Commit graph

19 commits

Author SHA1 Message Date
Sascha Herrmann
057dad6fcb at86rf230: change irq handling to prevent lockups with edge type irq
Implemented separate irq handling for edge and level type interrupt
configuration. For edge type interrupts calls to disable_irq_nosync()
and enable_irq() are removed. The at86rf230 resets the irq line only
after the irq status register is read. Disabling the irq can lock the
driver in situations where a irq is set by the radio while the driver
is still reading the frame buffer.

With irq_type configuration set to 0 the original behavior is
preserverd.

Additional the irq filter register is set to filter out all unused
interrupts and the irq status register is read in the probe
function to clear the irq line.

Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>

Conflicts:
	drivers/net/ieee802154/at86rf230.c
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-16 16:34:08 -04:00
Sascha Herrmann
43b5abe064 at86rf230: add irq type configuration option
Add option to at86rf230 platform data to configure the type of the
interrupt used by the driver. The irq polarity of the device will
be configured accordingly.

Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-16 16:34:07 -04:00
Wei Yongjun
3d4a131628 mrf24j40: use module_spi_driver to simplify the code
module_spi_driver() makes the code simpler by eliminating
boilerplate code.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-09 13:19:38 -04:00
Alan Ott
cbde8123f6 mrf24j40: Enable link-layer acknowledgement and retry
On the MRF24J40, link-layer acknowledgment request and retry must be
turned on explicitly for each packet.  Turn this on in the hardware based
on the FC_ACK_REQ bit being set in the packet.

Also, now that failure to receive an ACK will cause the hardware to report
failure of transmission, change the log level for this failure to debug
level.

Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-08 12:09:18 -04:00
Sascha Herrmann
f8075a8c94 at86rf230: remove unnecessary / dead code
In at86rf230_probe() lp was first set to dev->priv and a few lines later
dev->priv was set to lp again, without changing lp in between. The call
to ieee802154_unregister_device() before err_irq: was unreachable.

Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-08 12:00:16 -04:00
Werner Almesberger
d87c8c6d15 IEEE 802.15.4: remove get_bsn from "struct ieee802154_mlme_ops"
It served no purpose: we never call it from anywhere in the stack
and the only driver that did implement it (fakehard) merely provided
a dummy value.

There is also considerable doubt whether it would make sense to
even attempt beacon processing at this level in the Linux kernel.

Signed-off-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-08 12:00:16 -04:00
Jingoo Han
4fa0a0ef29 net: ieee802154: mrf24j40: use spi_get_drvdata() and spi_set_drvdata()
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-07 16:48:18 -04:00
stefan@datenfreihafen.org
028889b0b3 ieee802154/at86rf230: Fix register names for RX_AACK_ON and TX_ARET_ON
The register names have been wrong since the beginning but it only showed up now
as they are actualy used for the upcoming auto ACK support.

Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-27 00:52:07 -04:00
stefan@datenfreihafen.org
1486774d69 ieee802154/at86rf230: Implement hardware address filter callback.
Implement the filter function to update short address, pan id and ieee
address on change. Allowing for hardware address filtering needed for
auto ACK.

Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-27 00:52:07 -04:00
Alan Ott
119c331f16 mrf24j40: Fix byte-order of IEEE address
Load the 64-bit Extended (IEEE) address into the hardware in the proper
byte order.

Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-19 10:07:49 -04:00
Alan Ott
cf82dabd29 mrf24j40: Increase max SPI speed to 10MHz
Upon consulting the datasheet further, it does indicates a maximum speed
for SCK at 10MHz.

Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-19 10:07:49 -04:00
Alan Ott
7a1c231886 mrf24j40: Warn if transmit interrupts timeout
Issue a warning if a transmit complete interrupt doesn't happen in time.

Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-19 10:07:49 -04:00
Alan Ott
50861c7eff mrf24j40: pinctrl support
Activate pinctrl settings when used with a DT system.

Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-19 10:07:49 -04:00
Lars-Peter Clausen
c14dd2680b ieee802154: at86rf230: Remove empty suspend/resume callbacks
There is no need to implement empty suspend/resume callbacks if there is nothing
to do during suspend/resume. The drivers will behave the same with no callbacks
or empty callbacks during suspend/resume.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-15 15:35:34 -05:00
Jiri Pirko
aaeb6cdfa5 remove init of dev->perm_addr in drivers
perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-08 18:00:48 -08:00
Bill Pemberton
bb1f460675 ieee802154: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-12-03 11:16:56 -08:00
Linus Torvalds
916082b073 workqueue: avoid using deprecated functions
The network merge brought in a few users of functions that got
deprecated by the workqueue cleanups: the 'system_nrt_wq' is now the
same as the regular system_wq, since all workqueues are now non-
reentrant.

Similarly, remove one use of flush_work_sync() - the regular
flush_work() has become synchronous, and the "_sync()" version is thus
deprecated as being superfluous.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-10-02 16:01:31 -07:00
Alan Ott
3731a334c0 ieee802154: MRF24J40 driver
Driver for the Microchip MRF24J40 802.15.4 WPAN module.

Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-04 14:43:55 -04:00
alex.bluesman.smirnov@gmail.com
0739d643b8 drivers/ieee802154: move ieee802154 drivers to net folder
The IEEE 802.15.4 standard represents a networking protocol. I don't
exactly know why drivers for this protocol are stored into the root
'driver' folder, but better will be to store them with other
networking stuff. Currently there are only 3 drivers available for
IEEE 802.15.4 stack, so lets do it now with the smallest overhead.

Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-30 13:23:56 -04:00