a splat stating that this is a
"[ BUG: Invalid wait context ]".
It seems reasonable for regmap to have an option use a raw spinlock too,
so add that in the config such that drivers can request it.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210825205041.927788-2-vladimir.oltean@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The reg_fields array fed to {devm_}regmap_field_bulk_alloc is currently
not const, which is not correct on semantics (the functions shouldn't
change reg_field contents) and prevents pre-defined const reg_field
array to be used.
As the implementation of this function doesn't change the content of it,
just add const to its prototype.
Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
Link: https://lore.kernel.org/r/20210802063741.76301-1-icenowy@sipeed.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some interrupt controllers have inverted status register:
cleared bits is active interrupts and set bits is inactive interrupts,
so add inverted status support to the framework.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Link: https://lore.kernel.org/r/20210525034204.5272-1-fido_max@inbox.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The RTL8231 GPIO and LED expander can be configured for use as an MDIO or SMI
bus device. Currently only the MDIO mode is supported, although SMI mode
support should be fairly straightforward, once an SMI bus driver is available.
Provided features by the RTL8231:
- Up to 37 GPIOs
- Configurable drive strength: 8mA or 4mA (currently unsupported)
- Input debouncing on high GPIOs (currently unsupported)
- Up to 88 LEDs in multiple scan matrix groups
- On, off, or one of six toggling intervals
- "single-color mode": 2×36 single color LEDs + 8 bi-color LEDs
- "bi-color mode": (12 + 2×6) bi-color LEDs + 24 single color LEDs
- Up to one PWM output (currently unsupported)
- Fixed duty cycle, 8 selectable frequencies (1.2kHz - 4.8kHz)
Register access is provided through a new MDIO regmap provider. The GPIO
controller uses gpio-regmap, although a patch is required to support a
limitation of the chip.
There remain some log warnings when probing the device, possibly due to the way
I'm using the MFD subsystem. Would it be possible to avoid these?
[ 2.602242] rtl8231-pinctrl: Failed to locate of_node [id: -2]
[ 2.609380] rtl8231-pinctrl rtl8231-pinctrl.0.auto: no of_node; not parsing pinctrl DT
When no 'leds' sub-node is specified:
[ 2.922262] rtl8231-leds: Failed to locate of_node [id: -2]
[ 2.967149] rtl8231-leds rtl8231-leds.1.auto: no of_node; not parsing pinctrl DT
[ 2.975673] rtl8231-leds rtl8231-leds.1.auto: scan mode missing or invalid
[ 2.983531] rtl8231-leds: probe of rtl8231-leds.1.auto failed with error -22
Changes since v1:
- Reintroduce MDIO regmap, with fixed Kconfig dependencies
- Add configurable dir/value order for gpio-regmap direction_out call
- Drop allocations for regmap fields that are used only on init
- Move some definitions to MFD header
- Add PM ops to replace driver remove for MFD
- Change pinctrl driver to (modified) gpio-regmap
- Change leds driver to use fwnode
Link: https://lore.kernel.org/lkml/cover.1620735871.git.sander@svanheule.net/
Changes since RFC:
- Dropped MDIO regmap interface. I was unable to resolve the Kconfig
dependency issue, so have reverted to using regmap_config.reg_read/write.
- Added pinctrl support
- Added LED support
- Changed root device to MFD, with pinctrl and leds child devices. Root
device is now an mdio_device driver.
Link: https://lore.kernel.org/linux-gpio/cover.1617914861.git.sander@svanheule.net/
Sander Vanheule (7):
regmap: Add MDIO bus support
gpio: regmap: Add configurable dir/value order
dt-bindings: leds: Binding for RTL8231 scan matrix
dt-bindings: mfd: Binding for RTL8231
mfd: Add RTL8231 core device
pinctrl: Add RTL8231 pin control and GPIO support
leds: Add support for RTL8231 LED scan matrix
.../bindings/leds/realtek,rtl8231-leds.yaml | 159 ++++++++
.../bindings/mfd/realtek,rtl8231.yaml | 202 ++++++++++
drivers/base/regmap/Kconfig | 6 +-
drivers/base/regmap/Makefile | 1 +
drivers/base/regmap/regmap-mdio.c | 57 +++
drivers/gpio/gpio-regmap.c | 20 +-
drivers/leds/Kconfig | 10 +
drivers/leds/Makefile | 1 +
drivers/leds/leds-rtl8231.c | 293 ++++++++++++++
drivers/mfd/Kconfig | 9 +
drivers/mfd/Makefile | 1 +
drivers/mfd/rtl8231.c | 153 +++++++
drivers/pinctrl/Kconfig | 11 +
drivers/pinctrl/Makefile | 1 +
drivers/pinctrl/pinctrl-rtl8231.c | 377 ++++++++++++++++++
include/linux/gpio/regmap.h | 3 +
include/linux/mfd/rtl8231.h | 57 +++
include/linux/regmap.h | 36 ++
18 files changed, 1393 insertions(+), 4 deletions(-)
create mode 100644 Documentation/devicetree/bindings/leds/realtek,rtl8231-leds.yaml
create mode 100644 Documentation/devicetree/bindings/mfd/realtek,rtl8231.yaml
create mode 100644 drivers/base/regmap/regmap-mdio.c
create mode 100644 drivers/leds/leds-rtl8231.c
create mode 100644 drivers/mfd/rtl8231.c
create mode 100644 drivers/pinctrl/pinctrl-rtl8231.c
create mode 100644 include/linux/mfd/rtl8231.h
base-commit: 6efb943b86
--
2.31.1
Enable drivers to configure and modify "virtual" registers, which are
non-standard registers that further configure irq type on some devices.
Since they are non-standard, enable drivers to configure them according
to their particular idiosyncrasies by specifying an optional callback
function while registering with the framework.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Link: https://lore.kernel.org/r/07e058cdec2297d15c95c825aa0263064d962d5a.1616613838.git.gurus@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add "virtual" registers support to handle any irq configuration
registers in addition to the ones the framework currently supports
(status, mask, unmask, wake, type and ack). These are non-standard
registers that further configure irq type on some devices, so enable the
framework to add a variable number of them.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Link: https://lore.kernel.org/r/a1787067004b0e11cb960319082764397469215a.1616613838.git.gurus@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm's MFD chips have a top level interrupt status register and
sub-irqs (peripherals). When a bit in the main status register goes
high, it means that the peripheral corresponding to that bit has an
unserviced interrupt. If the bit is not set, this means that the
corresponding peripheral does not.
Commit a2d21848d9 ("regmap: regmap-irq: Add main status register
support") introduced the sub-irq logic that is currently applied only
when reading status registers, but not for any other functions like acking
or masking. Extend the use of sub-irq to all other functions, with two
caveats regarding the specification of offsets:
- Each member of the sub_reg_offsets array should be of length 1
- The specified offsets should be the unequal strides for each sub-irq
device.
In QCOM's case, all the *_base registers are to be configured to the
base addresses of the first sub-irq group, with offsets of each
subsequent group calculated as a difference from these addresses.
Continuing from the example mentioned in the cover letter:
/*
* Address of MISC_INT_MASK = 0x1011
* Address of TEMP_ALARM_INT_MASK = 0x2011
* Address of GPIO01_INT_MASK = 0x3011
*
* Calculate offsets as:
* offset_0 = 0x1011 - 0x1011 = 0 (to access MISC's
* registers)
* offset_1 = 0x2011 - 0x1011 = 0x1000
* offset_2 = 0x3011 - 0x1011 = 0x2000
*/
static unsigned int sub_unit0_offsets[] = {0};
static unsigned int sub_unit1_offsets[] = {0x1000};
static unsigned int sub_unit2_offsets[] = {0x2000};
static struct regmap_irq_sub_irq_map chip_sub_irq_offsets[] = {
REGMAP_IRQ_MAIN_REG_OFFSET(sub_unit0_offsets),
REGMAP_IRQ_MAIN_REG_OFFSET(sub_unit0_offsets),
REGMAP_IRQ_MAIN_REG_OFFSET(sub_unit0_offsets),
};
static struct regmap_irq_chip chip_irq_chip = {
--------8<--------
.not_fixed_stride = true,
.mask_base = MISC_INT_MASK,
.type_base = MISC_INT_TYPE,
.ack_base = MISC_INT_ACK,
.sub_reg_offsets = chip_sub_irq_offsets,
--------8<--------
};
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Link: https://lore.kernel.org/r/526562423eaa58b4075362083f561841f1d6956c.1615423027.git.gurus@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The MIPI SoundWire Device Class standard will define audio functionality
beyond the scope of the existing SoundWire 1.2 standard, which is limited
to the bus and interface.
The description is inspired by the USB Audio Class, with "functions",
"entities", "control selectors", "audio clusters". The main difference
with the USB Audio class is that the devices are typically on a motherboard
and descriptors stored in platform firmware instead of being retrieved
from the device.
The current set of devices managed in this patchset are conformant with the
SDCA 0.6 specification and require dedicated drivers since the descriptors
and platform firmware specification is not complete at this time. They do
however rely on the hierarchical addressing required by the SDCA standard.
Future devices conformant with SDCA 1.0 should rely on a class driver.
This series adds support for the hierarchical SDCA addressing and extends
regmap. It then provides 3 codecs for RT711-sdca headset codec, RT1316
amplifier and RT715-scda microphone codec.
Note that the release of this code before the formal adoption of the
SDCA 1.0 specification was formally endorsed by the MIPI Board to make
sure there is no delay for Linux-based support of this specification.
Jack Yu (1):
ASoC/SoundWire: rt715-sdca: First version of rt715 sdw sdca codec
driver
Pierre-Louis Bossart (2):
soundwire: SDCA: add helper macro to access controls
regmap/SoundWire: sdw: add support for SoundWire 1.2 MBQ
Shuming Fan (2):
ASoC/SoundWire: rt1316: Add RT1316 SDCA vendor-specific driver
ASoC/SoundWire: rt711-sdca: Add RT711 SDCA vendor-specific driver
drivers/base/regmap/Kconfig | 6 +-
drivers/base/regmap/Makefile | 1 +
drivers/base/regmap/regmap-sdw-mbq.c | 101 ++
include/linux/regmap.h | 35 +
include/linux/soundwire/sdw_registers.h | 32 +
sound/soc/codecs/Kconfig | 20 +
sound/soc/codecs/Makefile | 6 +
sound/soc/codecs/rt1316-sdw.c | 756 ++++++++++++
sound/soc/codecs/rt1316-sdw.h | 115 ++
sound/soc/codecs/rt711-sdca-sdw.c | 424 +++++++
sound/soc/codecs/rt711-sdca-sdw.h | 101 ++
sound/soc/codecs/rt711-sdca.c | 1481 +++++++++++++++++++++++
sound/soc/codecs/rt711-sdca.h | 246 ++++
sound/soc/codecs/rt715-sdca-sdw.c | 278 +++++
sound/soc/codecs/rt715-sdca-sdw.h | 170 +++
sound/soc/codecs/rt715-sdca.c | 936 ++++++++++++++
sound/soc/codecs/rt715-sdca.h | 124 ++
17 files changed, 4831 insertions(+), 1 deletion(-)
create mode 100644 drivers/base/regmap/regmap-sdw-mbq.c
create mode 100644 sound/soc/codecs/rt1316-sdw.c
create mode 100644 sound/soc/codecs/rt1316-sdw.h
create mode 100644 sound/soc/codecs/rt711-sdca-sdw.c
create mode 100644 sound/soc/codecs/rt711-sdca-sdw.h
create mode 100644 sound/soc/codecs/rt711-sdca.c
create mode 100644 sound/soc/codecs/rt711-sdca.h
create mode 100644 sound/soc/codecs/rt715-sdca-sdw.c
create mode 100644 sound/soc/codecs/rt715-sdca-sdw.h
create mode 100644 sound/soc/codecs/rt715-sdca.c
create mode 100644 sound/soc/codecs/rt715-sdca.h
base-commit: 3650b228f8
--
2.17.1
The SoundWire 1.1 specification only allowed for reads and writes of
bytes. The SoundWire 1.2 specification adds a new capability to
transfer "Multi-Byte Quantities" (MBQ) across the bus. The transfers
still happens one-byte-at-a-time, but the update is atomic.
For example when writing a 16-bit volume, the first byte transferred
is only taken into account when the second byte is successfully
transferred.
The mechanism is symmetrical for read and writes:
- On a read, the address of the last byte to be read is modified by
setting the MBQ bit
- On a write, the address of all but the last byte to be written are
modified by setting the MBQ bit. The address for the last byte relies
on the MBQ bit being cleared.
The current definitions for MBQ-based controls in the SDCA draft
standard are limited to 16 bits for volumes, so for now this is the
only supported format. An update will be provided if and when support
for 24-bit and 32-bit values is specified by the SDCA standard.
One possible objection is that this code could have been handled with
regmap-sdw.c. However this is a new spec addition not handled by every
SoundWire 1.1 and non-SDCA device, so there's no reason to load code
that will never be used.
Also in practice it's extremely unlikely that CONFIG_REGMAP would not
be selected with CONFIG_REGMAP_MBQ selected. However there's no
functional dependency between the two modules so they can be selected
separately.
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201103172226.4278-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On some platforms (eg armv7 due to the CONFIG_ARM_DMA_MEM_BUFFERABLE)
MMIO R/W operations always add memory barriers which can increase load,
decrease battery life or in general reduce performance unnecessarily
on devices which access a lot of configuration registers and where
ordering does not matter (eg. media accelerators like the Verisilicon /
Hantro video decoders).
Drivers used to call the relaxed MMIO variants directly but since they
are now accessing the MMIO registers via regmaps (to compensate for
different VPU HW reg layouts via regmap fields), there is a need for a
relaxed API / config to preserve existing behaviour.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Link: https://lore.kernel.org/r/20201014203024.954369-1-adrian.ratiu@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For particular codec HWs have requirement to toggle interrupt clear
register twice 0->1->0. To accommodate it, need to add one more field
(clear_ack) in the regmap_irq struct and update regmap-irq driver to
support it.
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Link: https://lore.kernel.org/r/1601907440-13373-1-git-send-email-lkasam@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Useful for devices with many fields.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9yPoATHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JsoB/9zhtYrqKbof0AKuMfEeO+pPo4dC/9l
O7ENgSXCb9PWy0auVpU62ISXBPadbbrQXXe3hJ1Zof5q17lYqbaLM7Uem3bxIYtc
0HHRIb49R1sP+99T2JB3RDu/ykzHJsfxCkLgMR5MvBgS5e3KKf0SqZgNSVTYT4Y5
oPt81sxW56Z8FLrLn0j1sVDXlro4/uBpDOcHyzgq4GWgQ6ACvnIOH+PQUTTcGBfT
LtIkRMO8mHNKsDCy9Qy12NRsaparIbYb7KKEY9IR+6TN+qJ/g5PJQcPmsU6b0NIl
pb7fv4IRTvPDaEPa1g20U88qkSE5H3PXp88R3y/JbSMuFJwWwS2AGwYd
=L+6w
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9yPpwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0PkDB/9ybt51NqJWyU3JaleY7otD2QvCmvl6
2dzpDncfjYZ8GOhvju74BQM9h/m9EHzb5FQ1yLMKEeICXZwxkDgHiqMLYLN1e6wx
ug5U6lvbT1TmeBa7IJYNNSGH2BKeIDM5Hm2zVvMpEJhF2Y9uAE0HqxjGL3CfbUOv
R2o2K3wgax83FfX86wmYNgkkp4Ri1qviD1Jr90zzFZRr0FAjiyrFHXdfdvK/wUx1
5n9wg+aIehQr1a8cKYQaqWd3HZR6pofmOj1cO4n/By+VEYRWaVds8OKUrqimZ2mE
moX9+ooY3eFdmS6kgtA31bgBFjKxfMNaTzTa4B3kikmxSOKMupQejBn9
=G3GG
-----END PGP SIGNATURE-----
Merge tag 'regmap-field-bulk-api' into regmap-5.10
regmap: Add a bulk field API
Useful for devices with many fields.
Usage of regmap_field_alloc becomes much overhead when number of fields
exceed more than 3.
QCOM LPASS driver has extensively converted to use regmap_fields.
Using new bulk api to allocate fields makes it much more cleaner code to read!
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Link: https://lore.kernel.org/r/20200925164856.10315-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Regmap can't sleep if spinlock is used for the locking protection.
This patch fixes regression caused by a previous commit that switched
regmap to use fsleep() and this broke Amlogic S922X platform.
This patch adds new configuration option for regmap users, allowing to
specify whether regmap operations can sleep and assuming that sleep is
allowed if mutex is used for the regmap locking protection.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 2b32d2f7ce ("regmap: Use flexible sleep")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200902141843.6591-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch add support for regmap APIs that are intended to be used by
the drivers of some SPI slave chips which integrate the "SPI slave to
Avalon Master Bridge" (spi-avmm) IP.
The spi-avmm IP acts as a bridge to convert encoded streams of bytes
from the host to the chip's internal register read/write on Avalon bus.
The driver implements the register read/write operations for a generic
SPI master to access the sub devices behind spi-avmm bridge.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Reviewed-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Link: https://lore.kernel.org/r/1597822497-25107-2-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the argument to the newer fwnode_handle instead a device tree
node. Fortunately, there are no users for now. So this is an easy
change.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200706175353.16404-2-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no reason to have these as macros. Let's convert them all to
static inlines for better readability and stronger typing.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200615072313.11106-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Bartosz Golaszewski <bgolaszewski@baylibre.com>:
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
I noticed that oftentimes I use regmap_update_bits() for simple bit
setting or clearing. In this case the fourth argument is superfluous as
it's always 0 or equal to the mask argument.
This series proposes to add simple bit operations for setting, clearing
and testing specific bits with regmap.
The second patch uses all three in a driver that got recently picked into
the net-next tree.
The patches obviously target different trees so - if you're ok with
the change itself - I propose you pick the first one into your regmap
tree for v5.8 and then I'll resend the second patch to add the first
user for these macros for v5.9.
v1 -> v2:
- convert the new macros to static inline functions
v2 -> v3:
- drop unneeded ternary operator
Bartosz Golaszewski (2):
regmap: provide helpers for simple bit operations
net: ethernet: mtk-star-emac: use regmap bitops
drivers/base/regmap/regmap.c | 22 +++++
drivers/net/ethernet/mediatek/mtk_star_emac.c | 80 ++++++++-----------
include/linux/regmap.h | 36 +++++++++
3 files changed, 93 insertions(+), 45 deletions(-)
base-commit: 8f3d9f3542
--
2.26.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Looking at the Felix and Ocelot drivers, Maxim asked if it would be
possible to use them as a base for a new driver for the switch inside
NXP T1040. Turns out, it is! The result is a driver eerily similar to
Felix.
The biggest challenge seems to be getting register read/write API
generic enough to cover such wild bitfield variations between hardware
generations. There is a patch on the regmap core which I would like to
get in through the networking subsystem, if possible (and if Mark is
ok), since it's a trivial addition.
Maxim Kochetkov (4):
soc/mscc: ocelot: add MII registers description
net: mscc: ocelot: convert SYS_PAUSE_CFG register access to regfield
net: mscc: ocelot: extend watermark encoding function
net: dsa: ocelot: introduce driver for Seville VSC9953 switch
Vladimir Oltean (7):
regmap: add helper for per-port regfield initialization
net: mscc: ocelot: unexport ocelot_probe_port
net: mscc: ocelot: convert port registers to regmap
net: mscc: ocelot: convert QSYS_SWITCH_PORT_MODE and SYS_PORT_MODE to
regfields
net: dsa: ocelot: create a template for the DSA tags on xmit
net: mscc: ocelot: split writes to pause frame enable bit and to
thresholds
net: mscc: ocelot: disable flow control on NPI interface
drivers/net/dsa/ocelot/Kconfig | 12 +
drivers/net/dsa/ocelot/Makefile | 6 +
drivers/net/dsa/ocelot/felix.c | 49 +-
drivers/net/dsa/ocelot/felix_vsc9959.c | 72 +-
drivers/net/dsa/ocelot/seville.c | 742 +++++++++++++++
drivers/net/dsa/ocelot/seville.h | 50 +
drivers/net/dsa/ocelot/seville_vsc9953.c | 1064 ++++++++++++++++++++++
drivers/net/ethernet/mscc/ocelot.c | 87 +-
drivers/net/ethernet/mscc/ocelot.h | 9 +-
drivers/net/ethernet/mscc/ocelot_board.c | 21 +-
drivers/net/ethernet/mscc/ocelot_io.c | 18 +-
drivers/net/ethernet/mscc/ocelot_regs.c | 57 ++
include/linux/regmap.h | 8 +
include/soc/mscc/ocelot.h | 68 +-
include/soc/mscc/ocelot_dev.h | 78 --
include/soc/mscc/ocelot_qsys.h | 13 -
include/soc/mscc/ocelot_sys.h | 23 -
net/dsa/tag_ocelot.c | 21 +-
18 files changed, 2196 insertions(+), 202 deletions(-)
create mode 100644 drivers/net/dsa/ocelot/seville.c
create mode 100644 drivers/net/dsa/ocelot/seville.h
create mode 100644 drivers/net/dsa/ocelot/seville_vsc9953.c
base-commit: 8f3d9f3542
--
2.25.1
In many instances regmap_update_bits() is used for simple bit setting
and clearing. In these cases the last argument is redundant and we can
hide it with a static inline function.
This adds three new helpers for simple bit operations: set_bits,
clear_bits and test_bits (the last one defined as a regular function).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200528154503.26304-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Similar to the standalone regfields, add an initializer for the users
who need to set .id_size and .id_offset in order to use the
regmap_fields_update_bits_base API.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200527234113.2491988-2-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the implementation of the macro regmap_field_read_poll_timeout()
by using the macro read_poll_timeout().
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Link: https://lore.kernel.org/r/20200420134647.9121-3-zhengdejin5@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the implementation of the macro regmap_read_poll_timeout()
by using the macro read_poll_timeout().
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Link: https://lore.kernel.org/r/20200420134647.9121-2-zhengdejin5@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Kontron sl28cpld is a board management chip providing gpio, pwm, fan
monitoring and an interrupt controller. For now this controller is used on
the Kontron SMARC-sAL28 board. But because of its flexible nature, it
might also be used on other boards in the future. The individual blocks
(like gpio, pwm, etc) are kept intentionally small. The MFD core driver
then instantiates different (or multiple of the same) blocks. It also
provides the register layout so it might be updated in the future without a
device tree change; and support other boards with a different layout or
functionalities.
See also [1] for more information.
This is my first take of a MFD driver. I don't know whether the subsystem
maintainers should only be CCed on the patches which affect the subsystem
or on all patches for this series. I've chosen the latter so you can get a
more complete picture.
[1] https://lore.kernel.org/linux-devicetree/0e3e8204ab992d75aa07fc36af7e4ab2@walle.cc/
Changes since v1:
- use of_match_table in all drivers, needed for automatic module loading,
when using OF_MFD_CELL()
- add new gpio-regmap.c which adds a generic regmap gpio_chip implemention
- new patch for reqmap_irq, so we can reuse its implementation
- remove almost any code from gpio-sl28cpld.c, instead use gpio-regmap and
regmap-irq
- change the handling of the mfd core vs device tree nodes; add a new
property "of_reg" to the mfd_cell struct which, when set, is matched to
the unit-address of the device tree nodes.
- fix sl28cpld watchdog when it is not initialized by the bootloader.
Explicitly set the operation mode.
- also add support for kontron,assert-wdt-timeout-pin in sl28cpld-wdt.
As suggested by Bartosz Golaszewski:
- define registers as hex
- make gpio enum uppercase
- move parent regmap check before memory allocation
- use device_property_read_bool() instead of the of_ version
- mention the gpio flavors in the bindings documentation
As suggested by Guenter Roeck:
- cleanup #includes and sort them
- use devm_watchdog_register_device()
- use watchdog_stop_on_reboot()
- provide a Documentation/hwmon/sl28cpld.rst
- cleaned up the weird tristate->bool and I2C=y issue. Instead mention
that the MFD driver is bool because of the following intc patch
- removed the SL28CPLD_IRQ typo
As suggested by Rob Herring:
- combine all dt bindings docs into one patch
- change the node name for all gpio flavors to "gpio"
- removed the interrupts-extended rule
- cleaned up the unit-address space, see above
Michael Walle (16):
include/linux/ioport.h: add helper to define REG resource constructs
mfd: mfd-core: Don't overwrite the dma_mask of the child device
mfd: mfd-core: match device tree node against reg property
regmap-irq: make it possible to add irq_chip do a specific device node
dt-bindings: mfd: Add bindings for sl28cpld
mfd: Add support for Kontron sl28cpld management controller
irqchip: add sl28cpld interrupt controller support
watchdog: add support for sl28cpld watchdog
pwm: add support for sl28cpld PWM controller
gpio: add a reusable generic gpio_chip using regmap
gpio: add support for the sl28cpld GPIO controller
hwmon: add support for the sl28cpld hardware monitoring controller
arm64: dts: freescale: sl28: enable sl28cpld
arm64: dts: freescale: sl28: map GPIOs to input events
arm64: dts: freescale: sl28: enable LED support
arm64: dts: freescale: sl28: enable fan support
.../bindings/gpio/kontron,sl28cpld-gpio.yaml | 51 +++
.../hwmon/kontron,sl28cpld-hwmon.yaml | 27 ++
.../bindings/mfd/kontron,sl28cpld.yaml | 162 +++++++++
.../bindings/pwm/kontron,sl28cpld-pwm.yaml | 35 ++
.../watchdog/kontron,sl28cpld-wdt.yaml | 35 ++
Documentation/hwmon/sl28cpld.rst | 36 ++
.../fsl-ls1028a-kontron-kbox-a-230-ls.dts | 14 +
.../fsl-ls1028a-kontron-sl28-var3-ads2.dts | 9 +
.../freescale/fsl-ls1028a-kontron-sl28.dts | 124 +++++++
drivers/base/regmap/regmap-irq.c | 84 ++++-
drivers/gpio/Kconfig | 15 +
drivers/gpio/Makefile | 2 +
drivers/gpio/gpio-regmap.c | 321 ++++++++++++++++++
drivers/gpio/gpio-sl28cpld.c | 187 ++++++++++
drivers/hwmon/Kconfig | 10 +
drivers/hwmon/Makefile | 1 +
drivers/hwmon/sl28cpld-hwmon.c | 152 +++++++++
drivers/irqchip/Kconfig | 3 +
drivers/irqchip/Makefile | 1 +
drivers/irqchip/irq-sl28cpld.c | 99 ++++++
drivers/mfd/Kconfig | 21 ++
drivers/mfd/Makefile | 2 +
drivers/mfd/mfd-core.c | 31 +-
drivers/mfd/sl28cpld.c | 154 +++++++++
drivers/pwm/Kconfig | 10 +
drivers/pwm/Makefile | 1 +
drivers/pwm/pwm-sl28cpld.c | 204 +++++++++++
drivers/watchdog/Kconfig | 11 +
drivers/watchdog/Makefile | 1 +
drivers/watchdog/sl28cpld_wdt.c | 242 +++++++++++++
include/linux/gpio-regmap.h | 88 +++++
include/linux/ioport.h | 5 +
include/linux/mfd/core.h | 26 +-
include/linux/regmap.h | 10 +
34 files changed, 2142 insertions(+), 32 deletions(-)
create mode 100644 Documentation/devicetree/bindings/gpio/kontron,sl28cpld-gpio.yaml
create mode 100644 Documentation/devicetree/bindings/hwmon/kontron,sl28cpld-hwmon.yaml
create mode 100644 Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml
create mode 100644 Documentation/devicetree/bindings/pwm/kontron,sl28cpld-pwm.yaml
create mode 100644 Documentation/devicetree/bindings/watchdog/kontron,sl28cpld-wdt.yaml
create mode 100644 Documentation/hwmon/sl28cpld.rst
create mode 100644 drivers/gpio/gpio-regmap.c
create mode 100644 drivers/gpio/gpio-sl28cpld.c
create mode 100644 drivers/hwmon/sl28cpld-hwmon.c
create mode 100644 drivers/irqchip/irq-sl28cpld.c
create mode 100644 drivers/mfd/sl28cpld.c
create mode 100644 drivers/pwm/pwm-sl28cpld.c
create mode 100644 drivers/watchdog/sl28cpld_wdt.c
create mode 100644 include/linux/gpio-regmap.h
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Add a new function regmap_add_irq_chip_np() with its corresponding
devm_regmap_add_irq_chip_np() variant. Sometimes one want to register
the IRQ domain on a different device node that the one of the regmap
node. For example when using a MFD where there are different interrupt
controllers and particularly for the generic regmap gpio_chip/irq_chip
driver. In this case it is not desireable to have the IRQ domain on
the parent node.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200402203656.27047-5-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a macro 'regmap_read_poll_timeout_atomic' that works
similar to 'readx_poll_timeout_atomic' defined in linux/iopoll.h; This
is atomic version of already available 'regmap_read_poll_timeout' macro.
It should be noted that above atomic macro cannot be used by all regmaps.
If the regmap is set up for atomic use (flat or no cache and MMIO) then
only it can use.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1578546590-24737-1-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aidan MacDonald