This patch removes the support of RFC5827 early retransmit (i.e.,
fast recovery on small inflight with <3 dupacks) because it is
subsumed by the new RACK loss detection. More specifically when
RACK receives DUPACKs, it'll arm a reordering timer to start fast
recovery after a quarter of (min)RTT, hence it covers the early
retransmit except RACK does not limit itself to specific inflight
or dupack numbers.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes two things:
1. Start fast recovery with RACK in addition to other heuristics
(e.g., DUPACK threshold, FACK). Prior to this change RACK
is enabled to detect losses only after the recovery has
started by other algorithms.
2. Disable TCP early retransmit. RACK subsumes the early retransmit
with the new reordering timer feature. A latter patch in this
series removes the early retransmit code.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packets inside a jumbo skb (e.g., TSO) share the same skb
timestamp, even though they are sent sequentially on the wire. Since
RACK is based on time, it can not detect some packets inside the
same skb are lost. However, we can leverage the packet sequence
numbers as extended timestamps to detect losses. Therefore, when
RACK timestamp is identical to skb's timestamp (i.e., one of the
packets of the skb is acked or sacked), we use the sequence numbers
of the acked and unacked packets to break ties.
We can use the same sequence logic to advance RACK xmit time as
well to detect more losses and avoid timeout.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes RACK install a reordering timer when it suspects
some packets might be lost, but wants to delay the decision
a little bit to accomodate reordering.
It does not create a new timer but instead repurposes the existing
RTO timer, because both are meant to retransmit packets.
Specifically it arms a timer ICSK_TIME_REO_TIMEOUT when
the RACK timing check fails. The wait time is set to
RACK.RTT + RACK.reo_wnd - (NOW - Packet.xmit_time) + fudge
This translates to expecting a packet (Packet) should take
(RACK.RTT + RACK.reo_wnd + fudge) to deliver after it was sent.
When there are multiple packets that need a timer, we use one timer
with the maximum timeout. Therefore the timer conservatively uses
the maximum window to expire N packets by one timeout, instead of
N timeouts to expire N packets sent at different times.
The fudge factor is 2 jiffies to ensure when the timer fires, all
the suspected packets would exceed the deadline and be marked lost
by tcp_rack_detect_loss(). It has to be at least 1 jiffy because the
clock may tick between calling icsk_reset_xmit_timer(timeout) and
actually hang the timer. The next jiffy is to lower-bound the timeout
to 2 jiffies when reo_wnd is < 1ms.
When the reordering timer fires (tcp_rack_reo_timeout): If we aren't
in Recovery we'll enter fast recovery and force fast retransmit.
This is very similar to the early retransmit (RFC5827) except RACK
is not constrained to only enter recovery for small outstanding
flights.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Record the most recent RTT in RACK. It is often identical to the
"ca_rtt_us" values in tcp_clean_rtx_queue. But when the packet has
been retransmitted, RACK choses to believe the ACK is for the
(latest) retransmitted packet if the RTT is over minimum RTT.
This requires passing the arrival time of the most recent ACK to
RACK routines. The timestamp is now recorded in the "ack_time"
in tcp_sacktag_state during the ACK processing.
This patch does not change the RACK algorithm itself. It only adds
the RTT variable to prepare the next main patch.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new helper tcp_rack_detect_loss to prepare the upcoming
RACK reordering timer patch.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function documentation for cfg80211_connect_bss() and
cfg80211_connect_result() was still claiming that they are used only for
a success case while these functions can now be used to report both
success and various failure cases. The actual use cases were already
described in the connect() documentation.
Update the function specific comments to note the failure cases and also
describe how the special status == -1 case is used in
cfg80211_connect_bss() to indicate a connection timeout based on the
internal implementation in cfg80211_connect_timeout().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[use tabs for indentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enhances the connect timeout API to also carry the reason for the
timeout. These reason codes for the connect time out are represented by
enum nl80211_timeout_reason and are passed to user space through a new
attribute NL80211_ATTR_TIMEOUT_REASON (u32).
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[keep gfp_t argument last]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enhance sched scan to support option of finding a better BSS while in
connected state. Firmware scans the medium and reports when it finds a
known BSS which has better RSSI than the current connected BSS. New
attributes to specify the relative RSSI (compared to the current BSS)
are added to the sched scan to implement this.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With 78, 111 and 85 bytes respectively (on x86-64), the
functions iwe_stream_add_event(), iwe_stream_add_point()
and iwe_stream_add_value() really shouldn't be inlines.
It appears that at least my compiler already decided
the same, and created a single instance of each one
of them for each file using it, but that's still a
number of instances in the system overall, which this
reduces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a flag that indicates that the WEP ICV was stripped from an
RX packet, allowing the device to not transfer that if it's
already checked.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
gcc-7 complains that wl3501_cs passes NULL into a function that
then uses the argument as the input for memcpy:
drivers/net/wireless/wl3501_cs.c: In function 'wl3501_get_scan':
include/net/iw_handler.h:559:3: error: argument 2 null where non-null expected [-Werror=nonnull]
memcpy(stream + point_len, extra, iwe->u.data.length);
This works fine here because iwe->u.data.length is guaranteed to be 0
and the memcpy doesn't actually have an effect.
Making the length check explicit avoids the warning and should have
no other effect here.
Also check the pointer itself, since otherwise we get warnings
elsewhere in the code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow dissection of (R)ARP operation hardware and protocol addresses
for Ethernet hardware and IPv4 protocol addresses.
There are currently no users of FLOW_DISSECTOR_KEY_ARP.
A follow-up patch will allow FLOW_DISSECTOR_KEY_ARP to be used by the
flower classifier.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm_init_tempstate is always called from within rcu read side section.
We can thus use a simpler function that doesn't call rcu_read_lock
again.
While at it, also make xfrm_init_tempstate return value void, the
return value was never tested.
A followup patch will replace remaining callers of xfrm_state_get_afinfo
with xfrm_state_afinfo_get_rcu variant and then remove the 'old'
get_afinfo interface.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Support for SMC socket monitoring via netlink sockets of protocol
NETLINK_SOCK_DIAG.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Direct call of tcp_set_keepalive() function from protocol-agnostic
sock_setsockopt() function in net/core/sock.c violates network
layering. And newly introduced protocol (SMC-R) will need its own
keepalive function. Therefore, add "keepalive" function pointer
to "struct proto", and call it from sock_setsockopt() via this pointer.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have properly encapsulated and made drivers utilize exported
functions, we can switch dsa_switch_ops to be a annotated with const.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for making struct dsa_switch_ops const, encapsulate it
within a dsa_switch_driver which has a list pointer and a pointer to
dsa_switch_ops. This allows us to take the list_head pointer out of
dsa_switch_ops, which is written to by {un,}register_switch_driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disconnect or deauthenticate when the owning socket is closed if this
flag is supplied to CMD_CONNECT or CMD_ASSOCIATE. This may be used
to ensure userspace daemon doesn't leave an unmanaged connection behind.
In some situations it would be possible to account for that, to some
degree, in the deamon restart code or in the up/down scripts without
the use of this attribute. But there will be systems where the daemon
can go away for varying periods without a warning due to local resource
management.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The tc_from field fulfills two roles. It encodes whether a packet was
redirected by an act_mirred device and, if so, whether act_mirred was
called on ingress or egress. Split it into separate fields.
The information is needed by the special IFB loop, where packets are
taken out of the normal path by act_mirred, forwarded to IFB, then
reinjected at their original location (ingress or egress) by IFB.
The IFB device cannot use skb->tc_at_ingress, because that may have
been overwritten as the packet travels from act_mirred to ifb_xmit,
when it passes through tc_classify on the IFB egress path. Cache this
value in skb->tc_from_ingress.
That field is valid only if a packet arriving at ifb_xmit came from
act_mirred. Other packets can be crafted to reach ifb_xmit. These
must be dropped. Set tc_redirected on redirection and drop all packets
that do not have this bit set.
Both fields are set only on cloned skbs in tc actions, so original
packet sources do not have to clear the bit when reusing packets
(notably, pktgen and octeon).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Field tc_at is used only within tc actions to distinguish ingress from
egress processing. A single bit is sufficient for this purpose.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the remaining two fields from tc_verd and remove the __u16
completely. TC_AT and TC_FROM are converted to equivalent two-bit
integer fields tc_at and tc_from. Where possible, use existing
helper skb_at_tc_ingress when reading tc_at. Introduce helper
skb_reset_tc to clear fields.
Not documenting tc_from and tc_at, because they will be replaced
with single bit fields in follow-on patches.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets sent by the IFB device skip subsequent tc classification.
A single bit governs this state. Move it out of tc_verd in
anticipation of removing that __u16 completely.
The new bitfield tc_skip_classify temporarily uses one bit of a
hole, until tc_verd is removed completely in a follow-up patch.
Remove the bit hole comment. It could be 2, 3, 4 or 5 bits long.
With that many options, little value in documenting it.
Introduce a helper function to deduplicate the logic in the two
sites that check this bit.
The field tc_skip_classify is set only in IFB on skbs cloned in
act_mirred, so original packet sources do not have to clear the
bit when reusing packets (notably, pktgen and octeon).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp stream reconf, described in RFC 6525, needs a structure to
save per stream information in assoc, like stream state.
In the future, sctp stream scheduler also needs it to save some
stream scheduler params and queues.
This patchset is to prepare the stream array in assoc for stream
reconf. It defines sctp_stream that includes stream arrays inside
to replace ssnmap.
Note that we use different structures for IN and OUT streams, as
the members in per OUT stream will get more and more different
from per IN stream.
v1->v2:
- put these patches into a smaller group.
v2->v3:
- define sctp_stream to contain stream arrays, and create stream.c
to put stream-related functions.
- merge 3 patches into 1, as new sctp_stream has the same name
with before.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_select_default has a single caller within the same file.
Make it static.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a helper for reading that new property and applying
limitations of supported channels specified this way.
It is used with devices that normally support a wide wireless band but
in a given config are limited to some part of it (usually due to board
design). For example a dual-band chipset may be able to support one band
only because of used antennas.
It's also common that tri-band routers have separated radios for lower
and higher part of 5 GHz band and it may be impossible to say which is
which without a DT info.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
[add new function to documentation, fix link]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
udplite was copied from udp, they are virtually 100% identical.
This adds udplite tracker to udp instead, removes udplite module,
and then makes the udplite tracker builtin.
udplite will then simply re-use udp timeout settings.
It makes little sense to add separate sysctls, nowadays we have
fine-grained timeout policy support via the CT target.
old:
text data bss dec hex filename
1633 672 0 2305 901 nf_conntrack_proto_udp.o
1756 672 0 2428 97c nf_conntrack_proto_udplite.o
69526 17937 268 87731 156b3 nf_conntrack.ko
new:
text data bss dec hex filename
2442 1184 0 3626 e2a nf_conntrack_proto_udp.o
68565 17721 268 86554 1521a nf_conntrack.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Different namespace application might require different maximal
number of remembered connection requests.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespace application might require fast recycling
TIME-WAIT sockets independently of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to use this cascading. It doesn't add anything.
Let's remove it and simplify.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.
The most important is to not assume the packet is RX just because
the destination address matches that of the device. Such an
assumption causes problems when an interface is put into loopback
mode.
2) If we retry when creating a new tc entry (because we dropped the
RTNL mutex in order to load a module, for example) we end up with
-EAGAIN and then loop trying to replay the request. But we didn't
reset some state when looping back to the top like this, and if
another thread meanwhile inserted the same tc entry we were trying
to, we re-link it creating an enless loop in the tc chain. Fix from
Daniel Borkmann.
3) There are two different WRITE bits in the MDIO address register for
the stmmac chip, depending upon the chip variant. Due to a bug we
could set them both, fix from Hock Leong Kweh.
4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
r8169: add support for RTL8168 series add-on card.
net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
openvswitch: upcall: Fix vlan handling.
ipv4: Namespaceify tcp_tw_reuse knob
net: korina: Fix NAPI versus resources freeing
net, sched: fix soft lockup in tc_classify
net/mlx4_en: Fix user prio field in XDP forward
tipc: don't send FIN message from connectionless socket
ipvlan: fix multicast processing
ipvlan: fix various issues in ipvlan_process_multicast()
Different namespaces might have different requirements to reuse
TIME-WAIT sockets for new connections. This might be required in
cases where different namespace applications are in place which
require TIME_WAIT socket connections to be reduced independently
of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes and cleanups from David Miller:
1) Revert bogus nla_ok() change, from Alexey Dobriyan.
2) Various bpf validator fixes from Daniel Borkmann.
3) Add some necessary SET_NETDEV_DEV() calls to hsis_femac and hip04
drivers, from Dongpo Li.
4) Several ethtool ksettings conversions from Philippe Reynes.
5) Fix bugs in inet port management wrt. soreuseport, from Tom Herbert.
6) XDP support for virtio_net, from John Fastabend.
7) Fix NAT handling within a vrf, from David Ahern.
8) Endianness fixes in dpaa_eth driver, from Claudiu Manoil
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (63 commits)
net: mv643xx_eth: fix build failure
isdn: Constify some function parameters
mlxsw: spectrum: Mark split ports as such
cgroup: Fix CGROUP_BPF config
qed: fix old-style function definition
net: ipv6: check route protocol when deleting routes
r6040: move spinlock in r6040_close as SOFTIRQ-unsafe lock order detected
irda: w83977af_ir: cleanup an indent issue
net: sfc: use new api ethtool_{get|set}_link_ksettings
net: davicom: dm9000: use new api ethtool_{get|set}_link_ksettings
net: cirrus: ep93xx: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb3: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb2: use new api ethtool_{get|set}_link_ksettings
bpf: fix mark_reg_unknown_value for spilled regs on map value marking
bpf: fix overflow in prog accounting
bpf: dynamically allocate digest scratch buffer
gtp: Fix initialization of Flags octet in GTPv1 header
gtp: gtp_check_src_ms_ipv4() always return success
net/x25: use designated initializers
isdn: use designated initializers
...
A user may call listen with binding an explicit port with the intent
that the kernel will assign an available port to the socket. In this
case inet_csk_get_port does a port scan. For such sockets, the user may
also set soreuseport with the intent a creating more sockets for the
port that is selected. The problem is that the initial socket being
opened could inadvertently choose an existing and unreleated port
number that was already created with soreuseport.
This patch adds a boolean parameter to inet_bind_conflict that indicates
rather soreuseport is allowed for the check (in addition to
sk->sk_reuseport). In calls to inet_bind_conflict from inet_csk_get_port
the argument is set to true if an explicit port is being looked up (snum
argument is nonzero), and is false if port scan is done.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs updates from Al Viro:
- more ->d_init() stuff (work.dcache)
- pathname resolution cleanups (work.namei)
- a few missing iov_iter primitives - copy_from_iter_full() and
friends. Either copy the full requested amount, advance the iterator
and return true, or fail, return false and do _not_ advance the
iterator. Quite a few open-coded callers converted (and became more
readable and harder to fuck up that way) (work.iov_iter)
- several assorted patches, the big one being logfs removal
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
logfs: remove from tree
vfs: fix put_compat_statfs64() does not handle errors
namei: fold should_follow_link() with the step into not-followed link
namei: pass both WALK_GET and WALK_MORE to should_follow_link()
namei: invert WALK_PUT logics
namei: shift interpretation of LOOKUP_FOLLOW inside should_follow_link()
namei: saner calling conventions for mountpoint_last()
namei.c: get rid of user_path_parent()
switch getfrag callbacks to ..._full() primitives
make skb_add_data,{_nocache}() and skb_copy_to_page_nocache() advance only on success
[iov_iter] new primitives - copy_from_iter_full() and friends
don't open-code file_inode()
ceph: switch to use of ->d_init()
ceph: unify dentry_operations instances
lustre: switch to use of ->d_init()
Commit 4f7df337fe
"netlink: 2-clause nla_ok()" is BROKEN.
First clause tests if "->nla_len" could even be accessed at all,
it can not possibly be omitted.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment on the name indirection suggested an issue but turned out
to be untrue. Digging in older kernel version showed issue with ipw2x00
but that is no longer true so get rid on the name indirection.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull smp hotplug updates from Thomas Gleixner:
"This is the final round of converting the notifier mess to the state
machine. The removal of the notifiers and the related infrastructure
will happen around rc1, as there are conversions outstanding in other
trees.
The whole exercise removed about 2000 lines of code in total and in
course of the conversion several dozen bugs got fixed. The new
mechanism allows to test almost every hotplug step standalone, so
usage sites can exercise all transitions extensively.
There is more room for improvement, like integrating all the
pointlessly different architecture mechanisms of synchronizing,
setting cpus online etc into the core code"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
tracing/rb: Init the CPU mask on allocation
soc/fsl/qbman: Convert to hotplug state machine
soc/fsl/qbman: Convert to hotplug state machine
zram: Convert to hotplug state machine
KVM/PPC/Book3S HV: Convert to hotplug state machine
arm64/cpuinfo: Convert to hotplug state machine
arm64/cpuinfo: Make hotplug notifier symmetric
mm/compaction: Convert to hotplug state machine
iommu/vt-d: Convert to hotplug state machine
mm/zswap: Convert pool to hotplug state machine
mm/zswap: Convert dst-mem to hotplug state machine
mm/zsmalloc: Convert to hotplug state machine
mm/vmstat: Convert to hotplug state machine
mm/vmstat: Avoid on each online CPU loops
mm/vmstat: Drop get_online_cpus() from init_cpu_node_state/vmstat_cpu_dead()
tracing/rb: Convert to hotplug state machine
oprofile/nmi timer: Convert to hotplug state machine
net/iucv: Use explicit clean up labels in iucv_init()
x86/pci/amd-bus: Convert to hotplug state machine
x86/oprofile/nmi: Convert to hotplug state machine
...
* fix a logic bug introduced by a previous cleanup
* fix nl80211 attribute confusing (trying to use
a single attribute for two purposes)
* fix a long-standing BSS leak that happens when an
association attempt is abandoned
-----BEGIN PGP SIGNATURE-----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=HvKt
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-12-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Three fixes:
* fix a logic bug introduced by a previous cleanup
* fix nl80211 attribute confusing (trying to use
a single attribute for two purposes)
* fix a long-standing BSS leak that happens when an
association attempt is abandoned
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When mac80211 abandons an association attempt, it may free
all the data structures, but inform cfg80211 and userspace
about it only by sending the deauth frame it received, in
which case cfg80211 has no link to the BSS struct that was
used and will not cfg80211_unhold_bss() it.
Fix this by providing a way to inform cfg80211 of this with
the BSS entry passed, so that it can clean up properly, and
use this ability in the appropriate places in mac80211.
This isn't ideal: some code is more or less duplicated and
tracing is missing. However, it's a fairly small change and
it's thus easier to backport - cleanups can come later.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sk_drops can be an often written field, do not read it unless
application showed interest.
Note that sk_drops can be read via inet_diag, so applications
can avoid getting this info from every received packet.
In the future, 'reading' sk_drops might require folding per node or per
cpu fields, and thus become even more expensive than today.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFS is not commonly used, so add a jump label to avoid some conditionals
in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow dissection of ICMP(V6) type and code. This should only occur
if a packet is ICMP(V6) and the dissector has FLOW_DISSECTOR_KEY_ICMP set.
There are currently no users of FLOW_DISSECTOR_KEY_ICMP.
A follow-up patch will allow FLOW_DISSECTOR_KEY_ICMP to be used by
the flower classifier.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains a large Netfilter update for net-next,
to summarise:
1) Add support for stateful objects. This series provides a nf_tables
native alternative to the extended accounting infrastructure for
nf_tables. Two initial stateful objects are supported: counters and
quotas. Objects are identified by a user-defined name, you can fetch
and reset them anytime. You can also use a maps to allow fast lookups
using any arbitrary key combination. More info at:
http://marc.info/?l=netfilter-devel&m=148029128323837&w=2
2) On-demand registration of nf_conntrack and defrag hooks per netns.
Register nf_conntrack hooks if we have a stateful ruleset, ie.
state-based filtering or NAT. The new nf_conntrack_default_on sysctl
enables this from newly created netnamespaces. Default behaviour is not
modified. Patches from Florian Westphal.
3) Allocate 4k chunks and then use these for x_tables counter allocation
requests, this improves ruleset load time and also datapath ruleset
evaluation, patches from Florian Westphal.
4) Add support for ebpf to the existing x_tables bpf extension.
From Willem de Bruijn.
5) Update layer 4 checksum if any of the pseudoheader fields is updated.
This provides a limited form of 1:1 stateless NAT that make sense in
specific scenario, eg. load balancing.
6) Add support to flush sets in nf_tables. This series comes with a new
set->ops->deactivate_one() indirection given that we have to walk
over the list of set elements, then deactivate them one by one.
The existing set->ops->deactivate() performs an element lookup that
we don't need.
7) Two patches to avoid cloning packets, thus speed up packet forwarding
via nft_fwd from ingress. From Florian Westphal.
8) Two IPVS patches via Simon Horman: Decrement ttl in all modes to
prevent infinite loops, patch from Dwip Banerjee. And one minor
refactoring from Gao feng.
9) Revisit recent log support for nf_tables netdev families: One patch
to ensure that we correctly handle non-ethernet packets. Another
patch to add missing logger definition for netdev. Patches from
Liping Zhang.
10) Three patches for nft_fib, one to address insufficient register
initialization and another to solve incorrect (although harmless)
byteswap operation. Moreover update xt_rpfilter and nft_fib to match
lbcast packets with zeronet as source, eg. DHCP Discover packets
(0.0.0.0 -> 255.255.255.255). Also from Liping Zhang.
11) Built-in DCCP, SCTP and UDPlite conntrack and NAT support, from
Davide Caratti. While DCCP is rather hopeless lately, and UDPlite has
been broken in many-cast mode for some little time, let's give them a
chance by placing them at the same level as other existing protocols.
Thus, users don't explicitly have to modprobe support for this and
NAT rules work for them. Some people point to the lack of support in
SOHO Linux-based routers that make deployment of new protocols harder.
I guess other middleboxes outthere on the Internet are also to blame.
Anyway, let's see if this has any impact in the midrun.
12) Skip software SCTP software checksum calculation if the NIC comes
with SCTP checksum offload support. From Davide Caratti.
13) Initial core factoring to prepare conversion to hook array. Three
patches from Aaron Conole.
14) Gao Feng made a wrong conversion to switch in the xt_multiport
extension in a patch coming in the previous batch. Fix it in this
batch.
15) Get vmalloc call in sync with kmalloc flags to avoid a warning
and likely OOM killer intervention from x_tables. From Marcelo
Ricardo Leitner.
16) Update Arturo Borrero's email address in all source code headers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo noticed a cache line miss in UDP recvmsg() to access
sk_rxhash, sharing a cache line with sk_drops.
sk_drops might be heavily incremented by cpus handling a flood targeting
this socket.
We might place sk_drops on a separate cache line, but lets try
to avoid wasting 64 bytes per socket just for this, since we have
other bottlenecks to take care of.
sock_rps_record_flow() should only access sk_rxhash for connected
flows.
Testing sk_state for TCP_ESTABLISHED covers most of the cases for
connected sockets, for a zero cost, since system calls using
sock_rps_record_flow() also access sk->sk_prot which is on the
same cache line.
A follow up patch will provide a static_key (Jump Label) since most
hosts do not even use RFS.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for set flushing, that consists of walking over
the set elements if the NFTA_SET_ELEM_LIST_ELEMENTS attribute is set.
This patch requires the following changes:
1) Add set->ops->deactivate_one() operation: This allows us to
deactivate an element from the set element walk path, given we can
skip the lookup that happens in ->deactivate().
2) Add a new nft_trans_alloc_gfp() function since we need to allocate
transactions using GFP_ATOMIC given the set walk path happens with
held rcu_read_lock.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch allows you to refer to stateful objects from set elements.
This provides the infrastructure to create maps where the right hand
side of the mapping is a stateful object.
This allows us to build dictionaries of stateful objects, that you can
use to perform fast lookups using any arbitrary key combination.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Notify on depleted quota objects. The NFT_QUOTA_F_DEPLETED flag
indicates we have reached overquota.
Add pointer to table from nft_object, so we can use it when sending the
depletion notification to userspace.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Introduce nf_tables_obj_notify() to notify internal state changes in
stateful objects. This is used by the quota object to report depletion
in a follow up patch.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds a new NFT_MSG_GETOBJ_RESET command perform an atomic
dump-and-reset of the stateful object. This also comes with add support
for atomic dump and reset for counter and quota objects.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch augments nf_tables to support stateful objects. This new
infrastructure allows you to create, dump and delete stateful objects,
that are identified by a user-defined name.
This patch adds the generic infrastructure, follow up patches add
support for two stateful objects: counters and quotas.
This patch provides a native infrastructure for nf_tables to replace
nfacct, the extended accounting infrastructure for iptables.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
... so we can use current skb instead of working with a clone.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds a new flag that signals the kernel to update layer 4
checksum if the packet field belongs to the layer 4 pseudoheader. This
implicitly provides stateless NAT 1:1 that is useful under very specific
usecases.
Since rules mangling layer 3 fields that are part of the pseudoheader
may potentially convey any layer 4 packet, we have to deal with the
layer 4 checksum adjustment using protocol specific code.
This patch adds support for TCP, UDP and ICMPv6, since they include the
pseudoheader in the layer 4 checksum calculation. ICMP doesn't, so we
can skip it.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_defrag modules for ipv4 and ipv6 export an empty stub function.
Any module that needs the defragmentation hooks registered simply 'calls'
this empty function to create a phony module dependency -- modprobe will
then load the defrag module too.
This extends netfilter ipv4/ipv6 defragmentation modules to delay the hook
registration until the functionality is requested within a network namespace
instead of module load time for all namespaces.
Hooks are only un-registered on module unload or when a namespace that used
such defrag functionality exits.
We have to use struct net for this as the register hooks can be called
before netns initialization here from the ipv4/ipv6 conntrack module
init path.
There is no unregister functionality support, defrag will always be
active once it was requested inside a net namespace.
The reason is that defrag has impact on nft and iptables rulesets
(without defrag we might see framents).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
1) Old code was hard to maintain, due to complex lock chains.
(We probably will be able to remove some kfree_rcu() in callers)
2) Using a single timer to update all estimators does not scale.
3) Code was buggy on 32bit kernel (WRITE_ONCE() on 64bit quantity
is not supposed to work well)
In this rewrite :
- I removed the RB tree that had to be scanned in
gen_estimator_active(). qdisc dumps should be much faster.
- Each estimator has its own timer.
- Estimations are maintained in net_rate_estimator structure,
instead of dirtying the qdisc. Minor, but part of the simplification.
- Reading the estimator uses RCU and a seqcount to provide proper
support for 32bit kernels.
- We reduce memory need when estimators are not used, since
we store a pointer, instead of the bytes/packets counters.
- xt_rateest_mt() no longer has to grab a spinlock.
(In the future, xt_rateest_tg() could be switched to per cpu counters)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-12-03
Here's a set of Bluetooth & 802.15.4 patches for net-next (i.e. 4.10
kernel):
- Fix for a potential NULL deref in the ieee802154 netlink code
- Fix for the ED values of the at86rf2xx driver
- Documentation updates to ieee802154
- Cleanups to u8 vs __u8 usage
- Timer API usage cleanups in HCI drivers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Group fields used in TX path, and keep some cache lines mostly read
to permit sharing among cpus.
Gained two 4 bytes holes on 64bit arches.
Added a place holder for tcp tsq_flags, next to sk_wmem_alloc
to speed up tcp_wfree() in the following patch.
I have not added ____cacheline_aligned_in_smp, this might be done later.
I prefer doing this once inet and tcp/udp sockets reorg is also done.
Tested with both TCP and UDP.
UDP receiver performance under flood increased by ~20 % :
Accessing sk_filter/sk_wq/sk_napi_id no longer stalls because sk_drops
was moved away from a critical cache line, now mostly read and shared.
/* --- cacheline 4 boundary (256 bytes) --- */
unsigned int sk_napi_id; /* 0x100 0x4 */
int sk_rcvbuf; /* 0x104 0x4 */
struct sk_filter * sk_filter; /* 0x108 0x8 */
union {
struct socket_wq * sk_wq; /* 0x8 */
struct socket_wq * sk_wq_raw; /* 0x8 */
}; /* 0x110 0x8 */
struct xfrm_policy * sk_policy[2]; /* 0x118 0x10 */
struct dst_entry * sk_rx_dst; /* 0x128 0x8 */
struct dst_entry * sk_dst_cache; /* 0x130 0x8 */
atomic_t sk_omem_alloc; /* 0x138 0x4 */
int sk_sndbuf; /* 0x13c 0x4 */
/* --- cacheline 5 boundary (320 bytes) --- */
int sk_wmem_queued; /* 0x140 0x4 */
atomic_t sk_wmem_alloc; /* 0x144 0x4 */
long unsigned int sk_tsq_flags; /* 0x148 0x8 */
struct sk_buff * sk_send_head; /* 0x150 0x8 */
struct sk_buff_head sk_write_queue; /* 0x158 0x18 */
__s32 sk_peek_off; /* 0x170 0x4 */
int sk_write_pending; /* 0x174 0x4 */
long int sk_sndtimeo; /* 0x178 0x8 */
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switch (default on) can be used to disable automatic registration
of connection tracking functionality in newly created network
namespaces.
This means that when net namespace goes down (or the tracker protocol
module is unloaded) we *might* have to unregister the hooks.
We can either add another per-netns variable that tells if
the hooks got registered by default, or, alternatively, just call
the protocol _put() function and have the callee deal with a possible
'extra' put() operation that doesn't pair with a get() one.
This uses the latter approach, i.e. a put() without a get has no effect.
Conntrack is still enabled automatically regardless of the new sysctl
setting if the new net namespace requires connection tracking, e.g. when
NAT rules are created.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This makes use of nf_ct_netns_get/put added in previous patch.
We add get/put functions to nf_conntrack_l3proto structure, ipv4 and ipv6
then implement use-count to track how many users (nft or xtables modules)
have a dependency on ipv4 and/or ipv6 connection tracking functionality.
When count reaches zero, the hooks are unregistered.
This delays activation of connection tracking inside a namespace until
stateful firewall rule or nat rule gets added.
This patch breaks backwards compatibility in the sense that connection
tracking won't be active anymore when the protocol tracker module is
loaded. This breaks e.g. setups that ctnetlink for flow accounting and
the like, without any '-m conntrack' packet filter rules.
Followup patch restores old behavour and makes new delayed scheme
optional via sysctl.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
currently aliased to try_module_get/_put.
Will be changed in next patch when we add functions to make use of ->net
argument to store usercount per l3proto tracker.
This is needed to avoid registering the conntrack hooks in all netns and
later only enable connection tracking in those that need conntrack.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
since adf0516845 ("netfilter: remove ip_conntrack* sysctl compat code")
the only user (ipv4 tracker) sets this to an empty stub function.
After this change nf_ct_l3proto_pernet_register() is also empty,
but this will change in a followup patch to add conditional register
of the hooks.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_CT_PROTO_UDPLITE is no more a tristate. When set to y,
connection tracking support for UDPlite protocol is built-in into
nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_udplite,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| udplite| ipv4 | ipv6 |nf_conntrack
---------++--------+--------+--------+--------------
none || 432538 | 828755 | 828676 | 6141434
UDPlite || - | 829649 | 829362 | 6498204
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_CT_PROTO_SCTP is no more a tristate. When set to y, connection
tracking support for SCTP protocol is built-in into nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_sctp,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| sctp | ipv4 | ipv6 | nf_conntrack
---------++--------+--------+--------+--------------
none || 498243 | 828755 | 828676 | 6141434
SCTP || - | 829254 | 829175 | 6547872
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_CT_PROTO_DCCP is no more a tristate. When set to y, connection
tracking support for DCCP protocol is built-in into nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_dccp,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| dccp | ipv4 | ipv6 | nf_conntrack
---------++--------+--------+--------+--------------
none || 469140 | 828755 | 828676 | 6141434
DCCP || - | 830566 | 829935 | 6533526
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In netdev family, we will handle non ethernet packets, so using
eth_hdr(skb)->h_proto is incorrect.
Meanwhile, we can use socket(AF_PACKET...) to sending packets, so
skb->protocol is not always set in bridge family.
Add an extra parameter into nf_log_l2packet to solve this issue.
Fixes: 1fddf4bad0 ("netfilter: nf_log: add packet logging for netdev family")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_NAT_PROTO_UDPLITE is no more a tristate. When set to y, NAT
support for UDPlite protocol is built-in into nf_nat.ko.
footprint test:
(nf_nat_proto_) |udplite || nf_nat
--------------------------+--------++--------
no builtin | 408048 || 2241312
UDPLITE builtin | - || 2577256
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_NAT_PROTO_SCTP is no more a tristate. When set to y, NAT
support for SCTP protocol is built-in into nf_nat.ko.
footprint test:
(nf_nat_proto_) | sctp || nf_nat
--------------------------+--------++--------
no builtin | 428344 || 2241312
SCTP builtin | - || 2597032
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_NAT_PROTO_DCCP is no more a tristate. When set to y, NAT
support for DCCP protocol is built-in into nf_nat.ko.
footprint test:
(nf_nat_proto_) | dccp || nf_nat
--------------------------+--------++--------
no builtin | 409800 || 2241312
DCCP builtin | - || 2578968
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Implemented RFC7527 Enhanced DAD.
IPv6 duplicate address detection can fail if there is some temporary
loopback of Ethernet frames. RFC7527 solves this by including a random
nonce in the NS messages used for DAD, and if an NS is received with the
same nonce it is assumed to be a looped back DAD probe and is ignored.
RFC7527 is enabled by default. Can be disabled by setting both of
conf/{all,interface}/enhanced_dad to zero.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b90eb75494 ("fib: introduce FIB notification infrastructure")
introduced a new notification chain to notify listeners (f.e., switchdev
drivers) about addition and deletion of routes.
However, upon registration to the chain the FIB tables can already be
populated, which means potential listeners will have an incomplete view
of the tables.
Solve that by dumping the FIB tables and replaying the events to the
passed notification block. The dump itself is done using RCU in order
not to starve consumers that need RTNL to make progress.
The integrity of the dump is ensured by reading the FIB change sequence
counter before and after the dump under RTNL. This allows us to avoid
the problematic situation in which the dumping process sends a ENTRY_ADD
notification following ENTRY_DEL generated by another process holding
RTNL.
Callers of the registration function may pass a callback that is
executed in case the dump was inconsistent with current FIB tables.
The number of retries until a consistent dump is achieved is set to a
fixed number to prevent callers from looping for long periods of time.
In case current limit proves to be problematic in the future, it can be
easily converted to be configurable using a sysctl.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patch will enable listeners of the FIB notification chain to
request a dump of the FIB tables. However, since RTNL isn't taken during
the dump, it's possible for the FIB tables to change mid-dump, which
will result in inconsistency between the listener's table and the
kernel's.
Allow listeners to know about changes that occurred mid-dump, by adding
a change sequence counter to each net namespace. The counter is
incremented just before a notification is sent in the FIB chain.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in the previous commit, modules are going to need to take a
reference on fib info and then drop it using fib_info_put().
Add the fib_info_hold() helper to make the code more readable and also
symmetric with fib_info_put().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_generic() function is both a) inline and b) used ~600 times.
It has the following code inside
...
ptr = ng->ptr[id - 1];
...
"id" is never compile time constant so compiler is forced to subtract 1.
And those decrements or LEA [r32 - 1] instructions add up.
We also start id'ing from 1 to catch bugs where pernet sybsystem id
is not initialized and 0. This is quite pointless idea (nothing will
work or immediate interference with first registered subsystem) in
general but it hints what needs to be done for code size reduction.
Namely, overlaying allocation of pointer array and fixed part of
structure in the beginning and using usual base-0 addressing.
Ids are just cookies, their exact values do not matter, so lets start
with 3 on x86_64.
Code size savings (oh boy): -4.2 KB
As usual, ignore the initial compiler stupidity part of the table.
add/remove: 0/0 grow/shrink: 12/670 up/down: 89/-4297 (-4208)
function old new delta
tipc_nametbl_insert_publ 1250 1270 +20
nlmclnt_lookup_host 686 703 +17
nfsd4_encode_fattr 5930 5941 +11
nfs_get_client 1050 1061 +11
register_pernet_operations 333 342 +9
tcf_mirred_init 843 849 +6
tcf_bpf_init 1143 1149 +6
gss_setup_upcall 990 994 +4
idmap_name_to_id 432 434 +2
ops_init 274 275 +1
nfsd_inject_forget_client 259 260 +1
nfs4_alloc_client 612 613 +1
tunnel_key_walker 164 163 -1
...
tipc_bcbase_select_primary 392 360 -32
mac80211_hwsim_new_radio 2808 2767 -41
ipip6_tunnel_ioctl 2228 2186 -42
tipc_bcast_rcv 715 672 -43
tipc_link_build_proto_msg 1140 1089 -51
nfsd4_lock 3851 3796 -55
tipc_mon_rcv 1012 956 -56
Total: Before=156643951, After=156639743, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is precursor to fixing "[id - 1]" bloat inside net_generic().
Name "s" is chosen to complement name "u" often used for dummy unions.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_ok() consists of 3 clauses:
1) int rem >= (int)sizeof(struct nlattr)
2) u16 nla_len >= sizeof(struct nlattr)
3) u16 nla_len <= int rem
The statement is that clause (1) is redundant.
What it does is ensuring that "rem" is a positive number,
so that in clause (3) positive number will be compared to positive number
with no problems.
However, "u16" fully fits into "int" and integers do not change value
when upcasting even to signed type. Negative integers will be rejected
by clause (3) just fine. Small positive integers will be rejected
by transitivity of comparison operator.
NOTE: all of the above DOES NOT apply to nlmsg_ok() where ->nlmsg_len is
u32(!), so 3 clauses AND A CAST TO INT are necessary.
Obligatory space savings report: -1.6 KB
$ ./scripts/bloat-o-meter ../vmlinux-000* ../vmlinux-001*
add/remove: 0/0 grow/shrink: 3/63 up/down: 35/-1692 (-1657)
function old new delta
validate_scan_freqs 142 155 +13
tcf_em_tree_validate 867 879 +12
dcbnl_ieee_del 328 338 +10
netlbl_cipsov4_add_common.isra 218 215 -3
...
ovs_nla_put_actions 888 806 -82
netlbl_cipsov4_add_std 1648 1566 -82
nl80211_parse_sched_scan 2889 2780 -109
ip_tun_from_nlattr 3086 2945 -141
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add socket family, type and protocol to bpf_sock allowing bpf programs
read-only access.
Add __sk_flags_offset[0] to struct sock before the bitfield to
programmtically determine the offset of the unsigned int containing
protocol and type.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support hardware offloading when the device given by the tc
rule is different from the Hardware underline device, extract the mirred
(egress) device from the tc action when a filter is added, using the new
tc_action_ops, get_dev().
Flower caches the information about the mirred device and use it for
calling ndo_setup_tc in filter change, update stats and delete.
Calling ndo_setup_tc of the mirred (egress) device instead of the
ingress device will allow a resolution between the software ingress
device and the underline hardware device.
The resolution will take place inside the offloading driver using
'egress_device' flag added to tc_to_netdev struct which is provided to
the offloading driver.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support to a new tc_action_ops.
get_dev is a general option which allows to get the underline
device when trying to offload a tc rule.
In case of mirred action the returned device is the mirred (egress)
device.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating a difference between two possible cases:
1. Not offloading tc rule since the user sets 'skip_hw' flag.
2. Not offloading tc rule since the device doesn't support offloading.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
jiffies based timestamps allow for easy inference of number of devices
behind NAT translators and also makes tracking of hosts simpler.
commit ceaa1fef65 ("tcp: adding a per-socket timestamp offset")
added the main infrastructure that is needed for per-connection ts
randomization, in particular writing/reading the on-wire tcp header
format takes the offset into account so rest of stack can use normal
tcp_time_stamp (jiffies).
So only two items are left:
- add a tsoffset for request sockets
- extend the tcp isn generator to also return another 32bit number
in addition to the ISN.
Re-use of ISN generator also means timestamps are still monotonically
increasing for same connection quadruple, i.e. PAWS will still work.
Includes fixes from Eric Dumazet.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
This is a large batch of Netfilter fixes for net, they are:
1) Three patches to fix NAT conversion to rhashtable: Switch to rhlist
structure that allows to have several objects with the same key.
Moreover, fix wrong comparison logic in nf_nat_bysource_cmp() as this is
expecting a return value similar to memcmp(). Change location of
the nat_bysource field in the nf_conn structure to avoid zeroing
this as it breaks interaction with SLAB_DESTROY_BY_RCU and lead us
to crashes. From Florian Westphal.
2) Don't allow malformed fragments go through in IPv6, drop them,
otherwise we hit GPF, patch from Florian Westphal.
3) Fix crash if attributes are missing in nft_range, from Liping Zhang.
4) Fix arptables 32-bits userspace 64-bits kernel compat, from Hongxu Jia.
5) Two patches from David Ahern to fix netfilter interaction with vrf.
From David Ahern.
6) Fix element timeout calculation in nf_tables, we take milliseconds
from userspace, but we use jiffies from kernelspace. Patch from
Anders K. Pedersen.
7) Missing validation length netlink attribute for nft_hash, from
Laura Garcia.
8) Fix nf_conntrack_helper documentation, we don't default to off
anymore for a bit of time so let's get this in sync with the code.
I know is late but I think these are important, specifically the NAT
bits, as they are mostly addressing fallout from recent changes. I also
read there are chances to have -rc8, if that is the case, that would
also give us a bit more time to test this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Socket flags aren't updated atomically, so the socket must be locked
while reading the SOCK_ZAPPED flag.
This issue exists for both l2tp_ip and l2tp_ip6. For IPv6, this patch
also brings error handling for __ip6_datagram_connect() failures.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch measures TCP busy time, which is defined as the period
of time when sender has data (or FIN) to send. The time starts when
data is buffered and stops when the write queue is flushed by ACKs
or error events.
Note the busy time does not include SYN time, unless data is
included in SYN (i.e. Fast Open). It does include FIN time even
if the FIN carries no payload. Excluding pure FIN is possible but
would incur one additional test in the fast path, which may not
be worth it.
Signed-off-by: Francis Yan <francisyyan@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the skeleton of the TCP chronograph
instrumentation on sender side limits:
1) idle (unspec)
2) busy sending data other than 3-4 below
3) rwnd-limited
4) sndbuf-limited
The limits are enumerated 'tcp_chrono'. Since a connection in
theory can idle forever, we do not track the actual length of this
uninteresting idle period. For the rest we track how long the sender
spends in each limit. At any point during the life time of a
connection, the sender must be in one of the four states.
If there are multiple conditions worthy of tracking in a chronograph
then the highest priority enum takes precedence over
the other conditions. So that if something "more interesting"
starts happening, stop the previous chrono and start a new one.
The time unit is jiffy(u32) in order to save space in tcp_sock.
This implies application must sample the stats no longer than every
49 days of 1ms jiffy.
Signed-off-by: Francis Yan <francisyyan@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bluetooth.h is not part of user API, so __ variants are not neccessary
here.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some HWs need the VF driver to put part of the packet headers on the
TX descriptor so the e-switch can do proper matching and steering.
The supported modes: none, link, network, transport.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stas Nichiporovich reports oops in nf_nat_bysource_cmp(), trying to
access nf_conn struct at address 0xffffffffffffff50.
This is the result of fetching a null rhash list (struct embedded at
offset 176; 0 - 176 gets us ...fff50).
The problem is that conntrack entries are allocated from a
SLAB_DESTROY_BY_RCU cache, i.e. entries can be free'd and reused
on another cpu while nf nat bysource hash access the same conntrack entry.
Freeing is fine (we hold rcu read lock); zeroing rhlist_head isn't.
-> Move the rhlist struct outside of the memset()-inited area.
Fixes: 7c96643519 ("netfilter: move nat hlist_head to nf_conn")
Reported-by: Stas Nichiporovich <stasn77@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
As Liping Zhang reports, after commit a8b1e36d0d ("netfilter: nft_dynset:
fix element timeout for HZ != 1000"), priv->timeout was stored in jiffies,
while set->timeout was stored in milliseconds. This is inconsistent and
incorrect.
Firstly, we already call msecs_to_jiffies in nft_set_elem_init, so
priv->timeout will be converted to jiffies twice.
Secondly, if the user did not specify the NFTA_DYNSET_TIMEOUT attr,
set->timeout will be used, but we forget to call msecs_to_jiffies
when do update elements.
Fix this by using jiffies internally for traditional sets and doing the
conversions to/from msec when interacting with userspace - as dynset
already does.
This is preferable to doing the conversions, when elements are inserted or
updated, because this can happen very frequently on busy dynsets.
Fixes: a8b1e36d0d ("netfilter: nft_dynset: fix element timeout for HZ != 1000")
Reported-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Anders K. Pedersen <akp@cohaesio.com>
Acked-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
I got offlist bug report about failing connections and high cpu usage.
This happens because we hit 'elasticity' checks in rhashtable that
refuses bucket list exceeding 16 entries.
The nat bysrc hash unfortunately needs to insert distinct objects that
share same key and are identical (have same source tuple), this cannot
be avoided.
Switch to the rhlist interface which is designed for this.
The nulls_base is removed here, I don't think its needed:
A (unlikely) false positive results in unneeded port clash resolution,
a false negative results in packet drop during conntrack confirmation,
when we try to insert the duplicate into main conntrack hash table.
Tested by adding multiple ip addresses to host, then adding
iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
... and then creating multiple connections, from same source port but
different addresses:
for i in $(seq 2000 2032);do nc -p 1234 192.168.7.1 $i > /dev/null & done
(all of these then get hashed to same bysource slot)
Then, to test that nat conflict resultion is working:
nc -s 10.0.0.1 -p 1234 192.168.7.1 2000
nc -s 10.0.0.2 -p 1234 192.168.7.1 2000
tcp .. src=10.0.0.1 dst=192.168.7.1 sport=1234 dport=2000 src=192.168.7.1 dst=192.168.7.10 sport=2000 dport=1024 [ASSURED]
tcp .. src=10.0.0.2 dst=192.168.7.1 sport=1234 dport=2000 src=192.168.7.1 dst=192.168.7.10 sport=2000 dport=1025 [ASSURED]
tcp .. src=192.168.7.10 dst=192.168.7.1 sport=1234 dport=2000 src=192.168.7.1 dst=192.168.7.10 sport=2000 dport=1234 [ASSURED]
tcp .. src=192.168.7.10 dst=192.168.7.1 sport=1234 dport=2001 src=192.168.7.1 dst=192.168.7.10 sport=2001 dport=1234 [ASSURED]
[..]
-> nat altered source ports to 1024 and 1025, respectively.
This can also be confirmed on destination host which shows
ESTAB 0 0 192.168.7.1:2000 192.168.7.10:1024
ESTAB 0 0 192.168.7.1:2000 192.168.7.10:1025
ESTAB 0 0 192.168.7.1:2000 192.168.7.10:1234
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Fixes: 870190a9ec ("netfilter: nat: convert nat bysrc hash to rhashtable")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The hci_get_route() API is used to look up local HCI devices, however
so far it has been incapable of dealing with anything else than the
public address of HCI devices. This completely breaks with LE-only HCI
devices that do not come with a public address, but use a static
random address instead.
This patch exteds the hci_get_route() API with a src_type parameter
that's used for comparing with the right address of each HCI device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
The undo_cwnd fallback in the stack doubles cwnd based on ssthresh,
which un-does reno halving behaviour.
It seems more appropriate to let congctl algorithms pair .ssthresh
and .undo_cwnd properly. Add a 'tcp_reno_undo_cwnd' function and wire it
up for all congestion algorithms that used to rely on the fallback.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument to get_net_ns_by_fd() is a /proc/$PID/ns/net file
descriptor not a pid. Fix the typo.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Rami Rosen <roszenrami@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make struct pernet_operations::id unsigned.
There are 2 reasons to do so:
1)
This field is really an index into an zero based array and
thus is unsigned entity. Using negative value is out-of-bound
access by definition.
2)
On x86_64 unsigned 32-bit data which are mixed with pointers
via array indexing or offsets added or subtracted to pointers
are preffered to signed 32-bit data.
"int" being used as an array index needs to be sign-extended
to 64-bit before being used.
void f(long *p, int i)
{
g(p[i]);
}
roughly translates to
movsx rsi, esi
mov rdi, [rsi+...]
call g
MOVSX is 3 byte instruction which isn't necessary if the variable is
unsigned because x86_64 is zero extending by default.
Now, there is net_generic() function which, you guessed it right, uses
"int" as an array index:
static inline void *net_generic(const struct net *net, int id)
{
...
ptr = ng->ptr[id - 1];
...
}
And this function is used a lot, so those sign extensions add up.
Patch snipes ~1730 bytes on allyesconfig kernel (without all junk
messing with code generation):
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
Unfortunately some functions actually grow bigger.
This is a semmingly random artefact of code generation with register
allocator being used differently. gcc decides that some variable
needs to live in new r8+ registers and every access now requires REX
prefix. Or it is shifted into r12, so [r12+0] addressing mode has to be
used which is longer than [r8]
However, overall balance is in negative direction:
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
function old new delta
nfsd4_lock 3886 3959 +73
tipc_link_build_proto_msg 1096 1140 +44
mac80211_hwsim_new_radio 2776 2808 +32
tipc_mon_rcv 1032 1058 +26
svcauth_gss_legacy_init 1413 1429 +16
tipc_bcbase_select_primary 379 392 +13
nfsd4_exchange_id 1247 1260 +13
nfsd4_setclientid_confirm 782 793 +11
...
put_client_renew_locked 494 480 -14
ip_set_sockfn_get 730 716 -14
geneve_sock_add 829 813 -16
nfsd4_sequence_done 721 703 -18
nlmclnt_lookup_host 708 686 -22
nfsd4_lockt 1085 1063 -22
nfs_get_client 1077 1050 -27
tcf_bpf_init 1106 1076 -30
nfsd4_encode_fattr 5997 5930 -67
Total: Before=154856051, After=154854321, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP busy polling is restricted to connected UDP sockets.
This is because sk_busy_loop() only takes care of one NAPI context.
There are cases where it could be extended.
1) Some hosts receive traffic on a single NIC, with one RX queue.
2) Some applications use SO_REUSEPORT and associated BPF filter
to split the incoming traffic on one UDP socket per RX
queue/thread/cpu
3) Some UDP sockets are used to send/receive traffic for one flow, but
they do not bother with connect()
This patch records the napi_id of first received skb, giving more
reach to busy polling.
Tested:
lpaa23:~# echo 70 >/proc/sys/net/core/busy_read
lpaa24:~# echo 70 >/proc/sys/net/core/busy_read
lpaa23:~# for f in `seq 1 10`; do ./super_netperf 1 -H lpaa24 -t UDP_RR -l 5; done
Before patch :
27867 28870 37324 41060 41215
36764 36838 44455 41282 43843
After patch :
73920 73213 70147 74845 71697
68315 68028 75219 70082 73707
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp transport rhashtable uses hash(lport, dport, daddr) as the key
to hash a node to one chain. If in one host thousands of assocs connect
to one server with the same lport and different laddrs (although it's
not a normal case), all the transports would be hashed into the same
chain.
It may cause to keep returning -EBUSY when inserting a new node, as the
chain is too long and sctp inserts a transport node in a loop, which
could even lead to system hangs there.
The new rhlist interface works for this case that there are many nodes
with the same key in one chain. It puts them into a list then makes this
list be as a node of the chain.
This patch is to replace rhashtable_ interface with rhltable_ interface.
Since a chain would not be too long and it would not return -EBUSY with
this fix when inserting a node, the reinsert loop is also removed here.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the lwtunnel_headroom() function which is called
in ipv4_mtu() and ip6_mtu(), to also return the correct headroom
value when the lwtunnel state is OUTPUT_REDIRECT.
This patch enables e.g. SR-IPv6 encapsulations to work without
manually setting the route mtu.
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sk_busy_loop() can schedule by itself, we can remove
need_resched() check from sk_can_busy_loop()
Also add a const to its struct sock parameter.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch that removed the FIB offload infrastructure was a bit too
aggressive and also removed code needed to clean up us splitting the table
if additional rules were added. Specifically the function
fib_trie_flush_external was called at the end of a new rule being added to
flush the foreign trie entries from the main trie.
I updated the code so that we only call fib_trie_flush_external on the main
table so that we flush the entries for local from main. This way we don't
call it for every rule change which is what was happening previously.
Fixes: 347e3b28c1 ("switchdev: remove FIB offload infrastructure")
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rolf Neugebauer reported very long delays at netns dismantle.
Eric W. Biederman was kind enough to look at this problem
and noticed synchronize_net() occurring from netif_napi_del() that was
added in linux-4.5
Busy polling makes no sense for tunnels NAPI.
If busy poll is used for sessions over tunnels, the poller will need to
poll the physical device queue anyway.
netif_tx_napi_add() could be used here, but function name is misleading,
and renaming it is not stable material, so set NAPI_STATE_NO_BUSY_POLL
bit directly.
This will avoid inserting gro_cells napi structures in napi_hash[]
and avoid the problematic synchronize_net() (per possible cpu) that
Rolf reported.
Fixes: 93d05d4a32 ("net: provide generic busy polling to all NAPI drivers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 850cbaddb5 ("udp: use it's own memory accounting schema")
assumes that the socket proto has memory accounting enabled,
but this is not the case for UDPLITE.
Fix it enabling memory accounting for UDPLITE and performing
fwd allocated memory reclaiming on socket shutdown.
UDP and UDPLITE share now the same memory accounting limits.
Also drop the backlog receive operation, since is no more needed.
Fixes: 850cbaddb5 ("udp: use it's own memory accounting schema")
Reported-by: Andrei Vagin <avagin@gmail.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 14135f30e3 ("inet: fix sleeping inside inet_wait_for_connect()"),
sk_wait_event() needs to fix too, because release_sock() is blocking,
it changes the process state back to running after sleep, which breaks
the previous prepare_to_wait().
Switch to the new wait API.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains a second batch of Netfilter updates for
your net-next tree. This includes a rework of the core hook
infrastructure that improves Netfilter performance by ~15% according to
synthetic benchmarks. Then, a large batch with ipset updates, including
a new hash:ipmac set type, via Jozsef Kadlecsik. This also includes a
couple of assorted updates.
Regarding the core hook infrastructure rework to improve performance,
using this simple drop-all packets ruleset from ingress:
nft add table netdev x
nft add chain netdev x y { type filter hook ingress device eth0 priority 0\; }
nft add rule netdev x y drop
And generating traffic through Jesper Brouer's
samples/pktgen/pktgen_bench_xmit_mode_netif_receive.sh script using -i
option. perf report shows nf_tables calls in its top 10:
17.30% kpktgend_0 [nf_tables] [k] nft_do_chain
15.75% kpktgend_0 [kernel.vmlinux] [k] __netif_receive_skb_core
10.39% kpktgend_0 [nf_tables_netdev] [k] nft_do_chain_netdev
I'm measuring here an improvement of ~15% in performance with this
patchset, so we got +2.5Mpps more. I have used my old laptop Intel(R)
Core(TM) i5-3320M CPU @ 2.60GHz 4-cores.
This rework contains more specifically, in strict order, these patches:
1) Remove compile-time debugging from core.
2) Remove obsolete comments that predate the rcu era. These days it is
well known that a Netfilter hook always runs under rcu_read_lock().
3) Remove threshold handling, this is only used by br_netfilter too.
We already have specific code to handle this from br_netfilter,
so remove this code from the core path.
4) Deprecate NF_STOP, as this is only used by br_netfilter.
5) Place nf_state_hook pointer into xt_action_param structure, so
this structure fits into one single cacheline according to pahole.
This also implicit affects nftables since it also relies on the
xt_action_param structure.
6) Move state->hook_entries into nf_queue entry. The hook_entries
pointer is only required by nf_queue(), so we can store this in the
queue entry instead.
7) use switch() statement to handle verdict cases.
8) Remove hook_entries field from nf_hook_state structure, this is only
required by nf_queue, so store it in nf_queue_entry structure.
9) Merge nf_iterate() into nf_hook_slow() that results in a much more
simple and readable function.
10) Handle NF_REPEAT away from the core, so far the only client is
nf_conntrack_in() and we can restart the packet processing using a
simple goto to jump back there when the TCP requires it.
This update required a second pass to fix fallout, fix from
Arnd Bergmann.
11) Set random seed from nft_hash when no seed is specified from
userspace.
12) Simplify nf_tables expression registration, in a much smarter way
to save lots of boiler plate code, by Liping Zhang.
13) Simplify layer 4 protocol conntrack tracker registration, from
Davide Caratti.
14) Missing CONFIG_NF_SOCKET_IPV4 dependency for udp4_lib_lookup, due
to recent generalization of the socket infrastructure, from Arnd
Bergmann.
15) Then, the ipset batch from Jozsef, he describes it as it follows:
* Cleanup: Remove extra whitespaces in ip_set.h
* Cleanup: Mark some of the helpers arguments as const in ip_set.h
* Cleanup: Group counter helper functions together in ip_set.h
* struct ip_set_skbinfo is introduced instead of open coded fields
in skbinfo get/init helper funcions.
* Use kmalloc() in comment extension helper instead of kzalloc()
because it is unnecessary to zero out the area just before
explicit initialization.
* Cleanup: Split extensions into separate files.
* Cleanup: Separate memsize calculation code into dedicated function.
* Cleanup: group ip_set_put_extensions() and ip_set_get_extensions()
together.
* Add element count to hash headers by Eric B Munson.
* Add element count to all set types header for uniform output
across all set types.
* Count non-static extension memory into memsize calculation for
userspace.
* Cleanup: Remove redundant mtype_expire() arguments, because
they can be get from other parameters.
* Cleanup: Simplify mtype_expire() for hash types by removing
one level of intendation.
* Make NLEN compile time constant for hash types.
* Make sure element data size is a multiple of u32 for the hash set
types.
* Optimize hash creation routine, exit as early as possible.
* Make struct htype per ipset family so nets array becomes fixed size
and thus simplifies the struct htype allocation.
* Collapse same condition body into a single one.
* Fix reported memory size for hash:* types, base hash bucket structure
was not taken into account.
* hash:ipmac type support added to ipset by Tomasz Chilinski.
* Use setup_timer() and mod_timer() instead of init_timer()
by Muhammad Falak R Wani, individually for the set type families.
16) Remove useless connlabel field in struct netns_ct, patch from
Florian Westphal.
17) xt_find_table_lock() doesn't return ERR_PTR() anymore, so simplify
{ip,ip6,arp}tables code that uses this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
since 23014011ba ('netfilter: conntrack: support a fixed size of 128 distinct labels')
this isn't needed anymore.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
With syzkaller help, Marco Grassi found a bug in TCP stack,
crashing in tcp_collapse()
Root cause is that sk_filter() can truncate the incoming skb,
but TCP stack was not really expecting this to happen.
It probably was expecting a simple DROP or ACCEPT behavior.
We first need to make sure no part of TCP header could be removed.
Then we need to adjust TCP_SKB_CB(skb)->end_seq
Many thanks to syzkaller team and Marco for giving us a reproducer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Marco Grassi <marco.gra@gmail.com>
Reported-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The idr_alloc(), idr_remove(), et al. routines all expect IDs to be
signed integers. Therefore make the genl_family member 'id' signed
too.
Signed-off-by: David S. Miller <davem@davemloft.net>
tc_act macro addressed a non existing field, and was not used in the
kernel source.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares for insertion of SRH through setsockopt().
The new source address argument is used when an HMAC field is
present in the SRH, which must be filled. The HMAC signature
process requires the source address as input text.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary functions to compute and check the HMAC signature
of an SR-enabled packet. Two HMAC algorithms are supported: hmac(sha1) and
hmac(sha256).
In order to avoid dynamic memory allocation for each HMAC computation,
a per-cpu ring buffer is allocated for this purpose.
A new per-interface sysctl called seg6_require_hmac is added, allowing a
user-defined policy for processing HMAC-signed SR-enabled packets.
A value of -1 means that the HMAC field will always be ignored.
A value of 0 means that if an HMAC field is present, its validity will
be enforced (the packet is dropped is the signature is incorrect).
Finally, a value of 1 means that any SR-enabled packet that does not
contain an HMAC signature or whose signature is incorrect will be dropped.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a new type of interfaceless lightweight tunnel (SEG6),
enabling the encapsulation and injection of SRH within locally emitted
packets and forwarded packets.
>From a configuration viewpoint, a seg6 tunnel would be configured as follows:
ip -6 ro ad fc00::1/128 encap seg6 mode encap segs fc42::1,fc42::2,fc42::3 dev eth0
Any packet whose destination address is fc00::1 would thus be encapsulated
within an outer IPv6 header containing the SRH with three segments, and would
actually be routed to the first segment of the list. If `mode inline' was
specified instead of `mode encap', then the SRH would be directly inserted
after the IPv6 header without outer encapsulation.
The inline mode is only available if CONFIG_IPV6_SEG6_INLINE is enabled. This
feature was made configurable because direct header insertion may break
several mechanisms such as PMTUD or IPSec AH.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary hooks and structures to provide support
for SR-IPv6 control plane, essentially the Generic Netlink commands
that will be used for userspace control over the Segment Routing
kernel structures.
The genetlink commands provide control over two different structures:
tunnel source and HMAC data. The tunnel source is the source address
that will be used by default when encapsulating packets into an
outer IPv6 header + SRH. If the tunnel source is set to :: then an
address of the outgoing interface will be selected as the source.
The HMAC commands currently just return ENOTSUPP and will be implemented
in a future patch.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement minimal support for processing of SR-enabled packets
as described in
https://tools.ietf.org/html/draft-ietf-6man-segment-routing-header-02.
This patch implements the following operations:
- Intermediate segment endpoint: incrementation of active segment and rerouting.
- Egress for SR-encapsulated packets: decapsulation of outer IPv6 header + SRH
and routing of inner packet.
- Cleanup flag support for SR-inlined packets: removal of SRH if we are the
penultimate segment endpoint.
A per-interface sysctl seg6_enabled is provided, to accept/deny SR-enabled
packets. Default is deny.
This patch does not provide support for HMAC-signed packets.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains a larger than usual batch of Netfilter
fixes for your net tree. This series contains a mixture of old bugs and
recently introduced bugs, they are:
1) Fix a crash when using nft_dynset with nft_set_rbtree, which doesn't
support the set element updates from the packet path. From Liping
Zhang.
2) Fix leak when nft_expr_clone() fails, from Liping Zhang.
3) Fix a race when inserting new elements to the set hash from the
packet path, also from Liping.
4) Handle segmented TCP SIP packets properly, basically avoid that the
INVITE in the allow header create bogus expectations by performing
stricter SIP message parsing, from Ulrich Weber.
5) nft_parse_u32_check() should return signed integer for errors, from
John Linville.
6) Fix wrong allocation instead of connlabels, allocate 16 instead of
32 bytes, from Florian Westphal.
7) Fix compilation breakage when building the ip_vs_sync code with
CONFIG_OPTIMIZE_INLINING on x86, from Arnd Bergmann.
8) Destroy the new set if the transaction object cannot be allocated,
also from Liping Zhang.
9) Use device to route duplicated packets via nft_dup only when set by
the user, otherwise packets may not follow the right route, again
from Liping.
10) Fix wrong maximum genetlink attribute definition in IPVS, from
WANG Cong.
11) Ignore untracked conntrack objects from xt_connmark, from Florian
Westphal.
12) Allow to use conntrack helpers that are registered NFPROTO_UNSPEC
via CT target, otherwise we cannot use the h.245 helper, from
Florian.
13) Revisit garbage collection heuristic in the new workqueue-based
timer approach for conntrack to evict objects earlier, again from
Florian.
14) Fix crash in nf_tables when inserting an element into a verdict map,
from Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
modify registration and deregistration of layer-4 protocol trackers to
facilitate inclusion of new elements into the current list of builtin
protocols. Both builtin (TCP, UDP, ICMP) and non-builtin (DCCP, GRE, SCTP,
UDPlite) layer-4 protocol trackers usually register/deregister themselves
using consecutive calls to nf_ct_l4proto_{,pernet}_{,un}register(...).
This sequence is interrupted and rolled back in case of error; in order to
simplify addition of builtin protocols, the input of the above functions
has been modified to allow registering/unregistering multiple protocols.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Install the callbacks via the state machine. Use multi state support to avoid
custom list handling for the multiple instances.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: netdev@vger.kernel.org
Cc: rt@linutronix.de
Cc: "David S. Miller" <davem@davemloft.net>
Link: http://lkml.kernel.org/r/20161103145021.28528-10-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some basic expressions are built into nf_tables.ko, such as nft_cmp,
nft_lookup, nft_range and so on. But these basic expressions' init
routine is a little ugly, too many goto errX labels, and we forget
to call nft_range_module_exit in the exit routine, although it is
harmless.
Acctually, the init and exit routines of these basic expressions
are same, i.e. do nft_register_expr in the init routine and do
nft_unregister_expr in the exit routine.
So it's better to arrange them into an array and deal with them
together.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add dst port parameter to __ip_tun_set_dst and __ipv6_tun_set_dst
utility functions.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IP tunneling classification supports only IP addresses and key.
Enhance UDP based IP tunneling classification parameters by adding UDP
src and dst port.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New encapsulation keys were added to the flower classifier, which allow
classification according to outer (encapsulation) headers attributes
such as key and IP addresses.
In order to expose those attributes outside flower, add
corresponding enums in the flow dissector.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed for drivers to pick the relevant action when offloading tunnel
key act.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default TX queue length of Ethernet devices have been a magic
constant of 1000, ever since the initial git import.
Looking back in historical trees[1][2] the value used to be 100,
with the same comment "Ethernet wants good queues". The commit[3]
that changed this from 100 to 1000 didn't describe why, but from
conversations with Robert Olsson it seems that it was changed
when Ethernet devices went from 100Mbit/s to 1Gbit/s, because the
link speed increased x10 the queue size were also adjusted. This
value later caused much heartache for the bufferbloat community.
This patch merely moves the value into a defined constant.
[1] https://git.kernel.org/cgit/linux/kernel/git/davem/netdev-vger-cvs.git/
[2] https://git.kernel.org/cgit/linux/kernel/git/tglx/history.git/
[3] https://git.kernel.org/tglx/history/c/98921832c232
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new argument is added to __skb_recv_datagram to provide
an explicit skb destructor, invoked under the receive queue
lock.
The UDP protocol uses such argument to perform memory
reclaiming on dequeue, so that the UDP protocol does not
set anymore skb->desctructor.
Instead explicit memory reclaiming is performed at close() time and
when skbs are removed from the receive queue.
The in kernel UDP protocol users now need to call a
skb_recv_udp() variant instead of skb_recv_datagram() to
properly perform memory accounting on dequeue.
Overall, this allows acquiring only once the receive queue
lock on dequeue.
Tested using pktgen with random src port, 64 bytes packet,
wire-speed on a 10G link as sender and udp_sink as the receiver,
using an l4 tuple rxhash to stress the contention, and one or more
udp_sink instances with reuseport.
nr sinks vanilla patched
1 440 560
3 2150 2300
6 3650 3800
9 4450 4600
12 6250 6450
v1 -> v2:
- do rmem and allocated memory scheduling under the receive lock
- do bulk scheduling in first_packet_length() and in udp_destruct_sock()
- avoid the typdef for the dequeue callback
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that we can use it even after orphaining the skbuff.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use the UID in routing lookups made by protocol connect() and
sendmsg() functions.
- Make sure that routing lookups triggered by incoming packets
(e.g., Path MTU discovery) take the UID of the socket into
account.
- For packets not associated with a userspace socket, (e.g., ping
replies) use UID 0 inside the user namespace corresponding to
the network namespace the socket belongs to. This allows
all namespaces to apply routing and iptables rules to
kernel-originated traffic in that namespaces by matching UID 0.
This is better than using the UID of the kernel socket that is
sending the traffic, because the UID of kernel sockets created
at namespace creation time (e.g., the per-processor ICMP and
TCP sockets) is the UID of the user that created the socket,
which might not be mapped in the namespace.
Tested: compiles allnoconfig, allyesconfig, allmodconfig
Tested: https://android-review.googlesource.com/253302
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Define a new FIB rule attributes, FRA_UID_RANGE, to describe a
range of UIDs.
- Define a RTA_UID attribute for per-UID route lookups and dumps.
- Support passing these attributes to and from userspace via
rtnetlink. The value INVALID_UID indicates no UID was
specified.
- Add a UID field to the flow structures.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocol sockets (struct sock) don't have UIDs, but most of the
time, they map 1:1 to userspace sockets (struct socket) which do.
Various operations such as the iptables xt_owner match need
access to the "UID of a socket", and do so by following the
backpointer to the struct socket. This involves taking
sk_callback_lock and doesn't work when there is no socket
because userspace has already called close().
Simplify this by adding a sk_uid field to struct sock whose value
matches the UID of the corresponding struct socket. The semantics
are as follows:
1. Whenever sk_socket is non-null: sk_uid is the same as the UID
in sk_socket, i.e., matches the return value of sock_i_uid.
Specifically, the UID is set when userspace calls socket(),
fchown(), or accept().
2. When sk_socket is NULL, sk_uid is defined as follows:
- For a socket that no longer has a sk_socket because
userspace has called close(): the previous UID.
- For a cloned socket (e.g., an incoming connection that is
established but on which userspace has not yet called
accept): the UID of the socket it was cloned from.
- For a socket that has never had an sk_socket: UID 0 inside
the user namespace corresponding to the network namespace
the socket belongs to.
Kernel sockets created by sock_create_kern are a special case
of #1 and sk_uid is the user that created them. For kernel
sockets created at network namespace creation time, such as the
per-processor ICMP and TCP sockets, this is the user that created
the network namespace.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some configurations (e.g. geneve interface with default
MTU of 1500 over an ethernet interface with 1500 MTU) result
in the transmission of packets that exceed the configured MTU.
While this should be considered to be a "bad" configuration,
it is still allowed and should not result in the sending
of packets that exceed the configured MTU.
Fix by dropping the assumption in ip_finish_output_gso() that
locally originated gso packets will never need fragmentation.
Basic testing using iperf (observing CPU usage and bandwidth)
have shown no measurable performance impact for traffic not
requiring fragmentation.
Fixes: c7ba65d7b6 ("net: ip: push gso skb forwarding handling down the stack")
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP stack records the largest fragment of a reassembled packet
in IPCB(skb)->frag_max_size. When reading a datagram or raw packet
that arrived fragmented, expose the value to allow applications to
estimate receive path MTU.
Tested:
Sent data over a veth pair of which the source has a small mtu.
Sent data using netcat, received using a dedicated process.
Verified that the cmsg IP_RECVFRAGSIZE is returned only when
data arrives fragmented, and in that cases matches the veth mtu.
ip link add veth0 type veth peer name veth1
ip netns add from
ip netns add to
ip link set dev veth1 netns to
ip netns exec to ip addr add dev veth1 192.168.10.1/24
ip netns exec to ip link set dev veth1 up
ip link set dev veth0 netns from
ip netns exec from ip addr add dev veth0 192.168.10.2/24
ip netns exec from ip link set dev veth0 up
ip netns exec from ip link set dev veth0 mtu 1300
ip netns exec from ethtool -K veth0 ufo off
dd if=/dev/zero bs=1 count=1400 2>/dev/null > payload
ip netns exec to ./recv_cmsg_recvfragsize -4 -u -p 6000 &
ip netns exec from nc -q 1 -u 192.168.10.1 6000 < payload
using github.com/wdebruij/kerneltools/blob/master/tests/recvfragsize.c
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This field is only useful for nf_queue, so store it in the
nf_queue_entry structure instead, away from the core path. Pass
hook_head to nf_hook_slow().
Since we always have a valid entry on the first iteration in
nf_iterate(), we can use 'do { ... } while (entry)' loop instead.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Don't copy relevant fields from hook state structure, instead use the
one that is already available in struct xt_action_param.
This patch also adds a set of new wrapper functions to fetch relevant
hook state structure fields.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Place pointer to hook state in xt_action_param structure instead of
copying the fields that we need. After this change xt_action_param fits
into one cacheline.
This patch also adds a set of new wrapper functions to fetch relevant
hook state structure fields.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
skb->cb may contain data from previous layers. In the observed scenario,
the garbage data were misinterpreted as IP6CB(skb)->frag_max_size, so
that small packets sent through the tunnel are mistakenly fragmented.
This patch unconditionally clears the control buffer in ip6tunnel_xmit(),
which affects ip6_tunnel, ip6_udp_tunnel and ip6_gre. Currently none of
these tunnels set IP6CB(skb)->flags, otherwise it needs to be done earlier.
Cc: stable@vger.kernel.org
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. This includes better integration with the routing subsystem for
nf_tables, explicit notrack support and smaller updates. More
specifically, they are:
1) Add fib lookup expression for nf_tables, from Florian Westphal. This
new expression provides a native replacement for iptables addrtype
and rp_filter matches. This is more flexible though, since we can
populate the kernel flowi representation to inquire fib to
accomodate new usecases, such as RTBH through skb mark.
2) Introduce rt expression for nf_tables, from Anders K. Pedersen. This
new expression allow you to access skbuff route metadata, more
specifically nexthop and classid fields.
3) Add notrack support for nf_tables, to skip conntracking, requested by
many users already.
4) Add boilerplate code to allow to use nf_log infrastructure from
nf_tables ingress.
5) Allow to mangle pkttype from nf_tables prerouting chain, to emulate
the xtables cluster match, from Liping Zhang.
6) Move socket lookup code into generic nf_socket_* infrastructure so
we can provide a native replacement for the xtables socket match.
7) Make sure nfnetlink_queue data that is updated on every packets is
placed in a different cache from read-only data, from Florian Westphal.
8) Handle NF_STOLEN from nf_tables core, also from Florian Westphal.
9) Start round robin number generation in nft_numgen from zero,
instead of n-1, for consistency with xtables statistics match,
patch from Liping Zhang.
10) Set GFP_NOWARN flag in skbuff netlink allocations in nfnetlink_log,
given we retry with a smaller allocation on failure, from Calvin Owens.
11) Cleanup xt_multiport to use switch(), from Gao feng.
12) Remove superfluous check in nft_immediate and nft_cmp, from
Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Move layer 2 packet logging into nf_log_l2packet() that resides in
nf_log_common.c, so this can be shared by both bridge and netdev
families.
This patch adds the boiler plate code to register the netdev logging
family.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add FIB expression, supported for ipv4, ipv6 and inet family (the latter
just dispatches to ipv4 or ipv6 one based on nfproto).
Currently supports fetching output interface index/name and the
rtm_type associated with an address.
This can be used for adding path filtering. rtm_type is useful
to e.g. enforce a strong-end host model where packets
are only accepted if daddr is configured on the interface the
packet arrived on.
The fib expression is a native nftables alternative to the
xtables addrtype and rp_filter matches.
FIB result order for oif/oifname retrieval is as follows:
- if packet is local (skb has rtable, RTF_LOCAL set, this
will also catch looped-back multicast packets), set oif to
the loopback interface.
- if fib lookup returns an error, or result points to local,
store zero result. This means '--local' option of -m rpfilter
is not supported. It is possible to use 'fib type local' or add
explicit saddr/daddr matching rules to create exceptions if this
is really needed.
- store result in the destination register.
In case of multiple routes, search set for desired oif in case
strict matching is requested.
ipv4 and ipv6 behave fib expressions are supposed to behave the same.
[ I have collapsed Arnd Bergmann's ("netfilter: nf_tables: fib warnings")
http://patchwork.ozlabs.org/patch/688615/
to address fallout from this patch after rebasing nf-next, that was
posted to address compilation warnings. --pablo ]
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
