commit 55251fbdf0 upstream.
This reverts commit 748dc0b65e.
Partial zone append completions cannot be supported as there is no
guarantees that the fragmented data will be written sequentially in the
same manner as with a full command. Commit 748dc0b65e ("block: fix
partial zone append completion handling in req_bio_endio()") changed
req_bio_endio() to always advance a partially failed BIO by its full
length, but this can lead to incorrect accounting. So revert this
change and let low level device drivers handle this case by always
failing completely zone append operations. With this revert, users will
still see an IO error for a partially completed zone append BIO.
Fixes: 748dc0b65e ("block: fix partial zone append completion handling in req_bio_endio()")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240328004409.594888-2-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9e2a5b00a upstream.
"PM runtime functions" was been added in sdhci-omap driver in commit
f433e8aac6 ("mmc: sdhci-omap: Implement PM runtime functions") along
with "card power off and enable aggressive PM" in commit 3edf588e7f
("mmc: sdhci-omap: Allow SDIO card power off and enable aggressive PM").
Since then, the sdhci-omap driver doesn't work using mmc-hs200 mode
due to the tuning values being lost during a pm transition.
As for the sdhci_am654 driver, request a new tuning sequence before
suspend (sdhci_omap_runtime_suspend()), otherwise the device will
trigger cache flush error:
mmc1: cache flush error -110 (ETIMEDOUT)
mmc1: error -110 doing aggressive suspend
followed by I/O errors produced by fdisk -l /dev/mmcblk1boot1:
I/O error, dev mmcblk1boot0, sector 64384 op 0x0:(READ) flags 0x80700 phys_seg 1
prio class 2
I/O error, dev mmcblk1boot1, sector 64384 op 0x0:(READ) flags 0x80700 phys_seg 1
prio class 2
I/O error, dev mmcblk1boot1, sector 64384 op 0x0:(READ) flags 0x0 phys_seg 1
prio class 2
Buffer I/O error on dev mmcblk1boot1, logical block 8048, async page read
I/O error, dev mmcblk1boot0, sector 64384 op 0x0:(READ) flags 0x0 phys_seg 1
prio class 2
Buffer I/O error on dev mmcblk1boot0, logical block 8048, async page read
Don't re-tune if auto retuning is supported in HW (when SDHCI_TUNING_MODE_3
is available).
Link: https://lore.kernel.org/all/2e5f1997-564c-44e4-b357-6343e0dae7ab@smile.fr
Fixes: f433e8aac6 ("mmc: sdhci-omap: Implement PM runtime functions")
Signed-off-by: Romain Naour <romain.naour@skf.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240315234444.816978-1-romain.naour@smile.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 549aa9678a upstream.
After the linked LLVM change, the build fails with
CONFIG_LD_ORPHAN_WARN_LEVEL="error", which happens with allmodconfig:
ld.lld: error: vmlinux.a(init/main.o):(.hexagon.attributes) is being placed in '.hexagon.attributes'
Handle the attributes section in a similar manner as arm and riscv by
adding it after the primary ELF_DETAILS grouping in vmlinux.lds.S, which
fixes the error.
Link: https://lkml.kernel.org/r/20240319-hexagon-handle-attributes-section-vmlinux-lds-s-v1-1-59855dab8872@kernel.org
Fixes: 113616ec5b ("hexagon: select ARCH_WANT_LD_ORPHAN_WARN")
Link: 31f4b329c8
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Brian Cain <bcain@quicinc.com>
Cc: Bill Wendling <morbo@google.com>
Cc: Justin Stitt <justinstitt@google.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2aea94ac14 upstream.
In NOMMU kernel the value of linux_binprm::p is the offset inside the
temporary program arguments array maintained in separate pages in the
linux_binprm::page. linux_binprm::exec being a copy of linux_binprm::p
thus must be adjusted when that array is copied to the user stack.
Without that adjustment the value passed by the NOMMU kernel to the ELF
program in the AT_EXECFN entry of the aux array doesn't make any sense
and it may break programs that try to access memory pointed to by that
entry.
Adjust linux_binprm::exec before the successful return from the
transfer_args_to_stack().
Cc: <stable@vger.kernel.org>
Fixes: b6a2fea393 ("mm: variable length argument support")
Fixes: 5edc2a5123 ("binfmt_elf_fdpic: wire up AT_EXECFD, AT_EXECFN, AT_SECURE")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20240320182607.1472887-1-jcmvbkbc@gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 045a5b645d upstream.
Since the dump_data (struct iwl_fwrt_dump_data) is a union,
it's not safe to unconditionally access and use the 'trig'
member, it might be 'desc' instead. Access it only if it's
known to be 'trig' rather than 'desc', i.e. if ini-debug
is present.
Cc: stable@vger.kernel.org
Fixes: 0eb50c674a ("iwlwifi: yoyo: send hcmd to fw after dump collection completes.")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240319100755.e2976bc58b29.I72fbd6135b3623227de53d8a2bb82776066cb72b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f2bdb3c5e upstream.
When moving a station out of a VLAN and deleting the VLAN afterwards, the
fast_rx entry still holds a pointer to the VLAN's netdev, which can cause
use-after-free bugs. Fix this by immediately calling ieee80211_check_fast_rx
after the VLAN change.
Cc: stable@vger.kernel.org
Reported-by: ranygh@riseup.net
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://msgid.link/20240316074336.40442-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74098a989b upstream.
At the moment scrub_supers() doesn't grab the super block's location via
the zoned device aware btrfs_sb_log_location() but via btrfs_sb_offset().
This leads to checksum errors on 'scrub' as we're not accessing the
correct location of the super block.
So use btrfs_sb_log_location() for getting the super blocks location on
scrub.
Reported-by: WA AM <waautomata@gmail.com>
Link: http://lore.kernel.org/linux-btrfs/CANU2Z0EvUzfYxczLgGUiREoMndE9WdQnbaawV5Fv5gNXptPUKw@mail.gmail.com
CC: stable@vger.kernel.org # 5.15+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8b70c7f86 upstream.
Commit f4a9f21941 ("btrfs: do not delete unused block group if it may be
used soon") changed the behaviour of deleting unused block-groups on zoned
filesystems. Starting with this commit, we're using
btrfs_space_info_used() to calculate the number of used bytes in a
space_info. But btrfs_space_info_used() also accounts
btrfs_space_info::bytes_zone_unusable as used bytes.
So if a block group is 100% zone_unusable it is skipped from the deletion
step.
In order not to skip fully zone_unusable block-groups, also check if the
block-group has bytes left that can be used on a zoned filesystem.
Fixes: f4a9f21941 ("btrfs: do not delete unused block group if it may be used soon")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61d130f261 upstream.
Avoid a type mismatch warning in max() by switching to max_t() and
providing the type explicitly.
Fixes: 3cb4a48275 ("efi/libstub: fix efi_random_alloc() ...")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d21f5a59ea upstream.
The pure EFI stub entry point does not take a struct boot_params from
the boot loader, but creates it from scratch, and populates only the
fields that still have meaning in this context (command line, initrd
base and size, etc)
The original mixed mode implementation used the EFI handover protocol
instead, where the boot loader (i.e., GRUB) populates a boot_params
struct and passes it to a special Linux specific EFI entry point that
takes the boot_params pointer as its third argument.
When the new mixed mode implementation was introduced, using a special
32-bit PE entrypoint in the 64-bit kernel, it adopted the pure approach,
and relied on the EFI stub to create the struct boot_params. This is
preferred because it makes the bootloader side much easier to implement,
as it does not need any x86-specific knowledge on how struct boot_params
and struct setup_header are put together. This mixed mode implementation
was adopted by systemd-boot version 252 and later.
When commit
e2ab9eab32 ("x86/boot/compressed: Move 32-bit entrypoint code into .text section")
refactored this code and moved it out of head_64.S, the fact that ESI
was populated with the address of the base of the image was overlooked,
and to simplify the code flow, ESI is now zeroed and stored to memory
unconditionally in shared code, so that the NULL-ness of that variable
can still be used later to determine which mixed mode boot protocol is
in use.
With ESI pointing to the base of the image, it can serve as a struct
boot_params pointer for startup_32(), which only accesses the init_data
and kernel_alignment fields (and the scratch field as a temporary
stack). Zeroing ESI means that those accesses produce garbage now, even
though things appear to work if the first page of memory happens to be
zeroed, and the region right before LOAD_PHYSICAL_ADDR (== 16 MiB)
happens to be free.
The solution is to pass a special, temporary struct boot_params to
startup_32() via ESI, one that is sufficient for getting it to create
the page tables correctly and is discarded right after. This involves
setting a minimal alignment of 4k, only to get the statically allocated
page tables line up correctly, and setting init_size to the executable
image size (_end - startup_32). This ensures that the page tables are
covered by the static footprint of the PE image.
Given that EFI boot no longer calls the decompressor and no longer pads
the image to permit the decompressor to execute in place, the same
temporary struct boot_params should be used in the EFI handover protocol
based mixed mode implementation as well, to prevent the page tables from
being placed outside of allocated memory.
Fixes: e2ab9eab32 ("x86/boot/compressed: Move 32-bit entrypoint code into .text section")
Cc: <stable@kernel.org> # v6.1+
Closes: https://lore.kernel.org/all/20240321150510.GI8211@craftyguy.net/
Reported-by: Clayton Craft <clayton@craftyguy.net>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4624b346cf upstream.
If initrd data is larger than 2Gb, we'll eventually fail to write to the
/initrd.image file when we hit that limit, unless O_LARGEFILE is set.
Link: https://lkml.kernel.org/r/20240317221522.896040-1-jsperbeck@google.com
Signed-off-by: John Sperbeck <jsperbeck@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tail pages in a THP can have swap entry information stored in their
private field. When migrating to a new page, all tail pages of the new
page need to update ->private to avoid future data corruption.
This fix is stable-only, since after commit 07e09c483c ("mm/huge_memory:
work on folio->swap instead of page->private when splitting folio"),
subpages of a swapcached THP no longer requires the maintenance.
Adding THPs to the swapcache was introduced in commit
38d8b4e6bd ("mm, THP, swap: delay splitting THP during swap out"),
where each subpage of a THP added to the swapcache had its own swapcache
entry and required the ->private field to point to the correct swapcache
entry. Later, when THP migration functionality was implemented in commit
616b837153 ("mm: thp: enable thp migration in generic path"),
it initially did not handle the subpages of swapcached THPs, failing to
update their ->private fields or replace the subpage pointers in the
swapcache. Subsequently, commit e71769ae52 ("mm: enable thp migration
for shmem thp") addressed the swapcache update aspect. This patch fixes
the update of subpage ->private fields.
Closes: https://lore.kernel.org/linux-mm/1707814102-22682-1-git-send-email-quic_charante@quicinc.com/
Fixes: 616b837153 ("mm: thp: enable thp migration in generic path")
Signed-off-by: Zi Yan <ziy@nvidia.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reported-and-tested-by: Charan Teja Kalla <quic_charante@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c811d403a upstream.
The early startup code executes from a 1:1 mapping of memory, which
differs from the mapping that the code was linked and/or relocated to
run at. The latter mapping is not active yet at this point, and so
symbol references that rely on it will fault.
Given that the core kernel is built without -fPIC, symbol references are
typically emitted as absolute, and so any such references occuring in
the early startup code will therefore crash the kernel.
While an attempt was made to work around this for the early SEV/SME
startup code, by forcing RIP-relative addressing for certain global
SEV/SME variables via inline assembly (see snp_cpuid_get_table() for
example), RIP-relative addressing must be pervasively enforced for
SEV/SME global variables when accessed prior to page table fixups.
__startup_64() already handles this issue for select non-SEV/SME global
variables using fixup_pointer(), which adjusts the pointer relative to a
`physaddr` argument. To avoid having to pass around this `physaddr`
argument across all functions needing to apply pointer fixups, introduce
a macro RIP_RELATIVE_REF() which generates a RIP-relative reference to
a given global variable. It is used where necessary to force
RIP-relative accesses to global variables.
For backporting purposes, this patch makes no attempt at cleaning up
other occurrences of this pattern, involving either inline asm or
fixup_pointer(). Those will be addressed later.
[ bp: Call it "rip_rel_ref" everywhere like other code shortens
"rIP-relative reference" and make the asm wrapper __always_inline. ]
Co-developed-by: Kevin Loughlin <kevinloughlin@google.com>
Signed-off-by: Kevin Loughlin <kevinloughlin@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/all/20240130220845.1978329-1-kevinloughlin@google.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2995674833 upstream.
It was meant well at the time but nothing's using it so get rid of it.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240202163510.GDZb0Zvj8qOndvFOiZ@fat_crate.local
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da86eb9611 upstream.
cc_vendor is __ro_after_init and thus can be used directly.
No functional changes.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230508121957.32341-1-bp@alien8.de
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d91c53729 upstream.
It will be used in different checks in future changes. Export it directly
and provide accessor functions and stubs so this can be used in general
code when CONFIG_ARCH_HAS_CC_PLATFORM is not set.
No functional changes.
[ tglx: Add accessor functions ]
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230318115634.9392-2-bp@alien8.de
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7447d911af ]
The eventfd_ctx trigger pointer of the vfio_fsl_mc_irq object is
initially NULL and may become NULL if the user sets the trigger
eventfd to -1. The interrupt handler itself is guaranteed that
trigger is always valid between request_irq() and free_irq(), but
the loopback testing mechanisms to invoke the handler function
need to test the trigger. The triggering and setting ioctl paths
both make use of igate and are therefore mutually exclusive.
The vfio-fsl-mc driver does not make use of irqfds, nor does it
support any sort of masking operations, therefore unlike vfio-pci
and vfio-platform, the flow can remain essentially unchanged.
Cc: Diana Craciun <diana.craciun@oss.nxp.com>
Cc: <stable@vger.kernel.org>
Fixes: cc0ee20bd9 ("vfio/fsl-mc: trigger an interrupt via eventfd")
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20240308230557.805580-8-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 675daf435e ]
The vfio-platform SET_IRQS ioctl currently allows loopback triggering of
an interrupt before a signaling eventfd has been configured by the user,
which thereby allows a NULL pointer dereference.
Rather than register the IRQ relative to a valid trigger, register all
IRQs in a disabled state in the device open path. This allows mask
operations on the IRQ to nest within the overall enable state governed
by a valid eventfd signal. This decouples @masked, protected by the
@locked spinlock from @trigger, protected via the @igate mutex.
In doing so, it's guaranteed that changes to @trigger cannot race the
IRQ handlers because the IRQ handler is synchronously disabled before
modifying the trigger, and loopback triggering of the IRQ via ioctl is
safe due to serialization with trigger changes via igate.
For compatibility, request_irq() failures are maintained to be local to
the SET_IRQS ioctl rather than a fatal error in the open device path.
This allows, for example, a userspace driver with polling mode support
to continue to work regardless of moving the request_irq() call site.
This necessarily blocks all SET_IRQS access to the failed index.
Cc: Eric Auger <eric.auger@redhat.com>
Cc: <stable@vger.kernel.org>
Fixes: 57f972e2b3 ("vfio/platform: trigger an interrupt via eventfd")
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20240308230557.805580-7-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 18c198c96a ]
A vulnerability exists where the eventfd for INTx signaling can be
deconfigured, which unregisters the IRQ handler but still allows
eventfds to be signaled with a NULL context through the SET_IRQS ioctl
or through unmask irqfd if the device interrupt is pending.
Ideally this could be solved with some additional locking; the igate
mutex serializes the ioctl and config space accesses, and the interrupt
handler is unregistered relative to the trigger, but the irqfd path
runs asynchronous to those. The igate mutex cannot be acquired from the
atomic context of the eventfd wake function. Disabling the irqfd
relative to the eventfd registration is potentially incompatible with
existing userspace.
As a result, the solution implemented here moves configuration of the
INTx interrupt handler to track the lifetime of the INTx context object
and irq_type configuration, rather than registration of a particular
trigger eventfd. Synchronization is added between the ioctl path and
eventfd_signal() wrapper such that the eventfd trigger can be
dynamically updated relative to in-flight interrupts or irqfd callbacks.
Cc: <stable@vger.kernel.org>
Fixes: 89e1f7d4c6 ("vfio: Add PCI device driver")
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20240308230557.805580-5-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b620ecbd17 ]
In order to synchronize changes that can affect the thread callback,
introduce an interface to force a flush of the inject workqueue. The
irqfd pointer is only valid under spinlock, but the workqueue cannot
be flushed under spinlock. Therefore the flush work for the irqfd is
queued under spinlock. The vfio_irqfd_cleanup_wq workqueue is re-used
for queuing this work such that flushing the workqueue is also ordered
relative to shutdown.
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20240308230557.805580-4-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fe9a708268 ]
Currently for devices requiring masking at the irqchip for INTx, ie.
devices without DisINTx support, the IRQ is enabled in request_irq()
and subsequently disabled as necessary to align with the masked status
flag. This presents a window where the interrupt could fire between
these events, resulting in the IRQ incrementing the disable depth twice.
This would be unrecoverable for a user since the masked flag prevents
nested enables through vfio.
Instead, invert the logic using IRQF_NO_AUTOEN such that exclusive INTx
is never auto-enabled, then unmask as required.
Cc: <stable@vger.kernel.org>
Fixes: 89e1f7d4c6 ("vfio: Add PCI device driver")
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20240308230557.805580-2-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45bcc03465 upstream.
The test counter 'test_cnt' should not be returned in diag.sh, e.g. what
if only the 4th test fail? Will do 'exit 4' which is 'exit ${KSFT_SKIP}',
the whole test will be marked as skipped instead of 'failed'!
So we should do ret=${KSFT_FAIL} instead.
Fixes: df62f2ec3d ("selftests/mptcp: add diag interface tests")
Cc: stable@vger.kernel.org
Fixes: 42fb6cddec ("selftests: mptcp: more stable diag tests")
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5c0ca1365 upstream.
Chuck reported [1] an IO hang problem on NFS exports that reside on SATA
devices and bisected to commit 615939a2ae ("blk-mq: defer to the normal
submission path for post-flush requests").
We analysed the IO hang problem, found there are two postflush requests
waiting for each other.
The first postflush request completed the REQ_FSEQ_DATA sequence, so go to
the REQ_FSEQ_POSTFLUSH sequence and added in the flush pending list, but
failed to blk_kick_flush() because of the second postflush request which
is inflight waiting in scheduler queue.
The second postflush waiting in scheduler queue can't be dispatched because
the first postflush hasn't released scheduler resource even though it has
completed by itself.
Fix it by releasing scheduler resource when the first postflush request
completed, so the second postflush can be dispatched and completed, then
make blk_kick_flush() succeed.
While at it, remove the check for e->ops.finish_request, as all
schedulers set that. Reaffirm this requirement by adding a WARN_ON_ONCE()
at scheduler registration time, just like we do for insert_requests and
dispatch_request.
[1] https://lore.kernel.org/all/7A57C7AE-A51A-4254-888B-FE15CA21F9E9@oracle.com/
Link: https://lore.kernel.org/linux-block/20230819031206.2744005-1-chengming.zhou@linux.dev/
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202308172100.8ce4b853-oliver.sang@intel.com
Fixes: 615939a2ae ("blk-mq: defer to the normal submission path for post-flush requests")
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Link: https://lore.kernel.org/r/20230813152325.3017343-1-chengming.zhou@linux.dev
[axboe: folded in incremental fix and added tags]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
[bvanassche: changed RQF_USE_SCHED into RQF_ELVPRIV; restored the
finish_request pointer check before calling finish_request and removed
the new warning from the elevator code. This patch fixes an I/O hang
when submitting a REQ_FUA request to a request queue for a zoned block
device for which FUA has been disabled (QUEUE_FLAG_FUA is not set).]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38b43539d6 upstream.
Fix an incorrect number of pages being released for buffers that do not
start at the beginning of a page.
Fixes: 1b151e2435 ("block: Remove special-casing of compound pages")
Cc: stable@vger.kernel.org
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Tested-by: Greg Edwards <gedwards@ddn.com>
Link: https://lore.kernel.org/r/86e592a9-98d4-4cff-a646-0c0084328356@cybernetics.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
[ Tony: backport to v6.1 by replacing bio_release_page() loop with
folio_put_refs() as commits fd363244e8 and e4cc64657b are not
present. ]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 672448ccf9 upstream.
When about to transmit the function imx_uart_start_tx is called and in
some RS485 configurations this function will call imx_uart_stop_rx. The
problem is that imx_uart_stop_rx will enable loopback in order to
release the RS485 bus, but when loopback is enabled transmitted data
will just be looped to RX.
This patch fixes the above problem by not enabling loopback when about
to transmit.
This driver now works well when used for RS485 half duplex master
configurations.
Fixes: 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal active high")
Cc: stable <stable@kernel.org>
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20240221115304.509811-1-rickaran@axis.com
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9eb05877db ]
22e8e19 has introduced a regression in the imgchip->pwm_clk lookup, whereas
the clock name has also been renamed to "imgchip". This causes the driver
failing to load:
[ 0.546905] img-pwm 18101300.pwm: failed to get imgchip clock
[ 0.553418] img-pwm: probe of 18101300.pwm failed with error -2
Fix this lookup by reverting the clock name back to "pwm".
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Link: https://lore.kernel.org/r/20240320083602.81592-1-wigyori@uid0.hu
Fixes: 22e8e19a46 ("pwm: img: Rename variable pointing to driver private data")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62b71cd73d ]
Check if get_next_variable() is actually valid pointer before
calling it. In kdump kernel this method is set to NULL that causes
panic during the kexec-ed kernel boot.
Tested with QEMU and OVMF firmware.
Fixes: bad267f9e1 ("efi: verify that variable services are supported")
Signed-off-by: Oleksandr Tymoshenko <ovt@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10e4b5166d ]
Commit 672365477a ("x86/fpu: Update XFD state where required") and
commit 8bf26758ca ("x86/fpu: Add XFD state to fpstate") introduced a
per CPU variable xfd_state to keep the MSR_IA32_XFD value cached, in
order to avoid unnecessary writes to the MSR.
On CPU hotplug MSR_IA32_XFD is reset to the init_fpstate.xfd, which
wipes out any stale state. But the per CPU cached xfd value is not
reset, which brings them out of sync.
As a consequence a subsequent xfd_update_state() might fail to update
the MSR which in turn can result in XRSTOR raising a #NM in kernel
space, which crashes the kernel.
To fix this, introduce xfd_set_state() to write xfd_state together
with MSR_IA32_XFD, and use it in all places that set MSR_IA32_XFD.
Fixes: 672365477a ("x86/fpu: Update XFD state where required")
Signed-off-by: Adamos Ttofari <attofari@amazon.de>
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240322230439.456571-1-chang.seok.bae@intel.com
Closes: https://lore.kernel.org/lkml/20230511152818.13839-1-attofari@amazon.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cb4a48275 ]
Following warning is sometimes observed while booting my servers:
[ 3.594838] DMA: preallocated 4096 KiB GFP_KERNEL pool for atomic allocations
[ 3.602918] swapper/0: page allocation failure: order:10, mode:0xcc1(GFP_KERNEL|GFP_DMA), nodemask=(null),cpuset=/,mems_allowed=0-1
...
[ 3.851862] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocation
If 'nokaslr' boot option is set, the warning always happens.
On x86, ZONE_DMA is small zone at the first 16MB of physical address
space. When this problem happens, most of that space seems to be used by
decompressed kernel. Thereby, there is not enough space at DMA_ZONE to
meet the request of DMA pool allocation.
The commit 2f77465b05 ("x86/efistub: Avoid placing the kernel below
LOAD_PHYSICAL_ADDR") tried to fix this problem by introducing lower
bound of allocation.
But the fix is not complete.
efi_random_alloc() allocates pages by following steps.
1. Count total available slots ('total_slots')
2. Select a slot ('target_slot') to allocate randomly
3. Calculate a starting address ('target') to be included target_slot
4. Allocate pages, which starting address is 'target'
In step 1, 'alloc_min' is used to offset the starting address of memory
chunk. But in step 3 'alloc_min' is not considered at all. As the
result, 'target' can be miscalculated and become lower than 'alloc_min'.
When KASLR is disabled, 'target_slot' is always 0 and the problem
happens everytime if the EFI memory map of the system meets the
condition.
Fix this problem by calculating 'target' considering 'alloc_min'.
Cc: linux-efi@vger.kernel.org
Cc: Tom Englund <tomenglund26@gmail.com>
Cc: linux-kernel@vger.kernel.org
Fixes: 2f77465b05 ("x86/efistub: Avoid placing the kernel below LOAD_PHYSICAL_ADDR")
Signed-off-by: Kazuma Kondo <kazuma-kondo@nec.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e51653d5d ]
Read from an unsafe address with copy_from_kernel_nofault() in
arch_adjust_kprobe_addr() because this function is used before checking
the address is in text or not. Syzcaller bot found a bug and reported
the case if user specifies inaccessible data area,
arch_adjust_kprobe_addr() will cause a kernel panic.
[ mingo: Clarified the comment. ]
Fixes: cc66bb9145 ("x86/ibt,kprobes: Cure sym+0 equals fentry woes")
Reported-by: Qiang Zhang <zzqq0103.hey@gmail.com>
Tested-by: Jinghao Jia <jinghao7@illinois.edu>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/171042945004.154897.2221804961882915806.stgit@devnote2
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 853a603030 ]
RZ/G2L interrupt chips require that the interrupt is masked before changing
the NMI, IRQ, TINT interrupt settings. Aside of that, after setting an edge
trigger type it is required to clear the interrupt status register in order
to avoid spurious interrupts.
The current implementation fails to do either of that and therefore is
prone to generate spurious interrupts when setting the trigger type.
Address this by:
- Ensuring that the interrupt is masked at the chip level across the
update for the TINT chip
- Clearing the interrupt status register after updating the trigger mode
for edge type interrupts
[ tglx: Massaged changelog and reverted the spin_lock_irqsave() change as
the set_type() callback is always called with interrupts disabled. ]
Fixes: 3fed09559c ("irqchip: Add RZ/G2L IA55 Interrupt Controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2eca4731cc ]
There are 2 TITSR registers available on the IA55 interrupt controller.
Add a macro that retrieves the TITSR register offset based on it's
index. This macro is useful in when adding suspend/resume support so both
TITSR registers can be accessed in a for loop.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20231120111820.87398-7-claudiu.beznea.uj@bp.renesas.com
Stable-dep-of: 853a603030 ("irqchip/renesas-rzg2l: Prevent spurious interrupts when setting trigger type")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9eec61df55 ]
The irq_eoi() callback of the RZ/G2L interrupt chip clears the relevant
interrupt cause bit in the TSCR register by writing to it.
This write is not sufficient because the write is posted and therefore not
guaranteed to immediately clear the bit. Due to that delay the CPU can
raise the just handled interrupt again.
Prevent this by reading the register back which causes the posted write to
be flushed to the hardware before the read completes.
Fixes: 3fed09559c ("irqchip: Add RZ/G2L IA55 Interrupt Controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef88eefb1a ]
The RZ/G2L manual (chapter "IRQ Status Control Register (ISCR)") describes
the operation to clear interrupts through the ISCR register as follows:
[Write operation]
When "Falling-edge detection", "Rising-edge detection" or
"Falling/Rising-edge detection" is set in IITSR:
- In case ISTAT is 1
0: IRQn interrupt detection status is cleared.
1: Invalid to write.
- In case ISTAT is 0
Invalid to write.
When "Low-level detection" is set in IITSR.:
Invalid to write.
Take the interrupt type into account when clearing interrupts through the
ISCR register to avoid writing the ISCR when the interrupt type is level.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231120111820.87398-6-claudiu.beznea.uj@bp.renesas.com
Stable-dep-of: 9eec61df55 ("irqchip/renesas-rzg2l: Flush posted write in irq_eoi()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afc5aa46ed ]
The swiotlb does not support a mapping size > swiotlb_max_mapping_size().
On the other hand, with a 64KB PAGE_SIZE configuration, it's observed that
an NVME device can map a size between 300KB~512KB, which certainly failed
the swiotlb mappings, though the default pool of swiotlb has many slots:
systemd[1]: Started Journal Service.
=> nvme 0000:00:01.0: swiotlb buffer is full (sz: 327680 bytes), total 32768 (slots), used 32 (slots)
note: journal-offline[392] exited with irqs disabled
note: journal-offline[392] exited with preempt_count 1
Call trace:
[ 3.099918] swiotlb_tbl_map_single+0x214/0x240
[ 3.099921] iommu_dma_map_page+0x218/0x328
[ 3.099928] dma_map_page_attrs+0x2e8/0x3a0
[ 3.101985] nvme_prep_rq.part.0+0x408/0x878 [nvme]
[ 3.102308] nvme_queue_rqs+0xc0/0x300 [nvme]
[ 3.102313] blk_mq_flush_plug_list.part.0+0x57c/0x600
[ 3.102321] blk_add_rq_to_plug+0x180/0x2a0
[ 3.102323] blk_mq_submit_bio+0x4c8/0x6b8
[ 3.103463] __submit_bio+0x44/0x220
[ 3.103468] submit_bio_noacct_nocheck+0x2b8/0x360
[ 3.103470] submit_bio_noacct+0x180/0x6c8
[ 3.103471] submit_bio+0x34/0x130
[ 3.103473] ext4_bio_write_folio+0x5a4/0x8c8
[ 3.104766] mpage_submit_folio+0xa0/0x100
[ 3.104769] mpage_map_and_submit_buffers+0x1a4/0x400
[ 3.104771] ext4_do_writepages+0x6a0/0xd78
[ 3.105615] ext4_writepages+0x80/0x118
[ 3.105616] do_writepages+0x90/0x1e8
[ 3.105619] filemap_fdatawrite_wbc+0x94/0xe0
[ 3.105622] __filemap_fdatawrite_range+0x68/0xb8
[ 3.106656] file_write_and_wait_range+0x84/0x120
[ 3.106658] ext4_sync_file+0x7c/0x4c0
[ 3.106660] vfs_fsync_range+0x3c/0xa8
[ 3.106663] do_fsync+0x44/0xc0
Since untrusted devices might go down the swiotlb pathway with dma-iommu,
these devices should not map a size larger than swiotlb_max_mapping_size.
To fix this bug, add iommu_dma_max_mapping_size() for untrusted devices to
take into account swiotlb_max_mapping_size() v.s. iova_rcache_range() from
the iommu_dma_opt_mapping_size().
Fixes: 82612d66d5 ("iommu: Allow the dma-iommu api to use bounce buffers")
Link: https://lore.kernel.org/r/ee51a3a5c32cf885b18f6416171802669f4a718a.1707851466.git.nicolinc@nvidia.com
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
[will: Drop redundant is_swiotlb_active(dev) check]
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51b30ecb73 ]
Nicolin reports that swiotlb buffer allocations fail for an NVME device
behind an IOMMU using 64KiB pages. This is because we end up with a
minimum allocation alignment of 64KiB (for the IOMMU to map the buffer
safely) but a minimum DMA alignment mask corresponding to a 4KiB NVME
page (i.e. preserving the 4KiB page offset from the original allocation).
If the original address is not 4KiB-aligned, the allocation will fail
because swiotlb_search_pool_area() erroneously compares these unmasked
bits with the 64KiB-aligned candidate allocation.
Tweak swiotlb_search_pool_area() so that the DMA alignment mask is
reduced based on the required alignment of the allocation.
Fixes: 82612d66d5 ("iommu: Allow the dma-iommu api to use bounce buffers")
Link: https://lore.kernel.org/r/cover.1707851466.git.nicolinc@nvidia.com
Reported-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80fcac5538 ]
Patch series "minmax: Relax type checks in min() and max()", v4.
The min() (etc) functions in minmax.h require that the arguments have
exactly the same types.
However when the type check fails, rather than look at the types and fix
the type of a variable/constant, everyone seems to jump on min_t(). In
reality min_t() ought to be rare - when something unusual is being done,
not normality.
The orginal min() (added in 2.4.9) replaced several inline functions and
included the type - so matched the implicit casting of the function call.
This was renamed min_t() in 2.4.10 and the current min() added. There is
no actual indication that the conversion of negatve values to large
unsigned values has ever been an actual problem.
A quick grep shows 5734 min() and 4597 min_t(). Having the casts on
almost half of the calls shows that something is clearly wrong.
If the wrong type is picked (and it is far too easy to pick the type of
the result instead of the larger input) then significant bits can get
discarded.
Pretty much the worst example is in the derived clamp_val(), consider:
unsigned char x = 200u;
y = clamp_val(x, 10u, 300u);
I also suspect that many of the min_t(u16, ...) are actually wrong. For
example copy_data() in printk_ringbuffer.c contains:
data_size = min_t(u16, buf_size, len);
Here buf_size is 'unsigned int' and len 'u16', pass a 64k buffer (can you
prove that doesn't happen?) and no data is returned. Apparantly it did -
and has since been fixed.
The only reason that most of the min_t() are 'fine' is that pretty much
all the values in the kernel are between 0 and INT_MAX.
Patch 1 adds umin(), this uses integer promotions to convert both
arguments to 'unsigned long long'. It can be used to compare a signed
type that is known to contain a non-negative value with an unsigned type.
The compiler typically optimises it all away. Added first so that it can
be referred to in patch 2.
Patch 2 replaces the 'same type' check with a 'same signedness' one. This
makes min(unsigned_int_var, sizeof()) be ok. The error message is also
improved and will contain the expanded form of both arguments (useful for
seeing how constants are defined).
Patch 3 just fixes some whitespace.
Patch 4 allows comparisons of 'unsigned char' and 'unsigned short' to
signed types. The integer promotion rules convert them both to 'signed
int' prior to the comparison so they can never cause a negative value be
converted to a large positive one.
Patch 5 (rewritted for v4) allows comparisons of unsigned values against
non-negative constant integer expressions. This makes
min(unsigned_int_var, 4) be ok.
The only common case that is still errored is the comparison of signed
values against unsigned constant integer expressions below __INT_MAX__.
Typcally min(int_val, sizeof (foo)), the real fix for this is casting the
constant: min(int_var, (int)sizeof (foo)).
With all the patches applied pretty much all the min_t() could be replaced
by min(), and most of the rest by umin(). However they all need careful
inspection due to code like:
sz = min_t(unsigned char, sz - 1, LIM - 1) + 1;
which converts 0 to LIM.
This patch (of 6):
umin() and umax() can be used when min()/max() errors a signed v unsigned
compare when the signed value is known to be non-negative.
Unlike min_t(some_unsigned_type, a, b) umin() will never mask off high
bits if an inappropriate type is selected.
The '+ 0u + 0ul + 0ull' may look strange.
The '+ 0u' is needed for 'signed int' on 64bit systems.
The '+ 0ul' is needed for 'signed long' on 32bit systems.
The '+ 0ull' is needed for 'signed long long'.
Link: https://lkml.kernel.org/r/b97faef60ad24922b530241c5d7c933c@AcuMS.aculab.com
Link: https://lkml.kernel.org/r/41d93ca827a248698ec64bf57e0c05a5@AcuMS.aculab.com
Signed-off-by: David Laight <david.laight@aculab.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: 51b30ecb73 ("swiotlb: Fix alignment checks when both allocation and DMA masks are present")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb13b11d53 ]
When a probe is registered at the trace_sys_enter() tracepoint, and that
probe changes the system call number, the old system call still gets
executed. This worked correctly until commit b6ec413461 ("core/entry:
Report syscall correctly for trace and audit"), which removed the
re-evaluation of the syscall number after the trace point.
Restore the original semantics by re-evaluating the system call number
after trace_sys_enter().
The performance impact of this re-evaluation is minimal because it only
takes place when a trace point is active, and compared to the actual trace
point overhead the read from a cache hot variable is negligible.
Fixes: b6ec413461 ("core/entry: Report syscall correctly for trace and audit")
Signed-off-by: André Rösti <an.roesti@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240311211704.7262-1-an.roesti@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b34b9547ce ]
The prescaler in the "Global Timer Control Register bit assignments" is
documented to use bits [15:8], which means that the maximum prescaler
register value is 0xff.
Fixes: 171b45a4a7 ("clocksource/drivers/arm_global_timer: Implement rate compensation whenever source clock changes")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240218174138.1942418-2-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
This fix is applicable for LTS kernel, 6.1.y. In latest kernels, this race
issue is fixed by the patch series [1] and [2]. The right thing to do here
would have been propagating these changes from latest kernel to the stable
branch, 6.1.y. However, these changes seems too intrusive to be picked for
stable branches. Hence, the fix proposed can be taken as an alternative
instead of backporting the patch series.
[1] https://lore.kernel.org/all/0-v8-81230027b2fa+9d-iommu_all_defdom_jgg@nvidia.com/
[2] https://lore.kernel.org/all/0-v5-1b99ae392328+44574-iommu_err_unwind_jgg@nvidia.com/
Issue:
A race condition is observed when arm_smmu_device_probe and
modprobe of client devices happens in parallel. This results
in the allocation of a new default domain for the iommu group
even though it was previously allocated and the respective iova
domain(iovad) was initialized. However, for this newly allocated
default domain, iovad will not be initialized. As a result, for
devices requesting dma allocations, this uninitialized iovad will
be used, thereby causing NULL pointer dereference issue.
Flow:
- During arm_smmu_device_probe, bus_iommu_probe() will be called
as part of iommu_device_register(). This results in the device probe,
__iommu_probe_device().
- When the modprobe of the client device happens in parallel, it
sets up the DMA configuration for the device using of_dma_configure_id(),
which inturn calls iommu_probe_device(). Later, default domain is
allocated and attached using iommu_alloc_default_domain() and
__iommu_attach_device() respectively. It then ends up initializing a
mapping domain(IOVA domain) and rcaches for the device via
arch_setup_dma_ops()->iommu_setup_dma_ops().
- Now, in the bus_iommu_probe() path, it again tries to allocate
a default domain via probe_alloc_default_domain(). This results in
allocating a new default domain(along with IOVA domain) via
__iommu_domain_alloc(). However, this newly allocated IOVA domain
will not be initialized.
- Now, when the same client device tries dma allocations via
iommu_dma_alloc(), it ends up accessing the rcaches of the newly
allocated IOVA domain, which is not initialized. This results
into NULL pointer dereferencing.
Fix this issue by adding a check in probe_alloc_default_domain()
to see if the iommu_group already has a default domain allocated
and initialized.
Cc: <stable@vger.kernel.org> # see patch description, fix applicable only for 6.1.y
Signed-off-by: Charan Teja Kalla <quic_charante@quicinc.com>
Co-developed-by: Nikhil V <quic_nprakash@quicinc.com>
Signed-off-by: Nikhil V <quic_nprakash@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 861b3415e4 upstream.
This reverts commit ed00a6945d,
which added a quirk entry to enable the Yellow Carp (YC)
driver for the Lenovo 21J2 laptop.
Although the microphone functioned with the YC driver, it
resulted in incorrect driver usage. The Lenovo 21J2 is not a
Yellow Carp platform, but a Pink Sardine platform, which
already has an upstreamed driver.
The microphone on the Lenovo 21J2 operates correctly with the
CONFIG_SND_SOC_AMD_PS flag enabled and does not require the
quirk entry. So this patch removes the quirk entry.
Thanks to Mukunda Vijendar [1] for pointing this out.
Link: https://lore.kernel.org/linux-sound/023092e1-689c-4b00-b93f-4092c3724fb6@amd.com/ [1]
Signed-off-by: Jiawei Wang <me@jwang.link>
Link: https://lore.kernel.org/linux-sound/023092e1-689c-4b00-b93f-4092c3724fb6@amd.com/ [1]
Link: https://msgid.link/r/20240313015853.3573242-2-me@jwang.link
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Luca Stefani <luca.stefani.ge1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8590541473 upstream.
Since we're setting the CRYPTO_TFM_REQ_MAY_BACKLOG flag on our
requests to the crypto API, crypto_aead_{encrypt,decrypt} can return
-EBUSY instead of -EINPROGRESS in valid situations. For example, when
the cryptd queue for AESNI is full (easy to trigger with an
artificially low cryptd.cryptd_max_cpu_qlen), requests will be enqueued
to the backlog but still processed. In that case, the async callback
will also be called twice: first with err == -EINPROGRESS, which it
seems we can just ignore, then with err == 0.
Compared to Sabrina's original patch this version uses the new
tls_*crypt_async_wait() helpers and converts the EBUSY to
EINPROGRESS to avoid having to modify all the error handling
paths. The handling is identical.
Fixes: a54667f672 ("tls: Add support for encryption using async offload accelerator")
Fixes: 94524d8fc9 ("net/tls: Add support for async decryption of tls records")
Co-developed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/netdev/9681d1febfec295449a62300938ed2ae66983f28.1694018970.git.sd@queasysnail.net/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Srish: v2: fixed hunk failures
fixed merge-conflict in stable branch linux-6.1.y,
needs to go on top of https://lore.kernel.org/stable/20240307155930.913525-1-lee@kernel.org/]
Signed-off-by: Srish Srinivasan <srish.srinivasan@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cefcd4fe2e upstream.
Normally, the EFI stub calls into the EFI boot services using the stack
that was live when the stub was entered. According to the UEFI spec,
this stack needs to be at least 128k in size - this might seem large but
all asynchronous processing and event handling in EFI runs from the same
stack and so quite a lot of space may be used in practice.
In mixed mode, the situation is a bit different: the bootloader calls
the 32-bit EFI stub entry point, which calls the decompressor's 32-bit
entry point, where the boot stack is set up, using a fixed allocation
of 16k. This stack is still in use when the EFI stub is started in
64-bit mode, and so all calls back into the EFI firmware will be using
the decompressor's limited boot stack.
Due to the placement of the boot stack right after the boot heap, any
stack overruns have gone unnoticed. However, commit
5c4feadb00 ("x86/decompressor: Move global symbol references to C code")
moved the definition of the boot heap into C code, and now the boot
stack is placed right at the base of BSS, where any overruns will
corrupt the end of the .data section.
While it would be possible to work around this by increasing the size of
the boot stack, doing so would affect all x86 systems, and mixed mode
systems are a tiny (and shrinking) fraction of the x86 installed base.
So instead, record the firmware stack pointer value when entering from
the 32-bit firmware, and switch to this stack every time a EFI boot
service call is made.
Cc: <stable@kernel.org> # v6.1+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 937844d661 upstream.
Need to check the offset bits for values greater than 255.
v2: also update amdgpu_dm_connector values.
Suggested-by: Mano Ségransan <mano.segransan@protonmail.com>
Tested-by: Mano Ségransan <mano.segransan@protonmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3203
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ceb013b2d9 upstream.
If registering the platform device fails, the lookup table is
removed in the error path. On module removal we would try to
remove the lookup table again. Fix this by setting priv->lookup
only if registering the platform device was successful.
In addition free the memory allocated for the lookup table in
the error path.
Fixes: d308dfbf62 ("i2c: mux/i801: Switch to use descriptor passing")
Cc: stable@vger.kernel.org
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Damien Le Moal